From fdcad71cef68529a1f54331f533763ca53814f96 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Tue, 20 Oct 2009 16:32:53 +0200 Subject: at91: at91sam9g20ek modify dual slot evaluation kit at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the previous dual slot board definition to match the official rev. C board. It also allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one. Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC slot A. This lead to a modification of those definitions. Signed-off-by: Nicolas Ferre Acked-by: Andrew Victor --- arch/arm/mach-at91/Kconfig | 20 +++++++++++--------- 1 file changed, 11 insertions(+), 9 deletions(-) (limited to 'arch/arm/mach-at91/Kconfig') diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index e35d54d43e70..2fd88437348b 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -289,13 +289,6 @@ config MACH_NEOCORE926 help Select this if you are using the Adeneo Neocore 926 board. -config MACH_AT91SAM9G20EK_2MMC - bool "Atmel AT91SAM9G20-EK Evaluation Kit modified for 2 MMC Slots" - depends on ARCH_AT91SAM9G20 - help - Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit - Rev A or B modified for 2 MMC Slots. - endif # ---------------------------------------------------------- @@ -322,7 +315,16 @@ config MACH_AT91SAM9G20EK bool "Atmel AT91SAM9G20-EK Evaluation Kit" depends on ARCH_AT91SAM9G20 help - Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit. + Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit + that embeds only one SD/MMC slot. + +config MACH_AT91SAM9G20EK_2MMC + bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots" + depends on ARCH_AT91SAM9G20 + help + Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit + with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and + onwards. config MACH_CPU9G20 bool "Eukrea CPU9G20 board" @@ -392,7 +394,7 @@ config MTD_AT91_DATAFLASH_CARD config MTD_NAND_ATMEL_BUSWIDTH_16 bool "Enable 16-bit data bus interface to NAND flash" - depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK) + depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G20EK_2MMC || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK) help On AT91SAM926x boards both types of NAND flash can be present (8 and 16 bit data bus width). -- cgit v1.2.3 From c4e4ab9f23d26498a01316428d710833fb96f214 Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Thu, 22 Oct 2009 18:41:41 +0200 Subject: at91: remove not needed depends on Those "depends on" are a double check as all machine entries are surrounded by "if " conditions. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD Signed-off-by: Nicolas Ferre Acked-by: Andrew Victor --- arch/arm/mach-at91/Kconfig | 32 -------------------------------- 1 file changed, 32 deletions(-) (limited to 'arch/arm/mach-at91/Kconfig') diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 2fd88437348b..4301c6bad80c 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -76,89 +76,76 @@ comment "AT91RM9200 Board Type" config MACH_ONEARM bool "Ajeco 1ARM Single Board Computer" - depends on ARCH_AT91RM9200 help Select this if you are using Ajeco's 1ARM Single Board Computer. config ARCH_AT91RM9200DK bool "Atmel AT91RM9200-DK Development board" - depends on ARCH_AT91RM9200 help Select this if you are using Atmel's AT91RM9200-DK Development board. (Discontinued) config MACH_AT91RM9200EK bool "Atmel AT91RM9200-EK Evaluation Kit" - depends on ARCH_AT91RM9200 help Select this if you are using Atmel's AT91RM9200-EK Evaluation