From aaeb6cdfa5c07533c2cd6d2c381374c69f7db9dc Mon Sep 17 00:00:00 2001
From: Jiri Pirko <jiri@resnulli.us>
Date: Tue, 8 Jan 2013 01:38:26 +0000
Subject: remove init of dev->perm_addr in drivers

perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index fbf75fdca994..337644dda14d 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -6228,11 +6228,10 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 			"NVM Read Error while reading MAC address\n");
 
 	memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
-	memcpy(netdev->perm_addr, adapter->hw.mac.addr, netdev->addr_len);
 
-	if (!is_valid_ether_addr(netdev->perm_addr)) {
+	if (!is_valid_ether_addr(netdev->dev_addr)) {
 		dev_err(&pdev->dev, "Invalid MAC Address: %pM\n",
-			netdev->perm_addr);
+			netdev->dev_addr);
 		err = -EIO;
 		goto err_eeprom;
 	}
-- 
cgit v1.2.3


From 1241f29fa3c6fa95f20e3e77452f8d6d60deae7a Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:25:42 +0000
Subject: e1000e: SerDes autoneg flow control

Enables flow control to be set in SerDes autoneg mode. This is what is
done for copper, but relies on a different set of register/bit checks
since this is all done within the Mac registers.

Remove inapplicable comment in defines.h

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |   6 +-
 drivers/net/ethernet/intel/e1000e/hw.h      |   4 +
 drivers/net/ethernet/intel/e1000e/mac.c     | 125 ++++++++++++++++++++++++++++
 3 files changed, 132 insertions(+), 3 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 02a12b69555f..20735327a7a0 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -241,9 +241,9 @@
 #define E1000_CTRL_VME      0x40000000  /* IEEE VLAN mode enable */
 #define E1000_CTRL_PHY_RST  0x80000000  /* PHY Reset */
 
-/* Bit definitions for the Management Data IO (MDIO) and Management Data
- * Clock (MDC) pins in the Device Control Register.
- */
+#define E1000_PCS_LCTL_FORCE_FCTRL	0x80
+
+#define E1000_PCS_LSTS_AN_COMPLETE	0x10000
 
 /* Device Status */
 #define E1000_STATUS_FD         0x00000001      /* Full duplex.0=half,1=full */
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index cf217777586c..06239fe47db1 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -191,6 +191,10 @@ enum e1e_registers {
 	E1000_ICTXQMTC = 0x0411C, /* Irq Cause Tx Queue MinThreshold Count */
 	E1000_ICRXDMTC = 0x04120, /* Irq Cause Rx Desc MinThreshold Count */
 	E1000_ICRXOC   = 0x04124, /* Irq Cause Receiver Overrun Count */
+	E1000_PCS_LCTL = 0x04208, /* PCS Link Control - RW */
+	E1000_PCS_LSTAT = 0x0420C, /* PCS Link Status - RO */
+	E1000_PCS_ANADV = 0x04218, /* AN advertisement - RW */
+	E1000_PCS_LPAB = 0x0421C, /* Link Partner Ability - RW */
 	E1000_RXCSUM   = 0x05000, /* Rx Checksum Control - RW */
 	E1000_RFCTL    = 0x05008, /* Receive Filter Control */
 	E1000_MTA      = 0x05200, /* Multicast Table Array - RW Array */
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index 54d9dafaf126..0fa4c0656e09 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -1021,6 +1021,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 {
 	struct e1000_mac_info *mac = &hw->mac;
 	s32 ret_val = 0;
+	u32 pcs_status_reg, pcs_adv_reg, pcs_lp_ability_reg, pcs_ctrl_reg;
 	u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg;
 	u16 speed, duplex;
 
@@ -1185,6 +1186,130 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		}
 	}
 
+	/* Check for the case where we have SerDes media and auto-neg is
+	 * enabled.  In this case, we need to check and see if Auto-Neg
+	 * has completed, and if so, how the PHY and link partner has
+	 * flow control configured.
+	 */
+	if ((hw->phy.media_type == e1000_media_type_internal_serdes) &&
+	    mac->autoneg) {
+		/* Read the PCS_LSTS and check to see if AutoNeg
+		 * has completed.
+		 */
+		pcs_status_reg = er32(PCS_LSTAT);
+
+		if (!(pcs_status_reg & E1000_PCS_LSTS_AN_COMPLETE)) {
+			e_dbg("PCS Auto Neg has not completed.\n");
+			return ret_val;
+		}
+
+		/* The AutoNeg process has completed, so we now need to
+		 * read both the Auto Negotiation Advertisement
+		 * Register (PCS_ANADV) and the Auto_Negotiation Base
+		 * Page Ability Register (PCS_LPAB) to determine how
+		 * flow control was negotiated.
+		 */
+		pcs_adv_reg = er32(PCS_ANADV);
+		pcs_lp_ability_reg = er32(PCS_LPAB);
+
+		/* Two bits in the Auto Negotiation Advertisement Register
+		 * (PCS_ANADV) and two bits in the Auto Negotiation Base
+		 * Page Ability Register (PCS_LPAB) determine flow control
+		 * for both the PHY and the link partner.  The following
+		 * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+		 * 1999, describes these PAUSE resolution bits and how flow
+		 * control is determined based upon these settings.
+		 * NOTE:  DC = Don't Care
+		 *
+		 *   LOCAL DEVICE  |   LINK PARTNER
+		 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+		 *-------|---------|-------|---------|--------------------
+		 *   0   |    0    |  DC   |   DC    | e1000_fc_none
+		 *   0   |    1    |   0   |   DC    | e1000_fc_none
+		 *   0   |    1    |   1   |    0    | e1000_fc_none
+		 *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
+		 *   1   |    0    |   0   |   DC    | e1000_fc_none
+		 *   1   |   DC    |   1   |   DC    | e1000_fc_full
+		 *   1   |    1    |   0   |    0    | e1000_fc_none
+		 *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
+		 *
+		 * Are both PAUSE bits set to 1?  If so, this implies
+		 * Symmetric Flow Control is enabled at both ends.  The
+		 * ASM_DIR bits are irrelevant per the spec.
+		 *
+		 * For Symmetric Flow Control:
+		 *
+		 *   LOCAL DEVICE  |   LINK PARTNER
+		 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+		 *-------|---------|-------|---------|--------------------
+		 *   1   |   DC    |   1   |   DC    | e1000_fc_full
+		 *
+		 */
+		if ((pcs_adv_reg & E1000_TXCW_PAUSE) &&
+		    (pcs_lp_ability_reg & E1000_TXCW_PAUSE)) {
+			/* Now we need to check if the user selected Rx ONLY
+			 * of pause frames.  In this case, we had to advertise
+			 * FULL flow control because we could not advertise Rx
+			 * ONLY. Hence, we must now check to see if we need to
+			 * turn OFF the TRANSMISSION of PAUSE frames.
+			 */
+			if (hw->fc.requested_mode == e1000_fc_full) {
+				hw->fc.current_mode = e1000_fc_full;
+				e_dbg("Flow Control = FULL.\n");
+			} else {
+				hw->fc.current_mode = e1000_fc_rx_pause;
+				e_dbg("Flow Control = Rx PAUSE frames only.\n");
+			}
+		}
+		/* For receiving PAUSE frames ONLY.
+		 *
+		 *   LOCAL DEVICE  |   LINK PARTNER
+		 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+		 *-------|---------|-------|---------|--------------------
+		 *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
+		 */
+		else if (!(pcs_adv_reg & E1000_TXCW_PAUSE) &&
+			 (pcs_adv_reg & E1000_TXCW_ASM_DIR) &&
+			 (pcs_lp_ability_reg & E1000_TXCW_PAUSE) &&
+			 (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) {
+			hw->fc.current_mode = e1000_fc_tx_pause;
+			e_dbg("Flow Control = Tx PAUSE frames only.\n");
+		}
+		/* For transmitting PAUSE frames ONLY.
+		 *
+		 *   LOCAL DEVICE  |   LINK PARTNER
+		 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+		 *-------|---------|-------|---------|--------------------
+		 *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
+		 */
+		else if ((pcs_adv_reg & E1000_TXCW_PAUSE) &&
+			 (pcs_adv_reg & E1000_TXCW_ASM_DIR) &&
+			 !(pcs_lp_ability_reg & E1000_TXCW_PAUSE) &&
+			 (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) {
+			hw->fc.current_mode = e1000_fc_rx_pause;
+			e_dbg("Flow Control = Rx PAUSE frames only.\n");
+		} else {
+			/* Per the IEEE spec, at this point flow control
+			 * should be disabled.
+			 */
+			hw->fc.current_mode = e1000_fc_none;
+			e_dbg("Flow Control = NONE.\n");
+		}
+
+		/* Now we call a subroutine to actually force the MAC
+		 * controller to use the correct flow control settings.
+		 */
+		pcs_ctrl_reg = er32(PCS_LCTL);
+		pcs_ctrl_reg |= E1000_PCS_LCTL_FORCE_FCTRL;
+		ew32(PCS_LCTL, pcs_ctrl_reg);
+
+		ret_val = e1000e_force_mac_fc(hw);
+		if (ret_val) {
+			e_dbg("Error forcing flow control settings\n");
+			return ret_val;
+		}
+	}
+
 	return 0;
 }
 
-- 
cgit v1.2.3


From 635ab56439e21cbea6be346ac71222f9c4ac6463 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:25:47 +0000
Subject: e1000e: Acquire/release semaphore when writing each EEPROM page

When data blocks are written to the EEPROM, the HW/SW/FW semaphore must be
held for the duration.  With large data blocks on 80003es2lan, 82571 and
82572, this can take too long and cause the firmware to take ownership of
the semaphore and consequently ownership of writes to the EEPROM.
Instead, acquire and release the semaphore for each page of the block
written.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/nvm.c | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/nvm.c b/drivers/net/ethernet/intel/e1000e/nvm.c
index b6468804cb2e..71938ed2d3c3 100644
--- a/drivers/net/ethernet/intel/e1000e/nvm.c
+++ b/drivers/net/ethernet/intel/e1000e/nvm.c
@@ -359,7 +359,7 @@ s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 {
 	struct e1000_nvm_info *nvm = &hw->nvm;
-	s32 ret_val;
+	s32 ret_val = -E1000_ERR_NVM;
 	u16 widx = 0;
 
 	/* A check for invalid values:  offset too large, too many words,
@@ -371,16 +371,18 @@ s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 		return -E1000_ERR_NVM;
 	}
 
-	ret_val = nvm->ops.acquire(hw);
-	if (ret_val)
-		return ret_val;
-
 	while (widx < words) {
 		u8 write_opcode = NVM_WRITE_OPCODE_SPI;
 
-		ret_val = e1000_ready_nvm_eeprom(hw);
+		ret_val = nvm->ops.acquire(hw);
 		if (ret_val)
-			goto release;
+			return ret_val;
+
+		ret_val = e1000_ready_nvm_eeprom(hw);
+		if (ret_val) {
+			nvm->ops.release(hw);
+			return ret_val;
+		}
 
 		e1000_standby_nvm(hw);
 
@@ -413,12 +415,10 @@ s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 				break;
 			}
 		}
+		usleep_range(10000, 20000);
+		nvm->ops.release(hw);
 	}
 
-	usleep_range(10000, 20000);
-release:
-	nvm->ops.release(hw);
-
 	return ret_val;
 }
 
-- 
cgit v1.2.3


From 1cc7a3a14fa60f31ca4ff69f0dd31f369e0a51c2 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 9 Jan 2013 08:15:42 +0000
Subject: e1000e: Invalid Image CSUM bit changed for I217

On I217, the bit that indicates an invalid EEPROM (NVM) image checksum has
changed from previous ICH/PCH LOMs.  When validating the EEPROM checksum,
check the appropriate bit on different devices.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  4 ++++
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 29 +++++++++++++++++++++--------
 2 files changed, 25 insertions(+), 8 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 20735327a7a0..7326ea2fef8f 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -639,6 +639,10 @@
 /* NVM Word Offsets */
 #define NVM_COMPAT                 0x0003
 #define NVM_ID_LED_SETTINGS        0x0004
+#define NVM_FUTURE_INIT_WORD1      0x0019
+#define NVM_COMPAT_VALID_CSUM      0x0001
+#define NVM_FUTURE_INIT_WORD1_VALID_CSUM	0x0040
+
 #define NVM_INIT_CONTROL2_REG      0x000F
 #define NVM_INIT_CONTROL3_PORT_B   0x0014
 #define NVM_INIT_3GIO_3            0x001A
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 976336547607..7d5f6b7856e6 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -2949,19 +2949,32 @@ static s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw)
 {
 	s32 ret_val;
 	u16 data;
+	u16 word;
+	u16 valid_csum_mask;
 
-	/* Read 0x19 and check bit 6.  If this bit is 0, the checksum
-	 * needs to be fixed.  This bit is an indication that the NVM
-	 * was prepared by OEM software and did not calculate the
-	 * checksum...a likely scenario.
+	/* Read NVM and check Invalid Image CSUM bit.  If this bit is 0,
+	 * the checksum needs to be fixed.  This bit is an indication that
+	 * the NVM was prepared by OEM software and did not calculate
+	 * the checksum...a likely scenario.
 	 */
-	ret_val = e1000_read_nvm(hw, 0x19, 1, &data);
+	switch (hw->mac.type) {
+	case e1000_pch_lpt:
+		word = NVM_COMPAT;
+		valid_csum_mask = NVM_COMPAT_VALID_CSUM;
+		break;
+	default:
+		word = NVM_FUTURE_INIT_WORD1;
+		valid_csum_mask = NVM_FUTURE_INIT_WORD1_VALID_CSUM;
+		break;
+	}
+
+	ret_val = e1000_read_nvm(hw, word, 1, &data);
 	if (ret_val)
 		return ret_val;
 
-	if (!(data & 0x40)) {
-		data |= 0x40;
-		ret_val = e1000_write_nvm(hw, 0x19, 1, &data);
+	if (!(data & valid_csum_mask)) {
+		data |= valid_csum_mask;
+		ret_val = e1000_write_nvm(hw, word, 1, &data);
 		if (ret_val)
 			return ret_val;
 		ret_val = e1000e_update_nvm_checksum(hw);
-- 
cgit v1.2.3


From 4ddc48a9a5f3352343eb4725eb75f9ca38fa1559 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:25:58 +0000
Subject: e1000e: helper functions for accessing EMI registers

The Extended Management Interface (EMI) registers are accessed by first
writing the EMI register offset to the EMI_ADDR regiter and then either
reading or writing the data to/from the EMI_DATA register.  Add helper
functions for performing these steps and convert existing EMI register
accesses accordingly.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 84 ++++++++++++++++++++++-------
 1 file changed, 65 insertions(+), 19 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 7d5f6b7856e6..8004d7113c39 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -153,7 +153,7 @@
 #define I82579_LPI_CTRL_ENABLE_MASK		0x6000
 #define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
 
-/* EMI Registers */
+/* Extended Management Interface (EMI) Registers */
 #define I82579_EMI_ADDR         0x10
 #define I82579_EMI_DATA         0x11
 #define I82579_LPI_UPDATE_TIMER 0x4805	/* in 40ns units + 40 ns base value */
@@ -788,6 +788,58 @@ static s32 e1000_init_mac_params_ich8lan(struct e1000_hw *hw)
 	return 0;
 }
 
+/**
+ *  __e1000_access_emi_reg_locked - Read/write EMI register
+ *  @hw: pointer to the HW structure
+ *  @addr: EMI address to program
+ *  @data: pointer to value to read/write from/to the EMI address
+ *  @read: boolean flag to indicate read or write
+ *
+ *  This helper function assumes the SW/FW/HW Semaphore is already acquired.
+ **/
+static s32 __e1000_access_emi_reg_locked(struct e1000_hw *hw, u16 address,
+					 u16 *data, bool read)
+{
+	s32 ret_val = 0;
+
+	ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR, address);
+	if (ret_val)
+		return ret_val;
+
+	if (read)
+		ret_val = e1e_rphy_locked(hw, I82579_EMI_DATA, data);
+	else
+		ret_val = e1e_wphy_locked(hw, I82579_EMI_DATA, *data);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_read_emi_reg_locked - Read Extended Management Interface register
+ *  @hw: pointer to the HW structure
+ *  @addr: EMI address to program
+ *  @data: value to be read from the EMI address
+ *
+ *  Assumes the SW/FW/HW Semaphore is already acquired.
+ **/
+static s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data)
+{
+	return __e1000_access_emi_reg_locked(hw, addr, data, true);
+}
+
+/**
+ *  e1000_write_emi_reg_locked - Write Extended Management Interface register
+ *  @hw: pointer to the HW structure
+ *  @addr: EMI address to program
+ *  @data: value to be written to the EMI address
+ *
+ *  Assumes the SW/FW/HW Semaphore is already acquired.
+ **/
+static s32 e1000_write_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 data)
+{
+	return __e1000_access_emi_reg_locked(hw, addr, &data, false);
+}
+
 /**
  *  e1000_set_eee_pchlan - Enable/disable EEE support
  *  @hw: pointer to the HW structure
@@ -823,11 +875,11 @@ static s32 e1000_set_eee_pchlan(struct e1000_hw *hw)
 		ret_val = hw->phy.ops.acquire(hw);
 		if (ret_val)
 			return ret_val;
-		ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR,
-					  I217_EEE_LP_ABILITY);
+		ret_val = e1000_read_emi_reg_locked(hw,
+						    I217_EEE_LP_ABILITY,
+						    &dev_spec->eee_lp_ability);
 		if (ret_val)
 			goto release;
-		e1e_rphy_locked(hw, I82579_EMI_DATA, &dev_spec->eee_lp_ability);
 
 		/* EEE is not supported in 100Half, so ignore partner's EEE
 		 * in 100 ability if full-duplex is not advertised.
@@ -1987,18 +2039,12 @@ static s32 e1000_lv_phy_workarounds_ich8lan(struct e1000_hw *hw)
 	ret_val = hw->phy.ops.acquire(hw);
 	if (ret_val)
 		return ret_val;
-	ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR, I82579_MSE_THRESHOLD);
-	if (ret_val)
-		goto release;
 	/* set MSE higher to enable link to stay up when noise is high */
-	ret_val = e1e_wphy_locked(hw, I82579_EMI_DATA, 0x0034);
-	if (ret_val)
-		goto release;
-	ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR, I82579_MSE_LINK_DOWN);
+	ret_val = e1000_write_emi_reg_locked(hw, I82579_MSE_THRESHOLD, 0x0034);
 	if (ret_val)
 		goto release;
 	/* drop link after 5 times MSE threshold was reached */
-	ret_val = e1e_wphy_locked(hw, I82579_EMI_DATA, 0x0005);
+	ret_val = e1000_write_emi_reg_locked(hw, I82579_MSE_LINK_DOWN, 0x0005);
 release:
 	hw->phy.ops.release(hw);
 
@@ -2172,10 +2218,9 @@ static s32 e1000_post_phy_reset_ich8lan(struct e1000_hw *hw)
 		ret_val = hw->phy.ops.acquire(hw);
 		if (ret_val)
 			return ret_val;
-		ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR,
-					  I82579_LPI_UPDATE_TIMER);
-		if (!ret_val)
-			ret_val = e1e_wphy_locked(hw, I82579_EMI_DATA, 0x1387);
+		ret_val = e1000_write_emi_reg_locked(hw,
+						     I82579_LPI_UPDATE_TIMER,
+						     0x1387);
 		hw->phy.ops.release(hw);
 	}
 
@@ -4013,11 +4058,12 @@ void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw)
 		if (!dev_spec->eee_disable) {
 			u16 eee_advert;
 
-			ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR,
-						  I217_EEE_ADVERTISEMENT);
+			ret_val =
+			    e1000_read_emi_reg_locked(hw,
+						      I217_EEE_ADVERTISEMENT,
+						      &eee_advert);
 			if (ret_val)
 				goto release;
-			e1e_rphy_locked(hw, I82579_EMI_DATA, &eee_advert);
 
 			/* Disable LPLU if both link partners support 100BaseT
 			 * EEE and 100Full is advertised on both ends of the
-- 
cgit v1.2.3


From 651fb1026d9c41d6073cffddfaef1aa224d4ea85 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:26:03 +0000
Subject: e1000e: 82577: workaround for link drop issue

When connected to certain switches, the 82577 PHY might drop link
unexpectedly.  Work around the issue by setting the Mean Square Error
higher than the hardware default.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 8004d7113c39..a7d6c87ebc24 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -157,7 +157,8 @@
 #define I82579_EMI_ADDR         0x10
 #define I82579_EMI_DATA         0x11
 #define I82579_LPI_UPDATE_TIMER 0x4805	/* in 40ns units + 40 ns base value */
-#define I82579_MSE_THRESHOLD    0x084F	/* Mean Square Error Threshold */
+#define I82579_MSE_THRESHOLD    0x084F	/* 82579 Mean Square Error Threshold */
+#define I82577_MSE_THRESHOLD    0x0887	/* 82577 Mean Square Error Threshold */
 #define I82579_MSE_LINK_DOWN    0x2411	/* MSE count before dropping link */
 #define I217_EEE_ADVERTISEMENT  0x8001	/* IEEE MMD Register 7.60 */
 #define I217_EEE_LP_ABILITY     0x8002	/* IEEE MMD Register 7.61 */
@@ -1809,6 +1810,11 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw)
 	if (ret_val)
 		goto release;
 	ret_val = e1e_wphy_locked(hw, BM_PORT_GEN_CFG, phy_data & 0x00FF);
+	if (ret_val)
+		goto release;
+
+	/* set MSE higher to enable link to stay up when noise is high */
+	ret_val = e1000_write_emi_reg_locked(hw, I82577_MSE_THRESHOLD, 0x0034);
 release:
 	hw->phy.ops.release(hw);
 
-- 
cgit v1.2.3


From 3d4d5755f1f1ff27f7f050f07758ae2e7a1256da Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:26:08 +0000
Subject: e1000e: fix enabling of EEE on 82579 and I217

Energy Efficient Ethernet on 82579 and I217 should only be enabled if not
disabled by the user, if the link is full duplex and the link partner has
similar EEE capabilities (stored in different EMI registers on the two
different parts).

After enabling EEE, read the IEEE MMD register 3.1 (which is also stored in
different EMI registers on the two different parts) to clear the count of
received Tx/Rx LPI indications.

Also, rename I217_EEE_100_SUPPORTED to I82579_EEE_100_SUPPORTED to indicate
the bit is valid starting with I82579 (released before I217).

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 94 ++++++++++++++++++++---------
 1 file changed, 65 insertions(+), 29 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index a7d6c87ebc24..15d93141cc11 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -150,6 +150,8 @@
 
 /* PHY Low Power Idle Control */
 #define I82579_LPI_CTRL				PHY_REG(772, 20)
+#define I82579_LPI_CTRL_100_ENABLE		0x2000
+#define I82579_LPI_CTRL_1000_ENABLE		0x4000
 #define I82579_LPI_CTRL_ENABLE_MASK		0x6000
 #define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
 
@@ -160,9 +162,13 @@
 #define I82579_MSE_THRESHOLD    0x084F	/* 82579 Mean Square Error Threshold */
 #define I82577_MSE_THRESHOLD    0x0887	/* 82577 Mean Square Error Threshold */
 #define I82579_MSE_LINK_DOWN    0x2411	/* MSE count before dropping link */
+#define I82579_EEE_PCS_STATUS	0x182D	/* IEEE MMD Register 3.1 >> 8 */
+#define I82579_EEE_LP_ABILITY	0x040F	/* IEEE MMD Register 7.61 */
+#define I82579_EEE_100_SUPPORTED	(1 << 1) /* 100BaseTx EEE supported */
+#define I82579_EEE_1000_SUPPORTED	(1 << 2) /* 1000BaseTx EEE supported */
+#define I217_EEE_PCS_STATUS	0x9401	/* IEEE MMD Register 3.1 */
 #define I217_EEE_ADVERTISEMENT  0x8001	/* IEEE MMD Register 7.60 */
 #define I217_EEE_LP_ABILITY     0x8002	/* IEEE MMD Register 7.61 */
-#define I217_EEE_100_SUPPORTED  (1 << 1)	/* 100BaseTx EEE supported */
 
 /* Intel Rapid Start Technology Support */
 #define I217_PROXY_CTRL                 BM_PHY_REG(BM_WUC_PAGE, 70)
@@ -845,54 +851,84 @@ static s32 e1000_write_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 data)
  *  e1000_set_eee_pchlan - Enable/disable EEE support
  *  @hw: pointer to the HW structure
  *
- *  Enable/disable EEE based on setting in dev_spec structure.  The bits in
- *  the LPI Control register will remain set only if/when link is up.
+ *  Enable/disable EEE based on setting in dev_spec structure, the duplex of
+ *  the link and the EEE capabilities of the link partner.  The LPI Control
+ *  register bits will remain set only if/when link is up.
  **/
 static s32 e1000_set_eee_pchlan(struct e1000_hw *hw)
 {
 	struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
-	s32 ret_val = 0;
-	u16 phy_reg;
+	s32 ret_val;
+	u16 lpi_ctrl;
 
 	if ((hw->phy.type != e1000_phy_82579) &&
 	    (hw->phy.type != e1000_phy_i217))
 		return 0;
 
-	ret_val = e1e_rphy(hw, I82579_LPI_CTRL, &phy_reg);
+	ret_val = hw->phy.ops.acquire(hw);
 	if (ret_val)
 		return ret_val;
 
-	if (dev_spec->eee_disable)
-		phy_reg &= ~I82579_LPI_CTRL_ENABLE_MASK;
-	else
-		phy_reg |= I82579_LPI_CTRL_ENABLE_MASK;
-
-	ret_val = e1e_wphy(hw, I82579_LPI_CTRL, phy_reg);
+	ret_val = e1e_rphy_locked(hw, I82579_LPI_CTRL, &lpi_ctrl);
 	if (ret_val)
-		return ret_val;
+		goto release;
+
+	/* Clear bits that enable EEE in various speeds */
+	lpi_ctrl &= ~I82579_LPI_CTRL_ENABLE_MASK;
+
+	/* Enable EEE if not disabled by user */
+	if (!dev_spec->eee_disable) {
+		u16 lpa, pcs_status, data;
 
-	if ((hw->phy.type == e1000_phy_i217) && !dev_spec->eee_disable) {
 		/* Save off link partner's EEE ability */
-		ret_val = hw->phy.ops.acquire(hw);
-		if (ret_val)
-			return ret_val;
-		ret_val = e1000_read_emi_reg_locked(hw,
-						    I217_EEE_LP_ABILITY,
+		switch (hw->phy.type) {
+		case e1000_phy_82579:
+			lpa = I82579_EEE_LP_ABILITY;
+			pcs_status = I82579_EEE_PCS_STATUS;
+			break;
+		case e1000_phy_i217:
+			lpa = I217_EEE_LP_ABILITY;
+			pcs_status = I217_EEE_PCS_STATUS;
+			break;
+		default:
+			ret_val = -E1000_ERR_PHY;
+			goto release;
+		}
+		ret_val = e1000_read_emi_reg_locked(hw, lpa,
 						    &dev_spec->eee_lp_ability);
 		if (ret_val)
 			goto release;
 
-		/* EEE is not supported in 100Half, so ignore partner's EEE
-		 * in 100 ability if full-duplex is not advertised.
+		/* Enable EEE only for speeds in which the link partner is
+		 * EEE capable.
 		 */
-		e1e_rphy_locked(hw, PHY_LP_ABILITY, &phy_reg);
-		if (!(phy_reg & NWAY_LPAR_100TX_FD_CAPS))
-			dev_spec->eee_lp_ability &= ~I217_EEE_100_SUPPORTED;
-release:
-		hw->phy.ops.release(hw);
+		if (dev_spec->eee_lp_ability & I82579_EEE_1000_SUPPORTED)
+			lpi_ctrl |= I82579_LPI_CTRL_1000_ENABLE;
+
+		if (dev_spec->eee_lp_ability & I82579_EEE_100_SUPPORTED) {
+			e1e_rphy_locked(hw, PHY_LP_ABILITY, &data);
+			if (data & NWAY_LPAR_100TX_FD_CAPS)
+				lpi_ctrl |= I82579_LPI_CTRL_100_ENABLE;
+			else
+				/* EEE is not supported in 100Half, so ignore
+				 * partner's EEE in 100 ability if full-duplex
+				 * is not advertised.
+				 */
+				dev_spec->eee_lp_ability &=
+				    ~I82579_EEE_100_SUPPORTED;
+		}
+
+		/* R/Clr IEEE MMD 3.1 bits 11:10 - Tx/Rx LPI Received */
+		ret_val = e1000_read_emi_reg_locked(hw, pcs_status, &data);
+		if (ret_val)
+			goto release;
 	}
 
-	return 0;
+	ret_val = e1e_wphy_locked(hw, I82579_LPI_CTRL, lpi_ctrl);
+release:
+	hw->phy.ops.release(hw);
+
+	return ret_val;
 }
 
 /**
@@ -4075,9 +4111,9 @@ void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw)
 			 * EEE and 100Full is advertised on both ends of the
 			 * link.
 			 */
-			if ((eee_advert & I217_EEE_100_SUPPORTED) &&
+			if ((eee_advert & I82579_EEE_100_SUPPORTED) &&
 			    (dev_spec->eee_lp_ability &
-			     I217_EEE_100_SUPPORTED) &&
+			     I82579_EEE_100_SUPPORTED) &&
 			    (hw->phy.autoneg_advertised & ADVERTISE_100_FULL))
 				phy_ctrl &= ~(E1000_PHY_CTRL_D0A_LPLU |
 					      E1000_PHY_CTRL_NOND0A_LPLU);
-- 
cgit v1.2.3


From 12d43f7d3cd36494a442dea6f2d2c7ccb76d0d80 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:26:14 +0000
Subject: e1000e: unexpected "Reset adapter" message when cable pulled

When there is heavy traffic and the cable is pulled, the driver must reset
the adapter to flush the Tx queue in hardware.  This causes the reset path
to be scheduled and logs the message "Reset adapter" which could be mis-
interpreted as an error by the user.  Change how the reset path is invoked
for this scenario by using the same method done in an existing work-around
for 80003es2lan (i.e. set a flag and if the flag is set in the reset code
do not log the "Reset adapter" message since the reset is expected).

Re-name the FLAG_RX_RESTART_NOW to FLAG_RESTART_NOW since it is used for
resets in both the Rx and Tx specific code.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/e1000.h  |  2 +-
 drivers/net/ethernet/intel/e1000e/netdev.c | 39 +++++++++++++++---------------
 2 files changed, 21 insertions(+), 20 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 6782a2eea1bc..3f8bbc31795c 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -447,7 +447,7 @@ struct e1000_info {
 #define FLAG_MSI_ENABLED                  (1 << 27)
 /* reserved (1 << 28) */
 #define FLAG_TSO_FORCE                    (1 << 29)
-#define FLAG_RX_RESTART_NOW               (1 << 30)
+#define FLAG_RESTART_NOW                  (1 << 30)
 #define FLAG_MSI_TEST_FAILED              (1 << 31)
 
 #define FLAG2_CRC_STRIPPING               (1 << 0)
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 337644dda14d..7ad8ef639cea 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -1671,7 +1671,7 @@ static irqreturn_t e1000_intr_msi(int irq, void *data)
 			/* disable receives */
 			u32 rctl = er32(RCTL);
 			ew32(RCTL, rctl & ~E1000_RCTL_EN);
-			adapter->flags |= FLAG_RX_RESTART_NOW;
+			adapter->flags |= FLAG_RESTART_NOW;
 		}
 		/* guard against interrupt when we're going down */
 		if (!test_bit(__E1000_DOWN, &adapter->state))
@@ -1734,7 +1734,7 @@ static irqreturn_t e1000_intr(int irq, void *data)
 			/* disable receives */
 			rctl = er32(RCTL);
 			ew32(RCTL, rctl & ~E1000_RCTL_EN);
-			adapter->flags |= FLAG_RX_RESTART_NOW;
+			adapter->flags |= FLAG_RESTART_NOW;
 		}
 		/* guard against interrupt when we're going down */
 		if (!test_bit(__E1000_DOWN, &adapter->state))
@@ -3013,7 +3013,7 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 
 	ew32(RCTL, rctl);
 	/* just started the receive unit, no need to restart */
-	adapter->flags &= ~FLAG_RX_RESTART_NOW;
+	adapter->flags &= ~FLAG_RESTART_NOW;
 }
 
 /**
@@ -4355,11 +4355,11 @@ static void e1000e_enable_receives(struct e1000_adapter *adapter)
 {
 	/* make sure the receive unit is started */
 	if ((adapter->flags & FLAG_RX_NEEDS_RESTART) &&
-	    (adapter->flags & FLAG_RX_RESTART_NOW)) {
+	    (adapter->flags & FLAG_RESTART_NOW)) {
 		struct e1000_hw *hw = &adapter->hw;
 		u32 rctl = er32(RCTL);
 		ew32(RCTL, rctl | E1000_RCTL_EN);
-		adapter->flags &= ~FLAG_RX_RESTART_NOW;
+		adapter->flags &= ~FLAG_RESTART_NOW;
 	}
 }
 
@@ -4528,8 +4528,16 @@ static void e1000_watchdog_task(struct work_struct *work)
 				mod_timer(&adapter->phy_info_timer,
 					  round_jiffies(jiffies + 2 * HZ));
 
-			if (adapter->flags & FLAG_RX_NEEDS_RESTART)
-				schedule_work(&adapter->reset_task);
+			/* The link is lost so the controller stops DMA.
+			 * If there is queued Tx work that cannot be done
+			 * or if on an 8000ES2LAN which requires a Rx packet
+			 * buffer work-around on link down event, reset the
+			 * controller to flush the Tx/Rx packet buffers.
+			 * (Do the reset outside of interrupt context).
+			 */
+			if ((adapter->flags & FLAG_RX_NEEDS_RESTART) ||
+			    (e1000_desc_unused(tx_ring) + 1 < tx_ring->count))
+				adapter->flags |= FLAG_RESTART_NOW;
 			else
 				pm_schedule_suspend(netdev->dev.parent,
 							LINK_TIMEOUT);
@@ -4551,20 +4559,14 @@ link_up:
 	adapter->gotc_old = adapter->stats.gotc;
 	spin_unlock(&adapter->stats64_lock);
 
-	e1000e_update_adaptive(&adapter->hw);
-
-	if (!netif_carrier_ok(netdev) &&
-	    (e1000_desc_unused(tx_ring) + 1 < tx_ring->count)) {
-		/* We've lost link, so the controller stops DMA,
-		 * but we've got queued Tx work that's never going
-		 * to get done, so reset controller to flush Tx.
-		 * (Do the reset outside of interrupt context).
-		 */
+	if (adapter->flags & FLAG_RESTART_NOW) {
 		schedule_work(&adapter->reset_task);
 		/* return immediately since reset is imminent */
 		return;
 	}
 
+	e1000e_update_adaptive(&adapter->hw);
+
 	/* Simple mode for Interrupt Throttle Rate (ITR) */
 	if (adapter->itr_setting == 4) {
 		/* Symmetric Tx/Rx gets a reduced ITR=2000;
@@ -5134,10 +5136,9 @@ static void e1000_reset_task(struct work_struct *work)
 	if (test_bit(__E1000_DOWN, &adapter->state))
 		return;
 
-	if (!((adapter->flags & FLAG_RX_NEEDS_RESTART) &&
-	      (adapter->flags & FLAG_RX_RESTART_NOW))) {
+	if (!(adapter->flags & FLAG_RESTART_NOW)) {
 		e1000e_dump(adapter);
-		e_err("Reset adapter\n");
+		e_err("Reset adapter unexpectedly\n");
 	}
 	e1000e_reinit_locked(adapter);
 }
-- 
cgit v1.2.3


From 8e5ab42d7fdd73b11a6b6b58b4a7b26931c73385 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:26:19 +0000
Subject: e1000e: add missing bailout on error

...discovered during code inspection.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 2 ++
 1 file changed, 2 insertions(+)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 15d93141cc11..051dfda75fc0 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -2077,6 +2077,8 @@ static s32 e1000_lv_phy_workarounds_ich8lan(struct e1000_hw *hw)
 
 	/* Set MDIO slow mode before any other MDIO access */
 	ret_val = e1000_set_mdio_slow_mode_hv(hw);
+	if (ret_val)
+		return ret_val;
 
 	ret_val = hw->phy.ops.acquire(hw);
 	if (ret_val)
-- 
cgit v1.2.3


From 7dbc1672f155958e2f548a29caea709a136ed0f2 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 03:11:25 +0000
Subject: e1000e: resolve checkpatch PREFER_PR_LEVEL warning

WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
then pr_info(...  to printk(KERN_INFO ...

v2 - remove unnecessary "e1000e:" prefix as pointed out by Joe Perches
     since that produces a redundant "e1000e:" in the log message

Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 7ad8ef639cea..b22eb049e27d 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -4300,9 +4300,8 @@ static void e1000_print_link_info(struct e1000_adapter *adapter)
 	u32 ctrl = er32(CTRL);
 
 	/* Link status message must follow this format for user tools */
-	printk(KERN_INFO "e1000e: %s NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n",
-		adapter->netdev->name,
-		adapter->link_speed,
+	pr_info("%s NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n",
+		adapter->netdev->name, adapter->link_speed,
 		adapter->link_duplex == FULL_DUPLEX ? "Full" : "Half",
 		(ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE) ? "Rx/Tx" :
 		(ctrl & E1000_CTRL_RFCE) ? "Rx" :
@@ -4521,8 +4520,7 @@ static void e1000_watchdog_task(struct work_struct *work)
 			adapter->link_speed = 0;
 			adapter->link_duplex = 0;
 			/* Link status message must follow this format */
-			printk(KERN_INFO "e1000e: %s NIC Link is Down\n",
-			       adapter->netdev->name);
+			pr_info("%s NIC Link is Down\n", adapter->netdev->name);
 			netif_carrier_off(netdev);
 			if (!test_bit(__E1000_DOWN, &adapter->state))
 				mod_timer(&adapter->phy_info_timer,
-- 
cgit v1.2.3


From 0a939912cf9cbc088e01a7c9493ef5791a881075 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:26:30 +0000
Subject: e1000e: cleanup redundant statistics counter

rx_long_byte_count can be removed since it is duplicated in rx_bytes

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ethtool.c | 1 -
 1 file changed, 1 deletion(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index f95bc6ee1c22..2225603a8a28 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -98,7 +98,6 @@ static const struct e1000_stats e1000_gstrings_stats[] = {
 	E1000_STAT("rx_flow_control_xoff", stats.xoffrxc),
 	E1000_STAT("tx_flow_control_xon", stats.xontxc),
 	E1000_STAT("tx_flow_control_xoff", stats.xofftxc),
-	E1000_STAT("rx_long_byte_count", stats.gorc),
 	E1000_STAT("rx_csum_offload_good", hw_csum_good),
 	E1000_STAT("rx_csum_offload_errors", hw_csum_err),
 	E1000_STAT("rx_header_split", rx_hdr_split),
-- 
cgit v1.2.3


From 2a2293b9510f05f963422121109b8ec3b9ee9f9f Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:26:35 +0000
Subject: e1000e: cleanup unusual comment placement

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index b22eb049e27d..18790a608f4f 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -765,7 +765,7 @@ static void e1000_alloc_jumbo_rx_buffers(struct e1000_ring *rx_ring,
 	struct e1000_buffer *buffer_info;
 	struct sk_buff *skb;
 	unsigned int i;
-	unsigned int bufsz = 256 - 16 /* for skb_reserve */;
+	unsigned int bufsz = 256 - 16;	/* for skb_reserve */
 
 	i = rx_ring->next_to_use;
 	buffer_info = &rx_ring->buffer_info[i];
-- 
cgit v1.2.3


From 1860ac84613877f9ec8a1235e04190e26dd06514 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:26:40 +0000
Subject: e1000e: cleanup unnecessary line wrap

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/param.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/param.c b/drivers/net/ethernet/intel/e1000e/param.c
index 89d536dd7ff5..b29a8a5116a8 100644
--- a/drivers/net/ethernet/intel/e1000e/param.c
+++ b/drivers/net/ethernet/intel/e1000e/param.c
@@ -447,8 +447,7 @@ void e1000e_check_options(struct e1000_adapter *adapter)
 		if (num_SmartPowerDownEnable > bd) {
 			unsigned int spd = SmartPowerDownEnable[bd];
 			e1000_validate_option(&spd, &opt, adapter);
-			if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN)
-			    && spd)
+			if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN) && spd)
 				adapter->flags |= FLAG_SMART_POWER_DOWN;
 		}
 	}
-- 
cgit v1.2.3


From 3a3104e7d022ec24862448d167a21de46accf6e8 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:26:46 +0000
Subject: e1000e: cleanup magic number

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/nvm.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/nvm.c b/drivers/net/ethernet/intel/e1000e/nvm.c
index 71938ed2d3c3..1e7882c7d6d4 100644
--- a/drivers/net/ethernet/intel/e1000e/nvm.c
+++ b/drivers/net/ethernet/intel/e1000e/nvm.c
@@ -464,8 +464,8 @@ s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
 	if (nvm_data != NVM_PBA_PTR_GUARD) {
 		e_dbg("NVM PBA number is not stored as string\n");
 
-		/* we will need 11 characters to store the PBA */
-		if (pba_num_size < 11) {
+		/* make sure callers buffer is big enough to store the PBA */
+		if (pba_num_size < E1000_PBANUM_LENGTH) {
 			e_dbg("PBA string buffer too small\n");
 			return E1000_ERR_NO_SPACE;
 		}
-- 
cgit v1.2.3


From e3d14b08e80744958af920ab8bc8ee3866c3902b Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:26:51 +0000
Subject: e1000e: cleanup code duplication

The removed code block is duplicated in e1000e_write_itr() so use that
instead.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 6 +-----
 1 file changed, 1 insertion(+), 5 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 18790a608f4f..6aa9c5d31a48 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -2405,7 +2405,6 @@ static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
 
 static void e1000_set_itr(struct e1000_adapter *adapter)
 {
-	struct e1000_hw *hw = &adapter->hw;
 	u16 current_itr;
 	u32 new_itr = adapter->itr;
 
@@ -2468,10 +2467,7 @@ set_itr_now:
 		if (adapter->msix_entries)
 			adapter->rx_ring->set_itr = 1;
 		else
-			if (new_itr)
-				ew32(ITR, 1000000000 / (new_itr * 256));
-			else
-				ew32(ITR, 0);
+			e1000e_write_itr(adapter, new_itr);
 	}
 }
 
-- 
cgit v1.2.3


From d60923c465809cec44fb08c53da6cf0c53040dc1 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:26:56 +0000
Subject: e1000e: merge multiple conditional statements into one

Cleanup a set of conditional tests.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 11 +++++------
 1 file changed, 5 insertions(+), 6 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 6aa9c5d31a48..05538e66c809 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -4914,12 +4914,11 @@ static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter,
 	struct e1000_hw *hw =  &adapter->hw;
 	u16 length, offset;
 
-	if (vlan_tx_tag_present(skb)) {
-		if (!((vlan_tx_tag_get(skb) == adapter->hw.mng_cookie.vlan_id) &&
-		    (adapter->hw.mng_cookie.status &
-			E1000_MNG_DHCP_COOKIE_STATUS_VLAN)))
-			return 0;
-	}
+	if (vlan_tx_tag_present(skb) &&
+	    !((vlan_tx_tag_get(skb) == adapter->hw.mng_cookie.vlan_id) &&
+	      (adapter->hw.mng_cookie.status &
+	       E1000_MNG_DHCP_COOKIE_STATUS_VLAN)))
+		return 0;
 
 	if (skb->len <= MINIMUM_DHCP_PACKET_SIZE)
 		return 0;
-- 
cgit v1.2.3


From 203e41514a557b71c4c42b4bb2912b56fa0c2fdc Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 08:40:59 +0000
Subject: e1000e: add ethtool .get_eee/.set_eee

Add the ability to query and set Energy Efficient Ethernet parameters via
ethtool for applicable devices.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  30 +++++++
 drivers/net/ethernet/intel/e1000e/e1000.h   |   1 +
 drivers/net/ethernet/intel/e1000e/ethtool.c | 134 ++++++++++++++++++++++++++++
 drivers/net/ethernet/intel/e1000e/hw.h      |   1 +
 drivers/net/ethernet/intel/e1000e/ich8lan.c |  24 +----
 5 files changed, 167 insertions(+), 23 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 7326ea2fef8f..3041a54e3a61 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -383,6 +383,9 @@
 
 #define E1000_KABGTXD_BGSQLBIAS           0x00050000
 
+/* Low Power IDLE Control */
+#define E1000_LPIC_LPIET_SHIFT		24	/* Low Power Idle Entry Time */
+
 /* PBA constants */
 #define E1000_PBA_8K  0x0008    /* 8KB */
 #define E1000_PBA_16K 0x0010    /* 16KB */
@@ -799,6 +802,33 @@
 /* BME1000 PHY Specific Control Register */
 #define BME1000_PSCR_ENABLE_DOWNSHIFT   0x0800 /* 1 = enable downshift */
 
+/* PHY Low Power Idle Control */
+#define I82579_LPI_CTRL				PHY_REG(772, 20)
+#define I82579_LPI_CTRL_100_ENABLE		0x2000
+#define I82579_LPI_CTRL_1000_ENABLE		0x4000
+#define I82579_LPI_CTRL_ENABLE_MASK		0x6000
+#define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
+
+/* Extended Management Interface (EMI) Registers */
+#define I82579_EMI_ADDR		0x10
+#define I82579_EMI_DATA		0x11
+#define I82579_LPI_UPDATE_TIMER	0x4805	/* in 40ns units + 40 ns base value */
+#define I82579_MSE_THRESHOLD	0x084F	/* 82579 Mean Square Error Threshold */
+#define I82577_MSE_THRESHOLD	0x0887	/* 82577 Mean Square Error Threshold */
+#define I82579_MSE_LINK_DOWN	0x2411	/* MSE count before dropping link */
+#define I82579_EEE_PCS_STATUS	0x182D	/* IEEE MMD Register 3.1 >> 8 */
+#define I82579_EEE_CAPABILITY	0x0410	/* IEEE MMD Register 3.20 */
+#define I82579_EEE_ADVERTISEMENT	0x040E	/* IEEE MMD Register 7.60 */
+#define I82579_EEE_LP_ABILITY		0x040F	/* IEEE MMD Register 7.61 */
+#define I82579_EEE_100_SUPPORTED	(1 << 1) /* 100BaseTx EEE supported */
+#define I82579_EEE_1000_SUPPORTED	(1 << 2) /* 1000BaseTx EEE supported */
+#define I217_EEE_PCS_STATUS	0x9401	/* IEEE MMD Register 3.1 */
+#define I217_EEE_CAPABILITY	0x8000	/* IEEE MMD Register 3.20 */
+#define I217_EEE_ADVERTISEMENT	0x8001	/* IEEE MMD Register 7.60 */
+#define I217_EEE_LP_ABILITY	0x8002	/* IEEE MMD Register 7.61 */
+
+#define E1000_EEE_RX_LPI_RCVD	0x0400	/* Tx LP idle received */
+#define E1000_EEE_TX_LPI_RCVD	0x0800	/* Rx LP idle received */
 
 #define PHY_PAGE_SHIFT 5
 #define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 3f8bbc31795c..b89b181da7b1 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -659,6 +659,7 @@ extern s32 e1000_check_polarity_ife(struct e1000_hw *hw);
 extern s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_igp(struct e1000_hw *hw);
 extern bool e1000_check_phy_82574(struct e1000_hw *hw);
+extern s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
 
 static inline s32 e1000_phy_hw_reset(struct e1000_hw *hw)
 {
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 2225603a8a28..636ba09ca6fb 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -35,6 +35,7 @@
 #include <linux/slab.h>
 #include <linux/delay.h>
 #include <linux/vmalloc.h>
+#include <linux/mdio.h>
 
