From fc7d76e4c0dc8746f56dcd0a7d9b62ce5e759c04 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 13 May 2014 18:34:04 -0700 Subject: mfd: twl4030-power: Fix hang on reboot if sleep configuration was loaded earlier Looks like we can still hit the issue of wrong load order of twl4030 configuration. If we have a sleep configuration loaded, and do a warm reset, the device can hang while initializing the wakeup12 sequence. We do have a warning message about wrong order of twl4030 configuration, but in this case it does not help as the sleep configuration was loaded during the previous boot and the state of twl4030 is maintained throughout the warm reset. Fix the issue by clearing any existing sleep configuration before we load the warm reset configuration. Signed-off-by: Tony Lindgren Signed-off-by: Lee Jones --- drivers/mfd/twl4030-power.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers/mfd') diff --git a/drivers/mfd/twl4030-power.c b/drivers/mfd/twl4030-power.c index 96162b62f3c0..1b30d8adc270 100644 --- a/drivers/mfd/twl4030-power.c +++ b/drivers/mfd/twl4030-power.c @@ -421,6 +421,12 @@ static int load_twl4030_script(struct twl4030_script *tscript, goto out; } if (tscript->flags & TWL4030_WAKEUP12_SCRIPT) { + /* Reset any existing sleep script to avoid hangs on reboot */ + err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, END_OF_SCRIPT, + R_SEQ_ADD_A2S); + if (err) + goto out; + err = twl4030_config_wakeup12_sequence(address); if (err) goto out; -- cgit v1.2.3 From 320572813ded2cc17581b22cdc5dc775aaf83f53 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 20 May 2014 11:17:53 -0700 Subject: mfd: twl4030-power: Fix some defines for SW_EVENTS We have these bits partially defined in two different places, so let's fix them up and add defines for the missing bits. These bits are the same for P1_SW_EVENTS, P2_SW_EVENTS and P3_SW_EVENTS. Signed-off-by: Tony Lindgren Signed-off-by: Lee Jones --- drivers/mfd/twl4030-power.c | 27 +++++++++++++++------------ 1 file changed, 15 insertions(+), 12 deletions(-) (limited to 'drivers/mfd') diff --git a/drivers/mfd/twl4030-power.c b/drivers/mfd/twl4030-power.c index 1b30d8adc270..0b037dca46a8 100644 --- a/drivers/mfd/twl4030-power.c +++ b/drivers/mfd/twl4030-power.c @@ -34,8 +34,15 @@ static u8 twl4030_start_script_address = 0x2b; -#define PWR_P1_SW_EVENTS 0x10 -#define PWR_DEVOFF (1 << 0) +/* Register bits for P1, P2 and P3_SW_EVENTS */ +#define PWR_STOPON_PRWON BIT(6) +#define PWR_STOPON_SYSEN BIT(5) +#define PWR_ENABLE_WARMRESET BIT(4) +#define PWR_LVL_WAKEUP BIT(3) +#define PWR_DEVACT BIT(2) +#define PWR_DEVSLP BIT(1) +#define PWR_DEVOFF BIT(0) + #define SEQ_OFFSYNC (1 << 0) #define PHY_TO_OFF_PM_MASTER(p) (p - 0x36) @@ -52,10 +59,6 @@ static u8 twl4030_start_script_address = 0x2b; #define R_CFG_P2_TRANSITION PHY_TO_OFF_PM_MASTER(0x37) #define R_CFG_P3_TRANSITION PHY_TO_OFF_PM_MASTER(0x38) -#define LVL_WAKEUP 0x08 - -#define ENABLE_WARMRESET (1<<4) - #define END_OF_SCRIPT 0x3f #define R_SEQ_ADD_A2S PHY_TO_OFF_PM_MASTER(0x55) @@ -196,7 +199,7 @@ static int twl4030_config_wakeup3_sequence(u8 address) err = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &data, R_P3_SW_EVENTS); if (err) goto out; - data |= LVL_WAKEUP; + data |= PWR_LVL_WAKEUP; err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, data, R_P3_SW_EVENTS); out: if (err) @@ -219,7 +222,7 @@ static int twl4030_config_wakeup12_sequence(u8 address) if (err) goto out; - data |= LVL_WAKEUP; + data |= PWR_LVL_WAKEUP; err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, data, R_P1_SW_EVENTS); if (err) goto out; @@ -228,7 +231,7 @@ static int twl4030_config_wakeup12_sequence(u8 address) if (err) goto out; - data |= LVL_WAKEUP; + data |= PWR_LVL_WAKEUP; err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, data, R_P2_SW_EVENTS); if (err) goto out; @@ -281,7 +284,7 @@ static int twl4030_config_warmreset_sequence(u8 address) if (err) goto out; - rd_data |= ENABLE_WARMRESET; + rd_data |= PWR_ENABLE_WARMRESET; err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, rd_data, R_P1_SW_EVENTS); if (err) goto out; @@ -290,7 +293,7 @@ static int twl4030_config_warmreset_sequence(u8 address) if (err) goto out; - rd_data |= ENABLE_WARMRESET; + rd_data |= PWR_ENABLE_WARMRESET; err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, rd_data, R_P2_SW_EVENTS); if (err) goto out; @@ -299,7 +302,7 @@ static int twl4030_config_warmreset_sequence(u8 address) if (err) goto out; - rd_data |= ENABLE_WARMRESET; + rd_data |= PWR_ENABLE_WARMRESET; err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, rd_data, R_P3_SW_EVENTS); out: if (err) -- cgit v1.2.3 From e7cd1d1eb16fcdf53001b926187a82f1f3e1a7e6 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 20 May 2014 11:17:54 -0700 Subject: mfd: twl4030-power: Add generic reset configuration The twl4030 PMIC needs to be configured properly for things like warm reset and deeper idle states so the PMIC manages the regulators properly based on the hardware triggers from the SoC. Earlier we have configured twl4030 using platform data, but we want to do it for device tree based booting also. In some cases configuring twl4030 is needed for things to work. For example, when rebooting an OMAP3530 at 125 MHz, it hangs. With this patch, TWL4030 will be reset when a warm reset occures, and OMAP3530 does not hang on reboot. Let's add device tree support and configure things for warm reset as the default when compatible = "ti,twl4030-power". More complicated configurations can be added to the driver based on other compatible flags. Note we now also make the pdata const like it should be. This allows use it for match->data with the device tree related functions. Based on earlier patch by Matthias Brugger and Lesly A M . Signed-off-by: Tony Lindgren Signed-off-by: Lee Jones --- .../devicetree/bindings/mfd/twl4030-power.txt | 7 +- drivers/mfd/twl4030-power.c | 109 ++++++++++++++++++--- include/linux/i2c/twl.h | 3 + 3 files changed, 105 insertions(+), 14 deletions(-) (limited to 'drivers/mfd') diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt index 8e15ec35ac99..b90611650cd9 100644 --- a/Documentation/devicetree/bindings/mfd/twl4030-power.txt +++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt @@ -5,7 +5,12 @@ to control the power resources, including power scripts. For now, the binding only supports the complete shutdown of the system after poweroff. Required properties: -- compatible : must be "ti,twl4030-power" +- compatible : must be one of the following + "ti,twl4030-power" + "ti,twl4030-power-reset" + +The use of ti,twl4030-power-reset is recommended at least on +3530 that needs a special configuration for warm reset to work. Optional properties: - ti,use_poweroff: With this flag, the chip will initiates an ACTIVE-to-OFF or diff --git a/drivers/mfd/twl4030-power.c b/drivers/mfd/twl4030-power.c index 0b037dca46a8..cb5b0cb8f933 100644 --- a/drivers/mfd/twl4030-power.c +++ b/drivers/mfd/twl4030-power.c @@ -29,6 +29,7 @@ #include #include #include +#include #include @@ -128,6 +129,40 @@ static u8 res_config_addrs[] = { [RES_MAIN_REF] = 0x94, }; +/* + * Usable values for .remap_sleep and .remap_off + * Based on table "5.3.3 Resource Operating modes" + */ +enum { + TWL_REMAP_OFF = 0, + TWL_REMAP_SLEEP = 8, + TWL_REMAP_ACTIVE = 9, +}; + +/* + * Macros to configure the PM register states for various resources. + * Note that we can make MSG_SINGULAR etc private to this driver once + * omap3 has been made DT only. + */ +#define TWL_DFLT_DELAY 2 /* typically 2 32 KiHz cycles */ +#define TWL_RESOURCE_SET(res, state) \ + { MSG_SINGULAR(DEV_GRP_NULL, (res), (state)), TWL_DFLT_DELAY } +#define TWL_RESOURCE_ON(res) TWL_RESOURCE_SET(res, RES_STATE_ACTIVE) +#define TWL_RESOURCE_OFF(res) TWL_RESOURCE_SET(res, RES_STATE_OFF) +#define TWL_RESOURCE_RESET(res) TWL_RESOURCE_SET(res, RES_STATE_WRST) +/* + * It seems that type1 and type2 is just the resource init order + * number for the type1 and type2 group. + */ +#define TWL_RESOURCE_GROUP_RESET(group, type1, type2) \ + { MSG_BROADCAST(DEV_GRP_NULL, (group), (type1), (type2), \ + RES_STATE_WRST), TWL_DFLT_DELAY } +#define TWL_REMAP_SLEEP(res, devgrp, typ, typ2) \ + { .resource = (res), .devgroup = (devgrp), \ + .type = (typ), .type2 = (typ2), \ + .remap_off = TWL_REMAP_OFF, \ + .remap_sleep = TWL_REMAP_SLEEP, } + static int twl4030_write_script_byte(u8 address, u8 byte) { int err; @@ -502,7 +537,8 @@ int twl4030_remove_script(u8 flags) return err; } -static int twl4030_power_configure_scripts(struct twl4030_power_data *pdata) +static int +twl4030_power_configure_scripts(const struct twl4030_power_data *pdata) { int err; int i; @@ -518,7 +554,8 @@ static int twl4030_power_configure_scripts(struct twl4030_power_data *pdata) return 0; } -static int twl4030_power_configure_resources(struct twl4030_power_data *pdata) +static int +twl4030_power_configure_resources(const struct twl4030_power_data *pdata) { struct twl4030_resconfig *resconfig = pdata->resource_config; int err; @@ -550,7 +587,7 @@ void twl4030_power_off(void) pr_err("TWL4030 Unable to power off\n"); } -static bool twl4030_power_use_poweroff(struct twl4030_power_data *pdata, +static bool twl4030_power_use_poweroff(const struct twl4030_power_data *pdata, struct device_node *node) { if (pdata && pdata->use_poweroff) @@ -562,10 +599,60 @@ static bool twl4030_power_use_poweroff(struct twl4030_power_data *pdata, return false; } +#ifdef CONFIG_OF + +/* Generic warm reset configuration for omap3 */ + +static struct twl4030_ins omap3_wrst_seq[] = { + TWL_RESOURCE_OFF(RES_NRES_PWRON), + TWL_RESOURCE_OFF(RES_RESET), + TWL_RESOURCE_RESET(RES_MAIN_REF), + TWL_RESOURCE_GROUP_RESET(RES_GRP_ALL, RES_TYPE_R0, RES_TYPE2_R2), + TWL_RESOURCE_RESET(RES_VUSB_3V1), + TWL_RESOURCE_GROUP_RESET(RES_GRP_ALL, RES_TYPE_R0, RES_TYPE2_R1), + TWL_RESOURCE_GROUP_RESET(RES_GRP_RC, RES_TYPE_ALL, RES_TYPE2_R0), + TWL_RESOURCE_ON(RES_RESET), + TWL_RESOURCE_ON(RES_NRES_PWRON), +}; + +static struct twl4030_script omap3_wrst_script = { + .script = omap3_wrst_seq, + .size = ARRAY_SIZE(omap3_wrst_seq), + .flags = TWL4030_WRST_SCRIPT, +}; + +static struct twl4030_script *omap3_reset_scripts[] = { + &omap3_wrst_script, +}; + +static struct twl4030_resconfig omap3_rconfig[] = { + TWL_REMAP_SLEEP(RES_HFCLKOUT, DEV_GRP_P3, -1, -1), + TWL_REMAP_SLEEP(RES_VDD1, DEV_GRP_P1, -1, -1), + TWL_REMAP_SLEEP(RES_VDD2, DEV_GRP_P1, -1, -1), + { 0, 0 }, +}; + +static struct twl4030_power_data omap3_reset = { + .scripts = omap3_reset_scripts, + .num = ARRAY_SIZE(omap3_reset_scripts), + .resource_config = omap3_rconfig, +}; + +static struct of_device_id twl4030_power_of_match[] = { + { + .compatible = "ti,twl4030-power-reset", + .data = &omap3_reset, + }, + { }, +}; +MODULE_DEVICE_TABLE(of, twl4030_power_of_match); +#endif /* CONFIG_OF */ + static int twl4030_power_probe(struct platform_device *pdev) { - struct twl4030_power_data *pdata = dev_get_platdata(&pdev->dev); + const struct twl4030_power_data *pdata = dev_get_platdata(&pdev->dev); struct device_node *node = pdev->dev.of_node; + const struct of_device_id *match; int err = 0; int err2 = 0; u8 val; @@ -586,8 +673,12 @@ static int twl4030_power_probe(struct platform_device *pdev) return err; } + match = of_match_device(of_match_ptr(twl4030_power_of_match), + &pdev->dev); + if (match && match->data) + pdata = match->data; + if (pdata) { - /* TODO: convert to device tree */ err = twl4030_power_configure_scripts(pdata); if (err) { pr_err("TWL4030 failed to load scripts\n"); @@ -637,14 +728,6 @@ static int twl4030_power_remove(struct platform_device *pdev) return 0; } -#ifdef CONFIG_OF -static const struct of_device_id twl4030_power_of_match[] = { - {.compatible = "ti,twl4030-power", }, - { }, -}; -MODULE_DEVICE_TABLE(of, twl4030_power_of_match); -#endif - static struct platform_driver twl4030_power_driver = { .driver = { .name = "twl4030_power", diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h index ade1c06d4ceb..5fe031375ed4 100644 --- a/include/linux/i2c/twl.h +++ b/include/linux/i2c/twl.h @@ -486,7 +486,10 @@ static inline int twl6030_mmc_card_detect(struct device *dev, int slot) #define RES_GRP_ALL 0x7 /* All resource groups */ #define RES_TYPE2_R0 0x0 +#define RES_TYPE2_R1 0x1 +#define RES_TYPE2_R2 0x2 +#define RES_TYPE_R0 0x0 #define RES_TYPE_ALL 0x7 /* Resource states */ -- cgit v1.2.3 From 76714d2c090f836fe005008116075a7b5bfde852 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 20 May 2014 11:17:54 -0700 Subject: mfd: twl4030-power: Add recommended idle configuration These settings are based on the "Recommended Sleep Sequences for the Zoom Platform". The settings assume most of the regulators are under control of Linux, and twl4030 only cuts off VDD1 and VDD2 during off-idle as Linux cannot do it. For any board specific changes to these, let's patch them in as changes to the generic data in the follow-up patches. This keeps the board specific changes small. Note that this does not consider the twl5030 errata 27 and 28. That can be added later on after it has been tested. For more information about errata 27 and 28. Signed-off-by: Tony Lindgren Signed-off-by: Lee Jones --- .../devicetree/bindings/mfd/twl4030-power.txt | 4 + drivers/mfd/twl4030-power.c | 106 +++++++++++++++++++++ 2 files changed, 110 insertions(+) (limited to 'drivers/mfd') diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt index b90611650cd9..bbd66039202a 100644 --- a/Documentation/devicetree/bindings/mfd/twl4030-power.txt +++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt @@ -8,10 +8,14 @@ Required properties: - compatible : must be one of the following "ti,twl4030-power" "ti,twl4030-power-reset" + "ti,twl4030-power-idle" The use of ti,twl4030-power-reset is recommended at least on 3530 that needs a special configuration for warm reset to work. +When using ti,twl4030-power-idle, the TI recommended configuration +for idle modes is loaded to the tlw4030 PMIC. + Optional properties: - ti,use_poweroff: With this flag, the chip will