# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/qcom,eliza-tlmm.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Qualcomm Technologies, Inc. Eliza TLMM block

maintainers:
  - Abel Vesa <abel.vesa@oss.qualcomm.com>

description:
  Top Level Mode Multiplexer pin controller in Qualcomm Eliza SoC.

allOf:
  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#

properties:
  compatible:
    const: qcom,eliza-tlmm

  reg:
    maxItems: 1

  interrupts:
    maxItems: 1

  gpio-reserved-ranges:
    minItems: 1
    maxItems: 93

  gpio-line-names:
    maxItems: 185

patternProperties:
  "-state$":
    oneOf:
      - $ref: "#/$defs/qcom-eliza-tlmm-state"
      - patternProperties:
          "-pins$":
            $ref: "#/$defs/qcom-eliza-tlmm-state"
        additionalProperties: false

$defs:
  qcom-eliza-tlmm-state:
    type: object
    description:
      Pinctrl node's client devices use subnodes for desired pin configuration.
      Client device subnodes use below standard properties.
    $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
    unevaluatedProperties: false

    properties:
      pins:
        description:
          List of gpio pins affected by the properties specified in this
          subnode.
        items:
          oneOf:
            - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9]|18[0-4])$"
            - enum: [ ufs_reset ]
        minItems: 1
        maxItems: 36

      function:
        description:
          Specify the alternative function to be configured for the specified
          pins.
        enum: [ gpio, aoss_cti, atest_char, atest_usb, audio_ext_mclk0,
                audio_ref_clk, cam_mclk, cci_async_in, cci_i2c_scl,
                cci_i2c_sda, cci_timer, coex_uart1_rx, coex_uart1_tx,
                coex_uart2_rx, coex_uart2_tx, dbg_out_clk,
                ddr_bist_complete, ddr_bist_fail, ddr_bist_start,
                ddr_bist_stop, ddr_pxi0, ddr_pxi1, dp0_hot, egpio,
                gcc_gp1, gcc_gp2, gcc_gp3, gnss_adc0, gnss_adc1,
                hdmi_ddc_scl, hdmi_ddc_sda, hdmi_dtest0, hdmi_dtest1,
                hdmi_hot_plug, hdmi_pixel_clk, hdmi_rcv_det, hdmi_tx_cec,
                host2wlan_sol, i2s0_data0, i2s0_data1, i2s0_sck, i2s0_ws,
                ibi_i3c, jitter_bist, mdp_esync0_out, mdp_esync1_out,
                mdp_vsync, mdp_vsync0_out, mdp_vsync11_out,
                mdp_vsync1_out, mdp_vsync2_out, mdp_vsync3_out,
                mdp_vsync_e, nav_gpio0, nav_gpio1, nav_gpio2, nav_gpio3,
                pcie0_clk_req_n, pcie1_clk_req_n, phase_flag,
                pll_bist_sync, pll_clk_aux, prng_rosc0, prng_rosc1,
                prng_rosc2, prng_rosc3, qdss_cti, qdss_gpio_traceclk,
                qdss_gpio_tracectl, qdss_gpio_tracedata, qlink_big_enable,
                qlink_big_request, qlink_little_enable,
                qlink_little_request, qlink_wmss, qspi0, qspi_clk,
                qspi_cs, qup1_se0, qup1_se1, qup1_se2, qup1_se3, qup1_se4,
                qup1_se5, qup1_se6, qup1_se7, qup2_se0, qup2_se1,
                qup2_se2, qup2_se3, qup2_se4, qup2_se5, qup2_se6,
                qup2_se7, resout_gpio, sd_write_protect, sdc1, sdc2,
                sdc2_fb_clk, tb_trig_sdc1, tb_trig_sdc2, tmess_prng0,
                tmess_prng1, tmess_prng2, tmess_prng3, tsense_pwm1,
                tsense_pwm2, tsense_pwm3, tsense_pwm4, uim0_clk,
                uim0_data, uim0_present, uim0_reset, uim1_clk, uim1_data,
                uim1_present, uim1_reset, usb0_hs, usb_phy, vfr_0, vfr_1,
                vsense_trigger_mirnat, wcn_sw_ctrl ]
    required:
      - pins

required:
  - compatible
  - reg

unevaluatedProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/arm-gic.h>

    tlmm: pinctrl@f100000 {
        compatible = "qcom,eliza-tlmm";
        reg = <0x0f100000 0x300000>;

        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;

        gpio-controller;
        #gpio-cells = <2>;

        interrupt-controller;
        #interrupt-cells = <2>;

        gpio-ranges = <&tlmm 0 0 186>;

        gpio-wo-state {
            pins = "gpio1";
            function = "gpio";
        };

        qup-uart14-default-state {
            pins = "gpio18", "gpio19";
            function = "qup2_se5";
            drive-strength = <2>;
            bias-disable;
        };
    };
...