 #include "e1000.h"
 
@@ -2050,6 +2051,137 @@ static int e1000_get_rxnfc(struct net_device *netdev,
 	}
 }
 
+static int e1000e_get_eee(struct net_device *netdev, struct ethtool_eee *edata)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+	struct e1000_hw *hw = &adapter->hw;
+	u16 cap_addr, adv_addr, lpa_addr, pcs_stat_addr, phy_data, lpi_ctrl;
+	u32 status, ret_val;
+
+	if (!(adapter->flags & FLAG_IS_ICH) ||
+	    !(adapter->flags2 & FLAG2_HAS_EEE))
+		return -EOPNOTSUPP;
+
+	switch (hw->phy.type) {
+	case e1000_phy_82579:
+		cap_addr = I82579_EEE_CAPABILITY;
+		adv_addr = I82579_EEE_ADVERTISEMENT;
+		lpa_addr = I82579_EEE_LP_ABILITY;
+		pcs_stat_addr = I82579_EEE_PCS_STATUS;
+		break;
+	case e1000_phy_i217:
+		cap_addr = I217_EEE_CAPABILITY;
+		adv_addr = I217_EEE_ADVERTISEMENT;
+		lpa_addr = I217_EEE_LP_ABILITY;
+		pcs_stat_addr = I217_EEE_PCS_STATUS;
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	ret_val = hw->phy.ops.acquire(hw);
+	if (ret_val)
+		return -EBUSY;
+
+	/* EEE Capability */
+	ret_val = e1000_read_emi_reg_locked(hw, cap_addr, &phy_data);
+	if (ret_val)
+		goto release;
+	edata->supported = mmd_eee_cap_to_ethtool_sup_t(phy_data);
+
+	/* EEE Advertised */
+	ret_val = e1000_read_emi_reg_locked(hw, adv_addr, &phy_data);
+	if (ret_val)
+		goto release;
+	edata->advertised = mmd_eee_adv_to_ethtool_adv_t(phy_data);
+
+	/* EEE Link Partner Advertised */
+	ret_val = e1000_read_emi_reg_locked(hw, lpa_addr, &phy_data);
+	if (ret_val)
+		goto release;
+	edata->lp_advertised = mmd_eee_adv_to_ethtool_adv_t(phy_data);
+
+	/* EEE PCS Status */
+	ret_val = e1000_read_emi_reg_locked(hw, pcs_stat_addr, &phy_data);
+	if (hw->phy.type == e1000_phy_82579)
+		phy_data <<= 8;
+
+release:
+	hw->phy.ops.release(hw);
+	if (ret_val)
+		return -ENODATA;
+
+	e1e_rphy(hw, I82579_LPI_CTRL, &lpi_ctrl);
+	status = er32(STATUS);
+
+	/* Result of the EEE auto negotiation - there is no register that
+	 * has the status of the EEE negotiation so do a best-guess based
+	 * on whether both Tx and Rx LPI indications have been received or
+	 * base it on the link speed, the EEE advertised speeds on both ends
+	 * and the speeds on which EEE is enabled locally.
+	 */
+	if (((phy_data & E1000_EEE_TX_LPI_RCVD) &&
+	     (phy_data & E1000_EEE_RX_LPI_RCVD)) ||
+	    ((status & E1000_STATUS_SPEED_100) &&
+	     (edata->advertised & ADVERTISED_100baseT_Full) &&
+	     (edata->lp_advertised & ADVERTISED_100baseT_Full) &&
+	     (lpi_ctrl & I82579_LPI_CTRL_100_ENABLE)) ||
+	    ((status & E1000_STATUS_SPEED_1000) &&
+	     (edata->advertised & ADVERTISED_1000baseT_Full) &&
+	     (edata->lp_advertised & ADVERTISED_1000baseT_Full) &&
+	     (lpi_ctrl & I82579_LPI_CTRL_1000_ENABLE)))
+		edata->eee_active = true;
+
+	edata->eee_enabled = !hw->dev_spec.ich8lan.eee_disable;
+	edata->tx_lpi_enabled = true;
+	edata->tx_lpi_timer = er32(LPIC) >> E1000_LPIC_LPIET_SHIFT;
+
+	return 0;
+}
+
+static int e1000e_set_eee(struct net_device *netdev, struct ethtool_eee *edata)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+	struct e1000_hw *hw = &adapter->hw;
+	struct ethtool_eee eee_curr;
+	s32 ret_val;
+
+	if (!(adapter->flags & FLAG_IS_ICH) ||
+	    !(adapter->flags2 & FLAG2_HAS_EEE))
+		return -EOPNOTSUPP;
+
+	ret_val = e1000e_get_eee(netdev, &eee_curr);
+	if (ret_val)
+		return ret_val;
+
+	if (eee_curr.advertised != edata->advertised) {
+		e_err("Setting EEE advertisement is not supported\n");
+		return -EINVAL;
+	}
+
+	if (eee_curr.tx_lpi_enabled != edata->tx_lpi_enabled) {
+		e_err("Setting EEE tx-lpi is not supported\n");
+		return -EINVAL;
+	}
+
+	if (eee_curr.tx_lpi_timer != edata->tx_lpi_timer) {
+		e_err("Setting EEE Tx LPI timer is not supported\n");
+		return -EINVAL;
+	}
+
+	if (hw->dev_spec.ich8lan.eee_disable != !edata->eee_enabled) {
+		hw->dev_spec.ich8lan.eee_disable = !edata->eee_enabled;
+
+		/* reset the link */
+		if (netif_running(netdev))
+			e1000e_reinit_locked(adapter);
+		else
+			e1000e_reset(adapter);
+	}
+
+	return 0;
+}
+
 static const struct ethtool_ops e1000_ethtool_ops = {
 	.get_settings		= e1000_get_settings,
 	.set_settings		= e1000_set_settings,
@@ -2078,6 +2210,8 @@ static const struct ethtool_ops e1000_ethtool_ops = {
 	.set_coalesce		= e1000_set_coalesce,
 	.get_rxnfc		= e1000_get_rxnfc,
 	.get_ts_info		= ethtool_op_get_ts_info,
+	.get_eee		= e1000e_get_eee,
+	.set_eee		= e1000e_set_eee,
 };
 
 void e1000e_set_ethtool_ops(struct net_device *netdev)
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 06239fe47db1..81afad5b80f2 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -62,6 +62,7 @@ enum e1e_registers {
 	E1000_IVAR     = 0x000E4, /* Interrupt Vector Allocation - RW */
 	E1000_EITR_82574_BASE = 0x000E8, /* Interrupt Throttling - RW */
 #define E1000_EITR_82574(_n) (E1000_EITR_82574_BASE + (_n << 2))
+	E1000_LPIC     = 0x000FC, /* Low Power Idle Control - RW */
 	E1000_RCTL     = 0x00100, /* Rx Control - RW */
 	E1000_FCTTV    = 0x00170, /* Flow Control Transmit Timer Value - RW */
 	E1000_TXCW     = 0x00178, /* Tx Configuration Word - RW */
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 051dfda75fc0..3829f7fd1d97 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -148,28 +148,6 @@
 #define HV_PM_CTRL		PHY_REG(770, 17)
 #define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA	0x100
 
-/* PHY Low Power Idle Control */
-#define I82579_LPI_CTRL				PHY_REG(772, 20)
-#define I82579_LPI_CTRL_100_ENABLE		0x2000
-#define I82579_LPI_CTRL_1000_ENABLE		0x4000
-#define I82579_LPI_CTRL_ENABLE_MASK		0x6000
-#define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
-
-/* Extended Management Interface (EMI) Registers */
-#define I82579_EMI_ADDR         0x10
-#define I82579_EMI_DATA         0x11
-#define I82579_LPI_UPDATE_TIMER 0x4805	/* in 40ns units + 40 ns base value */
-#define I82579_MSE_THRESHOLD    0x084F	/* 82579 Mean Square Error Threshold */
-#define I82577_MSE_THRESHOLD    0x0887	/* 82577 Mean Square Error Threshold */
-#define I82579_MSE_LINK_DOWN    0x2411	/* MSE count before dropping link */
-#define I82579_EEE_PCS_STATUS	0x182D	/* IEEE MMD Register 3.1 >> 8 */
-#define I82579_EEE_LP_ABILITY	0x040F	/* IEEE MMD Register 7.61 */
-#define I82579_EEE_100_SUPPORTED	(1 << 1) /* 100BaseTx EEE supported */
-#define I82579_EEE_1000_SUPPORTED	(1 << 2) /* 1000BaseTx EEE supported */
-#define I217_EEE_PCS_STATUS	0x9401	/* IEEE MMD Register 3.1 */
-#define I217_EEE_ADVERTISEMENT  0x8001	/* IEEE MMD Register 7.60 */
-#define I217_EEE_LP_ABILITY     0x8002	/* IEEE MMD Register 7.61 */
-
 /* Intel Rapid Start Technology Support */
 #define I217_PROXY_CTRL                 BM_PHY_REG(BM_WUC_PAGE, 70)
 #define I217_PROXY_CTRL_AUTO_DISABLE    0x0080
@@ -829,7 +807,7 @@ static s32 __e1000_access_emi_reg_locked(struct e1000_hw *hw, u16 address,
  *
  *  Assumes the SW/FW/HW Semaphore is already acquired.
  **/
-static s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data)
+s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data)
 {
 	return __e1000_access_emi_reg_locked(hw, addr, data, true);
 }
-- 
cgit v1.2.3


From ffe0b2ff17e1d59d33334767e07e8141de4bd5c8 Mon Sep 17 00:00:00 2001
From: Bjorn Helgaas <bhelgaas@google.com>
Date: Thu, 6 Dec 2012 06:40:07 +0000
Subject: e1000e: Use standard #defines for PCIe Capability ASPM fields

Use the standard #defines for PCIe Capability ASPM fields.

Previously we used PCIE_LINK_STATE_L0S and PCIE_LINK_STATE_L1 directly, but
these are defined for the Linux ASPM interfaces, e.g.,
pci_disable_link_state(), and only coincidentally match the actual register
bits.  PCIE_LINK_STATE_CLKPM, also part of that interface, does not match
the register bit.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: e1000-devel@lists.sourceforge.net
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 05538e66c809..bf2c84cf250f 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -5548,14 +5548,21 @@ static void __e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
 #else
 static void __e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
 {
+	u16 aspm_ctl = 0;
+
+	if (state & PCIE_LINK_STATE_L0S)
+		aspm_ctl |= PCI_EXP_LNKCTL_ASPM_L0S;
+	if (state & PCIE_LINK_STATE_L1)
+		aspm_ctl |= PCI_EXP_LNKCTL_ASPM_L1;
+
 	/* Both device and parent should have the same ASPM setting.
 	 * Disable ASPM in downstream component first and then upstream.
 	 */
-	pcie_capability_clear_word(pdev, PCI_EXP_LNKCTL, state);
+	pcie_capability_clear_word(pdev, PCI_EXP_LNKCTL, aspm_ctl);
 
 	if (pdev->bus->self)
 		pcie_capability_clear_word(pdev->bus->self, PCI_EXP_LNKCTL,
-					   state);
+					   aspm_ctl);
 }
 #endif
 static void e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
-- 
cgit v1.2.3


From b67e191307a3f330525265af3e2877a74d557cbf Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Thu, 27 Dec 2012 08:32:33 +0000
Subject: e1000e: add support for hardware timestamping on some devices

On 82574, 82583, 82579, I217 and I218 add support for hardware time
stamping of all or no Rx packets and Tx packets which have the
SKBTX_HW_TSTAMP flag set.  Update the .get_ts_info ethtool operation to
report the supported time stamping modes, and enable and disable hardware
time stamping with the SIOCSHWTSTAMP ioctl.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/82571.c   |   2 +
 drivers/net/ethernet/intel/e1000e/defines.h |  14 ++
 drivers/net/ethernet/intel/e1000e/e1000.h   |  46 +++-
 drivers/net/ethernet/intel/e1000e/ethtool.c |  25 +-
 drivers/net/ethernet/intel/e1000e/hw.h      |  10 +
 drivers/net/ethernet/intel/e1000e/ich8lan.c |   2 +
 drivers/net/ethernet/intel/e1000e/netdev.c  | 371 +++++++++++++++++++++++++++-
 7 files changed, 462 insertions(+), 8 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index c77d010d5c59..587890d2d55e 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -2044,6 +2044,7 @@ const struct e1000_info e1000_82574_info = {
 				  | FLAG_HAS_MSIX
 				  | FLAG_HAS_JUMBO_FRAMES
 				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_APME_IN_CTRL3
 				  | FLAG_HAS_SMART_POWER_DOWN
 				  | FLAG_HAS_AMT
@@ -2065,6 +2066,7 @@ const struct e1000_info e1000_82583_info = {
 	.mac			= e1000_82583,
 	.flags			= FLAG_HAS_HW_VLAN_FILTER
 				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_APME_IN_CTRL3
 				  | FLAG_HAS_SMART_POWER_DOWN
 				  | FLAG_HAS_AMT
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 3041a54e3a61..36f9fad19a76 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -107,6 +107,7 @@
 #define E1000_RXD_ERR_RXE       0x80    /* Rx Data Error */
 #define E1000_RXD_SPC_VLAN_MASK 0x0FFF  /* VLAN ID is in lower 12 bits */
 
+#define E1000_RXDEXT_STATERR_TST   0x00000100	/* Time Stamp taken */
 #define E1000_RXDEXT_STATERR_CE    0x01000000
 #define E1000_RXDEXT_STATERR_SE    0x02000000
 #define E1000_RXDEXT_STATERR_SEQ   0x04000000
@@ -318,6 +319,7 @@
 #define E1000_TXD_CMD_IP     0x02000000 /* IP packet */
 #define E1000_TXD_CMD_TSE    0x04000000 /* TCP Seg enable */
 #define E1000_TXD_STAT_TC    0x00000004 /* Tx Underrun */
+#define E1000_TXD_EXTCMD_TSTAMP	0x00000010 /* IEEE1588 Timestamp packet */
 
 /* Transmit Control */
 #define E1000_TCTL_EN     0x00000002    /* enable Tx */
@@ -536,6 +538,18 @@
 #define E1000_RXCW_C          0x20000000        /* Receive config */
 #define E1000_RXCW_SYNCH      0x40000000        /* Receive config synch */
 
+#define E1000_TSYNCTXCTL_VALID		0x00000001 /* Tx timestamp valid */
+#define E1000_TSYNCRXCTL_TYPE_ALL	0x08
+#define E1000_TSYNCTXCTL_ENABLED	0x00000010 /* enable Tx timestamping */
+
+#define E1000_TSYNCRXCTL_VALID		0x00000001 /* Rx timestamp valid */
+#define E1000_TSYNCRXCTL_TYPE_MASK	0x0000000E /* Rx type mask */
+#define E1000_TSYNCRXCTL_ENABLED	0x00000010 /* enable Rx timestamping */
+#define E1000_TSYNCRXCTL_SYSCFI		0x00000020 /* Sys clock frequency */
+
+#define E1000_TIMINCA_INCPERIOD_SHIFT	24
+#define E1000_TIMINCA_INCVALUE_MASK	0x00FFFFFF
+
 /* PCI Express Control */
 #define E1000_GCR_RXD_NO_SNOOP          0x00000001
 #define E1000_GCR_RXDSCW_NO_SNOOP       0x00000002
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index b89b181da7b1..dea9e5552966 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -41,6 +41,8 @@
 #include <linux/pci-aspm.h>
 #include <linux/crc32.h>
 #include <linux/if_vlan.h>
+#include <linux/clocksource.h>
+#include <linux/net_tstamp.h>
 
 #include "hw.h"
 
@@ -353,6 +355,7 @@ struct e1000_adapter {
 	u64 gorc_old;
 	u32 alloc_rx_buff_failed;
 	u32 rx_dma_failed;
+	u32 rx_hwtstamp_cleared;
 
 	unsigned int rx_ps_pages;
 	u16 rx_ps_bsize0;
@@ -402,6 +405,14 @@ struct e1000_adapter {
 
 	u16 tx_ring_count;
 	u16 rx_ring_count;
+
+	struct hwtstamp_config hwtstamp_config;
+	struct delayed_work systim_overflow_work;
+	struct sk_buff *tx_hwtstamp_skb;
+	struct work_struct tx_hwtstamp_work;
+	spinlock_t systim_lock;	/* protects SYSTIML/H regsters */
+	struct cyclecounter cc;
+	struct timecounter tc;
 };
 
 struct e1000_info {
@@ -416,6 +427,38 @@ struct e1000_info {
 	const struct e1000_nvm_operations *nvm_ops;
 };
 
+/* The system time is maintained by a 64-bit counter comprised of the 32-bit
+ * SYSTIMH and SYSTIML registers.  How the counter increments (and therefore
+ * its resolution) is based on the contents of the TIMINCA register - it
+ * increments every incperiod (bits 31:24) clock ticks by incvalue (bits 23:0).
+ * For the best accuracy, the incperiod should be as small as possible.  The
+ * incvalue is scaled by a factor as large as possible (while still fitting
+ * in bits 23:0) so that relatively small clock corrections can be made.
+ *
+ * As a result, a shift of INCVALUE_SHIFT_n is used to fit a value of
+ * INCVALUE_n into the TIMINCA register allowing 32+8+(24-INCVALUE_SHIFT_n)
+ * bits to count nanoseconds leaving the rest for fractional nonseconds.
+ */
+#define INCVALUE_96MHz		125
+#define INCVALUE_SHIFT_96MHz	17
+#define INCPERIOD_SHIFT_96MHz	2
+#define INCPERIOD_96MHz		(12 >> INCPERIOD_SHIFT_96MHz)
+
+#define INCVALUE_25MHz		40
+#define INCVALUE_SHIFT_25MHz	18
+#define INCPERIOD_25MHz		1
+
+/* Another drawback of scaling the incvalue by a large factor is the
+ * 64-bit SYSTIM register overflows more quickly.  This is dealt with
+ * by simply reading the clock before it overflows.
+ *
+ * Clock	ns bits	Overflows after
+ * ~~~~~~	~~~~~~~	~~~~~~~~~~~~~~~
+ * 96MHz	47-bit	2^(47-INCPERIOD_SHIFT_96MHz) / 10^9 / 3600 = 9.77 hrs
+ * 25MHz	46-bit	2^46 / 10^9 / 3600 = 19.55 hours
+ */
+#define E1000_SYSTIM_OVERFLOW_PERIOD	(HZ * 60 * 60 * 4)
+
 /* hardware capability, feature, and workaround flags */
 #define FLAG_HAS_AMT                      (1 << 0)
 #define FLAG_HAS_FLASH                    (1 << 1)
@@ -431,7 +474,7 @@ struct e1000_info {
 #define FLAG_HAS_SMART_POWER_DOWN         (1 << 11)
 #define FLAG_IS_QUAD_PORT_A               (1 << 12)
 #define FLAG_IS_QUAD_PORT                 (1 << 13)
-/* reserved bit14 */
+#define FLAG_HAS_HW_TIMESTAMP             (1 << 14)
 #define FLAG_APME_IN_WUC                  (1 << 15)
 #define FLAG_APME_IN_CTRL3                (1 << 16)
 #define FLAG_APME_CHECK_PORT_B            (1 << 17)
@@ -463,6 +506,7 @@ struct e1000_info {
 #define FLAG2_NO_DISABLE_RX               (1 << 10)
 #define FLAG2_PCIM2PCI_ARBITER_WA         (1 << 11)
 #define FLAG2_DFLT_CRC_STRIPPING          (1 << 12)
+#define FLAG2_CHECK_RX_HWTSTAMP           (1 << 13)
 
 #define E1000_RX_DESC_PS(R, i)	    \
 	(&(((union e1000_rx_desc_packet_split *)((R).desc))[i]))
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 636ba09ca6fb..f268cbcb751d 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -108,6 +108,7 @@ static const struct e1000_stats e1000_gstrings_stats[] = {
 	E1000_STAT("dropped_smbus", stats.mgpdc),
 	E1000_STAT("rx_dma_failed", rx_dma_failed),
 	E1000_STAT("tx_dma_failed", tx_dma_failed),
+	E1000_STAT("rx_hwtstamp_cleared", rx_hwtstamp_cleared),
 };
 
 #define E1000_GLOBAL_STATS_LEN	ARRAY_SIZE(e1000_gstrings_stats)
@@ -2182,6 +2183,28 @@ static int e1000e_set_eee(struct net_device *netdev, struct ethtool_eee *edata)
 	return 0;
 }
 
+static int e1000e_get_ts_info(struct net_device *netdev,
+			      struct ethtool_ts_info *info)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+
+	ethtool_op_get_ts_info(netdev, info);
+
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP))
+		return 0;
+
+	info->so_timestamping |= (SOF_TIMESTAMPING_TX_HARDWARE |
+				  SOF_TIMESTAMPING_RX_HARDWARE |
+				  SOF_TIMESTAMPING_RAW_HARDWARE);
+
+	info->tx_types = (1 << HWTSTAMP_TX_OFF) | (1 << HWTSTAMP_TX_ON);
+
+	info->rx_filters = ((1 << HWTSTAMP_FILTER_NONE) |
+			    (1 << HWTSTAMP_FILTER_ALL));
+
+	return 0;
+}
+
 static const struct ethtool_ops e1000_ethtool_ops = {
 	.get_settings		= e1000_get_settings,
 	.set_settings		= e1000_set_settings,
@@ -2209,7 +2232,7 @@ static const struct ethtool_ops e1000_ethtool_ops = {
 	.get_coalesce		= e1000_get_coalesce,
 	.set_coalesce		= e1000_set_coalesce,
 	.get_rxnfc		= e1000_get_rxnfc,
-	.get_ts_info		= ethtool_op_get_ts_info,
+	.get_ts_info		= e1000e_get_ts_info,
 	.get_eee		= e1000e_get_eee,
 	.set_eee		= e1000e_set_eee,
 };
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 81afad5b80f2..8e7e80345a60 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -60,6 +60,7 @@ enum e1e_registers {
 	E1000_EIAC_82574 = 0x000DC, /* Ext. Interrupt Auto Clear - RW */
 	E1000_IAM      = 0x000E0, /* Interrupt Acknowledge Auto Mask */
 	E1000_IVAR     = 0x000E4, /* Interrupt Vector Allocation - RW */
+	E1000_FEXTNVM7  = 0x000E4, /* Future Extended NVM 7 - RW */
 	E1000_EITR_82574_BASE = 0x000E8, /* Interrupt Throttling - RW */
 #define E1000_EITR_82574(_n) (E1000_EITR_82574_BASE + (_n << 2))
 	E1000_LPIC     = 0x000FC, /* Low Power Idle Control - RW */
@@ -241,6 +242,15 @@ enum e1e_registers {
 #define E1000_PCH_RAICC(_n)	(E1000_PCH_RAICC_BASE + ((_n) * 4))
 #define E1000_CRC_OFFSET	E1000_PCH_RAICC_BASE
 	E1000_HICR      = 0x08F00, /* Host Interface Control */
+	E1000_SYSTIML   = 0x0B600, /* System time register Low - RO */
+	E1000_SYSTIMH   = 0x0B604, /* System time register High - RO */
+	E1000_TIMINCA   = 0x0B608, /* Increment attributes register - RW */
+	E1000_TSYNCTXCTL = 0x0B614, /* Tx Time Sync Control register - RW */
+	E1000_TXSTMPL   = 0x0B618, /* Tx timestamp value Low - RO */
+	E1000_TXSTMPH   = 0x0B61C, /* Tx timestamp value High - RO */
+	E1000_TSYNCRXCTL = 0x0B620, /* Rx Time Sync Control register - RW */
+	E1000_RXSTMPL   = 0x0B624, /* Rx timestamp Low - RO */
+	E1000_RXSTMPH   = 0x0B628, /* Rx timestamp High - RO */
 };
 
 #define E1000_MAX_PHY_ADDR		4
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 3829f7fd1d97..50935ef48171 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -4601,6 +4601,7 @@ const struct e1000_info e1000_pch2_info = {
 	.mac			= e1000_pch2lan,
 	.flags			= FLAG_IS_ICH
 				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_HAS_CTRLEXT_ON_LOAD
 				  | FLAG_HAS_AMT
 				  | FLAG_HAS_FLASH
@@ -4620,6 +4621,7 @@ const struct e1000_info e1000_pch_lpt_info = {
 	.mac			= e1000_pch_lpt,
 	.flags			= FLAG_IS_ICH
 				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_HAS_CTRLEXT_ON_LOAD
 				  | FLAG_HAS_AMT
 				  | FLAG_HAS_FLASH
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index bf2c84cf250f..c15b7e438a44 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -487,21 +487,88 @@ static int e1000_desc_unused(struct e1000_ring *ring)
 	return ring->count + ring->next_to_clean - ring->next_to_use - 1;
 }
 
+/**
+ * e1000e_systim_to_hwtstamp - convert system time value to hw time stamp
+ * @adapter: board private structure
+ * @hwtstamps: time stamp structure to update
+ * @systim: unsigned 64bit system time value.
+ *
+ * Convert the system time value stored in the RX/TXSTMP registers into a
+ * hwtstamp which can be used by the upper level time stamping functions.
+ *
+ * The 'systim_lock' spinlock is used to protect the consistency of the
+ * system time value. This is needed because reading the 64 bit time
+ * value involves reading two 32 bit registers. The first read latches the
+ * value.
+ **/
+static void e1000e_systim_to_hwtstamp(struct e1000_adapter *adapter,
+				      struct skb_shared_hwtstamps *hwtstamps,
+				      u64 systim)
+{
+	u64 ns;
+	unsigned long flags;
+
+	spin_lock_irqsave(&adapter->systim_lock, flags);
+	ns = timecounter_cyc2time(&adapter->tc, systim);
+	spin_unlock_irqrestore(&adapter->systim_lock, flags);
+
+	memset(hwtstamps, 0, sizeof(*hwtstamps));
+	hwtstamps->hwtstamp = ns_to_ktime(ns);
+}
+
+/**
+ * e1000e_rx_hwtstamp - utility function which checks for Rx time stamp
+ * @adapter: board private structure
+ * @status: descriptor extended error and status field
+ * @skb: particular skb to include time stamp
+ *
+ * If the time stamp is valid, convert it into the timecounter ns value
+ * and store that result into the shhwtstamps structure which is passed
+ * up the network stack.
+ **/
+static void e1000e_rx_hwtstamp(struct e1000_adapter *adapter, u32 status,
+			       struct sk_buff *skb)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	u64 rxstmp;
+
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP) ||
+	    !(status & E1000_RXDEXT_STATERR_TST) ||
+	    !(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_VALID))
+		return;
+
+	/* The Rx time stamp registers contain the time stamp.  No other
+	 * received packet will be time stamped until the Rx time stamp
+	 * registers are read.  Because only one packet can be time stamped
+	 * at a time, the register values must belong to this packet and
+	 * therefore none of the other additional attributes need to be
+	 * compared.
+	 */
+	rxstmp = (u64)er32(RXSTMPL);
+	rxstmp |= (u64)er32(RXSTMPH) << 32;
+	e1000e_systim_to_hwtstamp(adapter, skb_hwtstamps(skb), rxstmp);
+
+	adapter->flags2 &= ~FLAG2_CHECK_RX_HWTSTAMP;
+}
+
 /**
  * e1000_receive_skb - helper function to handle Rx indications
  * @adapter: board private structure
- * @status: descriptor status field as written by hardware
+ * @staterr: descriptor extended error and status field as written by hardware
  * @vlan: descriptor vlan field as written by hardware (no le/be conversion)
  * @skb: pointer to sk_buff to be indicated to stack
  **/
 static void e1000_receive_skb(struct e1000_adapter *adapter,
 			      struct net_device *netdev, struct sk_buff *skb,
-			      u8 status, __le16 vlan)
+			      u32 staterr, __le16 vlan)
 {
 	u16 tag = le16_to_cpu(vlan);
+
+	e1000e_rx_hwtstamp(adapter, staterr, skb);
+
 	skb->protocol = eth_type_trans(skb, netdev);
 
-	if (status & E1000_RXD_STAT_VP)
+	if (staterr & E1000_RXD_STAT_VP)
 		__vlan_hwaccel_put_tag(skb, tag);
 
 	napi_gro_receive(&adapter->napi, skb);
@@ -1091,6 +1158,41 @@ static void e1000_print_hw_hang(struct work_struct *work)
 		e_err("Try turning off Tx pause (flow control) via ethtool\n");
 }
 
+/**
+ * e1000e_tx_hwtstamp_work - check for Tx time stamp
+ * @work: pointer to work struct
+ *
+ * This work function polls the TSYNCTXCTL valid bit to determine when a
+ * timestamp has been taken for the current stored skb.  The timestamp must
+ * be for this skb because only one such packet is allowed in the queue.
+ */
+static void e1000e_tx_hwtstamp_work(struct work_struct *work)
+{
+	struct e1000_adapter *adapter = container_of(work, struct e1000_adapter,
+						     tx_hwtstamp_work);
+	struct e1000_hw *hw = &adapter->hw;
+
+	if (!adapter->tx_hwtstamp_skb)
+		return;
+
+	if (er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_VALID) {
+		struct skb_shared_hwtstamps shhwtstamps;
+		u64 txstmp;
+
+		txstmp = er32(TXSTMPL);
+		txstmp |= (u64)er32(TXSTMPH) << 32;
+
+		e1000e_systim_to_hwtstamp(adapter, &shhwtstamps, txstmp);
+
+		skb_tstamp_tx(adapter->tx_hwtstamp_skb, &shhwtstamps);
+		dev_kfree_skb_any(adapter->tx_hwtstamp_skb);
+		adapter->tx_hwtstamp_skb = NULL;
+	} else {
+		/* reschedule to check later */
+		schedule_work(&adapter->tx_hwtstamp_work);
+	}
+}
+
 /**
  * e1000_clean_tx_irq - Reclaim resources after transmit completes
  * @tx_ring: Tx descriptor ring
@@ -1345,8 +1447,8 @@ copydone:
 			   cpu_to_le16(E1000_RXDPS_HDRSTAT_HDRSP))
 			adapter->rx_hdr_split++;
 
-		e1000_receive_skb(adapter, netdev, skb,
-				  staterr, rx_desc->wb.middle.vlan);
+		e1000_receive_skb(adapter, netdev, skb, staterr,
+				  rx_desc->wb.middle.vlan);
 
 next_desc:
 		rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF);
@@ -3303,6 +3405,159 @@ static void e1000e_setup_rss_hash(struct e1000_adapter *adapter)
 	ew32(MRQC, mrqc);
 }
 
+/**
+ * e1000e_get_base_timinca - get default SYSTIM time increment attributes
+ * @adapter: board private structure
+ * @timinca: pointer to returned time increment attributes
+ *
+ * Get attributes for incrementing the System Time Register SYSTIML/H at
+ * the default base frequency, and set the cyclecounter shift value.
+ **/
+static s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	u32 incvalue, incperiod, shift;
+
+	/* Make sure clock is enabled on I217 before checking the frequency */
+	if ((hw->mac.type == e1000_pch_lpt) &&
+	    !(er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) &&
+	    !(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_ENABLED)) {
+		u32 fextnvm7 = er32(FEXTNVM7);
+
+		if (!(fextnvm7 & (1 << 0))) {
+			ew32(FEXTNVM7, fextnvm7 | (1 << 0));
+			e1e_flush();
+		}
+	}
+
+	switch (hw->mac.type) {
+	case e1000_pch2lan:
+	case e1000_pch_lpt:
+		/* On I217, the clock frequency is 25MHz or 96MHz as
+		 * indicated by the System Clock Frequency Indication
+		 */
+		if ((hw->mac.type != e1000_pch_lpt) ||
+		    (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI)) {
+			/* Stable 96MHz frequency */
+			incperiod = INCPERIOD_96MHz;
+			incvalue = INCVALUE_96MHz;
+			shift = INCVALUE_SHIFT_96MHz;
+			adapter->cc.shift = shift + INCPERIOD_SHIFT_96MHz;
+			break;
+		}
+		/* fall-through */
+	case e1000_82574:
+	case e1000_82583:
+		/* Stable 25MHz frequency */
+		incperiod = INCPERIOD_25MHz;
+		incvalue = INCVALUE_25MHz;
+		shift = INCVALUE_SHIFT_25MHz;
+		adapter->cc.shift = shift;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	*timinca = ((incperiod << E1000_TIMINCA_INCPERIOD_SHIFT) |
+		    ((incvalue << shift) & E1000_TIMINCA_INCVALUE_MASK));
+
+	return 0;
+}
+
+/**
+ * e1000e_config_hwtstamp - configure the hwtstamp registers and enable/disable
+ * @adapter: board private structure
+ *
+ * Outgoing time stamping can be enabled and disabled. Play nice and
+ * disable it when requested, although it shouldn't cause any overhead
+ * when no packet needs it. At most one packet in the queue may be
+ * marked for time stamping, otherwise it would be impossible to tell
+ * for sure to which packet the hardware time stamp belongs.
+ *
+ * Incoming time stamping has to be configured via the hardware filters.
+ * Not all combinations are supported, in particular event type has to be
+ * specified. Matching the kind of event packet is not supported, with the
+ * exception of "all V2 events regardless of level 2 or 4".
+ **/
+static int e1000e_config_hwtstamp(struct e1000_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	struct hwtstamp_config *config = &adapter->hwtstamp_config;
+	u32 tsync_tx_ctl = E1000_TSYNCTXCTL_ENABLED;
+	u32 tsync_rx_ctl = E1000_TSYNCRXCTL_ENABLED;
+	u32 regval;
+	s32 ret_val;
+
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP))
+		return -EINVAL;
+
+	/* flags reserved for future extensions - must be zero */
+	if (config->flags)
+		return -EINVAL;
+
+	switch (config->tx_type) {
+	case HWTSTAMP_TX_OFF:
+		tsync_tx_ctl = 0;
+		break;
+	case HWTSTAMP_TX_ON:
+		break;
+	default:
+		return -ERANGE;
+	}
+
+	switch (config->rx_filter) {
+	case HWTSTAMP_FILTER_NONE:
+		tsync_rx_ctl = 0;
+		break;
+	case HWTSTAMP_FILTER_ALL:
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_ALL;
+		config->rx_filter = HWTSTAMP_FILTER_ALL;
+		break;
+	default:
+		return -ERANGE;
+	}
+
+	/* enable/disable Tx h/w time stamping */
+	regval = er32(TSYNCTXCTL);
+	regval &= ~E1000_TSYNCTXCTL_ENABLED;
+	regval |= tsync_tx_ctl;
+	ew32(TSYNCTXCTL, regval);
+	if ((er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) !=
+	    (regval & E1000_TSYNCTXCTL_ENABLED)) {
+		e_err("Timesync Tx Control register not set as expected\n");
+		return -EAGAIN;
+	}
+
+	/* enable/disable Rx h/w time stamping */
+	regval = er32(TSYNCRXCTL);
+	regval &= ~(E1000_TSYNCRXCTL_ENABLED | E1000_TSYNCRXCTL_TYPE_MASK);
+	regval |= tsync_rx_ctl;
+	ew32(TSYNCRXCTL, regval);
+	if ((er32(TSYNCRXCTL) & (E1000_TSYNCRXCTL_ENABLED |
+				 E1000_TSYNCRXCTL_TYPE_MASK)) !=
+	    (regval & (E1000_TSYNCRXCTL_ENABLED |
+		       E1000_TSYNCRXCTL_TYPE_MASK))) {
+		e_err("Timesync Rx Control register not set as expected\n");
+		return -EAGAIN;
+	}
+
+	/* Clear TSYNCRXCTL_VALID & TSYNCTXCTL_VALID bit */
+	regval = er32(RXSTMPH);
+	regval = er32(TXSTMPH);
+
+	/* Get and set the System Time Register SYSTIM base frequency */
+	ret_val = e1000e_get_base_timinca(adapter, &regval);
+	if (ret_val)
+		return ret_val;
+	ew32(TIMINCA, regval);
+
+	/* reset the ns time counter */
+	timecounter_init(&adapter->tc, &adapter->cc,
+			 ktime_to_ns(ktime_get_real()));
+
+	return 0;
+}
+
 /**
  * e1000_configure - configure the hardware for Rx and Tx
  * @adapter: private board structure
@@ -3529,6 +3784,9 @@ void e1000e_reset(struct e1000_adapter *adapter)
 
 	e1000e_reset_adaptive(hw);
 
+	/* initialize systim and reset the ns time counter */
+	e1000e_config_hwtstamp(adapter);
+
 	if (!netif_running(adapter->netdev) &&
 	    !test_bit(__E1000_TESTING, &adapter->state)) {
 		e1000_power_down_phy(adapter);
@@ -3664,6 +3922,24 @@ void e1000e_reinit_locked(struct e1000_adapter *adapter)
 	clear_bit(__E1000_RESETTING, &adapter->state);
 }
 
+/**
+ * e1000e_cyclecounter_read - read raw cycle counter (used by time counter)
+ * @cc: cyclecounter structure
+ **/
+static cycle_t e1000e_cyclecounter_read(const struct cyclecounter *cc)
+{
+	struct e1000_adapter *adapter = container_of(cc, struct e1000_adapter,
+						     cc);
+	struct e1000_hw *hw = &adapter->hw;
+	cycle_t systim;
+
+	/* latch SYSTIMH on read of SYSTIML */
+	systim = (cycle_t)er32(SYSTIML);
+	systim |= (cycle_t)er32(SYSTIMH) << 32;
+
+	return systim;
+}
+
 /**
  * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
  * @adapter: board private structure to initialize
@@ -3690,6 +3966,17 @@ static int e1000_sw_init(struct e1000_adapter *adapter)
 	if (e1000_alloc_queues(adapter))
 		return -ENOMEM;
 
+	/* Setup hardware time stamping cyclecounter */
+	if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) {
+		adapter->cc.read = e1000e_cyclecounter_read;
+		adapter->cc.mask = CLOCKSOURCE_MASK(64);
+		adapter->cc.mult = 1;
+		/* cc.shift set in e1000e_get_base_tininca() */
+
+		spin_lock_init(&adapter->systim_lock);
+		INIT_WORK(&adapter->tx_hwtstamp_work, e1000e_tx_hwtstamp_work);
+	}
+
 	/* Explicitly disable IRQ since the NIC can be in any state. */
 	e1000_irq_disable(adapter);
 
@@ -4597,6 +4884,17 @@ link_up:
 	if (adapter->flags2 & FLAG2_CHECK_PHY_HANG)
 		e1000e_check_82574_phy_workaround(adapter);
 
+	/* Clear valid timestamp stuck in RXSTMPL/H due to a Rx error */
+	if (adapter->hwtstamp_config.rx_filter != HWTSTAMP_FILTER_NONE) {
+		if ((adapter->flags2 & FLAG2_CHECK_RX_HWTSTAMP) &&
+		    (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_VALID)) {
+			er32(RXSTMPH);
+			adapter->rx_hwtstamp_cleared++;
+		} else {
+			adapter->flags2 |= FLAG2_CHECK_RX_HWTSTAMP;
+		}
+	}
+
 	/* Reset the timer */
 	if (!test_bit(__E1000_DOWN, &adapter->state))
 		mod_timer(&adapter->watchdog_timer,
@@ -4608,6 +4906,7 @@ link_up:
 #define E1000_TX_FLAGS_TSO		0x00000004
 #define E1000_TX_FLAGS_IPV4		0x00000008
 #define E1000_TX_FLAGS_NO_FCS		0x00000010
+#define E1000_TX_FLAGS_HWTSTAMP		0x00000020
 #define E1000_TX_FLAGS_VLAN_MASK	0xffff0000
 #define E1000_TX_FLAGS_VLAN_SHIFT	16
 
@@ -4866,6 +5165,11 @@ static void e1000_tx_queue(struct e1000_ring *tx_ring, int tx_flags, int count)
 	if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS))
 		txd_lower &= ~(E1000_TXD_CMD_IFCS);
 
+	if (unlikely(tx_flags & E1000_TX_FLAGS_HWTSTAMP)) {
+		txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
+		txd_upper |= E1000_TXD_EXTCMD_TSTAMP;
+	}
+
 	i = tx_ring->next_to_use;
 
 	do {
@@ -5089,7 +5393,15 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
 	count = e1000_tx_map(tx_ring, skb, first, adapter->tx_fifo_limit,
 			     nr_frags);
 	if (count) {
-		skb_tx_timestamp(skb);
+		if (unlikely((skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP) &&
+			     !adapter->tx_hwtstamp_skb)) {
+			skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
+			tx_flags |= E1000_TX_FLAGS_HWTSTAMP;
+			adapter->tx_hwtstamp_skb = skb_get(skb);
+			schedule_work(&adapter->tx_hwtstamp_work);
+		} else {
+			skb_tx_timestamp(skb);
+		}
 
 		netdev_sent_queue(netdev, skb->len);
 		e1000_tx_queue(tx_ring, tx_flags, count);
@@ -5317,6 +5629,43 @@ static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
 	return 0;
 }
 
+/**
+ * e1000e_hwtstamp_ioctl - control hardware time stamping
+ * @netdev: network interface device structure
+ * @ifreq: interface request
+ *
+ * Outgoing time stamping can be enabled and disabled. Play nice and
+ * disable it when requested, although it shouldn't cause any overhead
+ * when no packet needs it. At most one packet in the queue may be
+ * marked for time stamping, otherwise it would be impossible to tell
+ * for sure to which packet the hardware time stamp belongs.
+ *
+ * Incoming time stamping has to be configured via the hardware filters.
+ * Not all combinations are supported, in particular event type has to be
+ * specified. Matching the kind of event packet is not supported, with the
+ * exception of "all V2 events regardless of level 2 or 4".
+ **/
+static int e1000e_hwtstamp_ioctl(struct net_device *netdev, struct ifreq *ifr)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+	struct hwtstamp_config config;
+	int ret_val;
+
+	if (copy_from_user(&config, ifr->ifr_data, sizeof(config)))
+		return -EFAULT;
+
+	adapter->hwtstamp_config = config;
+
+	ret_val = e1000e_config_hwtstamp(adapter);
+	if (ret_val)
+		return ret_val;
+
+	config = adapter->hwtstamp_config;
+
+	return copy_to_user(ifr->ifr_data, &config,
+			    sizeof(config)) ? -EFAULT : 0;
+}
+
 static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
 {
 	switch (cmd) {
@@ -5324,6 +5673,8 @@ static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
 	case SIOCGMIIREG:
 	case SIOCSMIIREG:
 		return e1000_mii_ioctl(netdev, ifr, cmd);
+	case SIOCSHWTSTAMP:
+		return e1000e_hwtstamp_ioctl(netdev, ifr);
 	default:
 		return -EOPNOTSUPP;
 	}
@@ -6380,6 +6731,14 @@ static void e1000_remove(struct pci_dev *pdev)
 	cancel_work_sync(&adapter->update_phy_task);
 	cancel_work_sync(&adapter->print_hang_task);
 
+	if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) {
+		cancel_work_sync(&adapter->tx_hwtstamp_work);
+		if (adapter->tx_hwtstamp_skb) {
+			dev_kfree_skb_any(adapter->tx_hwtstamp_skb);
+			adapter->tx_hwtstamp_skb = NULL;
+		}
+	}
+
 	if (!(netdev->flags & IFF_UP))
 		e1000_power_down_phy(adapter);
 
-- 
cgit v1.2.3


From a8fc18910b7f35a59345b5f5cd140c7f64d57d86 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:25:36 +0000
Subject: e1000e: fix ethtool offline register test for I217

The SHRAH[9] register on I217 has a different R/W bit-mask than RAR and
SHRAL/H registers.  Set R/W bit-mask appropriately for SHRAH[9] when
testing the R/W ability of the register.  Also, fix the error message log
format so that it does not provide misleading information (i.e. the logged
register address could be incorrect).

