From edd8d90b624e97105d26615d1655da22a3605fff Mon Sep 17 00:00:00 2001
From: Hauke Mehrtens <hauke@hauke-m.de>
Date: Tue, 28 Feb 2012 00:56:04 +0100
Subject: ssb: sprom fix some sizes / signedness

Some parts of the sprom struct are bigger than needed.
The leddc and maxpwr values are just 8 bit long and not 16.
rxpo2g and rxpo5g are signed

I got these information for the open source part of the Broadcom SDK
covering sprom version 1 to 9. rxpo2g contained a negative number on my
bcm5354 based device, this cased an error and Broadcom SDK says this is
signed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 include/linux/ssb/ssb.h | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

(limited to 'include/linux')

diff --git a/include/linux/ssb/ssb.h b/include/linux/ssb/ssb.h
index bbc2612cb64a..f1696213e3b5 100644
--- a/include/linux/ssb/ssb.h
+++ b/include/linux/ssb/ssb.h
@@ -33,8 +33,8 @@ struct ssb_sprom {
 	u8 et1mdcport;		/* MDIO for enet1 */
 	u16 board_rev;		/* Board revision number from SPROM. */
 	u8 country_code;	/* Country Code */
-	u16 leddc_on_time;	/* LED Powersave Duty Cycle On Count */
-	u16 leddc_off_time;	/* LED Powersave Duty Cycle Off Count */
+	u8 leddc_on_time;	/* LED Powersave Duty Cycle On Count */
+	u8 leddc_off_time;	/* LED Powersave Duty Cycle Off Count */
 	u8 ant_available_a;	/* 2GHz antenna available bits (up to 4) */
 	u8 ant_available_bg;	/* 5GHz antenna available bits (up to 4) */
 	u16 pa0b0;
@@ -53,10 +53,10 @@ struct ssb_sprom {
 	u8 gpio1;		/* GPIO pin 1 */
 	u8 gpio2;		/* GPIO pin 2 */
 	u8 gpio3;		/* GPIO pin 3 */
-	u16 maxpwr_bg;		/* 2.4GHz Amplifier Max Power (in dBm Q5.2) */
-	u16 maxpwr_al;		/* 5.2GHz Amplifier Max Power (in dBm Q5.2) */
-	u16 maxpwr_a;		/* 5.3GHz Amplifier Max Power (in dBm Q5.2) */
-	u16 maxpwr_ah;		/* 5.8GHz Amplifier Max Power (in dBm Q5.2) */
+	u8 maxpwr_bg;		/* 2.4GHz Amplifier Max Power (in dBm Q5.2) */
+	u8 maxpwr_al;		/* 5.2GHz Amplifier Max Power (in dBm Q5.2) */
+	u8 maxpwr_a;		/* 5.3GHz Amplifier Max Power (in dBm Q5.2) */
+	u8 maxpwr_ah;		/* 5.8GHz Amplifier Max Power (in dBm Q5.2) */
 	u8 itssi_a;		/* Idle TSSI Target for A-PHY */
 	u8 itssi_bg;		/* Idle TSSI Target for B/G-PHY */
 	u8 tri2g;		/* 2.4GHz TX isolation */
@@ -67,8 +67,8 @@ struct ssb_sprom {
 	u8 txpid5gl[4];		/* 4.9 - 5.1GHz TX power index */
 	u8 txpid5g[4];		/* 5.1 - 5.5GHz TX power index */
 	u8 txpid5gh[4];		/* 5.5 - ...GHz TX power index */
-	u8 rxpo2g;		/* 2GHz RX power offset */
-	u8 rxpo5g;		/* 5GHz RX power offset */
+	s8 rxpo2g;		/* 2GHz RX power offset */
+	s8 rxpo5g;		/* 5GHz RX power offset */
 	u8 rssisav2g;		/* 2GHz RSSI params */
 	u8 rssismc2g;
 	u8 rssismf2g;
-- 
cgit v1.2.3


From f8f8a660ba501ad14617ccd0d91a1ed8ce54d6d0 Mon Sep 17 00:00:00 2001
From: Hauke Mehrtens <hauke@hauke-m.de>
Date: Tue, 28 Feb 2012 00:56:05 +0100
Subject: ssb: remove 5GHz antenna gain from sprom

There is no 2.4 GHz or 5GHz antenna gain stored in sprom. The sprom
just stores the gain values for antenna 1 and 2 or 1 to 4 for more
recent sprom versions. On old devices antenna 2 was used for 5 GHz wifi.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/b43legacy/phy.c |  2 +-
 drivers/ssb/pci.c                    | 41 ++++++++++++------------------------
 drivers/ssb/pcmcia.c                 | 12 ++++-------
 drivers/ssb/sdio.c                   | 12 ++++-------
 include/linux/ssb/ssb.h              |  7 +-----
 5 files changed, 24 insertions(+), 50 deletions(-)

(limited to 'include/linux')

diff --git a/drivers/net/wireless/b43legacy/phy.c b/drivers/net/wireless/b43legacy/phy.c
index 96faaef3661b..950334197f40 100644
--- a/drivers/net/wireless/b43legacy/phy.c
+++ b/drivers/net/wireless/b43legacy/phy.c
@@ -1860,7 +1860,7 @@ void b43legacy_phy_xmitpower(struct b43legacy_wldev *dev)
 	 * which accounts for the factor of 4 */
 #define REG_MAX_PWR 20
 	max_pwr = min(REG_MAX_PWR * 4
-		      - dev->dev->bus->sprom.antenna_gain.ghz24.a0
+		      - dev->dev->bus->sprom.antenna_gain.a0
 		      - 0x6, max_pwr);
 
 	/* find the desired power in Q5.2 - power_level is in dBm
diff --git a/drivers/ssb/pci.c b/drivers/ssb/pci.c
index befa89eac6f3..ed4124469a3a 100644
--- a/drivers/ssb/pci.c
+++ b/drivers/ssb/pci.c
@@ -331,7 +331,6 @@ static void sprom_extract_r123(struct ssb_sprom *out, const u16 *in)
 {
 	int i;
 	u16 v;
-	s8 gain;
 	u16 loc[3];
 
 	if (out->revision == 3)			/* rev 3 moved MAC */
@@ -390,20 +389,12 @@ static void sprom_extract_r123(struct ssb_sprom *out, const u16 *in)
 		SPEX(boardflags_hi, SSB_SPROM2_BFLHI, 0xFFFF, 0);
 
 	/* Extract the antenna gain values. */
-	gain = r123_extract_antgain(out->revision, in,
-				    SSB_SPROM1_AGAIN_BG,
-				    SSB_SPROM1_AGAIN_BG_SHIFT);
-	out->antenna_gain.ghz24.a0 = gain;
-	out->antenna_gain.ghz24.a1 = gain;
-	out->antenna_gain.ghz24.a2 = gain;
-	out->antenna_gain.ghz24.a3 = gain;
-	gain = r123_extract_antgain(out->revision, in,
-				    SSB_SPROM1_AGAIN_A,
-				    SSB_SPROM1_AGAIN_A_SHIFT);
-	out->antenna_gain.ghz5.a0 = gain;
-	out->antenna_gain.ghz5.a1 = gain;
-	out->antenna_gain.ghz5.a2 = gain;
-	out->antenna_gain.ghz5.a3 = gain;
+	out->antenna_gain.a0 = r123_extract_antgain(out->revision, in,
+						    SSB_SPROM1_AGAIN_BG,
+						    SSB_SPROM1_AGAIN_BG_SHIFT);
+	out->antenna_gain.a1 = r123_extract_antgain(out->revision, in,
+						    SSB_SPROM1_AGAIN_A,
+						    SSB_SPROM1_AGAIN_A_SHIFT);
 }
 
 /* Revs 4 5 and 8 have partially shared layout */
@@ -504,16 +495,14 @@ static void sprom_extract_r45(struct ssb_sprom *out, const u16 *in)
 	}
 
 	/* Extract the antenna gain values. */
-	SPEX(antenna_gain.ghz24.a0, SSB_SPROM4_AGAIN01,
+	SPEX(antenna_gain.a0, SSB_SPROM4_AGAIN01,
 	     SSB_SPROM4_AGAIN0, SSB_SPROM4_AGAIN0_SHIFT);
-	SPEX(antenna_gain.ghz24.a1, SSB_SPROM4_AGAIN01,
+	SPEX(antenna_gain.a1, SSB_SPROM4_AGAIN01,
 	     SSB_SPROM4_AGAIN1, SSB_SPROM4_AGAIN1_SHIFT);
-	SPEX(antenna_gain.ghz24.a2, SSB_SPROM4_AGAIN23,
+	SPEX(antenna_gain.a2, SSB_SPROM4_AGAIN23,
 	     SSB_SPROM4_AGAIN2, SSB_SPROM4_AGAIN2_SHIFT);
-	SPEX(antenna_gain.ghz24.a3, SSB_SPROM4_AGAIN23,
+	SPEX(antenna_gain.a3, SSB_SPROM4_AGAIN23,
 	     SSB_SPROM4_AGAIN3, SSB_SPROM4_AGAIN3_SHIFT);
-	memcpy(&out->antenna_gain.ghz5, &out->antenna_gain.ghz24,
-	       sizeof(out->antenna_gain.ghz5));
 
 	sprom_extract_r458(out, in);
 
