From 3e75b76f0f17194e0e65694ade6e69fc11593190 Mon Sep 17 00:00:00 2001 From: Guillaume La Roque Date: Tue, 14 May 2019 10:26:47 +0200 Subject: dt-bindings: pinctrl: add a 'drive-strength-microamp' property This property allow drive-strength parameter in uA instead of mA. Signed-off-by: Guillaume La Roque Acked-by: Martin Blumenstingl Reviewed-by: Martin Blumenstingl Reviewed-by: Rob Herring Signed-off-by: Linus Walleij --- Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt | 3 +++ 1 file changed, 3 insertions(+) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index cef2b5855d60..fcd37e93ed4d 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -258,6 +258,7 @@ drive-push-pull - drive actively high and low drive-open-drain - drive with open drain drive-open-source - drive with open source drive-strength - sink or source at most X mA +drive-strength-microamp - sink or source at most X uA input-enable - enable input on pin (no effect on output, such as enabling an input buffer) input-disable - disable input on pin (no effect on output, such as @@ -326,6 +327,8 @@ arguments are described below. - drive-strength takes as argument the target strength in mA. +- drive-strength-microamp takes as argument the target strength in uA. + - input-debounce takes the debounce time in usec as argument or 0 to disable debouncing -- cgit v1.2.3 From 013786c043298710887e983ac8d59aaff1f554f3 Mon Sep 17 00:00:00 2001 From: Guillaume La Roque Date: Tue, 14 May 2019 10:26:49 +0200 Subject: dt-bindings: pinctrl: meson: Add drive-strength-microamp property Add optional drive-strength-microamp property Signed-off-by: Guillaume La Roque Reviewed-by: Martin Blumenstingl Reviewed-by: Rob Herring Signed-off-by: Linus Walleij --- Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index a47dd990a8d3..a7618605bf1e 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -51,6 +51,10 @@ Configuration nodes support the generic properties "bias-disable", "bias-pull-up" and "bias-pull-down", described in file pinctrl-bindings.txt +Optional properties : + - drive-strength-microamp: Drive strength for the specified pins in uA. + This property is only valid for G12A and newer. + === Example === pinctrl: pinctrl@c1109880 { -- cgit v1.2.3 From f3fbedabb7be0d19b2da862fa6c01d82ac39c716 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Thu, 9 May 2019 13:59:53 -0700 Subject: dt-bindings: pinctrl: bcm2835-gpio: Document BCM7211 compatible BCM7211 has a slightly different block layout and some additional GPIO registers that were added, document the compatible string. Signed-off-by: Florian Fainelli Reviewed-by: Eric Anholt Signed-off-by: Linus Walleij --- Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt | 3 +++ 1 file changed, 3 insertions(+) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt index 3fac0a061bcc..ac6d614d74e0 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt @@ -5,6 +5,9 @@ controller, and pinmux/control device. Required properties: - compatible: "brcm,bcm2835-gpio" +- compatible: should be one of: + "brcm,bcm2835-gpio" - BCM2835 compatible pinctrl + "brcm,bcm7211-gpio" - BCM7211 compatible pinctrl - reg: Should contain the physical address of the GPIO module's registers. - gpio-controller: Marks the device node as a GPIO controller. - #gpio-cells : Should be two. The first cell is the pin number and the -- cgit v1.2.3 From 2c9239c125f0c657d2955780f364168d4c15aa8b Mon Sep 17 00:00:00 2001 From: Alexandre Torgue Date: Fri, 10 May 2019 17:45:26 +0200 Subject: dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema Convert the STM32 pinctrl binding to DT schema format using json-schema. Signed-off-by: Alexandre Torgue Reviewed-by: Rob Herring Signed-off-by: Linus Walleij --- .../bindings/pinctrl/st,stm32-pinctrl.txt | 208 ---------------- .../bindings/pinctrl/st,stm32-pinctrl.yaml | 264 +++++++++++++++++++++ 2 files changed, 264 insertions(+), 208 deletions(-) delete mode 100644 Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt deleted file mode 100644 index 00169255e48c..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ /dev/null @@ -1,208 +0,0 @@ -* STM32 GPIO and Pin Mux/Config controller - -STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware -controller. It controls the input/output settings on the available pins and -also provides ability to multiplex and configure the output of various on-chip -controllers onto these pads. - -Pin controller node: -Required properies: - - compatible: value should be one of the following: - "st,stm32f429-pinctrl" - "st,stm32f469-pinctrl" - "st,stm32f746-pinctrl" - "st,stm32f769-pinctrl" - "st,stm32h743-pinctrl" - "st,stm32mp157-pinctrl" - "st,stm32mp157-z-pinctrl" - - #address-cells: The value of this property must be 1 - - #size-cells : The value of this property must be 1 - - ranges : defines mapping between pin controller node (parent) to - gpio-bank node (children). - - pins-are-numbered: Specify the subnodes are using numbered pinmux to - specify pins. - -GPIO controller/bank node: -Required properties: - - gpio-controller : Indicates this device is a GPIO controller - - #gpio-cells : Should be two. - The first cell is the pin number - The second one is the polarity: - - 0 for active high - - 1 for active low - - reg : The gpio address range, relative to the pinctrl range - - clocks : clock that drives this bank - - st,bank-name : Should be a name string for this bank as specified in - the datasheet - -Optional properties: - - reset: : Reference to the reset controller - - st,syscfg: Should be phandle/offset/mask. - -The phandle to the syscon