From 7d5929c1f34304ca5a970cfde8044053e56aa8c9 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 25 Aug 2014 16:15:32 -0700 Subject: mtd: nand: omap: Revert to using software ECC by default For v3.12 and prior, 1-bit Hamming code ECC via software was the default choice. Commit c66d039197e4 in v3.13 changed the behaviour to use 1-bit Hamming code via Hardware using a different ECC layout i.e. (ROM code layout) than what is used by software ECC. This ECC layout change causes NAND filesystems created in v3.12 and prior to be unusable in v3.13 and later. So revert back to using software ECC by default if an ECC scheme is not explicitely specified. This defect can be observed on the following boards during legacy boot -omap3beagle -omap3touchbook -overo -am3517crane -devkit8000 -ldp -3430sdp Signed-off-by: Roger Quadros Tested-by: Grazvydas Ignotas Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-flash.c | 2 +- arch/arm/mach-omap2/gpmc-nand.c | 3 ++- 2 files changed, 3 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/board-flash.c b/arch/arm/mach-omap2/board-flash.c index e87f2a83d6bf..2d245c2e641c 100644 --- a/arch/arm/mach-omap2/board-flash.c +++ b/arch/arm/mach-omap2/board-flash.c @@ -142,7 +142,7 @@ __init board_nand_init(struct mtd_partition *nand_parts, u8 nr_parts, u8 cs, board_nand_data.nr_parts = nr_parts; board_nand_data.devsize = nand_type; - board_nand_data.ecc_opt = OMAP_ECC_HAM1_CODE_HW; + board_nand_data.ecc_opt = OMAP_ECC_HAM1_CODE_SW; gpmc_nand_init(&board_nand_data, gpmc_t); } #endif /* CONFIG_MTD_NAND_OMAP2 || CONFIG_MTD_NAND_OMAP2_MODULE */ diff --git a/arch/arm/mach-omap2/gpmc-nand.c b/arch/arm/mach-omap2/gpmc-nand.c index 8897ad7035fd..cb7764314f17 100644 --- a/arch/arm/mach-omap2/gpmc-nand.c +++ b/arch/arm/mach-omap2/gpmc-nand.c @@ -49,7 +49,8 @@ static bool gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt) return 0; /* legacy platforms support only HAM1 (1-bit Hamming) ECC scheme */ - if (ecc_opt == OMAP_ECC_HAM1_CODE_HW) + if (ecc_opt == OMAP_ECC_HAM1_CODE_HW || + ecc_opt == OMAP_ECC_HAM1_CODE_SW) return 1; else return 0; -- cgit v1.2.3 From a3e83f05fbbf6c4994c658521a750bbd68bdf7a6 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 25 Aug 2014 16:15:33 -0700 Subject: ARM: OMAP2+: GPMC: Support Software ECC scheme via DT For v3.14 and prior, 1-bit Hamming code ECC via software was the default choice for some boards e.g. 3430sdp. Commit ac65caf514ec in v3.15 changed the behaviour to use 1-bit Hamming code via Hardware using a different ECC layout i.e. (ROM code layout) than what is used by software ECC. This ECC layout change causes NAND filesystems created in v3.14 and prior to be unusable in v3.15 and later. So don't mark "sw" scheme as deperecated and support it. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- Documentation/devicetree/bindings/mtd/gpmc-nand.txt | 2 +- arch/arm/mach-omap2/gpmc.c | 7 +++++-- 2 files changed, 6 insertions(+), 3 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index 65f4f7c43136..ee654e95d8ad 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -22,7 +22,7 @@ Optional properties: width of 8 is assumed. - ti,nand-ecc-opt: A string setting the ECC layout to use. One of: - "sw" use "ham1" instead + "sw" 1-bit Hamming ecc code via software "hw" use "ham1" instead "hw-romcode" use "ham1" instead "ham1" 1-bit Hamming ecc code diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index 8bc13380f0a0..9f42d5437fcc 