From 51e0a01206613ad80a3841388ecfa46476dabdf5 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 20 Feb 2012 12:02:19 -0800 Subject: USB: Calculate USB 3.0 exit latencies for LPM. There are several different exit latencies associated with coming out of the U1 or U2 lower power link state. Device Exit Latency (DEL) is the maximum time it takes for the USB device to bring its upstream link into U0. That can be found in the SuperSpeed Extended Capabilities BOS descriptor for the device. The time it takes for a particular link in the tree to exit to U0 is the maximum of either the parent hub's U1/U2 DEL, or the child's U1/U2 DEL. Hubs introduce a further delay that effects how long it takes a child device to transition to U0. When a USB 3.0 hub receives a header packet, it takes some time to decode that header and figure out which downstream port the packet was destined for. If the port is not in U0, this hub header decode latency will cause an additional delay for bringing the child device to U0. This Hub Header Decode Latency is found in the USB 3.0 hub descriptor. We can use DEL and the header decode latency, along with additional latencies imposed by each additional hub tier, to figure out the exit latencies for both host-initiated and device-initiated exit to U0. The Max Exit Latency (MEL) is the worst-case time it will take for a host-initiated exit to U0, based on whether U1 or U2 link states are enabled. The ping or packet must traverse the path to the device, and each hub along the way incurs the hub header decode latency in order to figure out which device the transfer was bound for. We say worst-case, because some hubs may not be in the lowest link state that is enabled. See the examples in section C.2.2.1. Note that "HSD" is a "host specific delay" that the power appendix architect has not been able to tell me how to calculate. There's no way to get HSD from the xHCI registers either, so I'm simply ignoring it. The Path Exit Latency (PEL) is the worst-case time it will take for a device-initiate exit to U0 to place all the links from the device to the host into U0. The System Exit Latency (SEL) is another device-initiated exit latency. SEL is useful for USB 3.0 devices that need to send data to the host at specific intervals. The device may send an NRDY to indicate it isn't ready to send data, then put its link into a lower power state. If it needs to have that data transmitted at a specific time, it can use SEL to back calculate when it will need to bring the link back into U0 to meet its deadlines. SEL is the worst-case time from the device-initiated exit to U0, to when the device will receive a packet from the host controller. It includes PEL, the time it takes for an ERDY to get to the host, a host-specific delay for the host to process that ERDY, and the time it takes for the packet to traverse the path to the device. See Figure C-2 in the USB 3.0 bus specification. Note: I have not been able to get good answers about what the host-specific delay to process the ERDY should be. The Intel HW developers say it will be specific to the platform the xHCI host is integrated into, and they say it's negligible. Ignore this too. Separate from these four exit latencies are the U1/U2 timeout values we program into the parent hubs. These timeouts tell the hub to attempt to place the device into a lower power link state after the link has been idle for that amount of time. Create two arrays (one for U1 and one for U2) to store mel, pel, sel, and the timeout values. Store the exit latency values in nanosecond units, since that's the smallest units used (DEL is in us, but the Hub Header Decode Latency is in ns). If a USB 3.0 device doesn't have a SuperSpeed Extended Capabilities BOS descriptor, it's highly unlikely it will be able to handle LPM requests properly. So it's best to disable LPM for devices that don't have this descriptor, and any children beneath it, if it's a USB 3.0 hub. Warn users when that happens, since it means they have a non-compliant USB 3.0 device or hub. This patch assumes a simplified design where links deep in the tree will not have U1 or U2 enabled unless all their parent links have the corresponding LPM state enabled. Eventually, we might want to allow a different policy, and we can revisit this patch when that happens. Signed-off-by: Sarah Sharp Cc: Alan Stern --- include/linux/usb.h | 37 +++++++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+) (limited to 'include/linux/usb.h') diff --git a/include/linux/usb.h b/include/linux/usb.h index 14933451d21d..e6c815590fdd 100644 --- a/include/linux/usb.h +++ b/include/linux/usb.h @@ -378,6 +378,39 @@ enum usb_device_removable { USB_DEVICE_FIXED, }; +/* + * USB 3.0 Link Power Management (LPM) parameters. + * + * PEL and SEL are USB 3.0 Link PM latencies for device-initiated LPM exit. + * MEL is the USB 3.0 Link PM latency for host-initiated LPM exit. + * All three are stored in nanoseconds. + */ +struct usb3_lpm_parameters { + /* + * Maximum exit latency (MEL) for the host to send a packet to the + * device (either a Ping for isoc endpoints, or a data packet for + * interrupt endpoints), the hubs to decode the packet, and for all hubs + * in the path to transition the links to U0. + */ + unsigned int mel; + /* + * Maximum exit latency for a device-initiated LPM transition to bring + * all links into U0. Abbreviated as "PEL" in section 9.4.12 of the USB + * 3.0 spec, with no explanation of what "P" stands for. "Path"? + */ + unsigned int pel; + + /* + * The System Exit Latency (SEL) includes PEL, and three other + * latencies. After a device initiates a U0 transition, it will take + * some time from when the device