Kit. config MACH_CSB337 bool "Cogent CSB337" - depends on ARCH_AT91RM9200 help Select this if you are using Cogent's CSB337 board. config MACH_CSB637 bool "Cogent CSB637" - depends on ARCH_AT91RM9200 help Select this if you are using Cogent's CSB637 board. config MACH_CARMEVA bool "Conitec ARM&EVA" - depends on ARCH_AT91RM9200 help Select this if you are using Conitec's AT91RM9200-MCU-Module. config MACH_ATEB9200 bool "Embest ATEB9200" - depends on ARCH_AT91RM9200 help Select this if you are using Embest's ATEB9200 board. config MACH_KB9200 bool "KwikByte KB920x" - depends on ARCH_AT91RM9200 help Select this if you are using KwikByte's KB920x board. config MACH_PICOTUX2XX bool "picotux 200" - depends on ARCH_AT91RM9200 help Select this if you are using a picotux 200. config MACH_KAFA bool "Sperry-Sun KAFA board" - depends on ARCH_AT91RM9200 help Select this if you are using Sperry-Sun's KAFA board. config MACH_ECBAT91 bool "emQbit ECB_AT91 SBC" - depends on ARCH_AT91RM9200 help Select this if you are using emQbit's ECB_AT91 board. config MACH_YL9200 bool "ucDragon YL-9200" - depends on ARCH_AT91RM9200 help Select this if you are using the ucDragon YL-9200 board. config MACH_CPUAT91 bool "Eukrea CPUAT91" - depends on ARCH_AT91RM9200 help Select this if you are using the Eukrea Electromatique's CPUAT91 board . @@ -173,7 +160,6 @@ comment "AT91SAM9260 Variants" config ARCH_AT91SAM9260_SAM9XE bool "AT91SAM9XE" - depends on ARCH_AT91SAM9260 help Select this if you are using Atmel's AT91SAM9XE System-on-Chip. They are basically AT91SAM9260s with various sizes of embedded Flash. @@ -182,28 +168,24 @@ comment "AT91SAM9260 / AT91SAM9XE Board Type" config MACH_AT91SAM9260EK bool "Atmel AT91SAM9260-EK / AT91SAM9XE Evaluation Kit" - depends on ARCH_AT91SAM9260 help Select this if you are using Atmel's AT91SAM9260-EK or AT91SAM9XE Evaluation Kit config MACH_CAM60 bool "KwikByte KB9260 (CAM60) board" - depends on ARCH_AT91SAM9260 help Select this if you are using KwikByte's KB9260 (CAM60) board based on the Atmel AT91SAM9260. config MACH_SAM9_L9260 bool "Olimex SAM9-L9260 board" - depends on ARCH_AT91SAM9260 help Select this if you are using Olimex's SAM9-L9260 board based on the Atmel AT91SAM9260. config MACH_AFEB9260 bool "Custom afeb9260 board v1" - depends on ARCH_AT91SAM9260 help Select this if you are using custom afeb9260 board based on open hardware design. Select this for revision 1 of the board. @@ -212,21 +194,18 @@ config MACH_AFEB9260 config MACH_USB_A9260 bool "CALAO USB-A9260" - depends on ARCH_AT91SAM9260 help Select this if you are using a Calao Systems USB-A9260. config MACH_QIL_A9260 bool "CALAO QIL-A9260 board" - depends on ARCH_AT91SAM9260 help Select this if you are using a Calao Systems QIL-A9260 Board. config MACH_CPU9260 bool "Eukrea CPU9260 board" - depends on ARCH_AT91SAM9260 help Select this if you are using a Eukrea Electromatique's CPU9260 Board @@ -241,7 +220,6 @@ comment "AT91SAM9261 Board Type" config MACH_AT91SAM9261EK bool "Atmel AT91SAM9261-EK Evaluation Kit" - depends on ARCH_AT91SAM9261 help Select this if you are using Atmel's AT91SAM9261-EK Evaluation Kit. @@ -256,7 +234,6 @@ comment "AT91SAM9G10 Board Type" config MACH_AT91SAM9G10EK bool "Atmel AT91SAM9G10-EK Evaluation Kit" - depends on ARCH_AT91SAM9G10 help Select this if you are using Atmel's AT91SAM9G10-EK Evaluation Kit. @@ -271,21 +248,18 @@ comment "AT91SAM9263 Board Type" config MACH_AT91SAM9263EK bool "Atmel AT91SAM9263-EK Evaluation Kit" - depends on