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -1403,8 +1403,11 @@ static int gpmc_probe_nand_child(struct platform_device *pdev, pr_err("%s: ti,nand-ecc-opt not found\n", __func__); return -ENODEV; } - if (!strcmp(s, "ham1") || !strcmp(s, "sw") || - !strcmp(s, "hw") || !strcmp(s, "hw-romcode")) + + if (!strcmp(s, "sw")) + gpmc_nand_data->ecc_opt = OMAP_ECC_HAM1_CODE_SW; + else if (!strcmp(s, "ham1") || + !strcmp(s, "hw") || !strcmp(s, "hw-romcode")) gpmc_nand_data->ecc_opt = OMAP_ECC_HAM1_CODE_HW; else if (!strcmp(s, "bch4")) -- cgit v1.2.3 From 6953faf976c79a48b778a95319b8314419f7726b Mon Sep 17 00:00:00 2001 From: Hans Wennborg Date: Mon, 25 Aug 2014 16:15:34 -0700 Subject: ARM: OMAP: fix %d confusingly prefixed with 0x in format string Fix %d confusingly prefixed with 0x in format string. Signed-off-by: Hans Wennborg Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/id.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c index d42022f2a71e..53841dea80ea 100644 --- a/arch/arm/mach-omap2/id.c +++ b/arch/arm/mach-omap2/id.c @@ -663,7 +663,7 @@ void __init dra7xxx_check_revision(void) default: /* Unknown default to latest silicon rev as default*/ - pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%d)\n", + pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%x)\n", __func__, idcode, hawkeye, rev); omap_revision = DRA752_REV_ES1_1; } -- cgit v1.2.3 From 9a02ae4ed4ee139053d554ca1ab7d0e16609a0f5 Mon Sep 17 00:00:00 2001 From: Markus Pargmann Date: Mon, 25 Aug 2014 16:15:34 -0700 Subject: ARM: OMAP2+: omap_device: remove warning that clk alias already exists When an alias for a clock already exists the warning is printed. For every module with a main_clk defined, a clk alias for fck is added. There are some components that have the same main_clk defined, so this is a really normal situation. For example the am33xx edma device has 4 components using the same main clock. So there are three warnings in the boot log for this already existing clock alias: platform 49000000.edma: alias fck already exists platform 49000000.edma: alias fck already exists platform 49000000.edma: alias fck already exists As this is only interesting for developers, this patch changes the message to a debug message. Signed-off-by: Markus Pargmann Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/omap_device.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/omap_device.c b/arch/arm/mach-omap2/omap_device.c index 01ef59def44b..d22c30d3ccfa 100644 --- a/arch/arm/mach-omap2/omap_device.c +++ b/arch/arm/mach-omap2/omap_device.c @@ -56,7 +56,7 @@ static void _add_clkdev(struct omap_device *od, const char *clk_alias, r = clk_get_sys(dev_name(&od->pdev->dev), clk_alias); if (!IS_ERR(r)) { - dev_warn(&od->pdev->dev, + dev_dbg(&od->pdev->dev, "alias %s already exists\n", clk_alias); clk_put(r); return; -- cgit v1.2.3 From cc824534d4fef0e46e4486d5c1e10d3c6b1ebadc Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 25 Aug 2014 16:15:35 -0700 Subject: ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled Looks like MUSB cable removal can cause wake-up interrupts to stop working for device tree based booting at least for UART3 even as nothing is dynamically remuxed. This can be fixed by calling reconfigure_io_chain() for device tree based booting in hwmod code. Note that we already do that for legacy booting if the legacy mux is configured. My guess is that this is related to UART3 and MUSB ULPI hsusb0_data0 