initiates an ACTIVE-to-OFF or SLEEP-to-OFF transition when the system poweroffs. diff --git a/drivers/mfd/twl4030-power.c b/drivers/mfd/twl4030-power.c index cb5b0cb8f933..2bfbb40ca9d2 100644 --- a/drivers/mfd/twl4030-power.c +++ b/drivers/mfd/twl4030-power.c @@ -145,6 +145,7 @@ enum { * omap3 has been made DT only. */ #define TWL_DFLT_DELAY 2 /* typically 2 32 KiHz cycles */ +#define TWL_DEV_GRP_P123 (DEV_GRP_P1 | DEV_GRP_P2 | DEV_GRP_P3) #define TWL_RESOURCE_SET(res, state) \ { MSG_SINGULAR(DEV_GRP_NULL, (res), (state)), TWL_DFLT_DELAY } #define TWL_RESOURCE_ON(res) TWL_RESOURCE_SET(res, RES_STATE_ACTIVE) @@ -154,14 +155,26 @@ enum { * It seems that type1 and type2 is just the resource init order * number for the type1 and type2 group. */ +#define TWL_RESOURCE_SET_ACTIVE(res, state) \ + { MSG_SINGULAR(DEV_GRP_NULL, (res), RES_STATE_ACTIVE), (state) } #define TWL_RESOURCE_GROUP_RESET(group, type1, type2) \ { MSG_BROADCAST(DEV_GRP_NULL, (group), (type1), (type2), \ RES_STATE_WRST), TWL_DFLT_DELAY } +#define TWL_RESOURCE_GROUP_SLEEP(group, type, type2) \ + { MSG_BROADCAST(DEV_GRP_NULL, (group), (type), (type2), \ + RES_STATE_SLEEP), TWL_DFLT_DELAY } +#define TWL_RESOURCE_GROUP_ACTIVE(group, type, type2) \ + { MSG_BROADCAST(DEV_GRP_NULL, (group), (type), (type2), \ + RES_STATE_ACTIVE), TWL_DFLT_DELAY } #define TWL_REMAP_SLEEP(res, devgrp, typ, typ2) \ { .resource = (res), .devgroup = (devgrp), \ .type = (typ), .type2 = (typ2), \ .remap_off = TWL_REMAP_OFF, \ .remap_sleep = TWL_REMAP_SLEEP, } +#define TWL_REMAP_OFF(res, devgrp, typ, typ2) \ + { .resource = (res), .devgroup = (devgrp), \ + .type = (typ), .type2 = (typ2), \ + .remap_off = TWL_REMAP_OFF, .remap_sleep = TWL_REMAP_OFF, } static int twl4030_write_script_byte(u8 address, u8 byte) { @@ -638,11 +651,104 @@ static struct twl4030_power_data omap3_reset = { .resource_config = omap3_rconfig, }; +/* Recommended generic default idle configuration for off-idle */ + +/* Broadcast message to put res to sleep */ +static struct twl4030_ins omap3_idle_sleep_on_seq[] = { + TWL_RESOURCE_GROUP_SLEEP(RES_GRP_ALL, RES_TYPE_ALL, 0), +}; + +static struct twl4030_script omap3_idle_sleep_on_script = { + .script = omap3_idle_sleep_on_seq, + .size = ARRAY_SIZE(omap3_idle_sleep_on_seq), + .flags = TWL4030_SLEEP_SCRIPT, +}; + +/* Broadcast message to put res to active */ +static struct twl4030_ins omap3_idle_wakeup_p12_seq[] = { + TWL_RESOURCE_GROUP_ACTIVE(RES_GRP_ALL, RES_TYPE_ALL, 0), +}; + +static struct twl4030_script omap3_idle_wakeup_p12_script = { + .script = omap3_idle_wakeup_p12_seq, + .size = ARRAY_SIZE(omap3_idle_wakeup_p12_seq), + .flags = TWL4030_WAKEUP12_SCRIPT, +}; + +/* Broadcast message to put res to active */ +static struct twl4030_ins omap3_idle_wakeup_p3_seq[] = { + TWL_RESOURCE_SET_ACTIVE(RES_CLKEN, 0x37), + TWL_RESOURCE_GROUP_ACTIVE(RES_GRP_ALL, RES_TYPE_ALL, 0), +}; + +static struct twl4030_script omap3_idle_wakeup_p3_script = { + .script = omap3_idle_wakeup_p3_seq, + .size = ARRAY_SIZE(omap3_idle_wakeup_p3_seq), + .flags = TWL4030_WAKEUP3_SCRIPT, +}; + +static struct twl4030_script *omap3_idle_scripts[] = { + &omap3_idle_wakeup_p12_script, + &omap3_idle_wakeup_p3_script, + &omap3_wrst_script, + &omap3_idle_sleep_on_script, +}; + +/* + * Recommended configuration based on "Recommended Sleep + * Sequences for the Zoom Platform": + * http://omappedia.com/wiki/File:Recommended_Sleep_Sequences_Zoom.pdf + * Note that the type1 and type2 seem to be just the init order number + * for type1 and