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ethtool.c | 25 +++++++++++++++++--------
 1 file changed, 17 insertions(+), 8 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index f268cbcb751d..ceff1bf300b3 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -760,8 +760,9 @@ static bool reg_pattern_test(struct e1000_adapter *adapter, u64 *data,
 				      (test[pat] & write));
 		val = E1000_READ_REG_ARRAY(&adapter->hw, reg, offset);
 		if (val != (test[pat] & write & mask)) {
-			e_err("pattern test reg %04X failed: got 0x%08X expected 0x%08X\n",
-			      reg + offset, val, (test[pat] & write & mask));
+			e_err("pattern test failed (reg 0x%05X): got 0x%08X expected 0x%08X\n",
+			      reg + (offset << 2), val,
+			      (test[pat] & write & mask));
 			*data = reg;
 			return 1;
 		}
@@ -776,7 +777,7 @@ static bool reg_set_and_check(struct e1000_adapter *adapter, u64 *data,
 	__ew32(&adapter->hw, reg, write & mask);
 	val = __er32(&adapter->hw, reg);
 	if ((write & mask) != (val & mask)) {
-		e_err("set/check reg %04X test failed: got 0x%08X expected 0x%08X\n",
+		e_err("set/check test failed (reg 0x%05X): got 0x%08X expected 0x%08X\n",
 		      reg, (val & mask), (write & mask));
 		*data = reg;
 		return 1;
@@ -884,12 +885,20 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
 		    E1000_FWSM_WLOCK_MAC_SHIFT;
 
 	for (i = 0; i < mac->rar_entry_count; i++) {
-		/* Cannot test write-protected SHRAL[n] registers */
-		if ((wlock_mac == 1) || (wlock_mac && (i > wlock_mac)))
-			continue;
+		if (mac->type == e1000_pch_lpt) {
+			/* Cannot test write-protected SHRAL[n] registers */
+			if ((wlock_mac == 1) || (wlock_mac && (i > wlock_mac)))
+				continue;
+
+			/* SHRAH[9] different than the others */
+			if (i == 10)
+				mask |= (1 << 30);
+			else
+				mask &= ~(1 << 30);
+		}
 
-		REG_PATTERN_TEST_ARRAY(E1000_RA, ((i << 1) + 1),
-				       mask, 0xFFFFFFFF);
+		REG_PATTERN_TEST_ARRAY(E1000_RA, ((i << 1) + 1), mask,
+				       0xFFFFFFFF);
 	}
 
 	for (i = 0; i < mac->mta_reg_count; i++)
-- 
cgit v1.2.3


From 347b5201cb2e8b9e4a20d81582563f51336eb215 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 8 Dec 2012 00:35:35 +0000
Subject: e1000e: fix flow-control thresholds for jumbo frames on
 82579/I217/I218

The previous static flow-control thresholds were causing unnecessary pause
packets to be transmitted when jumbo frames are configured reducing the
throughput.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index c15b7e438a44..8bb5d28eca14 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -3724,14 +3724,17 @@ void e1000e_reset(struct e1000_adapter *adapter)
 		break;
 	case e1000_pch2lan:
 	case e1000_pch_lpt:
-		fc->high_water = 0x05C20;
-		fc->low_water = 0x05048;
-		fc->pause_time = 0x0650;
 		fc->refresh_time = 0x0400;
-		if (adapter->netdev->mtu > ETH_DATA_LEN) {
-			pba = 14;
-			ew32(PBA, pba);
+
+		if (adapter->netdev->mtu <= ETH_DATA_LEN) {
+			fc->high_water = 0x05C20;
+			fc->low_water = 0x05048;
+			fc->pause_time = 0x0650;
+			break;
 		}
+
+		fc->high_water = ((pba << 10) * 9 / 10) & E1000_FCRTH_RTH;
+		fc->low_water = ((pba << 10) * 8 / 10) & E1000_FCRTL_RTL;
 		break;
 	}
 
-- 
cgit v1.2.3


From d89777bf0e42e7cb6ce8eae35190b9375c3b4211 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 19 Jan 2013 01:09:58 +0000
Subject: e1000e: add support for IEEE-1588 PTP

Add PTP IEEE-1588 support and make accesible via the PHC subsystem.

v2: make e1000e_ptp_clock_info a static const struct per Stephen Hemminger

Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reviewed-by: Jacob Keller <Jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/Kconfig          |   1 +
 drivers/net/ethernet/intel/e1000e/Makefile  |   2 +-
 drivers/net/ethernet/intel/e1000e/defines.h |  11 ++
 drivers/net/ethernet/intel/e1000e/e1000.h   |   9 +-
 drivers/net/ethernet/intel/e1000e/ethtool.c |  12 ++
 drivers/net/ethernet/intel/e1000e/hw.h      |   2 +
 drivers/net/ethernet/intel/e1000e/netdev.c  | 107 ++++++++++-
 drivers/net/ethernet/intel/e1000e/ptp.c     | 276 ++++++++++++++++++++++++++++
 8 files changed, 417 insertions(+), 3 deletions(-)
 create mode 100644 drivers/net/ethernet/intel/e1000e/ptp.c

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/Kconfig b/drivers/net/ethernet/intel/Kconfig
index 21353f0fef63..3d5f6d463757 100644
--- a/drivers/net/ethernet/intel/Kconfig
+++ b/drivers/net/ethernet/intel/Kconfig
@@ -74,6 +74,7 @@ config E1000E
 	tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
 	depends on PCI && (!SPARC32 || BROKEN)
 	select CRC32
+	select PTP_1588_CLOCK
 	---help---
 	  This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
 	  ethernet family of adapters. For PCI or PCI-X e1000 adapters,
diff --git a/drivers/net/ethernet/intel/e1000e/Makefile b/drivers/net/ethernet/intel/e1000e/Makefile
index 591b71324505..1da0faac0411 100644
--- a/drivers/net/ethernet/intel/e1000e/Makefile
+++ b/drivers/net/ethernet/intel/e1000e/Makefile
@@ -34,5 +34,5 @@ obj-$(CONFIG_E1000E) += e1000e.o
 
 e1000e-objs := 82571.o ich8lan.o 80003es2lan.o \
 	       mac.o manage.o nvm.o phy.o \
-	       param.o ethtool.o netdev.o
+	       param.o ethtool.o netdev.o ptp.o
 
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 36f9fad19a76..5cb7441dca2a 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -544,9 +544,20 @@
 
 #define E1000_TSYNCRXCTL_VALID		0x00000001 /* Rx timestamp valid */
 #define E1000_TSYNCRXCTL_TYPE_MASK	0x0000000E /* Rx type mask */
+#define E1000_TSYNCRXCTL_TYPE_L2_V2	0x00
+#define E1000_TSYNCRXCTL_TYPE_L4_V1	0x02
+#define E1000_TSYNCRXCTL_TYPE_L2_L4_V2	0x04
+#define E1000_TSYNCRXCTL_TYPE_ALL	0x08
+#define E1000_TSYNCRXCTL_TYPE_EVENT_V2	0x0A
 #define E1000_TSYNCRXCTL_ENABLED	0x00000010 /* enable Rx timestamping */
 #define E1000_TSYNCRXCTL_SYSCFI		0x00000020 /* Sys clock frequency */
 
+#define E1000_RXMTRL_PTP_V1_SYNC_MESSAGE	0x00000000
+#define E1000_RXMTRL_PTP_V1_DELAY_REQ_MESSAGE	0x00010000
+
+#define E1000_RXMTRL_PTP_V2_SYNC_MESSAGE	0x00000000
+#define E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE	0x01000000
+
 #define E1000_TIMINCA_INCPERIOD_SHIFT	24
 #define E1000_TIMINCA_INCVALUE_MASK	0x00FFFFFF
 
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index dea9e5552966..bd5876171376 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -43,7 +43,8 @@
 #include <linux/if_vlan.h>
 #include <linux/clocksource.h>
 #include <linux/net_tstamp.h>
-
+#include <linux/ptp_clock_kernel.h>
+#include <linux/ptp_classify.h>
 #include "hw.h"
 
 struct e1000_info;
@@ -413,6 +414,8 @@ struct e1000_adapter {
 	spinlock_t systim_lock;	/* protects SYSTIML/H regsters */
 	struct cyclecounter cc;
 	struct timecounter tc;
+	struct ptp_clock *ptp_clock;
+	struct ptp_clock_info ptp_clock_info;
 };
 
 struct e1000_info {
@@ -427,6 +430,8 @@ struct e1000_info {
 	const struct e1000_nvm_operations *nvm_ops;
 };
 
+s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca);
+
 /* The system time is maintained by a 64-bit counter comprised of the 32-bit
  * SYSTIMH and SYSTIML registers.  How the counter increments (and therefore
  * its resolution) is based on the contents of the TIMINCA register - it
@@ -704,6 +709,8 @@ extern s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_igp(struct e1000_hw *hw);
 extern bool e1000_check_phy_82574(struct e1000_hw *hw);
 extern s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
+extern void e1000e_ptp_init(struct e1000_adapter *adapter);
+extern void e1000e_ptp_remove(struct e1000_adapter *adapter);
 
 static inline s32 e1000_phy_hw_reset(struct e1000_hw *hw)
 {
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index ceff1bf300b3..e3855bb10599 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -2209,8 +2209,20 @@ static int e1000e_get_ts_info(struct net_device *netdev,
 	info->tx_types = (1 << HWTSTAMP_TX_OFF) | (1 << HWTSTAMP_TX_ON);
 
 	info->rx_filters = ((1 << HWTSTAMP_FILTER_NONE) |
+			    (1 << HWTSTAMP_FILTER_PTP_V1_L4_SYNC) |
+			    (1 << HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_L4_SYNC) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_L2_SYNC) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_EVENT) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_SYNC) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_DELAY_REQ) |
 			    (1 << HWTSTAMP_FILTER_ALL));
 
+	if (adapter->ptp_clock)
+		info->phc_index = ptp_clock_index(adapter->ptp_clock);
+
 	return 0;
 }
 
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 8e7e80345a60..84e6beb78718 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -251,6 +251,8 @@ enum e1e_registers {
 	E1000_TSYNCRXCTL = 0x0B620, /* Rx Time Sync Control register - RW */
 	E1000_RXSTMPL   = 0x0B624, /* Rx timestamp Low - RO */
 	E1000_RXSTMPH   = 0x0B628, /* Rx timestamp High - RO */
+	E1000_RXMTRL    = 0x0B634, /* Timesync Rx EtherType and Msg Type - RW */
+	E1000_RXUDP     = 0x0B638, /* Timesync Rx UDP Port - RW */
 };
 
 #define E1000_MAX_PHY_ADDR		4
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 8bb5d28eca14..34be756ee1e2 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -3413,7 +3413,7 @@ static void e1000e_setup_rss_hash(struct e1000_adapter *adapter)
  * Get attributes for incrementing the System Time Register SYSTIML/H at
  * the default base frequency, and set the cyclecounter shift value.
  **/
-static s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca)
+s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca)
 {
 	struct e1000_hw *hw = &adapter->hw;
 	u32 incvalue, incperiod, shift;
@@ -3485,6 +3485,10 @@ static int e1000e_config_hwtstamp(struct e1000_adapter *adapter)
 	struct hwtstamp_config *config = &adapter->hwtstamp_config;
 	u32 tsync_tx_ctl = E1000_TSYNCTXCTL_ENABLED;
 	u32 tsync_rx_ctl = E1000_TSYNCRXCTL_ENABLED;
+	u32 rxmtrl = 0;
+	u16 rxudp = 0;
+	bool is_l4 = false;
+	bool is_l2 = false;
 	u32 regval;
 	s32 ret_val;
 
@@ -3509,7 +3513,69 @@ static int e1000e_config_hwtstamp(struct e1000_adapter *adapter)
 	case HWTSTAMP_FILTER_NONE:
 		tsync_rx_ctl = 0;
 		break;
+	case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L4_V1;
+		rxmtrl = E1000_RXMTRL_PTP_V1_SYNC_MESSAGE;
+		is_l4 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L4_V1;
+		rxmtrl = E1000_RXMTRL_PTP_V1_DELAY_REQ_MESSAGE;
+		is_l4 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
+		/* Also time stamps V2 L2 Path Delay Request/Response */
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_V2;
+		rxmtrl = E1000_RXMTRL_PTP_V2_SYNC_MESSAGE;
+		is_l2 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
+		/* Also time stamps V2 L2 Path Delay Request/Response. */
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_V2;
+		rxmtrl = E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE;
+		is_l2 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
+		/* Hardware cannot filter just V2 L4 Sync messages;
+		 * fall-through to V2 (both L2 and L4) Sync.
+		 */
+	case HWTSTAMP_FILTER_PTP_V2_SYNC:
+		/* Also time stamps V2 Path Delay Request/Response. */
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_L4_V2;
+		rxmtrl = E1000_RXMTRL_PTP_V2_SYNC_MESSAGE;
+		is_l2 = true;
+		is_l4 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
+		/* Hardware cannot filter just V2 L4 Delay Request messages;
+		 * fall-through to V2 (both L2 and L4) Delay Request.
+		 */
+	case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
+		/* Also time stamps V2 Path Delay Request/Response. */
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_L4_V2;
+		rxmtrl = E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE;
+		is_l2 = true;
+		is_l4 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
+	case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
+		/* Hardware cannot filter just V2 L4 or L2 Event messages;
+		 * fall-through to all V2 (both L2 and L4) Events.
+		 */
+	case HWTSTAMP_FILTER_PTP_V2_EVENT:
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_EVENT_V2;
+		config->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
+		is_l2 = true;
+		is_l4 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
+		/* For V1, the hardware can only filter Sync messages or
+		 * Delay Request messages but not both so fall-through to
+		 * time stamp all packets.
+		 */
 	case HWTSTAMP_FILTER_ALL:
+		is_l2 = true;
+		is_l4 = true;
 		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_ALL;
 		config->rx_filter = HWTSTAMP_FILTER_ALL;
 		break;
@@ -3541,6 +3607,22 @@ static int e1000e_config_hwtstamp(struct e1000_adapter *adapter)
 		return -EAGAIN;
 	}
 
+	/* L2: define ethertype filter for time stamped packets */
+	if (is_l2)
+		rxmtrl |= ETH_P_1588;
+
+	/* define which PTP packets get time stamped */
+	ew32(RXMTRL, rxmtrl);
+
+	/* Filter by destination port */
+	if (is_l4) {
+		rxudp = PTP_EV_PORT;
+		cpu_to_be16s(&rxudp);
+	}
+	ew32(RXUDP, rxudp);
+
+	e1e_flush();
+
 	/* Clear TSYNCRXCTL_VALID & TSYNCTXCTL_VALID bit */
 	regval = er32(RXSTMPH);
 	regval = er32(TXSTMPH);
@@ -5665,6 +5747,24 @@ static int e1000e_hwtstamp_ioctl(struct net_device *netdev, struct ifreq *ifr)
 
 	config = adapter->hwtstamp_config;
 
+	switch (config.rx_filter) {
+	case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
+	case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
+	case HWTSTAMP_FILTER_PTP_V2_SYNC:
+	case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
+	case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
+	case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
+		/* With V2 type filters which specify a Sync or Delay Request,
+		 * Path Delay Request/Response messages are also time stamped
+		 * by hardware so notify the caller the requested packets plus
+		 * some others are time stamped.
+		 */
+		config.rx_filter = HWTSTAMP_FILTER_SOME;
+		break;
+	default:
+		break;
+	}
+
 	return copy_to_user(ifr->ifr_data, &config,
 			    sizeof(config)) ? -EFAULT : 0;
 }
@@ -6672,6 +6772,9 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	/* carrier off reporting is important to ethtool even BEFORE open */
 	netif_carrier_off(netdev);
 
+	/* init PTP hardware clock */
+	e1000e_ptp_init(adapter);
+
 	e1000_print_device_info(adapter);
 
 	if (pci_dev_run_wake(pdev))
@@ -6720,6 +6823,8 @@ static void e1000_remove(struct pci_dev *pdev)
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	bool down = test_bit(__E1000_DOWN, &adapter->state);
 
+	e1000e_ptp_remove(adapter);
+
 	/* The timers may be rescheduled, so explicitly disable them
 	 * from being rescheduled.
 	 */
diff --git a/drivers/net/ethernet/intel/e1000e/ptp.c b/drivers/net/ethernet/intel/e1000e/ptp.c
new file mode 100644
index 000000000000..32da00c0cbc9
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/ptp.c
@@ -0,0 +1,276 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2012 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/* PTP 1588 Hardware Clock (PHC)
+ * Derived from PTP Hardware Clock driver for Intel 82576 and 82580 (igb)
+ * Copyright (C) 2011 Richard Cochran <richardcochran@gmail.com>
+ */
+
+#include "e1000.h"
+
+/**
+ * e1000e_phc_adjfreq - adjust the frequency of the hardware clock
+ * @ptp: ptp clock structure
+ * @delta: Desired frequency change in parts per billion
+ *
+ * Adjust the frequency of the PHC cycle counter by the indicated delta from
+ * the base frequency.
+ **/
+static int e1000e_phc_adjfreq(struct ptp_clock_info *ptp, s32 delta)
+{
+	struct e1000_adapter *adapter = container_of(ptp, struct e1000_adapter,
+						     ptp_clock_info);
+	struct e1000_hw *hw = &adapter->hw;
+	bool neg_adj = false;
+	u64 adjustment;
+	u32 timinca, incvalue;
+	s32 ret_val;
+
+	if ((delta > ptp->max_adj) || (delta <= -1000000000))
+		return -EINVAL;
+
+	if (delta < 0) {
+		neg_adj = true;
+		delta = -delta;
+	}
+
+	/* Get the System Time Register SYSTIM base frequency */
+	ret_val = e1000e_get_base_timinca(adapter, &timinca);
+	if (ret_val)
+		return ret_val;
+
+	incvalue = timinca & E1000_TIMINCA_INCVALUE_MASK;
+
+	adjustment = incvalue;
+	adjustment *= delta;
+	adjustment = div_u64(adjustment, 1000000000);
+
+	incvalue = neg_adj ? (incvalue - adjustment) : (incvalue + adjustment);
+
+	timinca &= ~E1000_TIMINCA_INCVALUE_MASK;
+	timinca |= incvalue;
+
+	ew32(TIMINCA, timinca);
+
+	return 0;
+}
+
+/**
+ * e1000e_phc_adjtime - Shift the time of the hardware clock
+ * @ptp: ptp clock structure
+ * @delta: Desired change in nanoseconds
+ *
+ * Adjust the timer by resetting the timecounter structure.
+ **/
+static int e1000e_phc_adjtime(struct ptp_clock_info *ptp, s64 delta)
+{
+	struct e1000_adapter *adapter = container_of(ptp, struct e1000_adapter,
+						     ptp_clock_info);
+	unsigned long flags;
+	s64 now;
+
+	spin_lock_irqsave(&adapter->systim_lock, flags);
+	now = timecounter_read(&adapter->tc);
+	now += delta;
+	timecounter_init(&adapter->tc, &adapter->cc, now);
+	spin_unlock_irqrestore(&adapter->systim_lock, flags);
+
+	return 0;
+}
+
+/**
+ * e1000e_phc_gettime - Reads the current time from the hardware clock
+ * @ptp: ptp clock structure
+ * @ts: timespec structure to hold the current time value
+ *
+ * Read the timecounter and return the correct value in ns after converting
+ * it into a struct timespec.
+ **/
+static int e1000e_phc_gettime(struct ptp_clock_info *ptp, struct timespec *ts)
+{
+	struct e1000_adapter *adapter = container_of(ptp, struct e1000_adapter,
+						     ptp_clock_info);
+	unsigned long flags;
+	u32 remainder;
+	u64 ns;
+
+	spin_lock_irqsave(&adapter->systim_lock, flags);
+	ns = timecounter_read(&adapter->tc);
+	spin_unlock_irqrestore(&adapter->systim_lock, flags);
+
+	ts->tv_sec = div_u64_rem(ns, NSEC_PER_SEC, &remainder);
+	ts->tv_nsec = remainder;
+
+	return 0;
+}
+
+/**
+ * e1000e_phc_settime - Set the current time on the hardware clock
+ * @ptp: ptp clock structure
+ * @ts: timespec containing the new time for the cycle counter
+ *
+ * Reset the timecounter to use a new base value instead of the kernel
+ * wall timer value.
+ **/
+static int e1000e_phc_settime(struct ptp_clock_info *ptp,
+			      const struct timespec *ts)
+{
+	struct e1000_adapter *adapter = container_of(ptp, struct e1000_adapter,
+						     ptp_clock_info);
+	unsigned long flags;
+	u64 ns;
+
+	ns = ts->tv_sec * NSEC_PER_SEC;
+	ns += ts->tv_nsec;
+
+	/* reset the timecounter */
+	spin_lock_irqsave(&adapter->systim_lock, flags);
+	timecounter_init(&adapter->tc, &adapter->cc, ns);
+	spin_unlock_irqrestore(&adapter->systim_lock, flags);
+
+	return 0;
+}
+
+/**
+ * e1000e_phc_enable - enable or disable an ancillary feature
+ * @ptp: ptp clock structure
+ * @request: Desired resource to enable or disable
+ * @on: Caller passes one to enable or zero to disable
+ *
+ * Enable (or disable) ancillary features of the PHC subsystem.
+ * Currently, no ancillary features are supported.
+ **/
+static int e1000e_phc_enable(struct ptp_clock_info *ptp,
+			     struct ptp_clock_request *request, int on)
+{
+	return -EOPNOTSUPP;
+}
+
+static void e1000e_systim_overflow_work(struct work_struct *work)
+{
+	struct e1000_adapter *adapter = container_of(work, struct e1000_adapter,
+						     systim_overflow_work.work);
+	struct e1000_hw *hw = &adapter->hw;
+	struct timespec ts;
+
+	adapter->ptp_clock_info.gettime(&adapter->ptp_clock_info, &ts);
+
+	e_dbg("SYSTIM overflow check at %ld.%09lu\n", ts.tv_sec, ts.tv_nsec);
+
+	schedule_delayed_work(&adapter->systim_overflow_work,
+			      E1000_SYSTIM_OVERFLOW_PERIOD);
+}
+
+static const struct ptp_clock_info e1000e_ptp_clock_info = {
+	.owner		= THIS_MODULE,
+	.n_alarm	= 0,
+	.n_ext_ts	= 0,
+	.n_per_out	= 0,
+	.pps		= 0,
+	.adjfreq	= e1000e_phc_adjfreq,
+	.adjtime	= e1000e_phc_adjtime,
+	.gettime	= e1000e_phc_gettime,
+	.settime	= e1000e_phc_settime,
+	.enable		= e1000e_phc_enable,
+};
+
+/**
+ * e1000e_ptp_init - initialize PTP for devices which support it
+ * @adapter: board private structure
+ *
+ * This function performs the required steps for enabling PTP support.
+ * If PTP support has already been loaded it simply calls the cyclecounter
+ * init routine and exits.
+ **/
+void e1000e_ptp_init(struct e1000_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+
+	adapter->ptp_clock = NULL;
+
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP))
+		return;
+
+	adapter->ptp_clock_info = e1000e_ptp_clock_info;
+
+	snprintf(adapter->ptp_clock_info.name,
+		 sizeof(adapter->ptp_clock_info.name), "%pm",
+		 adapter->netdev->perm_addr);
+
+	switch (hw->mac.type) {
+	case e1000_pch2lan:
+	case e1000_pch_lpt:
+		if ((hw->mac.type != e1000_pch_lpt) ||
+		    (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI)) {
+			adapter->ptp_clock_info.max_adj = 24000000 - 1;
+			break;
+		}
+		/* fall-through */
+	case e1000_82574:
+	case e1000_82583:
+		adapter->ptp_clock_info.max_adj = 600000000 - 1;
+		break;
+	default:
+		break;
+	}
+
+	INIT_DELAYED_WORK(&adapter->systim_overflow_work,
+			  e1000e_systim_overflow_work);
+
+	schedule_delayed_work(&adapter->systim_overflow_work,
+			      E1000_SYSTIM_OVERFLOW_PERIOD);
+
+	adapter->ptp_clock = ptp_clock_register(&adapter->ptp_clock_info,
+						&adapter->pdev->dev);
+	if (IS_ERR(adapter->ptp_clock)) {
+		adapter->ptp_clock = NULL;
+		e_err("ptp_clock_register failed\n");
+	} else {
+		e_info("registered PHC clock\n");
+	}
+}
+
+/**
+ * e1000e_ptp_remove - disable PTP device and stop the overflow check
+ * @adapter: board private structure
+ *
+ * Stop the PTP support, and cancel the delayed work.
+ **/
+void e1000e_ptp_remove(struct e1000_adapter *adapter)
+{
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP))
+		return;
+
+	cancel_delayed_work_sync(&adapter->systim_overflow_work);
+
+	if (adapter->ptp_clock) {
+		ptp_clock_unregister(adapter->ptp_clock);
+		adapter->ptp_clock = NULL;
+		e_info("removed PHC\n");
+	}
+}
-- 
cgit v1.2.3


From 94fb848bf43fae3410639fb2110a783200e9e1da Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 23 Jan 2013 09:00:03 +0000
Subject: e1000e: enable ECC on I217/I218 to catch packet buffer memory errors

In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions.  Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors.  Correctable errors will be handled
by the hardware.  Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded.  If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error.  The driver will then reset the hardware in order to
clear the error and restart.

Both types of errors will be accounted for in statistics counters.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  9 ++++++
 drivers/net/ethernet/intel/e1000e/e1000.h   |  2 ++
 drivers/net/ethernet/intel/e1000e/ethtool.c |  2 ++
 drivers/net/ethernet/intel/e1000e/hw.h      |  1 +
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 11 +++++++
 drivers/net/ethernet/intel/e1000e/netdev.c  | 46 +++++++++++++++++++++++++++++
 6 files changed, 71 insertions(+)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 5cb7441dca2a..f0452311c95a 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -233,6 +233,7 @@
 #define E1000_CTRL_FRCDPX   0x00001000  /* Force Duplex */
 #define E1000_CTRL_LANPHYPC_OVERRIDE 0x00010000 /* SW control of LANPHYPC */
 #define E1000_CTRL_LANPHYPC_VALUE    0x00020000 /* SW value of LANPHYPC */
+#define E1000_CTRL_MEHE     0x00080000  /* Memory Error Handling Enable */
 #define E1000_CTRL_SWDPIN0  0x00040000  /* SWDPIN 0 value */
 #define E1000_CTRL_SWDPIN1  0x00080000  /* SWDPIN 1 value */
 #define E1000_CTRL_SWDPIO0  0x00400000  /* SWDPIN 0 Input or output */
@@ -394,6 +395,12 @@
 
 #define E1000_PBS_16K E1000_PBA_16K
 
+/* Uncorrectable/correctable ECC Error counts and enable bits */
+#define E1000_PBECCSTS_CORR_ERR_CNT_MASK	0x000000FF
+#define E1000_PBECCSTS_UNCORR_ERR_CNT_MASK	0x0000FF00
+#define E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT	8
+#define E1000_PBECCSTS_ECC_ENABLE		0x00010000
+
 #define IFS_MAX       80
 #define IFS_MIN       40
 #define IFS_RATIO     4
@@ -413,6 +420,7 @@
 #define E1000_ICR_RXSEQ         0x00000008 /* Rx sequence error */
 #define E1000_ICR_RXDMT0        0x00000010 /* Rx desc min. threshold (0) */
 #define E1000_ICR_RXT0          0x00000080 /* Rx timer intr (ring 0) */
+#define E1000_ICR_ECCER         0x00400000 /* Uncorrectable ECC Error */
 #define E1000_ICR_INT_ASSERTED  0x80000000 /* If this bit asserted, the driver should claim the interrupt */
 #define E1000_ICR_RXQ0          0x00100000 /* Rx Queue 0 Interrupt */
 #define E1000_ICR_RXQ1          0x00200000 /* Rx Queue 1 Interrupt */
@@ -448,6 +456,7 @@
 #define E1000_IMS_RXSEQ     E1000_ICR_RXSEQ     /* Rx sequence error */
 #define E1000_IMS_RXDMT0    E1000_ICR_RXDMT0    /* Rx desc min. threshold */
 #define E1000_IMS_RXT0      E1000_ICR_RXT0      /* Rx timer intr */
+#define E1000_IMS_ECCER     E1000_ICR_ECCER     /* Uncorrectable ECC Error */
 #define E1000_IMS_RXQ0      E1000_ICR_RXQ0      /* Rx Queue 0 Interrupt */
 #define E1000_IMS_RXQ1      E1000_ICR_RXQ1      /* Rx Queue 1 Interrupt */
 #define E1000_IMS_TXQ0      E1000_ICR_TXQ0      /* Tx Queue 0 Interrupt */
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index bd5876171376..c96e6fcfdcbc 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -312,6 +312,8 @@ struct e1000_adapter {
 
 	struct napi_struct napi;
 
+	unsigned int uncorr_errors;	/* uncorrectable ECC errors */
+	unsigned int corr_errors;	/* correctable ECC errors */
 	unsigned int restart_queue;
 	u32 txd_cmd;
 
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index e3855bb10599..124821b49df6 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -109,6 +109,8 @@ static const struct e1000_stats e1000_gstrings_stats[] = {
 	E1000_STAT("rx_dma_failed", rx_dma_failed),
 	E1000_STAT("tx_dma_failed", tx_dma_failed),
 	E1000_STAT("rx_hwtstamp_cleared", rx_hwtstamp_cleared),
+	E1000_STAT("uncorr_ecc_errors", uncorr_errors),
+	E1000_STAT("corr_ecc_errors", corr_errors),
 };
 
 #define E1000_GLOBAL_STATS_LEN	ARRAY_SIZE(e1000_gstrings_stats)
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 84e6beb78718..4bd49be5915a 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -79,6 +79,7 @@ enum e1e_registers {
 #define E1000_POEMB	E1000_PHY_CTRL	/* PHY OEM Bits */
 	E1000_PBA      = 0x01000, /* Packet Buffer Allocation - RW */
 	E1000_PBS      = 0x01008, /* Packet Buffer Size */
+	E1000_PBECCSTS = 0x0100C, /* Packet Buffer ECC Status - RW */
 	E1000_EEMNGCTL = 0x01010, /* MNG EEprom Control */
 	E1000_EEWR     = 0x0102C, /* EEPROM Write Register - RW */
 	E1000_FLOP     = 0x0103C, /* FLASH Opcode Register */
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 50935ef48171..56cbfa7981eb 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -3704,6 +3704,17 @@ static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw)
 	if (hw->mac.type == e1000_ich8lan)
 		reg |= (E1000_RFCTL_IPV6_EX_DIS | E1000_RFCTL_NEW_IPV6_EXT_DIS);
 	ew32(RFCTL, reg);
+
+	/* Enable ECC on Lynxpoint */
+	if (hw->mac.type == e1000_pch_lpt) {
+		reg = er32(PBECCSTS);
+		reg |= E1000_PBECCSTS_ECC_ENABLE;
+		ew32(PBECCSTS, reg);
+
+		reg = er32(CTRL);
+		reg |= E1000_CTRL_MEHE;
+		ew32(CTRL, reg);
+	}
 }
 
 /**
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 34be756ee1e2..4c7e9fe23458 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -1780,6 +1780,23 @@ static irqreturn_t e1000_intr_msi(int irq, void *data)
 			mod_timer(&adapter->watchdog_timer, jiffies + 1);
 	}
 
+	/* Reset on uncorrectable ECC error */
+	if ((icr & E1000_ICR_ECCER) && (hw->mac.type == e1000_pch_lpt)) {
+		u32 pbeccsts = er32(PBECCSTS);
+
+		adapter->corr_errors +=
+		    pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK;
+		adapter->uncorr_errors +=
+		    (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >>
+		    E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT;
+
+		/* Do the reset outside of interrupt context */
+		schedule_work(&adapter->reset_task);
+
+		/* return immediately since reset is imminent */
+		return IRQ_HANDLED;
+	}
+
 	if (napi_schedule_prep(&adapter->napi)) {
 		adapter->total_tx_bytes = 0;
 		adapter->total_tx_packets = 0;
@@ -1843,6 +1860,23 @@ static irqreturn_t e1000_intr(int irq, void *data)
 			mod_timer(&adapter->watchdog_timer, jiffies + 1);
 	}
 
+	/* Reset on uncorrectable ECC error */
+	if ((icr & E1000_ICR_ECCER) && (hw->mac.type == e1000_pch_lpt)) {
+		u32 pbeccsts = er32(PBECCSTS);
+
+		adapter->corr_errors +=
+		    pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK;
+		adapter->uncorr_errors +=
+		    (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >>
+		    E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT;
+
+		/* Do the reset outside of interrupt context */
+		schedule_work(&adapter->reset_task);
+
+		/* return immediately since reset is imminent */
+		return IRQ_HANDLED;
+	}
+
 	if (napi_schedule_prep(&adapter->napi)) {
 		adapter->total_tx_bytes = 0;
 		adapter->total_tx_packets = 0;
@@ -2206,6 +2240,8 @@ static void e1000_irq_enable(struct e1000_adapter *adapter)
 	if (adapter->msix_entries) {
 		ew32(EIAC_82574, adapter->eiac_mask & E1000_EIAC_MASK_82574);
 		ew32(IMS, adapter->eiac_mask | E1000_IMS_OTHER | E1000_IMS_LSC);
+	} else if (hw->mac.type == e1000_pch_lpt) {
+		ew32(IMS, IMS_ENABLE_MASK | E1000_IMS_ECCER);
 	} else {
 		ew32(IMS, IMS_ENABLE_MASK);
 	}
@@ -4619,6 +4655,16 @@ static void e1000e_update_stats(struct e1000_adapter *adapter)
 	adapter->stats.mgptc += er32(MGTPTC);
 	adapter->stats.mgprc += er32(MGTPRC);
 	adapter->stats.mgpdc += er32(MGTPDC);
+
+	/* Correctable ECC Errors */
+	if (hw->mac.type == e1000_pch_lpt) {
+		u32 pbeccsts = er32(PBECCSTS);
+		adapter->corr_errors +=
+		    pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK;
+		adapter->uncorr_errors +=
+		    (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >>
+		    E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT;
+	}
 }
 
 /**
-- 
cgit v1.2.3


From 6e928b721c73817cd20f7dc7a303b3b7e57bff1d Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 12 Dec 2012 04:45:51 +0000
Subject: e1000e: prevent hardware from automatically configuring PHY on
 I217/I218

As done with the previous generation managed 82579, prevent the PHY from
being put into an unknown state by blocking the hardware from automatically
configuring the PHY as done with the previous generation managed 82579.
Instead, the driver should configure the PHY with contents of the EEPROM
image.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 22 +++++++---------------
 1 file changed, 7 insertions(+), 15 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 56cbfa7981eb..9a93223bd09a 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -363,10 +363,15 @@ static s32 e1000_init_phy_workarounds_pchlan(struct e1000_hw *hw)
 	s32 ret_val;
 	u16 phy_reg;
 
+	/* Gate automatic PHY configuration by hardware on managed and
+	 * non-managed 82579 and newer adapters.
+	 */
+	e1000_gate_hw_phy_config_ich8lan(hw, true);
+
 	ret_val = hw->phy.ops.acquire(hw);
 	if (ret_val) {
 		e_dbg("Failed to initialize PHY flow\n");
-		return ret_val;
+		goto out;
 	}
 
 	/* The MAC-PHY interconnect may be in SMBus mode.  If the PHY is
@@ -387,13 +392,6 @@ static s32 e1000_init_phy_workarounds_pchlan(struct e1000_hw *hw)
 
 		/* fall-through */
 	case e1000_pch2lan:
-		/* Gate automatic PHY configuration by hardware on
-		 * non-managed 82579
-		 */
-		if ((hw->mac.type == e1000_pch2lan) &&
-		    !(fwsm & E1000_ICH_FWSM_FW_VALID))
-			e1000_gate_hw_phy_config_ich8lan(hw, true);
-
 		if (e1000_phy_is_accessible_pchlan(hw)) {
 			if (hw->mac.type == e1000_pch_lpt) {
 				/* Unforce SMBus mode in PHY */
@@ -461,6 +459,7 @@ static s32 e1000_init_phy_workarounds_pchlan(struct e1000_hw *hw)
 	 */
 	ret_val = e1000e_phy_hw_reset_generic(hw);
 
+out:
 	/* Ungate automatic PHY configuration on non-managed 82579 */
 	if ((hw->mac.type == e1000_pch2lan) &&
 	    !(fwsm & E1000_ICH_FWSM_FW_VALID)) {
@@ -763,13 +762,6 @@ static s32 e1000_init_mac_params_ich8lan(struct e1000_hw *hw)
 	if (mac->type == e1000_ich8lan)
 		e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw, true);
 
-	/* Gate automatic PHY configuration by hardware on managed
-	 * 82579 and i217
-	 */
-	if ((mac->type == e1000_pch2lan || mac->type == e1000_pch_lpt) &&
-	    (er32(FWSM) & E1000_ICH_FWSM_FW_VALID))
-		e1000_gate_hw_phy_config_ich8lan(hw, true);
-
 	return 0;
 }
 
-- 
cgit v1.2.3


From fc915e93226cf00f4b8d1263ce2711959f9b1b76 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 29 Dec 2012 09:08:50 +0000
Subject: e1000e: remove prototype of non-existent function

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/e1000.h | 2 --
 1 file changed, 2 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index c96e6fcfdcbc..b8020b8b15c4 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -563,8 +563,6 @@ extern void e1000e_write_itr(struct e1000_adapter *adapter, u32 itr);
 
 extern unsigned int copybreak;
 
-extern char *e1000e_get_hw_dev_name(struct e1000_hw *hw);
-
 extern const struct e1000_info e1000_82571_info;
 extern const struct e1000_info e1000_82572_info;
 extern const struct e1000_info e1000_82573_info;
-- 
cgit v1.2.3


From bf67044bf86d9b5613cdba9d7d04deb4ea08892e Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Tue, 1 Jan 2013 16:00:01 +0000
Subject: e1000e: update copyright date

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/80003es2lan.c | 2 +-
 drivers/net/ethernet/intel/e1000e/82571.c       | 2 +-
 drivers/net/ethernet/intel/e1000e/Makefile      | 2 +-
 drivers/net/ethernet/intel/e1000e/defines.h     | 2 +-
 drivers/net/ethernet/intel/e1000e/e1000.h       | 2 +-
 drivers/net/ethernet/intel/e1000e/ethtool.c     | 2 +-
 drivers/net/ethernet/intel/e1000e/hw.h          | 2 +-
 drivers/net/ethernet/intel/e1000e/ich8lan.c     | 2 +-
 drivers/net/ethernet/intel/e1000e/mac.c         | 2 +-
 drivers/net/ethernet/intel/e1000e/manage.c      | 2 +-
 drivers/net/ethernet/intel/e1000e/netdev.c      | 4 ++--
 drivers/net/ethernet/intel/e1000e/nvm.c         | 2 +-
 drivers/net/ethernet/intel/e1000e/param.c       | 2 +-
 drivers/net/ethernet/intel/e1000e/phy.c         | 2 +-
 drivers/net/ethernet/intel/e1000e/ptp.c         | 2 +-
 15 files changed, 16 insertions(+), 16 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index e73c2c355993..97ff50e5eb5a 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index 587890d2d55e..e9d9bef12599 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/Makefile b/drivers/net/ethernet/intel/e1000e/Makefile
index 1da0faac0411..c2dcfcc10857 100644
--- a/drivers/net/ethernet/intel/e1000e/Makefile
+++ b/drivers/net/ethernet/intel/e1000e/Makefile
@@ -1,7 +1,7 @@
 ################################################################################
 #
 # Intel PRO/1000 Linux driver
-# Copyright(c) 1999 - 2012 Intel Corporation.
+# Copyright(c) 1999 - 2013 Intel Corporation.
 #
 # This program is free software; you can redistribute it and/or modify it
 # under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index f0452311c95a..3b997194ac3b 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index b8020b8b15c4..c7bc610a0b55 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 124821b49df6..4262b4d00609 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 4bd49be5915a..0a08b1438a18 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 9a93223bd09a..c25678dc2ddd 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index 0fa4c0656e09..d21f749a6492 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/manage.c b/drivers/net/ethernet/intel/e1000e/manage.c
index 6dc47beb3adc..4dae0dbda837 100644
--- a/drivers/net/ethernet/intel/e1000e/manage.c
+++ b/drivers/net/ethernet/intel/e1000e/manage.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 4c7e9fe23458..12784e804f42 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
@@ -7045,7 +7045,7 @@ static int __init e1000_init_module(void)
 	int ret;
 	pr_info("Intel(R) PRO/1000 Network Driver - %s\n",
 		e1000e_driver_version);
-	pr_info("Copyright(c) 1999 - 2012 Intel Corporation.\n");
+	pr_info("Copyright(c) 1999 - 2013 Intel Corporation.\n");
 	ret = pci_register_driver(&e1000_driver);
 
 	return ret;
diff --git a/drivers/net/ethernet/intel/e1000e/nvm.c b/drivers/net/ethernet/intel/e1000e/nvm.c
index 1e7882c7d6d4..84fecc268162 100644
--- a/drivers/net/ethernet/intel/e1000e/nvm.c
+++ b/drivers/net/ethernet/intel/e1000e/nvm.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/param.c b/drivers/net/ethernet/intel/e1000e/param.c
index b29a8a5116a8..19c40d6f53cc 100644
--- a/drivers/net/ethernet/intel/e1000e/param.c
+++ b/drivers/net/ethernet/intel/e1000e/param.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 28b38ff37e84..70f759399355 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/ptp.c b/drivers/net/ethernet/intel/e1000e/ptp.c
index 32da00c0cbc9..6b8df6587858 100644
--- a/drivers/net/ethernet/intel/e1000e/ptp.c
+++ b/drivers/net/ethernet/intel/e1000e/ptp.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
-- 
cgit v1.2.3


From ed1a42656aa794aa3d6edf5ca83f98835701dc41 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Fri, 4 Jan 2013 09:51:36 +0000
Subject: e1000e: correct maximum frame size on i217/i218

The largest jumbo frame supported by the i217 and i218 hardware is 9018.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index c25678dc2ddd..e0f41f0b5fe6 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -4633,7 +4633,7 @@ const struct e1000_info e1000_pch_lpt_info = {
 	.flags2			= FLAG2_HAS_PHY_STATS
 				  | FLAG2_HAS_EEE,
 	.pba			= 26,
-	.max_hw_frame_size	= DEFAULT_JUMBO,
+	.max_hw_frame_size	= 9018,
 	.get_variants		= e1000_get_variants_ich8lan,
 	.mac_ops		= &ich8_mac_ops,
 	.phy_ops		= &ich8_phy_ops,
-- 
cgit v1.2.3


From 4e03510b4779851db7e9153368d1f856e66ea239 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Fri, 4 Jan 2013 09:53:19 +0000
Subject: e1000e: fix PHY init workarounds for i217/i218

Toggling the LANPHYPC Value bit cycles the power on the PHY and sets it
back to power-on defaults.  This includes setting it's MAC-PHY messaging
mode to use the PCIe-like interconnect, so the MAC must also be set back
from SMBus mode to PCIe mode otherwise the PHY can be inaccessible.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 9 +++++++++
 1 file changed, 9 insertions(+)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index e0f41f0b5fe6..3f3477ffd46c 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -426,6 +426,15 @@ static s32 e1000_init_phy_workarounds_pchlan(struct e1000_hw *hw)
 		mac_reg |= E1000_FEXTNVM3_PHY_CFG_COUNTER_50MSEC;
 		ew32(FEXTNVM3, mac_reg);
 
+		if (hw->mac.type == e1000_pch_lpt) {
+			/* Toggling LANPHYPC brings the PHY out of SMBus mode
+			 * So ensure that the MAC is also out of SMBus mode
+			 */
+			mac_reg = er32(CTRL_EXT);
+			mac_reg &= ~E1000_CTRL_EXT_FORCE_SMBUS;
+			ew32(CTRL_EXT, mac_reg);
+		}
+
 		/* Toggle LANPHYPC Value bit */
 		mac_reg = er32(CTRL);
 		mac_reg |= E1000_CTRL_LANPHYPC_OVERRIDE;
-- 
cgit v1.2.3


From d394998072d05fe694e85ae544e530da964da9f8 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Fri, 4 Jan 2013 09:54:11 +0000
Subject: e1000e: remove definition of struct which is no longer used

The e1000e driver has been converted to use extended descriptors instead of
the older legacy descriptor type.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/hw.h | 10 ----------
 1 file changed, 10 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 0a08b1438a18..a10de4d122cc 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -542,16 +542,6 @@ enum e1000_serdes_link_state {
 	e1000_serdes_link_forced_up
 };
 
-/* Receive Descriptor */
-struct e1000_rx_desc {
-	__le64 buffer_addr; /* Address of the descriptor's data buffer */
-	__le16 length;      /* Length of data DMAed into data buffer */
-	__le16 csum;	/* Packet checksum */
-	u8  status;      /* Descriptor status */
-	u8  errors;      /* Descriptor Errors */
-	__le16 special;
-};
-
 /* Receive Descriptor - Extended */
 union e1000_rx_desc_extended {
 	struct {
-- 
cgit v1.2.3


From 9d57088be9f1d166d6ca311218611a51cd3ecfc2 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Fri, 4 Jan 2013 10:06:03 +0000
Subject: e1000e: add comment to spinlock_t definition

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/e1000.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index c7bc610a0b55..e6b94835291e 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -372,7 +372,7 @@ struct e1000_adapter {
 	/* structs defined in e1000_hw.h */
 	struct e1000_hw hw;
 
-	spinlock_t stats64_lock;
+	spinlock_t stats64_lock;	/* protects statistics counters */
 	struct e1000_hw_stats stats;
 	struct e1000_phy_info phy_info;
 	struct e1000_phy_stats phy_stats;
-- 
cgit v1.2.3


From 1f96012d34670202c135828482fffbf603b4dce0 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 5 Jan 2013 03:06:54 +0000
Subject: e1000e: cleanup: remove unnecessary function prototypes

...and cleanup some whitespace in other prototypes.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/80003es2lan.c | 9 ++++-----
 drivers/net/ethernet/intel/e1000e/82571.c       | 2 --
 drivers/net/ethernet/intel/e1000e/ich8lan.c     | 5 +----
 drivers/net/ethernet/intel/e1000e/phy.c         | 3 +--
 4 files changed, 6 insertions(+), 13 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index 97ff50e5eb5a..a2b5b44cfe2b 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -111,11 +111,10 @@ static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw);
 static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw);
 static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw);
 static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex);
-static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw);
-static s32  e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
-                                            u16 *data);
-static s32  e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
-                                             u16 data);
+static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+					   u16 *data);
+static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+					    u16 data);
 static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw);
 
 /**
diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index e9d9bef12599..c2c23d26f440 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -67,9 +67,7 @@ static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
 				      u16 words, u16 *data);
 static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw);
 static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw);
-static s32 e1000_setup_link_82571(struct e1000_hw *hw);
 static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw);
-static void e1000_clear_vfta_82571(struct e1000_hw *hw);
 static bool e1000_check_mng_mode_82574(struct e1000_hw *hw);
 static s32 e1000_led_on_82574(struct e1000_hw *hw);
 static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw);
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 3f3477ffd46c..3795ac6dae22 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -237,7 +237,6 @@ union ich8_flash_protected_range {
 	u32 regval;
 };
 
-static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw);
 static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw);
 static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw);
 static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank);
@@ -249,9 +248,7 @@ static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset,
 					 u16 *data);
 static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
 					 u8 size, u16 *data);
-static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw);
 static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw);
-static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw);
 static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw);
 static s32 e1000_led_on_ich8lan(struct e1000_hw *hw);
 static s32 e1000_led_off_ich8lan(struct e1000_hw *hw);
@@ -263,7 +260,7 @@ static s32 e1000_led_off_pchlan(struct e1000_hw *hw);
 static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active);
 static void e1000_power_down_phy_copper_ich8lan(struct e1000_hw *hw);
 static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw);
-static s32  e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link);
+static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link);
 static s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw);
 static bool e1000_check_mng_mode_ich8lan(struct e1000_hw *hw);
 static bool e1000_check_mng_mode_pchlan(struct e1000_hw *hw);
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 70f759399355..3b9712134409 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -32,12 +32,11 @@ static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw);
 static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw);
 static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active);
 static s32 e1000_wait_autoneg(struct e1000_hw *hw);
-static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg);
 static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
 					  u16 *data, bool read, bool page_set);
 static u32 e1000_get_phy_addr_for_hv_page(u32 page);
 static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
-                                          u16 *data, bool read);
+					  u16 *data, bool read);
 
 /* Cable length tables */
 static const u16 e1000_m88_cable_length_table[] = {
-- 
cgit v1.2.3


From 7dbbe5d5a5073d590790007d5b98d7fd51fd2ff5 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 5 Jan 2013 05:08:31 +0000
Subject: e1000e: do not ignore variables which get set a value

Static analysis with cppcheck has shown a few instances of a variable which
is assigned a value that is never used.  A number of these are the return
status of various driver function calls which should be passed back to the
caller of the current function.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/80003es2lan.c | 5 +++++
 drivers/net/ethernet/intel/e1000e/82571.c       | 8 +++++---
 drivers/net/ethernet/intel/e1000e/ich8lan.c     | 5 +++--
 drivers/net/ethernet/intel/e1000e/phy.c         | 2 +-
 4 files changed, 14 insertions(+), 6 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index a2b5b44cfe2b..aa5e4cf90a58 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -773,6 +773,9 @@ static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
 	ctrl = er32(CTRL);
 
 	ret_val = e1000_acquire_phy_80003es2lan(hw);
+	if (ret_val)
+		return ret_val;
+
 	e_dbg("Issuing a global reset to MAC\n");
 	ew32(CTRL, ctrl | E1000_CTRL_RST);
 	e1000_release_phy_80003es2lan(hw);
@@ -832,6 +835,8 @@ static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
 
 	/* Setup link and flow control */
 	ret_val = mac->ops.setup_link(hw);
+	if (ret_val)
+		return ret_val;
 
 	/* Disable IBIST slave mode (far-end loopback) */
 	e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index c2c23d26f440..d48143fefbfe 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -554,16 +554,14 @@ static s32 e1000_get_hw_semaphore_82573(struct e1000_hw *hw)
 	s32 i = 0;
 
 	extcnf_ctrl = er32(EXTCNF_CTRL);
-	extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
 	do {
+		extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
 		ew32(EXTCNF_CTRL, extcnf_ctrl);
 		extcnf_ctrl = er32(EXTCNF_CTRL);
 
 		if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
 			break;
 
-		extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
-
 		usleep_range(2000, 4000);
 		i++;
 	} while (i < MDIO_OWNERSHIP_TIMEOUT);
@@ -935,6 +933,8 @@ static s32 e1000_set_d0_lplu_state_82571(struct e1000_hw *hw, bool active)
 
 		/* When LPLU is enabled, we should disable SmartSpeed */
 		ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
+		if (ret_val)
+			return ret_val;
 		data &= ~IGP01E1000_PSCFR_SMART_SPEED;
 		ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
 		if (ret_val)
@@ -1797,6 +1797,8 @@ static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw)
 			if (ret_val)
 				return ret_val;
 			ret_val = e1000e_update_nvm_checksum(hw);
+			if (ret_val)
+				return ret_val;
 		}
 	}
 
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 3795ac6dae22..13f8fa0984e8 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -2342,6 +2342,8 @@ static s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active)
 