node which includes IRQ mux selection register. - -The offset of the IRQ mux selection register - -The field mask of IRQ mux, needed if different of 0xf. - - gpio-ranges: Define a dedicated mapping between a pin-controller and - a gpio controller. Format is <&phandle a b c> with: - -(phandle): phandle of pin-controller. - -(a): gpio base offset in range. - -(b): pin base offset in range. - -(c): gpio count in range - This entry has to be used either if there are holes inside a bank: - GPIOB0/B1/B2/B14/B15 (see example 2) - or if banks are not contiguous: - GPIOA/B/C/E... - NOTE: If "gpio-ranges" is used for a gpio controller, all gpio-controller - have to use a "gpio-ranges" entry. - More details in Documentation/devicetree/bindings/gpio/gpio.txt. - - st,bank-ioport: should correspond to the EXTI IOport selection (EXTI line - used to select GPIOs as interrupts). - - hwlocks: reference to a phandle of a hardware spinlock provider node. - - st,package: Indicates the SOC package used. - More details in include/dt-bindings/pinctrl/stm32-pinfunc.h - -Example 1: -#include -... - - pin-controller { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,stm32f429-pinctrl"; - ranges = <0 0x40020000 0x3000>; - pins-are-numbered; - - gpioa: gpio@40020000 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x0 0x400>; - resets = <&reset_ahb1 0>; - st,bank-name = "GPIOA"; - }; - ... - pin-functions nodes follow... - }; - -Example 2: -#include -... - - pinctrl: pin-controller { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,stm32f429-pinctrl"; - ranges = <0 0x40020000 0x3000>; - pins-are-numbered; - - gpioa: gpio@40020000 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x0 0x400>; - resets = <&reset_ahb1 0>; - st,bank-name = "GPIOA"; - gpio-ranges = <&pinctrl 0 0 16>; - }; - - gpiob: gpio@40020400 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x0 0x400>; - resets = <&reset_ahb1 0>; - st,bank-name = "GPIOB"; - ngpios = 4; - gpio-ranges = <&pinctrl 0 16 3>, - <&pinctrl 14 30 2>; - }; - - - ... - pin-functions nodes follow... - }; - - -Contents of function subnode node: ----------------------------------- -Subnode format -A pinctrl node should contain at least one subnode representing the -pinctrl group available on the machine. Each subnode will list the -pins it needs, and how they should be configured, with regard to muxer -configuration, pullups, drive, output high/low and output speed. - - node { - pinmux = ; - GENERIC_PINCONFIG; - }; - -Required properties: -- pinmux: integer array, represents gpio pin number and mux setting. - Supported pin number and mux varies for different SoCs, and are defined in - dt-bindings/pinctrl/-pinfunc.h directly. - These defines are calculated as: - ((port * 16 + line) << 8) | function - With: - - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11) - - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15) - - function: The function number, can be: - * 0 : GPIO - * 1 : Alternate Function 0 - * 2 : Alternate Function 1 - * 3 : Alternate Function 2 - * ... - * 16 : Alternate Function 15 - * 17 : Analog - - To simplify the usage, macro is available to generate "pinmux" field. - This macro is available here: - - include/dt-bindings/pinctrl/stm32-pinfunc.h - - Some examples of using macro: - /* GPIO A9 set as alernate function 2 */ - ... { - pinmux = ; - }; - /* GPIO A9 set as GPIO */ - ... { - pinmux = ; - }; - /* GPIO A9 set as analog */ - ... { - pinmux = ; - }; - -Optional properties: -- GENERIC_PINCONFIG: is the generic pinconfig options to use. - Available options are: - - bias-disable, - - bias-pull-down, - - bias-pull-up, - - drive-push-pull, - - drive-open-drain, - - output-low - - output-high - - slew-rate = , with x being: - < 0 > : Low speed - < 1 > : Medium speed - < 2 > : Fast speed - < 3 > : High speed - -Example: - -pin-controller { -... - usart1_pins_a: usart1@0 { - pins1 { - pinmux = ; - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins2 { - pinmux = ; - bias-disable; - }; - }; -}; - -&usart1 { - pinctrl-0 = <&usart1_pins_a>; - pinctrl-names = "default"; -}; diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml new file mode 100644 index 000000000000..06c4b66c3ee6 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml @@ -0,0 +1,264 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (C) STMicroelectronics 2019. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/st,stm32-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STM32 GPIO and Pin Mux/Config controller + +maintainers: + - Alexandre TORGUE + +description: | + STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware + controller. It controls the input/output settings on the available pins and + also provides ability to multiplex and configure the output of various + on-chip controllers onto these pads. + +properties: + compatible: + enum: + - st,stm32f429-pinctrl + - st,stm32f469-pinctrl + - st,stm32f746-pinctrl + - st,stm32f769-pinctrl + - st,stm32h743-pinctrl + - st,stm32mp157-pinctrl + - st,stm32mp157-z-pinctrl + + '#address-cells': + const: 1 + '#size-cells': + const: 1 + + ranges: true + pins-are-numbered: true + hwlocks: true + + st,syscfg: + $ref: "/schemas/types.yaml#/definitions/phandle-array" + description: Should be phandle/offset/mask + items: + - description: Phandle to the syscon node which includes IRQ mux selection. + - description: The offset of the IRQ mux selection register. + - description: The field mask of IRQ mux, needed if different of 0xf. + + st,package: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [1, 2, 4, 8] + description: + Indicates the SOC package used. + More details in include/dt-bindings/pinctrl/stm32-pinfunc.h + + +patternProperties: + '^gpio@[0-9a-f]*$': + properties: + gpio-controller: true + '#gpio-cells': + const: 2 + + reg: + maxItems: 1 + clocks: + maxItems: 1 + reset: + minItems: 1 + maxItems: 1 + gpio-ranges: + minItems: 1 + maxItems: 16 + ngpios: + description: + Number of available gpios in a bank. + minimum: 1 + maximum: 16 + + st,bank-name: + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: + - GPIOA + - GPIOB + - GPIOC + - GPIOD + - GPIOE + - GPIOF + - GPIOG + - GPIOH + - GPIOI + - GPIOJ + - GPIOK + - GPIOZ + description: + Should be a name string for this bank as specified in the datasheet. + + st,bank-ioport: + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - minimum: 0 + - maximum: 11 + + description: + Should correspond to the EXTI IOport selection (EXTI line used + to select GPIOs as interrupts). + + required: + - gpio-controller + - '#gpio-cells' + - reg + - clocks + - st,bank-name + + '-[0-9]*$': + patternProperties: + '^pins': + description: | + A pinctrl node should contain at least one subnode representing the + pinctrl group available on the machine. Each subnode will list the + pins it needs, and how they should be configured, with regard to muxer + configuration, pullups, drive, output high/low and output speed. + properties: + pinmux: + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32-array" + description: | + Integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are + defined in dt-bindings/pinctrl/-pinfunc.h directly. + These defines are calculated as: ((port * 16 + line) << 8) | function + With: + - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11) + - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15) + - function: The function number, can be: + * 0 : GPIO + * 1 : Alternate Function 0 + * 2 : Alternate Function 1 + * 3 : Alternate Function 2 + * ... + * 16 : Alternate Function 15 + * 17 : Analog + To simplify the usage, macro is available to generate "pinmux" field. + This macro is available here: + - include/dt-bindings/pinctrl/stm32-pinfunc.h + Some examples of using macro: + /* GPIO A9 set as alernate function 2 */ + ... { + pinmux = ; + }; + /* GPIO A9 set as GPIO */ + ... { + pinmux = ; + }; + /* GPIO A9 set as analog */ + ... { + pinmux = ; + }; + + bias-disable: + type: boolean + bias-pull-down: + type: boolean + bias-pull-up: + type: boolean + drive-push-pull: + type: boolean + drive-open-drain: + type: boolean + output-low: + type: boolean + output-high: + type: boolean + slew-rate: + description: | + 0: Low speed + 1: Medium speed + 2: Fast speed + 3: High speed + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [0, 1, 2, 3] + + required: + - pinmux + +required: + - compatible + - '#address-cells' + - '#size-cells' + - ranges + - pins-are-numbered + +examples: + - | + #include + //Example 1 + pinctrl@40020000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stm32f429-pinctrl"; + ranges = <0 0x40020000 0x3000>; + pins-are-numbered; + + gpioa: gpio@0 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x400>; + resets = <&reset_ahb1 0>; + st,bank-name = "GPIOA"; + }; + }; + + //Example 2 (using gpio-ranges) + pinctrl@50020000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stm32f429-pinctrl"; + ranges = <0 0x50020000 0x3000>; + pins-are-numbered; + + gpiob: gpio@1000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x1000 0x400>; + resets = <&reset_ahb1 0>; + st,bank-name = "GPIOB"; + gpio-ranges = <&pinctrl 0 0 16>; + }; + + gpioc: gpio@2000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x2000 0x400>; + resets = <&reset_ahb1 0>; + st,bank-name = "GPIOC"; + ngpios = <5>; + gpio-ranges = <&pinctrl 0 16 3>, + <&pinctrl 14 30 2>; + }; + }; + + //Example 3 pin groups + pinctrl@60020000 { + usart1_pins_a: usart1-0 { + pins1 { + pinmux = ; + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = ; + bias-disable; + }; + }; + }; + + usart1 { + pinctrl-0 = <&usart1_pins_a>; + pinctrl-names = "default"; + }; + +... -- cgit v1.2.3 From 1254db248fce4e2cf05a01c1c8df3b79745424c0 Mon Sep 17 00:00:00 2001 From: Jerome Brunet Date: Thu, 16 May 2019 17:13:38 +0200 Subject: dt-bindings: pinctrl: meson: add output support in pinconf add support for the pinconf DT property output-enable, output-disable, output-low and output-high in the meson pinctrl driver. Signed-off-by: Jerome Brunet Signed-off-by: Linus Walleij --- Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt | 12 +++++++++--- 1 file changed, 9 insertions(+), 3 deletions(-) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index a7618605bf1e..10dc4f7176ca 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -47,9 +47,15 @@ Required properties for pinmux nodes are: Required properties for configuration nodes: - pins: a list of pin names -Configuration nodes support the generic properties "bias-disable", -"bias-pull-up" and "bias-pull-down", described in file -pinctrl-bindings.txt +Configuration nodes support the following generic properties, as +described in file pinctrl-bindings.txt: + - "bias-disable" + - "bias-pull-up" + - "bias-pull-down" + - "output-enable" + - "output-disable" + - "output-low" + - "output-high" Optional properties : - drive-strength-microamp: Drive strength for the specified pins in uA. -- cgit v1.2.3 From 13531e5d359e30d9e3d1cabd246a24cf6fdf084a Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Mon, 20 May 2019 14:00:57 +0530 Subject: dt-bindings: pinctrl: Modify pinctrl memory map Earlier, the PWM registers were included as part of the pinctrl