sends the ERDY to when it will finally + * receive the data packet. Basically, SEL should be the worse-case + * latency from when a device starts initiating a U0 transition to when + * it will get data. + */ + unsigned int sel; +}; + /** * struct usb_device - kernel's representation of a USB device * @devnum: device number; address on a USB bus @@ -435,6 +468,8 @@ enum usb_device_removable { * specific data for the device. * @slot_id: Slot ID assigned by xHCI * @removable: Device can be physically removed from this port + * @u1_params: exit latencies for U1 (USB 3.0 LPM). + * @u2_params: exit latencies for U2 (USB 3.0 LPM). * * Notes: * Usbcore drivers should not set usbdev->state directly. Instead use @@ -507,6 +542,8 @@ struct usb_device { struct wusb_dev *wusb_dev; int slot_id; enum usb_device_removable removable; + struct usb3_lpm_parameters u1_params; + struct usb3_lpm_parameters u2_params; }; #define to_usb_device(d) container_of(d, struct usb_device, dev) -- cgit v1.2.3 From 8afa408cba5c474696df6307a64b1c612bbcadbc Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 23 Apr 2012 10:08:51 -0700 Subject: USB: Allow drivers to disable hub-initiated LPM. USB 3.0 Link Power Management (LPM) is designed to allow individual links in the bus to go into lower power states. There are two ways a link can enter a lower power state: 1. Device-initiated LPM. When a USB device decides it can go into a lower power link state, it sends a message to the parent hub, telling it to go into either U1 or U2. Device-initiated LPM is good for devices that send data to the host, like communications devices. 2. Hub-initiated LPM. After the link has been idle for a specific amount of time, the parent hub will request that the child go into a lower power state. The child can refuse that request. For example, a USB modem may want to refuse the LPM request if it is in the middle of receiving a text message. Hub-initiated LPM is good for devices where only the host initiates the data transfer, like USB printers or USB mass storage devices. Links will be automatically placed into higher power states by the USB hubs and roothubs whenever the host starts a USB transmission. Introduce a new usb_driver flag, disable_hub_initiated_lpm, that allows drivers to disable hub-initiated LPM. Signed-off-by: Sarah Sharp Cc: Marcel Holtmann Cc: Gustavo Padovan Cc: Johan Hedberg Cc: Hansjoerg Lipp Cc: Tilman Schmidt Cc: Karsten Keil Cc: Oliver Neukum Cc: Peter Korsgaard Cc: Jan Dumon Cc: Petko Manolov Cc: Steve Glendinning Cc: "John W. Linville" Cc: Kalle Valo Cc: "Luis R. Rodriguez" Cc: Jouni Malinen Cc: Vasanthakumar Thiagarajan Cc: Senthil Balasubramanian Cc: Christian Lamparter Cc: Brett Rudley Cc: Roland Vossen Cc: Arend van Spriel Cc: "Franky (Zhenhui) Lin" Cc: Kan Yan Cc: Dan Williams Cc: Jussi Kivilinna Cc: Ivo van Doorn Cc: Gertjan van Wingerde Cc: Helmut Schaa Cc: Herton Ronaldo Krzesinski Cc: Hin-Tak Leung Cc: Larry Finger Cc: Chaoming Li Cc: Daniel Drake Cc: Ulrich Kunitz Cc: linux-bluetooth@vger.kernel.org Cc: gigaset307x-common@lists.sourceforge.net Cc: netdev@vger.kernel.org Cc: linux-usb@vger.kernel.org Cc: linux-wireless@vger.kernel.org Cc: ath9k-devel@lists.ath9k.org Cc: libertas-dev@lists.infradead.org Cc: users@rt2x00.serialmonkey.com --- include/linux/usb.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'include/linux/usb.h') diff --git a/include/linux/usb.h b/include/linux/usb.h index e6c815590fdd..22e7b53123ef 100644 --- a/include/linux/usb.h +++ b/include/linux/usb.h @@ -879,6 +879,9 @@ struct usbdrv_wrap { * for interfaces bound to this driver. * @soft_unbind: if set to 1, the USB core will not kill URBs and disable * endpoints before calling the driver's disconnect method. + * @disable_hub_initiated_lpm: if set to 0, the USB core will not allow hubs + * to initiate lower power link state transitions when an idle timeout + * occurs. Device-initiated USB 3.0 link PM will still be allowed. * * USB interface drivers must provide a name, probe() and disconnect() * methods, and an id_table. Other driver fields are optional. @@ -919,6 +922,7 @@ struct usb_driver { struct usbdrv_wrap drvwrap; unsigned int no_dynamic_id:1; unsigned int supports_autosuspend:1; + unsigned int disable_hub_initiated_lpm:1; unsigned int soft_unbind:1; }; #define to_usb_driver(d) container_of(d, struct usb_driver, drvwrap.driver) -- cgit v1.2.3 From 1ea7e0e8e3d0f50901d335ea4178ab2aa8c88201 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 24 Apr 2012 17:21:50 -0700 Subject: USB: Add support to enable/disable USB3 link states. There are various functions within the USB core that will need to disable USB 3.0 link power states. For example, when a USB device driver is being bound to an interface, we need to disable USB 3.0 LPM until we know if the driver will allow hub-initiated LPM transitions. Another example is when the USB core is switching alternate interface settings. The USB 3.0 timeout values are dependent on what endpoints are enabled, so we want to ensure that LPM is disabled until the new alt setting is fully installed. Multiple functions need to disable LPM, and those functions can even be nested. For example, usb_bind_interface() could disable LPM, and then call into the driver probe function, which may attempt to switch to a different alt setting. Therefore, we need to keep a count of the number of functions that require LPM to be disabled at any point in time. Introduce two new USB core API calls, usb_disable_lpm() and usb_enable_lpm(). These functions increment and decrement a new variable in the usb_device, lpm_disable_count. If usb_disable_lpm() fails, it will call usb_enable_lpm() in order to balance the