@@ -602,16 +591,14 @@ static void sprom_extract_r8(struct ssb_sprom *out, const u16 *in)
 	SPEX32(ofdm5ghpo, SSB_SPROM8_OFDM5GHPO, 0xFFFFFFFF, 0);
 
 	/* Extract the antenna gain values. */
-	SPEX(antenna_gain.ghz24.a0, SSB_SPROM8_AGAIN01,
+	SPEX(antenna_gain.a0, SSB_SPROM8_AGAIN01,
 	     SSB_SPROM8_AGAIN0, SSB_SPROM8_AGAIN0_SHIFT);
-	SPEX(antenna_gain.ghz24.a1, SSB_SPROM8_AGAIN01,
+	SPEX(antenna_gain.a1, SSB_SPROM8_AGAIN01,
 	     SSB_SPROM8_AGAIN1, SSB_SPROM8_AGAIN1_SHIFT);
-	SPEX(antenna_gain.ghz24.a2, SSB_SPROM8_AGAIN23,
+	SPEX(antenna_gain.a2, SSB_SPROM8_AGAIN23,
 	     SSB_SPROM8_AGAIN2, SSB_SPROM8_AGAIN2_SHIFT);
-	SPEX(antenna_gain.ghz24.a3, SSB_SPROM8_AGAIN23,
+	SPEX(antenna_gain.a3, SSB_SPROM8_AGAIN23,
 	     SSB_SPROM8_AGAIN3, SSB_SPROM8_AGAIN3_SHIFT);
-	memcpy(&out->antenna_gain.ghz5, &out->antenna_gain.ghz24,
-	       sizeof(out->antenna_gain.ghz5));
 
 	/* Extract cores power info info */
 	for (i = 0; i < ARRAY_SIZE(pwr_info_offset); i++) {
diff --git a/drivers/ssb/pcmcia.c b/drivers/ssb/pcmcia.c
index c821c6b2a6a0..fbafed5b729b 100644
--- a/drivers/ssb/pcmcia.c
+++ b/drivers/ssb/pcmcia.c
@@ -676,14 +676,10 @@ static int ssb_pcmcia_do_get_invariants(struct pcmcia_device *p_dev,
 	case SSB_PCMCIA_CIS_ANTGAIN:
 		GOTO_ERROR_ON(tuple->TupleDataLen != 2,
 			"antg tpl size");
-		sprom->antenna_gain.ghz24.a0 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz24.a1 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz24.a2 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz24.a3 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz5.a0 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz5.a1 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz5.a2 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz5.a3 = tuple->TupleData[1];
+		sprom->antenna_gain.a0 = tuple->TupleData[1];
+		sprom->antenna_gain.a1 = tuple->TupleData[1];
+		sprom->antenna_gain.a2 = tuple->TupleData[1];
+		sprom->antenna_gain.a3 = tuple->TupleData[1];
 		break;
 	case SSB_PCMCIA_CIS_BFLAGS:
 		GOTO_ERROR_ON((tuple->TupleDataLen != 3) &&
diff --git a/drivers/ssb/sdio.c b/drivers/ssb/sdio.c
index 63fd709038ca..b2d36f7736c5 100644
--- a/drivers/ssb/sdio.c
+++ b/drivers/ssb/sdio.c
@@ -551,14 +551,10 @@ int ssb_sdio_get_invariants(struct ssb_bus *bus,
 			case SSB_SDIO_CIS_ANTGAIN:
 				GOTO_ERROR_ON(tuple->size != 2,
 					      "antg tpl size");
-				sprom->antenna_gain.ghz24.a0 = tuple->data[1];
-				sprom->antenna_gain.ghz24.a1 = tuple->data[1];
-				sprom->antenna_gain.ghz24.a2 = tuple->data[1];
-				sprom->antenna_gain.ghz24.a3 = tuple->data[1];
-				sprom->antenna_gain.ghz5.a0 = tuple->data[1];
-				sprom->antenna_gain.ghz5.a1 = tuple->data[1];
-				sprom->antenna_gain.ghz5.a2 = tuple->data[1];
-				sprom->antenna_gain.ghz5.a3 = tuple->data[1];
+				sprom->antenna_gain.a0 = tuple->data[1];
+				sprom->antenna_gain.a1 = tuple->data[1];
+				sprom->antenna_gain.a2 = tuple->data[1];
+				sprom->antenna_gain.a3 = tuple->data[1];
 				break;
 			case SSB_SDIO_CIS_BFLAGS:
 				GOTO_ERROR_ON((tuple->size != 3) &&
diff --git a/include/linux/ssb/ssb.h b/include/linux/ssb/ssb.h
index f1696213e3b5..1de56757e949 100644
--- a/include/linux/ssb/ssb.h
+++ b/include/linux/ssb/ssb.h
@@ -94,12 +94,7 @@ struct ssb_sprom {
 	 * on each band. Values in dBm/4 (Q5.2). Negative gain means the
 	 * loss in the connectors is bigger than the gain. */
 	struct {
-		struct {
-			s8 a0, a1, a2, a3;
-		} ghz24;	/* 2.4GHz band */
-		struct {
-			s8 a0, a1, a2, a3;
-		} ghz5;		/* 5GHz band */
+		s8 a0, a1, a2, a3;
 	} antenna_gain;
 
 	struct {
-- 
cgit v1.2.3


From 3b64e6f9050ff87a746c8e07dc04d97c7f26c5e2 Mon Sep 17 00:00:00 2001
From: Hauke Mehrtens <hauke@hauke-m.de>
Date: Tue, 28 Feb 2012 00:56:06 +0100
Subject: ssb: fix per path sprom vars

On sprom version 4 and 5 there are 4 values for pa_2g, pa_5gl, pa_5g
and pa_5gh, for sprom version 8 and 9 there are only 3. Make the per
path sprom store also work for older sprom versions.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 include/linux/ssb/ssb.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'include/linux')

diff --git a/include/linux/ssb/ssb.h b/include/linux/ssb/ssb.h
index 1de56757e949..49284192521b 100644
--- a/include/linux/ssb/ssb.h
+++ b/include/linux/ssb/ssb.h
@@ -19,7 +19,7 @@ struct ssb_driver;
 struct ssb_sprom_core_pwr_info {
 	u8 itssi_2g, itssi_5g;
 	u8 maxpwr_2g, maxpwr_5gl, maxpwr_5g, maxpwr_5gh;
-	u16 pa_2g[3], pa_5gl[3], pa_5g[3], pa_5gh[3];
+	u16 pa_2g[4], pa_5gl[4], pa_5g[4], pa_5gh[4];
 };
 
 struct ssb_sprom {
-- 
cgit v1.2.3


From 03a5642b6a578d8de355b77efff49bbc45b8be6d Mon Sep 17 00:00:00 2001
From: Hauke Mehrtens <hauke@hauke-m.de>
Date: Tue, 28 Feb 2012 00:56:07 +0100
Subject: ssb: add alpha2

This member contains the country code encoded with two chars

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 include/linux/ssb/ssb.h | 1 +
 1 file changed, 1 insertion(+)

(limited to 'include/linux')

diff --git a/include/linux/ssb/ssb.h b/include/linux/ssb/ssb.h
index 49284192521b..d658de45ffb9 100644
--- a/include/linux/ssb/ssb.h
+++ b/include/linux/ssb/ssb.h
@@ -33,6 +33,7 @@ struct ssb_sprom {
 	u8 et1mdcport;		/* MDIO for enet1 */
 	u16 board_rev;		/* Board revision number from SPROM. */
 	u8 country_code;	/* Country Code */
+	char alpha2[2];		/* Country Code as two chars like EU or US */
 	u8 leddc_on_time;	/* LED Powersave Duty Cycle On Count */
 	u8 leddc_off_time;	/* LED Powersave Duty Cycle Off Count */
 	u8 ant_available_a;	/* 2GHz antenna available bits (up to 4) */
-- 
cgit v1.2.3


From 52aa63f5322aab23e07a52ff8ddd246d34799eb5 Mon Sep 17 00:00:00 2001
From: Hauke Mehrtens <hauke@hauke-m.de>
Date: Tue, 28 Feb 2012 00:56:08 +0100
Subject: ssb: add some missing sprom attributes

This patch extends the sprom struct to contain all sprom attributes
found in sprom version 1 to 9. This was done accordingly to the open
source part of the Broadcom SDK.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 include/linux/ssb/ssb.h | 76 ++++++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 75 insertions(+), 1 deletion(-)

(limited to 'include/linux')

diff --git a/include/linux/ssb/ssb.h b/include/linux/ssb/ssb.h
index d658de45ffb9..d27683180025 100644
--- a/include/linux/ssb/ssb.h
+++ b/include/linux/ssb/ssb.h
@@ -32,6 +32,8 @@ struct ssb_sprom {
 	u8 et0mdcport;		/* MDIO for enet0 */
 	u8 et1mdcport;		/* MDIO for enet1 */
 	u16 board_rev;		/* Board revision number from SPROM. */
+	u16 board_num;		/* Board number from SPROM. */
+	u16 board_type;		/* Board type from SPROM. */
 	u8 country_code;	/* Country Code */
 	char alpha2[2];		/* Country Code as two chars like EU or US */
 	u8 leddc_on_time;	/* LED Powersave Duty Cycle On Count */
@@ -107,7 +109,79 @@ struct ssb_sprom {
 		} ghz5;
 	} fem;
 