type2 groups as specified in the document mentioned + * above. + */ +static struct twl4030_resconfig omap3_idle_rconfig[] = { + TWL_REMAP_SLEEP(RES_VAUX1, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VAUX2, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VAUX3, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VAUX4, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VMMC1, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VMMC2, DEV_GRP_NULL, 0, 0), + TWL_REMAP_OFF(RES_VPLL1, DEV_GRP_P1, 3, 1), + TWL_REMAP_SLEEP(RES_VPLL2, DEV_GRP_P1, 0, 0), + TWL_REMAP_SLEEP(RES_VSIM, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VDAC, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VINTANA1, TWL_DEV_GRP_P123, 1, 2), + TWL_REMAP_SLEEP(RES_VINTANA2, TWL_DEV_GRP_P123, 0, 2), + TWL_REMAP_SLEEP(RES_VINTDIG, TWL_DEV_GRP_P123, 1, 2), + TWL_REMAP_SLEEP(RES_VIO, TWL_DEV_GRP_P123, 2, 2), + TWL_REMAP_OFF(RES_VDD1, DEV_GRP_P1, 4, 1), + TWL_REMAP_OFF(RES_VDD2, DEV_GRP_P1, 3, 1), + TWL_REMAP_SLEEP(RES_VUSB_1V5, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VUSB_1V8, DEV_GRP_NULL, 0, 0), + TWL_REMAP_SLEEP(RES_VUSB_3V1, TWL_DEV_GRP_P123, 0, 0), + /* Resource #20 USB charge pump skipped */ + TWL_REMAP_SLEEP(RES_REGEN, TWL_DEV_GRP_P123, 2, 1), + TWL_REMAP_SLEEP(RES_NRES_PWRON, TWL_DEV_GRP_P123, 0, 1), + TWL_REMAP_SLEEP(RES_CLKEN, TWL_DEV_GRP_P123, 3, 2), + TWL_REMAP_SLEEP(RES_SYSEN, TWL_DEV_GRP_P123, 6, 1), + TWL_REMAP_SLEEP(RES_HFCLKOUT, DEV_GRP_P3, 0, 2), + TWL_REMAP_SLEEP(RES_32KCLKOUT, TWL_DEV_GRP_P123, 0, 0), + TWL_REMAP_SLEEP(RES_RESET, TWL_DEV_GRP_P123, 6, 0), + TWL_REMAP_SLEEP(RES_MAIN_REF, TWL_DEV_GRP_P123, 0, 0), + { /* Terminator */ }, +}; + +static struct twl4030_power_data omap3_idle = { + .scripts = omap3_idle_scripts, + .num = ARRAY_SIZE(omap3_idle_scripts), + .resource_config = omap3_idle_rconfig, +}; + static struct of_device_id twl4030_power_of_match[] = { { .compatible = "ti,twl4030-power-reset", .data = &omap3_reset, }, + { + .compatible = "ti,twl4030-power-idle", + .data = &omap3_idle, + }, { }, }; MODULE_DEVICE_TABLE(of, twl4030_power_of_match); -- cgit v1.2.3 From 482e7db160df713a2d1d4c7ee9fffad92008283f Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 20 May 2014 11:17:54 -0700 Subject: mfd: twl4030-power: Add support for board specific configuration With the recommended twl4030 configuration added, we can now add board specific changes as modifications to the recommended configuration. Note that the data is private to this driver, and the data must always have a NULL resource in the sentinel. Signed-off-by: Tony Lindgren Signed-off-by: Lee Jones --- drivers/mfd/twl4030-power.c | 21 +++++++++++++++++++++ include/linux/i2c/twl.h | 1 + 2 files changed, 22 insertions(+) (limited to 'drivers/mfd') diff --git a/drivers/mfd/twl4030-power.c b/drivers/mfd/twl4030-power.c index 2bfbb40ca9d2..4846c7b48ebb 100644 --- a/drivers/mfd/twl4030-power.c +++ b/drivers/mfd/twl4030-power.c @@ -567,13 +567,34 @@ twl4030_power_configure_scripts(const struct twl4030_power_data *pdata) return 0; } +static void twl4030_patch_rconfig(struct twl4030_resconfig *common, + struct twl4030_resconfig *board) +{ + while (common->resource) { + struct twl4030_resconfig *b = board; + + while (b->resource) { + if (b->resource == common->resource) { + *common = *b; + break; + } + b++; + } + common++; + } +} + static int twl4030_power_configure_resources(const struct twl4030_power_data *pdata) { struct twl4030_resconfig *resconfig = pdata->resource_config; + struct