lpm_disable_count. These two new functions must be called with the bandwidth_mutex locked. If the bandwidth_mutex is not already held by the caller, it should instead call usb_unlocked_disable_lpm() and usb_enable_lpm(), which take the bandwidth_mutex before calling usb_disable_lpm() and usb_enable_lpm(), respectively. Introduce a new variable (timeout) in the usb3_lpm_params structure to keep track of the currently enabled U1/U2 timeout values. When usb_disable_lpm() is called, and the USB device has the U1 or U2 timeouts set to a non-zero value (meaning either device-initiated or hub-initiated LPM is enabled), attempt to disable LPM, regardless of the state of the lpm_disable_count. We want to ensure that all callers can be guaranteed that LPM is disabled if usb_disable_lpm() returns zero. Otherwise the following scenario could occur: 1. Driver A is being bound to interface 1. usb_probe_interface() disables LPM. Driver A doesn't care if hub-initiated LPM is enabled, so even though usb_disable_lpm() fails, the probe of the driver continues, and the bandwidth mutex is dropped. 2. Meanwhile, Driver B is being bound to interface 2. usb_probe_interface() grabs the bandwidth mutex and calls usb_disable_lpm(). That call should attempt to disable LPM, even though the lpm_disable_count is set to 1 by Driver A. For usb_enable_lpm(), we attempt to enable LPM only when the lpm_disable_count is zero. If some step in enabling LPM fails, it will only have a minimal impact on power consumption, and all USB device drivers should still work properly. Therefore don't bother to return any error codes. Don't enable device-initiated LPM if the device is unconfigured. The USB device will only accept the U1/U2_ENABLE control transfers in the configured state. Do enable hub-initiated LPM in that case, since devices are allowed to accept the LGO_Ux link commands in any state. Don't enable or disable LPM if the device is marked as not being LPM capable. This can happen if: - the USB device doesn't have a SS BOS descriptor, - the device's parent hub has a zeroed bHeaderDecodeLatency value, or - the xHCI host doesn't support LPM. Signed-off-by: Sarah Sharp Cc: Andiry Xu Cc: Alan Stern Signed-off-by: Sarah Sharp --- drivers/usb/core/hub.c | 414 +++++++++++++++++++++++++++++++++++++++++++++++ include/linux/usb.h | 21 ++- include/linux/usb/ch11.h | 2 + include/linux/usb/ch9.h | 45 ++++++ include/linux/usb/hcd.h | 9 ++ 5 files changed, 489 insertions(+), 2 deletions(-) (limited to 'include/linux/usb.h') diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 5219507bf227..fd1ec481aec1 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -3050,11 +3050,425 @@ void usb_root_hub_lost_power(struct usb_device *rhdev) } EXPORT_SYMBOL_GPL(usb_root_hub_lost_power); +static const char * const usb3_lpm_names[] = { + "U0", + "U1", + "U2", + "U3", +}; + +/* + * Send a Set SEL control transfer to the device, prior to enabling + * device-initiated U1 or U2. This lets the device know the exit latencies from + * the time the device initiates a U1 or U2 exit, to the time it will receive a + * packet from the host. + * + * This function will fail if the SEL or PEL values for udev are greater than + * the maximum allowed values for the link state to be enabled. + */ +static int usb_req_set_sel(struct usb_device *udev, enum usb3_link_state state) +{ + struct usb_set_sel_req *sel_values; + unsigned long long u1_sel; + unsigned long long u1_pel; + unsigned long long u2_sel; + unsigned long long u2_pel; + int ret; + + /* Convert SEL and PEL stored in ns to us */ + u1_sel = DIV_ROUND_UP(udev->u1_params.sel, 1000); + u1_pel = DIV_ROUND_UP(udev->u1_params.pel, 1000); + u2_sel = DIV_ROUND_UP(udev->u2_params.sel, 1000); + u2_pel = DIV_ROUND_UP(udev->u2_params.pel, 1000); + + /* + * Make sure that the calculated SEL and PEL values for the link + * state we're enabling aren't bigger than the max SEL/PEL + * value that will fit in the SET SEL control transfer. + * Otherwise the device would get an incorrect idea of the exit + * latency for the link state, and could start a device-initiated + * U1/U2 when the exit latencies are too high. + */ + if ((state == USB3_LPM_U1 && + (u1_sel > USB3_LPM_MAX_U1_SEL_PEL || + u1_pel > USB3_LPM_MAX_U1_SEL_PEL)) || + (state == USB3_LPM_U2 && + (u2_sel > USB3_LPM_MAX_U2_SEL_PEL || + u2_pel > USB3_LPM_MAX_U2_SEL_PEL))) { + dev_dbg(&udev->dev, "Device-initiated %s disabled due " + "to long SEL %llu ms or PEL %llu ms\n", + usb3_lpm_names[state], u1_sel, u1_pel); + return -EINVAL; + } + + /* + * If we're enabling device-initiated LPM for one link state, + * but the other link state has a too high SEL or PEL value, + * just set those values to the max in the Set SEL request. + */ + if (u1_sel > USB3_LPM_MAX_U1_SEL_PEL) + u1_sel = USB3_LPM_MAX_U1_SEL_PEL; + + if (u1_pel > USB3_LPM_MAX_U1_SEL_PEL) + u1_pel = USB3_LPM_MAX_U1_SEL_PEL; + + if (u2_sel > USB3_LPM_MAX_U2_SEL_PEL) + u2_sel = USB3_LPM_MAX_U2_SEL_PEL; + + if (u2_pel > USB3_LPM_MAX_U2_SEL_PEL) + u2_pel = USB3_LPM_MAX_U2_SEL_PEL; + + /* + * usb_enable_lpm() can be called as part of a failed device reset, + * which may be initiated by an error path of a mass storage driver. + * Therefore, use GFP_NOIO. + */ + sel_values = kmalloc(sizeof *(sel_values), GFP_NOIO); + if (!sel_values) + return -ENOMEM; + + sel_values->u1_sel = u1_sel; + sel_values->u1_pel = u1_pel; + sel_values->u2_sel = cpu_to_le16(u2_sel); + sel_values->u2_pel = cpu_to_le16(u2_pel); + + ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), + USB_REQ_SET_SEL, + USB_RECIP_DEVICE, + 0, 0, + sel_values, sizeof *(sel_values), + USB_CTRL_SET_TIMEOUT); + kfree(sel_values); + return ret; +} + +/* + * Enable or disable device-initiated U1 or U2 transitions. + */ +static int usb_set_device_initiated_lpm(struct usb_device *udev, + enum usb3_link_state state, bool enable) +{ + int ret; + int feature; + + switch (state) { + case USB3_LPM_U1: + feature = USB_DEVICE_U1_ENABLE; + break; + case USB3_LPM_U2: + feature = USB_DEVICE_U2_ENABLE; + break; + default: + dev_warn(&udev->dev, "%s: Can't %s non-U1 or U2 state.