-	/* TODO - add any parameters needed from rev 2, 3, 4, 5 or 8 SPROMs */
+	u16 mcs2gpo[8];
+	u16 mcs5gpo[8];
+	u16 mcs5glpo[8];
+	u16 mcs5ghpo[8];
+	u8 opo;
+
+	u8 rxgainerr2ga[3];
+	u8 rxgainerr5gla[3];
+	u8 rxgainerr5gma[3];
+	u8 rxgainerr5gha[3];
+	u8 rxgainerr5gua[3];
+
+	u8 noiselvl2ga[3];
+	u8 noiselvl5gla[3];
+	u8 noiselvl5gma[3];
+	u8 noiselvl5gha[3];
+	u8 noiselvl5gua[3];
+
+	u8 regrev;
+	u8 txchain;
+	u8 rxchain;
+	u8 antswitch;
+	u16 cddpo;
+	u16 stbcpo;
+	u16 bw40po;
+	u16 bwduppo;
+
+	u8 tempthresh;
+	u8 tempoffset;
+	u16 rawtempsense;
+	u8 measpower;
+	u8 tempsense_slope;
+	u8 tempcorrx;
+	u8 tempsense_option;
+	u8 freqoffset_corr;
+	u8 iqcal_swp_dis;
+	u8 hw_iqcal_en;
+	u8 elna2g;
+	u8 elna5g;
+	u8 phycal_tempdelta;
+	u8 temps_period;
+	u8 temps_hysteresis;
+	u8 measpower1;
+	u8 measpower2;
+	u8 pcieingress_war;
+
+	/* power per rate from sromrev 9 */
+	u16 cckbw202gpo;
+	u16 cckbw20ul2gpo;
+	u32 legofdmbw202gpo;
+	u32 legofdmbw20ul2gpo;
+	u32 legofdmbw205glpo;
+	u32 legofdmbw20ul5glpo;
+	u32 legofdmbw205gmpo;
+	u32 legofdmbw20ul5gmpo;
+	u32 legofdmbw205ghpo;
+	u32 legofdmbw20ul5ghpo;
+	u32 mcsbw202gpo;
+	u32 mcsbw20ul2gpo;
+	u32 mcsbw402gpo;
+	u32 mcsbw205glpo;
+	u32 mcsbw20ul5glpo;
+	u32 mcsbw405glpo;
+	u32 mcsbw205gmpo;
+	u32 mcsbw20ul5gmpo;
+	u32 mcsbw405gmpo;
+	u32 mcsbw205ghpo;
+	u32 mcsbw20ul5ghpo;
+	u32 mcsbw405ghpo;
+	u16 mcs32po;
+	u16 legofdm40duppo;
+	u8 sar2g;
+	u8 sar5g;
 };
 
 /* Information about the PCB the circuitry is soldered on. */
-- 
cgit v1.2.3


From 1c9351cf2180924c91bb85e5ba607f24a3d875b1 Mon Sep 17 00:00:00 2001
From: Hauke Mehrtens <hauke@hauke-m.de>
Date: Tue, 28 Feb 2012 00:56:09 +0100
Subject: bcma: export bcma_find_core

This function is needed by the bcm47xx arch code to get the number of
the ieee80211 core.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/bcma/main.c       | 3 ++-
 include/linux/bcma/bcma.h | 1 +
 2 files changed, 3 insertions(+), 1 deletion(-)

(limited to 'include/linux')

diff --git a/drivers/bcma/main.c b/drivers/bcma/main.c
index b8379b90d045..7e138ec21357 100644
--- a/drivers/bcma/main.c
+++ b/drivers/bcma/main.c
@@ -61,7 +61,7 @@ static struct bus_type bcma_bus_type = {
 	.dev_attrs	= bcma_device_attrs,
 };
 
-static struct bcma_device *bcma_find_core(struct bcma_bus *bus, u16 coreid)
+struct bcma_device *bcma_find_core(struct bcma_bus *bus, u16 coreid)
 {
 	struct bcma_device *core;
 
@@ -71,6 +71,7 @@ static struct bcma_device *bcma_find_core(struct bcma_bus *bus, u16 coreid)
 	}
 	return NULL;
 }
+EXPORT_SYMBOL_GPL(bcma_find_core);
 
 static void bcma_release_core_dev(struct device *dev)
 {
diff --git a/include/linux/bcma/bcma.h b/include/linux/bcma/bcma.h
index b9f65fbee42f..46bbd088c4ad 100644
--- a/include/linux/bcma/bcma.h
+++ b/include/linux/bcma/bcma.h
@@ -284,6 +284,7 @@ static inline void bcma_maskset16(struct bcma_device *cc,
 	bcma_write16(cc, offset, (bcma_read16(cc, offset) & mask) | set);
 }
 
+extern struct bcma_device *bcma_find_core(struct bcma_bus *bus, u16 coreid);
 extern bool bcma_core_is_enabled(struct bcma_device *core);
 extern void bcma_core_disable(struct bcma_device *core, u32 flags);
 extern int bcma_core_enable(struct bcma_device *core, u32 flags);
-- 
cgit v1.2.3


From a027237a56f7d519eee5749cfb720e568d0bb0b6 Mon Sep 17 00:00:00 2001
From: Hauke Mehrtens <hauke@hauke-m.de>
Date: Tue, 28 Feb 2012 00:56:10 +0100
Subject: bcma: add support for sprom not found on the device

On SoCs the sprom is stored in the nvram in a special partition on the
flash chip. The nvram contains the sprom for the main bus, but
sometimes also for a pci devices using bcma. This patch makes it
possible for the arch code to register a function to fetch the needed
sprom from the nvram and provide it to the bcma code.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/bcma/sprom.c      | 77 ++++++++++++++++++++++++++++++++++++++++++-----
 include/linux/bcma/bcma.h |  6 ++++
 2 files changed, 75 insertions(+), 8 deletions(-)

(limited to 'include/linux')

diff --git a/drivers/bcma/sprom.c b/drivers/bcma/sprom.c
index ca7752510d5b..916ae255ff64 100644
--- a/drivers/bcma/sprom.c
+++ b/drivers/bcma/sprom.c
@@ -2,6 +2,8 @@
  * Broadcom specific AMBA
  * SPROM reading
  *
+ * Copyright 2011, 2012, Hauke Mehrtens <hauke@hauke-m.de>
+ *
  * Licensed under the GNU/GPL. See COPYING for details.
  */
 
@@ -14,6 +16,45 @@
 #include <linux/dma-mapping.h>
 #include <linux/slab.h>
 
+static int(*get_fallback_sprom)(struct bcma_bus *dev, struct ssb_sprom *out);
+
+/**
+ * bcma_arch_register_fallback_sprom - Registers a method providing a
+ * fallback SPROM if no SPROM is found.
+ *
+ * @sprom_callback: The callback function.
+ *
+ * With this function the architecture implementation may register a
+ * callback handler which fills the SPROM data structure. The fallback is
+ * used for PCI based BCMA devices, where no valid SPROM can be found
+ * in the shadow registers and to provide the SPROM for SoCs where BCMA is
+ * to controll the system bus.
+ *
+ * This function is useful for weird architectures that have a half-assed
+ * BCMA device hardwired to their PCI bus.
+ *
+ * This function is available for architecture code, only. So it is not
+ * exported.
+ */
+int bcma_arch_register_fallback_sprom(int (*sprom_callback)(struct bcma_bus *bus,
+				     struct ssb_sprom *out))
+{
+	if (get_fallback_sprom)
+		return -EEXIST;
+	get_fallback_sprom = sprom_callback;
+
+	return 0;
+}
+
+static int bcma_fill_sprom_with_fallback(struct bcma_bus *bus,
+					 struct ssb_sprom *out)
+{
+	if (!get_fallback_sprom)
+		return -ENOENT;
+
+	return get_fallback_sprom(bus, out);
+}
+
 /**************************************************
  * R/W ops.
  **************************************************/
@@ -246,23 +287,43 @@ static void bcma_sprom_extract_r8(struct bcma_bus *bus, const u16 *sprom)
 	     SSB_SROM8_FEM_ANTSWLUT_SHIFT);
 }
 
+static bool bcma_is_sprom_available(struct bcma_bus *bus)
+{
+	u32 sromctrl;
+
+	if (!(bus->drv_cc.capabilities & BCMA_CC_CAP_SPROM))
+		return false;
+
+	if (bus->drv_cc.core->id.rev >= 32) {
+		sromctrl = bcma_read32(bus->drv_cc.core, BCMA_CC_SROM_CONTROL);
+		return sromctrl & BCMA_CC_SROM_CONTROL_PRESENT;
+	}
+	return true;
+}
+
 int bcma_sprom_get(struct bcma_bus *bus)
 {
 	u16 offset;
 	u16 *sprom;
-	u32 sromctrl;
 	int err = 0;
 
 	if (!bus->drv_cc.core)
 		return -EOPNOTSUPP;
 
