From 12478cf0c55e5969f740bb38a24b1a0104ae18d8 Mon Sep 17 00:00:00 2001 From: "Srivatsa S. Bhat" Date: Mon, 24 Mar 2014 13:35:44 +0530 Subject: cpufreq: Make sure frequency transitions are serialized Whenever we change the frequency of a CPU, we call the PRECHANGE and POSTCHANGE notifiers. They must be serialized, i.e. PRECHANGE and POSTCHANGE notifiers should strictly alternate, thereby preventing two different sets of PRECHANGE or POSTCHANGE notifiers from interleaving arbitrarily. The following examples illustrate why this is important: Scenario 1: ----------- A thread reading the value of cpuinfo_cur_freq, will call __cpufreq_cpu_get()->cpufreq_out_of_sync()->cpufreq_notify_transition() The ondemand governor can decide to change the frequency of the CPU at the same time and hence it can end up sending the notifications via ->target(). If the notifiers are not serialized, the following sequence can occur: - PRECHANGE Notification for freq A (from cpuinfo_cur_freq) - PRECHANGE Notification for freq B (from target()) - Freq changed by target() to B - POSTCHANGE Notification for freq B - POSTCHANGE Notification for freq A We can see from the above that the last POSTCHANGE Notification happens for freq A but the hardware is set to run at freq B. Where would we break then?: adjust_jiffies() in cpufreq.c & cpufreq_callback() in arch/arm/kernel/smp.c (which also adjusts the jiffies). All the loops_per_jiffy calculations will get messed up. Scenario 2: ----------- The governor calls __cpufreq_driver_target() to change the frequency. At the same time, if we change scaling_{min|max}_freq from sysfs, it will end up calling the governor's CPUFREQ_GOV_LIMITS notification, which will also call __cpufreq_driver_target(). And hence we end up issuing concurrent calls to ->target(). Typically, platforms have the following logic in their ->target() routines: (Eg: cpufreq-cpu0, omap, exynos, etc) A. If new freq is more than old: Increase voltage B. Change freq C. If new freq is less than old: decrease voltage Now, if the two concurrent calls to ->target() are X and Y, where X is trying to increase the freq and Y is trying to decrease it, we get the following race condition: X.A: voltage gets increased for larger freq Y.A: nothing happens Y.B: freq gets decreased Y.C: voltage gets decreased X.B: freq gets increased X.C: nothing happens Thus we can end up setting a freq which is not supported by the voltage we have set. That will probably make the clock to the CPU unstable and the system might not work properly anymore. This patch introduces a set of synchronization primitives to serialize frequency transitions, which are to be used as shown below: cpufreq_freq_transition_begin(); //Perform the frequency change cpufreq_freq_transition_end(); The _begin() call sends the PRECHANGE notification whereas the _end() call sends the POSTCHANGE notification. Also, all the necessary synchronization is handled within these calls. In particular, even drivers which set the ASYNC_NOTIFICATION flag can also use these APIs for performing frequency transitions (ie., you can call _begin() from one task, and call the corresponding _end() from a different task). The actual synchronization underneath is not that complicated: The key challenge is to allow drivers to begin the transition from one thread and end it in a completely different thread (this is to enable drivers that do asynchronous POSTCHANGE notification from bottom-halves, to also use the same interface). To achieve this, a 'transition_ongoing' flag, a 'transition_lock' spinlock and a wait-queue are added per-policy. The flag and the wait-queue are used in conjunction to create an "uninterrupted flow" from _begin() to _end(). The spinlock is used to ensure that only one such "flow" is in flight at any given time. Put together, this provides us all the necessary synchronization. Signed-off-by: Srivatsa S. Bhat Signed-off-by: Viresh Kumar Signed-off-by: Rafael J. Wysocki --- include/linux/cpufreq.h | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'include/linux/cpufreq.h') diff --git a/include/linux/cpufreq.h b/include/linux/cpufreq.h index 2d2e62c8666a..e33760268a86 100644 --- a/include/linux/cpufreq.h +++ b/include/linux/cpufreq.h @@ -16,6 +16,7 @@ #include #include #include +#include #include /********************************************************************* @@ -104,6 +105,11 @@ struct cpufreq_policy { * __cpufreq_governor(data, CPUFREQ_GOV_POLICY_EXIT); */ struct rw_semaphore rwsem; + + /* Synchronization for frequency transitions */ + bool transition_ongoing; /* Tracks transition status */ + spinlock_t transition_lock; + wait_queue_head_t transition_wait; }; /* Only for ACPI */ @@ -337,6 +343,10 @@ void cpufreq_notify_transition(struct cpufreq_policy *policy, struct cpufreq_freqs *freqs, unsigned int state); void cpufreq_notify_post_transition(struct cpufreq_policy *policy, struct cpufreq_freqs *freqs, int transition_failed); +void cpufreq_freq_transition_begin(struct cpufreq_policy *policy, + struct cpufreq_freqs *freqs); +void cpufreq_freq_transition_end(struct cpufreq_policy *policy, + struct cpufreq_freqs *freqs, int transition_failed); #else /* CONFIG_CPU_FREQ */ static inline int cpufreq_register_notifier(struct notifier_block *nb, -- cgit v1.2.3