\n", + __func__, enable ? "enable" : "disable"); + return -EINVAL; + } + + if (udev->state != USB_STATE_CONFIGURED) { + dev_dbg(&udev->dev, "%s: Can't %s %s state " + "for unconfigured device.\n", + __func__, enable ? "enable" : "disable", + usb3_lpm_names[state]); + return 0; + } + + if (enable) { + /* + * First, let the device know about the exit latencies + * associated with the link state we're about to enable. + */ + ret = usb_req_set_sel(udev, state); + if (ret < 0) { + dev_warn(&udev->dev, "Set SEL for device-initiated " + "%s failed.\n", usb3_lpm_names[state]); + return -EBUSY; + } + /* + * Now send the control transfer to enable device-initiated LPM + * for either U1 or U2. + */ + ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), + USB_REQ_SET_FEATURE, + USB_RECIP_DEVICE, + feature, + 0, NULL, 0, + USB_CTRL_SET_TIMEOUT); + } else { + ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), + USB_REQ_CLEAR_FEATURE, + USB_RECIP_DEVICE, + feature, + 0, NULL, 0, + USB_CTRL_SET_TIMEOUT); + } + if (ret < 0) { + dev_warn(&udev->dev, "%s of device-initiated %s failed.\n", + enable ? "Enable" : "Disable", + usb3_lpm_names[state]); + return -EBUSY; + } + return 0; +} + +static int usb_set_lpm_timeout(struct usb_device *udev, + enum usb3_link_state state, int timeout) +{ + int ret; + int feature; + + switch (state) { + case USB3_LPM_U1: + feature = USB_PORT_FEAT_U1_TIMEOUT; + break; + case USB3_LPM_U2: + feature = USB_PORT_FEAT_U2_TIMEOUT; + break; + default: + dev_warn(&udev->dev, "%s: Can't set timeout for non-U1 or U2 state.\n", + __func__); + return -EINVAL; + } + + if (state == USB3_LPM_U1 && timeout > USB3_LPM_U1_MAX_TIMEOUT && + timeout != USB3_LPM_DEVICE_INITIATED) { + dev_warn(&udev->dev, "Failed to set %s timeout to 0x%x, " + "which is a reserved value.\n", + usb3_lpm_names[state], timeout); + return -EINVAL; + } + + ret = set_port_feature(udev->parent, + USB_PORT_LPM_TIMEOUT(timeout) | udev->portnum, + feature); + if (ret < 0) { + dev_warn(&udev->dev, "Failed to set %s timeout to 0x%x," + "error code %i\n", usb3_lpm_names[state], + timeout, ret); + return -EBUSY; + } + if (state == USB3_LPM_U1) + udev->u1_params.timeout = timeout; + else + udev->u2_params.timeout = timeout; + return 0; +} + +/* + * Enable the hub-initiated U1/U2 idle timeouts, and enable device-initiated + * U1/U2 entry. + * + * We will attempt to enable U1 or U2, but there are no guarantees that the + * control transfers to set the hub timeout or enable device-initiated U1/U2 + * will be successful. + * + * If we cannot set the parent hub U1/U2 timeout, we attempt to let the xHCI + * driver know about it. If that call fails, it should be harmless, and just + * take up more slightly more bus bandwidth for unnecessary U1/U2 exit latency. + */ +static void usb_enable_link_state(struct usb_hcd *hcd, struct usb_device *udev, + enum usb3_link_state state) +{ + int timeout; + + /* We allow the host controller to set the U1/U2 timeout internally + * first, so that it can change its schedule to account for the + * additional latency to send data to a device in a lower power + * link state. + */ + timeout = hcd->driver->enable_usb3_lpm_timeout(hcd, udev, state); + + /* xHCI host controller doesn't want to enable this LPM state. */ + if (timeout == 0) + return; + + if (timeout < 0) { + dev_warn(&udev->dev, "Could not enable %s link state, " + "xHCI error %i.\n", usb3_lpm_names[state], + timeout); + return; + } + + if (usb_set_lpm_timeout(udev, state, timeout)) + /* If we can't set the parent hub U1/U2 timeout, + * device-initiated LPM won't be allowed either, so let the xHCI + * host know that this link state won't be enabled. + */ + hcd->driver->disable_usb3_lpm_timeout(hcd, udev, state); + + /* Only a configured device will accept the Set Feature U1/U2_ENABLE */ + else if (udev->actconfig) + usb_set_device_initiated_lpm(udev, state, true); + +} + +/* + * Disable the hub-initiated U1/U2 idle timeouts, and disable device-initiated + * U1/U2 entry. + * + * If this function returns -EBUSY, the parent hub will still allow U1/U2 entry. + * If zero is returned, the parent will not allow the link to go into U1/U2. + * + * If zero is returned, device-initiated U1/U2 entry may still be enabled, but + * it won't have an effect on the bus link state because the parent hub will + * still disallow device-initiated U1/U2 entry. + * + * If zero is returned, the xHCI host controller may still think U1/U2 entry is + * possible. The result will be slightly more bus bandwidth will be taken up + * (to account for U1/U2 exit latency), but it should be harmless. + */ +static int usb_disable_link_state(struct usb_hcd *hcd, struct usb_device *udev, + enum usb3_link_state state) +{ + int feature; + + switch (state) { + case USB3_LPM_U1: + feature = USB_PORT_FEAT_U1_TIMEOUT; + break; + case USB3_LPM_U2: + feature = USB_PORT_FEAT_U2_TIMEOUT; + break; + default: + dev_warn(&udev->dev, "%s: Can't disable non-U1 or U2 state.\n", + __func__); + return -EINVAL; + } + + if (usb_set_lpm_timeout(udev, state, 0)) + return -EBUSY; + + usb_set_device_initiated_lpm(udev, state, false); + + if (hcd->driver->disable_usb3_lpm_timeout(hcd, udev, state)) + dev_warn(&udev->dev, "Could not disable xHCI %s timeout, " + "bus schedule bandwidth may be impacted.