and hsusb0_data1 support for Carkit mode that somehow affect the configured IO chain for UART3 and require rearming the wake-up interrupts. In general, for device tree based booting, pinctrl-single calls the rearm hook that in turn calls reconfigure_io_chain so calling reconfigure_io_chain should not be needed from the hwmod code for other events. So let's limit the hwmod rearming of iochain only to HWMOD_FORCE_MSTANDBY where MUSB is currently the only user of it. If we see other devices needing similar changes we can add more checks for it. Cc: Paul Walmsley Cc: stable@vger.kernel.org # v3.16 Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/omap_hwmod.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c index 6c074f37cdd2..da1b256caccc 100644 --- a/arch/arm/mach-omap2/omap_hwmod.c +++ b/arch/arm/mach-omap2/omap_hwmod.c @@ -2185,6 +2185,8 @@ static int _enable(struct omap_hwmod *oh) oh->mux->pads_dynamic))) { omap_hwmod_mux(oh->mux, _HWMOD_STATE_ENABLED); _reconfigure_io_chain(); + } else if (oh->flags & HWMOD_FORCE_MSTANDBY) { + _reconfigure_io_chain(); } _add_initiator_dep(oh, mpu_oh); @@ -2291,6 +2293,8 @@ static int _idle(struct omap_hwmod *oh) if (oh->mux && oh->mux->pads_dynamic) { omap_hwmod_mux(oh->mux, _HWMOD_STATE_IDLE); _reconfigure_io_chain(); + } else if (oh->flags & HWMOD_FORCE_MSTANDBY) { + _reconfigure_io_chain(); } oh->_state = _HWMOD_STATE_IDLE; -- cgit v1.2.3 From af438fec6cb99fc2e2faf8b16b865af26ce722e6 Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Wed, 27 Aug 2014 19:38:22 -0600 Subject: ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants Use the corresponding compatibles to identify the devices. Signed-off-by: Rajendra Nayak Signed-off-by: Lokesh Vutla Acked-by: Nishanth Menon Tested-by: Nishanth Menon Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/soc.h | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/soc.h b/arch/arm/mach-omap2/soc.h index 01ca8086fb6c..4376f59626d1 100644 --- a/arch/arm/mach-omap2/soc.h +++ b/arch/arm/mach-omap2/soc.h @@ -245,6 +245,8 @@ IS_AM_SUBCLASS(437x, 0x437) #define soc_is_omap54xx() 0 #define soc_is_omap543x() 0 #define soc_is_dra7xx() 0 +#define soc_is_dra74x() 0 +#define soc_is_dra72x() 0 #if defined(MULTI_OMAP2) # if defined(CONFIG_ARCH_OMAP2) @@ -393,7 +395,11 @@ IS_OMAP_TYPE(3430, 0x3430) #if defined(CONFIG_SOC_DRA7XX) #undef soc_is_dra7xx +#undef soc_is_dra74x +#undef soc_is_dra72x #define soc_is_dra7xx() (of_machine_is_compatible("ti,dra7")) +#define soc_is_dra74x() (of_machine_is_compatible("ti,dra74")) +#define soc_is_dra72x() (of_machine_is_compatible("ti,dra72")) #endif /* Various silicon revisions for omap2 */ -- cgit v1.2.3 From f7f7a29bf0cf25af23f37e5b5bf1368b85705286 Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Wed, 27 Aug 2014 19:38:23 -0600 Subject: ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists To deal with IPs which are specific to dra74x and dra72x, maintain seperate ocp interface lists, while keeping the common list for all common IPs. Move USB OTG SS4 to dra74x only list since its unavailable in dra72x and is giving an abort during boot. The dra72x only list is empty for now and a placeholder for future hwmod additions which are specific to dra72x. Fixes: d904b38df0db13 ("ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss") Reported-by: Keerthy Signed-off-by: Rajendra Nayak Signed-off-by: Lokesh Vutla Tested-by: Nishanth Menon [paul@pwsan.com: fixed comment