1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
|
# SPDX-License-Identifier: GPL-2.0
# Copyright (C) 2021 Sebastian Reichel
%YAML 1.2
---
$id: "http://devicetree.org/schemas/power/supply/bq24257.yaml#"
$schema: "http://devicetree.org/meta-schemas/core.yaml#"
title: Binding for bq24250, bq24251 and bq24257 Li-Ion Charger
maintainers:
- Sebastian Reichel <sre@kernel.org>
allOf:
- $ref: power-supply.yaml#
properties:
compatible:
enum:
- ti,bq24250
- ti,bq24251
- ti,bq24257
reg:
maxItems: 1
interrupts:
maxItems: 1
ti,battery-regulation-voltage:
$ref: /schemas/types.yaml#/definitions/uint32
description: maximum charging voltage in uV
ti,charge-current:
$ref: /schemas/types.yaml#/definitions/uint32
description: maximum charging current in uA
ti,termination-current:
$ref: /schemas/types.yaml#/definitions/uint32
description: |
charge will be terminated when current in constant-voltage phase
drops below this value (in uA)
pg-gpios:
description: |
GPIO used for connecting the bq2425x device PG (Power Good) pin.
This pin is not available on all devices however it should be used if
possible as this is the recommended way to obtain the charger's input PG
state. If this pin is not specified a software-based approach for PG
detection is used.
maxItems: 1
ti,current-limit:
$ref: /schemas/types.yaml#/definitions/uint32
description: |
The maximum current to be drawn from the charger's input (in uA).
If this property is not specified, the input limit current is set
automatically using USB D+/D- signal based charger type detection.
If the hardware does not support the D+/D- based detection, a default
of 500,000 is used (=500mA) instead.
ti,ovp-voltage:
$ref: /schemas/types.yaml#/definitions/uint32
description: |
Configures the over voltage protection voltage (in uV).
If not specified a default of 6,5000,000 (=6.5V) is used.
ti,in-dpm-voltage:
$ref: /schemas/types.yaml#/definitions/uint32
description: |
Configures the threshold input voltage for the dynamic power path management (in uV).
If not specified a default of 4,360,000 (=4.36V) is used.
required:
- compatible
- reg
- interrupts
- ti,battery-regulation-voltage
- ti,charge-current
- ti,termination-current
additionalProperties: false
examples:
- |
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
i2c0 {
#address-cells = <1>;
#size-cells = <0>;
charger@6a {
compatible = "ti,bq24257";
reg = <0x6a>;
interrupt-parent = <&gpio1>;
interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
ti,battery-regulation-voltage = <4200000>;
ti,charge-current = <1000000>;
ti,termination-current = <50000>;
};
};
- |
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
i2c0 {
#address-cells = <1>;
#size-cells = <0>;
charger@6a {
compatible = "ti,bq24250";
reg = <0x6a>;
interrupt-parent = <&gpio1>;
interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
ti,battery-regulation-voltage = <4200000>;
ti,charge-current = <500000>;
ti,termination-current = <50000>;
ti,current-limit = <900000>;
ti,ovp-voltage = <9500000>;
ti,in-dpm-voltage = <4440000>;
};
};
|