\n", + usb3_lpm_names[state]); + return 0; +} + +/* + * Disable hub-initiated and device-initiated U1 and U2 entry. + * Caller must own the bandwidth_mutex. + * + * This will call usb_enable_lpm() on failure, which will decrement + * lpm_disable_count, and will re-enable LPM if lpm_disable_count reaches zero. + */ +int usb_disable_lpm(struct usb_device *udev) +{ + struct usb_hcd *hcd; + + if (!udev || !udev->parent || + udev->speed != USB_SPEED_SUPER || + !udev->lpm_capable) + return 0; + + hcd = bus_to_hcd(udev->bus); + if (!hcd || !hcd->driver->disable_usb3_lpm_timeout) + return 0; + + udev->lpm_disable_count++; + if ((udev->u1_params.timeout == 0 && udev->u1_params.timeout == 0)) + return 0; + + /* If LPM is enabled, attempt to disable it. */ + if (usb_disable_link_state(hcd, udev, USB3_LPM_U1)) + goto enable_lpm; + if (usb_disable_link_state(hcd, udev, USB3_LPM_U2)) + goto enable_lpm; + + return 0; + +enable_lpm: + usb_enable_lpm(udev); + return -EBUSY; +} +EXPORT_SYMBOL_GPL(usb_disable_lpm); + +/* Grab the bandwidth_mutex before calling usb_disable_lpm() */ +int usb_unlocked_disable_lpm(struct usb_device *udev) +{ + struct usb_hcd *hcd = bus_to_hcd(udev->bus); + int ret; + + if (!hcd) + return -EINVAL; + + mutex_lock(hcd->bandwidth_mutex); + ret = usb_disable_lpm(udev); + mutex_unlock(hcd->bandwidth_mutex); + + return ret; +} +EXPORT_SYMBOL_GPL(usb_unlocked_disable_lpm); + +/* + * Attempt to enable device-initiated and hub-initiated U1 and U2 entry. The + * xHCI host policy may prevent U1 or U2 from being enabled. + * + * Other callers may have disabled link PM, so U1 and U2 entry will be disabled + * until the lpm_disable_count drops to zero. Caller must own the + * bandwidth_mutex. + */ +void usb_enable_lpm(struct usb_device *udev) +{ + struct usb_hcd *hcd; + + if (!udev || !udev->parent || + udev->speed != USB_SPEED_SUPER || + !udev->lpm_capable) + return; + + udev->lpm_disable_count--; + hcd = bus_to_hcd(udev->bus); + /* Double check that we can both enable and disable LPM. + * Device must be configured to accept set feature U1/U2 timeout. + */ + if (!hcd || !hcd->driver->enable_usb3_lpm_timeout || + !hcd->driver->disable_usb3_lpm_timeout) + return; + + if (udev->lpm_disable_count > 0) + return; + + usb_enable_link_state(hcd, udev, USB3_LPM_U1); + usb_enable_link_state(hcd, udev, USB3_LPM_U2); +} +EXPORT_SYMBOL_GPL(usb_enable_lpm); + +/* Grab the bandwidth_mutex before calling usb_enable_lpm() */ +void usb_unlocked_enable_lpm(struct usb_device *udev) +{ + struct usb_hcd *hcd = bus_to_hcd(udev->bus); + + if (!hcd) + return; + + mutex_lock(hcd->bandwidth_mutex); + usb_enable_lpm(udev); + mutex_unlock(hcd->bandwidth_mutex); +} +EXPORT_SYMBOL_GPL(usb_unlocked_enable_lpm); + + #else /* CONFIG_PM */ #define hub_suspend NULL #define hub_resume NULL #define hub_reset_resume NULL + +int usb_disable_lpm(struct usb_device *udev) +{ + return 0; +} + +void usb_enable_lpm(struct usb_device *udev) { } + +int usb_unlocked_disable_lpm(struct usb_device *udev) +{ + return 0; +} + +void usb_unlocked_enable_lpm(struct usb_device *udev) { } #endif diff --git a/include/linux/usb.h b/include/linux/usb.h index 22e7b53123ef..40439dfd81a7 100644 --- a/include/linux/usb.h +++ b/include/linux/usb.h @@ -409,6 +409,12 @@ struct usb3_lpm_parameters { * it will get data. */ unsigned int sel; + /* + * The idle timeout value that is currently programmed into the parent + * hub for this device. When the timer counts to zero, the parent hub + * will initiate an LPM transition to either U1 or U2. + */ + int timeout; }; /** @@ -468,8 +474,12 @@ struct usb3_lpm_parameters { * specific data for the device. * @slot_id: Slot ID assigned by xHCI * @removable: Device can be physically removed from this port - * @u1_params: exit latencies for U1 (USB 3.0 LPM). - * @u2_params: exit latencies for U2 (USB 3.0 LPM). + * @u1_params: exit latencies for USB3 U1 LPM state, and hub-initiated timeout. + * @u2_params: exit latencies for USB3 U2 LPM state, and hub-initiated timeout. + * @lpm_disable_count: Ref count used by usb_disable_lpm() and usb_enable_lpm() + * to keep track of the number of functions that require USB 3.0 Link Power + * Management to be disabled for this usb_device. This count should only + * be manipulated by those functions, with the bandwidth_mutex is held. * * Notes: * Usbcore drivers should not set usbdev->state directly. Instead use @@ -544,6 +554,7 @@ struct usb_device { enum usb_device_removable removable; struct usb3_lpm_parameters u1_params; struct usb3_lpm_parameters u2_params; + unsigned lpm_disable_count; }; #define to_usb_device(d) container_of(d, struct usb_device, dev) @@ -579,6 +590,12 @@ extern void usb_autopm_put_interface_async(struct usb_interface *intf); extern void usb_autopm_get_interface_no_resume(struct usb_interface *intf); extern void usb_autopm_put_interface_no_suspend(struct usb_interface *intf); +extern int usb_disable_lpm(struct usb_device *udev); +extern void usb_enable_lpm(struct usb_device *udev); +/* Same as above, but these functions lock/unlock the bandwidth_mutex. */ +extern int usb_unlocked_disable_lpm(struct usb_device *udev); +extern void usb_unlocked_enable_lpm(struct usb_device *udev); + static inline void usb_mark_last_busy(struct usb_device *udev) { pm_runtime_mark_last_busy(&udev->dev); diff --git a/include/linux/usb/ch11.h b/include/linux/usb/ch11.h index f1d26b6067f1..b6c2863b2c94 100644 --- a/include/linux/usb/ch11.h +++ b/include/linux/usb/ch11.h @@ -76,6 +76,8 @@ #define USB_PORT_FEAT_C_BH_PORT_RESET 29 #define USB_PORT_FEAT_FORCE_LINKPM_ACCEPT 30 +#define USB_PORT_LPM_TIMEOUT(p) (((p) & 0xff) << 8) + /* USB 3.0 hub remote wake mask bits, see table 10-14 */ #define USB_PORT_FEAT_REMOTE_WAKE_CONNECT (1 << 8) #define USB_PORT_FEAT_REMOTE_WAKE_DISCONNECT (1 << 9) diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h index e785d85b617f..43bce9da7a4d 100644 --- a/include/linux/usb/ch9.h +++ b/include/linux/usb/ch9.h @@ -935,6 +935,51 @@ enum usb_device_state { */ }; +enum usb3_link_state { + USB3_LPM_U0 = 0, + USB3_LPM_U1, + USB3_LPM_U2, + USB3_LPM_U3 +}; + +/* + * A U1 timeout of 0x0 means the parent hub will reject any transitions to U1. + * 0xff means the parent hub will accept transitions to U1, but will not + * initiate a transition. + * + * A U1 timeout of 0x1 to 0x7F also causes the hub to initiate a transition to + * U1 after that many microseconds. Timeouts of 0x80 to 0xFE are reserved + * values. + * + * A U2 timeout of 0x0 means the parent hub will reject any transitions to U2. + * 0xff means the parent hub will accept transitions to U2, but will not + * initiate a transition. + * + * A U2 timeout of 0x1 to 0xFE also causes the hub to initiate a transition to + * U2 after N*256 microseconds. Therefore a U2 timeout value of 0x1 means a U2 + * idle timer of 256 microseconds, 0x2 means 512 microseconds, 0xFE means + * 65.024ms. + */ +#define USB3_LPM_DISABLED 0x0 +#define USB3_LPM_U1_MAX_TIMEOUT 0x7F +#define USB3_LPM_U2_MAX_TIMEOUT 0xFE +#define USB3_LPM_DEVICE_INITIATED 0xFF + +struct usb_set_sel_req { + __u8 u1_sel; + __u8 u1_pel; + __le16 u2_sel; + __le16 u2_pel; +} __attribute__ ((packed)); + +/* + * The Set System Exit Latency control transfer provides one byte each for + * U1 SEL and U1 PEL, so the max exit latency is 0xFF. U2 SEL and U2 PEL each + * are two bytes long. + */ +#define USB3_LPM_MAX_U1_SEL_PEL 0xFF +#define USB3_LPM_MAX_U2_SEL_PEL 0xFFFF + /*-------------------------------------------------------------------------*/ /* diff --git a/include/linux/usb/hcd.h b/include/linux/usb/hcd.h index bbb946437070..7f855d50cdf5 100644 --- a/include/linux/usb/hcd.h +++ b/include/linux/usb/hcd.h @@ -344,6 +344,15 @@ struct hc_driver { */ int (*update_device)(struct usb_hcd *, struct usb_device *); int (*set_usb2_hw_lpm)(struct usb_hcd *, struct usb_device *, int); + /* USB 3.0 Link Power Management */ + /* Returns the USB3 hub-encoded value for the U1/U2 timeout. */ + int (*enable_usb3_lpm_timeout)(struct usb_hcd *, + struct usb_device *, enum usb3_link_state state); + /* The xHCI host controller can still fail the command to + * disable the LPM timeouts, so this can return an error code. + */ + int (*disable_usb3_lpm_timeout)(struct usb_hcd *, + struct usb_device *, enum usb3_link_state state); }; extern int usb_hcd_link_urb_to_ep(struct usb_hcd *hcd, struct urb *urb); -- cgit v1.2.3 From 8306095fd2c1100e8244c09bf560f97aca5a311d Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Wed, 2 May 2012 14:25:52 -0700 Subject: USB: Disable USB 3.0 LPM in critical sections. There are several places where the USB core needs to disable USB 3.0 Link PM: - usb_bind_interface - usb_unbind_interface - usb_driver_claim_interface - usb_port_suspend/usb_port_resume - usb_reset_and_verify_device - usb_set_interface - usb_reset_configuration - usb_set_configuration Use the new LPM disable/enable functions to temporarily disable LPM around these critical sections. We need to protect the critical section around binding and unbinding USB interface drivers. USB drivers may want to disable hub-initiated USB 3.0 LPM, which will change the value of the U1/U2 timeouts that the xHCI driver will install. We need to disable LPM completely until the driver is bound to the interface, and the driver has a chance to enable whatever alternate interface setting it needs in its probe routine. Then re-enable USB3 LPM, and recalculate the U1/U2 timeout values. We also need to disable LPM in usb_driver_claim_interface, because drivers like usbfs can bind to an interface through that function. Note, there is no way currently for userspace drivers to disable hub-initiated USB 3.0 LPM. Revisit this later. When a driver is unbound, the U1/U2 timeouts may change because we are unbinding the last driver that needed hub-initiated USB 3.0 LPM to be disabled. USB LPM must be disabled when a USB device is going to be suspended. The USB 3.0 spec does not define a state transition from U1 or U2 into U3, so we need to bring the device into U0 by disabling LPM before we can place it into U3. Therefore, call usb_unlocked_disable_lpm() in usb_port_suspend(), and call usb_unlocked_enable_lpm() in usb_port_resume(). If the port suspend fails, make sure to re-enable LPM by calling usb_unlocked_enable_lpm(), since usb_port_resume() will not be called on a failed port suspend. USB 3.0 devices lose their USB 3.0 LPM settings (including whether USB device-initiated LPM is enabled) across device suspend. Therefore, disable LPM before the device will be reset in usb_reset_and_verify_device(), and re-enable LPM after the reset is complete and the configuration/alt settings are re-installed. The calculated U1/U2 timeout values are heavily dependent on what USB device endpoints are currently enabled. When any of the enabled endpoints on the device might change, due to a new configuration, or new alternate interface setting, we need to first disable USB 3.0 LPM, add or delete endpoints from the xHCI schedule, install the new interfaces and alt settings, and then re-enable LPM. Do this in usb_set_interface, usb_reset_configuration, and usb_set_configuration. Basically, there is a call to disable and then enable LPM in all functions that lock the bandwidth_mutex. One exception is usb_disable_device, because the device is disconnecting or otherwise going away, and we should not care about whether USB 3.0 LPM is enabled. Signed-off-by: