blob: 38b2faec4199d9da6ac352f0578be53d76ffcefa (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
|
OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
OMAP MUSB GLUE
- compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
- ti,hwmods : must be "usb_otg_hs"
- multipoint : Should be "1" indicating the musb controller supports
multipoint. This is a MUSB configuration-specific setting.
- num-eps : Specifies the number of endpoints. This is also a
MUSB configuration-specific setting. Should be set to "16"
- ram-bits : Specifies the ram address size. Should be set to "12"
- interface-type : This is a board specific setting to describe the type of
interface between the controller and the phy. It should be "0" or "1"
specifying ULPI and UTMI respectively.
- mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
represents PERIPHERAL.
- power : Should be "50". This signifies the controller can supply up to
100mA when operating in host mode.
- usb-phy : the phandle for the PHY device
- phys : the phandle for the PHY device (used by generic PHY framework)
- phy-names : the names of the PHY corresponding to the PHYs present in the
*phy* phandle.
Optional properties:
- ctrl-module : phandle of the control module this glue uses to write to
mailbox
SOC specific device node entry
usb_otg_hs: usb_otg_hs@4a0ab000 {
compatible = "ti,omap4-musb";
ti,hwmods = "usb_otg_hs";
multipoint = <1>;
num-eps = <16>;
ram-bits = <12>;
ctrl-module = <&omap_control_usb>;
phys = <&usb2_phy>;
phy-names = "usb2-phy";
};
Board specific device node entry
&usb_otg_hs {
interface-type = <1>;
mode = <3>;
power = <50>;
};
OMAP DWC3 GLUE
- compatible : Should be "ti,dwc3"
- ti,hwmods : Should be "usb_otg_ss"
- reg : Address and length of the register set for the device.
- interrupts : The irq number of this device that is used to interrupt the
MPU
- #address-cells, #size-cells : Must be present if the device has sub-nodes
- utmi-mode : controls the source of UTMI/PIPE status for VBUS and OTG ID.
It should be set to "1" for HW mode and "2" for SW mode.
- ranges: the child address space are mapped 1:1 onto the parent address space
Optional Properties:
- extcon : phandle for the extcon device omap dwc3 uses to detect
connect/disconnect events.
- vbus-supply : phandle to the regulator device tree node if needed.
Sub-nodes:
The dwc3 core should be added as subnode to omap dwc3 glue.
- dwc3 :
The binding details of dwc3 can be found in:
Documentation/devicetree/bindings/usb/dwc3.txt
omap_dwc3 {
compatible = "ti,dwc3";
ti,hwmods = "usb_otg_ss";
reg = <0x4a020000 0x1ff>;
interrupts = <0 93 4>;
#address-cells = <1>;
#size-cells = <1>;
utmi-mode = <2>;
ranges;
};
|
