blob: f1c441bedf68622fb5f762e311a0ccf0b05352b9 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
|
Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
Transceiver
Required properties:
- compatible : must be one of
"sff,sfp" for SFP modules
"sff,sff" for soldered down SFF modules
Optional Properties:
- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial
interface
- mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS)
module presence input gpio signal, active (module absent) high. Must
not be present for SFF modules
- los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal
Indication input gpio signal, active (signal lost) high
- tx-fault-gpios : GPIO phandle and a specifier of the Module Transmitter
Fault input gpio signal, active (fault condition) high
- tx-disable-gpios : GPIO phandle and a specifier of the Transmitter Disable
output gpio signal, active (Tx disable) high
- rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate
Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate
Must not be present for SFF modules
- rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate
Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high:
high Tx rate. Must not be present for SFF modules
Example #1: Direct serdes to SFP connection
sfp_eth3: sfp-eth3 {
compatible = "sff,sfp";
i2c-bus = <&sfp_1g_i2c>;
los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
};
&cps_emac3 {
phy-names = "comphy";
phys = <&cps_comphy5 0>;
sfp = <&sfp_eth3>;
};
Example #2: Serdes to PHY to SFP connection
sfp_eth0: sfp-eth0 {
compatible = "sff,sfp";
i2c-bus = <&sfpp0_i2c>;
los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&cps_sfpp0_pins>;
tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
};
p0_phy: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c45";
pinctrl-names = "default";
pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
reg = <0>;
interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
sfp = <&sfp_eth0>;
};
&cpm_eth0 {
phy = <&p0_phy>;
phy-mode = "10gbase-kr";
};
|