Sarah Sharp --- drivers/usb/core/driver.c | 54 +++++++++++++++++++++++++++++++++++++++++++++- drivers/usb/core/hub.c | 27 +++++++++++++++++++++++ drivers/usb/core/message.c | 38 ++++++++++++++++++++++++++++++++ include/linux/usb.h | 2 ++ 4 files changed, 120 insertions(+), 1 deletion(-) (limited to 'include/linux/usb.h') diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index f6f81c85c5cf..f536aebc958e 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -288,6 +288,7 @@ static int usb_probe_interface(struct device *dev) struct usb_device *udev = interface_to_usbdev(intf); const struct usb_device_id *id; int error = -ENODEV; + int lpm_disable_error; dev_dbg(dev, "%s\n", __func__); @@ -324,6 +325,25 @@ static int usb_probe_interface(struct device *dev) if (driver->supports_autosuspend) pm_runtime_enable(dev); + /* If the new driver doesn't allow hub-initiated LPM, and we can't + * disable hub-initiated LPM, then fail the probe. + * + * Otherwise, leaving LPM enabled should be harmless, because the + * endpoint intervals should remain the same, and the U1/U2 timeouts + * should remain the same. + * + * If we need to install alt setting 0 before probe, or another alt + * setting during probe, that should also be fine. usb_set_interface() + * will attempt to disable LPM, and fail if it can't disable it. + */ + lpm_disable_error = usb_unlocked_disable_lpm(udev); + if (lpm_disable_error && driver->disable_hub_initiated_lpm) { + dev_err(&intf->dev, "%s Failed to disable LPM for driver %s\n.", + __func__, driver->name); + error = lpm_disable_error; + goto err; + } + /* Carry out a deferred switch to altsetting 0 */ if (intf->needs_altsetting0) { error = usb_set_interface(udev, intf->altsetting[0]. @@ -338,6 +358,11 @@ static int usb_probe_interface(struct device *dev) goto err; intf->condition = USB_INTERFACE_BOUND; + + /* If the LPM disable succeeded, balance the ref counts. */ + if (!lpm_disable_error) + usb_unlocked_enable_lpm(udev); + usb_autosuspend_device(udev); return error; @@ -361,7 +386,7 @@ static int usb_unbind_interface(struct device *dev) struct usb_driver *driver = to_usb_driver(dev->driver); struct usb_interface *intf = to_usb_interface(dev); struct usb_device *udev; - int error, r; + int error, r, lpm_disable_error; intf->condition = USB_INTERFACE_UNBINDING; @@ -369,6 +394,13 @@ static int usb_unbind_interface(struct device *dev) udev = interface_to_usbdev(intf); error = usb_autoresume_device(udev); + /* Hub-initiated LPM policy may change, so attempt to disable LPM until + * the driver is unbound. If LPM isn't disabled, that's fine because it + * wouldn't be enabled unless all the bound interfaces supported + * hub-initiated LPM. + */ + lpm_disable_error = usb_unlocked_disable_lpm(udev); + /* Terminate all URBs for this interface unless the driver * supports "soft" unbinding. */ @@ -402,6 +434,10 @@ static int usb_unbind_interface(struct device *dev) intf->condition = USB_INTERFACE_UNBOUND; intf->needs_remote_wakeup = 0; + /* Attempt to re-enable USB3 LPM, if the disable succeeded. */ + if (!lpm_disable_error) + usb_unlocked_enable_lpm(udev); + /* Unbound interfaces are always runtime-PM-disabled and -suspended */ if (driver->supports_autosuspend) pm_runtime_disable(dev); @@ -442,17 +478,29 @@ int usb_driver_claim_interface(struct usb_driver *driver, struct usb_interface *iface, void *priv) { struct device *dev = &iface->dev; + struct usb_device *udev; int retval = 0; + int lpm_disable_error; if (dev->driver) return -EBUSY; + udev = interface_to_usbdev(iface); + dev->driver = &driver->drvwrap.driver; usb_set_intfdata(iface, priv); iface->needs_binding = 0; iface->condition = USB_INTERFACE_BOUND; + /* Disable LPM until this driver is bound. */ + lpm_disable_error = usb_unlocked_disable_lpm(udev); + if (lpm_disable_error && driver->disable_hub_initiated_lpm) { + dev_err(&iface->dev, "%s Failed to disable LPM for driver %s\n.", + __func__, driver->name); + return -ENOMEM; + } + /* Claimed interfaces are initially inactive (suspended) and * runtime-PM-enabled, but only if the driver has autosuspend * support. Otherwise they are marked active, to prevent the @@ -471,6 +519,10 @@ int usb_driver_claim_interface(struct usb_driver *driver, if (device_is_registered(dev)) retval = device_bind_driver(dev); + /* Attempt to re-enable USB3 LPM, if the disable was successful. */ + if (!lpm_disable_error) + usb_unlocked_enable_lpm(udev); + return retval; } EXPORT_SYMBOL_GPL(usb_driver_claim_interface); diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index fd1ec481aec1..fcc244e9056f 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -2702,6 +2702,12 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg) if (udev->usb2_hw_lpm_enabled == 1) usb_set_usb2_hardware_lpm(udev, 0); + if (usb_unlocked_disable_lpm(udev)) { + dev_err(&udev->dev, "%s Failed to disable LPM before suspend\n.", + __func__); + return -ENOMEM; + } + /* see 7.1.7.6 */ if (hub_is_superspeed(hub->hdev)) status = set_port_feature(hub->hdev, @@ -2725,6 +2731,9 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg) if (udev->usb2_hw_lpm_capable == 1) usb_set_usb2_hardware_lpm(udev, 1); + /* Try to enable USB3 LPM again */ + usb_unlocked_enable_lpm(udev); + /* System sleep transitions should never fail */ if (!PMSG_IS_AUTO(msg)) status = 0; @@ -2922,6 +2931,9 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg) /* Try to enable USB2 hardware LPM */ if (udev->usb2_hw_lpm_capable == 1) usb_set_usb2_hardware_lpm(udev, 1); + + /* Try to enable USB3 LPM */ + usb_unlocked_enable_lpm(udev); } return status; @@ -4681,11 +4693,22 @@ static int usb_reset_and_verify_device(struct usb_device *udev) goto done; mutex_lock(hcd->bandwidth_mutex); + /* Disable LPM while we reset the device and reinstall the alt settings. + * Device-initiated LPM settings, and system exit latency settings are + * cleared when the device is reset, so we have to set them up again. + */ + ret = usb_disable_lpm(udev); + if (ret) { + dev_err(&udev->dev, "%s Failed to disable LPM\n.", __func__); + mutex_unlock(hcd->bandwidth_mutex); + goto done; + } ret = usb_hcd_alloc_bandwidth(udev, udev->actconfig, NULL, NULL); if (ret < 0) { dev_warn(&udev->dev, "Busted HC? Not enough HCD resources for " "old configuration.