From 7f7c8a619253c83cf3b1071df3b001811d0c1a6c Mon Sep 17 00:00:00 2001 From: eric miao Date: Thu, 3 Jan 2008 11:25:56 +0800 Subject: [ARM] pxa: make MFP configuration processor independent There are two reasons for making the MFP configuration to be processor independent, i.e. removing the relationship of configuration bits with actual MFPR register settings: 1. power management sometimes requires the MFP to be configured differently when in run mode or in low power mode 2. for future integration of pxa{25x,27x} GPIO configurations The modifications include: 1. introducing of processor independent MFP configuration bits, as defined in [include/asm-arm/arch-pxa/mfp.h]: bit 0.. 9 - MFP Pin Number (1024 Pins Maximum) bit 10..12 - Alternate Function Selection bit 13..15 - Drive Strength bit 16..18 - Low Power Mode State bit 19..20 - Low Power Mode Edge Detection bit 21..22 - Run Mode Pull State and so on, 2. moving the processor dependent code from mfp.h into mfp-pxa3xx.h 3. cleaning up of the MFPR bit definitions 4. mapping of processor independent MFP configuration into processor specific MFPR register settings is now totally encapsulated within pxa3xx_mfp_config() 5. using of "unsigned long" instead of invented type of "mfp_cfg_t" according to Documentation/CodingStyle Chapter 5, usage of this in platform code will be slowly removed in later patches Signed-off-by: eric miao Signed-off-by: Russell King --- include/asm-arm/arch-pxa/mfp.h | 262 +++++++++++------------------------------ 1 file changed, 68 insertions(+), 194 deletions(-) (limited to 'include/asm-arm/arch-pxa/mfp.h') diff --git a/include/asm-arm/arch-pxa/mfp.h b/include/asm-arm/arch-pxa/mfp.h index 60fbed1b2e89..02f6157396d3 100644 --- a/include/asm-arm/arch-pxa/mfp.h +++ b/include/asm-arm/arch-pxa/mfp.h @@ -16,9 +16,6 @@ #ifndef __ASM_ARCH_MFP_H #define __ASM_ARCH_MFP_H -#define MFPR_BASE (0x40e10000) -#define MFPR_SIZE (PAGE_SIZE) - #define mfp_to_gpio(m) ((m) % 128) /* list of all the configurable MFP pins */ @@ -216,115 +213,22 @@ enum { MFP_PIN_MAX, }; -/* - * Table that determines the low power modes outputs, with actual settings - * used in parentheses for don't-care values. Except for the float output, - * the configured driven and pulled levels match, so if there is a need for - * non-LPM pulled output, the same configuration could probably be used. - * - * Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel - * (bit 7) (bit 8) (bit 14d) (bit 13d) - * - * Drive 0 0 0 0 X (1) 0 - * Drive 1 0 1 X (1) 0 0 - * Pull hi (1) 1 X(1) 1 0 0 - * Pull lo (0) 1 X(0) 0 1 0 - * Z (float) 1 X(0) 0 0 0 - */ -#define MFP_LPM_DRIVE_LOW 0x8 -#define MFP_LPM_DRIVE_HIGH 0x6 -#define MFP_LPM_PULL_HIGH 0x7 -#define MFP_LPM_PULL_LOW 0x9 -#define MFP_LPM_FLOAT 0x1 -#define MFP_LPM_PULL_NEITHER 0x0 - -/* - * The pullup and pulldown state of the MFP pin is by default determined by - * selected alternate function. In case some buggy devices need to override - * this default behavior, pxa3xx_mfp_set_pull() can be invoked with one of - * the following definition as the parameter. - * - * Definition pull_sel pullup_en pulldown_en - * MFP_PULL_HIGH 1 1 0 - * MFP_PULL_LOW 1 0 1 - * MFP_PULL_BOTH 1 1 1 - * MFP_PULL_NONE 1 0 0 - * MFP_PULL_DEFAULT 0 X X - * - * NOTE: pxa3xx_mfp_set_pull() will modify the PULLUP_EN and PULLDOWN_EN - * bits, which will cause potential conflicts with the low power mode - * setting, device drivers should take care of this - */ -#define MFP_PULL_BOTH (0x7u) -#define MFP_PULL_HIGH (0x6u) -#define MFP_PULL_LOW (0x5u) -#define MFP_PULL_NONE (0x4u) -#define