-	if (!(bus->drv_cc.capabilities & BCMA_CC_CAP_SPROM))
-		return -ENOENT;
-
-	if (bus->drv_cc.core->id.rev >= 32) {
-		sromctrl = bcma_read32(bus->drv_cc.core, BCMA_CC_SROM_CONTROL);
-		if (!(sromctrl & BCMA_CC_SROM_CONTROL_PRESENT))
-			return -ENOENT;
+	if (!bcma_is_sprom_available(bus)) {
+		/*
+		 * Maybe there is no SPROM on the device?
+		 * Now we ask the arch code if there is some sprom
+		 * available for this device in some other storage.
+		 */
+		err = bcma_fill_sprom_with_fallback(bus, &bus->sprom);
+		if (err) {
+			pr_warn("Using fallback SPROM failed (err %d)\n", err);
+		} else {
+			pr_debug("Using SPROM revision %d provided by"
+				 " platform.\n", bus->sprom.revision);
+			return 0;
+		}
 	}
 
 	sprom = kcalloc(SSB_SPROMSIZE_WORDS_R4, sizeof(u16),
diff --git a/include/linux/bcma/bcma.h b/include/linux/bcma/bcma.h
index 46bbd088c4ad..5af9a075498f 100644
--- a/include/linux/bcma/bcma.h
+++ b/include/linux/bcma/bcma.h
@@ -176,6 +176,12 @@ int __bcma_driver_register(struct bcma_driver *drv, struct module *owner);
 
 extern void bcma_driver_unregister(struct bcma_driver *drv);
 
+/* Set a fallback SPROM.
+ * See kdoc at the function definition for complete documentation. */
+extern int bcma_arch_register_fallback_sprom(
+		int (*sprom_callback)(struct bcma_bus *bus,
+		struct ssb_sprom *out));
+
 struct bcma_bus {
 	/* The MMIO area. */
 	void __iomem *mmio;
-- 
cgit v1.2.3


From 5533513784a88049e19dd2ab380a452b61e5171e Mon Sep 17 00:00:00 2001
From: Ashok Nagarajan <ashok@cozybit.com>
Date: Tue, 28 Feb 2012 17:04:08 -0800
Subject: {nl,cfg,mac}80211: Implement RSSI threshold for mesh peering

Mesh peer links are established only if average rssi of the peer
candidate satisfies the threshold. This is not in 802.11s specification
but was requested by David Fulgham, an open80211s user. This is a way to avoid
marginal peer links with stations that are barely within range.

This patch adds a new mesh configuration parameter, mesh_rssi_threshold. This
feature is supported only for hardwares that report signal in dBm.

Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 include/linux/nl80211.h       |  5 +++++
 include/net/cfg80211.h        |  1 +
 net/mac80211/cfg.c            |  8 ++++++++
 net/mac80211/debugfs_netdev.c |  2 ++
 net/mac80211/mesh_plink.c     | 16 +++++++++++++++-
 net/wireless/mesh.c           |  3 +++
 net/wireless/nl80211.c        |  5 +++++
 7 files changed, 39 insertions(+), 1 deletion(-)

(limited to 'include/linux')

diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h
index be35a68746a7..38fda5ee57f5 100644
--- a/include/linux/nl80211.h
+++ b/include/linux/nl80211.h
@@ -2112,6 +2112,10 @@ enum nl80211_mntr_flags {
  * @NL80211_MESHCONF_FORWARDING: set Mesh STA as forwarding or non-forwarding
  * or forwarding entity (default is TRUE - forwarding entity)
  *
+ * @NL80211_MESHCONF_RSSI_THRESHOLD: RSSI threshold in dBm. This specifies the
+ * threshold for average signal strength of candidate station to establish
+ * a peer link.
+ *
  * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute
  *
  * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use
@@ -2137,6 +2141,7 @@ enum nl80211_meshconf_params {
 	NL80211_MESHCONF_GATE_ANNOUNCEMENTS,
 	NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL,
 	NL80211_MESHCONF_FORWARDING,
+	NL80211_MESHCONF_RSSI_THRESHOLD,
 
 	/* keep last */
 	__NL80211_MESHCONF_ATTR_AFTER_LAST,
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 0178c7489373..b4e015c90885 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -809,6 +809,7 @@ struct mesh_config {
 	 * Still keeping the same nomenclature to be in sync with the spec. */
 	bool  dot11MeshGateAnnouncementProtocol;
 	bool dot11MeshForwarding;
+	s32 rssi_threshold;
 };
 
 /**
diff --git a/net/mac80211/cfg.c b/net/mac80211/cfg.c
index 6a77d4c910f9..ab31cc56a2fb 100644
--- a/net/mac80211/cfg.c
+++ b/net/mac80211/cfg.c
@@ -1314,6 +1314,14 @@ static int ieee80211_update_mesh_config(struct wiphy *wiphy,
 	}
 	if (_chg_mesh_attr(NL80211_MESHCONF_FORWARDING, mask))
 		conf->dot11MeshForwarding = nconf->dot11MeshForwarding;
+	if (_chg_mesh_attr(NL80211_MESHCONF_RSSI_THRESHOLD, mask)) {
+		/* our RSSI threshold implementation is supported only for
+		 * devices that report signal in dBm.
+		 */
+		if (!(sdata->local->hw.flags & IEEE80211_HW_SIGNAL_DBM))
+			return -ENOTSUPP;
+		conf->rssi_threshold = nconf->rssi_threshold;
+	}
 	return 0;
 }
 
diff --git a/net/mac80211/debugfs_netdev.c b/net/mac80211/debugfs_netdev.c
index 510ed1dab3c7..9f484d8905fd 100644
--- a/net/mac80211/debugfs_netdev.c
+++ b/net/mac80211/debugfs_netdev.c
@@ -443,6 +443,7 @@ IEEE80211_IF_FILE(dot11MeshGateAnnouncementProtocol,
 IEEE80211_IF_FILE(dot11MeshHWMPRannInterval,
 		u.mesh.mshcfg.dot11MeshHWMPRannInterval, DEC);
 IEEE80211_IF_FILE(dot11MeshForwarding, u.mesh.mshcfg.dot11MeshForwarding, DEC);
+IEEE80211_IF_FILE(rssi_threshold, u.mesh.mshcfg.rssi_threshold, DEC);
 #endif
 
 
@@ -581,6 +582,7 @@ static void add_mesh_config(struct ieee80211_sub_if_data *sdata)
 	MESHPARAMS_ADD(dot11MeshHWMPRootMode);
 	MESHPARAMS_ADD(dot11MeshHWMPRannInterval);
 	MESHPARAMS_ADD(dot11MeshGateAnnouncementProtocol);
+	MESHPARAMS_ADD(rssi_threshold);
 #undef MESHPARAMS_ADD
 }
 #endif
diff --git a/net/mac80211/mesh_plink.c b/net/mac80211/mesh_plink.c
index 8806e5ef8ffe..80ce52772538 100644
--- a/net/mac80211/mesh_plink.c
+++ b/net/mac80211/mesh_plink.c
@@ -31,6 +31,11 @@
 #define dot11MeshHoldingTimeout(s) (s->u.mesh.mshcfg.dot11MeshHoldingTimeout)
 #define dot11MeshMaxPeerLinks(s) (s->u.mesh.mshcfg.dot11MeshMaxPeerLinks)
 
+#define sta_meets_rssi_threshold(sta, sdata) \
+		(sdata->u.mesh.mshcfg.rssi_threshold == 0 ||\
+		(s8) -ewma_read(&sta->avg_signal) > \
+		sdata->u.mesh.mshcfg.rssi_threshold)
+
 enum plink_event {
 	PLINK_UNDEFINED,
 	OPN_ACPT,
@@ -301,7 +306,8 @@ void mesh_neighbour_update(u8 *hw_addr, u32 rates,
 	if (mesh_peer_accepts_plinks(elems) &&
 			sta->plink_state == NL80211_PLINK_LISTEN &&
 			sdata->u.mesh.accepting_plinks &&
-			sdata->u.mesh.mshcfg.auto_open_plinks)
+			sdata->u.mesh.mshcfg.auto_open_plinks &&
+			sta_meets_rssi_threshold(sta, sdata))
 		mesh_plink_open(sta);
 
 	rcu_read_unlock();
@@ -531,6 +537,14 @@ void mesh_rx_plink_frame(struct ieee80211_sub_if_data *sdata, struct ieee80211_m
 		return;
 	}
 
+	if (ftype == WLAN_SP_MESH_PEERING_OPEN &&
+	    !sta_meets_rssi_threshold(sta, sdata)) {
+		mpl_dbg("Mesh plink: %pM does not meet rssi threshold\n",
+			sta->sta.addr);
+		rcu_read_unlock();
+		return;
+	}
+
 	if (sta && !test_sta_flag(sta, WLAN_STA_AUTH)) {
 		mpl_dbg("Mesh plink: Action frame from non-authed peer\n");
 		rcu_read_unlock();
diff --git a/net/wireless/mesh.c b/net/wireless/mesh.c
index 9d3e3b6bfcf4..ba21ab22187b 100644
--- a/net/wireless/mesh.c
+++ b/net/wireless/mesh.c
@@ -23,6 +23,8 @@
 #define MESH_PERR_MIN_INT	100
 #define MESH_DIAM_TRAVERSAL_TIME 50
 