twl4030_resconfig *boardconf = pdata->board_config; int err; if (resconfig) { + if (boardconf) + twl4030_patch_rconfig(resconfig, boardconf); + while (resconfig->resource) { err = twl4030_configure_resource(resconfig); if (err) diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h index 5fe031375ed4..57fe782bf031 100644 --- a/include/linux/i2c/twl.h +++ b/include/linux/i2c/twl.h @@ -662,6 +662,7 @@ struct twl4030_power_data { struct twl4030_script **scripts; unsigned num; struct twl4030_resconfig *resource_config; + struct twl4030_resconfig *board_config; #define TWL4030_RESCONFIG_UNDEF ((u8)-1) bool use_poweroff; /* Board is wired for TWL poweroff */ }; -- cgit v1.2.3 From 43fef47f94a1ae46fb2720dada32fa3b5547bee2 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 13 May 2014 18:34:09 -0700 Subject: mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle Some oscillators can be turned off during off-idle saving few a little bit power at the cost of the oscillator start up latency. If you board can do this, you can now enable it by using the ti,twl4030-power-idle-osc-off compatible flag. Signed-off-by: Tony Lindgren Signed-off-by: Lee Jones --- Documentation/devicetree/bindings/mfd/twl4030-power.txt | 6 ++++++ drivers/mfd/twl4030-power.c | 17 +++++++++++++++++ 2 files changed, 23 insertions(+) (limited to 'drivers/mfd') diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt index bbd66039202a..b9ee7b98d3e2 100644 --- a/Documentation/devicetree/bindings/mfd/twl4030-power.txt +++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt @@ -9,6 +9,7 @@ Required properties: "ti,twl4030-power" "ti,twl4030-power-reset" "ti,twl4030-power-idle" + "ti,twl4030-power-idle-osc-off" The use of ti,twl4030-power-reset is recommended at least on 3530 that needs a special configuration for warm reset to work. @@ -16,6 +17,11 @@ The use of ti,twl4030-power-reset is recommended at least on When using ti,twl4030-power-idle, the TI recommended configuration for idle modes is loaded to the tlw4030 PMIC. +When using ti,twl4030-power-idle-osc-off, the TI recommended +configuration is used with the external oscillator being shut +down during off-idle. Note that this does not work on all boards +depending on how the external oscillator is wired. + Optional properties: - ti,use_poweroff: With this flag, the chip will initiates an ACTIVE-to-OFF or SLEEP-to-OFF transition when the system poweroffs. diff --git a/drivers/mfd/twl4030-power.c b/drivers/mfd/twl4030-power.c index 4846c7b48ebb..3bc969a5916b 100644 --- a/drivers/mfd/twl4030-power.c +++ b/drivers/mfd/twl4030-power.c @@ -761,6 +761,19 @@ static struct twl4030_power_data omap3_idle = { .resource_config = omap3_idle_rconfig, }; +/* Disable 32 KiHz oscillator during idle */ +static struct twl4030_resconfig osc_off_rconfig[] = { + TWL_REMAP_OFF(RES_CLKEN, DEV_GRP_P1 | DEV_GRP_P3, 3, 2), + { /* Terminator */ }, +}; + +static struct twl4030_power_data osc_off_idle = { + .scripts = omap3_idle_scripts, + .num = ARRAY_SIZE(omap3_idle_scripts), + .resource_config = omap3_idle_rconfig, + .board_config = osc_off_rconfig, +}; + static struct of_device_id twl4030_power_of_match[] = { { .compatible = "ti,twl4030-power-reset", @@ -770,6 +783,10 @@ static struct of_device_id twl4030_power_of_match[] = { .compatible = "ti,twl4030-power-idle", .data = &omap3_idle, }, + { + .compatible = "ti,twl4030-power-idle-osc-off", + .data = &osc_off_idle, + }, { }, }; MODULE_DEVICE_TABLE(of, twl4030_power_of_match); -- cgit v1.2.3