memory map, but this turned to be useless as the muxing is being handled by the SoC pin controller itself. So, lets modify the pinctrl memory map to reflect the same. Fixes: 07b734fbdea2 ("dt-bindings: pinctrl: Add BM1880 pinctrl binding") Signed-off-by: Manivannan Sadhasivam Signed-off-by: Linus Walleij --- Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt index ed34bb1ee81c..cc9a89aa4170 100644 --- a/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt @@ -85,9 +85,9 @@ Required Properties: spi0 Example: - pinctrl: pinctrl@50 { + pinctrl: pinctrl@400 { compatible = "bitmain,bm1880-pinctrl"; - reg = <0x50 0x4B0>; + reg = <0x400 0x120>; pinctrl_uart0_default: uart0-default { pinmux { -- cgit v1.2.3 From 752a74038dbd999c108f1c7474908f7501e246bb Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Mon, 20 May 2019 14:01:00 +0530 Subject: dt-bindings: pinctrl: Document pinconf bindings for BM1880 SoC Document pinconf bindings for Bitmain BM1880 SoC. Signed-off-by: Manivannan Sadhasivam Signed-off-by: Linus Walleij --- .../bindings/pinctrl/bitmain,bm1880-pinctrl.txt | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt index cc9a89aa4170..4eb089bcb5f3 100644 --- a/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt @@ -14,7 +14,8 @@ phrase "pin configuration node". The pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration for BM1880 SoC -includes only pinmux as there is no pinconf support available in SoC. +includes pinmux and various pin configuration parameters, such as pull-up, +slew rate etc... Each configuration node can consist of multiple nodes describing the pinmux options. The name of each subnode is not important; all subnodes should be @@ -84,6 +85,22 @@ Required Properties: gpio66, gpio67, eth1, i2s0, i2s0_mclkin, i2s1, i2s1_mclkin, spi0 +Optional Properties: + +- bias-disable: No arguments. Disable pin bias. +- bias-pull-down: No arguments. The specified pins should be configured as + pull down. +- bias-pull-up: No arguments. The specified pins should be configured as + pull up. +- input-schmitt-enable: No arguments: Enable schmitt trigger for the specified + pins +- input-schmitt-disable: No arguments: Disable schmitt trigger for the specified + pins +- slew-rate: Integer. Sets slew rate for the specified pins. + Valid values are: + <0> - Slow + <1> - Fast + Example: pinctrl: pinctrl@400 { compatible = "bitmain,bm1880-pinctrl"; -- cgit v1.2.3 From e618795367df99c463f5e4e0ddee9612fcce6b06 Mon Sep 17 00:00:00 2001 From: Colin Ian King Date: Sat, 25 May 2019 21:42:28 +0100 Subject: dt-bindings: pinctrl: fix spelling mistakes in pinctl documentation The spelling of configured is incorrect in the documentation. Fix it. Signed-off-by: Colin Ian King Reviewed-by: Bjorn Andersson Signed-off-by: Linus Walleij --- Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt | 6 +++--- Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt | 6 +++--- Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt | 6 +++--- Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt | 6 +++--- Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt | 6 +++--- Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt | 6 +++--- Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.txt | 6 +++--- Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt | 6 +++--- Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt | 6 +++--- Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt | 6 +++--- Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt | 6 +++--- 11 files changed, 33 insertions(+), 33 deletions(-) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt index 68e93d5b7ede..c9782397ff14 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt @@ -122,17 +122,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt index 6dd72f8599e9..7b151894f5a0 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt @@ -118,17 +118,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt index 86ecdcfc4fb8..d46973968873 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.txt @@ -97,17 +97,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt index 195a7a0ef0cc..3354a63296d9 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt @@ -130,17 +130,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt index 5034eb6653c7..a7dd213c77c6 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt @@ -124,17 +124,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt index f15443f6e78e..da52df6273bc 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.txt @@ -128,17 +128,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.txt index fa97f609fe45..a56cb882830c 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.txt @@ -149,17 +149,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt index e70c79bbbc5b..00174f08ba1d 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt @@ -135,17 +135,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt index 2b8f77762edc..a50e74684195 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt @@ -150,17 +150,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt index 769ca83bb40d..be034d329e10 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt @@ -142,17 +142,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt index 665aadb5ea28..321bdb9be0d2 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt @@ -118,17 +118,17 @@ to specify in a pin configuration subnode: - bias-disable: Usage: optional Value type: - Definition: The specified pins should be configued as no pull. + Definition: The specified pins should be configured as no pull. - bias-pull-down: Usage: optional Value type: - Definition: The specified pins should be configued as pull down. + Definition: The specified pins should be configured as pull down. - bias-pull-up: Usage: optional Value type: - Definition: The specified pins should be configued as pull up. + Definition: The specified pins should be configured as pull up. - output-high: Usage: optional -- cgit v1.2.3 From 2585a584f8444e10a5a9e234c0c38b81dfe4370a Mon Sep 17 00:00:00 2001 From: Krishna Yarlagadda Date: Thu, 16 May 2019 17:23:11 +0530 Subject: pinctrl: Add Tegra194 pinctrl DT bindings Add binding doc for Tegra 194 pinctrl driver. Signed-off-by: Krishna Yarlagadda Tested-by: Vidya Sagar Reviewed-by: Rob Herring Signed-off-by: Linus Walleij --- .../bindings/pinctrl/nvidia,tegra194-pinmux.txt | 107 +++++++++++++++++++++ 1 file changed, 107 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/nvidia,tegra194-pinmux.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra194-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra194-pinmux.txt new file mode 100644 index 000000000000..8763f448c376 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra194-pinmux.txt @@ -0,0 +1,107 @@ +NVIDIA Tegra194 pinmux controller + +Required properties: +- compatible: "nvidia,tegra194-pinmux" +- reg: Should contain a list of base address and size pairs for: + - first entry: The APB_MISC_GP_*_PADCTRL registers (pad control) + - second entry: The PINMUX_AUX_* registers (pinmux) + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Tegra's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, tristate, drive strength, etc. + +See the TRM to determine which properties and values apply to each pin/group. +Macro values for property values are defined in +include/dt-binding/pinctrl/pinctrl-tegra.h. + +Required subnode-properties: +- nvidia,pins : An array of strings. Each string contains the name of a pin or + group. Valid values for these names are listed below. + +Optional subnode-properties: +- nvidia,function: A string containing the name of the function to mux to the + pin or group. +- nvidia,pull: Integer, representing the pull-down/up to apply to the pin. + 0: none, 1: down, 2: up. +- nvidia,tristate: Integer. + 0: drive, 1: tristate. +- nvidia,enable-input: Integer. Enable the pin's input path. + enable :TEGRA_PIN_ENABLE and + disable or output only: TEGRA_PIN_DISABLE. +- nvidia,open-drain: Integer. + enable: TEGRA_PIN_ENABLE. + disable: TEGRA_PIN_DISABLE. +- nvidia,lock: Integer. Lock the pin configuration against further changes + until reset. + enable: TEGRA_PIN_ENABLE. + disable: TEGRA_PIN_DISABLE. +- nvidia,io-hv: Integer. Select high-voltage receivers. + normal: TEGRA_PIN_DISABLE + high: TEGRA_PIN_ENABLE +- nvidia,schmitt: Integer. Enables Schmitt Trigger on the input. + normal: TEGRA_PIN_DISABLE + high: TEGRA_PIN_ENABLE +- nvidia,drive-type: Integer. Valid range 0...3. +- nvidia,pull-down-strength: Integer. Controls drive strength. 0 is weakest. + The range of valid values depends on the pingroup. See "CAL_DRVDN" in the + Tegra TRM. +- nvidia,pull-up-strength: Integer. Controls drive strength. 0 is weakest. + The range of valid values depends on the pingroup. See "CAL_DRVUP" in the + Tegra TRM. + +Valid values for pin and group names (nvidia,pin) are: + + These correspond to Tegra PADCTL_* (pinmux) registers. + + Mux groups: + + These correspond to Tegra PADCTL_* (pinmux) registers. Any property + that exists in those registers may be set for the following pin names. + + pex_l5_clkreq_n_pgg0, pex_l5_rst_n_pgg1 + + Drive groups: + + These registers controls a single pin for which a mux group exists. + See the list above for the pin name to use when configuring the pinmux. + + pex_l5_clkreq_n_pgg0, pex_l5_rst_n_pgg1 + +Valid values for nvidia,functions are: + + pe5 + +Power Domain: + pex_l5_clkreq_n_pgg0 and pex_l5_rst_n_pgg1 are part of PCIE C5 power + partition. Client devices must enable this partition before accessing + these pins here. + + +Example: + + tegra_pinctrl: pinmux: pinmux@2430000 { + compatible = "nvidia,tegra194-pinmux"; + reg = <0x2430000 0x17000 + 0xc300000 0x4000>; + + pinctrl-names = "pex_rst"; + pinctrl-0 = <&pex_rst_c5_out_state>; + + pex_rst_c5_out_state: pex_rst_c5_out { + pex_rst { + nvidia,pins = "pex_l5_rst_n_pgg1"; + nvidia,schmitt = ; + nvidia,lpdr = ; + nvidia,enable-input = ; + nvidia,io-high-voltage = ; + nvidia,tristate = ; + nvidia,pull = ; + }; + }; + }; -- cgit v1.2.3 From 3a11cf2217520e3c827a24c6d5f648fa45845787 Mon Sep 17 00:00:00 2001 From: Anson Huang Date: Thu, 30 May 2019 11:13:57 +0800 Subject: dt-bindings: imx: Correct pinfunc head file path for i.MX8MM The i.MX8MM pinfunc head file is located in DT folder, correct it. Signed-off-by: Anson Huang Signed-off-by: Linus Walleij --- Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt index 524a16fca666..e4e01c05cf83 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt @@ -12,7 +12,7 @@ Required properties in sub-nodes: - fsl,pins: each entry consists of 6 integers and represents the mux and config setting for one pin. The first 5 integers are specified using a PIN_FUNC_ID macro, which can be found in - . The last integer CONFIG is + . The last integer CONFIG is the pad setting value like pull-up on this pin. Please refer to i.MX8M Mini Reference Manual for detailed CONFIG settings. -- cgit v1.2.3 From 7ea6a2edbfd0a98f729f6f4705535bc53ec1a89f Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Mon, 3 Jun 2019 13:04:20 +0530 Subject: dt-bindings: pinctrl: Document drive strength settings for BM1880 SoC Document drive strength settings for Bitmain BM1880 SoC. Signed-off-by: Manivannan Sadhasivam Signed-off-by: Linus Walleij --- .../devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt | 11 +++++++++++ 1 file changed, 11 insertions(+) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt index 4eb089bcb5f3..4980776122cc 100644 --- a/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/bitmain,bm1880-pinctrl.txt @@ -100,6 +100,17 @@ Optional Properties: Valid values are: <0> - Slow <1> - Fast +- drive-strength: Integer. Selects the drive strength for the specified + pins in mA. + Valid values are: + <4> + <8> + <12> + <16> + <20> + <24> + <28> + <32> Example: pinctrl: pinctrl@400 { -- cgit v1.2.3 From 53a5372ce326116f3e3d3f1d701113b2542509f4 Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Tue, 4 Jun 2019 00:19:59 -0700 Subject: pinctrl: qcom: sdm845: Expose ufs_reset as gpio The ufs_reset pin is expected to be wired to the reset pin of the primary UFS memory but is pretty much just a general purpose output pinr Reorder the pins and expose it as gpio 150, so that the UFS driver can toggle it. Signed-off-by: Bjorn Andersson Signed-off-by: Linus Walleij --- .../devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt | 2 +- drivers/pinctrl/qcom/pinctrl-sdm845.c | 12 ++++++------ 2 files changed, 7 insertions(+), 7 deletions(-) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt index 321bdb9be0d2..7462e3743c68 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt @@ -79,7 +79,7 @@ to specify in a pin configuration subnode: gpio0-gpio149 Supports mux, bias and drive-strength - sdc2_clk, sdc2_cmd, sdc2_data + sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset Supports bias and drive-strength - function: diff --git a/drivers/pinctrl/qcom/pinctrl-sdm845.c b/drivers/pinctrl/qcom/pinctrl-sdm845.c index c97f20fca5fd..e4e5acade086 100644 --- a/drivers/pinctrl/qcom/pinctrl-sdm845.c +++ b/drivers/pinctrl/qcom/pinctrl-sdm845.c @@ -420,10 +420,10 @@ DECLARE_MSM_GPIO_PINS(147); DECLARE_MSM_GPIO_PINS(148); DECLARE_MSM_GPIO_PINS(149); -static const unsigned int sdc2_clk_pins[] = { 150 }; -static const unsigned int sdc2_cmd_pins[] = { 151 }; -static const unsigned int sdc2_data_pins[] = { 152 }; -static const unsigned int ufs_reset_pins[] = { 153 }; +static const unsigned int ufs_reset_pins[] = { 150 }; +static const unsigned int sdc2_clk_pins[] = { 151 }; +static const unsigned int sdc2_cmd_pins[] = { 152 }; +static const unsigned int sdc2_data_pins[] = { 153 }; enum sdm845_functions { msm_mux_gpio, @@ -1271,10 +1271,10 @@ static const struct msm_pingroup sdm845_groups[] = { PINGROUP(147, NORTH, _, _, _, _, _, _, _, _, _, _), PINGROUP(148, NORTH, _, _, _, _, _, _, _, _, _, _), PINGROUP(149, NORTH, _, _, _, _, _, _, _, _, _, _), + UFS_RESET(ufs_reset, 0x99f000), SDC_QDSD_PINGROUP(sdc2_clk, 0x99a000, 14, 6), SDC_QDSD_PINGROUP(sdc2_cmd, 0x99a000, 11, 3), SDC_QDSD_PINGROUP(sdc2_data, 0x99a000, 9, 0), - UFS_RESET(ufs_reset, 0x99f000), }; static const struct msm_pinctrl_soc_data sdm845_pinctrl = { @@ -1284,7 +1284,7 @@ static const struct msm_pinctrl_soc_data sdm845_pinctrl = { .nfunctions = ARRAY_SIZE(sdm845_functions), .groups = sdm845_groups, .ngroups = ARRAY_SIZE(sdm845_groups), - .ngpios = 150, + .ngpios = 151, }; static int sdm845_pinctrl_probe(struct platform_device *pdev) -- cgit v1.2.3 From 76c4c597b2ef59900933fca8893428f0555afaab Mon Sep 17 00:00:00 2001 From: Hongwei Zhang Date: Tue, 4 Jun 2019 17:53:32 -0400 Subject: pinctrl: aspeed: Add SGPM pinmux Add SGPM pinmux to ast2500-pinctrl function and group, to prepare for supporting SGPIO in AST2500 SoC. Signed-off-by: Hongwei Zhang Reviewed-by: Andrew Jeffery Signed-off-by: Linus Walleij --- Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt | 2 +- drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c | 4 ++++ 2 files changed, 5 insertions(+), 1 deletion(-) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt index 3b7266c7c438..8f1c5c4d62f9 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt @@ -84,7 +84,7 @@ NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 NDTR1 NDTR2 NDTR3 NDTR4 NRI1 NRI2 NRI3 NRI4 NRTS1 NRTS2 NRTS3 NRTS4 OSCCLK PEWAKE PNOR PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 RXD1 RXD2 RXD3 RXD4 SALT1 SALT10 SALT11 SALT12 SALT13 SALT14 SALT2 SALT3 SALT4 SALT5 SALT6 SALT7 SALT8 SALT9 -SCL1 SCL2 SD1 SD2 SDA1 SDA2 SGPS1 SGPS2 SIOONCTRL SIOPBI SIOPBO SIOPWREQ +SCL1 SCL2 SD1 SD2 SDA1 SDA2 SGPM SGPS1 SGPS2 SIOONCTRL SIOPBI SIOPBO SIOPWREQ SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1CS1 SPI1DEBUG SPI1PASSTHRU SPI2CK SPI2CS0 SPI2CS1 SPI2MISO SPI2MOSI TIMER3 TIMER4 TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 TXD3 TXD4 UART6 USB11BHID USB2AD USB2AH USB2BD USB2BH USBCKI VGABIOSROM VGAHS diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c b/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c index 187abd7693cf..0c89647f166f 100644 --- a/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c +++ b/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c @@ -577,6 +577,8 @@ SS_PIN_DECL(N3, GPIOJ2, SGPMO); SIG_EXPR_LIST_DECL_SINGLE(SGPMI, SGPM, SIG_DESC_SET(SCU84, 11)); SS_PIN_DECL(N4, GPIOJ3, SGPMI); +FUNC_GROUP_DECL(SGPM, R2, L2, N3, N4); + #define N5 76 SIG_EXPR_LIST_DECL_SINGLE(VGAHS, VGAHS, SIG_DESC_SET(SCU84, 12)); SIG_EXPR_LIST_DECL_SINGLE(DASHN5, DASHN5, SIG_DESC_SET(SCU94, 8)); @@ -2127,6 +2129,7 @@ static const struct aspeed_pin_group aspeed_g5_groups[] = { ASPEED_PINCTRL_GROUP(SD2), ASPEED_PINCTRL_GROUP(SDA1), ASPEED_PINCTRL_GROUP(SDA2), + ASPEED_PINCTRL_GROUP(SGPM), ASPEED_PINCTRL_GROUP(SGPS1), ASPEED_PINCTRL_GROUP(SGPS2), ASPEED_PINCTRL_GROUP(SIOONCTRL), @@ -2296,6 +2299,7 @@ static const struct aspeed_pin_function aspeed_g5_functions[] = { ASPEED_PINCTRL_FUNC(SD2), ASPEED_PINCTRL_FUNC(SDA1), ASPEED_PINCTRL_FUNC(SDA2), + ASPEED_PINCTRL_FUNC(SGPM), ASPEED_PINCTRL_FUNC(SGPS1), ASPEED_PINCTRL_FUNC(SGPS2), ASPEED_PINCTRL_FUNC(SIOONCTRL), -- cgit v1.2.3 From d6e561df50b5a7e33273f66f97bf2b4ff25f13b4 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Fri, 7 Jun 2019 13:06:12 +0200 Subject: dt-bindings: pinctrl: pic32: Spelling s/configuraion/configuration/ Signed-off-by: Geert Uytterhoeven Signed-off-by: Linus Walleij --- Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt index 29b72e303ebf..51efd2085113 100644 --- a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt @@ -5,7 +5,7 @@ Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and pin controller, GPIO, and interrupt bindings. PIC32 'pin configuration node' is a node of a group of pins which can be -used for a specific device or function. This node represents configuraions of +used for a specific device or function. This node represents configurations of pins, optional function, and optional mux related configuration. Required properties for pin controller node: -- cgit v1.2.3 From 1d90dff62e16fee5bdc761c3230cc8a4c79814fc Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Tue, 11 Jun 2019 22:09:30 +0800 Subject: dt-bindings: pinctrl: add missing compatible string for V3s The pinctrl driver of V3s is already available and used in the kernel, but the compatible string of it is forgotten to be added. Add the missing compatible string. Signed-off-by: Icenowy Zheng Acked-by: Maxime Ripard Reviewed-by: Rob Herring Signed-off-by: Linus Walleij --- Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 + 1 file changed, 1 insertion(+) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index cf96b7c20e4d..baba55db864c 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -24,6 +24,7 @@ Required properties: "allwinner,sun8i-h3-pinctrl" "allwinner,sun8i-h3-r-pinctrl" "allwinner,sun8i-r40-pinctrl" + "allwinner,sun8i-v3s-pinctrl" "allwinner,sun50i-a64-pinctrl" "allwinner,sun50i-a64-r-pinctrl" "allwinner,sun50i-h5-pinctrl" -- cgit v1.2.3 From 2e80e10f2d71f42c6c8f82fc173b21be856acc0f Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Tue, 11 Jun 2019 22:09:31 +0800 Subject: dt-bindings: pinctrl: add compatible string for Allwinner V3 pinctrl The Allwinner V3 SoC, despite come with the same die with V3s, has more GPIO pins than V3s, and a different compatible string for pinctrl is needed. Add the compatible string for V3 pinctrl. Signed-off-by: Icenowy Zheng Reviewed-by: Rob Herring Signed-off-by: Linus Walleij --- Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 + 1 file changed, 1 insertion(+) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index baba55db864c..328585c6da58 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -24,6 +24,7 @@ Required properties: "allwinner,sun8i-h3-pinctrl" "allwinner,sun8i-h3-r-pinctrl" "allwinner,sun8i-r40-pinctrl" + "allwinner,sun8i-v3-pinctrl" "allwinner,sun8i-v3s-pinctrl" "allwinner,sun50i-a64-pinctrl" "allwinner,sun50i-a64-r-pinctrl" -- cgit v1.2.3 From 124ecd6658e7ec2f1f14cfa36be76ac0f88cc33e Mon Sep 17 00:00:00 2001 From: Anson Huang Date: Tue, 11 Jun 2019 20:25:33 +0800 Subject: dt-bindings: imx: Add pinctrl binding doc for i.MX8MN Add binding doc for i.MX8MN pinctrl driver. Signed-off-by: Anson Huang Acked-by: Dong Aisheng Signed-off-by: Linus Walleij --- .../bindings/pinctrl/fsl,imx8mn-pinctrl.txt | 39 ++ arch/arm64/boot/dts/freescale/imx8mn-pinfunc.h | 646 +++++++++++++++++++++ 2 files changed, 685 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx8mn-pinctrl.txt create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-pinfunc.h (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mn-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mn-pinctrl.txt new file mode 100644 index 000000000000..330716c971b9 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mn-pinctrl.txt @@ -0,0 +1,39 @@ +* Freescale IMX8MN IOMUX Controller + +Please refer to fsl,imx-pinctrl.txt and pinctrl-bindings.txt in this directory +for common binding part and usage. + +Required properties: +- compatible: "fsl,imx8mn-iomuxc" +- reg: should contain the base physical address and size of the iomuxc + registers. + +Required properties in sub-nodes: +- fsl,pins: each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers are specified using a PIN_FUNC_ID macro, which can be found in + . The last integer CONFIG is + the pad setting value like pull-up on this pin. Please refer to i.MX8M Nano + Reference Manual for detailed CONFIG settings. + +Examples: + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; +}; + +iomuxc: pinctrl@30330000 { + compatible = "fsl,imx8mn-iomuxc"; + reg = <0x0 0x30330000 0x0 0x10000>; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + MX8MN_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140 + MX8MN_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140 + MX8MN_IOMUXC_SD1_DATA4_GPIO2_IO6 0x19 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mn-pinfunc.h b/arch/arm64/boot/dts/freescale/imx8mn-pinfunc.h new file mode 100644 index 000000000000..faf1e69e742b --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mn-pinfunc.h @@ -0,0 +1,646 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2018-2019 NXP + */ + +#ifndef __DTS_IMX8MN_PINFUNC_H +#define __DTS_IMX8MN_PINFUNC_H + +/* + * The pin function ID is a tuple of + * + */ + +#define MX8MN_IOMUXC_BOOT_MODE2_CCMSRCGPCMIX_BOOT_MODE2 0x020 