 		/* When LPLU is enabled, we should disable SmartSpeed */
 		ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
+		if (ret_val)
+			return ret_val;
 		data &= ~IGP01E1000_PSCFR_SMART_SPEED;
 		ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
 		if (ret_val)
@@ -4053,8 +4055,7 @@ void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw)
 	if (ret_val)
 		return;
 	reg_data &= ~E1000_KMRNCTRLSTA_DIAG_NELPBK;
-	ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET,
-				       reg_data);
+	e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, reg_data);
 }
 
 /**
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 3b9712134409..b4aaf69f4410 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -3332,7 +3332,7 @@ s32 e1000_get_cable_length_82577(struct e1000_hw *hw)
 	         I82577_DSTATUS_CABLE_LENGTH_SHIFT;
 
 	if (length == E1000_CABLE_LENGTH_UNDEFINED)
-		ret_val = -E1000_ERR_PHY;
+		return -E1000_ERR_PHY;
 
 	phy->cable_length = length;
 
-- 
cgit v1.2.3


From 70806a7fd1ae8942675bb2d415899e9e64440505 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 5 Jan 2013 05:08:37 +0000
Subject: e1000e: cleanup: do not assign a variable a value when not necessary

Static analysis with cppcheck has shown a few instances of a variable
being reassigned a value before the old one has been used.  None of these
ever require the old value to be used so remove the old values.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/80003es2lan.c |  8 ++++----
 drivers/net/ethernet/intel/e1000e/82571.c       |  6 +++---
 drivers/net/ethernet/intel/e1000e/ethtool.c     |  2 +-
 drivers/net/ethernet/intel/e1000e/ich8lan.c     | 10 +++++-----
 drivers/net/ethernet/intel/e1000e/mac.c         |  2 +-
 drivers/net/ethernet/intel/e1000e/netdev.c      |  6 +++---
 drivers/net/ethernet/intel/e1000e/phy.c         |  6 +++---
 7 files changed, 20 insertions(+), 20 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index aa5e4cf90a58..ae96facee8fe 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -695,7 +695,7 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
 static s32 e1000_get_cable_length_80003es2lan(struct e1000_hw *hw)
 {
 	struct e1000_phy_info *phy = &hw->phy;
-	s32 ret_val = 0;
+	s32 ret_val;
 	u16 phy_data, index;
 
 	ret_val = e1e_rphy(hw, GG82563_PHY_DSP_DISTANCE, &phy_data);
@@ -1276,7 +1276,7 @@ static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
 					   u16 *data)
 {
 	u32 kmrnctrlsta;
-	s32 ret_val = 0;
+	s32 ret_val;
 
 	ret_val = e1000_acquire_mac_csr_80003es2lan(hw);
 	if (ret_val)
@@ -1311,7 +1311,7 @@ static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
 					    u16 data)
 {
 	u32 kmrnctrlsta;
-	s32 ret_val = 0;
+	s32 ret_val;
 
 	ret_val = e1000_acquire_mac_csr_80003es2lan(hw);
 	if (ret_val)
@@ -1335,7 +1335,7 @@ static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
  **/
 static s32 e1000_read_mac_addr_80003es2lan(struct e1000_hw *hw)
 {
-	s32 ret_val = 0;
+	s32 ret_val;
 
 	/* If there's an alternate MAC address place it in RAR0
 	 * so that it will override the Si installed default perm
diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index d48143fefbfe..0f55d79afe39 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -1397,7 +1397,7 @@ bool e1000_check_phy_82574(struct e1000_hw *hw)
 {
 	u16 status_1kbt = 0;
 	u16 receive_errors = 0;
-	s32 ret_val = 0;
+	s32 ret_val;
 
 	/* Read PHY Receive Error counter first, if its is max - all F's then
 	 * read the Base1000T status register If both are max then PHY is hung.
@@ -1542,7 +1542,7 @@ static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw)
 
 	ctrl = er32(CTRL);
 	status = er32(STATUS);
-	rxcw = er32(RXCW);
+	er32(RXCW);
 	/* SYNCH bit and IV bit are sticky */
 	udelay(10);
 	rxcw = er32(RXCW);
@@ -1812,7 +1812,7 @@ static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw)
 static s32 e1000_read_mac_addr_82571(struct e1000_hw *hw)
 {
 	if (hw->mac.type == e1000_82571) {
-		s32 ret_val = 0;
+		s32 ret_val;
 
 		/* If there's an alternate MAC address place it in RAR0
 		 * so that it will override the Si installed default perm
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 4262b4d00609..6ab949d0b39b 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -1405,7 +1405,7 @@ static int e1000_set_82571_fiber_loopback(struct e1000_adapter *adapter)
 {
 	struct e1000_hw *hw = &adapter->hw;
 	u32 ctrl = er32(CTRL);
-	int link = 0;
+	int link;
 
 	/* special requirements for 82571/82572 fiber adapters */
 
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 13f8fa0984e8..87676b652edc 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -485,7 +485,7 @@ out:
 static s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw)
 {
 	struct e1000_phy_info *phy = &hw->phy;
-	s32 ret_val = 0;
+	s32 ret_val;
 
 	phy->addr                     = 1;
 	phy->reset_delay_us           = 100;
@@ -783,7 +783,7 @@ static s32 e1000_init_mac_params_ich8lan(struct e1000_hw *hw)
 static s32 __e1000_access_emi_reg_locked(struct e1000_hw *hw, u16 address,
 					 u16 *data, bool read)
 {
-	s32 ret_val = 0;
+	s32 ret_val;
 
 	ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR, address);
 	if (ret_val)
@@ -1387,7 +1387,7 @@ static s32 e1000_write_smbus_addr(struct e1000_hw *hw)
 	u32 strap = er32(STRAP);
 	u32 freq = (strap & E1000_STRAP_SMT_FREQ_MASK) >>
 	    E1000_STRAP_SMT_FREQ_SHIFT;
-	s32 ret_val = 0;
+	s32 ret_val;
 
 	strap &= E1000_STRAP_SMBUS_ADDRESS_MASK;
 
@@ -1623,7 +1623,7 @@ release:
  **/
 s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable)
 {
-	s32 ret_val = 0;
+	s32 ret_val;
 	u32 ctrl_reg = 0;
 	u32 ctrl_ext = 0;
 	u32 reg = 0;
@@ -2284,7 +2284,7 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
  **/
 static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active)
 {
-	s32 ret_val = 0;
+	s32 ret_val;
 	u16 oem_reg;
 
 	ret_val = e1e_rphy(hw, HV_OEM_BITS, &oem_reg);
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index d21f749a6492..0709f49f0335 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -165,7 +165,7 @@ void e1000e_init_rx_addrs(struct e1000_hw *hw, u16 rar_count)
 s32 e1000_check_alt_mac_addr_generic(struct e1000_hw *hw)
 {
 	u32 i;
-	s32 ret_val = 0;
+	s32 ret_val;
 	u16 offset, nvm_alt_mac_addr_offset, nvm_data;
 	u8 alt_mac_addr[ETH_ALEN];
 
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 12784e804f42..e386e95102f4 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -3660,8 +3660,8 @@ static int e1000e_config_hwtstamp(struct e1000_adapter *adapter)
 	e1e_flush();
 
 	/* Clear TSYNCRXCTL_VALID & TSYNCTXCTL_VALID bit */
-	regval = er32(RXSTMPH);
-	regval = er32(TXSTMPH);
+	er32(RXSTMPH);
+	er32(TXSTMPH);
 
 	/* Get and set the System Time Register SYSTIM base frequency */
 	ret_val = e1000e_get_base_timinca(adapter, &regval);
@@ -5834,7 +5834,7 @@ static int e1000_init_phy_wakeup(struct e1000_adapter *adapter, u32 wufc)
 	struct e1000_hw *hw = &adapter->hw;
 	u32 i, mac_reg;
 	u16 phy_reg, wuc_enable;
-	int retval = 0;
+	int retval;
 
 	/* copy MAC RARs to PHY RARs */
 	e1000_copy_rx_addrs_to_phy_ich8lan(hw);
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index b4aaf69f4410..44fb432f3c10 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -2671,7 +2671,7 @@ s32 e1000_enable_phy_wakeup_reg_access_bm(struct e1000_hw *hw, u16 *phy_reg)
  **/
 s32 e1000_disable_phy_wakeup_reg_access_bm(struct e1000_hw *hw, u16 *phy_reg)
 {
-	s32 ret_val = 0;
+	s32 ret_val;
 
 	/* Select Port Control Registers page */
 	ret_val = e1000_set_page_igp(hw, (BM_PORT_CTRL_PAGE << IGP_PAGE_SHIFT));
@@ -3103,8 +3103,8 @@ static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
                                           u16 *data, bool read)
 {
 	s32 ret_val;
-	u32 addr_reg = 0;
-	u32 data_reg = 0;
+	u32 addr_reg;
+	u32 data_reg;
 
 	/* This takes care of the difference with desktop vs mobile phy */
 	addr_reg = (hw->phy.type == e1000_phy_82578) ?
-- 
cgit v1.2.3


From 7de89f058ec2c58ef16582e4efadeb33d711c9e1 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 5 Jan 2013 08:06:03 +0000
Subject: e1000e: cleanup: remove e1000_set_d0_lplu_state()

Replace the function e1000_set_d0_lplu_state() with the contents of it
coded in place of the single call to the function.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/phy.c | 33 ++++++---------------------------
 1 file changed, 6 insertions(+), 27 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 44fb432f3c10..73d7813b98af 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -30,7 +30,6 @@
 
 static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw);
 static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw);
-static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active);
 static s32 e1000_wait_autoneg(struct e1000_hw *hw);
 static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
 					  u16 *data, bool read, bool page_set);
@@ -894,10 +893,12 @@ s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw)
 	msleep(100);
 
 	/* disable lplu d0 during driver init */
-	ret_val = e1000_set_d0_lplu_state(hw, false);
-	if (ret_val) {
-		e_dbg("Error Disabling LPLU D0\n");
-		return ret_val;
+	if (hw->phy.ops.set_d0_lplu_state) {
+		ret_val = hw->phy.ops.set_d0_lplu_state(hw, false);
+		if (ret_val) {
+			e_dbg("Error Disabling LPLU D0\n");
+			return ret_val;
+		}
 	}
 	/* Configure mdi-mdix settings */
 	ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CTRL, &data);
@@ -2819,28 +2820,6 @@ s32 e1000e_commit_phy(struct e1000_hw *hw)
 	return 0;
 }
 
-/**
- *  e1000_set_d0_lplu_state - Sets low power link up state for D0
- *  @hw: pointer to the HW structure
- *  @active: boolean used to enable/disable lplu
- *
- *  Success returns 0, Failure returns 1
- *
- *  The low power link up (lplu) state is set to the power management level D0
- *  and SmartSpeed is disabled when active is true, else clear lplu for D0
- *  and enable Smartspeed.  LPLU and Smartspeed are mutually exclusive.  LPLU
- *  is used during Dx states where the power conservation is most important.
- *  During driver activity, SmartSpeed should be enabled so performance is
- *  maintained.  This is a function pointer entry point called by drivers.
- **/
-static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
-{
-	if (hw->phy.ops.set_d0_lplu_state)
-		return hw->phy.ops.set_d0_lplu_state(hw, active);
-
-	return 0;
-}
-
 /**
  *  __e1000_read_phy_reg_hv -  Read HV PHY register
  *  @hw: pointer to the HW structure
-- 
cgit v1.2.3


From c2c6629ba3f57d19b1385554b7fadb671bc7ab30 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 5 Jan 2013 08:06:08 +0000
Subject: e1000e: cleanup: remove e1000_force_speed_duplex()

Remove the function e1000_force_speed_duplex() and replace the single call
to it with the same function pointer that it would call.  The function
pointer is always set so there is no risk of a NULL pointer dereference.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/phy.c | 18 +-----------------
 1 file changed, 1 insertion(+), 17 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 73d7813b98af..81fba6cfb3a4 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -29,7 +29,6 @@
 #include "e1000.h"
 
 static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw);
-static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw);
 static s32 e1000_wait_autoneg(struct e1000_hw *hw);
 static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
 					  u16 *data, bool read, bool page_set);
@@ -1196,7 +1195,7 @@ s32 e1000e_setup_copper_link(struct e1000_hw *hw)
 		 * depending on user settings.
 		 */
 		e_dbg("Forcing Speed and Duplex\n");
-		ret_val = e1000_phy_force_speed_duplex(hw);
+		ret_val = hw->phy.ops.force_speed_duplex(hw);
 		if (ret_val) {
 			e_dbg("Error Forcing Speed and Duplex\n");
 			return ret_val;
@@ -2283,21 +2282,6 @@ static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw)
 	return 0;
 }
 
-/**
- *  e1000_phy_force_speed_duplex - Generic force PHY speed/duplex
- *  @hw: pointer to the HW structure
- *
- *  When the silicon family has not implemented a forced speed/duplex
- *  function for the PHY, simply return 0.
- **/
-static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
-{
-	if (hw->phy.ops.force_speed_duplex)
-		return hw->phy.ops.force_speed_duplex(hw);
-
-	return 0;
-}
-
 /**
  *  e1000e_get_phy_type_from_id - Get PHY type from id
  *  @phy_id: phy_id read from the phy
-- 
cgit v1.2.3


From fe90849f76de7cd584e8c6c38b076cd366415994 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 5 Jan 2013 08:06:14 +0000
Subject: e1000e: cleanup: rename e1000_get_cfg_done()

In keeping with the e1000e driver function naming convention, the subject
function is renamed to indicate it is generic, i.e. it is applicable to
more than just a single MAC family (e.g. 80003es2lan, 82571, ich8lan).

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/82571.c   | 4 ++--
 drivers/net/ethernet/intel/e1000e/e1000.h   | 2 +-
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 2 +-
 drivers/net/ethernet/intel/e1000e/phy.c     | 4 ++--
 4 files changed, 6 insertions(+), 6 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index 0f55d79afe39..076938c87a26 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -1940,7 +1940,7 @@ static const struct e1000_phy_operations e82_phy_ops_m88 = {
 	.check_reset_block	= e1000e_check_reset_block_generic,
 	.commit			= e1000e_phy_sw_reset,
 	.force_speed_duplex	= e1000e_phy_force_speed_duplex_m88,
-	.get_cfg_done		= e1000e_get_cfg_done,
+	.get_cfg_done		= e1000e_get_cfg_done_generic,
 	.get_cable_length	= e1000e_get_cable_length_m88,
 	.get_info		= e1000e_get_phy_info_m88,
 	.read_reg		= e1000e_read_phy_reg_m88,
@@ -1958,7 +1958,7 @@ static const struct e1000_phy_operations e82_phy_ops_bm = {
 	.check_reset_block	= e1000e_check_reset_block_generic,
 	.commit			= e1000e_phy_sw_reset,
 	.force_speed_duplex	= e1000e_phy_force_speed_duplex_m88,
-	.get_cfg_done		= e1000e_get_cfg_done,
+	.get_cfg_done		= e1000e_get_cfg_done_generic,
 	.get_cable_length	= e1000e_get_cable_length_m88,
 	.get_info		= e1000e_get_phy_info_m88,
 	.read_reg		= e1000e_read_phy_reg_bm2,
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index e6b94835291e..115656e1dc46 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -654,7 +654,7 @@ extern s32 e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset,
                                            u16 data);
 extern s32 e1000e_phy_sw_reset(struct e1000_hw *hw);
 extern s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw);
-extern s32 e1000e_get_cfg_done(struct e1000_hw *hw);
+extern s32 e1000e_get_cfg_done_generic(struct e1000_hw *hw);
 extern s32 e1000e_get_cable_length_m88(struct e1000_hw *hw);
 extern s32 e1000e_get_phy_info_m88(struct e1000_hw *hw);
 extern s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data);
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 87676b652edc..edd5996b897a 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -4378,7 +4378,7 @@ static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw)
 	u32 bank = 0;
 	u32 status;
 
-	e1000e_get_cfg_done(hw);
+	e1000e_get_cfg_done_generic(hw);
 
 	/* Wait for indication from h/w that it has completed basic config */
 	if (hw->mac.type >= e1000_ich10lan) {
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 81fba6cfb3a4..37a85d4bb7d0 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -2169,13 +2169,13 @@ s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw)
 }
 
 /**
- *  e1000e_get_cfg_done - Generic configuration done
+ *  e1000e_get_cfg_done_generic - Generic configuration done
  *  @hw: pointer to the HW structure
  *
  *  Generic function to wait 10 milli-seconds for configuration to complete
  *  and return success.
  **/
-s32 e1000e_get_cfg_done(struct e1000_hw *hw)
+s32 e1000e_get_cfg_done_generic(struct e1000_hw *hw)
 {
 	mdelay(10);
 
-- 
cgit v1.2.3


From 84c1befe341d71ed1b878afa28bb637a0b459161 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 5 Jan 2013 08:06:19 +0000
Subject: e1000e: cleanup: remove e1000_get_phy_cfg_done()

Remove the function e1000_get_phy_cfg_done() and replace the single call
to it with the same function pointer that it would call.  The function
pointer is always set so there is no risk of a NULL pointer dereference.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/phy.c | 20 +-------------------
 1 file changed, 1 insertion(+), 19 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 37a85d4bb7d0..3cf627be9776 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -28,7 +28,6 @@
 
 #include "e1000.h"
 
-static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw);
 static s32 e1000_wait_autoneg(struct e1000_hw *hw);
 static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
 					  u16 *data, bool read, bool page_set);
@@ -2165,7 +2164,7 @@ s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw)
 
 	phy->ops.release(hw);
 
-	return e1000_get_phy_cfg_done(hw);
+	return phy->ops.get_cfg_done(hw);
 }
 
 /**
@@ -2265,23 +2264,6 @@ s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw)
 	return 0;
 }
 
-/* Internal function pointers */
-
-/**
- *  e1000_get_phy_cfg_done - Generic PHY configuration done
- *  @hw: pointer to the HW structure
- *
- *  Return success if silicon family did not implement a family specific
- *  get_cfg_done function.
- **/
-static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw)
-{
-	if (hw->phy.ops.get_cfg_done)
-		return hw->phy.ops.get_cfg_done(hw);
-
-	return 0;
-}
-
 /**
  *  e1000e_get_phy_type_from_id - Get PHY type from id
  *  @phy_id: phy_id read from the phy
-- 
cgit v1.2.3


From dde3a5745cd27167653feb2e7e9fa0e3631e91ce Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 5 Jan 2013 08:06:24 +0000
Subject: e1000e: cleanup: remove e1000_get_cable_length()

Remove the function e1000_get_cable_length() and replace the two calls
to it with the same function pointer that it would call.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/e1000.h | 5 -----
 drivers/net/ethernet/intel/e1000e/phy.c   | 4 ++--
 2 files changed, 2 insertions(+), 7 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 115656e1dc46..896eacc80433 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -737,11 +737,6 @@ static inline s32 e1e_wphy_locked(struct e1000_hw *hw, u32 offset, u16 data)
 	return hw->phy.ops.write_reg_locked(hw, offset, data);
 }
 
-static inline s32 e1000_get_cable_length(struct e1000_hw *hw)
-{
-	return hw->phy.ops.get_cable_length(hw);
-}
-
 extern s32 e1000e_acquire_nvm(struct e1000_hw *hw);
 extern s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
 extern s32 e1000e_update_nvm_checksum_generic(struct e1000_hw *hw);
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 3cf627be9776..c4bfbd61d895 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -1960,7 +1960,7 @@ s32 e1000e_get_phy_info_m88(struct e1000_hw *hw)
 	phy->is_mdix = !!(phy_data & M88E1000_PSSR_MDIX);
 
 	if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) {
-		ret_val = e1000_get_cable_length(hw);
+		ret_val = hw->phy.ops.get_cable_length(hw);
 		if (ret_val)
 			return ret_val;
 
@@ -2024,7 +2024,7 @@ s32 e1000e_get_phy_info_igp(struct e1000_hw *hw)
 
 	if ((data & IGP01E1000_PSSR_SPEED_MASK) ==
 	    IGP01E1000_PSSR_SPEED_1000MBPS) {
-		ret_val = e1000_get_cable_length(hw);
+		ret_val = phy->ops.get_cable_length(hw);
 		if (ret_val)
 			return ret_val;
 
-- 
cgit v1.2.3


From 6b598e1eac68b07ebb831258e0667f5ba2834822 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 23 Jan 2013 06:50:05 +0000
Subject: e1000e: cleanup: remove e1000e_commit_phy()

Remove the function e1000e_commit_phy() and replace the few calls to it
with the same function pointer that it would call.  The function pointer is
almost always set for the devices that access these code paths so there is
no risk of a NULL pointer dereference; for the few instances where the
function pointer might not be set (i.e. can be called for the few devices
which do not have this function pointer set), check for a valid function
pointer.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/80003es2lan.c |  2 +-
 drivers/net/ethernet/intel/e1000e/e1000.h       |  2 --
 drivers/net/ethernet/intel/e1000e/ethtool.c     |  5 ++--
 drivers/net/ethernet/intel/e1000e/phy.c         | 35 +++++++++----------------
 4 files changed, 16 insertions(+), 28 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index ae96facee8fe..3f27546baaa7 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -1010,7 +1010,7 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
 		return ret_val;
 
 	/* SW Reset the PHY so all changes take effect */
-	ret_val = e1000e_commit_phy(hw);
+	ret_val = hw->phy.ops.commit(hw);
 	if (ret_val) {
 		e_dbg("Error Resetting the PHY\n");
 		return ret_val;
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 896eacc80433..4ffb62bd0b75 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -579,8 +579,6 @@ extern const struct e1000_info e1000_es2_info;
 extern s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
 					 u32 pba_num_size);
 
-extern s32  e1000e_commit_phy(struct e1000_hw *hw);
-
 extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
 
 extern bool e1000e_get_laa_state_82571(struct e1000_hw *hw);
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 6ab949d0b39b..58df18c2efc2 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -1321,7 +1321,7 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 		phy_reg |= 0x006;
 		e1e_wphy(hw, PHY_REG(2, 21), phy_reg);
 		/* Assert SW reset for above settings to take effect */
-		e1000e_commit_phy(hw);
+		hw->phy.ops.commit(hw);
 		mdelay(1);
 		/* Force Full Duplex */
 		e1e_rphy(hw, PHY_REG(769, 16), &phy_reg);
@@ -1542,7 +1542,8 @@ static void e1000_loopback_cleanup(struct e1000_adapter *adapter)
 		if (phy_reg & MII_CR_LOOPBACK) {
 			phy_reg &= ~MII_CR_LOOPBACK;
 			e1e_wphy(hw, PHY_CONTROL, phy_reg);
-			e1000e_commit_phy(hw);
+			if (hw->phy.ops.commit)
+				hw->phy.ops.commit(hw);
 		}
 		break;
 	}
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index c4bfbd61d895..cddfc6b92f75 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -788,7 +788,7 @@ s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw)
 			if (ret_val)
 				return ret_val;
 			/* Commit the changes. */
-			ret_val = e1000e_commit_phy(hw);
+			ret_val = phy->ops.commit(hw);
 			if (ret_val) {
 				e_dbg("Error committing the PHY changes\n");
 				return ret_val;
@@ -844,10 +844,12 @@ s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw)
 	}
 
 	/* Commit the changes. */
-	ret_val = e1000e_commit_phy(hw);
-	if (ret_val) {
-		e_dbg("Error committing the PHY changes\n");
-		return ret_val;
+	if (phy->ops.commit) {
+		ret_val = phy->ops.commit(hw);
+		if (ret_val) {
+			e_dbg("Error committing the PHY changes\n");
+			return ret_val;
+		}
 	}
 
 	if (phy->type == e1000_phy_82578) {
@@ -1324,9 +1326,11 @@ s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw)
 		return ret_val;
 
 	/* Reset the phy to commit changes. */
-	ret_val = e1000e_commit_phy(hw);
-	if (ret_val)
-		return ret_val;
+	if (hw->phy.ops.commit) {
+		ret_val = hw->phy.ops.commit(hw);
+		if (ret_val)
+			return ret_val;
+	}
 
 	if (phy->autoneg_wait_to_complete) {
 		e_dbg("Waiting for forced speed/duplex link on M88 phy.\n");
@@ -2771,21 +2775,6 @@ void e1000_power_down_phy_copper(struct e1000_hw *hw)
 	usleep_range(1000, 2000);
 }
 
-/**
- *  e1000e_commit_phy - Soft PHY reset
- *  @hw: pointer to the HW structure
- *
- *  Performs a soft PHY reset on those that apply. This is a function pointer
- *  entry point called by drivers.
- **/
-s32 e1000e_commit_phy(struct e1000_hw *hw)
-{
-	if (hw->phy.ops.commit)
-		return hw->phy.ops.commit(hw);
-
-	return 0;
-}
-
 /**
  *  __e1000_read_phy_reg_hv -  Read HV PHY register
  *  @hw: pointer to the HW structure
-- 
cgit v1.2.3


From c3d2dbf403367eb5c17f044aa74b772508d745c1 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 9 Jan 2013 01:20:46 +0000
Subject: e1000e: correct maximum frame size on 82579

The largest jumbo frame supported by the 82579 hardware is 9018.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index edd5996b897a..58547b8abe3d 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -4620,7 +4620,7 @@ const struct e1000_info e1000_pch2_info = {
 	.flags2			= FLAG2_HAS_PHY_STATS
 				  | FLAG2_HAS_EEE,
 	.pba			= 26,
-	.max_hw_frame_size	= DEFAULT_JUMBO,
+	.max_hw_frame_size	= 9018,
 	.get_variants		= e1000_get_variants_ich8lan,
 	.mac_ops		= &ich8_mac_ops,
 	.phy_ops		= &ich8_phy_ops,
-- 
cgit v1.2.3


From 3e35d9918cbbc224f88da4dd19cd90b2cd4f765e Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 07:25:22 +0000
Subject: e1000e: adjust PM QoS request

It has been found that devices other than 82579 (a.k.a. e1000_pch2lan)
suffer from dropped transactions on platforms with deep C-states when
jumbo frames are enabled.  For example, LOMs on ICH9- and ICH10-based
platforms which recently had early-receive de-featured (for stability
reasons) suffer from this.  To resolve this for all devices, when jumbo
frames are enabled set the PM QoS DMA latency request based on the size
of the receive packet buffer less one full frame.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  2 ++
 drivers/net/ethernet/intel/e1000e/netdev.c  | 32 +++++++++++++++--------------
 2 files changed, 19 insertions(+), 15 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 3b997194ac3b..c4587671dc73 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -393,6 +393,8 @@
 #define E1000_PBA_8K  0x0008    /* 8KB */
 #define E1000_PBA_16K 0x0010    /* 16KB */
 
+#define E1000_PBA_RXA_MASK	0xFFFF
+
 #define E1000_PBS_16K E1000_PBA_16K
 
 /* Uncorrectable/correctable ECC Error counts and enable bits */
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index e386e95102f4..46a38a4d8da5 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -3242,18 +3242,23 @@ static void e1000_configure_rx(struct e1000_adapter *adapter)
 		rxcsum &= ~E1000_RXCSUM_TUOFL;
 	ew32(RXCSUM, rxcsum);
 
-	if (adapter->hw.mac.type == e1000_pch2lan) {
-		/* With jumbo frames, excessive C-state transition
-		 * latencies result in dropped transactions.
-		 */
-		if (adapter->netdev->mtu > ETH_DATA_LEN) {
+	/* With jumbo frames, excessive C-state transition latencies result
+	 * in dropped transactions.
+	 */
+	if (adapter->netdev->mtu > ETH_DATA_LEN) {
+		u32 lat =
+		    ((er32(PBA) & E1000_PBA_RXA_MASK) * 1024 -
+		     adapter->max_frame_size) * 8 / 1000;
+
+		if (adapter->flags & FLAG_IS_ICH) {
 			u32 rxdctl = er32(RXDCTL(0));
 			ew32(RXDCTL(0), rxdctl | 0x3);
-			pm_qos_update_request(&adapter->netdev->pm_qos_req, 55);
-		} else {
-			pm_qos_update_request(&adapter->netdev->pm_qos_req,
-					      PM_QOS_DEFAULT_VALUE);
 		}
+
+		pm_qos_update_request(&adapter->netdev->pm_qos_req, lat);
+	} else {
+		pm_qos_update_request(&adapter->netdev->pm_qos_req,
+				      PM_QOS_DEFAULT_VALUE);
 	}
 
 	/* Enable Receives */
@@ -4281,10 +4286,8 @@ static int e1000_open(struct net_device *netdev)
 		e1000_update_mng_vlan(adapter);
 
 	/* DMA latency requirement to workaround jumbo issue */
-	if (adapter->hw.mac.type == e1000_pch2lan)
-		pm_qos_add_request(&adapter->netdev->pm_qos_req,
-				   PM_QOS_CPU_DMA_LATENCY,
-				   PM_QOS_DEFAULT_VALUE);
+	pm_qos_add_request(&adapter->netdev->pm_qos_req, PM_QOS_CPU_DMA_LATENCY,
+			   PM_QOS_DEFAULT_VALUE);
 
 	/* before we allocate an interrupt, we must be ready to handle it.
 	 * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
@@ -4392,8 +4395,7 @@ static int e1000_close(struct net_device *netdev)
 	    !test_bit(__E1000_TESTING, &adapter->state))
 		e1000e_release_hw_control(adapter);
 
-	if (adapter->hw.mac.type == e1000_pch2lan)
-		pm_qos_remove_request(&adapter->netdev->pm_qos_req);
+	pm_qos_remove_request(&adapter->netdev->pm_qos_req);
 
 	pm_runtime_put_sync(&pdev->dev);
 
-- 
cgit v1.2.3


From 41c7d9c96342989cd4a7efe27f768df4528294f7 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 07:25:52 +0000
Subject: e1000e: cleanup: remove unused #define

All references to E1000_ERT_2048 have been removed.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/e1000.h | 3 ---
 1 file changed, 3 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 4ffb62bd0b75..c7d5c5b92ee5 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -78,9 +78,6 @@ struct e1000_info;
 #define E1000_MIN_ITR_USECS		10 /* 100000 irq/sec */
 #define E1000_MAX_ITR_USECS		10000 /* 100    irq/sec */
 
-/* Early Receive defines */
-#define E1000_ERT_2048			0x100
-
 #define E1000_FC_PAUSE_TIME		0x0680 /* 858 usec */
 
 /* How many Tx Descriptors do we need to call netif_wake_queue ? */
-- 
cgit v1.2.3


From a9bb6290392fd9edb7293bb335d0fff1d0b5b376 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 07:26:22 +0000
Subject: e1000e: cleanup hw.h

Remove unnecessary #include, forward prototype of struct e1000_adapter and
an empty comment; fix a comment which mentions "static data for the MAC"
which is not applicable to the following struct; and cleanup some
whitespace issues.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/hw.h | 25 ++++++++++---------------
 1 file changed, 10 insertions(+), 15 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index a10de4d122cc..f32b19af9a72 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -29,12 +29,9 @@
 #ifndef _E1000_HW_H_
 #define _E1000_HW_H_
 
-#include <linux/types.h>
+#include "defines.h"
 
 struct e1000_hw;
-struct e1000_adapter;
-
-#include "defines.h"
 
 enum e1e_registers {
 	E1000_CTRL     = 0x00000, /* Device Control - RW */
@@ -391,13 +388,11 @@ enum e1e_registers {
 #define E1000_DEV_ID_82573L			0x109A
 #define E1000_DEV_ID_82574L			0x10D3
 #define E1000_DEV_ID_82574LA			0x10F6
-#define E1000_DEV_ID_82583V                     0x150C
-
+#define E1000_DEV_ID_82583V			0x150C
 #define E1000_DEV_ID_80003ES2LAN_COPPER_DPT	0x1096
 #define E1000_DEV_ID_80003ES2LAN_SERDES_DPT	0x1098
 #define E1000_DEV_ID_80003ES2LAN_COPPER_SPT	0x10BA
 #define E1000_DEV_ID_80003ES2LAN_SERDES_SPT	0x10BB
-
 #define E1000_DEV_ID_ICH8_82567V_3		0x1501
 #define E1000_DEV_ID_ICH8_IGP_M_AMT		0x1049
 #define E1000_DEV_ID_ICH8_IGP_AMT		0x104A
@@ -432,12 +427,12 @@ enum e1e_registers {
 #define E1000_DEV_ID_PCH_LPTLP_I218_LM		0x155A
 #define E1000_DEV_ID_PCH_LPTLP_I218_V		0x1559
 
-#define E1000_REVISION_4 4
+#define E1000_REVISION_4	4
 
-#define E1000_FUNC_1 1
+#define E1000_FUNC_1		1
 
-#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN0   0
-#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN1   3
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN0	0
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN1	3
 
 enum e1000_mac_type {
 	e1000_82571,
@@ -664,7 +659,7 @@ struct e1000_data_desc {
 		struct {
 			u8 status;     /* Descriptor status */
 			u8 popts;      /* Packet Options */
-			__le16 special;   /* */
+			__le16 special;
 		} fields;
 	} upper;
 };
@@ -760,7 +755,7 @@ struct e1000_host_command_header {
 	u8 checksum;
 };
 
-#define E1000_HI_MAX_DATA_LENGTH     252
+#define E1000_HI_MAX_DATA_LENGTH	252
 struct e1000_host_command_info {
 	struct e1000_host_command_header command_header;
 	u8 command_data[E1000_HI_MAX_DATA_LENGTH];
@@ -775,13 +770,13 @@ struct e1000_host_mng_command_header {
 	u16 command_length;
 };
 
-#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8
+#define E1000_HI_MAX_MNG_DATA_LENGTH	0x6F8
 struct e1000_host_mng_command_info {
 	struct e1000_host_mng_command_header command_header;
 	u8 command_data[E1000_HI_MAX_MNG_DATA_LENGTH];
 };
 
-/* Function pointers and static data for the MAC. */
+/* Function pointers for the MAC. */
 struct e1000_mac_operations {
 	s32  (*id_led_init)(struct e1000_hw *);
 	s32  (*blink_led)(struct e1000_hw *);
-- 
cgit v1.2.3


From 39149d4da6d50de92f9e7f70c743a8b8c20eeac1 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 07:26:53 +0000
Subject: e1000e: cleanup: remove comments which are no longer applicable

Code was removed but the applicable comments were not.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h | 7 -------
 1 file changed, 7 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index c4587671dc73..d29b2fd4c09c 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -261,8 +261,6 @@
 #define E1000_STATUS_PHYRA      0x00000400      /* PHY Reset Asserted */
 #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
 
-/* Constants used to interpret the masked PCI-X bus speed. */
-
 #define HALF_DUPLEX 1
 #define FULL_DUPLEX 2
 
@@ -330,8 +328,6 @@
 #define E1000_TCTL_RTLC   0x01000000    /* Re-transmit on late collision */
 #define E1000_TCTL_MULR   0x10000000    /* Multiple request support */
 
-/* Transmit Arbitration Count */
-
 /* SerDes Control */
 #define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
 
@@ -800,9 +796,6 @@
 #define M88E1000_PSCR_AUTO_X_1000T     0x0040
 /* Auto crossover enabled all speeds */
 #define M88E1000_PSCR_AUTO_X_MODE      0x0060
-/* 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold)
- * 0=Normal 10BASE-T Rx Threshold
- */
 #define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
 
 /* M88E1000 PHY Specific Status Register */
-- 
cgit v1.2.3


From 0cdc63449df6ee5e7840b3e58554d7a41068b542 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 07:27:23 +0000
Subject: e1000e: cleanup defines.h

Remove redundant defines which are defined elsewhere.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h | 21 ---------------------
 1 file changed, 21 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index d29b2fd4c09c..acfe1fadd8de 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -29,25 +29,6 @@
 #ifndef _E1000_DEFINES_H_
 #define _E1000_DEFINES_H_
 
-#define E1000_TXD_POPTS_IXSM 0x01       /* Insert IP checksum */
-#define E1000_TXD_POPTS_TXSM 0x02       /* Insert TCP/UDP checksum */
-#define E1000_TXD_CMD_EOP    0x01000000 /* End of Packet */
-#define E1000_TXD_CMD_IFCS   0x02000000 /* Insert FCS (Ethernet CRC) */
-#define E1000_TXD_CMD_IC     0x04000000 /* Insert Checksum */
-#define E1000_TXD_CMD_RS     0x08000000 /* Report Status */
-#define E1000_TXD_CMD_RPS    0x10000000 /* Report Packet Sent */
-#define E1000_TXD_CMD_DEXT   0x20000000 /* Descriptor extension (0 = legacy) */
-#define E1000_TXD_CMD_VLE    0x40000000 /* Add VLAN tag */
-#define E1000_TXD_CMD_IDE    0x80000000 /* Enable Tidv register */
-#define E1000_TXD_STAT_DD    0x00000001 /* Descriptor Done */
-#define E1000_TXD_STAT_EC    0x00000002 /* Excess Collisions */
-#define E1000_TXD_STAT_LC    0x00000004 /* Late Collisions */
-#define E1000_TXD_STAT_TU    0x00000008 /* Transmit underrun */
-#define E1000_TXD_CMD_TCP    0x01000000 /* TCP packet */
-#define E1000_TXD_CMD_IP     0x02000000 /* IP packet */
-#define E1000_TXD_CMD_TSE    0x04000000 /* TCP Seg enable */
-#define E1000_TXD_STAT_TC    0x00000004 /* Tx Underrun */
-
 /* Number of Transmit and Receive Descriptors must be a multiple of 8 */
 #define REQ_TX_DESCRIPTOR_MULTIPLE  8
 #define REQ_RX_DESCRIPTOR_MULTIPLE  8
@@ -86,7 +67,6 @@
 #define E1000_CTRL_EXT_EIAME          0x01000000
 #define E1000_CTRL_EXT_DRV_LOAD       0x10000000 /* Driver loaded bit for FW */
 #define E1000_CTRL_EXT_IAME           0x08000000 /* Interrupt acknowledge Auto-mask */
-#define E1000_CTRL_EXT_INT_TIMER_CLR  0x20000000 /* Clear Interrupt timers after IMS clear */
 #define E1000_CTRL_EXT_PBA_CLR        0x80000000 /* PBA Clear */
 #define E1000_CTRL_EXT_LSECCK         0x00001000
 #define E1000_CTRL_EXT_PHYPDEN        0x00100000
@@ -546,7 +526,6 @@
 #define E1000_RXCW_SYNCH      0x40000000        /* Receive config synch */
 
 #define E1000_TSYNCTXCTL_VALID		0x00000001 /* Tx timestamp valid */
-#define E1000_TSYNCRXCTL_TYPE_ALL	0x08
 #define E1000_TSYNCTXCTL_ENABLED	0x00000010 /* enable Tx timestamping */
 
 #define E1000_TSYNCRXCTL_VALID		0x00000001 /* Rx timestamp valid */
-- 
cgit v1.2.3


From c063f606fd339676085b55c2ac43d0dd0e10dd7a Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 07:27:53 +0000
Subject: e1000e: cleanup: group OR'ed bit settings with parens

For clarity, wrap OR'ed bit settings with parentheses.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/phy.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index cddfc6b92f75..8dd1da018713 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -3106,8 +3106,9 @@ s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw)
 	msleep(200);
 
 	/* flush the packets in the fifo buffer */
-	ret_val = e1e_wphy(hw, HV_MUX_DATA_CTRL, HV_MUX_DATA_CTRL_GEN_TO_MAC |
-			   HV_MUX_DATA_CTRL_FORCE_SPEED);
+	ret_val = e1e_wphy(hw, HV_MUX_DATA_CTRL,
+			   (HV_MUX_DATA_CTRL_GEN_TO_MAC |
+			    HV_MUX_DATA_CTRL_FORCE_SPEED));
 	if (ret_val)
 		return ret_val;
 
-- 
cgit v1.2.3


From 55c5f55e524cec35b5931df16936118dc6c0837b Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 07:28:24 +0000
Subject: e1000e: cleanup some whitespace and indentation issues

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/80003es2lan.c | 22 ++++++------
 drivers/net/ethernet/intel/e1000e/82571.c       | 13 +++----
 drivers/net/ethernet/intel/e1000e/defines.h     | 47 +++++++++++++------------
 drivers/net/ethernet/intel/e1000e/ich8lan.c     |  4 +--
 drivers/net/ethernet/intel/e1000e/mac.c         |  4 +--
 drivers/net/ethernet/intel/e1000e/netdev.c      |  4 +--
 drivers/net/ethernet/intel/e1000e/param.c       |  3 +-
 7 files changed, 49 insertions(+), 48 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index 3f27546baaa7..765211a289d8 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -1438,18 +1438,18 @@ static const struct e1000_phy_operations es2_phy_ops = {
 	.acquire		= e1000_acquire_phy_80003es2lan,
 	.check_polarity		= e1000_check_polarity_m88,
 	.check_reset_block	= e1000e_check_reset_block_generic,
-	.commit		 	= e1000e_phy_sw_reset,
-	.force_speed_duplex 	= e1000_phy_force_speed_duplex_80003es2lan,
-	.get_cfg_done       	= e1000_get_cfg_done_80003es2lan,
-	.get_cable_length   	= e1000_get_cable_length_80003es2lan,
-	.get_info       	= e1000e_get_phy_info_m88,
-	.read_reg       	= e1000_read_phy_reg_gg82563_80003es2lan,
+	.commit			= e1000e_phy_sw_reset,
+	.force_speed_duplex	= e1000_phy_force_speed_duplex_80003es2lan,
+	.get_cfg_done		= e1000_get_cfg_done_80003es2lan,
+	.get_cable_length	= e1000_get_cable_length_80003es2lan,
+	.get_info		= e1000e_get_phy_info_m88,
+	.read_reg		= e1000_read_phy_reg_gg82563_80003es2lan,
 	.release		= e1000_release_phy_80003es2lan,
-	.reset		  	= e1000e_phy_hw_reset_generic,
-	.set_d0_lplu_state  	= NULL,
-	.set_d3_lplu_state  	= e1000e_set_d3_lplu_state,
-	.write_reg      	= e1000_write_phy_reg_gg82563_80003es2lan,
-	.cfg_on_link_up      	= e1000_cfg_on_link_up_80003es2lan,
+	.reset			= e1000e_phy_hw_reset_generic,
+	.set_d0_lplu_state	= NULL,
+	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
+	.write_reg		= e1000_write_phy_reg_gg82563_80003es2lan,
+	.cfg_on_link_up		= e1000_cfg_on_link_up_80003es2lan,
 };
 
 static const struct e1000_nvm_operations es2_nvm_ops = {
diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index 076938c87a26..db364b69f87e 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -1327,9 +1327,10 @@ static void e1000_clear_vfta_82571(struct e1000_hw *hw)
 			 */
 			vfta_offset = (hw->mng_cookie.vlan_id >>
 				       E1000_VFTA_ENTRY_SHIFT) &
-				      E1000_VFTA_ENTRY_MASK;
-			vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id &
-					       E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
+			    E1000_VFTA_ENTRY_MASK;
+			vfta_bit_in_reg =
+			    1 << (hw->mng_cookie.vlan_id &
+				  E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
 		}
 		break;
 	default:
@@ -1931,7 +1932,7 @@ static const struct e1000_phy_operations e82_phy_ops_igp = {
 	.set_d0_lplu_state	= e1000_set_d0_lplu_state_82571,
 	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
 	.write_reg		= e1000e_write_phy_reg_igp,
-	.cfg_on_link_up      	= NULL,
+	.cfg_on_link_up		= NULL,
 };
 
 static const struct e1000_phy_operations e82_phy_ops_m88 = {
@@ -1949,7 +1950,7 @@ static const struct e1000_phy_operations e82_phy_ops_m88 = {
 	.set_d0_lplu_state	= e1000_set_d0_lplu_state_82571,
 	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
 	.write_reg		= e1000e_write_phy_reg_m88,
-	.cfg_on_link_up      	= NULL,
+	.cfg_on_link_up		= NULL,
 };
 
 static const struct e1000_phy_operations e82_phy_ops_bm = {
@@ -1967,7 +1968,7 @@ static const struct e1000_phy_operations e82_phy_ops_bm = {
 	.set_d0_lplu_state	= e1000_set_d0_lplu_state_82571,
 	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
 	.write_reg		= e1000e_write_phy_reg_bm2,
-	.cfg_on_link_up      	= NULL,
+	.cfg_on_link_up		= NULL,
 };
 
 static const struct e1000_nvm_operations e82571_nvm_ops = {
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index acfe1fadd8de..1257f917af34 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -96,19 +96,19 @@
 
 /* mask to determine if packets should be dropped due to frame errors */
 #define E1000_RXD_ERR_FRAME_ERR_MASK ( \
-    E1000_RXD_ERR_CE  |                \
-    E1000_RXD_ERR_SE  |                \
-    E1000_RXD_ERR_SEQ |                \
-    E1000_RXD_ERR_CXE |                \
-    E1000_RXD_ERR_RXE)
+	E1000_RXD_ERR_CE  |		\
+	E1000_RXD_ERR_SE  |		\
+	E1000_RXD_ERR_SEQ |		\
+	E1000_RXD_ERR_CXE |		\
+	E1000_RXD_ERR_RXE)
 
 /* Same mask, but for extended and packet split descriptors */
 #define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
-    E1000_RXDEXT_STATERR_CE  |            \
-    E1000_RXDEXT_STATERR_SE  |            \
-    E1000_RXDEXT_STATERR_SEQ |            \
-    E1000_RXDEXT_STATERR_CXE |            \
-    E1000_RXDEXT_STATERR_RXE)
+	E1000_RXDEXT_STATERR_CE  |	\
+	E1000_RXDEXT_STATERR_SE  |	\
+	E1000_RXDEXT_STATERR_SEQ |	\
+	E1000_RXDEXT_STATERR_CXE |	\
+	E1000_RXDEXT_STATERR_RXE)
 
 #define E1000_MRQC_RSS_FIELD_MASK              0xFFFF0000
 #define E1000_MRQC_RSS_FIELD_IPV4_TCP          0x00010000
@@ -253,14 +253,15 @@
 #define ADVERTISE_1000_FULL               0x0020
 
 /* 1000/H is not supported, nor spec-compliant. */
-#define E1000_ALL_SPEED_DUPLEX ( ADVERTISE_10_HALF |   ADVERTISE_10_FULL | \
-				ADVERTISE_100_HALF |  ADVERTISE_100_FULL | \
-						     ADVERTISE_1000_FULL)
-#define E1000_ALL_NOT_GIG      ( ADVERTISE_10_HALF |   ADVERTISE_10_FULL | \
-				ADVERTISE_100_HALF |  ADVERTISE_100_FULL)
-#define E1000_ALL_100_SPEED    (ADVERTISE_100_HALF |  ADVERTISE_100_FULL)
-#define E1000_ALL_10_SPEED      (ADVERTISE_10_HALF |   ADVERTISE_10_FULL)
-#define E1000_ALL_HALF_DUPLEX   (ADVERTISE_10_HALF |  ADVERTISE_100_HALF)
+#define E1000_ALL_SPEED_DUPLEX	( \
+	ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
+	ADVERTISE_100_FULL | ADVERTISE_1000_FULL)
+#define E1000_ALL_NOT_GIG	( \
+	ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
+	ADVERTISE_100_FULL)
+#define E1000_ALL_100_SPEED	(ADVERTISE_100_HALF | ADVERTISE_100_FULL)
+#define E1000_ALL_10_SPEED	(ADVERTISE_10_HALF | ADVERTISE_10_FULL)
+#define E1000_ALL_HALF_DUPLEX	(ADVERTISE_10_HALF | ADVERTISE_100_HALF)
 
