1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
|
/*
*
* BRIEF MODULE DESCRIPTION
* 4G Systems MTX-1 board setup.
*
* Copyright 2003, 2008 MontaVista Software Inc.
* Author: MontaVista Software, Inc. <source@mvista.com>
* Bruno Randolf <bruno.randolf@4g-systems.biz>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/init.h>
#include <asm/mach-au1x00/au1000.h>
extern int (*board_pci_idsel)(unsigned int devsel, int assert);
int mtx1_pci_idsel(unsigned int devsel, int assert);
void board_reset(void)
{
/* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
au_writel(0x00000000, 0xAE00001C);
}
void __init board_setup(void)
{
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
/* Enable USB power switch */
au_writel(au_readl(GPIO2_DIR) | 0x10, GPIO2_DIR);
au_writel(0x100000, GPIO2_OUTPUT);
#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
#ifdef CONFIG_PCI
#if defined(__MIPSEB__)
au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
#else
au_writel(0xf, Au1500_PCI_CFG);
#endif
#endif
/* Initialize sys_pinfunc */
au_writel(SYS_PF_NI2, SYS_PINFUNC);
/* Initialize GPIO */
au_writel(0xFFFFFFFF, SYS_TRIOUTCLR);
au_writel(0x00000001, SYS_OUTPUTCLR); /* set M66EN (PCI 66MHz) to OFF */
au_writel(0x00000008, SYS_OUTPUTSET); /* set PCI CLKRUN# to OFF */
au_writel(0x00000002, SYS_OUTPUTSET); /* set EXT_IO3 ON */
au_writel(0x00000020, SYS_OUTPUTCLR); /* set eth PHY TX_ER to OFF */
/* Enable LED and set it to green */
au_writel(au_readl(GPIO2_DIR) | 0x1800, GPIO2_DIR);
au_writel(0x18000800, GPIO2_OUTPUT);
board_pci_idsel = mtx1_pci_idsel;
printk(KERN_INFO "4G Systems MTX-1 Board\n");
}
int
mtx1_pci_idsel(unsigned int devsel, int assert)
{
#define MTX_IDSEL_ONLY_0_AND_3 0
#if MTX_IDSEL_ONLY_0_AND_3
if (devsel != 0 && devsel != 3) {
printk(KERN_ERR "*** not 0 or 3\n");
return 0;
}
#endif
if (assert && devsel != 0)
/* Suppress signal to Cardbus */
au_writel(0x00000002, SYS_OUTPUTCLR); /* set EXT_IO3 OFF */
else
au_writel(0x00000002, SYS_OUTPUTSET); /* set EXT_IO3 ON */
au_sync_udelay(1);
return 1;
}
|