+#define MESH_RSSI_THRESHOLD	0
+
 /*
  * A path will be refreshed if it is used PATH_REFRESH_TIME milliseconds
  * before timing out.  This way it will remain ACTIVE and no data frames
@@ -56,6 +58,7 @@ const struct mesh_config default_mesh_config = {
 	.dot11MeshHWMPRannInterval = MESH_RANN_INTERVAL,
 	.dot11MeshGateAnnouncementProtocol = false,
 	.dot11MeshForwarding = true,
+	.rssi_threshold = MESH_RSSI_THRESHOLD,
 };
 
 const struct mesh_setup default_mesh_setup = {
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index 1998c3682774..25a470abd21d 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -3290,6 +3290,8 @@ static int nl80211_get_mesh_config(struct sk_buff *skb,
 			cur_params.dot11MeshGateAnnouncementProtocol);
 	NLA_PUT_U8(msg, NL80211_MESHCONF_FORWARDING,
 			cur_params.dot11MeshForwarding);
+	NLA_PUT_U32(msg, NL80211_MESHCONF_RSSI_THRESHOLD,
+			cur_params.rssi_threshold);
 	nla_nest_end(msg, pinfoattr);
 	genlmsg_end(msg, hdr);
 	return genlmsg_reply(msg, info);
@@ -3322,6 +3324,7 @@ static const struct nla_policy nl80211_meshconf_params_policy[NL80211_MESHCONF_A
 	[NL80211_MESHCONF_HWMP_RANN_INTERVAL] = { .type = NLA_U16 },
 	[NL80211_MESHCONF_GATE_ANNOUNCEMENTS] = { .type = NLA_U8 },
 	[NL80211_MESHCONF_FORWARDING] = { .type = NLA_U8 },
+	[NL80211_MESHCONF_RSSI_THRESHOLD] = { .type = NLA_U32},
 };
 
 static const struct nla_policy
@@ -3413,6 +3416,8 @@ do {\
 			nla_get_u8);
 	FILL_IN_MESH_PARAM_IF_SET(tb, cfg, dot11MeshForwarding,
 			mask, NL80211_MESHCONF_FORWARDING, nla_get_u8);
+	FILL_IN_MESH_PARAM_IF_SET(tb, cfg, rssi_threshold,
+			mask, NL80211_MESHCONF_RSSI_THRESHOLD, nla_get_u32);
 	if (mask_out)
 		*mask_out = mask;
 
-- 
cgit v1.2.3


From 1b658f118b11de3c4052ed8cbdd5803cd1fa5670 Mon Sep 17 00:00:00 2001
From: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Date: Fri, 2 Mar 2012 15:50:02 +0530
Subject: cfg80211: Add an attribute to set inactivity timeout in AP mode

This patch adds an attribute, NL80211_ATTR_INACTIVITY_TIMEOUT,
to set the inactivity timeout which can be used to remove the
station in AP mode. This can be passed in NL80211_CMD_START_AP
and used by the drivers which have AP MLME in firmware but
don't support get_station() properly. To disable inactivity
timer in userspace, wpa_s for example, there is a new flag,
NL80211_FEATURE_INACTIVITY_TIMER, in nl80211_feature_flags
through which drivers can register their capability to use
the inactivity timeout to free the stations.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 include/linux/nl80211.h | 15 +++++++++++++--
 include/net/cfg80211.h  |  2 ++
 net/wireless/nl80211.c  |  8 ++++++++
 3 files changed, 23 insertions(+), 2 deletions(-)

(limited to 'include/linux')

diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h
index 38fda5ee57f5..9f46c62b1eee 100644
--- a/include/linux/nl80211.h
+++ b/include/linux/nl80211.h
@@ -168,8 +168,8 @@
  *	%NL80211_ATTR_DTIM_PERIOD, %NL80211_ATTR_SSID,
  *	%NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE,
  *	%NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS,
- *	%NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY and
- *	%NL80211_ATTR_AUTH_TYPE.
+ *	%NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY,
+ *	%NL80211_ATTR_AUTH_TYPE and %NL80211_ATTR_INACTIVITY_TIMEOUT.
  * @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP
  * @NL80211_CMD_STOP_AP: Stop AP operation on the given interface
  * @NL80211_CMD_DEL_BEACON: old alias for %NL80211_CMD_STOP_AP
@@ -1197,6 +1197,12 @@ enum nl80211_commands {
  * @NL80211_ATTR_NOACK_MAP: This u16 bitmap contains the No Ack Policy of
  *      up to 16 TIDs.
  *
+ * @NL80211_ATTR_INACTIVITY_TIMEOUT: timeout value in seconds, this can be
+ *	used by the drivers which has MLME in firmware and does not have support
+ *	to report per station tx/rx activity to free up the staion entry from
+ *	the list. This needs to be used when the driver advertises the
+ *	capability to timeout the stations.
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -1442,6 +1448,8 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_NOACK_MAP,
 
+	NL80211_ATTR_INACTIVITY_TIMEOUT,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -2809,10 +2817,13 @@ enum nl80211_ap_sme_features {
  *	TX status to the socket error queue when requested with the
  *	socket option.
  * @NL80211_FEATURE_HT_IBSS: This driver supports IBSS with HT datarates.
+ * @NL80211_FEATURE_INACTIVITY_TIMER: This driver takes care of freeing up
+ *	the connected inactive stations in AP mode.
  */
 enum nl80211_feature_flags {
 	NL80211_FEATURE_SK_TX_STATUS	= 1 << 0,
 	NL80211_FEATURE_HT_IBSS		= 1 << 1,
+	NL80211_FEATURE_INACTIVITY_TIMER = 1 << 2,
 };
 
 /**
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index d640a39d9513..804805827736 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -413,6 +413,7 @@ struct cfg80211_beacon_data {
  * @crypto: crypto settings
  * @privacy: the BSS uses privacy
  * @auth_type: Authentication type (algorithm)
+ * @inactivity_timeout: time in seconds to determine station's inactivity.
  */
 struct cfg80211_ap_settings {
 	struct cfg80211_beacon_data beacon;
@@ -424,6 +425,7 @@ struct cfg80211_ap_settings {
 	struct cfg80211_crypto_settings crypto;
 	bool privacy;
 	enum nl80211_auth_type auth_type;
+	int inactivity_timeout;
 };
 
 /**
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index 25a470abd21d..4b6afc338aac 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -204,6 +204,7 @@ static const struct nla_policy nl80211_policy[NL80211_ATTR_MAX+1] = {
 		.len = NL80211_HT_CAPABILITY_LEN
 	},
 	[NL80211_ATTR_NOACK_MAP] = { .type = NLA_U16 },
+	[NL80211_ATTR_INACTIVITY_TIMEOUT] = { .type = NLA_U16 },
 };
 
 /* policy for the key attributes */
@@ -2214,6 +2215,13 @@ static int nl80211_start_ap(struct sk_buff *skb, struct genl_info *info)
 	if (err)
 		return err;
 
+	if (info->attrs[NL80211_ATTR_INACTIVITY_TIMEOUT]) {
+		if (!(rdev->wiphy.features & NL80211_FEATURE_INACTIVITY_TIMER))
+			return -EOPNOTSUPP;
+		params.inactivity_timeout = nla_get_u16(
+			info->attrs[NL80211_ATTR_INACTIVITY_TIMEOUT]);
+	}
+
 	err = rdev->ops->start_ap(&rdev->wiphy, dev, &params);
 	if (!err)
 		wdev->beacon_interval = params.beacon_interval;
-- 
cgit v1.2.3


From 804483e90794256f9ed53e795ffbf1e94de237c8 Mon Sep 17 00:00:00 2001
From: Johannes Berg <johannes.berg@intel.com>
Date: Mon, 5 Mar 2012 22:18:41 +0100
Subject: cfg80211/mac80211: report signal strength for mgmt frames

Add the signal strength (in dBm only for now) to
frames that are received via nl80211's various
frame APIs.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/ath/ath6kl/wmi.c |  6 ++++--
 include/linux/nl80211.h               |  6 ++++++
 include/net/cfg80211.h                |  8 +++++---
 net/mac80211/rx.c                     | 13 +++++++++++--
 net/wireless/mlme.c                   |  7 ++++---
 net/wireless/nl80211.c                |  9 +++++++--
 net/wireless/nl80211.h                |  3 ++-
 7 files changed, 39 insertions(+), 13 deletions(-)

(limited to 'include/linux')

diff --git a/drivers/net/wireless/ath/ath6kl/wmi.c b/drivers/net/wireless/ath/ath6kl/wmi.c
index 18fa9aa8af92..97abf4699b41 100644
--- a/drivers/net/wireless/ath/ath6kl/wmi.c
+++ b/drivers/net/wireless/ath/ath6kl/wmi.c
@@ -556,7 +556,8 @@ static int ath6kl_wmi_rx_probe_req_event_rx(struct wmi *wmi, u8 *datap, int len,
 		   dlen, freq, vif->probe_req_report);
 
 	if (vif->probe_req_report || vif->nw_type == AP_NETWORK)
-		cfg80211_rx_mgmt(vif->ndev, freq, ev->data, dlen, GFP_ATOMIC);
+		cfg80211_rx_mgmt(vif->ndev, freq, 0,
+				 ev->data, dlen, GFP_ATOMIC);
 
 	return 0;
 }
@@ -595,7 +596,8 @@ static int ath6kl_wmi_rx_action_event_rx(struct wmi *wmi, u8 *datap, int len,
 		return -EINVAL;
 	}
 	ath6kl_dbg(ATH6KL_DBG_WMI, "rx_action: len=%u freq=%u\n", dlen, freq);
-	cfg80211_rx_mgmt(vif->ndev, freq, ev->data, dlen, GFP_ATOMIC);
+	cfg80211_rx_mgmt(vif->ndev, freq, 0,
+			 ev->data, dlen, GFP_ATOMIC);
 
 	return 0;
 }
diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h
index 9f46c62b1eee..c37d67add090 100644
--- a/include/linux/nl80211.h
+++ b/include/linux/nl80211.h
@@ -1203,6 +1203,10 @@ enum nl80211_commands {
  *	the list. This needs to be used when the driver advertises the
  *	capability to timeout the stations.
  *
+ * @NL80211_ATTR_RX_SIGNAL_DBM: signal strength in dBm (as a 32-bit int);
+ *	this attribute is (depending on the driver capabilities) added to
+ *	received frames indicated with %NL80211_CMD_FRAME.
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -1450,6 +1454,8 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_INACTIVITY_TIMEOUT,
 