 #define AUTONEG_ADVERTISE_SPEED_DEFAULT   E1000_ALL_SPEED_DUPLEX
 
@@ -422,11 +423,11 @@
  *   o LSC    = Link Status Change
  */
 #define IMS_ENABLE_MASK ( \
-    E1000_IMS_RXT0   |    \
-    E1000_IMS_TXDW   |    \
-    E1000_IMS_RXDMT0 |    \
-    E1000_IMS_RXSEQ  |    \
-    E1000_IMS_LSC)
+	E1000_IMS_RXT0   |    \
+	E1000_IMS_TXDW   |    \
+	E1000_IMS_RXDMT0 |    \
+	E1000_IMS_RXSEQ  |    \
+	E1000_IMS_LSC)
 
 /* Interrupt Mask Set */
 #define E1000_IMS_TXDW      E1000_ICR_TXDW      /* Transmit desc written back */
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 58547b8abe3d..2ca6f2f502ea 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -4507,7 +4507,7 @@ static const struct e1000_mac_operations ich8_mac_ops = {
 	.reset_hw		= e1000_reset_hw_ich8lan,
 	.init_hw		= e1000_init_hw_ich8lan,
 	.setup_link		= e1000_setup_link_ich8lan,
-	.setup_physical_interface= e1000_setup_copper_link_ich8lan,
+	.setup_physical_interface = e1000_setup_copper_link_ich8lan,
 	/* id_led_init dependent on mac type */
 	.config_collision_dist	= e1000e_config_collision_dist_generic,
 	.rar_set		= e1000e_rar_set_generic,
@@ -4529,7 +4529,7 @@ static const struct e1000_phy_operations ich8_phy_ops = {
 
 static const struct e1000_nvm_operations ich8_nvm_ops = {
 	.acquire		= e1000_acquire_nvm_ich8lan,
-	.read		 	= e1000_read_nvm_ich8lan,
+	.read			= e1000_read_nvm_ich8lan,
 	.release		= e1000_release_nvm_ich8lan,
 	.reload			= e1000e_reload_nvm_generic,
 	.update			= e1000_update_nvm_checksum_ich8lan,
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index 0709f49f0335..5992eefca54e 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -1074,8 +1074,8 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg);
 		if (ret_val)
 			return ret_val;
-		ret_val =
-		    e1e_rphy(hw, PHY_LP_ABILITY, &mii_nway_lp_ability_reg);
+		ret_val = e1e_rphy(hw, PHY_LP_ABILITY,
+				   &mii_nway_lp_ability_reg);
 		if (ret_val)
 			return ret_val;
 
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 46a38a4d8da5..e878dbfb9096 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -6571,8 +6571,8 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	}
 
 	err = pci_request_selected_regions_exclusive(pdev,
-	                                  pci_select_bars(pdev, IORESOURCE_MEM),
-	                                  e1000e_driver_name);
+					  pci_select_bars(pdev, IORESOURCE_MEM),
+					  e1000e_driver_name);
 	if (err)
 		goto err_pci_reg;
 
diff --git a/drivers/net/ethernet/intel/e1000e/param.c b/drivers/net/ethernet/intel/e1000e/param.c
index 19c40d6f53cc..98da75dff936 100644
--- a/drivers/net/ethernet/intel/e1000e/param.c
+++ b/drivers/net/ethernet/intel/e1000e/param.c
@@ -53,8 +53,7 @@ MODULE_PARM_DESC(copybreak,
  */
 #define E1000_PARAM_INIT { [0 ... E1000_MAX_NIC] = OPTION_UNSET }
 #define E1000_PARAM(X, desc)					\
-	static int X[E1000_MAX_NIC+1]		\
-		= E1000_PARAM_INIT;				\
+	static int X[E1000_MAX_NIC+1] = E1000_PARAM_INIT;	\
 	static unsigned int num_##X;				\
 	module_param_array_named(X, X, int, &num_##X, 0);	\
 	MODULE_PARM_DESC(X, desc);
-- 
cgit v1.2.3


From 9e019901816ca4bad83bf4922b791610e6dd529e Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 07:28:54 +0000
Subject: e1000e: update driver version string

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index e878dbfb9096..3bb7b014dd0e 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -56,7 +56,7 @@
 
 #define DRV_EXTRAVERSION "-k"
 
-#define DRV_VERSION "2.1.4" DRV_EXTRAVERSION
+#define DRV_VERSION "2.2.14" DRV_EXTRAVERSION
 char e1000e_driver_name[] = "e1000e";
 const char e1000e_driver_version[] = DRV_VERSION;
 
-- 
cgit v1.2.3


From 8bb628697fb05172f10a0960385b8369be15cb6c Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 16 Jan 2013 08:46:49 +0000
Subject: e1000e: resolve -Wunused-parameter compile warnings

Remove the unused parameter when possible, otherwise use __always_unused
attribute.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ethtool.c | 16 ++++++++------
 drivers/net/ethernet/intel/e1000e/ich8lan.c |  4 ++--
 drivers/net/ethernet/intel/e1000e/mac.c     |  4 ++--
 drivers/net/ethernet/intel/e1000e/netdev.c  | 33 ++++++++++++-----------------
 drivers/net/ethernet/intel/e1000e/phy.c     |  2 +-
 drivers/net/ethernet/intel/e1000e/ptp.c     |  5 +++--
 6 files changed, 31 insertions(+), 33 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 58df18c2efc2..b1447783ff29 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -418,7 +418,7 @@ static void e1000_set_msglevel(struct net_device *netdev, u32 data)
 	adapter->msg_enable = data;
 }
 
-static int e1000_get_regs_len(struct net_device *netdev)
+static int e1000_get_regs_len(struct net_device __always_unused *netdev)
 {
 #define E1000_REGS_LEN 32 /* overestimate */
 	return E1000_REGS_LEN * sizeof(u32);
@@ -934,7 +934,7 @@ static int e1000_eeprom_test(struct e1000_adapter *adapter, u64 *data)
 	return *data;
 }
 
-static irqreturn_t e1000_test_intr(int irq, void *data)
+static irqreturn_t e1000_test_intr(int __always_unused irq, void *data)
 {
 	struct net_device *netdev = (struct net_device *) data;
 	struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -1705,7 +1705,8 @@ static int e1000_link_test(struct e1000_adapter *adapter, u64 *data)
 	return *data;
 }
 
-static int e1000e_get_sset_count(struct net_device *netdev, int sset)
+static int e1000e_get_sset_count(struct net_device __always_unused *netdev,
+				 int sset)
 {
 	switch (sset) {
 	case ETH_SS_TEST:
@@ -1968,7 +1969,7 @@ static int e1000_nway_reset(struct net_device *netdev)
 }
 
 static void e1000_get_ethtool_stats(struct net_device *netdev,
-				    struct ethtool_stats *stats,
+				    struct ethtool_stats __always_unused *stats,
 				    u64 *data)
 {
 	struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -1997,8 +1998,8 @@ static void e1000_get_ethtool_stats(struct net_device *netdev,
 	}
 }
 
-static void e1000_get_strings(struct net_device *netdev, u32 stringset,
-			      u8 *data)
+static void e1000_get_strings(struct net_device __always_unused *netdev,
+			      u32 stringset, u8 *data)
 {
 	u8 *p = data;
 	int i;
@@ -2018,7 +2019,8 @@ static void e1000_get_strings(struct net_device *netdev, u32 stringset,
 }
 
 static int e1000_get_rxnfc(struct net_device *netdev,
-			   struct ethtool_rxnfc *info, u32 *rule_locs)
+			   struct ethtool_rxnfc *info,
+			   u32 __always_unused *rule_locs)
 {
 	info->data = 0;
 
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 2ca6f2f502ea..5ca21f9b3334 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -1082,7 +1082,7 @@ static DEFINE_MUTEX(nvm_mutex);
  *
  *  Acquires the mutex for performing NVM operations.
  **/
-static s32 e1000_acquire_nvm_ich8lan(struct e1000_hw *hw)
+static s32 e1000_acquire_nvm_ich8lan(struct e1000_hw __always_unused *hw)
 {
 	mutex_lock(&nvm_mutex);
 
@@ -1095,7 +1095,7 @@ static s32 e1000_acquire_nvm_ich8lan(struct e1000_hw *hw)
  *
  *  Releases the mutex used while performing NVM operations.
  **/
-static void e1000_release_nvm_ich8lan(struct e1000_hw *hw)
+static void e1000_release_nvm_ich8lan(struct e1000_hw __always_unused *hw)
 {
 	mutex_unlock(&nvm_mutex);
 }
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index 5992eefca54e..7365288f20f7 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -1356,8 +1356,8 @@ s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed,
  *  Sets the speed and duplex to gigabit full duplex (the only possible option)
  *  for fiber/serdes links.
  **/
-s32 e1000e_get_speed_and_duplex_fiber_serdes(struct e1000_hw *hw, u16 *speed,
-					     u16 *duplex)
+s32 e1000e_get_speed_and_duplex_fiber_serdes(struct e1000_hw __always_unused
+					     *hw, u16 *speed, u16 *duplex)
 {
 	*speed = SPEED_1000;
 	*duplex = FULL_DUPLEX;
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 3bb7b014dd0e..eb01a55f60a6 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -1747,7 +1747,7 @@ static void e1000e_downshift_workaround(struct work_struct *work)
  * @irq: interrupt number
  * @data: pointer to a network interface device structure
  **/
-static irqreturn_t e1000_intr_msi(int irq, void *data)
+static irqreturn_t e1000_intr_msi(int __always_unused irq, void *data)
 {
 	struct net_device *netdev = data;
 	struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -1813,7 +1813,7 @@ static irqreturn_t e1000_intr_msi(int irq, void *data)
  * @irq: interrupt number
  * @data: pointer to a network interface device structure
  **/
-static irqreturn_t e1000_intr(int irq, void *data)
+static irqreturn_t e1000_intr(int __always_unused irq, void *data)
 {
 	struct net_device *netdev = data;
 	struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -1888,7 +1888,7 @@ static irqreturn_t e1000_intr(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
-static irqreturn_t e1000_msix_other(int irq, void *data)
+static irqreturn_t e1000_msix_other(int __always_unused irq, void *data)
 {
 	struct net_device *netdev = data;
 	struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -1920,8 +1920,7 @@ no_link_interrupt:
 	return IRQ_HANDLED;
 }
 
-
-static irqreturn_t e1000_intr_msix_tx(int irq, void *data)
+static irqreturn_t e1000_intr_msix_tx(int __always_unused irq, void *data)
 {
 	struct net_device *netdev = data;
 	struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -1939,7 +1938,7 @@ static irqreturn_t e1000_intr_msix_tx(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
-static irqreturn_t e1000_intr_msix_rx(int irq, void *data)
+static irqreturn_t e1000_intr_msix_rx(int __always_unused irq, void *data)
 {
 	struct net_device *netdev = data;
 	struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -2496,9 +2495,7 @@ void e1000e_free_rx_resources(struct e1000_ring *rx_ring)
  *      while increasing bulk throughput.  This functionality is controlled
  *      by the InterruptThrottleRate module parameter.
  **/
-static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
-				     u16 itr_setting, int packets,
-				     int bytes)
+static unsigned int e1000_update_itr(u16 itr_setting, int packets, int bytes)
 {
 	unsigned int retval = itr_setting;
 
@@ -2558,18 +2555,16 @@ static void e1000_set_itr(struct e1000_adapter *adapter)
 		goto set_itr_now;
 	}
 
-	adapter->tx_itr = e1000_update_itr(adapter,
-				    adapter->tx_itr,
-				    adapter->total_tx_packets,
-				    adapter->total_tx_bytes);
+	adapter->tx_itr = e1000_update_itr(adapter->tx_itr,
+					   adapter->total_tx_packets,
+					   adapter->total_tx_bytes);
 	/* conservative mode (itr 3) eliminates the lowest_latency setting */
 	if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency)
 		adapter->tx_itr = low_latency;
 
-	adapter->rx_itr = e1000_update_itr(adapter,
-				    adapter->rx_itr,
-				    adapter->total_rx_packets,
-				    adapter->total_rx_bytes);
+	adapter->rx_itr = e1000_update_itr(adapter->rx_itr,
+					   adapter->total_rx_packets,
+					   adapter->total_rx_bytes);
 	/* conservative mode (itr 3) eliminates the lowest_latency setting */
 	if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency)
 		adapter->rx_itr = low_latency;
@@ -4115,7 +4110,7 @@ static int e1000_sw_init(struct e1000_adapter *adapter)
  * @irq: interrupt number
  * @data: pointer to a network interface device structure
  **/
-static irqreturn_t e1000_intr_msi_test(int irq, void *data)
+static irqreturn_t e1000_intr_msi_test(int __always_unused irq, void *data)
 {
 	struct net_device *netdev = data;
 	struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -6249,7 +6244,7 @@ static void e1000_shutdown(struct pci_dev *pdev)
 
 #ifdef CONFIG_NET_POLL_CONTROLLER
 
-static irqreturn_t e1000_intr_msix(int irq, void *data)
+static irqreturn_t e1000_intr_msix(int __always_unused irq, void *data)
 {
 	struct net_device *netdev = data;
 	struct e1000_adapter *adapter = netdev_priv(netdev);
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 8dd1da018713..6f32811dbcf0 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -2178,7 +2178,7 @@ s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw)
  *  Generic function to wait 10 milli-seconds for configuration to complete
  *  and return success.
  **/
-s32 e1000e_get_cfg_done_generic(struct e1000_hw *hw)
+s32 e1000e_get_cfg_done_generic(struct e1000_hw __always_unused *hw)
 {
 	mdelay(10);
 
diff --git a/drivers/net/ethernet/intel/e1000e/ptp.c b/drivers/net/ethernet/intel/e1000e/ptp.c
index 6b8df6587858..b477fa53ec94 100644
--- a/drivers/net/ethernet/intel/e1000e/ptp.c
+++ b/drivers/net/ethernet/intel/e1000e/ptp.c
@@ -165,8 +165,9 @@ static int e1000e_phc_settime(struct ptp_clock_info *ptp,
  * Enable (or disable) ancillary features of the PHC subsystem.
  * Currently, no ancillary features are supported.
  **/
-static int e1000e_phc_enable(struct ptp_clock_info *ptp,
-			     struct ptp_clock_request *request, int on)
+static int e1000e_phc_enable(struct ptp_clock_info __always_unused *ptp,
+			     struct ptp_clock_request __always_unused *request,
+			     int __always_unused on)
 {
 	return -EOPNOTSUPP;
 }
-- 
cgit v1.2.3


From c2ade1a41d69b8b734dd9947bf7ec25bb2fd2f33 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 16 Jan 2013 08:54:35 +0000
Subject: e1000e: use generic IEEE MII definitions

For standard IEEE MII-compatible transceivers, the kernel has generic
register and bit definitions.  Use those instead of redundant local
defines.

Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000)
when it is not necessary (i.e. when it is bitwise OR'ed with another
value).

Some whitespace issues in the surrounding context of the above changes are
also cleaned up.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/80003es2lan.c |   6 +-
 drivers/net/ethernet/intel/e1000e/82571.c       |   4 +-
 drivers/net/ethernet/intel/e1000e/defines.h     |  60 --------
 drivers/net/ethernet/intel/e1000e/e1000.h       |   1 +
 drivers/net/ethernet/intel/e1000e/ethtool.c     |  24 ++--
 drivers/net/ethernet/intel/e1000e/ich8lan.c     |  10 +-
 drivers/net/ethernet/intel/e1000e/mac.c         |  31 ++--
 drivers/net/ethernet/intel/e1000e/netdev.c      |  27 ++--
 drivers/net/ethernet/intel/e1000e/phy.c         | 179 ++++++++++++------------
 9 files changed, 138 insertions(+), 204 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index 765211a289d8..a00457abce69 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -624,16 +624,16 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
 
 	e_dbg("GG82563 PSCR: %X\n", phy_data);
 
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
 	if (ret_val)
 		return ret_val;
 
 	e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
 
 	/* Reset the phy to commit changes. */
-	phy_data |= MII_CR_RESET;
+	phy_data |= BMCR_RESET;
 
-	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
 	if (ret_val)
 		return ret_val;
 
diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index db364b69f87e..cf86090edd3b 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -447,13 +447,13 @@ static s32 e1000_get_phy_id_82571(struct e1000_hw *hw)
 		break;
 	case e1000_82574:
 	case e1000_82583:
-		ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+		ret_val = e1e_rphy(hw, MII_PHYSID1, &phy_id);
 		if (ret_val)
 			return ret_val;
 
 		phy->id = (u32)(phy_id << 16);
 		udelay(20);
-		ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+		ret_val = e1e_rphy(hw, MII_PHYSID2, &phy_id);
 		if (ret_val)
 			return ret_val;
 
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 1257f917af34..615b900c0152 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -563,66 +563,6 @@
 			   E1000_GCR_TXDSCW_NO_SNOOP      | \
 			   E1000_GCR_TXDSCR_NO_SNOOP)
 
-/* PHY Control Register */
-#define MII_CR_FULL_DUPLEX      0x0100  /* FDX =1, half duplex =0 */
-#define MII_CR_RESTART_AUTO_NEG 0x0200  /* Restart auto negotiation */
-#define MII_CR_POWER_DOWN       0x0800  /* Power down */
-#define MII_CR_AUTO_NEG_EN      0x1000  /* Auto Neg Enable */
-#define MII_CR_LOOPBACK         0x4000  /* 0 = normal, 1 = loopback */
-#define MII_CR_RESET            0x8000  /* 0 = normal, 1 = PHY reset */
-#define MII_CR_SPEED_1000       0x0040
-#define MII_CR_SPEED_100        0x2000
-#define MII_CR_SPEED_10         0x0000
-
-/* PHY Status Register */
-#define MII_SR_LINK_STATUS       0x0004 /* Link Status 1 = link */
-#define MII_SR_AUTONEG_COMPLETE  0x0020 /* Auto Neg Complete */
-
-/* Autoneg Advertisement Register */
-#define NWAY_AR_10T_HD_CAPS      0x0020   /* 10T   Half Duplex Capable */
-#define NWAY_AR_10T_FD_CAPS      0x0040   /* 10T   Full Duplex Capable */
-#define NWAY_AR_100TX_HD_CAPS    0x0080   /* 100TX Half Duplex Capable */
-#define NWAY_AR_100TX_FD_CAPS    0x0100   /* 100TX Full Duplex Capable */
-#define NWAY_AR_PAUSE            0x0400   /* Pause operation desired */
-#define NWAY_AR_ASM_DIR          0x0800   /* Asymmetric Pause Direction bit */
-
-/* Link Partner Ability Register (Base Page) */
-#define NWAY_LPAR_100TX_FD_CAPS  0x0100 /* LP 100TX Full Dplx Capable */
-#define NWAY_LPAR_PAUSE          0x0400 /* LP Pause operation desired */
-#define NWAY_LPAR_ASM_DIR        0x0800 /* LP Asymmetric Pause Direction bit */
-
-/* Autoneg Expansion Register */
-#define NWAY_ER_LP_NWAY_CAPS     0x0001 /* LP has Auto Neg Capability */
-
-/* 1000BASE-T Control Register */
-#define CR_1000T_HD_CAPS         0x0100 /* Advertise 1000T HD capability */
-#define CR_1000T_FD_CAPS         0x0200 /* Advertise 1000T FD capability  */
-					/* 0=DTE device */
-#define CR_1000T_MS_VALUE        0x0800 /* 1=Configure PHY as Master */
-					/* 0=Configure PHY as Slave */
-#define CR_1000T_MS_ENABLE       0x1000 /* 1=Master/Slave manual config value */
-					/* 0=Automatic Master/Slave config */
-
-/* 1000BASE-T Status Register */
-#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
-#define SR_1000T_LOCAL_RX_STATUS  0x2000 /* Local receiver OK */
-
-
-/* PHY 1000 MII Register/Bit Definitions */
-/* PHY Registers defined by IEEE */
-#define PHY_CONTROL      0x00 /* Control Register */
-#define PHY_STATUS       0x01 /* Status Register */
-#define PHY_ID1          0x02 /* Phy Id Reg (word 1) */
-#define PHY_ID2          0x03 /* Phy Id Reg (word 2) */
-#define PHY_AUTONEG_ADV  0x04 /* Autoneg Advertisement */
-#define PHY_LP_ABILITY   0x05 /* Link Partner Ability (Base Page) */
-#define PHY_AUTONEG_EXP  0x06 /* Autoneg Expansion Reg */
-#define PHY_1000T_CTRL   0x09 /* 1000Base-T Control Reg */
-#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
-#define PHY_EXT_STATUS   0x0F /* Extended Status Reg */
-
-#define PHY_CONTROL_LB   0x4000 /* PHY Loopback bit */
-
 /* NVM Control */
 #define E1000_EECD_SK        0x00000001 /* NVM Clock */
 #define E1000_EECD_CS        0x00000002 /* NVM Chip Select */
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index c7d5c5b92ee5..4b0bd9c225cc 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -45,6 +45,7 @@
 #include <linux/net_tstamp.h>
 #include <linux/ptp_clock_kernel.h>
 #include <linux/ptp_classify.h>
+#include <linux/mii.h>
 #include "hw.h"
 
 struct e1000_info;
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index b1447783ff29..c6c3e921686d 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -472,10 +472,10 @@ static void e1000_get_regs(struct net_device *netdev,
 		regs_buff[22] = adapter->phy_stats.receive_errors;
 		regs_buff[23] = regs_buff[13]; /* mdix mode */
 	}
-	regs_buff[21] = 0; /* was idle_errors */
-	e1e_rphy(hw, PHY_1000T_STATUS, &phy_data);
-	regs_buff[24] = (u32)phy_data;  /* phy local receiver status */
-	regs_buff[25] = regs_buff[24];  /* phy remote receiver status */
+	regs_buff[21] = 0;	/* was idle_errors */
+	e1e_rphy(hw, MII_STAT1000, &phy_data);
+	regs_buff[24] = (u32)phy_data;	/* phy local receiver status */
+	regs_buff[25] = regs_buff[24];	/* phy remote receiver status */
 }
 
 static int e1000_get_eeprom_len(struct net_device *netdev)
@@ -1284,7 +1284,7 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 
 	if (hw->phy.type == e1000_phy_ife) {
 		/* force 100, set loopback */
-		e1e_wphy(hw, PHY_CONTROL, 0x6100);
+		e1e_wphy(hw, MII_BMCR, 0x6100);
 
 		/* Now set up the MAC to the same speed/duplex as the PHY. */
 		ctrl_reg = er32(CTRL);
@@ -1307,9 +1307,9 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 		/* Auto-MDI/MDIX Off */
 		e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, 0x0808);
 		/* reset to update Auto-MDI/MDIX */
-		e1e_wphy(hw, PHY_CONTROL, 0x9140);
+		e1e_wphy(hw, MII_BMCR, 0x9140);
 		/* autoneg off */
-		e1e_wphy(hw, PHY_CONTROL, 0x8140);
+		e1e_wphy(hw, MII_BMCR, 0x8140);
 		break;
 	case e1000_phy_gg82563:
 		e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, 0x1CC);
@@ -1363,7 +1363,7 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 	}
 
 	/* force 1000, set loopback */
-	e1e_wphy(hw, PHY_CONTROL, 0x4140);
+	e1e_wphy(hw, MII_BMCR, 0x4140);
 	mdelay(250);
 
 	/* Now set up the MAC to the same speed/duplex as the PHY. */
@@ -1538,10 +1538,10 @@ static void e1000_loopback_cleanup(struct e1000_adapter *adapter)
 		hw->mac.autoneg = 1;
 		if (hw->phy.type == e1000_phy_gg82563)
 			e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, 0x180);
-		e1e_rphy(hw, PHY_CONTROL, &phy_reg);
-		if (phy_reg & MII_CR_LOOPBACK) {
-			phy_reg &= ~MII_CR_LOOPBACK;
-			e1e_wphy(hw, PHY_CONTROL, phy_reg);
+		e1e_rphy(hw, MII_BMCR, &phy_reg);
+		if (phy_reg & BMCR_LOOPBACK) {
+			phy_reg &= ~BMCR_LOOPBACK;
+			e1e_wphy(hw, MII_BMCR, phy_reg);
 			if (hw->phy.ops.commit)
 				hw->phy.ops.commit(hw);
 		}
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 5ca21f9b3334..a019b46f30e2 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -312,12 +312,12 @@ static bool e1000_phy_is_accessible_pchlan(struct e1000_hw *hw)
 	u16 retry_count;
 
 	for (retry_count = 0; retry_count < 2; retry_count++) {
-		ret_val = e1e_rphy_locked(hw, PHY_ID1, &phy_reg);
+		ret_val = e1e_rphy_locked(hw, MII_PHYSID1, &phy_reg);
 		if (ret_val || (phy_reg == 0xFFFF))
 			continue;
 		phy_id = (u32)(phy_reg << 16);
 
-		ret_val = e1e_rphy_locked(hw, PHY_ID2, &phy_reg);
+		ret_val = e1e_rphy_locked(hw, MII_PHYSID2, &phy_reg);
 		if (ret_val || (phy_reg == 0xFFFF)) {
 			phy_id = 0;
 			continue;
@@ -882,8 +882,8 @@ static s32 e1000_set_eee_pchlan(struct e1000_hw *hw)
 			lpi_ctrl |= I82579_LPI_CTRL_1000_ENABLE;
 
 		if (dev_spec->eee_lp_ability & I82579_EEE_100_SUPPORTED) {
-			e1e_rphy_locked(hw, PHY_LP_ABILITY, &data);
-			if (data & NWAY_LPAR_100TX_FD_CAPS)
+			e1e_rphy_locked(hw, MII_LPA, &data);
+			if (data & LPA_100FULL)
 				lpi_ctrl |= I82579_LPI_CTRL_100_ENABLE;
 			else
 				/* EEE is not supported in 100Half, so ignore
@@ -1792,7 +1792,7 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw)
 		 */
 		if (hw->phy.revision < 2) {
 			e1000e_phy_sw_reset(hw);
-			ret_val = e1e_wphy(hw, PHY_CONTROL, 0x3140);
+			ret_val = e1e_wphy(hw, MII_BMCR, 0x3140);
 		}
 	}
 
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index 7365288f20f7..b78e02174601 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -1053,14 +1053,14 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		 * has completed.  We read this twice because this reg has
 		 * some "sticky" (latched) bits.
 		 */
-		ret_val = e1e_rphy(hw, PHY_STATUS, &mii_status_reg);
+		ret_val = e1e_rphy(hw, MII_BMSR, &mii_status_reg);
 		if (ret_val)
 			return ret_val;
-		ret_val = e1e_rphy(hw, PHY_STATUS, &mii_status_reg);
+		ret_val = e1e_rphy(hw, MII_BMSR, &mii_status_reg);
 		if (ret_val)
 			return ret_val;
 
-		if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) {
+		if (!(mii_status_reg & BMSR_ANEGCOMPLETE)) {
 			e_dbg("Copper PHY and Auto Neg has not completed.\n");
 			return ret_val;
 		}
@@ -1071,11 +1071,10 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		 * Page Ability Register (Address 5) to determine how
 		 * flow control was negotiated.
 		 */
-		ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg);
+		ret_val = e1e_rphy(hw, MII_ADVERTISE, &mii_nway_adv_reg);
 		if (ret_val)
 			return ret_val;
-		ret_val = e1e_rphy(hw, PHY_LP_ABILITY,
-				   &mii_nway_lp_ability_reg);
+		ret_val = e1e_rphy(hw, MII_LPA, &mii_nway_lp_ability_reg);
 		if (ret_val)
 			return ret_val;
 
@@ -1112,8 +1111,8 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		 *   1   |   DC    |   1   |   DC    | E1000_fc_full
 		 *
 		 */
-		if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
-		    (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+		if ((mii_nway_adv_reg & ADVERTISE_PAUSE_CAP) &&
+		    (mii_nway_lp_ability_reg & LPA_PAUSE_CAP)) {
 			/* Now we need to check if the user selected Rx ONLY
 			 * of pause frames.  In this case, we had to advertise
 			 * FULL flow control because we could not advertise Rx
@@ -1135,10 +1134,10 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		 *-------|---------|-------|---------|--------------------
 		 *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
 		 */
-		else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
-			 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
-			 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
-			 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+		else if (!(mii_nway_adv_reg & ADVERTISE_PAUSE_CAP) &&
+			 (mii_nway_adv_reg & ADVERTISE_PAUSE_ASYM) &&
+			 (mii_nway_lp_ability_reg & LPA_PAUSE_CAP) &&
+			 (mii_nway_lp_ability_reg & LPA_PAUSE_ASYM)) {
 			hw->fc.current_mode = e1000_fc_tx_pause;
 			e_dbg("Flow Control = Tx PAUSE frames only.\n");
 		}
@@ -1149,10 +1148,10 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		 *-------|---------|-------|---------|--------------------
 		 *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
 		 */
-		else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
-			 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
-			 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
-			 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+		else if ((mii_nway_adv_reg & ADVERTISE_PAUSE_CAP) &&
+			 (mii_nway_adv_reg & ADVERTISE_PAUSE_ASYM) &&
+			 !(mii_nway_lp_ability_reg & LPA_PAUSE_CAP) &&
+			 (mii_nway_lp_ability_reg & LPA_PAUSE_ASYM)) {
 			hw->fc.current_mode = e1000_fc_rx_pause;
 			e_dbg("Flow Control = Rx PAUSE frames only.\n");
 		} else {
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index eb01a55f60a6..e0eb5dddf3ea 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -42,7 +42,6 @@
 #include <linux/slab.h>
 #include <net/checksum.h>
 #include <net/ip6_checksum.h>
-#include <linux/mii.h>
 #include <linux/ethtool.h>
 #include <linux/if_vlan.h>
 #include <linux/cpu.h>
@@ -1117,9 +1116,9 @@ static void e1000_print_hw_hang(struct work_struct *work)
 	adapter->tx_hang_recheck = false;
 	netif_stop_queue(netdev);
 
-	e1e_rphy(hw, PHY_STATUS, &phy_status);
-	e1e_rphy(hw, PHY_1000T_STATUS, &phy_1000t_status);
-	e1e_rphy(hw, PHY_EXT_STATUS, &phy_ext_status);
+	e1e_rphy(hw, MII_BMSR, &phy_status);
+	e1e_rphy(hw, MII_STAT1000, &phy_1000t_status);
+	e1e_rphy(hw, MII_ESTATUS, &phy_ext_status);
 
 	pci_read_config_word(adapter->pdev, PCI_STATUS, &pci_status);
 
@@ -4677,14 +4676,14 @@ static void e1000_phy_read_status(struct e1000_adapter *adapter)
 	    (adapter->hw.phy.media_type == e1000_media_type_copper)) {
 		int ret_val;
 
-		ret_val  = e1e_rphy(hw, PHY_CONTROL, &phy->bmcr);
-		ret_val |= e1e_rphy(hw, PHY_STATUS, &phy->bmsr);
-		ret_val |= e1e_rphy(hw, PHY_AUTONEG_ADV, &phy->advertise);
-		ret_val |= e1e_rphy(hw, PHY_LP_ABILITY, &phy->lpa);
-		ret_val |= e1e_rphy(hw, PHY_AUTONEG_EXP, &phy->expansion);
-		ret_val |= e1e_rphy(hw, PHY_1000T_CTRL, &phy->ctrl1000);
-		ret_val |= e1e_rphy(hw, PHY_1000T_STATUS, &phy->stat1000);
-		ret_val |= e1e_rphy(hw, PHY_EXT_STATUS, &phy->estatus);
+		ret_val = e1e_rphy(hw, MII_BMCR, &phy->bmcr);
+		ret_val |= e1e_rphy(hw, MII_BMSR, &phy->bmsr);
+		ret_val |= e1e_rphy(hw, MII_ADVERTISE, &phy->advertise);
+		ret_val |= e1e_rphy(hw, MII_LPA, &phy->lpa);
+		ret_val |= e1e_rphy(hw, MII_EXPANSION, &phy->expansion);
+		ret_val |= e1e_rphy(hw, MII_CTRL1000, &phy->ctrl1000);
+		ret_val |= e1e_rphy(hw, MII_STAT1000, &phy->stat1000);
+		ret_val |= e1e_rphy(hw, MII_ESTATUS, &phy->estatus);
 		if (ret_val)
 			e_warn("Error reading PHY register\n");
 	} else {
@@ -4856,9 +4855,9 @@ static void e1000_watchdog_task(struct work_struct *work)
 			    (adapter->link_duplex == HALF_DUPLEX)) {
 				u16 autoneg_exp;
 
-				e1e_rphy(hw, PHY_AUTONEG_EXP, &autoneg_exp);
+				e1e_rphy(hw, MII_EXPANSION, &autoneg_exp);
 
-				if (!(autoneg_exp & NWAY_ER_LP_NWAY_CAPS))
+				if (!(autoneg_exp & EXPANSION_NWAY))
 					e_info("Autonegotiated half duplex but link partner cannot autoneg.  Try forcing full duplex if link gets many collisions.\n");
 			}
 
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 6f32811dbcf0..ae656f16c9fd 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -131,13 +131,13 @@ s32 e1000e_get_phy_id(struct e1000_hw *hw)
 		return 0;
 
 	while (retry_count < 2) {
-		ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+		ret_val = e1e_rphy(hw, MII_PHYSID1, &phy_id);
 		if (ret_val)
 			return ret_val;
 
 		phy->id = (u32)(phy_id << 16);
 		udelay(20);
-		ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+		ret_val = e1e_rphy(hw, MII_PHYSID2, &phy_id);
 		if (ret_val)
 			return ret_val;
 
@@ -641,31 +641,31 @@ static s32 e1000_set_master_slave_mode(struct e1000_hw *hw)
 	u16 phy_data;
 
 	/* Resolve Master/Slave mode */
-	ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &phy_data);
+	ret_val = e1e_rphy(hw, MII_CTRL1000, &phy_data);
 	if (ret_val)
 		return ret_val;
 
 	/* load defaults for future use */
-	hw->phy.original_ms_type = (phy_data & CR_1000T_MS_ENABLE) ?
-	    ((phy_data & CR_1000T_MS_VALUE) ?
+	hw->phy.original_ms_type = (phy_data & CTL1000_ENABLE_MASTER) ?
+	    ((phy_data & CTL1000_AS_MASTER) ?
 	     e1000_ms_force_master : e1000_ms_force_slave) : e1000_ms_auto;
 
 	switch (hw->phy.ms_type) {
 	case e1000_ms_force_master:
-		phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
+		phy_data |= (CTL1000_ENABLE_MASTER | CTL1000_AS_MASTER);
 		break;
 	case e1000_ms_force_slave:
-		phy_data |= CR_1000T_MS_ENABLE;
-		phy_data &= ~(CR_1000T_MS_VALUE);
+		phy_data |= CTL1000_ENABLE_MASTER;
+		phy_data &= ~(CTL1000_AS_MASTER);
 		break;
 	case e1000_ms_auto:
-		phy_data &= ~CR_1000T_MS_ENABLE;
+		phy_data &= ~CTL1000_ENABLE_MASTER;
 		/* fall-through */
 	default:
 		break;
 	}
 
-	return e1e_wphy(hw, PHY_1000T_CTRL, phy_data);
+	return e1e_wphy(hw, MII_CTRL1000, phy_data);
 }
 
 /**
@@ -943,12 +943,12 @@ s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw)
 				return ret_val;
 
 			/* Set auto Master/Slave resolution process */
-			ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &data);
+			ret_val = e1e_rphy(hw, MII_CTRL1000, &data);
 			if (ret_val)
 				return ret_val;
 
-			data &= ~CR_1000T_MS_ENABLE;
-			ret_val = e1e_wphy(hw, PHY_1000T_CTRL, data);
+			data &= ~CTL1000_ENABLE_MASTER;
+			ret_val = e1e_wphy(hw, MII_CTRL1000, data);
 			if (ret_val)
 				return ret_val;
 		}
@@ -978,13 +978,13 @@ static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
 	phy->autoneg_advertised &= phy->autoneg_mask;
 
 	/* Read the MII Auto-Neg Advertisement Register (Address 4). */
-	ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
+	ret_val = e1e_rphy(hw, MII_ADVERTISE, &mii_autoneg_adv_reg);
 	if (ret_val)
 		return ret_val;
 
 	if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
 		/* Read the MII 1000Base-T Control Register (Address 9). */
-		ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+		ret_val = e1e_rphy(hw, MII_CTRL1000, &mii_1000t_ctrl_reg);
 		if (ret_val)
 			return ret_val;
 	}
@@ -1000,36 +1000,35 @@ static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
 	 * Advertisement Register (Address 4) and the 1000 mb speed bits in
 	 * the  1000Base-T Control Register (Address 9).
 	 */
-	mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS |
-				 NWAY_AR_100TX_HD_CAPS |
-				 NWAY_AR_10T_FD_CAPS   |
-				 NWAY_AR_10T_HD_CAPS);
-	mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS);
+	mii_autoneg_adv_reg &= ~(ADVERTISE_100FULL |
+				 ADVERTISE_100HALF |
+				 ADVERTISE_10FULL | ADVERTISE_10HALF);
+	mii_1000t_ctrl_reg &= ~(ADVERTISE_1000HALF | ADVERTISE_1000FULL);
 
 	e_dbg("autoneg_advertised %x\n", phy->autoneg_advertised);
 
 	/* Do we want to advertise 10 Mb Half Duplex? */
 	if (phy->autoneg_advertised & ADVERTISE_10_HALF) {
 		e_dbg("Advertise 10mb Half duplex\n");
-		mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+		mii_autoneg_adv_reg |= ADVERTISE_10HALF;
 	}
 
 	/* Do we want to advertise 10 Mb Full Duplex? */
 	if (phy->autoneg_advertised & ADVERTISE_10_FULL) {
 		e_dbg("Advertise 10mb Full duplex\n");
-		mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
+		mii_autoneg_adv_reg |= ADVERTISE_10FULL;
 	}
 
 	/* Do we want to advertise 100 Mb Half Duplex? */
 	if (phy->autoneg_advertised & ADVERTISE_100_HALF) {
 		e_dbg("Advertise 100mb Half duplex\n");
-		mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
+		mii_autoneg_adv_reg |= ADVERTISE_100HALF;
 	}
 
 	/* Do we want to advertise 100 Mb Full Duplex? */
 	if (phy->autoneg_advertised & ADVERTISE_100_FULL) {
 		e_dbg("Advertise 100mb Full duplex\n");
-		mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
+		mii_autoneg_adv_reg |= ADVERTISE_100FULL;
 	}
 
 	/* We do not allow the Phy to advertise 1000 Mb Half Duplex */
@@ -1039,14 +1038,14 @@ static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
 	/* Do we want to advertise 1000 Mb Full Duplex? */
 	if (phy->autoneg_advertised & ADVERTISE_1000_FULL) {
 		e_dbg("Advertise 1000mb Full duplex\n");
-		mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+		mii_1000t_ctrl_reg |= ADVERTISE_1000FULL;
 	}
 
 	/* Check for a software override of the flow control settings, and
 	 * setup the PHY advertisement registers accordingly.  If
 	 * auto-negotiation is enabled, then software will have to set the
 	 * "PAUSE" bits to the correct value in the Auto-Negotiation
-	 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-
+	 * Advertisement Register (MII_ADVERTISE) and re-start auto-
 	 * negotiation.
 	 *
 	 * The possible values of the "fc" parameter are:
@@ -1064,7 +1063,8 @@ static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
 		/* Flow control (Rx & Tx) is completely disabled by a
 		 * software over-ride.
 		 */
-		mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+		mii_autoneg_adv_reg &=
+		    ~(ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP);
 		break;
 	case e1000_fc_rx_pause:
 		/* Rx Flow control is enabled, and Tx Flow control is
@@ -1076,34 +1076,36 @@ static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
 		 * (in e1000e_config_fc_after_link_up) we will disable the
 		 * hw's ability to send PAUSE frames.
 		 */
-		mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+		mii_autoneg_adv_reg |=
+		    (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP);
 		break;
 	case e1000_fc_tx_pause:
 		/* Tx Flow control is enabled, and Rx Flow control is
 		 * disabled, by a software over-ride.
 		 */
-		mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
-		mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
+		mii_autoneg_adv_reg |= ADVERTISE_PAUSE_ASYM;
+		mii_autoneg_adv_reg &= ~ADVERTISE_PAUSE_CAP;
 		break;
 	case e1000_fc_full:
 		/* Flow control (both Rx and Tx) is enabled by a software
 		 * over-ride.
 		 */
-		mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+		mii_autoneg_adv_reg |=
+		    (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP);
 		break;
 	default:
 		e_dbg("Flow control param set incorrectly\n");
 		return -E1000_ERR_CONFIG;
 	}
 
-	ret_val = e1e_wphy(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+	ret_val = e1e_wphy(hw, MII_ADVERTISE, mii_autoneg_adv_reg);
 	if (ret_val)
 		return ret_val;
 
 	e_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
 
 	if (phy->autoneg_mask & ADVERTISE_1000_FULL)
-		ret_val = e1e_wphy(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
+		ret_val = e1e_wphy(hw, MII_CTRL1000, mii_1000t_ctrl_reg);
 
 	return ret_val;
 }
@@ -1145,12 +1147,12 @@ static s32 e1000_copper_link_autoneg(struct e1000_hw *hw)
 	/* Restart auto-negotiation by setting the Auto Neg Enable bit and
 	 * the Auto Neg Restart bit in the PHY control register.
 	 */
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_ctrl);
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_ctrl);
 	if (ret_val)
 		return ret_val;
 
-	phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
-	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_ctrl);
+	phy_ctrl |= (BMCR_ANENABLE | BMCR_ANRESTART);
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_ctrl);
 	if (ret_val)
 		return ret_val;
 
@@ -1237,13 +1239,13 @@ s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw)
 	u16 phy_data;
 	bool link;
 
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
 	if (ret_val)
 		return ret_val;
 
 	e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
 
-	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
 	if (ret_val)
 		return ret_val;
 
@@ -1315,13 +1317,13 @@ s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw)
 
 	e_dbg("M88E1000 PSCR: %X\n", phy_data);
 
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
 	if (ret_val)
 		return ret_val;
 
 	e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
 
-	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
 	if (ret_val)
 		return ret_val;
 
@@ -1408,13 +1410,13 @@ s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw)
 	u16 data;
 	bool link;
 
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &data);
+	ret_val = e1e_rphy(hw, MII_BMCR, &data);
 	if (ret_val)
 		return ret_val;
 
 	e1000e_phy_force_speed_duplex_setup(hw, &data);
 
-	ret_val = e1e_wphy(hw, PHY_CONTROL, data);
+	ret_val = e1e_wphy(hw, MII_BMCR, data);
 	if (ret_val)
 		return ret_val;
 
@@ -1458,13 +1460,13 @@ s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw)
 /**
  *  e1000e_phy_force_speed_duplex_setup - Configure forced PHY speed/duplex
  *  @hw: pointer to the HW structure
- *  @phy_ctrl: pointer to current value of PHY_CONTROL
+ *  @phy_ctrl: pointer to current value of MII_BMCR
  *
  *  Forces speed and duplex on the PHY by doing the following: disable flow
  *  control, force speed/duplex on the MAC, disable auto speed detection,
  *  disable auto-negotiation, configure duplex, configure speed, configure
  *  the collision distance, write configuration to CTRL register.  The
- *  caller must write to the PHY_CONTROL register for these settings to
+ *  caller must write to the MII_BMCR register for these settings to
  *  take affect.
  **/
 void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl)
@@ -1484,29 +1486,28 @@ void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl)
 	ctrl &= ~E1000_CTRL_ASDE;
 
 	/* Disable autoneg on the phy */
-	*phy_ctrl &= ~MII_CR_AUTO_NEG_EN;
+	*phy_ctrl &= ~BMCR_ANENABLE;
 
 	/* Forcing Full or Half Duplex? */
 	if (mac->forced_speed_duplex & E1000_ALL_HALF_DUPLEX) {
 		ctrl &= ~E1000_CTRL_FD;
-		*phy_ctrl &= ~MII_CR_FULL_DUPLEX;
+		*phy_ctrl &= ~BMCR_FULLDPLX;
 		e_dbg("Half Duplex\n");
 	} else {
 		ctrl |= E1000_CTRL_FD;
-		*phy_ctrl |= MII_CR_FULL_DUPLEX;
+		*phy_ctrl |= BMCR_FULLDPLX;
 		e_dbg("Full Duplex\n");
 	}
 
 	/* Forcing 10mb or 100mb? */
 	if (mac->forced_speed_duplex & E1000_ALL_100_SPEED) {
 		ctrl |= E1000_CTRL_SPD_100;
-		*phy_ctrl |= MII_CR_SPEED_100;
-		*phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
+		*phy_ctrl |= BMCR_SPEED100;
+		*phy_ctrl &= ~BMCR_SPEED1000;
 		e_dbg("Forcing 100mb\n");
 	} else {
 		ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
-		*phy_ctrl |= MII_CR_SPEED_10;
-		*phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
+		*phy_ctrl &= ~(BMCR_SPEED1000 | BMCR_SPEED100);
 		e_dbg("Forcing 10mb\n");
 	}
 
@@ -1747,13 +1748,13 @@ static s32 e1000_wait_autoneg(struct e1000_hw *hw)
 
 	/* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */
 	for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) {
-		ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+		ret_val = e1e_rphy(hw, MII_BMSR, &phy_status);
 		if (ret_val)
 			break;
-		ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+		ret_val = e1e_rphy(hw, MII_BMSR, &phy_status);
 		if (ret_val)
 			break;
-		if (phy_status & MII_SR_AUTONEG_COMPLETE)
+		if (phy_status & BMSR_ANEGCOMPLETE)
 			break;
 		msleep(100);
 	}
@@ -1780,21 +1781,21 @@ s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
 	u16 i, phy_status;
 
 	for (i = 0; i < iterations; i++) {
-		/* Some PHYs require the PHY_STATUS register to be read
+		/* Some PHYs require the MII_BMSR register to be read
 		 * twice due to the link bit being sticky.  No harm doing
 		 * it across the board.
 		 */
-		ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+		ret_val = e1e_rphy(hw, MII_BMSR, &phy_status);
 		if (ret_val)
 			/* If the first read fails, another entity may have
 			 * ownership of the resources, wait and try again to
 			 * see if they have relinquished the resources yet.
 			 */
 			udelay(usec_interval);
-		ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+		ret_val = e1e_rphy(hw, MII_BMSR, &phy_status);
 		if (ret_val)
 			break;
-		if (phy_status & MII_SR_LINK_STATUS)
+		if (phy_status & BMSR_LSTATUS)
 			break;
 		if (usec_interval >= 1000)
 			mdelay(usec_interval/1000);
@@ -1968,17 +1969,15 @@ s32 e1000e_get_phy_info_m88(struct e1000_hw *hw)
 		if (ret_val)
 			return ret_val;
 
-		ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &phy_data);
+		ret_val = e1e_rphy(hw, MII_STAT1000, &phy_data);
 		if (ret_val)
 			return ret_val;
 
-		phy->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS)
-				? e1000_1000t_rx_status_ok
-				: e1000_1000t_rx_status_not_ok;
+		phy->local_rx = (phy_data & LPA_1000LOCALRXOK)
+		    ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
 
-		phy->remote_rx = (phy_data & SR_1000T_REMOTE_RX_STATUS)
-				 ? e1000_1000t_rx_status_ok
-				 : e1000_1000t_rx_status_not_ok;
+		phy->remote_rx = (phy_data & LPA_1000REMRXOK)
+		    ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
 	} else {
 		/* Set values to "undefined" */
 		phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
@@ -2032,17 +2031,15 @@ s32 e1000e_get_phy_info_igp(struct e1000_hw *hw)
 		if (ret_val)
 			return ret_val;
 
-		ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &data);
+		ret_val = e1e_rphy(hw, MII_STAT1000, &data);
 		if (ret_val)
 			return ret_val;
 
