1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
|
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/hwmon/ti,ina2xx.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Texas Instruments INA209 family of power/voltage monitors
maintainers:
- Krzysztof Kozlowski <krzk@kernel.org>
description: |
The INA209 is a high-side current shunt and power monitor with
an I2C interface.
Datasheets:
https://www.ti.com/product/INA209
properties:
compatible:
enum:
- silergy,sy24655
- ti,ina209
- ti,ina219
- ti,ina220
- ti,ina226
- ti,ina230
- ti,ina231
- ti,ina237
- ti,ina238
- ti,ina260
reg:
maxItems: 1
"#io-channel-cells":
const: 1
shunt-resistor:
description:
Shunt resistor value in micro-Ohm.
$ref: /schemas/types.yaml#/definitions/uint32
ti,shunt-gain:
description: |
Programmable gain divisor for the shunt voltage accuracy and range. This
property only applies to devices that have configurable PGA/ADCRANGE. The
gain value is used configure the gain and to convert the shunt voltage,
current and power register values when reading measurements from the
device.
For devices that have a configurable PGA (e.g. INA209, INA219, INA220),
the gain value maps directly with the PG bits of the config register.
For devices that have ADCRANGE configuration (e.g. INA238) a shunt-gain
value of 1 maps to ADCRANGE=1 where no gain divisor is applied to the
shunt voltage, and a value of 4 maps to ADCRANGE=0 such that a wider
voltage range is used.
The default value is device dependent, and is defined by the reset value
of PGA/ADCRANGE in the respective configuration registers.
$ref: /schemas/types.yaml#/definitions/uint32
enum: [1, 2, 4, 8]
vs-supply:
description: phandle to the regulator that provides the VS supply typically
in range from 2.7 V to 5.5 V.
ti,alert-polarity-active-high:
description: Alert pin is asserted based on the value of Alert polarity Bit
of Mask/Enable register. Default value is Normal (0 which maps to
active-low open collector). The other value is Inverted
(1 which maps to active-high open collector). Specify this property to set
the alert polarity to active-high.
$ref: /schemas/types.yaml#/definitions/flag
required:
- compatible
- reg
allOf:
- $ref: hwmon-common.yaml#
unevaluatedProperties: false
examples:
- |
i2c {
#address-cells = <1>;
#size-cells = <0>;
power-sensor@44 {
compatible = "ti,ina220";
reg = <0x44>;
#io-channel-cells = <1>;
label = "vdd_3v0";
shunt-resistor = <1000>;
vs-supply = <&vdd_3v0>;
ti,alert-polarity-active-high;
};
};
|