MFP_PULL_DEFAULT (0x0u) - -#define MFP_AF0 (0) -#define MFP_AF1 (1) -#define MFP_AF2 (2) -#define MFP_AF3 (3) -#define MFP_AF4 (4) -#define MFP_AF5 (5) -#define MFP_AF6 (6) -#define MFP_AF7 (7) - -#define MFP_DS01X (0) -#define MFP_DS02X (1) -#define MFP_DS03X (2) -#define MFP_DS04X (3) -#define MFP_DS06X (4) -#define MFP_DS08X (5) -#define MFP_DS10X (6) -#define MFP_DS12X (7) - -#define MFP_EDGE_BOTH 0x3 -#define MFP_EDGE_RISE 0x2 -#define MFP_EDGE_FALL 0x1 -#define MFP_EDGE_NONE 0x0 - -#define MFPR_AF_MASK 0x0007 -#define MFPR_DRV_MASK 0x1c00 -#define MFPR_RDH_MASK 0x0200 -#define MFPR_LPM_MASK 0xe180 -#define MFPR_PULL_MASK 0xe000 -#define MFPR_EDGE_MASK 0x0070 - -#define MFPR_ALT_OFFSET 0 -#define MFPR_ERE_OFFSET 4 -#define MFPR_EFE_OFFSET 5 -#define MFPR_EC_OFFSET 6 -#define MFPR_SON_OFFSET 7 -#define MFPR_SD_OFFSET 8 -#define MFPR_SS_OFFSET 9 -#define MFPR_DRV_OFFSET 10 -#define MFPR_PD_OFFSET 13 -#define MFPR_PU_OFFSET 14 -#define MFPR_PS_OFFSET 15 - -#define MFPR(af, drv, rdh, lpm, edge) \ - (((af) & 0x7) | (((drv) & 0x7) << 10) |\ - (((rdh) & 0x1) << 9) |\ - (((lpm) & 0x3) << 7) |\ - (((lpm) & 0x4) << 12)|\ - (((lpm) & 0x8) << 10)|\ - ((!(edge)) << 6) |\ - (((edge) & 0x1) << 5) |\ - (((edge) & 0x2) << 3)) - /* * a possible MFP configuration is represented by a 32-bit integer - * bit 0..15 - MFPR value (16-bit) - * bit 16..31 - mfp pin index (used to obtain the MFPR offset) + * + * bit 0.. 9 - MFP Pin Number (1024 Pins Maximum) + * bit 10..12 - Alternate Function Selection + * bit 13..15 - Drive Strength + * bit 16..18 - Low Power Mode State + * bit 19..20 - Low Power Mode Edge Detection + * bit 21..22 - Run Mode Pull State * * to facilitate the definition, the following macros are provided * - * MFPR_DEFAULT - default MFPR value, with + * MFP_CFG_DEFAULT - default MFP configuration value, with * alternate function = 0, - * drive strength = fast 1mA (MFP_DS01X) + * drive strength = fast 3mA (MFP_DS03X) * low power mode = default - * release dalay hold = false (RDH bit) * edge detection = none * * MFP_CFG - default MFPR value with alternate function @@ -334,104 +238,74 @@ enum { * low power mode * MFP_CFG_X - default MFPR value with alternate function, * pin drive strength and low power mode - * - * use - * - * MFP_CFG_PIN - to get the MFP pin index - * MFP_CFG_VAL - to get the corresponding MFPR value */ -typedef uint32_t mfp_cfg_t; - -#define MFP_CFG_PIN(mfp_cfg) (((mfp_cfg) >> 16) & 0xffff) -#define MFP_CFG_VAL(mfp_cfg) ((mfp_cfg) & 0xffff) - -/* - * MFP register defaults to - * drive strength fast 3mA (010'b) - * edge detection logic disabled - * alternate function 0 - */ -#define MFPR_DEFAULT (0x0840) +typedef unsigned long mfp_cfg_t; + +#define MFP_PIN(x) ((x) & 0x3ff) + +#define MFP_AF0 (0x0 << 10) +#define MFP_AF1 (0x1 << 10) +#define MFP_AF2 (0x2 << 10) +#define MFP_AF3 (0x3 << 10) +#define MFP_AF4 (0x4 << 10) +#define MFP_AF5 (0x5 << 10) +#define MFP_AF6 (0x6 << 10) +#define MFP_AF7 (0x7 << 10) +#define MFP_AF_MASK (0x7 << 10) +#define MFP_AF(x) (((x) >> 10) & 0x7) + +#define MFP_DS01X (0x0 << 13) +#define MFP_DS02X (0x1 << 13) +#define MFP_DS03X (0x2 << 13) +#define MFP_DS04X (0x3 << 13) +#define MFP_DS06X (0x4 << 13) +#define MFP_DS08X (0x5 << 13) +#define MFP_DS10X (0x6 << 13) +#define MFP_DS13X (0x7 << 13) +#define MFP_DS_MASK (0x7 << 13) +#define MFP_DS(x) (((x) >> 13) & 0x7) + +#define MFP_LPM_INPUT (0x0 << 16) +#define MFP_LPM_DRIVE_LOW (0x1 << 16) +#define MFP_LPM_DRIVE_HIGH (0x2 << 16) +#define MFP_LPM_PULL_LOW (0x3 << 16) +#define MFP_LPM_PULL_HIGH (0x4 << 16) +#define MFP_LPM_FLOAT (0x5 << 16) +#define MFP_LPM_STATE_MASK (0x7 << 16) +#define MFP_LPM_STATE(x) (((x) >> 16) & 0x7) + +#define MFP_LPM_EDGE_NONE (0x0 << 19) +#define MFP_LPM_EDGE_RISE (0x1 << 19) +#define MFP_LPM_EDGE_FALL (0x2 << 19) +#define MFP_LPM_EDGE_BOTH (0x3 << 19) +#define MFP_LPM_EDGE_MASK (0x3 << 19) +#define MFP_LPM_EDGE(x) (((x) >> 19) & 0x3) + +#define MFP_PULL_NONE (0x0 << 21) +#define MFP_PULL_LOW (0x1 << 21) +#define MFP_PULL_HIGH (0x2 << 21) +#define MFP_PULL_BOTH (0x3 << 21) +#define MFP_PULL_MASK (0x3 << 21) +#define MFP_PULL(x) (((x) >> 21) & 0x3) + +#define MFP_CFG_DEFAULT (MFP_AF0 | MFP_DS03X | MFP_LPM_INPUT |\ + MFP_LPM_EDGE_NONE | MFP_PULL_NONE) #define MFP_CFG(pin, af) \ - ((MFP_PIN_##pin << 16) | MFPR_DEFAULT | (MFP_##af)) + ((MFP_CFG_DEFAULT & ~MFP_AF_MASK) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af)) #define MFP_CFG_DRV(pin, af, drv) \ - ((MFP_PIN_##pin << 16) | (MFPR_DEFAULT & ~MFPR_DRV_MASK) |\ - ((MFP_##drv) << 10) | (MFP_##af)) + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK)) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv)) #define MFP_CFG_LPM(pin, af, lpm) \ - ((MFP_PIN_##pin << 16) | (MFPR_DEFAULT & ~MFPR_LPM_MASK) |\ - (((MFP_LPM_##lpm) & 0x3) << 7) |\ - (((MFP_LPM_##lpm) & 0x4) << 12) |\ - (((MFP_LPM_##lpm) & 0x8) << 10) |\ - (MFP_##af)) + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_LPM_STATE_MASK)) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_LPM_##lpm)) #define MFP_CFG_X(pin, af, drv, lpm) \ - ((MFP_PIN_##pin << 16) |\ - (MFPR_DEFAULT & ~(MFPR_DRV_MASK | MFPR_LPM_MASK)) |\ - ((MFP_##drv) << 10) | (MFP_##af) |\ - (((MFP_LPM_##lpm) & 0x3) << 7) |\ - (((MFP_LPM_##lpm) & 0x4) << 12) |\ - (((MFP_LPM_##lpm) & 0x8) << 10)) - -/* - * each MFP pin will have a MFPR register, since the offset of the - * register varies between processors, the processor specific code - * should initialize the pin offsets by pxa3xx_mfp_init_addr() - * - * pxa3xx_mfp_init_addr - accepts a table of "pxa3xx_mfp_addr_map" - * structure, which represents a range of MFP pins from "start" to - * "end", with the offset begining at "offset", to define a single - * pin, let "end" = -1 - * - * use - * - * MFP_ADDR_X() to define a range of pins - * MFP_ADDR() to define a single pin - * MFP_ADDR_END to signal the end of pin offset definitions - */ -struct pxa3xx_mfp_addr_map { - unsigned int start; - unsigned int end; - unsigned long offset; -}; - -#define MFP_ADDR_X(start, end, offset) \ - { MFP_PIN_##start, MFP_PIN_##end, offset } - -#define MFP_ADDR(pin, offset) \ - { MFP_PIN_##pin, -1, offset } - -#define MFP_ADDR_END { MFP_PIN_INVALID, 0 } - -struct pxa3xx_mfp_pin { - unsigned long mfpr_off; /* MFPRxx register offset */ - unsigned long mfpr_val; /* MFPRxx register value */ -}; - -/* - * pxa3xx_mfp_read()/pxa3xx_mfp_write() - for direct read/write access - * to the MFPR register - */ -unsigned long pxa3xx_mfp_read(int mfp); -void pxa3xx_mfp_write(int mfp, unsigned long mfpr_val); - -/* - * pxa3xx_mfp_config - configure the MFPR registers - * - * used by board specific initialization code - */ -void pxa3xx_mfp_config(mfp_cfg_t *mfp_cfgs, int num); - -/* - * pxa3xx_mfp_init_addr() - initialize the mapping between mfp pin - * index and MFPR register offset - * - * used by processor specific code - */ -void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *); -void __init pxa3xx_init_mfp(void); + ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK | MFP_LPM_STATE_MASK)) |\ + (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv | MFP_LPM_##lpm)) #endif /* __ASM_ARCH_MFP_H */ -- cgit v1.2.3