-		phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
-				? e1000_1000t_rx_status_ok
-				: e1000_1000t_rx_status_not_ok;
+		phy->local_rx = (data & LPA_1000LOCALRXOK)
+		    ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
 
-		phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
-				 ? e1000_1000t_rx_status_ok
-				 : e1000_1000t_rx_status_not_ok;
+		phy->remote_rx = (data & LPA_1000REMRXOK)
+		    ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
 	} else {
 		phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
 		phy->local_rx = e1000_1000t_rx_status_undefined;
@@ -2116,12 +2113,12 @@ s32 e1000e_phy_sw_reset(struct e1000_hw *hw)
 	s32 ret_val;
 	u16 phy_ctrl;
 
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_ctrl);
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_ctrl);
 	if (ret_val)
 		return ret_val;
 
-	phy_ctrl |= MII_CR_RESET;
-	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_ctrl);
+	phy_ctrl |= BMCR_RESET;
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_ctrl);
 	if (ret_val)
 		return ret_val;
 
@@ -2751,9 +2748,9 @@ void e1000_power_up_phy_copper(struct e1000_hw *hw)
 	u16 mii_reg = 0;
 
 	/* The PHY will retain its settings across a power down/up cycle */
-	e1e_rphy(hw, PHY_CONTROL, &mii_reg);
-	mii_reg &= ~MII_CR_POWER_DOWN;
-	e1e_wphy(hw, PHY_CONTROL, mii_reg);
+	e1e_rphy(hw, MII_BMCR, &mii_reg);
+	mii_reg &= ~BMCR_PDOWN;
+	e1e_wphy(hw, MII_BMCR, mii_reg);
 }
 
 /**
@@ -2769,9 +2766,9 @@ void e1000_power_down_phy_copper(struct e1000_hw *hw)
 	u16 mii_reg = 0;
 
 	/* The PHY will retain its settings across a power down/up cycle */
-	e1e_rphy(hw, PHY_CONTROL, &mii_reg);
-	mii_reg |= MII_CR_POWER_DOWN;
-	e1e_wphy(hw, PHY_CONTROL, mii_reg);
+	e1e_rphy(hw, MII_BMCR, &mii_reg);
+	mii_reg |= BMCR_PDOWN;
+	e1e_wphy(hw, MII_BMCR, mii_reg);
 	usleep_range(1000, 2000);
 }
 
@@ -3087,8 +3084,8 @@ s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw)
 		return 0;
 
 	/* Do not apply workaround if in PHY loopback bit 14 set */
-	e1e_rphy(hw, PHY_CONTROL, &data);
-	if (data & PHY_CONTROL_LB)
+	e1e_rphy(hw, MII_BMCR, &data);
+	if (data & BMCR_LOOPBACK)
 		return 0;
 
 	/* check if link is up and at 1Gbps */
@@ -3152,13 +3149,13 @@ s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw)
 	u16 phy_data;
 	bool link;
 
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
 	if (ret_val)
 		return ret_val;
 
 	e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
 
-	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
 	if (ret_val)
 		return ret_val;
 
@@ -3226,17 +3223,15 @@ s32 e1000_get_phy_info_82577(struct e1000_hw *hw)
 		if (ret_val)
 			return ret_val;
 
-		ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &data);
+		ret_val = e1e_rphy(hw, MII_STAT1000, &data);
 		if (ret_val)
 			return ret_val;
 
-		phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
-		                ? e1000_1000t_rx_status_ok
-		                : e1000_1000t_rx_status_not_ok;
+		phy->local_rx = (data & LPA_1000LOCALRXOK)
+		    ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
 
-		phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
-		                 ? e1000_1000t_rx_status_ok
-		                 : e1000_1000t_rx_status_not_ok;
+		phy->remote_rx = (data & LPA_1000REMRXOK)
+		    ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
 	} else {
 		phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
 		phy->local_rx = e1000_1000t_rx_status_undefined;
-- 
cgit v1.2.3


From f25701df2ef171894730534e5b557186d2bacf17 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Tue, 22 Jan 2013 08:44:04 +0000
Subject: e1000e: cosmetic move of #defines and prototypes to the new 82571.h

Move #defines and function prototypes specific to the 8257x family of
devices (82571, 82572, 82573, 82574, 82583) to the new 82571.h header file
(the convention for Intel wired ethernet drivers is to use the name of the
first device in the family for related file and function names).  These
defines and function prototypes can be used by other files in the driver
and moving them to the 8257x-family-specific file makes it clearer to which
devices they are applicable.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/82571.c   | 15 --------
 drivers/net/ethernet/intel/e1000e/82571.h   | 58 +++++++++++++++++++++++++++++
 drivers/net/ethernet/intel/e1000e/defines.h |  2 -
 drivers/net/ethernet/intel/e1000e/e1000.h   |  4 --
 drivers/net/ethernet/intel/e1000e/hw.h      |  5 +--
 drivers/net/ethernet/intel/e1000e/netdev.c  |  1 -
 6 files changed, 60 insertions(+), 25 deletions(-)
 create mode 100644 drivers/net/ethernet/intel/e1000e/82571.h

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index cf86090edd3b..1db7e3df43ea 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -44,21 +44,6 @@
 
 #include "e1000.h"
 
-#define ID_LED_RESERVED_F746 0xF746
-#define ID_LED_DEFAULT_82573 ((ID_LED_DEF1_DEF2 << 12) | \
-			      (ID_LED_OFF1_ON2  <<  8) | \
-			      (ID_LED_DEF1_DEF2 <<  4) | \
-			      (ID_LED_DEF1_DEF2))
-
-#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
-#define AN_RETRY_COUNT          5 /* Autoneg Retry Count value */
-#define E1000_BASE1000T_STATUS          10
-#define E1000_IDLE_ERROR_COUNT_MASK     0xFF
-#define E1000_RECEIVE_ERROR_COUNTER     21
-#define E1000_RECEIVE_ERROR_MAX         0xFFFF
-
-#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */
-
 static s32 e1000_get_phy_id_82571(struct e1000_hw *hw);
 static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw);
 static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw);
diff --git a/drivers/net/ethernet/intel/e1000e/82571.h b/drivers/net/ethernet/intel/e1000e/82571.h
new file mode 100644
index 000000000000..85cb1a3b7cd4
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/82571.h
@@ -0,0 +1,58 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2013 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000E_82571_H_
+#define _E1000E_82571_H_
+
+#define ID_LED_RESERVED_F746	0xF746
+#define ID_LED_DEFAULT_82573	((ID_LED_DEF1_DEF2 << 12) | \
+				 (ID_LED_OFF1_ON2  <<  8) | \
+				 (ID_LED_DEF1_DEF2 <<  4) | \
+				 (ID_LED_DEF1_DEF2))
+
+#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX	0x08000000
+#define AN_RETRY_COUNT		5	/* Autoneg Retry Count value */
+
+/* Intr Throttling - RW */
+#define E1000_EITR_82574(_n)	(0x000E8 + (0x4 * (_n)))
+
+#define E1000_EIAC_82574	0x000DC	/* Ext. Interrupt Auto Clear - RW */
+#define E1000_EIAC_MASK_82574	0x01F00000
+
+/* Manageability Operation Mode mask */
+#define E1000_NVM_INIT_CTRL2_MNGM	0x6000
+
+#define E1000_BASE1000T_STATUS		10
+#define E1000_IDLE_ERROR_COUNT_MASK	0xFF
+#define E1000_RECEIVE_ERROR_COUNTER	21
+#define E1000_RECEIVE_ERROR_MAX		0xFFFF
+bool e1000_check_phy_82574(struct e1000_hw *hw);
+bool e1000e_get_laa_state_82571(struct e1000_hw *hw);
+void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state);
+
+#endif
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 615b900c0152..b425544144ec 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -606,8 +606,6 @@
 #define NVM_ALT_MAC_ADDR_PTR       0x0037
 #define NVM_CHECKSUM_REG           0x003F
 
-#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */
-
 #define E1000_NVM_CFG_DONE_PORT_0  0x40000 /* MNG config cycle done */
 #define E1000_NVM_CFG_DONE_PORT_1  0x80000 /* ...for second port */
 
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 4b0bd9c225cc..12c5d4043505 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -579,9 +579,6 @@ extern s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
 
 extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
 
-extern bool e1000e_get_laa_state_82571(struct e1000_hw *hw);
-extern void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state);
-
 extern void e1000e_write_protect_nvm_ich8lan(struct e1000_hw *hw);
 extern void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
 						 bool state);
@@ -703,7 +700,6 @@ extern s32 e1000_get_phy_info_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_ife(struct e1000_hw *hw);
 extern s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_igp(struct e1000_hw *hw);
-extern bool e1000_check_phy_82574(struct e1000_hw *hw);
 extern s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
 extern void e1000e_ptp_init(struct e1000_adapter *adapter);
 extern void e1000e_ptp_remove(struct e1000_adapter *adapter);
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index f32b19af9a72..6f94437d8c0e 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -54,12 +54,9 @@ enum e1e_registers {
 	E1000_ICS      = 0x000C8, /* Interrupt Cause Set - WO */
 	E1000_IMS      = 0x000D0, /* Interrupt Mask Set - RW */
 	E1000_IMC      = 0x000D8, /* Interrupt Mask Clear - WO */
-	E1000_EIAC_82574 = 0x000DC, /* Ext. Interrupt Auto Clear - RW */
 	E1000_IAM      = 0x000E0, /* Interrupt Acknowledge Auto Mask */
 	E1000_IVAR     = 0x000E4, /* Interrupt Vector Allocation - RW */
 	E1000_FEXTNVM7  = 0x000E4, /* Future Extended NVM 7 - RW */
-	E1000_EITR_82574_BASE = 0x000E8, /* Interrupt Throttling - RW */
-#define E1000_EITR_82574(_n) (E1000_EITR_82574_BASE + (_n << 2))
 	E1000_LPIC     = 0x000FC, /* Low Power Idle Control - RW */
 	E1000_RCTL     = 0x00100, /* Rx Control - RW */
 	E1000_FCTTV    = 0x00170, /* Flow Control Transmit Timer Value - RW */
@@ -1005,4 +1002,6 @@ struct e1000_hw {
 	} dev_spec;
 };
 
+#include "82571.h"
+
 #endif
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index e0eb5dddf3ea..6fcf9e8008c0 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -2024,7 +2024,6 @@ static void e1000_configure_msix(struct e1000_adapter *adapter)
 	ctrl_ext |= E1000_CTRL_EXT_PBA_CLR;
 
 	/* Auto-Mask Other interrupts upon ICR read */
-#define E1000_EIAC_MASK_82574   0x01F00000
 	ew32(IAM, ~E1000_EIAC_MASK_82574 | E1000_IMS_OTHER);
 	ctrl_ext |= E1000_CTRL_EXT_EIAME;
 	ew32(CTRL_EXT, ctrl_ext);
-- 
cgit v1.2.3


From 21b5a6f8ff3cbcd7623187628320a4e7125120fb Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Tue, 22 Jan 2013 08:44:09 +0000
Subject: e1000e: cosmetic move of #defines to the new 80003es2lan.h

Move #defines specific to the ESB2/82563 family of devices to the new
80003es2lan.h header file.  These defines can be used by other files in the
driver and moving them to the 80003es2lan-family-specific file makes it
clearer to which devices they are applicable.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/80003es2lan.c | 63 ----------------
 drivers/net/ethernet/intel/e1000e/80003es2lan.h | 95 +++++++++++++++++++++++++
 drivers/net/ethernet/intel/e1000e/hw.h          |  1 +
 3 files changed, 96 insertions(+), 63 deletions(-)
 create mode 100644 drivers/net/ethernet/intel/e1000e/80003es2lan.h

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index a00457abce69..e0991388664c 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -32,69 +32,6 @@
 
 #include "e1000.h"
 
-#define E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL	 0x00
-#define E1000_KMRNCTRLSTA_OFFSET_INB_CTRL	 0x02
-#define E1000_KMRNCTRLSTA_OFFSET_HD_CTRL	 0x10
-#define E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE	 0x1F
-
-#define E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS	 0x0008
-#define E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS	 0x0800
-#define E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING	 0x0010
-
-#define E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT 0x0004
-#define E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT	 0x0000
-#define E1000_KMRNCTRLSTA_OPMODE_E_IDLE		 0x2000
-
-#define E1000_KMRNCTRLSTA_OPMODE_MASK		 0x000C
-#define E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO	 0x0004
-
-#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */
-#define DEFAULT_TCTL_EXT_GCEX_80003ES2LAN	 0x00010000
-
-#define DEFAULT_TIPG_IPGT_1000_80003ES2LAN	 0x8
-#define DEFAULT_TIPG_IPGT_10_100_80003ES2LAN	 0x9
-
-/* GG82563 PHY Specific Status Register (Page 0, Register 16 */
-#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE	 0x0002 /* 1=Reversal Disab. */
-#define GG82563_PSCR_CROSSOVER_MODE_MASK	 0x0060
-#define GG82563_PSCR_CROSSOVER_MODE_MDI		 0x0000 /* 00=Manual MDI */
-#define GG82563_PSCR_CROSSOVER_MODE_MDIX	 0x0020 /* 01=Manual MDIX */
-#define GG82563_PSCR_CROSSOVER_MODE_AUTO	 0x0060 /* 11=Auto crossover */
-
-/* PHY Specific Control Register 2 (Page 0, Register 26) */
-#define GG82563_PSCR2_REVERSE_AUTO_NEG		 0x2000
-						/* 1=Reverse Auto-Negotiation */
-
-/* MAC Specific Control Register (Page 2, Register 21) */
-/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */
-#define GG82563_MSCR_TX_CLK_MASK		 0x0007
-#define GG82563_MSCR_TX_CLK_10MBPS_2_5		 0x0004
-#define GG82563_MSCR_TX_CLK_100MBPS_25		 0x0005
-#define GG82563_MSCR_TX_CLK_1000MBPS_25		 0x0007
-
-#define GG82563_MSCR_ASSERT_CRS_ON_TX		 0x0010 /* 1=Assert */
-
-/* DSP Distance Register (Page 5, Register 26) */
-#define GG82563_DSPD_CABLE_LENGTH		 0x0007 /* 0 = <50M
-							   1 = 50-80M
-							   2 = 80-110M
-							   3 = 110-140M
-							   4 = >140M
-							*/
-
-/* Kumeran Mode Control Register (Page 193, Register 16) */
-#define GG82563_KMCR_PASS_FALSE_CARRIER		 0x0800
-
-/* Max number of times Kumeran read/write should be validated */
-#define GG82563_MAX_KMRN_RETRY  0x5
-
-/* Power Management Control Register (Page 193, Register 20) */
-#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE	 0x0001
-					   /* 1=Enable SERDES Electrical Idle */
-
-/* In-Band Control Register (Page 194, Register 18) */
-#define GG82563_ICR_DIS_PADDING			 0x0010 /* Disable Padding */
-
 /* A table for the GG82563 cable length where the range is defined
  * with a lower bound at "index" and the upper bound at
  * "index + 5".
diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.h b/drivers/net/ethernet/intel/e1000e/80003es2lan.h
new file mode 100644
index 000000000000..90d363b2d280
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.h
@@ -0,0 +1,95 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2013 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000E_80003ES2LAN_H_
+#define _E1000E_80003ES2LAN_H_
+
+#define E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL	0x00
+#define E1000_KMRNCTRLSTA_OFFSET_INB_CTRL	0x02
+#define E1000_KMRNCTRLSTA_OFFSET_HD_CTRL	0x10
+#define E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE	0x1F
+
+#define E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS	0x0008
+#define E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS	0x0800
+#define E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING	0x0010
+
+#define E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT 0x0004
+#define E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT	0x0000
+#define E1000_KMRNCTRLSTA_OPMODE_E_IDLE		0x2000
+
+#define E1000_KMRNCTRLSTA_OPMODE_MASK		0x000C
+#define E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO	0x0004
+
+#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00	/* Gig Carry Extend Padding */
+#define DEFAULT_TCTL_EXT_GCEX_80003ES2LAN	0x00010000
+
+#define DEFAULT_TIPG_IPGT_1000_80003ES2LAN	0x8
+#define DEFAULT_TIPG_IPGT_10_100_80003ES2LAN	0x9
+
+/* GG82563 PHY Specific Status Register (Page 0, Register 16 */
+#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE	0x0002	/* 1=Reversal Dis */
+#define GG82563_PSCR_CROSSOVER_MODE_MASK	0x0060
+#define GG82563_PSCR_CROSSOVER_MODE_MDI		0x0000	/* 00=Manual MDI */
+#define GG82563_PSCR_CROSSOVER_MODE_MDIX	0x0020	/* 01=Manual MDIX */
+#define GG82563_PSCR_CROSSOVER_MODE_AUTO	0x0060	/* 11=Auto crossover */
+
+/* PHY Specific Control Register 2 (Page 0, Register 26) */
+#define GG82563_PSCR2_REVERSE_AUTO_NEG		0x2000	/* 1=Reverse Auto-Neg */
+
+/* MAC Specific Control Register (Page 2, Register 21) */
+/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */
+#define GG82563_MSCR_TX_CLK_MASK		0x0007
+#define GG82563_MSCR_TX_CLK_10MBPS_2_5		0x0004
+#define GG82563_MSCR_TX_CLK_100MBPS_25		0x0005
+#define GG82563_MSCR_TX_CLK_1000MBPS_25		0x0007
+
+#define GG82563_MSCR_ASSERT_CRS_ON_TX		0x0010	/* 1=Assert */
+
+/* DSP Distance Register (Page 5, Register 26)
+ * 0 = <50M
+ * 1 = 50-80M
+ * 2 = 80-100M
+ * 3 = 110-140M
+ * 4 = >140M
+ */
+#define GG82563_DSPD_CABLE_LENGTH		0x0007
+
+/* Kumeran Mode Control Register (Page 193, Register 16) */
+#define GG82563_KMCR_PASS_FALSE_CARRIER		0x0800
+
+/* Max number of times Kumeran read/write should be validated */
+#define GG82563_MAX_KMRN_RETRY			0x5
+
+/* Power Management Control Register (Page 193, Register 20) */
+/* 1=Enable SERDES Electrical Idle */
+#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE	0x0001
+
+/* In-Band Control Register (Page 194, Register 18) */
+#define GG82563_ICR_DIS_PADDING			0x0010	/* Disable Padding */
+
+#endif
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 6f94437d8c0e..8a145f468721 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -1003,5 +1003,6 @@ struct e1000_hw {
 };
 
 #include "82571.h"
+#include "80003es2lan.h"
 
 #endif
-- 
cgit v1.2.3


From 1b41db37f40dc682ee5d6fb47b3af545c3eabd1f Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Tue, 22 Jan 2013 08:44:14 +0000
Subject: e1000e: cosmetic move of #defines and prototypes to the new ich8lan.h

Move #defines and function prototypes specific to the ICH/PCH family of
devices (ICH8/82562, ICH8/82566, ICH8/82567, ICH9/82562, ICH9/82566,
ICH9/82567, ICH10/82567, 82577, 82578, 82579, I217, I218) to the new
ich8lan.h header file (the convention for Intel wired ethernet drivers is
to use the name of the first device in the family for related file and
function names).  These defines and function prototypes can be used by
other files in the driver and moving them to the ICH/PCH-family-specific
file makes it clearer to which devices they are applicable.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  36 ----
 drivers/net/ethernet/intel/e1000e/e1000.h   |  53 ------
 drivers/net/ethernet/intel/e1000e/hw.h      |  13 +-
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 126 -------------
 drivers/net/ethernet/intel/e1000e/ich8lan.h | 268 ++++++++++++++++++++++++++++
 drivers/net/ethernet/intel/e1000e/phy.c     |   4 -
 6 files changed, 270 insertions(+), 230 deletions(-)
 create mode 100644 drivers/net/ethernet/intel/e1000e/ich8lan.h

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index b425544144ec..fc3a4fe1ac71 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -749,38 +749,6 @@
 /* BME1000 PHY Specific Control Register */
 #define BME1000_PSCR_ENABLE_DOWNSHIFT   0x0800 /* 1 = enable downshift */
 
-/* PHY Low Power Idle Control */
-#define I82579_LPI_CTRL				PHY_REG(772, 20)
-#define I82579_LPI_CTRL_100_ENABLE		0x2000
-#define I82579_LPI_CTRL_1000_ENABLE		0x4000
-#define I82579_LPI_CTRL_ENABLE_MASK		0x6000
-#define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
-
-/* Extended Management Interface (EMI) Registers */
-#define I82579_EMI_ADDR		0x10
-#define I82579_EMI_DATA		0x11
-#define I82579_LPI_UPDATE_TIMER	0x4805	/* in 40ns units + 40 ns base value */
-#define I82579_MSE_THRESHOLD	0x084F	/* 82579 Mean Square Error Threshold */
-#define I82577_MSE_THRESHOLD	0x0887	/* 82577 Mean Square Error Threshold */
-#define I82579_MSE_LINK_DOWN	0x2411	/* MSE count before dropping link */
-#define I82579_EEE_PCS_STATUS	0x182D	/* IEEE MMD Register 3.1 >> 8 */
-#define I82579_EEE_CAPABILITY	0x0410	/* IEEE MMD Register 3.20 */
-#define I82579_EEE_ADVERTISEMENT	0x040E	/* IEEE MMD Register 7.60 */
-#define I82579_EEE_LP_ABILITY		0x040F	/* IEEE MMD Register 7.61 */
-#define I82579_EEE_100_SUPPORTED	(1 << 1) /* 100BaseTx EEE supported */
-#define I82579_EEE_1000_SUPPORTED	(1 << 2) /* 1000BaseTx EEE supported */
-#define I217_EEE_PCS_STATUS	0x9401	/* IEEE MMD Register 3.1 */
-#define I217_EEE_CAPABILITY	0x8000	/* IEEE MMD Register 3.20 */
-#define I217_EEE_ADVERTISEMENT	0x8001	/* IEEE MMD Register 7.60 */
-#define I217_EEE_LP_ABILITY	0x8002	/* IEEE MMD Register 7.61 */
-
-#define E1000_EEE_RX_LPI_RCVD	0x0400	/* Tx LP idle received */
-#define E1000_EEE_TX_LPI_RCVD	0x0800	/* Rx LP idle received */
-
-#define PHY_PAGE_SHIFT 5
-#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
-                           ((reg) & MAX_PHY_REG_ADDRESS))
-
 /* Bits...
  * 15-5: page
  * 4-0: register offset
@@ -827,8 +795,4 @@
 /* SerDes Control */
 #define E1000_GEN_POLL_TIMEOUT          640
 
-/* FW Semaphore */
-#define E1000_FWSM_WLOCK_MAC_MASK	0x0380
-#define E1000_FWSM_WLOCK_MAC_SHIFT	7
-
 #endif /* _E1000_DEFINES_H_ */
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 12c5d4043505..7a383cd715d6 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -104,44 +104,6 @@ struct e1000_info;
 	 (((page) & 0xFFFF) << PHY_PAGE_SHIFT) |\
 	 (((reg) & ~MAX_PHY_REG_ADDRESS) << (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)))
 
-/* PHY Wakeup Registers and defines */
-#define BM_PORT_GEN_CFG PHY_REG(BM_PORT_CTRL_PAGE, 17)
-#define BM_RCTL         PHY_REG(BM_WUC_PAGE, 0)
-#define BM_WUC          PHY_REG(BM_WUC_PAGE, 1)
-#define BM_WUFC         PHY_REG(BM_WUC_PAGE, 2)
-#define BM_WUS          PHY_REG(BM_WUC_PAGE, 3)
-#define BM_RAR_L(_i)    (BM_PHY_REG(BM_WUC_PAGE, 16 + ((_i) << 2)))
-#define BM_RAR_M(_i)    (BM_PHY_REG(BM_WUC_PAGE, 17 + ((_i) << 2)))
-#define BM_RAR_H(_i)    (BM_PHY_REG(BM_WUC_PAGE, 18 + ((_i) << 2)))
-#define BM_RAR_CTRL(_i) (BM_PHY_REG(BM_WUC_PAGE, 19 + ((_i) << 2)))
-#define BM_MTA(_i)      (BM_PHY_REG(BM_WUC_PAGE, 128 + ((_i) << 1)))
-
-#define BM_RCTL_UPE           0x0001          /* Unicast Promiscuous Mode */
-#define BM_RCTL_MPE           0x0002          /* Multicast Promiscuous Mode */
-#define BM_RCTL_MO_SHIFT      3               /* Multicast Offset Shift */
-#define BM_RCTL_MO_MASK       (3 << 3)        /* Multicast Offset Mask */
-#define BM_RCTL_BAM           0x0020          /* Broadcast Accept Mode */
-#define BM_RCTL_PMCF          0x0040          /* Pass MAC Control Frames */
-#define BM_RCTL_RFCE          0x0080          /* Rx Flow Control Enable */
-
-#define HV_STATS_PAGE	778
-#define HV_SCC_UPPER	PHY_REG(HV_STATS_PAGE, 16) /* Single Collision Count */
-#define HV_SCC_LOWER	PHY_REG(HV_STATS_PAGE, 17)
-#define HV_ECOL_UPPER	PHY_REG(HV_STATS_PAGE, 18) /* Excessive Coll. Count */
-#define HV_ECOL_LOWER	PHY_REG(HV_STATS_PAGE, 19)
-#define HV_MCC_UPPER	PHY_REG(HV_STATS_PAGE, 20) /* Multiple Coll. Count */
-#define HV_MCC_LOWER	PHY_REG(HV_STATS_PAGE, 21)
-#define HV_LATECOL_UPPER PHY_REG(HV_STATS_PAGE, 23) /* Late Collision Count */
-#define HV_LATECOL_LOWER PHY_REG(HV_STATS_PAGE, 24)
-#define HV_COLC_UPPER	PHY_REG(HV_STATS_PAGE, 25) /* Collision Count */
-#define HV_COLC_LOWER	PHY_REG(HV_STATS_PAGE, 26)
-#define HV_DC_UPPER	PHY_REG(HV_STATS_PAGE, 27) /* Defer Count */
-#define HV_DC_LOWER	PHY_REG(HV_STATS_PAGE, 28)
-#define HV_TNCRS_UPPER	PHY_REG(HV_STATS_PAGE, 29) /* Transmit with no CRS */
-#define HV_TNCRS_LOWER	PHY_REG(HV_STATS_PAGE, 30)
-
-#define E1000_FCRTV_PCH     0x05F40 /* PCH Flow Control Refresh Timer Value */
-
 /* BM PHY Copper Specific Status */
 #define BM_CS_STATUS                      17
 #define BM_CS_STATUS_LINK_UP              0x0400
@@ -156,9 +118,6 @@ struct e1000_info;
 #define HV_M_STATUS_SPEED_1000            0x0200
 #define HV_M_STATUS_LINK_UP               0x0040
 
-#define E1000_ICH_FWSM_PCIM2PCI		0x01000000 /* ME PCIm-to-PCI active */
-#define E1000_ICH_FWSM_PCIM2PCI_COUNT	2000
-
 /* Time to wait before putting the device into D3 if there's no link (in ms). */
 #define LINK_TIMEOUT		100
 
@@ -579,17 +538,6 @@ extern s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
 
 extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
 
-extern void e1000e_write_protect_nvm_ich8lan(struct e1000_hw *hw);
-extern void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
-						 bool state);
-extern void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
-extern void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw);
-extern void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw);
-extern void e1000_resume_workarounds_pchlan(struct e1000_hw *hw);
-extern s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
-extern s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable);
-extern void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw);
-
 extern s32 e1000e_check_for_copper_link(struct e1000_hw *hw);
 extern s32 e1000e_check_for_fiber_link(struct e1000_hw *hw);
 extern s32 e1000e_check_for_serdes_link(struct e1000_hw *hw);
@@ -700,7 +648,6 @@ extern s32 e1000_get_phy_info_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_ife(struct e1000_hw *hw);
 extern s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_igp(struct e1000_hw *hw);
-extern s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
 extern void e1000e_ptp_init(struct e1000_adapter *adapter);
 extern void e1000e_ptp_remove(struct e1000_adapter *adapter);
 
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 8a145f468721..21a9cc36e467 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -200,10 +200,6 @@ enum e1e_registers {
 #define E1000_RA        (E1000_RAL(0))
 	E1000_RAH_BASE = 0x05404, /* Receive Address High - RW */
 #define E1000_RAH(_n)   (E1000_RAH_BASE + ((_n) * 8))
-	E1000_SHRAL_PCH_LPT_BASE = 0x05408,
-#define E1000_SHRAL_PCH_LPT(_n)   (E1000_SHRAL_PCH_LPT_BASE + ((_n) * 8))
-	E1000_SHRAH_PCH_LTP_BASE = 0x0540C,
-#define E1000_SHRAH_PCH_LPT(_n)   (E1000_SHRAH_PCH_LTP_BASE + ((_n) * 8))
 	E1000_SHRAL_BASE = 0x05438, /* Shared Receive Address Low - RW */
 #define E1000_SHRAL(_n)   (E1000_SHRAL_BASE + ((_n) * 8))
 	E1000_SHRAH_BASE = 0x0543C, /* Shared Receive Address High - RW */
@@ -215,6 +211,7 @@ enum e1e_registers {
 	E1000_MRQC     = 0x05818, /* Multiple Receive Control - RW */
 	E1000_MANC     = 0x05820, /* Management Control - RW */
 	E1000_FFLT     = 0x05F00, /* Flexible Filter Length Table - RW Array */
+	E1000_CRC_OFFSET = 0x05F50, /* CRC Offset register */
 	E1000_HOST_IF  = 0x08800, /* Host Interface */
 
 	E1000_KMRNCTRLSTA = 0x00034, /* MAC-PHY interface - RW */
@@ -233,9 +230,6 @@ enum e1e_registers {
 	E1000_RSSRK_BASE = 0x05C80, /* RSS Random Key - RW */
 #define E1000_RSSRK(_n)	(E1000_RSSRK_BASE + ((_n) * 4))
 	E1000_FFLT_DBG  = 0x05F04, /* Debug Register */
-	E1000_PCH_RAICC_BASE = 0x05F50, /* Receive Address Initial CRC */
-#define E1000_PCH_RAICC(_n)	(E1000_PCH_RAICC_BASE + ((_n) * 4))
-#define E1000_CRC_OFFSET	E1000_PCH_RAICC_BASE
 	E1000_HICR      = 0x08F00, /* Host Interface Control */
 	E1000_SYSTIML   = 0x0B600, /* System time register Low - RO */
 	E1000_SYSTIMH   = 0x0B604, /* System time register High - RO */
@@ -272,10 +266,6 @@ enum e1e_registers {
 #define BM_WUC_HOST_WU_BIT		(1 << 4)
 #define BM_WUC_ME_WU_BIT		(1 << 5)
 
-#define BM_WUC	PHY_REG(BM_WUC_PAGE, 1)
-#define BM_WUFC PHY_REG(BM_WUC_PAGE, 2)
-#define BM_WUS	PHY_REG(BM_WUC_PAGE, 3)
-
 #define IGP01E1000_PHY_PCS_INIT_REG	0x00B4
 #define IGP01E1000_PHY_POLARITY_MASK	0x0078
 
@@ -1004,5 +994,6 @@ struct e1000_hw {
 
 #include "82571.h"
 #include "80003es2lan.h"
+#include "ich8lan.h"
 
 #endif
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index a019b46f30e2..1e838b235e8a 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -57,132 +57,6 @@
 
 #include "e1000.h"
 
-#define ICH_FLASH_GFPREG		0x0000
-#define ICH_FLASH_HSFSTS		0x0004
-#define ICH_FLASH_HSFCTL		0x0006
-#define ICH_FLASH_FADDR			0x0008
-#define ICH_FLASH_FDATA0		0x0010
-#define ICH_FLASH_PR0			0x0074
-
-#define ICH_FLASH_READ_COMMAND_TIMEOUT	500
-#define ICH_FLASH_WRITE_COMMAND_TIMEOUT	500
-#define ICH_FLASH_ERASE_COMMAND_TIMEOUT	3000000
-#define ICH_FLASH_LINEAR_ADDR_MASK	0x00FFFFFF
-#define ICH_FLASH_CYCLE_REPEAT_COUNT	10
-
-#define ICH_CYCLE_READ			0
-#define ICH_CYCLE_WRITE			2
-#define ICH_CYCLE_ERASE			3
-
-#define FLASH_GFPREG_BASE_MASK		0x1FFF
-#define FLASH_SECTOR_ADDR_SHIFT		12
-
-#define ICH_FLASH_SEG_SIZE_256		256
-#define ICH_FLASH_SEG_SIZE_4K		4096
-#define ICH_FLASH_SEG_SIZE_8K		8192
-#define ICH_FLASH_SEG_SIZE_64K		65536
-
-
-#define E1000_ICH_FWSM_RSPCIPHY	0x00000040 /* Reset PHY on PCI Reset */
-/* FW established a valid mode */
-#define E1000_ICH_FWSM_FW_VALID		0x00008000
-
-#define E1000_ICH_MNG_IAMT_MODE		0x2
-
-#define ID_LED_DEFAULT_ICH8LAN  ((ID_LED_DEF1_DEF2 << 12) | \
-				 (ID_LED_DEF1_OFF2 <<  8) | \
-				 (ID_LED_DEF1_ON2  <<  4) | \
-				 (ID_LED_DEF1_DEF2))
-
-#define E1000_ICH_NVM_SIG_WORD		0x13
-#define E1000_ICH_NVM_SIG_MASK		0xC000
-#define E1000_ICH_NVM_VALID_SIG_MASK    0xC0
-#define E1000_ICH_NVM_SIG_VALUE         0x80
-
-#define E1000_ICH8_LAN_INIT_TIMEOUT	1500
-
-#define E1000_FEXTNVM_SW_CONFIG		1
-#define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* Bit redefined for ICH8M :/ */
-
-#define E1000_FEXTNVM3_PHY_CFG_COUNTER_MASK    0x0C000000
-#define E1000_FEXTNVM3_PHY_CFG_COUNTER_50MSEC  0x08000000
-
-#define E1000_FEXTNVM4_BEACON_DURATION_MASK    0x7
-#define E1000_FEXTNVM4_BEACON_DURATION_8USEC   0x7
-#define E1000_FEXTNVM4_BEACON_DURATION_16USEC  0x3
-
-#define PCIE_ICH8_SNOOP_ALL		PCIE_NO_SNOOP_ALL
-
-#define E1000_ICH_RAR_ENTRIES		7
-#define E1000_PCH2_RAR_ENTRIES		5 /* RAR[0], SHRA[0-3] */
-#define E1000_PCH_LPT_RAR_ENTRIES	12 /* RAR[0], SHRA[0-10] */
-
-#define PHY_PAGE_SHIFT 5
-#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
-			   ((reg) & MAX_PHY_REG_ADDRESS))
-#define IGP3_KMRN_DIAG  PHY_REG(770, 19) /* KMRN Diagnostic */
-#define IGP3_VR_CTRL    PHY_REG(776, 18) /* Voltage Regulator Control */
-
-#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS	0x0002
-#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300
-#define IGP3_VR_CTRL_MODE_SHUTDOWN	0x0200
-
-#define HV_LED_CONFIG		PHY_REG(768, 30) /* LED Configuration */
-
-#define SW_FLAG_TIMEOUT    1000 /* SW Semaphore flag timeout in milliseconds */
-
-/* SMBus Control Phy Register */
-#define CV_SMB_CTRL		PHY_REG(769, 23)
-#define CV_SMB_CTRL_FORCE_SMBUS	0x0001
-
-/* SMBus Address Phy Register */
-#define HV_SMB_ADDR            PHY_REG(768, 26)
-#define HV_SMB_ADDR_MASK       0x007F
-#define HV_SMB_ADDR_PEC_EN     0x0200
-#define HV_SMB_ADDR_VALID      0x0080
-#define HV_SMB_ADDR_FREQ_MASK           0x1100
-#define HV_SMB_ADDR_FREQ_LOW_SHIFT      8
-#define HV_SMB_ADDR_FREQ_HIGH_SHIFT     12
-
-/* PHY Power Management Control */
-#define HV_PM_CTRL		PHY_REG(770, 17)
-#define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA	0x100
-
-/* Intel Rapid Start Technology Support */
-#define I217_PROXY_CTRL                 BM_PHY_REG(BM_WUC_PAGE, 70)
-#define I217_PROXY_CTRL_AUTO_DISABLE    0x0080
-#define I217_SxCTRL                     PHY_REG(BM_PORT_CTRL_PAGE, 28)
-#define I217_SxCTRL_ENABLE_LPI_RESET    0x1000
-#define I217_CGFREG                     PHY_REG(772, 29)
-#define I217_CGFREG_ENABLE_MTA_RESET    0x0002
-#define I217_MEMPWR                     PHY_REG(772, 26)
-#define I217_MEMPWR_DISABLE_SMB_RELEASE 0x0010
-
-/* Strapping Option Register - RO */
-#define E1000_STRAP                     0x0000C
-#define E1000_STRAP_SMBUS_ADDRESS_MASK  0x00FE0000
-#define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17
-#define E1000_STRAP_SMT_FREQ_MASK       0x00003000
-#define E1000_STRAP_SMT_FREQ_SHIFT      12
-
-/* OEM Bits Phy Register */
-#define HV_OEM_BITS            PHY_REG(768, 25)
-#define HV_OEM_BITS_LPLU       0x0004 /* Low Power Link Up */
-#define HV_OEM_BITS_GBE_DIS    0x0040 /* Gigabit Disable */
-#define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */
-
-#define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */
-#define E1000_NVM_K1_ENABLE 0x1  /* NVM Enable K1 bit */
-
-/* KMRN Mode Control */
-#define HV_KMRN_MODE_CTRL      PHY_REG(769, 16)
-#define HV_KMRN_MDIO_SLOW      0x0400
-
-/* KMRN FIFO Control and Status */
-#define HV_KMRN_FIFO_CTRLSTA                  PHY_REG(770, 16)
-#define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_MASK    0x7000
-#define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_SHIFT   12
-
 /* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
 /* Offset 04h HSFSTS */
 union ich8_hws_flash_status {
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.h b/drivers/net/ethernet/intel/e1000e/ich8lan.h
new file mode 100644
index 000000000000..b6d3174d7d2d
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.h
@@ -0,0 +1,268 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2013 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000E_ICH8LAN_H_
+#define _E1000E_ICH8LAN_H_
+
+#define ICH_FLASH_GFPREG		0x0000
+#define ICH_FLASH_HSFSTS		0x0004
+#define ICH_FLASH_HSFCTL		0x0006
+#define ICH_FLASH_FADDR			0x0008
+#define ICH_FLASH_FDATA0		0x0010
+#define ICH_FLASH_PR0			0x0074
+
+/* Requires up to 10 seconds when MNG might be accessing part. */
+#define ICH_FLASH_READ_COMMAND_TIMEOUT	10000000
+#define ICH_FLASH_WRITE_COMMAND_TIMEOUT	10000000
+#define ICH_FLASH_ERASE_COMMAND_TIMEOUT	10000000
+#define ICH_FLASH_LINEAR_ADDR_MASK	0x00FFFFFF
+#define ICH_FLASH_CYCLE_REPEAT_COUNT	10
+
+#define ICH_CYCLE_READ			0
+#define ICH_CYCLE_WRITE			2
+#define ICH_CYCLE_ERASE			3
+
+#define FLASH_GFPREG_BASE_MASK		0x1FFF
+#define FLASH_SECTOR_ADDR_SHIFT		12
+
+#define ICH_FLASH_SEG_SIZE_256		256
+#define ICH_FLASH_SEG_SIZE_4K		4096
+#define ICH_FLASH_SEG_SIZE_8K		8192
+#define ICH_FLASH_SEG_SIZE_64K		65536
+
+#define E1000_ICH_FWSM_RSPCIPHY	0x00000040	/* Reset PHY on PCI Reset */
+/* FW established a valid mode */
+#define E1000_ICH_FWSM_FW_VALID	0x00008000
+#define E1000_ICH_FWSM_PCIM2PCI	0x01000000	/* ME PCIm-to-PCI active */
+#define E1000_ICH_FWSM_PCIM2PCI_COUNT	2000
+
+#define E1000_ICH_MNG_IAMT_MODE		0x2
+
+#define E1000_FWSM_WLOCK_MAC_MASK	0x0380
+#define E1000_FWSM_WLOCK_MAC_SHIFT	7
+
+/* Shared Receive Address Registers */
+#define E1000_SHRAL_PCH_LPT(_i)		(0x05408 + ((_i) * 8))
+#define E1000_SHRAH_PCH_LPT(_i)		(0x0540C + ((_i) * 8))
+
+#define ID_LED_DEFAULT_ICH8LAN	((ID_LED_DEF1_DEF2 << 12) | \
+				 (ID_LED_OFF1_OFF2 <<  8) | \
+				 (ID_LED_OFF1_ON2  <<  4) | \
+				 (ID_LED_DEF1_DEF2))
+
+#define E1000_ICH_NVM_SIG_WORD		0x13
+#define E1000_ICH_NVM_SIG_MASK		0xC000
+#define E1000_ICH_NVM_VALID_SIG_MASK	0xC0
+#define E1000_ICH_NVM_SIG_VALUE		0x80
+
+#define E1000_ICH8_LAN_INIT_TIMEOUT	1500
+
+#define E1000_FEXTNVM_SW_CONFIG		1
+#define E1000_FEXTNVM_SW_CONFIG_ICH8M	(1 << 27)	/* different on ICH8M */
+
+#define E1000_FEXTNVM3_PHY_CFG_COUNTER_MASK	0x0C000000
+#define E1000_FEXTNVM3_PHY_CFG_COUNTER_50MSEC	0x08000000
+
+#define E1000_FEXTNVM4_BEACON_DURATION_MASK	0x7
+#define E1000_FEXTNVM4_BEACON_DURATION_8USEC	0x7
+#define E1000_FEXTNVM4_BEACON_DURATION_16USEC	0x3
+
+#define PCIE_ICH8_SNOOP_ALL	PCIE_NO_SNOOP_ALL
+
+#define E1000_ICH_RAR_ENTRIES	7
+#define E1000_PCH2_RAR_ENTRIES	5	/* RAR[0], SHRA[0-3] */
+#define E1000_PCH_LPT_RAR_ENTRIES	12	/* RAR[0], SHRA[0-10] */
+
+#define PHY_PAGE_SHIFT		5
+#define PHY_REG(page, reg)	(((page) << PHY_PAGE_SHIFT) | \
+				 ((reg) & MAX_PHY_REG_ADDRESS))
+#define IGP3_KMRN_DIAG	PHY_REG(770, 19)	/* KMRN Diagnostic */
+#define IGP3_VR_CTRL	PHY_REG(776, 18)	/* Voltage Regulator Control */
+
+#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS		0x0002
+#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK	0x0300
+#define IGP3_VR_CTRL_MODE_SHUTDOWN		0x0200
+
+/* PHY Wakeup Registers and defines */
+#define BM_PORT_GEN_CFG		PHY_REG(BM_PORT_CTRL_PAGE, 17)
+#define BM_RCTL			PHY_REG(BM_WUC_PAGE, 0)
+#define BM_WUC			PHY_REG(BM_WUC_PAGE, 1)
+#define BM_WUFC			PHY_REG(BM_WUC_PAGE, 2)
+#define BM_WUS			PHY_REG(BM_WUC_PAGE, 3)
+#define BM_RAR_L(_i)		(BM_PHY_REG(BM_WUC_PAGE, 16 + ((_i) << 2)))
+#define BM_RAR_M(_i)		(BM_PHY_REG(BM_WUC_PAGE, 17 + ((_i) << 2)))
+#define BM_RAR_H(_i)		(BM_PHY_REG(BM_WUC_PAGE, 18 + ((_i) << 2)))
+#define BM_RAR_CTRL(_i)		(BM_PHY_REG(BM_WUC_PAGE, 19 + ((_i) << 2)))
+#define BM_MTA(_i)		(BM_PHY_REG(BM_WUC_PAGE, 128 + ((_i) << 1)))
+
+#define BM_RCTL_UPE		0x0001	/* Unicast Promiscuous Mode */
+#define BM_RCTL_MPE		0x0002	/* Multicast Promiscuous Mode */
+#define BM_RCTL_MO_SHIFT	3	/* Multicast Offset Shift */
+#define BM_RCTL_MO_MASK		(3 << 3)	/* Multicast Offset Mask */
+#define BM_RCTL_BAM		0x0020	/* Broadcast Accept Mode */
+#define BM_RCTL_PMCF		0x0040	/* Pass MAC Control Frames */
+#define BM_RCTL_RFCE		0x0080	/* Rx Flow Control Enable */
+
+#define HV_LED_CONFIG		PHY_REG(768, 30)	/* LED Configuration */
+#define HV_MUX_DATA_CTRL	PHY_REG(776, 16)
+#define HV_MUX_DATA_CTRL_GEN_TO_MAC	0x0400
+#define HV_MUX_DATA_CTRL_FORCE_SPEED	0x0004
+#define HV_STATS_PAGE	778
+/* Half-duplex collision counts */
+#define HV_SCC_UPPER	PHY_REG(HV_STATS_PAGE, 16)	/* Single Collision */
+#define HV_SCC_LOWER	PHY_REG(HV_STATS_PAGE, 17)
+#define HV_ECOL_UPPER	PHY_REG(HV_STATS_PAGE, 18)	/* Excessive Coll. */
+#define HV_ECOL_LOWER	PHY_REG(HV_STATS_PAGE, 19)
+#define HV_MCC_UPPER	PHY_REG(HV_STATS_PAGE, 20)	/* Multiple Collision */
+#define HV_MCC_LOWER	PHY_REG(HV_STATS_PAGE, 21)
+#define HV_LATECOL_UPPER PHY_REG(HV_STATS_PAGE, 23)	/* Late Collision */
+#define HV_LATECOL_LOWER PHY_REG(HV_STATS_PAGE, 24)
+#define HV_COLC_UPPER	PHY_REG(HV_STATS_PAGE, 25)	/* Collision */
+#define HV_COLC_LOWER	PHY_REG(HV_STATS_PAGE, 26)
+#define HV_DC_UPPER	PHY_REG(HV_STATS_PAGE, 27)	/* Defer Count */
+#define HV_DC_LOWER	PHY_REG(HV_STATS_PAGE, 28)
+#define HV_TNCRS_UPPER	PHY_REG(HV_STATS_PAGE, 29)	/* Tx with no CRS */
+#define HV_TNCRS_LOWER	PHY_REG(HV_STATS_PAGE, 30)
+
+#define E1000_FCRTV_PCH	0x05F40	/* PCH Flow Control Refresh Timer Value */
+
+#define E1000_NVM_K1_CONFIG	0x1B	/* NVM K1 Config Word */
+#define E1000_NVM_K1_ENABLE	0x1	/* NVM Enable K1 bit */
+
+/* SMBus Control Phy Register */
+#define CV_SMB_CTRL		PHY_REG(769, 23)
+#define CV_SMB_CTRL_FORCE_SMBUS	0x0001
+
+/* SMBus Address Phy Register */
+#define HV_SMB_ADDR		PHY_REG(768, 26)
+#define HV_SMB_ADDR_MASK	0x007F
+#define HV_SMB_ADDR_PEC_EN	0x0200
+#define HV_SMB_ADDR_VALID	0x0080
+#define HV_SMB_ADDR_FREQ_MASK		0x1100
+#define HV_SMB_ADDR_FREQ_LOW_SHIFT	8
+#define HV_SMB_ADDR_FREQ_HIGH_SHIFT	12
+
+/* Strapping Option Register - RO */
+#define E1000_STRAP			0x0000C
+#define E1000_STRAP_SMBUS_ADDRESS_MASK	0x00FE0000
+#define E1000_STRAP_SMBUS_ADDRESS_SHIFT	17
+#define E1000_STRAP_SMT_FREQ_MASK	0x00003000
+#define E1000_STRAP_SMT_FREQ_SHIFT	12
+
+/* OEM Bits Phy Register */
+#define HV_OEM_BITS		PHY_REG(768, 25)
+#define HV_OEM_BITS_LPLU	0x0004	/* Low Power Link Up */
+#define HV_OEM_BITS_GBE_DIS	0x0040	/* Gigabit Disable */
+#define HV_OEM_BITS_RESTART_AN	0x0400	/* Restart Auto-negotiation */
+
+/* KMRN Mode Control */
+#define HV_KMRN_MODE_CTRL	PHY_REG(769, 16)
+#define HV_KMRN_MDIO_SLOW	0x0400
+
+/* KMRN FIFO Control and Status */
+#define HV_KMRN_FIFO_CTRLSTA			PHY_REG(770, 16)
+#define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_MASK	0x7000
+#define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_SHIFT	12
+
+/* PHY Power Management Control */
+#define HV_PM_CTRL		PHY_REG(770, 17)
+#define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA	0x100
+
+#define SW_FLAG_TIMEOUT		1000	/* SW Semaphore flag timeout in ms */
+
+/* PHY Low Power Idle Control */
+#define I82579_LPI_CTRL				PHY_REG(772, 20)
+#define I82579_LPI_CTRL_100_ENABLE		0x2000
+#define I82579_LPI_CTRL_1000_ENABLE		0x4000
+#define I82579_LPI_CTRL_ENABLE_MASK		0x6000
+#define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
+
+/* Extended Management Interface (EMI) Registers */
+#define I82579_EMI_ADDR		0x10
+#define I82579_EMI_DATA		0x11
+#define I82579_LPI_UPDATE_TIMER	0x4805	/* in 40ns units + 40 ns base value */
+#define I82579_MSE_THRESHOLD	0x084F	/* 82579 Mean Square Error Threshold */
+#define I82577_MSE_THRESHOLD	0x0887	/* 82577 Mean Square Error Threshold */
+#define I82579_MSE_LINK_DOWN	0x2411	/* MSE count before dropping link */
+#define I82579_EEE_PCS_STATUS		0x182D	/* IEEE MMD Register 3.1 >> 8 */
+#define I82579_EEE_CAPABILITY		0x0410	/* IEEE MMD Register 3.20 */
+#define I82579_EEE_ADVERTISEMENT	0x040E	/* IEEE MMD Register 7.60 */
+#define I82579_EEE_LP_ABILITY		0x040F	/* IEEE MMD Register 7.61 */
+#define I82579_EEE_100_SUPPORTED	(1 << 1)	/* 100BaseTx EEE */
+#define I82579_EEE_1000_SUPPORTED	(1 << 2)	/* 1000BaseTx EEE */
+#define I217_EEE_PCS_STATUS	0x9401	/* IEEE MMD Register 3.1 */
+#define I217_EEE_CAPABILITY	0x8000	/* IEEE MMD Register 3.20 */
+#define I217_EEE_ADVERTISEMENT	0x8001	/* IEEE MMD Register 7.60 */
+#define I217_EEE_LP_ABILITY	0x8002	/* IEEE MMD Register 7.61 */
+
+#define E1000_EEE_RX_LPI_RCVD	0x0400	/* Tx LP idle received */
+#define E1000_EEE_TX_LPI_RCVD	0x0800	/* Rx LP idle received */
+
+/* Intel Rapid Start Technology Support */
+#define I217_PROXY_CTRL		BM_PHY_REG(BM_WUC_PAGE, 70)
+#define I217_PROXY_CTRL_AUTO_DISABLE	0x0080
+#define I217_SxCTRL			PHY_REG(BM_PORT_CTRL_PAGE, 28)
+#define I217_SxCTRL_ENABLE_LPI_RESET	0x1000
+#define I217_CGFREG			PHY_REG(772, 29)
+#define I217_CGFREG_ENABLE_MTA_RESET	0x0002
+#define I217_MEMPWR			PHY_REG(772, 26)
+#define I217_MEMPWR_DISABLE_SMB_RELEASE	0x0010
+
+/* Receive Address Initial CRC Calculation */
+#define E1000_PCH_RAICC(_n)	(0x05F50 + ((_n) * 4))
+
+/* Latency Tolerance Reporting */
+#define E1000_LTRV			0x000F8
+#define E1000_LTRV_SCALE_MAX		5
+#define E1000_LTRV_SCALE_FACTOR		5
+#define E1000_LTRV_REQ_SHIFT		15
+#define E1000_LTRV_NOSNOOP_SHIFT	16
+#define E1000_LTRV_SEND			(1 << 30)
+
+/* Proprietary Latency Tolerance Reporting PCI Capability */
+#define E1000_PCI_LTR_CAP_LPT		0xA8
+
+/* OBFF Control & Threshold Defines */
+#define E1000_SVCR_OFF_EN		0x00000001
+#define E1000_SVCR_OFF_MASKINT		0x00001000
+#define E1000_SVCR_OFF_TIMER_MASK	0xFFFF0000
+#define E1000_SVCR_OFF_TIMER_SHIFT	16
+#define E1000_SVT_OFF_HWM_MASK		0x0000001F
+
+void e1000e_write_protect_nvm_ich8lan(struct e1000_hw *hw);
+void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
+						  bool state);
+void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
+void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw);
+void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw);
+void e1000_resume_workarounds_pchlan(struct e1000_hw *hw);
+s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
+void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw);
+s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable);
+s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
+#endif /* _E1000E_ICH8LAN_H_ */
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index ae656f16c9fd..851685dd00d4 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -91,10 +91,6 @@ static const u16 e1000_igp_2_cable_length_table[] = {
 /* BM PHY Copper Specific Control 1 */
 #define BM_CS_CTRL1                       16
 