+	NL80211_ATTR_RX_SIGNAL_DBM,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 804805827736..4682c35a92c4 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -3189,6 +3189,7 @@ void cfg80211_del_sta(struct net_device *dev, const u8 *mac_addr, gfp_t gfp);
  * cfg80211_rx_mgmt - notification of received, unprocessed management frame
  * @dev: network device
  * @freq: Frequency on which the frame was received in MHz
+ * @sig_dbm: signal strength in mBm, or 0 if unknown
  * @buf: Management frame (header + body)
  * @len: length of the frame data
  * @gfp: context flags
@@ -3201,8 +3202,8 @@ void cfg80211_del_sta(struct net_device *dev, const u8 *mac_addr, gfp_t gfp);
  * This function is called whenever an Action frame is received for a station
  * mode interface, but is not processed in kernel.
  */
-bool cfg80211_rx_mgmt(struct net_device *dev, int freq, const u8 *buf,
-		      size_t len, gfp_t gfp);
+bool cfg80211_rx_mgmt(struct net_device *dev, int freq, int sig_dbm,
+		      const u8 *buf, size_t len, gfp_t gfp);
 
 /**
  * cfg80211_mgmt_tx_status - notification of TX status for management frame
@@ -3315,6 +3316,7 @@ void cfg80211_probe_status(struct net_device *dev, const u8 *addr,
  * @frame: the frame
  * @len: length of the frame
  * @freq: frequency the frame was received on
+ * @sig_dbm: signal strength in mBm, or 0 if unknown
  * @gfp: allocation flags
  *
  * Use this function to report to userspace when a beacon was
@@ -3323,7 +3325,7 @@ void cfg80211_probe_status(struct net_device *dev, const u8 *addr,
  */
 void cfg80211_report_obss_beacon(struct wiphy *wiphy,
 				 const u8 *frame, size_t len,
-				 int freq, gfp_t gfp);
+				 int freq, int sig_dbm, gfp_t gfp);
 
 /*
  * cfg80211_can_beacon_sec_chan - test if ht40 on extension channel can be used
diff --git a/net/mac80211/rx.c b/net/mac80211/rx.c
index 10bbbd33b314..5f6e32ca0858 100644
--- a/net/mac80211/rx.c
+++ b/net/mac80211/rx.c
@@ -2188,9 +2188,14 @@ ieee80211_rx_h_mgmt_check(struct ieee80211_rx_data *rx)
 	if (rx->sdata->vif.type == NL80211_IFTYPE_AP &&
 	    ieee80211_is_beacon(mgmt->frame_control) &&
 	    !(rx->flags & IEEE80211_RX_BEACON_REPORTED)) {
+		int sig = 0;
+
+		if (rx->local->hw.flags & IEEE80211_HW_SIGNAL_DBM)
+			sig = status->signal;
+
 		cfg80211_report_obss_beacon(rx->local->hw.wiphy,
 					    rx->skb->data, rx->skb->len,
-					    status->freq, GFP_ATOMIC);
+					    status->freq, sig, GFP_ATOMIC);
 		rx->flags |= IEEE80211_RX_BEACON_REPORTED;
 	}
 
@@ -2414,6 +2419,7 @@ static ieee80211_rx_result debug_noinline
 ieee80211_rx_h_userspace_mgmt(struct ieee80211_rx_data *rx)
 {
 	struct ieee80211_rx_status *status = IEEE80211_SKB_RXCB(rx->skb);
+	int sig = 0;
 
 	/* skip known-bad action frames and return them in the next handler */
 	if (status->rx_flags & IEEE80211_RX_MALFORMED_ACTION_FRM)
@@ -2426,7 +2432,10 @@ ieee80211_rx_h_userspace_mgmt(struct ieee80211_rx_data *rx)
 	 * it transmitted were processed or returned.
 	 */
 
-	if (cfg80211_rx_mgmt(rx->sdata->dev, status->freq,
+	if (rx->local->hw.flags & IEEE80211_HW_SIGNAL_DBM)
+		sig = status->signal;
+
+	if (cfg80211_rx_mgmt(rx->sdata->dev, status->freq, sig,
 			     rx->skb->data, rx->skb->len,
 			     GFP_ATOMIC)) {
 		if (rx->sta)
diff --git a/net/wireless/mlme.c b/net/wireless/mlme.c
index fb1e72179117..f5a7ac3a0939 100644
--- a/net/wireless/mlme.c
+++ b/net/wireless/mlme.c
@@ -814,8 +814,8 @@ int cfg80211_mlme_mgmt_tx(struct cfg80211_registered_device *rdev,
 				  cookie);
 }
 
-bool cfg80211_rx_mgmt(struct net_device *dev, int freq, const u8 *buf,
-		      size_t len, gfp_t gfp)
+bool cfg80211_rx_mgmt(struct net_device *dev, int freq, int sig_mbm,
+		      const u8 *buf, size_t len, gfp_t gfp)
 {
 	struct wireless_dev *wdev = dev->ieee80211_ptr;
 	struct wiphy *wiphy = wdev->wiphy;
@@ -854,7 +854,8 @@ bool cfg80211_rx_mgmt(struct net_device *dev, int freq, const u8 *buf,
 		/* found match! */
 
 		/* Indicate the received Action frame to user space */
-		if (nl80211_send_mgmt(rdev, dev, reg->nlpid, freq,
+		if (nl80211_send_mgmt(rdev, dev, reg->nlpid,
+				      freq, sig_mbm,
 				      buf, len, gfp))
 			continue;
 
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index 4b6afc338aac..39dbdf2adb12 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -7686,7 +7686,8 @@ bool nl80211_unexpected_4addr_frame(struct net_device *dev,
 
 int nl80211_send_mgmt(struct cfg80211_registered_device *rdev,
 		      struct net_device *netdev, u32 nlpid,
-		      int freq, const u8 *buf, size_t len, gfp_t gfp)
+		      int freq, int sig_dbm,
+		      const u8 *buf, size_t len, gfp_t gfp)
 {
 	struct sk_buff *msg;
 	void *hdr;
@@ -7704,6 +7705,8 @@ int nl80211_send_mgmt(struct cfg80211_registered_device *rdev,
 	NLA_PUT_U32(msg, NL80211_ATTR_WIPHY, rdev->wiphy_idx);
 	NLA_PUT_U32(msg, NL80211_ATTR_IFINDEX, netdev->ifindex);
 	NLA_PUT_U32(msg, NL80211_ATTR_WIPHY_FREQ, freq);
+	if (sig_dbm)
+		NLA_PUT_U32(msg, NL80211_ATTR_RX_SIGNAL_DBM, sig_dbm);
 	NLA_PUT(msg, NL80211_ATTR_FRAME, len, buf);
 
 	genlmsg_end(msg, hdr);
@@ -7965,7 +7968,7 @@ EXPORT_SYMBOL(cfg80211_probe_status);
 
 void cfg80211_report_obss_beacon(struct wiphy *wiphy,
 				 const u8 *frame, size_t len,
-				 int freq, gfp_t gfp)
+				 int freq, int sig_dbm, gfp_t gfp)
 {
 	struct cfg80211_registered_device *rdev = wiphy_to_dev(wiphy);
 	struct sk_buff *msg;
@@ -7988,6 +7991,8 @@ void cfg80211_report_obss_beacon(struct wiphy *wiphy,
 	NLA_PUT_U32(msg, NL80211_ATTR_WIPHY, rdev->wiphy_idx);
 	if (freq)
 		NLA_PUT_U32(msg, NL80211_ATTR_WIPHY_FREQ, freq);
+	if (sig_dbm)
+		NLA_PUT_U32(msg, NL80211_ATTR_RX_SIGNAL_DBM, sig_dbm);
 	NLA_PUT(msg, NL80211_ATTR_FRAME, len, frame);
 
 	genlmsg_end(msg, hdr);
diff --git a/net/wireless/nl80211.h b/net/wireless/nl80211.h
index 12bf4d185abe..4ffe50df9f31 100644
--- a/net/wireless/nl80211.h
+++ b/net/wireless/nl80211.h
@@ -92,7 +92,8 @@ void nl80211_send_sta_del_event(struct cfg80211_registered_device *rdev,
 				gfp_t gfp);
 
 int nl80211_send_mgmt(struct cfg80211_registered_device *rdev,
-		      struct net_device *netdev, u32 nlpid, int freq,
+		      struct net_device *netdev, u32 nlpid,
+		      int freq, int sig_dbm,
 		      const u8 *buf, size_t len, gfp_t gfp);
 void nl80211_send_mgmt_tx_status(struct cfg80211_registered_device *rdev,
 				 struct net_device *netdev, u64 cookie,
-- 
cgit v1.2.3


From 10d8493cd9efd38b1947b7a74276dbdc8311aa1a Mon Sep 17 00:00:00 2001
From: Arend van Spriel <arend@broadcom.com>
Date: Tue, 6 Mar 2012 15:50:48 +0100
Subject: bcma: add support for on-chip OTP memory used for SPROM storage

Wireless Broadcom chips can have either their SPROM data stored
on either external SPROM or on-chip OTP memory. Both are accessed
through the same register space. This patch adds support for the
on-chip OTP memory.

