1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
|
* NXP SC16IS7xx advanced Universal Asynchronous Receiver-Transmitter (UART)
* i2c as bus
Required properties:
- compatible: Should be one of the following:
- "nxp,sc16is740" for NXP SC16IS740,
- "nxp,sc16is741" for NXP SC16IS741,
- "nxp,sc16is750" for NXP SC16IS750,
- "nxp,sc16is752" for NXP SC16IS752,
- "nxp,sc16is760" for NXP SC16IS760,
- "nxp,sc16is762" for NXP SC16IS762.
- reg: I2C address of the SC16IS7xx device.
- interrupts: Should contain the UART interrupt
- clocks: Reference to the IC source clock.
OR (when there is no clock provider visible to the platform)
- clock-frequency: The source clock frequency for the IC.
Optional properties:
- gpio-controller: Marks the device node as a GPIO controller.
- #gpio-cells: Should be two. The first cell is the GPIO number and
the second cell is used to specify the GPIO polarity:
0 = active high,
1 = active low.
- irda-mode-ports: An array that lists the indices of the port that
should operate in IrDA mode.
- nxp,modem-control-line-ports: An array that lists the indices of the port that
should have shared GPIO lines configured as
modem control lines.
Example:
sc16is750: sc16is750@51 {
compatible = "nxp,sc16is750";
reg = <0x51>;
clocks = <&clk20m>;
interrupt-parent = <&gpio3>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
gpio-controller;
#gpio-cells = <2>;
};
sc16is752: sc16is752@53 {
compatible = "nxp,sc16is752";
reg = <0x53>;
clocks = <&clk20m>;
interrupt-parent = <&gpio3>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */
gpio-controller; /* Port 0 as GPIOs */
#gpio-cells = <2>;
};
sc16is752: sc16is752@54 {
compatible = "nxp,sc16is752";
reg = <0x54>;
clocks = <&clk20m>;
interrupt-parent = <&gpio3>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
nxp,modem-control-line-ports = <0 1>; /* Ports 0 and 1 as modem control lines */
};
* spi as bus
Required properties:
- compatible: Should be one of the following:
- "nxp,sc16is740" for NXP SC16IS740,
- "nxp,sc16is741" for NXP SC16IS741,
- "nxp,sc16is750" for NXP SC16IS750,
- "nxp,sc16is752" for NXP SC16IS752,
- "nxp,sc16is760" for NXP SC16IS760,
- "nxp,sc16is762" for NXP SC16IS762.
- reg: SPI chip select number.
- interrupts: Specifies the interrupt source of the parent interrupt
controller. The format of the interrupt specifier depends on the
parent interrupt controller.
- clocks: phandle to the IC source clock.
Optional properties:
- gpio-controller: Marks the device node as a GPIO controller.
- #gpio-cells: Should be two. The first cell is the GPIO number and
the second cell is used to specify the GPIO polarity:
0 = active high,
1 = active low.
- irda-mode-ports: An array that lists the indices of the port that
should operate in IrDA mode.
- nxp,modem-control-line-ports: An array that lists the indices of the port that
should have shared GPIO lines configured as
modem control lines.
Example:
sc16is750: sc16is750@0 {
compatible = "nxp,sc16is750";
reg = <0>;
clocks = <&clk20m>;
interrupt-parent = <&gpio3>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
gpio-controller;
#gpio-cells = <2>;
};
sc16is752: sc16is752@1 {
compatible = "nxp,sc16is752";
reg = <1>;
clocks = <&clk20m>;
interrupt-parent = <&gpio3>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */
gpio-controller; /* Port 0 as GPIOs */
#gpio-cells = <2>;
};
sc16is752: sc16is752@2 {
compatible = "nxp,sc16is752";
reg = <2>;
clocks = <&clk20m>;
interrupt-parent = <&gpio3>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
nxp,modem-control-line-ports = <0 1>; /* Ports 0 and 1 as modem control lines */
};
|