-#define HV_MUX_DATA_CTRL               PHY_REG(776, 16)
-#define HV_MUX_DATA_CTRL_GEN_TO_MAC    0x0400
-#define HV_MUX_DATA_CTRL_FORCE_SPEED   0x0004
-
 /**
  *  e1000e_check_reset_block_generic - Check if PHY reset is blocked
  *  @hw: pointer to the HW structure
-- 
cgit v1.2.3


From bdfe2da6aefd3961aac5c0cef76a030479e22f51 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Tue, 22 Jan 2013 08:44:19 +0000
Subject: e1000e: cosmetic move of function prototypes to the new mac.h

Move prototypes for functions which are applicable to all/most devices
supported by the driver and are specific to the MAC component of each
device to the new mac.h header file.  These function prototypes can be used
by other files in the driver and moving them to the MAC-specific file makes
it clearer to which component they are applicable.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/e1000.h | 37 ----------------
 drivers/net/ethernet/intel/e1000e/hw.h    |  2 +
 drivers/net/ethernet/intel/e1000e/mac.h   | 74 +++++++++++++++++++++++++++++++
 3 files changed, 76 insertions(+), 37 deletions(-)
 create mode 100644 drivers/net/ethernet/intel/e1000e/mac.h

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 7a383cd715d6..0ad4ff1d8ec6 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -538,48 +538,11 @@ extern s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
 
 extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
 
-extern s32 e1000e_check_for_copper_link(struct e1000_hw *hw);
-extern s32 e1000e_check_for_fiber_link(struct e1000_hw *hw);
-extern s32 e1000e_check_for_serdes_link(struct e1000_hw *hw);
-extern s32 e1000e_setup_led_generic(struct e1000_hw *hw);
-extern s32 e1000e_cleanup_led_generic(struct e1000_hw *hw);
-extern s32 e1000e_led_on_generic(struct e1000_hw *hw);
-extern s32 e1000e_led_off_generic(struct e1000_hw *hw);
-extern s32 e1000e_get_bus_info_pcie(struct e1000_hw *hw);
-extern void e1000_set_lan_id_multi_port_pcie(struct e1000_hw *hw);
-extern void e1000_set_lan_id_single_port(struct e1000_hw *hw);
-extern s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed, u16 *duplex);
-extern s32 e1000e_get_speed_and_duplex_fiber_serdes(struct e1000_hw *hw, u16 *speed, u16 *duplex);
-extern s32 e1000e_disable_pcie_master(struct e1000_hw *hw);
-extern s32 e1000e_get_auto_rd_done(struct e1000_hw *hw);
-extern s32 e1000e_id_led_init_generic(struct e1000_hw *hw);
-extern void e1000e_clear_hw_cntrs_base(struct e1000_hw *hw);
-extern s32 e1000e_setup_fiber_serdes_link(struct e1000_hw *hw);
 extern s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw);
 extern s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw);
-extern s32 e1000e_setup_link_generic(struct e1000_hw *hw);
-extern void e1000_clear_vfta_generic(struct e1000_hw *hw);
-extern void e1000e_init_rx_addrs(struct e1000_hw *hw, u16 rar_count);
-extern void e1000e_update_mc_addr_list_generic(struct e1000_hw *hw,
-					       u8 *mc_addr_list,
-					       u32 mc_addr_count);
-extern void e1000e_rar_set_generic(struct e1000_hw *hw, u8 *addr, u32 index);
-extern s32 e1000e_set_fc_watermarks(struct e1000_hw *hw);
-extern void e1000e_set_pcie_no_snoop(struct e1000_hw *hw, u32 no_snoop);
-extern s32 e1000e_get_hw_semaphore(struct e1000_hw *hw);
 extern s32 e1000e_valid_led_default(struct e1000_hw *hw, u16 *data);
-extern void e1000e_config_collision_dist_generic(struct e1000_hw *hw);
-extern s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw);
-extern s32 e1000e_force_mac_fc(struct e1000_hw *hw);
-extern s32 e1000e_blink_led_generic(struct e1000_hw *hw);
-extern void e1000_write_vfta_generic(struct e1000_hw *hw, u32 offset, u32 value);
-extern s32 e1000_check_alt_mac_addr_generic(struct e1000_hw *hw);
-extern void e1000e_reset_adaptive(struct e1000_hw *hw);
-extern void e1000e_update_adaptive(struct e1000_hw *hw);
-
 extern s32 e1000e_setup_copper_link(struct e1000_hw *hw);
 extern s32 e1000e_get_phy_id(struct e1000_hw *hw);
-extern void e1000e_put_hw_semaphore(struct e1000_hw *hw);
 extern s32 e1000e_check_reset_block_generic(struct e1000_hw *hw);
 extern s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw);
 extern s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw);
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 21a9cc36e467..0757f5bf26c4 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -763,6 +763,8 @@ struct e1000_host_mng_command_info {
 	u8 command_data[E1000_HI_MAX_MNG_DATA_LENGTH];
 };
 
+#include "mac.h"
+
 /* Function pointers for the MAC. */
 struct e1000_mac_operations {
 	s32  (*id_led_init)(struct e1000_hw *);
diff --git a/drivers/net/ethernet/intel/e1000e/mac.h b/drivers/net/ethernet/intel/e1000e/mac.h
new file mode 100644
index 000000000000..a61fee404ebe
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/mac.h
@@ -0,0 +1,74 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2013 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000E_MAC_H_
+#define _E1000E_MAC_H_
+
+s32 e1000e_blink_led_generic(struct e1000_hw *hw);
+s32 e1000e_check_for_copper_link(struct e1000_hw *hw);
+s32 e1000e_check_for_fiber_link(struct e1000_hw *hw);
+s32 e1000e_check_for_serdes_link(struct e1000_hw *hw);
+s32 e1000e_cleanup_led_generic(struct e1000_hw *hw);
+s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw);
+s32 e1000e_disable_pcie_master(struct e1000_hw *hw);
+s32 e1000e_force_mac_fc(struct e1000_hw *hw);
+s32 e1000e_get_auto_rd_done(struct e1000_hw *hw);
+s32 e1000e_get_bus_info_pcie(struct e1000_hw *hw);
+void e1000_set_lan_id_single_port(struct e1000_hw *hw);
+s32 e1000e_get_hw_semaphore(struct e1000_hw *hw);
+s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed,
+				       u16 *duplex);
+s32 e1000e_get_speed_and_duplex_fiber_serdes(struct e1000_hw *hw,
+					     u16 *speed, u16 *duplex);
+s32 e1000e_id_led_init_generic(struct e1000_hw *hw);
+s32 e1000e_led_on_generic(struct e1000_hw *hw);
+s32 e1000e_led_off_generic(struct e1000_hw *hw);
+void e1000e_update_mc_addr_list_generic(struct e1000_hw *hw,
+					u8 *mc_addr_list, u32 mc_addr_count);
+s32 e1000e_set_fc_watermarks(struct e1000_hw *hw);
+s32 e1000e_setup_fiber_serdes_link(struct e1000_hw *hw);
+s32 e1000e_setup_led_generic(struct e1000_hw *hw);
+s32 e1000e_setup_link_generic(struct e1000_hw *hw);
+s32 e1000e_validate_mdi_setting_generic(struct e1000_hw *hw);
+s32 e1000e_validate_mdi_setting_crossover_generic(struct e1000_hw *hw);
+
+void e1000e_clear_hw_cntrs_base(struct e1000_hw *hw);
+void e1000_clear_vfta_generic(struct e1000_hw *hw);
+void e1000e_init_rx_addrs(struct e1000_hw *hw, u16 rar_count);
+void e1000e_put_hw_semaphore(struct e1000_hw *hw);
+s32 e1000_check_alt_mac_addr_generic(struct e1000_hw *hw);
+void e1000e_reset_adaptive(struct e1000_hw *hw);
+void e1000e_set_pcie_no_snoop(struct e1000_hw *hw, u32 no_snoop);
+void e1000e_update_adaptive(struct e1000_hw *hw);
+void e1000_write_vfta_generic(struct e1000_hw *hw, u32 offset, u32 value);
+
+void e1000_set_lan_id_multi_port_pcie(struct e1000_hw *hw);
+void e1000e_rar_set_generic(struct e1000_hw *hw, u8 *addr, u32 index);
+void e1000e_config_collision_dist_generic(struct e1000_hw *hw);
+
+#endif
-- 
cgit v1.2.3


From 93b9f8bfd72818ddb540eb19333907989fb97043 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Tue, 22 Jan 2013 08:44:25 +0000
Subject: e1000e: cosmetic move of #defines and function prototypes to the new
 phy.h

Move #defines and function prototypes which are applicable to all/most
devices supported by the driver and are specific to the PHY component of
each device to the new phy.h header file.  These function prototypes can be
used by other files in the driver and moving them to the PHY-specific file
makes it clearer to which component they are applicable.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/e1000.h   |  95 -----------
 drivers/net/ethernet/intel/e1000e/ethtool.c |   1 -
 drivers/net/ethernet/intel/e1000e/hw.h      |  89 +---------
 drivers/net/ethernet/intel/e1000e/phy.c     |  38 -----
 drivers/net/ethernet/intel/e1000e/phy.h     | 242 ++++++++++++++++++++++++++++
 5 files changed, 243 insertions(+), 222 deletions(-)
 create mode 100644 drivers/net/ethernet/intel/e1000e/phy.h

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 0ad4ff1d8ec6..0573e15f6929 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -95,29 +95,6 @@ struct e1000_info;
 
 #define DEFAULT_JUMBO			9234
 
-/* BM/HV Specific Registers */
-#define BM_PORT_CTRL_PAGE                 769
-
-#define PHY_UPPER_SHIFT                   21
-#define BM_PHY_REG(page, reg) \
-	(((reg) & MAX_PHY_REG_ADDRESS) |\
-	 (((page) & 0xFFFF) << PHY_PAGE_SHIFT) |\
-	 (((reg) & ~MAX_PHY_REG_ADDRESS) << (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)))
-
-/* BM PHY Copper Specific Status */
-#define BM_CS_STATUS                      17
-#define BM_CS_STATUS_LINK_UP              0x0400
-#define BM_CS_STATUS_RESOLVED             0x0800
-#define BM_CS_STATUS_SPEED_MASK           0xC000
-#define BM_CS_STATUS_SPEED_1000           0x8000
-
-/* 82577 Mobile Phy Status Register */
-#define HV_M_STATUS                       26
-#define HV_M_STATUS_AUTONEG_COMPLETE      0x1000
-#define HV_M_STATUS_SPEED_MASK            0x0300
-#define HV_M_STATUS_SPEED_1000            0x0200
-#define HV_M_STATUS_LINK_UP               0x0040
-
 /* Time to wait before putting the device into D3 if there's no link (in ms). */
 #define LINK_TIMEOUT		100
 
@@ -538,79 +515,7 @@ extern s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
 
 extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
 
-extern s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw);
-extern s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw);
 extern s32 e1000e_valid_led_default(struct e1000_hw *hw, u16 *data);
-extern s32 e1000e_setup_copper_link(struct e1000_hw *hw);
-extern s32 e1000e_get_phy_id(struct e1000_hw *hw);
-extern s32 e1000e_check_reset_block_generic(struct e1000_hw *hw);
-extern s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw);
-extern s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw);
-extern s32 e1000e_get_phy_info_igp(struct e1000_hw *hw);
-extern s32 e1000_set_page_igp(struct e1000_hw *hw, u16 page);
-extern s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000e_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset,
-                                          u16 *data);
-extern s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw);
-extern s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active);
-extern s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
-extern s32 e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset,
-                                           u16 data);
-extern s32 e1000e_phy_sw_reset(struct e1000_hw *hw);
-extern s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw);
-extern s32 e1000e_get_cfg_done_generic(struct e1000_hw *hw);
-extern s32 e1000e_get_cable_length_m88(struct e1000_hw *hw);
-extern s32 e1000e_get_phy_info_m88(struct e1000_hw *hw);
-extern s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data);
-extern s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw);
-extern enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id);
-extern s32 e1000e_determine_phy_address(struct e1000_hw *hw);
-extern s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data);
-extern s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000_enable_phy_wakeup_reg_access_bm(struct e1000_hw *hw,
-						 u16 *phy_reg);
-extern s32 e1000_disable_phy_wakeup_reg_access_bm(struct e1000_hw *hw,
-						  u16 *phy_reg);
-extern s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data);
-extern void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl);
-extern s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data);
-extern s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset,
-                                        u16 data);
-extern s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset,
-                                       u16 *data);
-extern s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
-			       u32 usec_interval, bool *success);
-extern s32 e1000e_phy_reset_dsp(struct e1000_hw *hw);
-extern void e1000_power_up_phy_copper(struct e1000_hw *hw);
-extern void e1000_power_down_phy_copper(struct e1000_hw *hw);
-extern s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
-extern s32 e1000e_check_downshift(struct e1000_hw *hw);
-extern s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data);
-extern s32 e1000_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset,
-                                        u16 *data);
-extern s32 e1000_read_phy_reg_page_hv(struct e1000_hw *hw, u32 offset,
-				      u16 *data);
-extern s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data);
-extern s32 e1000_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset,
-                                         u16 data);
-extern s32 e1000_write_phy_reg_page_hv(struct e1000_hw *hw, u32 offset,
-				       u16 data);
-extern s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw);
-extern s32 e1000_copper_link_setup_82577(struct e1000_hw *hw);
-extern s32 e1000_check_polarity_82577(struct e1000_hw *hw);
-extern s32 e1000_get_phy_info_82577(struct e1000_hw *hw);
-extern s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw);
-extern s32 e1000_get_cable_length_82577(struct e1000_hw *hw);
-
-extern s32 e1000_check_polarity_m88(struct e1000_hw *hw);
-extern s32 e1000_get_phy_info_ife(struct e1000_hw *hw);
-extern s32 e1000_check_polarity_ife(struct e1000_hw *hw);
-extern s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
-extern s32 e1000_check_polarity_igp(struct e1000_hw *hw);
 extern void e1000e_ptp_init(struct e1000_adapter *adapter);
 extern void e1000e_ptp_remove(struct e1000_adapter *adapter);
 
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index c6c3e921686d..455e385120b4 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -1355,7 +1355,6 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 		e1e_rphy(hw, PHY_REG(776, 18), &phy_reg);
 		e1e_wphy(hw, PHY_REG(776, 18), phy_reg | 1);
 		/* Enable loopback on the PHY */
-#define I82577_PHY_LBK_CTRL          19
 		e1e_wphy(hw, I82577_PHY_LBK_CTRL, 0x8001);
 		break;
 	default:
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 0757f5bf26c4..5779ac4a4710 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -244,57 +244,6 @@ enum e1e_registers {
 	E1000_RXUDP     = 0x0B638, /* Timesync Rx UDP Port - RW */
 };
 
-#define E1000_MAX_PHY_ADDR		4
-
-/* IGP01E1000 Specific Registers */
-#define IGP01E1000_PHY_PORT_CONFIG	0x10 /* Port Config */
-#define IGP01E1000_PHY_PORT_STATUS	0x11 /* Status */
-#define IGP01E1000_PHY_PORT_CTRL	0x12 /* Control */
-#define IGP01E1000_PHY_LINK_HEALTH	0x13 /* PHY Link Health */
-#define IGP02E1000_PHY_POWER_MGMT	0x19 /* Power Management */
-#define IGP01E1000_PHY_PAGE_SELECT	0x1F /* Page Select */
-#define BM_PHY_PAGE_SELECT		22   /* Page Select for BM */
-#define IGP_PAGE_SHIFT			5
-#define PHY_REG_MASK			0x1F
-
-#define BM_WUC_PAGE			800
-#define BM_WUC_ADDRESS_OPCODE		0x11
-#define BM_WUC_DATA_OPCODE		0x12
-#define BM_WUC_ENABLE_PAGE		769
-#define BM_WUC_ENABLE_REG		17
-#define BM_WUC_ENABLE_BIT		(1 << 2)
-#define BM_WUC_HOST_WU_BIT		(1 << 4)
-#define BM_WUC_ME_WU_BIT		(1 << 5)
-
-#define IGP01E1000_PHY_PCS_INIT_REG	0x00B4
-#define IGP01E1000_PHY_POLARITY_MASK	0x0078
-
-#define IGP01E1000_PSCR_AUTO_MDIX	0x1000
-#define IGP01E1000_PSCR_FORCE_MDI_MDIX	0x2000 /* 0=MDI, 1=MDIX */
-
-#define IGP01E1000_PSCFR_SMART_SPEED	0x0080
-
-#define IGP02E1000_PM_SPD		0x0001 /* Smart Power Down */
-#define IGP02E1000_PM_D0_LPLU		0x0002 /* For D0a states */
-#define IGP02E1000_PM_D3_LPLU		0x0004 /* For all other states */
-
-#define IGP01E1000_PLHR_SS_DOWNGRADE	0x8000
-
-#define IGP01E1000_PSSR_POLARITY_REVERSED	0x0002
-#define IGP01E1000_PSSR_MDIX			0x0800
-#define IGP01E1000_PSSR_SPEED_MASK		0xC000
-#define IGP01E1000_PSSR_SPEED_1000MBPS		0xC000
-
-#define IGP02E1000_PHY_CHANNEL_NUM		4
-#define IGP02E1000_PHY_AGC_A			0x11B1
-#define IGP02E1000_PHY_AGC_B			0x12B1
-#define IGP02E1000_PHY_AGC_C			0x14B1
-#define IGP02E1000_PHY_AGC_D			0x18B1
-
-#define IGP02E1000_AGC_LENGTH_SHIFT	9 /* Course - 15:13, Fine - 12:9 */
-#define IGP02E1000_AGC_LENGTH_MASK	0x7F
-#define IGP02E1000_AGC_RANGE		15
-
 /* manage.c */
 #define E1000_VFTA_ENTRY_SHIFT		5
 #define E1000_VFTA_ENTRY_MASK		0x7F
@@ -320,43 +269,6 @@ enum e1e_registers {
 /* nvm.c */
 #define E1000_STM_OPCODE  0xDB00
 
-#define E1000_KMRNCTRLSTA_OFFSET	0x001F0000
-#define E1000_KMRNCTRLSTA_OFFSET_SHIFT	16
-#define E1000_KMRNCTRLSTA_REN		0x00200000
-#define E1000_KMRNCTRLSTA_CTRL_OFFSET	0x1    /* Kumeran Control */
-#define E1000_KMRNCTRLSTA_DIAG_OFFSET	0x3    /* Kumeran Diagnostic */
-#define E1000_KMRNCTRLSTA_TIMEOUTS	0x4    /* Kumeran Timeouts */
-#define E1000_KMRNCTRLSTA_INBAND_PARAM	0x9    /* Kumeran InBand Parameters */
-#define E1000_KMRNCTRLSTA_IBIST_DISABLE	0x0200 /* Kumeran IBIST Disable */
-#define E1000_KMRNCTRLSTA_DIAG_NELPBK	0x1000 /* Nearend Loopback mode */
-#define E1000_KMRNCTRLSTA_K1_CONFIG	0x7
-#define E1000_KMRNCTRLSTA_K1_ENABLE	0x0002
-#define E1000_KMRNCTRLSTA_HD_CTRL	0x10   /* Kumeran HD Control */
-
-#define IFE_PHY_EXTENDED_STATUS_CONTROL	0x10
-#define IFE_PHY_SPECIAL_CONTROL		0x11 /* 100BaseTx PHY Special Control */
-#define IFE_PHY_SPECIAL_CONTROL_LED	0x1B /* PHY Special and LED Control */
-#define IFE_PHY_MDIX_CONTROL		0x1C /* MDI/MDI-X Control */
-
-/* IFE PHY Extended Status Control */
-#define IFE_PESC_POLARITY_REVERSED	0x0100
-
-/* IFE PHY Special Control */
-#define IFE_PSC_AUTO_POLARITY_DISABLE		0x0010
-#define IFE_PSC_FORCE_POLARITY			0x0020
-
-/* IFE PHY Special Control and LED Control */
-#define IFE_PSCL_PROBE_MODE		0x0020
-#define IFE_PSCL_PROBE_LEDS_OFF		0x0006 /* Force LEDs 0 and 2 off */
-#define IFE_PSCL_PROBE_LEDS_ON		0x0007 /* Force LEDs 0 and 2 on */
-
-/* IFE PHY MDIX Control */
-#define IFE_PMC_MDIX_STATUS	0x0020 /* 1=MDI-X, 0=MDI */
-#define IFE_PMC_FORCE_MDIX	0x0040 /* 1=force MDI-X, 0=force MDI */
-#define IFE_PMC_AUTO_MDIX	0x0080 /* 1=enable auto MDI/MDI-X, 0=disable */
-
-#define E1000_CABLE_LENGTH_UNDEFINED	0xFF
-
 #define E1000_DEV_ID_82571EB_COPPER		0x105E
 #define E1000_DEV_ID_82571EB_FIBER		0x105F
 #define E1000_DEV_ID_82571EB_SERDES		0x1060
@@ -764,6 +676,7 @@ struct e1000_host_mng_command_info {
 };
 
 #include "mac.h"
+#include "phy.h"
 
 /* Function pointers for the MAC. */
 struct e1000_mac_operations {
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 851685dd00d4..a5ff13b9ef86 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -53,44 +53,6 @@ static const u16 e1000_igp_2_cable_length_table[] = {
 #define IGP02E1000_CABLE_LENGTH_TABLE_SIZE \
 		ARRAY_SIZE(e1000_igp_2_cable_length_table)
 
-#define BM_PHY_REG_PAGE(offset) \
-	((u16)(((offset) >> PHY_PAGE_SHIFT) & 0xFFFF))
-#define BM_PHY_REG_NUM(offset) \
-	((u16)(((offset) & MAX_PHY_REG_ADDRESS) |\
-	 (((offset) >> (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)) &\
-		~MAX_PHY_REG_ADDRESS)))
-
-#define HV_INTC_FC_PAGE_START             768
-#define I82578_ADDR_REG                   29
-#define I82577_ADDR_REG                   16
-#define I82577_CFG_REG                    22
-#define I82577_CFG_ASSERT_CRS_ON_TX       (1 << 15)
-#define I82577_CFG_ENABLE_DOWNSHIFT       (3 << 10) /* auto downshift 100/10 */
-#define I82577_CTRL_REG                   23
-
-/* 82577 specific PHY registers */
-#define I82577_PHY_CTRL_2            18
-#define I82577_PHY_STATUS_2          26
-#define I82577_PHY_DIAG_STATUS       31
-
-/* I82577 PHY Status 2 */
-#define I82577_PHY_STATUS2_REV_POLARITY   0x0400
-#define I82577_PHY_STATUS2_MDIX           0x0800
-#define I82577_PHY_STATUS2_SPEED_MASK     0x0300
-#define I82577_PHY_STATUS2_SPEED_1000MBPS 0x0200
-
-/* I82577 PHY Control 2 */
-#define I82577_PHY_CTRL2_MANUAL_MDIX      0x0200
-#define I82577_PHY_CTRL2_AUTO_MDI_MDIX    0x0400
-#define I82577_PHY_CTRL2_MDIX_CFG_MASK    0x0600
-
-/* I82577 PHY Diagnostics Status */
-#define I82577_DSTATUS_CABLE_LENGTH       0x03FC
-#define I82577_DSTATUS_CABLE_LENGTH_SHIFT 2
-
-/* BM PHY Copper Specific Control 1 */
-#define BM_CS_CTRL1                       16
-
 /**
  *  e1000e_check_reset_block_generic - Check if PHY reset is blocked
  *  @hw: pointer to the HW structure
diff --git a/drivers/net/ethernet/intel/e1000e/phy.h b/drivers/net/ethernet/intel/e1000e/phy.h
new file mode 100644
index 000000000000..f4f71b9991e3
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/phy.h
@@ -0,0 +1,242 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2013 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000E_PHY_H_
+#define _E1000E_PHY_H_
+
+s32 e1000e_check_downshift(struct e1000_hw *hw);
+s32 e1000_check_polarity_m88(struct e1000_hw *hw);
+s32 e1000_check_polarity_igp(struct e1000_hw *hw);
+s32 e1000_check_polarity_ife(struct e1000_hw *hw);
+s32 e1000e_check_reset_block_generic(struct e1000_hw *hw);
+s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw);
+s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw);
+s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw);
+s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw);
+s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
+s32 e1000e_get_cable_length_m88(struct e1000_hw *hw);
+s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw);
+s32 e1000e_get_cfg_done_generic(struct e1000_hw *hw);
+s32 e1000e_get_phy_id(struct e1000_hw *hw);
+s32 e1000e_get_phy_info_igp(struct e1000_hw *hw);
+s32 e1000e_get_phy_info_m88(struct e1000_hw *hw);
+s32 e1000_get_phy_info_ife(struct e1000_hw *hw);
+s32 e1000e_phy_sw_reset(struct e1000_hw *hw);
+void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl);
+s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw);
+s32 e1000e_phy_reset_dsp(struct e1000_hw *hw);
+s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000_set_page_igp(struct e1000_hw *hw, u16 page);
+s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active);
+s32 e1000e_setup_copper_link(struct e1000_hw *hw);
+s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
+				u32 usec_interval, bool *success);
+s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw);
+enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id);
+s32 e1000e_determine_phy_address(struct e1000_hw *hw);
+s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000_enable_phy_wakeup_reg_access_bm(struct e1000_hw *hw, u16 *phy_reg);
+s32 e1000_disable_phy_wakeup_reg_access_bm(struct e1000_hw *hw, u16 *phy_reg);
+s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data);
+void e1000_power_up_phy_copper(struct e1000_hw *hw);
+void e1000_power_down_phy_copper(struct e1000_hw *hw);
+s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000_read_phy_reg_page_hv(struct e1000_hw *hw, u32 offset, u16 *data);
+s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000_write_phy_reg_page_hv(struct e1000_hw *hw, u32 offset, u16 data);
+s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw);
+s32 e1000_copper_link_setup_82577(struct e1000_hw *hw);
+s32 e1000_check_polarity_82577(struct e1000_hw *hw);
+s32 e1000_get_phy_info_82577(struct e1000_hw *hw);
+s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw);
+s32 e1000_get_cable_length_82577(struct e1000_hw *hw);
+
+#define E1000_MAX_PHY_ADDR		8
+
+/* IGP01E1000 Specific Registers */
+#define IGP01E1000_PHY_PORT_CONFIG	0x10	/* Port Config */
+#define IGP01E1000_PHY_PORT_STATUS	0x11	/* Status */
+#define IGP01E1000_PHY_PORT_CTRL	0x12	/* Control */
+#define IGP01E1000_PHY_LINK_HEALTH	0x13	/* PHY Link Health */
+#define IGP02E1000_PHY_POWER_MGMT	0x19	/* Power Management */
+#define IGP01E1000_PHY_PAGE_SELECT	0x1F	/* Page Select */
+#define BM_PHY_PAGE_SELECT		22	/* Page Select for BM */
+#define IGP_PAGE_SHIFT			5
+#define PHY_REG_MASK			0x1F
+
+/* BM/HV Specific Registers */
+#define BM_PORT_CTRL_PAGE		769
+#define BM_WUC_PAGE			800
+#define BM_WUC_ADDRESS_OPCODE		0x11
+#define BM_WUC_DATA_OPCODE		0x12
+#define BM_WUC_ENABLE_PAGE		BM_PORT_CTRL_PAGE
+#define BM_WUC_ENABLE_REG		17
+#define BM_WUC_ENABLE_BIT		(1 << 2)
+#define BM_WUC_HOST_WU_BIT		(1 << 4)
+#define BM_WUC_ME_WU_BIT		(1 << 5)
+
+#define PHY_UPPER_SHIFT			21
+#define BM_PHY_REG(page, reg) \
+	(((reg) & MAX_PHY_REG_ADDRESS) |\
+	 (((page) & 0xFFFF) << PHY_PAGE_SHIFT) |\
+	 (((reg) & ~MAX_PHY_REG_ADDRESS) << (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)))
+#define BM_PHY_REG_PAGE(offset) \
+	((u16)(((offset) >> PHY_PAGE_SHIFT) & 0xFFFF))
+#define BM_PHY_REG_NUM(offset) \
+	((u16)(((offset) & MAX_PHY_REG_ADDRESS) |\
+	 (((offset) >> (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)) &\
+		~MAX_PHY_REG_ADDRESS)))
+
+#define HV_INTC_FC_PAGE_START		768
+#define I82578_ADDR_REG			29
+#define I82577_ADDR_REG			16
+#define I82577_CFG_REG			22
+#define I82577_CFG_ASSERT_CRS_ON_TX	(1 << 15)
+#define I82577_CFG_ENABLE_DOWNSHIFT	(3 << 10)	/* auto downshift */
+#define I82577_CTRL_REG			23
+
+/* 82577 specific PHY registers */
+#define I82577_PHY_CTRL_2		18
+#define I82577_PHY_LBK_CTRL		19
+#define I82577_PHY_STATUS_2		26
+#define I82577_PHY_DIAG_STATUS		31
+
+/* I82577 PHY Status 2 */
+#define I82577_PHY_STATUS2_REV_POLARITY		0x0400
+#define I82577_PHY_STATUS2_MDIX			0x0800
+#define I82577_PHY_STATUS2_SPEED_MASK		0x0300
+#define I82577_PHY_STATUS2_SPEED_1000MBPS	0x0200
+
+/* I82577 PHY Control 2 */
+#define I82577_PHY_CTRL2_MANUAL_MDIX		0x0200
+#define I82577_PHY_CTRL2_AUTO_MDI_MDIX		0x0400
+#define I82577_PHY_CTRL2_MDIX_CFG_MASK		0x0600
+
+/* I82577 PHY Diagnostics Status */
+#define I82577_DSTATUS_CABLE_LENGTH		0x03FC
+#define I82577_DSTATUS_CABLE_LENGTH_SHIFT	2
+
+/* BM PHY Copper Specific Control 1 */
+#define BM_CS_CTRL1			16
+
+/* BM PHY Copper Specific Status */
+#define BM_CS_STATUS			17
+#define BM_CS_STATUS_LINK_UP		0x0400
+#define BM_CS_STATUS_RESOLVED		0x0800
+#define BM_CS_STATUS_SPEED_MASK		0xC000
+#define BM_CS_STATUS_SPEED_1000		0x8000
+
+/* 82577 Mobile Phy Status Register */
+#define HV_M_STATUS			26
+#define HV_M_STATUS_AUTONEG_COMPLETE	0x1000
+#define HV_M_STATUS_SPEED_MASK		0x0300
+#define HV_M_STATUS_SPEED_1000		0x0200
+#define HV_M_STATUS_LINK_UP		0x0040
+
+#define IGP01E1000_PHY_PCS_INIT_REG	0x00B4
+#define IGP01E1000_PHY_POLARITY_MASK	0x0078
+
+#define IGP01E1000_PSCR_AUTO_MDIX	0x1000
+#define IGP01E1000_PSCR_FORCE_MDI_MDIX	0x2000	/* 0=MDI, 1=MDIX */
+
+#define IGP01E1000_PSCFR_SMART_SPEED	0x0080
+
+#define IGP02E1000_PM_SPD		0x0001	/* Smart Power Down */
+#define IGP02E1000_PM_D0_LPLU		0x0002	/* For D0a states */
+#define IGP02E1000_PM_D3_LPLU		0x0004	/* For all other states */
+
+#define IGP01E1000_PLHR_SS_DOWNGRADE	0x8000
+
+#define IGP01E1000_PSSR_POLARITY_REVERSED	0x0002
+#define IGP01E1000_PSSR_MDIX		0x0800
+#define IGP01E1000_PSSR_SPEED_MASK	0xC000
+#define IGP01E1000_PSSR_SPEED_1000MBPS	0xC000
+
+#define IGP02E1000_PHY_CHANNEL_NUM	4
+#define IGP02E1000_PHY_AGC_A		0x11B1
+#define IGP02E1000_PHY_AGC_B		0x12B1
+#define IGP02E1000_PHY_AGC_C		0x14B1
+#define IGP02E1000_PHY_AGC_D		0x18B1
+
+#define IGP02E1000_AGC_LENGTH_SHIFT	9	/* Course=15:13, Fine=12:9 */
+#define IGP02E1000_AGC_LENGTH_MASK	0x7F
+#define IGP02E1000_AGC_RANGE		15
+
+#define E1000_CABLE_LENGTH_UNDEFINED	0xFF
+
+#define E1000_KMRNCTRLSTA_OFFSET	0x001F0000
+#define E1000_KMRNCTRLSTA_OFFSET_SHIFT	16
+#define E1000_KMRNCTRLSTA_REN		0x00200000
+#define E1000_KMRNCTRLSTA_CTRL_OFFSET	0x1	/* Kumeran Control */
+#define E1000_KMRNCTRLSTA_DIAG_OFFSET	0x3	/* Kumeran Diagnostic */
+#define E1000_KMRNCTRLSTA_TIMEOUTS	0x4	/* Kumeran Timeouts */
+#define E1000_KMRNCTRLSTA_INBAND_PARAM	0x9	/* Kumeran InBand Parameters */
+#define E1000_KMRNCTRLSTA_IBIST_DISABLE	0x0200	/* Kumeran IBIST Disable */
+#define E1000_KMRNCTRLSTA_DIAG_NELPBK	0x1000	/* Nearend Loopback mode */
+#define E1000_KMRNCTRLSTA_K1_CONFIG	0x7
+#define E1000_KMRNCTRLSTA_K1_ENABLE	0x0002	/* enable K1 */
+#define E1000_KMRNCTRLSTA_HD_CTRL	0x10	/* Kumeran HD Control */
+
+#define IFE_PHY_EXTENDED_STATUS_CONTROL	0x10
+#define IFE_PHY_SPECIAL_CONTROL		0x11	/* 100BaseTx PHY Special Ctrl */
+#define IFE_PHY_SPECIAL_CONTROL_LED	0x1B	/* PHY Special and LED Ctrl */
+#define IFE_PHY_MDIX_CONTROL		0x1C	/* MDI/MDI-X Control */
+
+/* IFE PHY Extended Status Control */
+#define IFE_PESC_POLARITY_REVERSED	0x0100
+
+/* IFE PHY Special Control */
+#define IFE_PSC_AUTO_POLARITY_DISABLE	0x0010
+#define IFE_PSC_FORCE_POLARITY		0x0020
+
+/* IFE PHY Special Control and LED Control */
+#define IFE_PSCL_PROBE_MODE		0x0020
+#define IFE_PSCL_PROBE_LEDS_OFF		0x0006	/* Force LEDs 0 and 2 off */
+#define IFE_PSCL_PROBE_LEDS_ON		0x0007	/* Force LEDs 0 and 2 on */
+
+/* IFE PHY MDIX Control */
+#define IFE_PMC_MDIX_STATUS		0x0020	/* 1=MDI-X, 0=MDI */
+#define IFE_PMC_FORCE_MDIX		0x0040	/* 1=force MDI-X, 0=force MDI */
+#define IFE_PMC_AUTO_MDIX		0x0080	/* 1=enable auto, 0=disable */
+
+#endif
-- 
cgit v1.2.3


From d22631134d86b15689e6fea907aa97fffd88dbf6 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Tue, 22 Jan 2013 08:44:30 +0000
Subject: e1000e: cosmetic move of #defines and function prototypes to the new
 nvm.h

Move #defines and function prototypes which are applicable to all/most
devices supported by the driver and are specific to the NVM component of
each device to the new nvm.h header file.  These #defines and function
prototypes can be used by other files in the driver and moving them to the
NVM-specific file makes it clearer to which component they are applicable.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/e1000.h | 12 --------
 drivers/net/ethernet/intel/e1000e/hw.h    |  4 +--
 drivers/net/ethernet/intel/e1000e/nvm.h   | 47 +++++++++++++++++++++++++++++++
 3 files changed, 48 insertions(+), 15 deletions(-)
 create mode 100644 drivers/net/ethernet/intel/e1000e/nvm.h

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 0573e15f6929..00c2e8467b52 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -510,12 +510,8 @@ extern const struct e1000_info e1000_pch2_info;
 extern const struct e1000_info e1000_pch_lpt_info;
 extern const struct e1000_info e1000_es2_info;
 
-extern s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
-					 u32 pba_num_size);
-
 extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
 
-extern s32 e1000e_valid_led_default(struct e1000_hw *hw, u16 *data);
 extern void e1000e_ptp_init(struct e1000_adapter *adapter);
 extern void e1000e_ptp_remove(struct e1000_adapter *adapter);
 
@@ -544,15 +540,7 @@ static inline s32 e1e_wphy_locked(struct e1000_hw *hw, u32 offset, u16 data)
 	return hw->phy.ops.write_reg_locked(hw, offset, data);
 }
 
-extern s32 e1000e_acquire_nvm(struct e1000_hw *hw);
-extern s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
-extern s32 e1000e_update_nvm_checksum_generic(struct e1000_hw *hw);
-extern s32 e1000e_poll_eerd_eewr_done(struct e1000_hw *hw, int ee_reg);
-extern s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
-extern s32 e1000e_validate_nvm_checksum_generic(struct e1000_hw *hw);
-extern void e1000e_release_nvm(struct e1000_hw *hw);
 extern void e1000e_reload_nvm_generic(struct e1000_hw *hw);
-extern s32 e1000_read_mac_addr_generic(struct e1000_hw *hw);
 
 static inline s32 e1000e_read_mac_addr(struct e1000_hw *hw)
 {
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 5779ac4a4710..97b8746a08cd 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -266,9 +266,6 @@ enum e1e_registers {
 #define E1000_MNG_DHCP_COOKIE_STATUS_PARSING	0x1
 #define E1000_MNG_DHCP_COOKIE_STATUS_VLAN	0x2
 
-/* nvm.c */
-#define E1000_STM_OPCODE  0xDB00
-
 #define E1000_DEV_ID_82571EB_COPPER		0x105E
 #define E1000_DEV_ID_82571EB_FIBER		0x105F
 #define E1000_DEV_ID_82571EB_SERDES		0x1060
@@ -677,6 +674,7 @@ struct e1000_host_mng_command_info {
 
 #include "mac.h"
 #include "phy.h"
+#include "nvm.h"
 
 /* Function pointers for the MAC. */
 struct e1000_mac_operations {
diff --git a/drivers/net/ethernet/intel/e1000e/nvm.h b/drivers/net/ethernet/intel/e1000e/nvm.h
new file mode 100644
index 000000000000..45fc69561627
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/nvm.h
@@ -0,0 +1,47 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2013 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000E_NVM_H_
+#define _E1000E_NVM_H_
+
+s32 e1000e_acquire_nvm(struct e1000_hw *hw);
+
+s32 e1000e_poll_eerd_eewr_done(struct e1000_hw *hw, int ee_reg);
+s32 e1000_read_mac_addr_generic(struct e1000_hw *hw);
+s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
+				  u32 pba_num_size);
+s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
+s32 e1000e_valid_led_default(struct e1000_hw *hw, u16 *data);
+s32 e1000e_validate_nvm_checksum_generic(struct e1000_hw *hw);
+s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
+s32 e1000e_update_nvm_checksum_generic(struct e1000_hw *hw);
+void e1000e_release_nvm(struct e1000_hw *hw);
+
+#define E1000_STM_OPCODE	0xDB00
+
+#endif
-- 
cgit v1.2.3


From 948f97aca6700ea96647719185d83a0b7c312fc1 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Tue, 22 Jan 2013 08:44:35 +0000
Subject: e1000e: cosmetic move of #defines and prototypes to the new manage.h

Move #defines, function prototypes and data types which are applicable to
all/most devices supported by the driver but are specific to the
manageability component of each device to the new manage.h header file.
These #defines, function prototypes and data types can be used by other
files in the driver and moving them to the manageability-specific file
makes it clearer to which component they are applicable.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/e1000.h  |  6 ---
 drivers/net/ethernet/intel/e1000e/hw.h     | 23 +---------
 drivers/net/ethernet/intel/e1000e/manage.c | 13 ------
 drivers/net/ethernet/intel/e1000e/manage.h | 72 ++++++++++++++++++++++++++++++
 4 files changed, 73 insertions(+), 41 deletions(-)
 create mode 100644 drivers/net/ethernet/intel/e1000e/manage.h

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 00c2e8467b52..fcc758138b8a 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -510,8 +510,6 @@ extern const struct e1000_info e1000_pch2_info;
 extern const struct e1000_info e1000_pch_lpt_info;
 extern const struct e1000_info e1000_es2_info;
 
-extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
-
 extern void e1000e_ptp_init(struct e1000_adapter *adapter);
 extern void e1000e_ptp_remove(struct e1000_adapter *adapter);
 
@@ -575,10 +573,6 @@ static inline s32 e1000_get_phy_info(struct e1000_hw *hw)
 	return hw->phy.ops.get_info(hw);
 }
 
-extern bool e1000e_check_mng_mode_generic(struct e1000_hw *hw);
-extern bool e1000e_enable_tx_pkt_filtering(struct e1000_hw *hw);
-extern s32 e1000e_mng_write_dhcp_info(struct e1000_hw *hw, u8 *buffer, u16 length);
-
 static inline u32 __er32(struct e1000_hw *hw, unsigned long reg)
 {
 	return readl(hw->hw_addr + reg);
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 97b8746a08cd..de876bd85cdf 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -244,28 +244,6 @@ enum e1e_registers {
 	E1000_RXUDP     = 0x0B638, /* Timesync Rx UDP Port - RW */
 };
 
-/* manage.c */
-#define E1000_VFTA_ENTRY_SHIFT		5
-#define E1000_VFTA_ENTRY_MASK		0x7F
-#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK	0x1F
-
-#define E1000_HICR_EN			0x01  /* Enable bit - RO */
-/* Driver sets this bit when done to put command in RAM */
-#define E1000_HICR_C			0x02
-#define E1000_HICR_FW_RESET_ENABLE	0x40
-#define E1000_HICR_FW_RESET		0x80
-
-#define E1000_FWSM_MODE_MASK		0xE
-#define E1000_FWSM_MODE_SHIFT		1
-
-#define E1000_MNG_IAMT_MODE		0x3
-#define E1000_MNG_DHCP_COOKIE_LENGTH	0x10
-#define E1000_MNG_DHCP_COOKIE_OFFSET	0x6F0
-#define E1000_MNG_DHCP_COMMAND_TIMEOUT	10
-#define E1000_MNG_DHCP_TX_PAYLOAD_CMD	64
-#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING	0x1
-#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN	0x2
-
 #define E1000_DEV_ID_82571EB_COPPER		0x105E
 #define E1000_DEV_ID_82571EB_FIBER		0x105F
 #define E1000_DEV_ID_82571EB_SERDES		0x1060
@@ -675,6 +653,7 @@ struct e1000_host_mng_command_info {
 #include "mac.h"
 #include "phy.h"
 #include "nvm.h"
+#include "manage.h"
 
