1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
|
STMicroelectronics STM32 DFSDM ADC device driver
STM32 DFSDM ADC is a sigma delta analog-to-digital converter dedicated to
interface external sigma delta modulators to STM32 micro controllers.
It is mainly targeted for:
- Sigma delta modulators (motor control, metering...)
- PDM microphones (audio digital microphone)
It features up to 8 serial digital interfaces (SPI or Manchester) and
up to 4 filters on stm32h7.
Each child node match with a filter instance.
Contents of a STM32 DFSDM root node:
------------------------------------
Required properties:
- compatible: Should be "st,stm32h7-dfsdm".
- reg: Offset and length of the DFSDM block register set.
- clocks: IP and serial interfaces clocking. Should be set according
to rcc clock ID and "clock-names".
- clock-names: Input clock name "dfsdm" must be defined,
"audio" is optional. If defined CLKOUT is based on the audio
clock, else "dfsdm" is used.
- #interrupt-cells = <1>;
- #address-cells = <1>;
- #size-cells = <0>;
Optional properties:
- spi-max-frequency: Requested only for SPI master mode.
SPI clock OUT frequency (Hz). This clock must be set according
to "clock" property. Frequency must be a multiple of the rcc
clock frequency. If not, SPI CLKOUT frequency will not be
accurate.
- pinctrl-names: Set to "default".
- pinctrl-0: List of phandles pointing to pin configuration
nodes to set pins in mode of operation for dfsdm
on external pin.
Contents of a STM32 DFSDM child nodes:
--------------------------------------
Required properties:
- compatible: Must be:
"st,stm32-dfsdm-adc" for sigma delta ADCs
"st,stm32-dfsdm-dmic" for audio digital microphone.
- reg: Specifies the DFSDM filter instance used.
- interrupts: IRQ lines connected to each DFSDM filter instance.
- st,adc-channels: List of single-ended channels muxed for this ADC.
valid values:
"st,stm32h7-dfsdm" compatibility: 0 to 7.
- st,adc-channel-names: List of single-ended channel names.
- st,filter-order: SinC filter order from 0 to 5.
0: FastSinC
[1-5]: order 1 to 5.
For audio purpose it is recommended to use order 3 to 5.
- #io-channel-cells = <1>: See the IIO bindings section "IIO consumers".
Required properties for "st,stm32-dfsdm-adc" compatibility:
- io-channels: From common IIO binding. Used to pipe external sigma delta
modulator or internal ADC output to DFSDM channel.
This is not required for "st,stm32-dfsdm-pdm" compatibility as
PDM microphone is binded in Audio DT node.
Required properties for "st,stm32-dfsdm-pdm" compatibility:
- #sound-dai-cells: Must be set to 0.
- dma: DMA controller phandle and DMA request line associated to the
filter instance (specified by the field "reg")
- dma-names: Must be "rx"
Optional properties:
- st,adc-channel-types: Single-ended channel input type.
- "SPI_R": SPI with data on rising edge (default)
- "SPI_F": SPI with data on falling edge
- "MANCH_R": manchester codec, rising edge = logic 0, falling edge = logic 1
- "MANCH_F": manchester codec, rising edge = logic 1, falling edge = logic 0
- st,adc-channel-clk-src: Conversion clock source.
- "CLKIN": external SPI clock (CLKIN x)
- "CLKOUT": internal SPI clock (CLKOUT) (default)
- "CLKOUT_F": internal SPI clock divided by 2 (falling edge).
- "CLKOUT_R": internal SPI clock divided by 2 (rising edge).
- st,adc-alt-channel: Must be defined if two sigma delta modulator are
connected on same SPI input.
If not set, channel n is connected to SPI input n.
If set, channel n is connected to SPI input n + 1.
- st,filter0-sync: Set to 1 to synchronize with DFSDM filter instance 0.
Used for multi microphones synchronization.
Example of a sigma delta adc connected on DFSDM SPI port 0
and a pdm microphone connected on DFSDM SPI port 1:
ads1202: simple_sd_adc@0 {
compatible = "ads1202";
#io-channel-cells = <1>;
};
dfsdm: dfsdm@40017000 {
compatible = "st,stm32h7-dfsdm";
reg = <0x40017000 0x400>;
clocks = <&rcc DFSDM1_CK>;
clock-names = "dfsdm";
#interrupt-cells = <1>;
#address-cells = <1>;
#size-cells = <0>;
dfsdm_adc0: filter@0 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <0>;
interrupts = <110>;
st,adc-channels = <0>;
st,adc-channel-names = "sd_adc0";
st,adc-channel-types = "SPI_F";
st,adc-channel-clk-src = "CLKOUT";
io-channels = <&ads1202 0>;
st,filter-order = <3>;
};
dfsdm_pdm1: filter@1 {
compatible = "st,stm32-dfsdm-dmic";
reg = <1>;
interrupts = <111>;
dmas = <&dmamux1 102 0x400 0x00>;
dma-names = "rx";
st,adc-channels = <1>;
st,adc-channel-names = "dmic1";
st,adc-channel-types = "SPI_R";
st,adc-channel-clk-src = "CLKOUT";
st,filter-order = <5>;
};
}
|