ARCH_AT91SAM9263 help Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit. config MACH_USB_A9263 bool "CALAO USB-A9263" - depends on ARCH_AT91SAM9263 help Select this if you are using a Calao Systems USB-A9263. config MACH_NEOCORE926 bool "Adeneo NEOCORE926" - depends on ARCH_AT91SAM9263 help Select this if you are using the Adeneo Neocore 926 board. @@ -299,7 +273,6 @@ comment "AT91SAM9RL Board Type" config MACH_AT91SAM9RLEK bool "Atmel AT91SAM9RL-EK Evaluation Kit" - depends on ARCH_AT91SAM9RL help Select this if you are using Atmel's AT91SAM9RL-EK Evaluation Kit. @@ -313,14 +286,12 @@ comment "AT91SAM9G20 Board Type" config MACH_AT91SAM9G20EK bool "Atmel AT91SAM9G20-EK Evaluation Kit" - depends on ARCH_AT91SAM9G20 help Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit that embeds only one SD/MMC slot. config MACH_AT91SAM9G20EK_2MMC bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots" - depends on ARCH_AT91SAM9G20 help Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and @@ -328,7 +299,6 @@ config MACH_AT91SAM9G20EK_2MMC config MACH_CPU9G20 bool "Eukrea CPU9G20 board" - depends on ARCH_AT91SAM9G20 help Select this if you are using a Eukrea Electromatique's CPU9G20 Board @@ -343,7 +313,6 @@ comment "AT91SAM9G45 Board Type" config MACH_AT91SAM9G45EKES bool "Atmel AT91SAM9G45-EKES Evaluation Kit" - depends on ARCH_AT91SAM9G45 help Select this if you are using Atmel's AT91SAM9G45-EKES Evaluation Kit. "ES" at the end of the name means that this board is an @@ -359,7 +328,6 @@ comment "AT91CAP9 Board Type" config MACH_AT91CAP9ADK bool "Atmel AT91CAP9A-DK Evaluation Kit" - depends on ARCH_AT91CAP9 help Select this if you are using Atmel's AT91CAP9A-DK Evaluation Kit. -- cgit v1.2.3 From 2ef9f59a7a3a0894be63836542f0902a45ffdd22 Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Thu, 22 Oct 2009 18:50:26 +0200 Subject: at91: Kconfig simplification Instead of adding "depends on" at config level, introduce HAVE_* config variables. Add them at machine or soc level to specify the ability of a particular support. It will ease new board introduction and readability. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD Signed-off-by: Nicolas Ferre Acked-by: Andrew Victor --- arch/arm/mach-at91/Kconfig | 53 +++++++++++++++++++++++++++++++++++++++++----- 1 file changed, 48 insertions(+), 5 deletions(-) (limited to 'arch/arm/mach-at91/Kconfig') diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 4301c6bad80c..bb4cd27c322f 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -1,5 +1,20 @@ if ARCH_AT91 +config HAVE_AT91_DATAFLASH_CARD + bool + +config HAVE_NAND_ATMEL_BUSWIDTH_16 + bool + +config HAVE_AT91_USART3 + bool + +config HAVE_AT91_USART4 + bool + +config HAVE_AT91_USART5 + bool + menu "Atmel AT91 System-on-Chip" choice @@ -10,12 +25,16 @@ config ARCH_AT91RM9200 select CPU_ARM920T select GENERIC_TIME select GENERIC_CLOCKEVENTS + select HAVE_AT91_USART3 config ARCH_AT91SAM9260 bool "AT91SAM9260 or AT91SAM9XE" select CPU_ARM926T select GENERIC_TIME select GENERIC_CLOCKEVENTS + select HAVE_AT91_USART3 + select HAVE_AT91_USART4 + select HAVE_AT91_USART5 config ARCH_AT91SAM9261 bool "AT91SAM9261" @@ -40,18 +59,23 @@ config ARCH_AT91SAM9RL select CPU_ARM926T select GENERIC_TIME select GENERIC_CLOCKEVENTS + select HAVE_AT91_USART3 config ARCH_AT91SAM9G20 bool "AT91SAM9G20" select CPU_ARM926T select GENERIC_TIME select GENERIC_CLOCKEVENTS + select HAVE_AT91_USART3 + select HAVE_AT91_USART4 + select HAVE_AT91_USART5 config ARCH_AT91SAM9G45 