 /* Function pointers for the MAC. */
 struct e1000_mac_operations {
diff --git a/drivers/net/ethernet/intel/e1000e/manage.c b/drivers/net/ethernet/intel/e1000e/manage.c
index 4dae0dbda837..e4b0f1ef92f6 100644
--- a/drivers/net/ethernet/intel/e1000e/manage.c
+++ b/drivers/net/ethernet/intel/e1000e/manage.c
@@ -28,19 +28,6 @@
 
 #include "e1000.h"
 
-enum e1000_mng_mode {
-	e1000_mng_mode_none = 0,
-	e1000_mng_mode_asf,
-	e1000_mng_mode_pt,
-	e1000_mng_mode_ipmi,
-	e1000_mng_mode_host_if_only
-};
-
-#define E1000_FACTPS_MNGCG		0x20000000
-
-/* Intel(R) Active Management Technology signature */
-#define E1000_IAMT_SIGNATURE		0x544D4149
-
 /**
  *  e1000_calculate_checksum - Calculate checksum for buffer
  *  @buffer: pointer to EEPROM
diff --git a/drivers/net/ethernet/intel/e1000e/manage.h b/drivers/net/ethernet/intel/e1000e/manage.h
new file mode 100644
index 000000000000..326897c29ea8
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/manage.h
@@ -0,0 +1,72 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2013 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000E_MANAGE_H_
+#define _E1000E_MANAGE_H_
+
+bool e1000e_check_mng_mode_generic(struct e1000_hw *hw);
+bool e1000e_enable_tx_pkt_filtering(struct e1000_hw *hw);
+s32 e1000e_mng_write_dhcp_info(struct e1000_hw *hw, u8 *buffer, u16 length);
+bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
+
+enum e1000_mng_mode {
+	e1000_mng_mode_none = 0,
+	e1000_mng_mode_asf,
+	e1000_mng_mode_pt,
+	e1000_mng_mode_ipmi,
+	e1000_mng_mode_host_if_only
+};
+
+#define E1000_FACTPS_MNGCG			0x20000000
+
+#define E1000_FWSM_MODE_MASK			0xE
+#define E1000_FWSM_MODE_SHIFT			1
+
+#define E1000_MNG_IAMT_MODE			0x3
+#define E1000_MNG_DHCP_COOKIE_LENGTH		0x10
+#define E1000_MNG_DHCP_COOKIE_OFFSET		0x6F0
+#define E1000_MNG_DHCP_COMMAND_TIMEOUT		10
+#define E1000_MNG_DHCP_TX_PAYLOAD_CMD		64
+#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING	0x1
+#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN	0x2
+
+#define E1000_VFTA_ENTRY_SHIFT			5
+#define E1000_VFTA_ENTRY_MASK			0x7F
+#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK		0x1F
+
+#define E1000_HICR_EN			0x01	/* Enable bit - RO */
+/* Driver sets this bit when done to put command in RAM */
+#define E1000_HICR_C			0x02
+#define E1000_HICR_SV			0x04	/* Status Validity */
+#define E1000_HICR_FW_RESET_ENABLE	0x40
+#define E1000_HICR_FW_RESET		0x80
+
+/* Intel(R) Active Management Technology signature */
+#define E1000_IAMT_SIGNATURE		0x544D4149
+
+#endif
-- 
cgit v1.2.3


From c556d6072d99c96bbc091ea64712cf71468ce533 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Tue, 5 Feb 2013 00:30:59 -0800
Subject: e1000e: convert enums of register offsets and move #defines to regs.h

There are enough register offsets to warrant being in their own header
file, and doing so logically separates them from other header file content.
They have been converted from an enumerated data type to #defines as is
done in all the other Intel wired ethernet drivers.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/hw.h     | 212 +-----------------------
 drivers/net/ethernet/intel/e1000e/netdev.c |  12 --
 drivers/net/ethernet/intel/e1000e/regs.h   | 252 +++++++++++++++++++++++++++++
 3 files changed, 253 insertions(+), 223 deletions(-)
 create mode 100644 drivers/net/ethernet/intel/e1000e/regs.h

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index de876bd85cdf..1e6b889aee87 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -29,221 +29,11 @@
 #ifndef _E1000_HW_H_
 #define _E1000_HW_H_
 
+#include "regs.h"
 #include "defines.h"
 
 struct e1000_hw;
 
-enum e1e_registers {
-	E1000_CTRL     = 0x00000, /* Device Control - RW */
-	E1000_STATUS   = 0x00008, /* Device Status - RO */
-	E1000_EECD     = 0x00010, /* EEPROM/Flash Control - RW */
-	E1000_EERD     = 0x00014, /* EEPROM Read - RW */
-	E1000_CTRL_EXT = 0x00018, /* Extended Device Control - RW */
-	E1000_FLA      = 0x0001C, /* Flash Access - RW */
-	E1000_MDIC     = 0x00020, /* MDI Control - RW */
-	E1000_SCTL     = 0x00024, /* SerDes Control - RW */
-	E1000_FCAL     = 0x00028, /* Flow Control Address Low - RW */
-	E1000_FCAH     = 0x0002C, /* Flow Control Address High -RW */
-	E1000_FEXTNVM4 = 0x00024, /* Future Extended NVM 4 - RW */
-	E1000_FEXTNVM  = 0x00028, /* Future Extended NVM - RW */
-	E1000_FCT      = 0x00030, /* Flow Control Type - RW */
-	E1000_VET      = 0x00038, /* VLAN Ether Type - RW */
-	E1000_FEXTNVM3 = 0x0003C, /* Future Extended NVM 3 - RW */
-	E1000_ICR      = 0x000C0, /* Interrupt Cause Read - R/clr */
-	E1000_ITR      = 0x000C4, /* Interrupt Throttling Rate - RW */
-	E1000_ICS      = 0x000C8, /* Interrupt Cause Set - WO */
-	E1000_IMS      = 0x000D0, /* Interrupt Mask Set - RW */
-	E1000_IMC      = 0x000D8, /* Interrupt Mask Clear - WO */
-	E1000_IAM      = 0x000E0, /* Interrupt Acknowledge Auto Mask */
-	E1000_IVAR     = 0x000E4, /* Interrupt Vector Allocation - RW */
-	E1000_FEXTNVM7  = 0x000E4, /* Future Extended NVM 7 - RW */
-	E1000_LPIC     = 0x000FC, /* Low Power Idle Control - RW */
-	E1000_RCTL     = 0x00100, /* Rx Control - RW */
-	E1000_FCTTV    = 0x00170, /* Flow Control Transmit Timer Value - RW */
-	E1000_TXCW     = 0x00178, /* Tx Configuration Word - RW */
-	E1000_RXCW     = 0x00180, /* Rx Configuration Word - RO */
-	E1000_TCTL     = 0x00400, /* Tx Control - RW */
-	E1000_TCTL_EXT = 0x00404, /* Extended Tx Control - RW */
-	E1000_TIPG     = 0x00410, /* Tx Inter-packet gap -RW */
-	E1000_AIT      = 0x00458, /* Adaptive Interframe Spacing Throttle -RW */
-	E1000_LEDCTL   = 0x00E00, /* LED Control - RW */
-	E1000_EXTCNF_CTRL  = 0x00F00, /* Extended Configuration Control */
-	E1000_EXTCNF_SIZE  = 0x00F08, /* Extended Configuration Size */
-	E1000_PHY_CTRL     = 0x00F10, /* PHY Control Register in CSR */
-#define E1000_POEMB	E1000_PHY_CTRL	/* PHY OEM Bits */
-	E1000_PBA      = 0x01000, /* Packet Buffer Allocation - RW */
-	E1000_PBS      = 0x01008, /* Packet Buffer Size */
-	E1000_PBECCSTS = 0x0100C, /* Packet Buffer ECC Status - RW */
-	E1000_EEMNGCTL = 0x01010, /* MNG EEprom Control */
-	E1000_EEWR     = 0x0102C, /* EEPROM Write Register - RW */
-	E1000_FLOP     = 0x0103C, /* FLASH Opcode Register */
-	E1000_PBA_ECC  = 0x01100, /* PBA ECC Register */
-	E1000_ERT      = 0x02008, /* Early Rx Threshold - RW */
-	E1000_FCRTL    = 0x02160, /* Flow Control Receive Threshold Low - RW */
-	E1000_FCRTH    = 0x02168, /* Flow Control Receive Threshold High - RW */
-	E1000_PSRCTL   = 0x02170, /* Packet Split Receive Control - RW */
-/* Convenience macros
- *
- * Note: "_n" is the queue number of the register to be written to.
- *
- * Example usage:
- * E1000_RDBAL(current_rx_queue)
- */
-	E1000_RDBAL_BASE = 0x02800, /* Rx Descriptor Base Address Low - RW */
-#define E1000_RDBAL(_n)	(E1000_RDBAL_BASE + (_n << 8))
-	E1000_RDBAH_BASE = 0x02804, /* Rx Descriptor Base Address High - RW */
-#define E1000_RDBAH(_n)	(E1000_RDBAH_BASE + (_n << 8))
-	E1000_RDLEN_BASE = 0x02808, /* Rx Descriptor Length - RW */
-#define E1000_RDLEN(_n)	(E1000_RDLEN_BASE + (_n << 8))
-	E1000_RDH_BASE = 0x02810, /* Rx Descriptor Head - RW */
-#define E1000_RDH(_n)	(E1000_RDH_BASE + (_n << 8))
-	E1000_RDT_BASE = 0x02818, /* Rx Descriptor Tail - RW */
-#define E1000_RDT(_n)	(E1000_RDT_BASE + (_n << 8))
-	E1000_RDTR     = 0x02820, /* Rx Delay Timer - RW */
-	E1000_RXDCTL_BASE = 0x02828, /* Rx Descriptor Control - RW */
-#define E1000_RXDCTL(_n)   (E1000_RXDCTL_BASE + (_n << 8))
-	E1000_RADV     = 0x0282C, /* Rx Interrupt Absolute Delay Timer - RW */
-
-	E1000_KABGTXD  = 0x03004, /* AFE Band Gap Transmit Ref Data */
-	E1000_TDBAL_BASE = 0x03800, /* Tx Descriptor Base Address Low - RW */
-#define E1000_TDBAL(_n)	(E1000_TDBAL_BASE + (_n << 8))
-	E1000_TDBAH_BASE = 0x03804, /* Tx Descriptor Base Address High - RW */
-#define E1000_TDBAH(_n)	(E1000_TDBAH_BASE + (_n << 8))
-	E1000_TDLEN_BASE = 0x03808, /* Tx Descriptor Length - RW */
-#define E1000_TDLEN(_n)	(E1000_TDLEN_BASE + (_n << 8))
-	E1000_TDH_BASE = 0x03810, /* Tx Descriptor Head - RW */
-#define E1000_TDH(_n)	(E1000_TDH_BASE + (_n << 8))
-	E1000_TDT_BASE = 0x03818, /* Tx Descriptor Tail - RW */
-#define E1000_TDT(_n)	(E1000_TDT_BASE + (_n << 8))
-	E1000_TIDV     = 0x03820, /* Tx Interrupt Delay Value - RW */
-	E1000_TXDCTL_BASE = 0x03828, /* Tx Descriptor Control - RW */
-#define E1000_TXDCTL(_n)   (E1000_TXDCTL_BASE + (_n << 8))
-	E1000_TADV     = 0x0382C, /* Tx Interrupt Absolute Delay Val - RW */
-	E1000_TARC_BASE = 0x03840, /* Tx Arbitration Count (0) */
-#define E1000_TARC(_n)   (E1000_TARC_BASE + (_n << 8))
-	E1000_CRCERRS  = 0x04000, /* CRC Error Count - R/clr */
-	E1000_ALGNERRC = 0x04004, /* Alignment Error Count - R/clr */
-	E1000_SYMERRS  = 0x04008, /* Symbol Error Count - R/clr */
-	E1000_RXERRC   = 0x0400C, /* Receive Error Count - R/clr */
-	E1000_MPC      = 0x04010, /* Missed Packet Count - R/clr */
-	E1000_SCC      = 0x04014, /* Single Collision Count - R/clr */
-	E1000_ECOL     = 0x04018, /* Excessive Collision Count - R/clr */
-	E1000_MCC      = 0x0401C, /* Multiple Collision Count - R/clr */
-	E1000_LATECOL  = 0x04020, /* Late Collision Count - R/clr */
-	E1000_COLC     = 0x04028, /* Collision Count - R/clr */
-	E1000_DC       = 0x04030, /* Defer Count - R/clr */
-	E1000_TNCRS    = 0x04034, /* Tx-No CRS - R/clr */
-	E1000_SEC      = 0x04038, /* Sequence Error Count - R/clr */
-	E1000_CEXTERR  = 0x0403C, /* Carrier Extension Error Count - R/clr */
-	E1000_RLEC     = 0x04040, /* Receive Length Error Count - R/clr */
-	E1000_XONRXC   = 0x04048, /* XON Rx Count - R/clr */
-	E1000_XONTXC   = 0x0404C, /* XON Tx Count - R/clr */
-	E1000_XOFFRXC  = 0x04050, /* XOFF Rx Count - R/clr */
-	E1000_XOFFTXC  = 0x04054, /* XOFF Tx Count - R/clr */
-	E1000_FCRUC    = 0x04058, /* Flow Control Rx Unsupported Count- R/clr */
-	E1000_PRC64    = 0x0405C, /* Packets Rx (64 bytes) - R/clr */
-	E1000_PRC127   = 0x04060, /* Packets Rx (65-127 bytes) - R/clr */
-	E1000_PRC255   = 0x04064, /* Packets Rx (128-255 bytes) - R/clr */
-	E1000_PRC511   = 0x04068, /* Packets Rx (255-511 bytes) - R/clr */
-	E1000_PRC1023  = 0x0406C, /* Packets Rx (512-1023 bytes) - R/clr */
-	E1000_PRC1522  = 0x04070, /* Packets Rx (1024-1522 bytes) - R/clr */
-	E1000_GPRC     = 0x04074, /* Good Packets Rx Count - R/clr */
-	E1000_BPRC     = 0x04078, /* Broadcast Packets Rx Count - R/clr */
-	E1000_MPRC     = 0x0407C, /* Multicast Packets Rx Count - R/clr */
-	E1000_GPTC     = 0x04080, /* Good Packets Tx Count - R/clr */
-	E1000_GORCL    = 0x04088, /* Good Octets Rx Count Low - R/clr */
-	E1000_GORCH    = 0x0408C, /* Good Octets Rx Count High - R/clr */
-	E1000_GOTCL    = 0x04090, /* Good Octets Tx Count Low - R/clr */
-	E1000_GOTCH    = 0x04094, /* Good Octets Tx Count High - R/clr */
-	E1000_RNBC     = 0x040A0, /* Rx No Buffers Count - R/clr */
-	E1000_RUC      = 0x040A4, /* Rx Undersize Count - R/clr */
-	E1000_RFC      = 0x040A8, /* Rx Fragment Count - R/clr */
-	E1000_ROC      = 0x040AC, /* Rx Oversize Count - R/clr */
-	E1000_RJC      = 0x040B0, /* Rx Jabber Count - R/clr */
-	E1000_MGTPRC   = 0x040B4, /* Management Packets Rx Count - R/clr */
-	E1000_MGTPDC   = 0x040B8, /* Management Packets Dropped Count - R/clr */
-	E1000_MGTPTC   = 0x040BC, /* Management Packets Tx Count - R/clr */
-	E1000_TORL     = 0x040C0, /* Total Octets Rx Low - R/clr */
-	E1000_TORH     = 0x040C4, /* Total Octets Rx High - R/clr */
-	E1000_TOTL     = 0x040C8, /* Total Octets Tx Low - R/clr */
-	E1000_TOTH     = 0x040CC, /* Total Octets Tx High - R/clr */
-	E1000_TPR      = 0x040D0, /* Total Packets Rx - R/clr */
-	E1000_TPT      = 0x040D4, /* Total Packets Tx - R/clr */
-	E1000_PTC64    = 0x040D8, /* Packets Tx (64 bytes) - R/clr */
-	E1000_PTC127   = 0x040DC, /* Packets Tx (65-127 bytes) - R/clr */
-	E1000_PTC255   = 0x040E0, /* Packets Tx (128-255 bytes) - R/clr */
-	E1000_PTC511   = 0x040E4, /* Packets Tx (256-511 bytes) - R/clr */
-	E1000_PTC1023  = 0x040E8, /* Packets Tx (512-1023 bytes) - R/clr */
-	E1000_PTC1522  = 0x040EC, /* Packets Tx (1024-1522 Bytes) - R/clr */
-	E1000_MPTC     = 0x040F0, /* Multicast Packets Tx Count - R/clr */
-	E1000_BPTC     = 0x040F4, /* Broadcast Packets Tx Count - R/clr */
-	E1000_TSCTC    = 0x040F8, /* TCP Segmentation Context Tx - R/clr */
-	E1000_TSCTFC   = 0x040FC, /* TCP Segmentation Context Tx Fail - R/clr */
-	E1000_IAC      = 0x04100, /* Interrupt Assertion Count */
-	E1000_ICRXPTC  = 0x04104, /* Irq Cause Rx Packet Timer Expire Count */
-	E1000_ICRXATC  = 0x04108, /* Irq Cause Rx Abs Timer Expire Count */
-	E1000_ICTXPTC  = 0x0410C, /* Irq Cause Tx Packet Timer Expire Count */
-	E1000_ICTXATC  = 0x04110, /* Irq Cause Tx Abs Timer Expire Count */
-	E1000_ICTXQEC  = 0x04118, /* Irq Cause Tx Queue Empty Count */
-	E1000_ICTXQMTC = 0x0411C, /* Irq Cause Tx Queue MinThreshold Count */
-	E1000_ICRXDMTC = 0x04120, /* Irq Cause Rx Desc MinThreshold Count */
-	E1000_ICRXOC   = 0x04124, /* Irq Cause Receiver Overrun Count */
-	E1000_PCS_LCTL = 0x04208, /* PCS Link Control - RW */
-	E1000_PCS_LSTAT = 0x0420C, /* PCS Link Status - RO */
-	E1000_PCS_ANADV = 0x04218, /* AN advertisement - RW */
-	E1000_PCS_LPAB = 0x0421C, /* Link Partner Ability - RW */
-	E1000_RXCSUM   = 0x05000, /* Rx Checksum Control - RW */
-	E1000_RFCTL    = 0x05008, /* Receive Filter Control */
-	E1000_MTA      = 0x05200, /* Multicast Table Array - RW Array */
-	E1000_RAL_BASE = 0x05400, /* Receive Address Low - RW */
-#define E1000_RAL(_n)   (E1000_RAL_BASE + ((_n) * 8))
-#define E1000_RA        (E1000_RAL(0))
-	E1000_RAH_BASE = 0x05404, /* Receive Address High - RW */
-#define E1000_RAH(_n)   (E1000_RAH_BASE + ((_n) * 8))
-	E1000_SHRAL_BASE = 0x05438, /* Shared Receive Address Low - RW */
-#define E1000_SHRAL(_n)   (E1000_SHRAL_BASE + ((_n) * 8))
-	E1000_SHRAH_BASE = 0x0543C, /* Shared Receive Address High - RW */
-#define E1000_SHRAH(_n)   (E1000_SHRAH_BASE + ((_n) * 8))
-	E1000_VFTA     = 0x05600, /* VLAN Filter Table Array - RW Array */
-	E1000_WUC      = 0x05800, /* Wakeup Control - RW */
-	E1000_WUFC     = 0x05808, /* Wakeup Filter Control - RW */
-	E1000_WUS      = 0x05810, /* Wakeup Status - RO */
-	E1000_MRQC     = 0x05818, /* Multiple Receive Control - RW */
-	E1000_MANC     = 0x05820, /* Management Control - RW */
-	E1000_FFLT     = 0x05F00, /* Flexible Filter Length Table - RW Array */
-	E1000_CRC_OFFSET = 0x05F50, /* CRC Offset register */
-	E1000_HOST_IF  = 0x08800, /* Host Interface */
-
-	E1000_KMRNCTRLSTA = 0x00034, /* MAC-PHY interface - RW */
-	E1000_MANC2H    = 0x05860, /* Management Control To Host - RW */
-	E1000_MDEF_BASE = 0x05890, /* Management Decision Filters */
-#define E1000_MDEF(_n)   (E1000_MDEF_BASE + ((_n) * 4))
-	E1000_SW_FW_SYNC = 0x05B5C, /* Software-Firmware Synchronization - RW */
-	E1000_GCR	= 0x05B00, /* PCI-Ex Control */
-	E1000_GCR2      = 0x05B64, /* PCI-Ex Control #2 */
-	E1000_FACTPS    = 0x05B30, /* Function Active and Power State to MNG */
-	E1000_SWSM      = 0x05B50, /* SW Semaphore */
-	E1000_FWSM      = 0x05B54, /* FW Semaphore */
-	E1000_SWSM2     = 0x05B58, /* Driver-only SW semaphore */
-	E1000_RETA_BASE = 0x05C00, /* Redirection Table - RW */
-#define E1000_RETA(_n)	(E1000_RETA_BASE + ((_n) * 4))
-	E1000_RSSRK_BASE = 0x05C80, /* RSS Random Key - RW */
-#define E1000_RSSRK(_n)	(E1000_RSSRK_BASE + ((_n) * 4))
-	E1000_FFLT_DBG  = 0x05F04, /* Debug Register */
-	E1000_HICR      = 0x08F00, /* Host Interface Control */
-	E1000_SYSTIML   = 0x0B600, /* System time register Low - RO */
-	E1000_SYSTIMH   = 0x0B604, /* System time register High - RO */
-	E1000_TIMINCA   = 0x0B608, /* Increment attributes register - RW */
-	E1000_TSYNCTXCTL = 0x0B614, /* Tx Time Sync Control register - RW */
-	E1000_TXSTMPL   = 0x0B618, /* Tx timestamp value Low - RO */
-	E1000_TXSTMPH   = 0x0B61C, /* Tx timestamp value High - RO */
-	E1000_TSYNCRXCTL = 0x0B620, /* Rx Time Sync Control register - RW */
-	E1000_RXSTMPL   = 0x0B624, /* Rx timestamp Low - RO */
-	E1000_RXSTMPH   = 0x0B628, /* Rx timestamp High - RO */
-	E1000_RXMTRL    = 0x0B634, /* Timesync Rx EtherType and Msg Type - RW */
-	E1000_RXUDP     = 0x0B638, /* Timesync Rx UDP Port - RW */
-};
-
 #define E1000_DEV_ID_82571EB_COPPER		0x105E
 #define E1000_DEV_ID_82571EB_FIBER		0x105F
 #define E1000_DEV_ID_82571EB_SERDES		0x1060
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 6fcf9e8008c0..382b031e7b2a 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -86,18 +86,6 @@ struct e1000_reg_info {
 	char *name;
 };
 
-#define E1000_RDFH	0x02410	/* Rx Data FIFO Head - RW */
-#define E1000_RDFT	0x02418	/* Rx Data FIFO Tail - RW */
-#define E1000_RDFHS	0x02420	/* Rx Data FIFO Head Saved - RW */
-#define E1000_RDFTS	0x02428	/* Rx Data FIFO Tail Saved - RW */
-#define E1000_RDFPC	0x02430	/* Rx Data FIFO Packet Count - RW */
-
-#define E1000_TDFH	0x03410	/* Tx Data FIFO Head - RW */
-#define E1000_TDFT	0x03418	/* Tx Data FIFO Tail - RW */
-#define E1000_TDFHS	0x03420	/* Tx Data FIFO Head Saved - RW */
-#define E1000_TDFTS	0x03428	/* Tx Data FIFO Tail Saved - RW */
-#define E1000_TDFPC	0x03430	/* Tx Data FIFO Packet Count - RW */
-
 static const struct e1000_reg_info e1000_reg_info_tbl[] = {
 
 	/* General Registers */
diff --git a/drivers/net/ethernet/intel/e1000e/regs.h b/drivers/net/ethernet/intel/e1000e/regs.h
new file mode 100644
index 000000000000..794fe1497666
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/regs.h
@@ -0,0 +1,252 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2013 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000E_REGS_H_
+#define _E1000E_REGS_H_
+
+#define E1000_CTRL	0x00000	/* Device Control - RW */
+#define E1000_STATUS	0x00008	/* Device Status - RO */
+#define E1000_EECD	0x00010	/* EEPROM/Flash Control - RW */
+#define E1000_EERD	0x00014	/* EEPROM Read - RW */
+#define E1000_CTRL_EXT	0x00018	/* Extended Device Control - RW */
+#define E1000_FLA	0x0001C	/* Flash Access - RW */
+#define E1000_MDIC	0x00020	/* MDI Control - RW */
+#define E1000_SCTL	0x00024	/* SerDes Control - RW */
+#define E1000_FCAL	0x00028	/* Flow Control Address Low - RW */
+#define E1000_FCAH	0x0002C	/* Flow Control Address High -RW */
+#define E1000_FEXTNVM	0x00028	/* Future Extended NVM - RW */
+#define E1000_FEXTNVM3	0x0003C	/* Future Extended NVM 3 - RW */
+#define E1000_FEXTNVM4	0x00024	/* Future Extended NVM 4 - RW */
+#define E1000_FEXTNVM7	0x000E4	/* Future Extended NVM 7 - RW */
+#define E1000_FCT	0x00030	/* Flow Control Type - RW */
+#define E1000_VET	0x00038	/* VLAN Ether Type - RW */
+#define E1000_ICR	0x000C0	/* Interrupt Cause Read - R/clr */
+#define E1000_ITR	0x000C4	/* Interrupt Throttling Rate - RW */
+#define E1000_ICS	0x000C8	/* Interrupt Cause Set - WO */
+#define E1000_IMS	0x000D0	/* Interrupt Mask Set - RW */
+#define E1000_IMC	0x000D8	/* Interrupt Mask Clear - WO */
+#define E1000_IAM	0x000E0	/* Interrupt Acknowledge Auto Mask */
+#define E1000_IVAR	0x000E4	/* Interrupt Vector Allocation Register - RW */
+#define E1000_SVCR	0x000F0
+#define E1000_SVT	0x000F4
+#define E1000_LPIC	0x000FC	/* Low Power IDLE control */
+#define E1000_RCTL	0x00100	/* Rx Control - RW */
+#define E1000_FCTTV	0x00170	/* Flow Control Transmit Timer Value - RW */
+#define E1000_TXCW	0x00178	/* Tx Configuration Word - RW */
+#define E1000_RXCW	0x00180	/* Rx Configuration Word - RO */
+#define E1000_PBA_ECC	0x01100	/* PBA ECC Register */
+#define E1000_TCTL	0x00400	/* Tx Control - RW */
+#define E1000_TCTL_EXT	0x00404	/* Extended Tx Control - RW */
+#define E1000_TIPG	0x00410	/* Tx Inter-packet gap -RW */
+#define E1000_AIT	0x00458	/* Adaptive Interframe Spacing Throttle - RW */
+#define E1000_LEDCTL	0x00E00	/* LED Control - RW */
+#define E1000_EXTCNF_CTRL	0x00F00	/* Extended Configuration Control */
+#define E1000_EXTCNF_SIZE	0x00F08	/* Extended Configuration Size */
+#define E1000_PHY_CTRL	0x00F10	/* PHY Control Register in CSR */
+#define E1000_POEMB	E1000_PHY_CTRL	/* PHY OEM Bits */
+#define E1000_PBA	0x01000	/* Packet Buffer Allocation - RW */
+#define E1000_PBS	0x01008	/* Packet Buffer Size */
+#define E1000_PBECCSTS	0x0100C	/* Packet Buffer ECC Status - RW */
+#define E1000_EEMNGCTL	0x01010	/* MNG EEprom Control */
+#define E1000_EEWR	0x0102C	/* EEPROM Write Register - RW */
+#define E1000_FLOP	0x0103C	/* FLASH Opcode Register */
+#define E1000_ERT	0x02008	/* Early Rx Threshold - RW */
+#define E1000_FCRTL	0x02160	/* Flow Control Receive Threshold Low - RW */
+#define E1000_FCRTH	0x02168	/* Flow Control Receive Threshold High - RW */
+#define E1000_PSRCTL	0x02170	/* Packet Split Receive Control - RW */
+#define E1000_RDFH	0x02410	/* Rx Data FIFO Head - RW */
+#define E1000_RDFT	0x02418	/* Rx Data FIFO Tail - RW */
+#define E1000_RDFHS	0x02420	/* Rx Data FIFO Head Saved - RW */
+#define E1000_RDFTS	0x02428	/* Rx Data FIFO Tail Saved - RW */
+#define E1000_RDFPC	0x02430	/* Rx Data FIFO Packet Count - RW */
+/* Split and Replication Rx Control - RW */
+#define E1000_RDTR	0x02820	/* Rx Delay Timer - RW */
+#define E1000_RADV	0x0282C	/* Rx Interrupt Absolute Delay Timer - RW */
+/* Convenience macros
+ *
+ * Note: "_n" is the queue number of the register to be written to.
+ *
+ * Example usage:
+ * E1000_RDBAL_REG(current_rx_queue)
+ */
+#define E1000_RDBAL(_n)	((_n) < 4 ? (0x02800 + ((_n) * 0x100)) : \
+			 (0x0C000 + ((_n) * 0x40)))
+#define E1000_RDBAH(_n)	((_n) < 4 ? (0x02804 + ((_n) * 0x100)) : \
+			 (0x0C004 + ((_n) * 0x40)))
+#define E1000_RDLEN(_n)	((_n) < 4 ? (0x02808 + ((_n) * 0x100)) : \
+			 (0x0C008 + ((_n) * 0x40)))
+#define E1000_RDH(_n)	((_n) < 4 ? (0x02810 + ((_n) * 0x100)) : \
+			 (0x0C010 + ((_n) * 0x40)))
+#define E1000_RDT(_n)	((_n) < 4 ? (0x02818 + ((_n) * 0x100)) : \
+			 (0x0C018 + ((_n) * 0x40)))
+#define E1000_RXDCTL(_n)	((_n) < 4 ? (0x02828 + ((_n) * 0x100)) : \
+				 (0x0C028 + ((_n) * 0x40)))
+#define E1000_TDBAL(_n)	((_n) < 4 ? (0x03800 + ((_n) * 0x100)) : \
+			 (0x0E000 + ((_n) * 0x40)))
+#define E1000_TDBAH(_n)	((_n) < 4 ? (0x03804 + ((_n) * 0x100)) : \
+			 (0x0E004 + ((_n) * 0x40)))
+#define E1000_TDLEN(_n)	((_n) < 4 ? (0x03808 + ((_n) * 0x100)) : \
+			 (0x0E008 + ((_n) * 0x40)))
+#define E1000_TDH(_n)	((_n) < 4 ? (0x03810 + ((_n) * 0x100)) : \
+			 (0x0E010 + ((_n) * 0x40)))
+#define E1000_TDT(_n)	((_n) < 4 ? (0x03818 + ((_n) * 0x100)) : \
+			 (0x0E018 + ((_n) * 0x40)))
+#define E1000_TXDCTL(_n)	((_n) < 4 ? (0x03828 + ((_n) * 0x100)) : \
+				 (0x0E028 + ((_n) * 0x40)))
+#define E1000_TARC(_n)		(0x03840 + ((_n) * 0x100))
+#define E1000_KABGTXD		0x03004	/* AFE Band Gap Transmit Ref Data */
+#define E1000_RAL(_i)		(((_i) <= 15) ? (0x05400 + ((_i) * 8)) : \
+				 (0x054E0 + ((_i - 16) * 8)))
+#define E1000_RAH(_i)		(((_i) <= 15) ? (0x05404 + ((_i) * 8)) : \
+				 (0x054E4 + ((_i - 16) * 8)))
+#define E1000_SHRAL(_i)		(0x05438 + ((_i) * 8))
+#define E1000_SHRAH(_i)		(0x0543C + ((_i) * 8))
+#define E1000_TDFH		0x03410	/* Tx Data FIFO Head - RW */
+#define E1000_TDFT		0x03418	/* Tx Data FIFO Tail - RW */
+#define E1000_TDFHS		0x03420	/* Tx Data FIFO Head Saved - RW */
+#define E1000_TDFTS		0x03428	/* Tx Data FIFO Tail Saved - RW */
+#define E1000_TDFPC		0x03430	/* Tx Data FIFO Packet Count - RW */
+#define E1000_TIDV	0x03820	/* Tx Interrupt Delay Value - RW */
+#define E1000_TADV	0x0382C	/* Tx Interrupt Absolute Delay Val - RW */
+#define E1000_CRCERRS	0x04000	/* CRC Error Count - R/clr */
+#define E1000_ALGNERRC	0x04004	/* Alignment Error Count - R/clr */
+#define E1000_SYMERRS	0x04008	/* Symbol Error Count - R/clr */
+#define E1000_RXERRC	0x0400C	/* Receive Error Count - R/clr */
+#define E1000_MPC	0x04010	/* Missed Packet Count - R/clr */
+#define E1000_SCC	0x04014	/* Single Collision Count - R/clr */
+#define E1000_ECOL	0x04018	/* Excessive Collision Count - R/clr */
+#define E1000_MCC	0x0401C	/* Multiple Collision Count - R/clr */
+#define E1000_LATECOL	0x04020	/* Late Collision Count - R/clr */
+#define E1000_COLC	0x04028	/* Collision Count - R/clr */
+#define E1000_DC	0x04030	/* Defer Count - R/clr */
+#define E1000_TNCRS	0x04034	/* Tx-No CRS - R/clr */
+#define E1000_SEC	0x04038	/* Sequence Error Count - R/clr */
+#define E1000_CEXTERR	0x0403C	/* Carrier Extension Error Count - R/clr */
+#define E1000_RLEC	0x04040	/* Receive Length Error Count - R/clr */
+#define E1000_XONRXC	0x04048	/* XON Rx Count - R/clr */
+#define E1000_XONTXC	0x0404C	/* XON Tx Count - R/clr */
+#define E1000_XOFFRXC	0x04050	/* XOFF Rx Count - R/clr */
+#define E1000_XOFFTXC	0x04054	/* XOFF Tx Count - R/clr */
+#define E1000_FCRUC	0x04058	/* Flow Control Rx Unsupported Count- R/clr */
+#define E1000_PRC64	0x0405C	/* Packets Rx (64 bytes) - R/clr */
+#define E1000_PRC127	0x04060	/* Packets Rx (65-127 bytes) - R/clr */
+#define E1000_PRC255	0x04064	/* Packets Rx (128-255 bytes) - R/clr */
+#define E1000_PRC511	0x04068	/* Packets Rx (255-511 bytes) - R/clr */
+#define E1000_PRC1023	0x0406C	/* Packets Rx (512-1023 bytes) - R/clr */
+#define E1000_PRC1522	0x04070	/* Packets Rx (1024-1522 bytes) - R/clr */
+#define E1000_GPRC	0x04074	/* Good Packets Rx Count - R/clr */
+#define E1000_BPRC	0x04078	/* Broadcast Packets Rx Count - R/clr */
+#define E1000_MPRC	0x0407C	/* Multicast Packets Rx Count - R/clr */
+#define E1000_GPTC	0x04080	/* Good Packets Tx Count - R/clr */
+#define E1000_GORCL	0x04088	/* Good Octets Rx Count Low - R/clr */
+#define E1000_GORCH	0x0408C	/* Good Octets Rx Count High - R/clr */
+#define E1000_GOTCL	0x04090	/* Good Octets Tx Count Low - R/clr */
+#define E1000_GOTCH	0x04094	/* Good Octets Tx Count High - R/clr */
+#define E1000_RNBC	0x040A0	/* Rx No Buffers Count - R/clr */
+#define E1000_RUC	0x040A4	/* Rx Undersize Count - R/clr */
+#define E1000_RFC	0x040A8	/* Rx Fragment Count - R/clr */
+#define E1000_ROC	0x040AC	/* Rx Oversize Count - R/clr */
+#define E1000_RJC	0x040B0	/* Rx Jabber Count - R/clr */
+#define E1000_MGTPRC	0x040B4	/* Management Packets Rx Count - R/clr */
+#define E1000_MGTPDC	0x040B8	/* Management Packets Dropped Count - R/clr */
+#define E1000_MGTPTC	0x040BC	/* Management Packets Tx Count - R/clr */
+#define E1000_TORL	0x040C0	/* Total Octets Rx Low - R/clr */
+#define E1000_TORH	0x040C4	/* Total Octets Rx High - R/clr */
+#define E1000_TOTL	0x040C8	/* Total Octets Tx Low - R/clr */
+#define E1000_TOTH	0x040CC	/* Total Octets Tx High - R/clr */
+#define E1000_TPR	0x040D0	/* Total Packets Rx - R/clr */
+#define E1000_TPT	0x040D4	/* Total Packets Tx - R/clr */
+#define E1000_PTC64	0x040D8	/* Packets Tx (64 bytes) - R/clr */
+#define E1000_PTC127	0x040DC	/* Packets Tx (65-127 bytes) - R/clr */
+#define E1000_PTC255	0x040E0	/* Packets Tx (128-255 bytes) - R/clr */
+#define E1000_PTC511	0x040E4	/* Packets Tx (256-511 bytes) - R/clr */
+#define E1000_PTC1023	0x040E8	/* Packets Tx (512-1023 bytes) - R/clr */
+#define E1000_PTC1522	0x040EC	/* Packets Tx (1024-1522 Bytes) - R/clr */
+#define E1000_MPTC	0x040F0	/* Multicast Packets Tx Count - R/clr */
+#define E1000_BPTC	0x040F4	/* Broadcast Packets Tx Count - R/clr */
+#define E1000_TSCTC	0x040F8	/* TCP Segmentation Context Tx - R/clr */
+#define E1000_TSCTFC	0x040FC	/* TCP Segmentation Context Tx Fail - R/clr */
+#define E1000_IAC	0x04100	/* Interrupt Assertion Count */
+#define E1000_ICRXPTC	0x04104	/* Interrupt Cause Rx Pkt Timer Expire Count */
+#define E1000_ICRXATC	0x04108	/* Interrupt Cause Rx Abs Timer Expire Count */
+#define E1000_ICTXPTC	0x0410C	/* Interrupt Cause Tx Pkt Timer Expire Count */
+#define E1000_ICTXATC	0x04110	/* Interrupt Cause Tx Abs Timer Expire Count */
+#define E1000_ICTXQEC	0x04118	/* Interrupt Cause Tx Queue Empty Count */
+#define E1000_ICTXQMTC	0x0411C	/* Interrupt Cause Tx Queue Min Thresh Count */
+#define E1000_ICRXDMTC	0x04120	/* Interrupt Cause Rx Desc Min Thresh Count */
+#define E1000_ICRXOC	0x04124	/* Interrupt Cause Receiver Overrun Count */
+#define E1000_CRC_OFFSET	0x05F50	/* CRC Offset register */
+
+#define E1000_PCS_LCTL	0x04208	/* PCS Link Control - RW */
+#define E1000_PCS_LSTAT	0x0420C	/* PCS Link Status - RO */
+#define E1000_PCS_ANADV	0x04218	/* AN advertisement - RW */
+#define E1000_PCS_LPAB	0x0421C	/* Link Partner Ability - RW */
+#define E1000_RXCSUM	0x05000	/* Rx Checksum Control - RW */
+#define E1000_RFCTL	0x05008	/* Receive Filter Control */
+#define E1000_MTA	0x05200	/* Multicast Table Array - RW Array */
+#define E1000_RA	0x05400	/* Receive Address - RW Array */
+#define E1000_VFTA	0x05600	/* VLAN Filter Table Array - RW Array */
+#define E1000_WUC	0x05800	/* Wakeup Control - RW */
+#define E1000_WUFC	0x05808	/* Wakeup Filter Control - RW */
+#define E1000_WUS	0x05810	/* Wakeup Status - RO */
+#define E1000_MANC	0x05820	/* Management Control - RW */
+#define E1000_FFLT	0x05F00	/* Flexible Filter Length Table - RW Array */
+#define E1000_HOST_IF	0x08800	/* Host Interface */
+
+#define E1000_KMRNCTRLSTA	0x00034	/* MAC-PHY interface - RW */
+#define E1000_MANC2H		0x05860	/* Management Control To Host - RW */
+/* Management Decision Filters */
+#define E1000_MDEF(_n)		(0x05890 + (4 * (_n)))
+#define E1000_SW_FW_SYNC	0x05B5C	/* SW-FW Synchronization - RW */
+#define E1000_GCR	0x05B00	/* PCI-Ex Control */
+#define E1000_GCR2	0x05B64	/* PCI-Ex Control #2 */
+#define E1000_FACTPS	0x05B30	/* Function Active and Power State to MNG */
+#define E1000_SWSM	0x05B50	/* SW Semaphore */
+#define E1000_FWSM	0x05B54	/* FW Semaphore */
+/* Driver-only SW semaphore (not used by BOOT agents) */
+#define E1000_SWSM2	0x05B58
+#define E1000_FFLT_DBG	0x05F04	/* Debug Register */
+#define E1000_HICR	0x08F00	/* Host Interface Control */
+
+/* RSS registers */
+#define E1000_MRQC	0x05818	/* Multiple Receive Control - RW */
+#define E1000_RETA(_i)	(0x05C00 + ((_i) * 4))	/* Redirection Table - RW */
+#define E1000_RSSRK(_i)	(0x05C80 + ((_i) * 4))	/* RSS Random Key - RW */
+#define E1000_TSYNCRXCTL	0x0B620	/* Rx Time Sync Control register - RW */
+#define E1000_TSYNCTXCTL	0x0B614	/* Tx Time Sync Control register - RW */
+#define E1000_RXSTMPL	0x0B624	/* Rx timestamp Low - RO */
+#define E1000_RXSTMPH	0x0B628	/* Rx timestamp High - RO */
+#define E1000_TXSTMPL	0x0B618	/* Tx timestamp value Low - RO */
+#define E1000_TXSTMPH	0x0B61C	/* Tx timestamp value High - RO */
+#define E1000_SYSTIML	0x0B600	/* System time register Low - RO */
+#define E1000_SYSTIMH	0x0B604	/* System time register High - RO */
+#define E1000_TIMINCA	0x0B608	/* Increment attributes register - RW */
+#define E1000_RXMTRL	0x0B634	/* Time sync Rx EtherType and Msg Type - RW */
+#define E1000_RXUDP	0x0B638	/* Time Sync Rx UDP Port - RW */
+
+#endif
-- 
cgit v1.2.3


From a7a1d9da2980c2e86eba78d89a156f0b9d04ed4a Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Thu, 24 Jan 2013 00:50:18 +0000
Subject: e1000e: cleanup checkpatch braces checks

Resolve the following strict checkpatch checks:
CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
CHECK:BRACES: braces {} should be used on all arms of this statement

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/82571.c   | 1 -
 drivers/net/ethernet/intel/e1000e/ethtool.c | 5 ++---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 1 -
 drivers/net/ethernet/intel/e1000e/netdev.c  | 2 --
 drivers/net/ethernet/intel/e1000e/phy.c     | 1 -
 5 files changed, 2 insertions(+), 8 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index 1db7e3df43ea..2faffbde179e 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -1534,7 +1534,6 @@ static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw)
 	rxcw = er32(RXCW);
 
 	if ((rxcw & E1000_RXCW_SYNCH) && !(rxcw & E1000_RXCW_IV)) {
-
 		/* Receiver is synchronized with no invalid bits.  */
 		switch (mac->serdes_link_state) {
 		case e1000_serdes_link_autoneg_complete:
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 455e385120b4..2c1813737f6d 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -130,7 +130,6 @@ static int e1000_get_settings(struct net_device *netdev,
 	u32 speed;
 
 	if (hw->phy.media_type == e1000_media_type_copper) {
-
 		ecmd->supported = (SUPPORTED_10baseT_Half |
 				   SUPPORTED_10baseT_Full |
 				   SUPPORTED_100baseT_Half |
@@ -328,12 +327,12 @@ static int e1000_set_settings(struct net_device *netdev,
 	}
 
 	/* reset the link */
-
 	if (netif_running(adapter->netdev)) {
 		e1000e_down(adapter);
 		e1000e_up(adapter);
-	} else
+	} else {
 		e1000e_reset(adapter);
+	}
 
 	clear_bit(__E1000_RESETTING, &adapter->state);
 	return 0;
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 1e838b235e8a..dff7bff8b8e0 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -3991,7 +3991,6 @@ void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw)
 		 * The SMBus release must also be disabled on LCD reset.
 		 */
 		if (!(er32(FWSM) & E1000_ICH_FWSM_FW_VALID)) {
-
 			/* Enable proxy to reset only on power good. */
 			e1e_rphy_locked(hw, I217_PROXY_CTRL, &phy_reg);
 			phy_reg |= I217_PROXY_CTRL_AUTO_DISABLE;
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 382b031e7b2a..3f7dbd1cdb0f 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -87,7 +87,6 @@ struct e1000_reg_info {
 };
 
 static const struct e1000_reg_info e1000_reg_info_tbl[] = {
-
 	/* General Registers */
 	{E1000_CTRL, "CTRL"},
 	{E1000_STATUS, "STATUS"},
@@ -6394,7 +6393,6 @@ static void e1000_io_resume(struct pci_dev *pdev)
 	 */
 	if (!(adapter->flags & FLAG_HAS_AMT))
 		e1000e_get_hw_control(adapter);
-
 }
 
 static void e1000_print_device_info(struct e1000_adapter *adapter)
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index a5ff13b9ef86..0930c136aa31 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -2474,7 +2474,6 @@ s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data)
 	hw->phy.addr = 1;
 
 	if (offset > MAX_PHY_MULTI_PAGE_REG) {
-
 		/* Page is shifted left, PHY expects (page x 32) */
 		ret_val = e1000e_write_phy_reg_mdic(hw, BM_PHY_PAGE_SELECT,
 						    page);
-- 
cgit v1.2.3


From e792cd916cf74315bddb2c8b2323ef498cd7bfde Mon Sep 17 00:00:00 2001
From: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Date: Sun, 3 Feb 2013 14:03:55 +0000
Subject: e1000e: display a warning message when SmartSpeed works

Current e1000e driver doesn't tell nothing when Link Speed is downgraded due to
SmartSpeed.  As a result, users suspect that there is something wrong with
NIC.  If the cause of it is SmartSpeed, there is no means to replace NIC. This
patch make e1000e notify users that SmartSpeed worked.

Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 7 +++++++
 1 file changed, 7 insertions(+)

(limited to 'drivers/net/ethernet/intel/e1000e')

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 3f7dbd1cdb0f..a177b8b65c44 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -4830,6 +4830,13 @@ static void e1000_watchdog_task(struct work_struct *work)
 						   &adapter->link_speed,
 						   &adapter->link_duplex);
 			e1000_print_link_info(adapter);
+
+			/* check if SmartSpeed worked */
+			e1000e_check_downshift(hw);
+			if (phy->speed_downgraded)
+				netdev_warn(netdev,
+					    "Link Speed was downgraded by SmartSpeed\n");
+
 			/* On supported PHYs, check for duplex mismatch only
 			 * if link has autonegotiated at 10/100 half
 			 */
-- 
cgit v1.2.3