\n"); + usb_enable_lpm(udev); mutex_unlock(hcd->bandwidth_mutex); goto re_enumerate; } @@ -4697,6 +4720,7 @@ static int usb_reset_and_verify_device(struct usb_device *udev) dev_err(&udev->dev, "can't restore configuration #%d (error=%d)\n", udev->actconfig->desc.bConfigurationValue, ret); + usb_enable_lpm(udev); mutex_unlock(hcd->bandwidth_mutex); goto re_enumerate; } @@ -4735,10 +4759,13 @@ static int usb_reset_and_verify_device(struct usb_device *udev) desc->bInterfaceNumber, desc->bAlternateSetting, ret); + usb_unlocked_enable_lpm(udev); goto re_enumerate; } } + /* Now that the alt settings are re-installed, enable LPM. */ + usb_unlocked_enable_lpm(udev); done: return 0; diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c index ca717da3be95..b548cf1dbc62 100644 --- a/drivers/usb/core/message.c +++ b/drivers/usb/core/message.c @@ -1308,10 +1308,19 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate) * Remove the current alt setting and add the new alt setting. */ mutex_lock(hcd->bandwidth_mutex); + /* Disable LPM, and re-enable it once the new alt setting is installed, + * so that the xHCI driver can recalculate the U1/U2 timeouts. + */ + if (usb_disable_lpm(dev)) { + dev_err(&iface->dev, "%s Failed to disable LPM\n.", __func__); + mutex_unlock(hcd->bandwidth_mutex); + return -ENOMEM; + } ret = usb_hcd_alloc_bandwidth(dev, NULL, iface->cur_altsetting, alt); if (ret < 0) { dev_info(&dev->dev, "Not enough bandwidth for altsetting %d\n", alternate); + usb_enable_lpm(dev); mutex_unlock(hcd->bandwidth_mutex); return ret; } @@ -1334,6 +1343,7 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate) } else if (ret < 0) { /* Re-instate the old alt setting */ usb_hcd_alloc_bandwidth(dev, NULL, alt, iface->cur_altsetting); + usb_enable_lpm(dev); mutex_unlock(hcd->bandwidth_mutex); return ret; } @@ -1354,6 +1364,9 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate) iface->cur_altsetting = alt; + /* Now that the interface is installed, re-enable LPM. */ + usb_unlocked_enable_lpm(dev); + /* If the interface only has one altsetting and the device didn't * accept the request, we attempt to carry out the equivalent action * by manually clearing the HALT feature for each endpoint in the @@ -1437,6 +1450,14 @@ int usb_reset_configuration(struct usb_device *dev) config = dev->actconfig; retval = 0; mutex_lock(hcd->bandwidth_mutex); + /* Disable LPM, and re-enable it once the configuration is reset, so + * that the xHCI driver can recalculate the U1/U2 timeouts. + */ + if (usb_disable_lpm(dev)) { + dev_err(&dev->dev, "%s Failed to disable LPM\n.", __func__); + mutex_unlock(hcd->bandwidth_mutex); + return -ENOMEM; + } /* Make sure we have enough bandwidth for each alternate setting 0 */ for (i = 0; i < config->desc.bNumInterfaces; i++) { struct usb_interface *intf = config->interface[i]; @@ -1465,6 +1486,7 @@ reset_old_alts: usb_hcd_alloc_bandwidth(dev, NULL, alt, intf->cur_altsetting); } + usb_enable_lpm(dev); mutex_unlock(hcd->bandwidth_mutex); return retval; } @@ -1502,6 +1524,8 @@ reset_old_alts: create_intf_ep_devs(intf); } } + /* Now that the interfaces are installed, re-enable LPM. */ + usb_unlocked_enable_lpm(dev); return 0; } EXPORT_SYMBOL_GPL(usb_reset_configuration); @@ -1763,8 +1787,18 @@ free_interfaces: * this call fails, the device state is unchanged. */ mutex_lock(hcd->bandwidth_mutex); + /* Disable LPM, and re-enable it once the new configuration is + * installed, so that the xHCI driver can recalculate the U1/U2 + * timeouts. + */ + if (usb_disable_lpm(dev)) { + dev_err(&dev->dev, "%s Failed to disable LPM\n.", __func__); + mutex_unlock(hcd->bandwidth_mutex); + return -ENOMEM; + } ret = usb_hcd_alloc_bandwidth(dev, cp, NULL, NULL); if (ret < 0) { + usb_enable_lpm(dev); mutex_unlock(hcd->bandwidth_mutex); usb_autosuspend_device(dev); goto free_interfaces; @@ -1784,6 +1818,7 @@ free_interfaces: if (!cp) { usb_set_device_state(dev, USB_STATE_ADDRESS); usb_hcd_alloc_bandwidth(dev, NULL, NULL, NULL); + usb_enable_lpm(dev); mutex_unlock(hcd->bandwidth_mutex); usb_autosuspend_device(dev); goto free_interfaces; @@ -1838,6 +1873,9 @@ free_interfaces: !(dev->quirks & USB_QUIRK_CONFIG_INTF_STRINGS)) cp->string = usb_cache_string(dev, cp->desc.iConfiguration); + /* Now that the interfaces are installed, re-enable LPM. */ + usb_unlocked_enable_lpm(dev); + /* Now that all the interfaces are set up, register them * to trigger binding of drivers to interfaces. probe() * routines may install different altsettings and may diff --git a/include/linux/usb.h b/include/linux/usb.h index 40439dfd81a7..c19297a8779c 100644 --- a/include/linux/usb.h +++ b/include/linux/usb.h @@ -526,6 +526,7 @@ struct usb_device { unsigned lpm_capable:1; unsigned usb2_hw_lpm_capable:1; unsigned usb2_hw_lpm_enabled:1; + unsigned usb3_lpm_enabled:1; int string_langid; /* static strings from the device */ @@ -555,6 +556,7 @@ struct usb_device { struct usb3_lpm_parameters u1_params; struct usb3_lpm_parameters u2_params; unsigned lpm_disable_count; + unsigned hub_initiated_lpm_disable_count; }; #define to_usb_device(d) container_of(d, struct usb_device, dev) -- cgit v1.2.3