1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
|
/*
i2c-savage4.c - Part of lm_sensors, Linux kernel modules for hardware
monitoring
Copyright (C) 1998-2003 The LM Sensors Team
Alexander Wold <awold@bigfoot.com>
Mark D. Studebaker <mdsxyz123@yahoo.com>
Based on i2c-voodoo3.c.
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
/* This interfaces to the I2C bus of the Savage4 to gain access to
the BT869 and possibly other I2C devices. The DDC bus is not
yet supported because its register is not memory-mapped.
However we leave the DDC code here, commented out, to make
it easier to add later.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/i2c.h>
#include <linux/i2c-algo-bit.h>
#include <asm/io.h>
/* 3DFX defines */
#define PCI_CHIP_SAVAGE3D 0x8A20
#define PCI_CHIP_SAVAGE3D_MV 0x8A21
#define PCI_CHIP_SAVAGE4 0x8A22
#define PCI_CHIP_SAVAGE2000 0x9102
#define PCI_CHIP_PROSAVAGE_PM 0x8A25
#define PCI_CHIP_PROSAVAGE_KM 0x8A26
#define PCI_CHIP_SAVAGE_MX_MV 0x8c10
#define PCI_CHIP_SAVAGE_MX 0x8c11
#define PCI_CHIP_SAVAGE_IX_MV 0x8c12
#define PCI_CHIP_SAVAGE_IX 0x8c13
#define REG 0xff20 /* Serial Port 1 Register */
/* bit locations in the register */
#define DDC_ENAB 0x00040000
#define DDC_SCL_OUT 0x00080000
#define DDC_SDA_OUT 0x00100000
#define DDC_SCL_IN 0x00200000
#define DDC_SDA_IN 0x00400000
#define I2C_ENAB 0x00000020
#define I2C_SCL_OUT 0x00000001
#define I2C_SDA_OUT 0x00000002
#define I2C_SCL_IN 0x00000008
#define I2C_SDA_IN 0x00000010
/* initialization states */
#define INIT2 0x20
#define INIT3 0x04
/* delays */
#define CYCLE_DELAY 10
#define TIMEOUT (HZ / 2)
static void __iomem *ioaddr;
/* The sav GPIO registers don't have individual masks for each bit
so we always have to read before writing. */
static void bit_savi2c_setscl(void *data, int val)
{
unsigned int r;
r = readl(ioaddr + REG);
if(val)
r |= I2C_SCL_OUT;
else
r &= ~I2C_SCL_OUT;
writel(r, ioaddr + REG);
readl(ioaddr + REG); /* flush posted write */
}
static void bit_savi2c_setsda(void *data, int val)
{
unsigned int r;
r = readl(ioaddr + REG);
if(val)
r |= I2C_SDA_OUT;
else
r &= ~I2C_SDA_OUT;
writel(r, ioaddr + REG);
readl(ioaddr + REG); /* flush posted write */
}
/* The GPIO pins are open drain, so the pins always remain outputs.
We rely on the i2c-algo-bit routines to set the pins high before
reading the input from other chips. */
static int bit_savi2c_getscl(void *data)
{
return (0 != (readl(ioaddr + REG) & I2C_SCL_IN));
}
static int bit_savi2c_getsda(void *data)
{
return (0 != (readl(ioaddr + REG) & I2C_SDA_IN));
}
/* Configures the chip */
static int config_s4(struct pci_dev *dev)
{
unsigned long cadr;
/* map memory */
cadr = dev->resource[0].start;
cadr &= PCI_BASE_ADDRESS_MEM_MASK;
ioaddr = ioremap_nocache(cadr, 0x0080000);
if (ioaddr) {
/* writel(0x8160, ioaddr + REG2); */
writel(0x00000020, ioaddr + REG);
dev_info(&dev->dev, "Using Savage4 at %p\n", ioaddr);
return 0;
}
return -ENODEV;
}
static struct i2c_algo_bit_data sav_i2c_bit_data = {
.setsda = bit_savi2c_setsda,
.setscl = bit_savi2c_setscl,
.getsda = bit_savi2c_getsda,
.getscl = bit_savi2c_getscl,
.udelay = CYCLE_DELAY,
.timeout = TIMEOUT
};
static struct i2c_adapter savage4_i2c_adapter = {
.owner = THIS_MODULE,
.name = "I2C Savage4 adapter",
.algo_data = &sav_i2c_bit_data,
};
static struct pci_device_id savage4_ids[] __devinitdata = {
{ PCI_DEVICE(PCI_VENDOR_ID_S3, PCI_CHIP_SAVAGE4) },
{ PCI_DEVICE(PCI_VENDOR_ID_S3, PCI_CHIP_SAVAGE2000) },
{ 0, }
};
MODULE_DEVICE_TABLE (pci, savage4_ids);
static int __devinit savage4_probe(struct pci_dev *dev, const struct pci_device_id *id)
{
int retval;
retval = config_s4(dev);
if (retval)
return retval;
/* set up the sysfs linkage to our parent device */
savage4_i2c_adapter.dev.parent = &dev->dev;
return i2c_bit_add_bus(&savage4_i2c_adapter);
}
static void __devexit savage4_remove(struct pci_dev *dev)
{
i2c_del_adapter(&savage4_i2c_adapter);
iounmap(ioaddr);
}
static struct pci_driver savage4_driver = {
.name = "savage4_smbus",
.id_table = savage4_ids,
.probe = savage4_probe,
.remove = __devexit_p(savage4_remove),
};
static int __init i2c_savage4_init(void)
{
return pci_register_driver(&savage4_driver);
}
static void __exit i2c_savage4_exit(void)
{
pci_unregister_driver(&savage4_driver);
}
MODULE_AUTHOR("Alexander Wold <awold@bigfoot.com> "
"and Mark D. Studebaker <mdsxyz123@yahoo.com>");
MODULE_DESCRIPTION("Savage4 I2C/SMBus driver");
MODULE_LICENSE("GPL");
module_init(i2c_savage4_init);
module_exit(i2c_savage4_exit);
|