style to conform with CodingStyle] Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/omap_hwmod.c | 3 +++ arch/arm/mach-omap2/omap_hwmod_7xx_data.c | 22 ++++++++++++++++++++-- 2 files changed, 23 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c index 6c074f37cdd2..bc2466cc33b9 100644 --- a/arch/arm/mach-omap2/omap_hwmod.c +++ b/arch/arm/mach-omap2/omap_hwmod.c @@ -3345,6 +3345,9 @@ int __init omap_hwmod_register_links(struct omap_hwmod_ocp_if **ois) if (!ois) return 0; + if (ois[0] == NULL) /* Empty list */ + return 0; + if (!linkspace) { if (_alloc_linkspace(ois)) { pr_err("omap_hwmod: could not allocate link space\n"); diff --git a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c index 2757abf87fbc..5684f112654b 100644 --- a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c @@ -35,6 +35,7 @@ #include "i2c.h" #include "mmc.h" #include "wd_timer.h" +#include "soc.h" /* Base offset for all DRA7XX interrupts external to MPUSS */ #define DRA7XX_IRQ_GIC_START 32 @@ -3261,7 +3262,6 @@ static struct omap_hwmod_ocp_if *dra7xx_hwmod_ocp_ifs[] __initdata = { &dra7xx_l4_per3__usb_otg_ss1, &dra7xx_l4_per3__usb_otg_ss2, &dra7xx_l4_per3__usb_otg_ss3, - &dra7xx_l4_per3__usb_otg_ss4, &dra7xx_l3_main_1__vcp1, &dra7xx_l4_per2__vcp1, &dra7xx_l3_main_1__vcp2, @@ -3270,8 +3270,26 @@ static struct omap_hwmod_ocp_if *dra7xx_hwmod_ocp_ifs[] __initdata = { NULL, }; +static struct omap_hwmod_ocp_if *dra74x_hwmod_ocp_ifs[] __initdata = { + &dra7xx_l4_per3__usb_otg_ss4, + NULL, +}; + +static struct omap_hwmod_ocp_if *dra72x_hwmod_ocp_ifs[] __initdata = { + NULL, +}; + int __init dra7xx_hwmod_init(void) { + int ret; + omap_hwmod_init(); - return omap_hwmod_register_links(dra7xx_hwmod_ocp_ifs); + ret = omap_hwmod_register_links(dra7xx_hwmod_ocp_ifs); + + if (!ret && soc_is_dra74x()) + return omap_hwmod_register_links(dra74x_hwmod_ocp_ifs); + else if (!ret && soc_is_dra72x()) + return omap_hwmod_register_links(dra72x_hwmod_ocp_ifs); + + return ret; } -- cgit v1.2.3 From 2b54057c9b2638792bdd83b58bad7a0cdf5f4533 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 2 Sep 2014 16:57:06 +0300 Subject: ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring For NAND read & write wait pin monitoring must be kept disabled as the wait pin is only used to indicate NAND device ready status and not to extend each read/write cycle. So don't print a warning if wait pin is specified while read/write monitoring is not in the device tree. Sanity check wait pin number irrespective if read/write monitoring is set or not. Signed-off-by: Roger Quadros Reviewed-by: Pekon Gupta Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/gpmc.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index 9f42d5437fcc..2f97228f188a 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -1207,8 +1207,7 @@ int gpmc_cs_program_settings(int cs, struct gpmc_settings *p) } } - if ((p->wait_on_read || p->wait_on_write) && - (p->wait_pin > gpmc_nr_waitpins)) { + if (p->wait_pin > gpmc_nr_waitpins) { pr_err("%s: invalid wait-pin (%d)\n", __func__, p->wait_pin); return -EINVAL; } @@ -1288,8 +1287,8 @@ void gpmc_read_settings_dt(struct device_node *np, struct gpmc_settings *p) p->wait_on_write = of_property_read_bool(np, "gpmc,wait-on-write"); if (!p->wait_on_read && !p->wait_on_write) - pr_warn("%s: read/write wait monitoring not enabled!\n", - __func__); + pr_debug("%s: rd/wr wait monitoring not enabled!\n", + __func__); } } -- cgit v1.2.3