Tested with:
BCM43224 OTP and SPROM
BCM4331 SPROM
BCM4313 OTP

This patch is in response to linux-wireless thread [1].

[1] http://article.gmane.org/gmane.linux.kernel.wireless.general/85426

Tested-by: Saul St. John <saul.stjohn@gmail.com>
Tested-by: Rafal Milecki <zajec5@gmail.com>
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/bcma/sprom.c                        | 126 +++++++++++++++++++++++-----
 include/linux/bcma/bcma_driver_chipcommon.h |  10 ++-
 2 files changed, 115 insertions(+), 21 deletions(-)

(limited to 'include/linux')

diff --git a/drivers/bcma/sprom.c b/drivers/bcma/sprom.c
index fba8066857d2..cdcf75c0954f 100644
--- a/drivers/bcma/sprom.c
+++ b/drivers/bcma/sprom.c
@@ -300,37 +300,128 @@ static void bcma_sprom_extract_r8(struct bcma_bus *bus, const u16 *sprom)
 	     SSB_SROM8_FEM_ANTSWLUT_SHIFT);
 }
 
-static bool bcma_is_sprom_available(struct bcma_bus *bus)
+/*
+ * Indicates the presence of external SPROM.
+ */
+static bool bcma_sprom_ext_available(struct bcma_bus *bus)
 {
-	u32 sromctrl;
+	u32 chip_status;
+	u32 srom_control;
+	u32 present_mask;
 
-	if (!(bus->drv_cc.capabilities & BCMA_CC_CAP_SPROM))
-		return false;
+	if (bus->drv_cc.core->id.rev >= 31) {
+		if (!(bus->drv_cc.capabilities & BCMA_CC_CAP_SPROM))
+			return false;
 
-	if (bus->drv_cc.core->id.rev >= 32) {
-		sromctrl = bcma_read32(bus->drv_cc.core, BCMA_CC_SROM_CONTROL);
-		return sromctrl & BCMA_CC_SROM_CONTROL_PRESENT;
+		srom_control = bcma_read32(bus->drv_cc.core,
+					   BCMA_CC_SROM_CONTROL);
+		return srom_control & BCMA_CC_SROM_CONTROL_PRESENT;
 	}
-	return true;
+
+	/* older chipcommon revisions use chip status register */
+	chip_status = bcma_read32(bus->drv_cc.core, BCMA_CC_CHIPSTAT);
+	switch (bus->chipinfo.id) {
+	case 0x4313:
+		present_mask = BCMA_CC_CHIPST_4313_SPROM_PRESENT;
+		break;
+
+	case 0x4331:
+		present_mask = BCMA_CC_CHIPST_4331_SPROM_PRESENT;
+		break;
+
+	default:
+		return true;
+	}
+
+	return chip_status & present_mask;
+}
+
+/*
+ * Indicates that on-chip OTP memory is present and enabled.
+ */
+static bool bcma_sprom_onchip_available(struct bcma_bus *bus)
+{
+	u32 chip_status;
+	u32 otpsize = 0;
+	bool present;
+
+	chip_status = bcma_read32(bus->drv_cc.core, BCMA_CC_CHIPSTAT);
+	switch (bus->chipinfo.id) {
+	case 0x4313:
+		present = chip_status & BCMA_CC_CHIPST_4313_OTP_PRESENT;
+		break;
+
+	case 0x4331:
+		present = chip_status & BCMA_CC_CHIPST_4331_OTP_PRESENT;
+		break;
+
+	case 43224:
+	case 43225:
+		/* for these chips OTP is always available */
+		present = true;
+		break;
+
+	default:
+		present = false;
+		break;
+	}
+
+	if (present) {
+		otpsize = bus->drv_cc.capabilities & BCMA_CC_CAP_OTPS;
+		otpsize >>= BCMA_CC_CAP_OTPS_SHIFT;
+	}
+
+	return otpsize != 0;
+}
+
+/*
+ * Verify OTP is filled and determine the byte
+ * offset where SPROM data is located.
+ *
+ * On error, returns 0; byte offset otherwise.
+ */
+static int bcma_sprom_onchip_offset(struct bcma_bus *bus)
+{
+	struct bcma_device *cc = bus->drv_cc.core;
+	u32 offset;
+
+	/* verify OTP status */
+	if ((bcma_read32(cc, BCMA_CC_OTPS) & BCMA_CC_OTPS_GU_PROG_HW) == 0)
+		return 0;
+
+	/* obtain bit offset from otplayout register */
+	offset = (bcma_read32(cc, BCMA_CC_OTPL) & BCMA_CC_OTPL_GURGN_OFFSET);
+	return BCMA_CC_SPROM + (offset >> 3);
 }
 
 int bcma_sprom_get(struct bcma_bus *bus)
 {
-	u16 offset;
+	u16 offset = BCMA_CC_SPROM;
 	u16 *sprom;
 	int err = 0;
 
 	if (!bus->drv_cc.core)
 		return -EOPNOTSUPP;
 
-	if (!bcma_is_sprom_available(bus)) {
+	if (!bcma_sprom_ext_available(bus)) {
 		/*
-		 * Maybe there is no SPROM on the device?
-		 * Now we ask the arch code if there is some sprom
-		 * available for this device in some other storage.
+		 * External SPROM takes precedence so check
+		 * on-chip OTP only when no external SPROM
+		 * is present.
 		 */
-		err = bcma_fill_sprom_with_fallback(bus, &bus->sprom);
-		return err;
+		if (bcma_sprom_onchip_available(bus)) {
+			/* determine offset */
+			offset = bcma_sprom_onchip_offset(bus);
+		}
+		if (!offset) {
+			/*
+			 * Maybe there is no SPROM on the device?
+			 * Now we ask the arch code if there is some sprom
+			 * available for this device in some other storage.
+			 */
+			err = bcma_fill_sprom_with_fallback(bus, &bus->sprom);
+			return err;
+		}
 	}
 
 	sprom = kcalloc(SSB_SPROMSIZE_WORDS_R4, sizeof(u16),
@@ -341,11 +432,6 @@ int bcma_sprom_get(struct bcma_bus *bus)
 	if (bus->chipinfo.id == 0x4331)
 		bcma_chipco_bcm4331_ext_pa_lines_ctl(&bus->drv_cc, false);
 
-	/* Most cards have SPROM moved by additional offset 0x30 (48 dwords).
-	 * According to brcm80211 this applies to cards with PCIe rev >= 6
-	 * TODO: understand this condition and use it */
-	offset = (bus->chipinfo.id == 0x4331) ? BCMA_CC_SPROM :
-		BCMA_CC_SPROM_PCIE6;
 	pr_debug("SPROM offset 0x%x\n", offset);
 	bcma_sprom_read(bus, offset, sprom);
 
diff --git a/include/linux/bcma/bcma_driver_chipcommon.h b/include/linux/bcma/bcma_driver_chipcommon.h
index e72938b10714..8bbfe31fbac8 100644
--- a/include/linux/bcma/bcma_driver_chipcommon.h
+++ b/include/linux/bcma/bcma_driver_chipcommon.h
@@ -56,6 +56,9 @@
 #define	 BCMA_CC_OTPS_HW_PROTECT	0x00000001
 #define	 BCMA_CC_OTPS_SW_PROTECT	0x00000002
 #define	 BCMA_CC_OTPS_CID_PROTECT	0x00000004
+#define  BCMA_CC_OTPS_GU_PROG_IND	0x00000F00	/* General Use programmed indication */
+#define  BCMA_CC_OTPS_GU_PROG_IND_SHIFT	8
+#define  BCMA_CC_OTPS_GU_PROG_HW	0x00000100	/* HW region programmed */
 #define BCMA_CC_OTPC			0x0014		/* OTP control */
 #define	 BCMA_CC_OTPC_RECWAIT		0xFF000000
 #define	 BCMA_CC_OTPC_PROGWAIT		0x00FFFF00
@@ -72,6 +75,8 @@
 #define	 BCMA_CC_OTPP_READ		0x40000000
 #define	 BCMA_CC_OTPP_START		0x80000000
 #define	 BCMA_CC_OTPP_BUSY		0x80000000
+#define BCMA_CC_OTPL			0x001C		/* OTP layout */
+#define  BCMA_CC_OTPL_GURGN_OFFSET	0x00000FFF	/* offset of general use region */
 #define BCMA_CC_IRQSTAT			0x0020
 #define BCMA_CC_IRQMASK			0x0024
 #define	 BCMA_CC_IRQ_GPIO		0x00000001	/* gpio intr */
@@ -79,6 +84,10 @@
 #define	 BCMA_CC_IRQ_WDRESET		0x80000000	/* watchdog reset occurred */
 #define BCMA_CC_CHIPCTL			0x0028		/* Rev >= 11 only */
 #define BCMA_CC_CHIPSTAT		0x002C		/* Rev >= 11 only */
+#define  BCMA_CC_CHIPST_4313_SPROM_PRESENT	1
+#define  BCMA_CC_CHIPST_4313_OTP_PRESENT	2
+#define  BCMA_CC_CHIPST_4331_SPROM_PRESENT	2
+#define  BCMA_CC_CHIPST_4331_OTP_PRESENT	4
 #define BCMA_CC_JCMD			0x0030		/* Rev >= 10 only */
 #define  BCMA_CC_JCMD_START		0x80000000
 #define  BCMA_CC_JCMD_BUSY		0x80000000
@@ -256,7 +265,6 @@
 #define BCMA_CC_PLLCTL_ADDR		0x0660
 #define BCMA_CC_PLLCTL_DATA		0x0664
 #define BCMA_CC_SPROM			0x0800 /* SPROM beginning */
-#define BCMA_CC_SPROM_PCIE6		0x0830 /* SPROM beginning on PCIe rev >= 6 */
 