bool "AT91SAM9G45" select CPU_ARM926T select GENERIC_TIME select GENERIC_CLOCKEVENTS + select HAVE_AT91_USART3 config ARCH_AT91CAP9 bool "AT91CAP9" @@ -82,12 +106,14 @@ config MACH_ONEARM config ARCH_AT91RM9200DK bool "Atmel AT91RM9200-DK Development board" + select HAVE_AT91_DATAFLASH_CARD help Select this if you are using Atmel's AT91RM9200-DK Development board. (Discontinued) config MACH_AT91RM9200EK bool "Atmel AT91RM9200-EK Evaluation Kit" + select HAVE_AT91_DATAFLASH_CARD help Select this if you are using Atmel's AT91RM9200-EK Evaluation Kit. @@ -135,6 +161,7 @@ config MACH_KAFA config MACH_ECBAT91 bool "emQbit ECB_AT91 SBC" + select HAVE_AT91_DATAFLASH_CARD help Select this if you are using emQbit's ECB_AT91 board. @@ -168,6 +195,8 @@ comment "AT91SAM9260 / AT91SAM9XE Board Type" config MACH_AT91SAM9260EK bool "Atmel AT91SAM9260-EK / AT91SAM9XE Evaluation Kit" + select HAVE_AT91_DATAFLASH_CARD + select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9260-EK or AT91SAM9XE Evaluation Kit @@ -180,6 +209,7 @@ config MACH_CAM60 config MACH_SAM9_L9260 bool "Olimex SAM9-L9260 board" + select HAVE_AT91_DATAFLASH_CARD help Select this if you are using Olimex's SAM9-L9260 board based on the Atmel AT91SAM9260. @@ -220,6 +250,8 @@ comment "AT91SAM9261 Board Type" config MACH_AT91SAM9261EK bool "Atmel AT91SAM9261-EK Evaluation Kit" + select HAVE_AT91_DATAFLASH_CARD + select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9261-EK Evaluation Kit. @@ -234,6 +266,8 @@ comment "AT91SAM9G10 Board Type" config MACH_AT91SAM9G10EK bool "Atmel AT91SAM9G10-EK Evaluation Kit" + select HAVE_AT91_DATAFLASH_CARD + select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9G10-EK Evaluation Kit. @@ -248,6 +282,8 @@ comment "AT91SAM9263 Board Type" config MACH_AT91SAM9263EK bool "Atmel AT91SAM9263-EK Evaluation Kit" + select HAVE_AT91_DATAFLASH_CARD + select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit. @@ -260,6 +296,7 @@ config MACH_USB_A9263 config MACH_NEOCORE926 bool "Adeneo NEOCORE926" + select HAVE_AT91_DATAFLASH_CARD help Select this if you are using the Adeneo Neocore 926 board. @@ -286,12 +323,15 @@ comment "AT91SAM9G20 Board Type" config MACH_AT91SAM9G20EK bool "Atmel AT91SAM9G20-EK Evaluation Kit" + select HAVE_AT91_DATAFLASH_CARD + select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit that embeds only one SD/MMC slot. config MACH_AT91SAM9G20EK_2MMC bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots" + select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and @@ -313,6 +353,7 @@ comment "AT91SAM9G45 Board Type" config MACH_AT91SAM9G45EKES bool "Atmel AT91SAM9G45-EKES Evaluation Kit" + select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9G45-EKES Evaluation Kit. "ES" at the end of the name means that this board is an @@ -328,6 +369,8 @@ comment "AT91CAP9 Board Type" config MACH_AT91CAP9ADK bool "Atmel AT91CAP9A-DK Evaluation Kit" + select HAVE_AT91_DATAFLASH_CARD + select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91CAP9A-DK Evaluation Kit. @@ -356,13 +399,13 @@ comment "AT91 Board Options" config MTD_AT91_DATAFLASH_CARD bool "Enable DataFlash Card support" - depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_ECBAT91 || MACH_SAM9_L9260 || MACH_AT91CAP9ADK || MACH_NEOCORE926) + depends on HAVE_AT91_DATAFLASH_CARD help Enable support for the DataFlash card. config MTD_NAND_ATMEL_BUSWIDTH_16 bool "Enable 16-bit data bus interface to NAND flash" - depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G20EK_2MMC || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK) + depends on HAVE_NAND_ATMEL_BUSWIDTH_16 help On AT91SAM926x boards both types of NAND flash can be present (8 and 16 bit data bus width). @@ -424,15 +467,15 @@ config AT91_EARLY_USART2 config AT91_EARLY_USART3 bool "USART3" - depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260 || ARCH_AT91SAM9G20 || ARCH_AT91SAM9G45) + depends on HAVE_AT91_USART3 config AT91_EARLY_USART4 bool "USART4" - depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20 + depends on HAVE_AT91_USART4 config AT91_EARLY_USART5 bool "USART5" - depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20 + depends on HAVE_AT91_USART5 endchoice -- cgit v1.2.3 From 0912e5359f89f303f53fd4874dadab77a4949a8a Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Tue, 23 Jun 2009 16:30:56 +0200 Subject: atmel_lcdfb Kconfig: remove long dependency line Many Atmel SOC are embedding a LCD controller. This patch removes the long dependency line for this Atmel LCD framebuffer driver configuration entry. The HAVE_FB_ATMEL configuration option is located in the video Kconfig file as it may be setup by ARM/AT91 and AVR32 chips. Signed-off-by: Nicolas Ferre Acked-by: Jean-Christophe PLAGNIOL-VILLARD Acked-by: Andrew Victor --- arch/arm/mach-at91/Kconfig | 6 ++++++ arch/avr32/Kconfig | 1 + drivers/video/Kconfig | 5 ++++- 3 files changed, 11 insertions(+), 1 deletion(-) (limited to 'arch/arm/mach-at91/Kconfig') diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index bb4cd27c322f..3df124e54267 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -41,18 +41,21 @@ config ARCH_AT91SAM9261 select CPU_ARM926T select GENERIC_TIME select GENERIC_CLOCKEVENTS + select HAVE_FB_ATMEL config ARCH_AT91SAM9G10 bool "AT91SAM9G10" select CPU_ARM926T select GENERIC_TIME select GENERIC_CLOCKEVENTS + select HAVE_FB_ATMEL config ARCH_AT91SAM9263 bool "AT91SAM9263" select CPU_ARM926T select GENERIC_TIME select GENERIC_CLOCKEVENTS + select HAVE_FB_ATMEL config ARCH_AT91SAM9RL bool "AT91SAM9RL" @@ -60,6 +63,7 @@ config ARCH_AT91SAM9RL select GENERIC_TIME select GENERIC_CLOCKEVENTS select HAVE_AT91_USART3 + select HAVE_FB_ATMEL config ARCH_AT91SAM9G20 bool "AT91SAM9G20" @@ -76,12 +80,14 @@ config ARCH_AT91SAM9G45 select GENERIC_TIME select GENERIC_CLOCKEVENTS select HAVE_AT91_USART3 + select HAVE_FB_ATMEL config ARCH_AT91CAP9 bool "AT91CAP9" select CPU_ARM926T select GENERIC_TIME select GENERIC_CLOCKEVENTS + select HAVE_FB_ATMEL config ARCH_AT91X40 bool "AT91x40" diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig index 35e3bd9858df..d856354f4272 100644 --- a/arch/avr32/Kconfig +++ b/arch/avr32/Kconfig @@ -92,6 +92,7 @@ config PLATFORM_AT32AP select PERFORMANCE_COUNTERS select ARCH_REQUIRE_GPIOLIB select GENERIC_ALLOCATOR + select HAVE_FB_ATMEL # # CPU types diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig index 188e1ba3b69f..6b89eb55ed32 100644 --- a/drivers/video/Kconfig +++ b/drivers/video/Kconfig @@ -5,6 +5,9 @@ menu "Graphics support" depends on HAS_IOMEM +config HAVE_FB_ATMEL + bool + source "drivers/char/agp/Kconfig" source "drivers/gpu/vga/Kconfig" @@ -937,7 +940,7 @@ config FB_S1D13XXX config FB_ATMEL tristate "AT91/AT32 LCD Controller support" - depends on FB && (ARCH_AT91SAM9261 || ARCH_AT91SAM9G10 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45 || ARCH_AT91CAP9 || AVR32) + depends on FB && HAVE_FB_ATMEL select FB_CFB_FILLRECT select FB_CFB_COPYAREA select FB_CFB_IMAGEBLIT -- cgit v1.2.3