 /* Divider allocation in 4716/47162/5356 */
 #define BCMA_CC_PMU5_MAINPLL_CPU	1
-- 
cgit v1.2.3


From c970a1ac4e75a5d31c7b6e8e9f0bb192b0a511e7 Mon Sep 17 00:00:00 2001
From: Samuel Ortiz <sameo@linux.intel.com>
Date: Mon, 5 Mar 2012 01:03:34 +0100
Subject: NFC: Add device powered netlink attribute

For user space to know if a device is up or down.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 include/linux/nfc.h | 1 +
 net/nfc/netlink.c   | 3 +++
 2 files changed, 4 insertions(+)

(limited to 'include/linux')

diff --git a/include/linux/nfc.h b/include/linux/nfc.h
index b4999abcb2a2..39c1fcf089c0 100644
--- a/include/linux/nfc.h
+++ b/include/linux/nfc.h
@@ -107,6 +107,7 @@ enum nfc_attrs {
 	NFC_ATTR_TARGET_SENSF_RES,
 	NFC_ATTR_COMM_MODE,
 	NFC_ATTR_RF_MODE,
+	NFC_ATTR_DEVICE_POWERED,
 /* private: internal use only */
 	__NFC_ATTR_AFTER_LAST
 };
diff --git a/net/nfc/netlink.c b/net/nfc/netlink.c
index 07f0348aabf5..a1388e4efd6f 100644
--- a/net/nfc/netlink.c
+++ b/net/nfc/netlink.c
@@ -48,6 +48,7 @@ static const struct nla_policy nfc_genl_policy[NFC_ATTR_MAX + 1] = {
 	[NFC_ATTR_PROTOCOLS] = { .type = NLA_U32 },
 	[NFC_ATTR_COMM_MODE] = { .type = NLA_U8 },
 	[NFC_ATTR_RF_MODE] = { .type = NLA_U8 },
+	[NFC_ATTR_DEVICE_POWERED] = { .type = NLA_U8 },
 };
 
 static int nfc_genl_send_target(struct sk_buff *msg, struct nfc_target *target,
@@ -200,6 +201,7 @@ int nfc_genl_device_added(struct nfc_dev *dev)
 	NLA_PUT_STRING(msg, NFC_ATTR_DEVICE_NAME, nfc_device_name(dev));
 	NLA_PUT_U32(msg, NFC_ATTR_DEVICE_INDEX, dev->idx);
 	NLA_PUT_U32(msg, NFC_ATTR_PROTOCOLS, dev->supported_protocols);
+	NLA_PUT_U8(msg, NFC_ATTR_DEVICE_POWERED, dev->dev_up);
 
 	genlmsg_end(msg, hdr);
 
@@ -261,6 +263,7 @@ static int nfc_genl_send_device(struct sk_buff *msg, struct nfc_dev *dev,
 	NLA_PUT_STRING(msg, NFC_ATTR_DEVICE_NAME, nfc_device_name(dev));
 	NLA_PUT_U32(msg, NFC_ATTR_DEVICE_INDEX, dev->idx);
 	NLA_PUT_U32(msg, NFC_ATTR_PROTOCOLS, dev->supported_protocols);
+	NLA_PUT_U8(msg, NFC_ATTR_DEVICE_POWERED, dev->dev_up);
 
 	return genlmsg_end(msg, hdr);
 
-- 
cgit v1.2.3


From 4486ea987efdaa546bdda569e3dfacdc14a9fb13 Mon Sep 17 00:00:00 2001
From: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Date: Wed, 7 Mar 2012 17:27:12 +0530
Subject: cfg80211: Add background scan period attribute.

Receive background scan period as part of connect
command and pass the same to the driver.

Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 include/linux/nl80211.h | 10 ++++++++++
 include/net/cfg80211.h  |  3 +++
 net/wireless/nl80211.c  |  8 ++++++++
 net/wireless/wext-sme.c |  3 +++
 4 files changed, 24 insertions(+)

(limited to 'include/linux')

diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h
index c37d67add090..e474f6e780cc 100644
--- a/include/linux/nl80211.h
+++ b/include/linux/nl80211.h
@@ -369,6 +369,11 @@
  *	%NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
  *	%NL80211_ATTR_CONTROL_PORT_ETHERTYPE and
  *	%NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT.
+ *	Background scan period can optionally be
+ *	specified in %NL80211_ATTR_BG_SCAN_PERIOD,
+ *	if not specified default background scan configuration
+ *	in driver is used and if period value is 0, bg scan will be disabled.
+ *	This attribute is ignored if driver does not support roam scan.
  *	It is also sent as an event, with the BSSID and response IEs when the
  *	connection is established or failed to be established. This can be
  *	determined by the STATUS_CODE attribute.
@@ -1207,6 +1212,9 @@ enum nl80211_commands {
  *	this attribute is (depending on the driver capabilities) added to
  *	received frames indicated with %NL80211_CMD_FRAME.
  *
+ * @NL80211_ATTR_BG_SCAN_PERIOD: Background scan period in seconds
+ *      or 0 to disable background scan.
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -1456,6 +1464,8 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_RX_SIGNAL_DBM,
 
+	NL80211_ATTR_BG_SCAN_PERIOD,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 57c9fddc2acf..66f460325e24 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -1203,6 +1203,8 @@ struct cfg80211_ibss_params {
  * @key_idx: index of WEP key for shared key authentication
  * @key: WEP key for shared key authentication
  * @flags:  See &enum cfg80211_assoc_req_flags
+ * @bg_scan_period:  Background scan period in seconds
+ *   or -1 to indicate that default value is to be used.
  * @ht_capa:  HT Capabilities over-rides.  Values set in ht_capa_mask
  *   will be used in ht_capa.  Un-supported values will be ignored.
  * @ht_capa_mask:  The bits of ht_capa which are to be used.
@@ -1220,6 +1222,7 @@ struct cfg80211_connect_params {
 	const u8 *key;
 	u8 key_len, key_idx;
 	u32 flags;
+	int bg_scan_period;
 	struct ieee80211_ht_cap ht_capa;
 	struct ieee80211_ht_cap ht_capa_mask;
 };
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index 39dbdf2adb12..4c1eb9472ddb 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -205,6 +205,7 @@ static const struct nla_policy nl80211_policy[NL80211_ATTR_MAX+1] = {
 	},
 	[NL80211_ATTR_NOACK_MAP] = { .type = NLA_U16 },
 	[NL80211_ATTR_INACTIVITY_TIMEOUT] = { .type = NLA_U16 },
+	[NL80211_ATTR_BG_SCAN_PERIOD] = { .type = NLA_U16 },
 };
 
 /* policy for the key attributes */
@@ -5116,6 +5117,13 @@ static int nl80211_connect(struct sk_buff *skb, struct genl_info *info)
 
 	wiphy = &rdev->wiphy;
 
+	connect.bg_scan_period = -1;
+	if (info->attrs[NL80211_ATTR_BG_SCAN_PERIOD] &&
+		(wiphy->flags & WIPHY_FLAG_SUPPORTS_FW_ROAM)) {
+		connect.bg_scan_period =
+			nla_get_u16(info->attrs[NL80211_ATTR_BG_SCAN_PERIOD]);
+	}
+
 	if (info->attrs[NL80211_ATTR_MAC])
 		connect.bssid = nla_data(info->attrs[NL80211_ATTR_MAC]);
 	connect.ssid = nla_data(info->attrs[NL80211_ATTR_SSID]);
diff --git a/net/wireless/wext-sme.c b/net/wireless/wext-sme.c
index 326750b99151..7c01c2f3b6cf 100644
--- a/net/wireless/wext-sme.c
+++ b/net/wireless/wext-sme.c
@@ -30,6 +30,9 @@ int cfg80211_mgd_wext_connect(struct cfg80211_registered_device *rdev,
 	wdev->wext.connect.ie = wdev->wext.ie;
 	wdev->wext.connect.ie_len = wdev->wext.ie_len;
 
+	/* Use default background scan period */
+	wdev->wext.connect.bg_scan_period = -1;
+
 	if (wdev->wext.keys) {
 		wdev->wext.keys->def = wdev->wext.default_key;
 		wdev->wext.keys->defmgmt = wdev->wext.default_mgmt_key;
-- 
cgit v1.2.3