0x25C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_BOOT_MODE2_I2C1_SCL 0x020 0x25C 0x55C 0x1 0x3 +#define MX8MN_IOMUXC_BOOT_MODE3_CCMSRCGPCMIX_BOOT_MODE3 0x024 0x260 0x000 0x0 0x0 +#define MX8MN_IOMUXC_BOOT_MODE3_I2C1_SDA 0x024 0x260 0x56C 0x1 0x3 +#define MX8MN_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x028 0x290 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO00_CCMSRCGPCMIX_ENET_PHY_REF_CLK_ROOT 0x028 0x290 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x028 0x290 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO00_CCMSRCGPCMIX_EXT_CLK1 0x028 0x290 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x02C 0x294 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO01_PWM1_OUT 0x02C 0x294 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO01_ANAMIX_REF_CLK_24M 0x02C 0x294 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO01_CCMSRCGPCMIX_EXT_CLK2 0x02C 0x294 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO02_GPIO1_IO2 0x030 0x298 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x030 0x298 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_ANY 0x030 0x298 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x034 0x29C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO03_USDHC1_VSELECT 0x034 0x29C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO03_SDMA1_EXT_EVENT0 0x034 0x29C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO03_ANAMIX_XTAL_OK 0x034 0x29C 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x038 0x2A0 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x038 0x2A0 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO04_SDMA1_EXT_EVENT1 0x038 0x2A0 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO04_ANAMIX_XTAL_OK_LV 0x038 0x2A0 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x03C 0x2A4 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO05_M4_NMI 0x03C 0x2A4 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO05_CCMSRCGPCMIX_PMIC_READY 0x03C 0x2A4 0x4BC 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO05_CCMSRCGPCMIX_INT_BOOT 0x03C 0x2A4 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x040 0x2A8 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO06_ENET1_MDC 0x040 0x2A8 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO06_USDHC1_CD_B 0x040 0x2A8 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO06_CCMSRCGPCMIX_EXT_CLK3 0x040 0x2A8 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x044 0x2AC 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO07_ENET1_MDIO 0x044 0x2AC 0x4C0 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO07_USDHC1_WP 0x044 0x2AC 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO07_CCMSRCGPCMIX_EXT_CLK4 0x044 0x2AC 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x048 0x2B0 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO08_ENET1_1588_EVENT0_IN 0x048 0x2B0 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO08_PWM1_OUT 0x048 0x2B0 0x000 0x2 0x0 +#define MX8MN_IOMUXC_GPIO1_IO08_USDHC2_RESET_B 0x048 0x2B0 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO08_CCMSRCGPCMIX_WAIT 0x048 0x2B0 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x04C 0x2B4 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO09_ENET1_1588_EVENT0_OUT 0x04C 0x2B4 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO09_PWM2_OUT 0x04C 0x2B4 0x000 0x2 0x0 +#define MX8MN_IOMUXC_GPIO1_IO09_USDHC3_RESET_B 0x04C 0x2B4 0x000 0x4 0x0 +#define MX8MN_IOMUXC_GPIO1_IO09_SDMA2_EXT_EVENT0 0x04C 0x2B4 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO09_CCMSRCGPCMIX_STOP 0x04C 0x2B4 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x050 0x2B8 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO10_USB1_OTG_ID 0x050 0x2B8 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO10_PWM3_OUT 0x050 0x2B8 0x000 0x2 0x0 +#define MX8MN_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x054 0x2BC 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO11_PWM2_OUT 0x054 0x2BC 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO11_USDHC3_VSELECT 0x054 0x2BC 0x000 0x4 0x0 +#define MX8MN_IOMUXC_GPIO1_IO11_CCMSRCGPCMIX_PMIC_READY 0x054 0x2BC 0x4BC 0x5 0x1 +#define MX8MN_IOMUXC_GPIO1_IO11_CCMSRCGPCMIX_OUT0 0x054 0x2BC 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x058 0x2C0 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO12_USB1_OTG_PWR 0x058 0x2C0 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO12_SDMA2_EXT_EVENT1 0x058 0x2C0 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO12_CCMSRCGPCMIX_OUT1 0x058 0x2C0 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x05C 0x2C4 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x05C 0x2C4 0x000 0x1 0x0 +#define MX8MN_IOMUXC_GPIO1_IO13_PWM2_OUT 0x05C 0x2C4 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO13_CCMSRCGPCMIX_OUT2 0x05C 0x2C4 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x060 0x2C8 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO14_USDHC3_CD_B 0x060 0x2C8 0x598 0x4 0x2 +#define MX8MN_IOMUXC_GPIO1_IO14_PWM3_OUT 0x060 0x2C8 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1 0x060 0x2C8 0x000 0x6 0x0 +#define MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x064 0x2CC 0x000 0x0 0x0 +#define MX8MN_IOMUXC_GPIO1_IO15_USDHC3_WP 0x064 0x2CC 0x5B8 0x4 0x2 +#define MX8MN_IOMUXC_GPIO1_IO15_PWM4_OUT 0x064 0x2CC 0x000 0x5 0x0 +#define MX8MN_IOMUXC_GPIO1_IO15_CCMSRCGPCMIX_CLKO2 0x064 0x2CC 0x000 0x6 0x0 +#define MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x068 0x2D0 0x000 0x0 0x0 +#define MX8MN_IOMUXC_ENET_MDC_SAI6_TX_DATA0 0x068 0x2D0 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_MDC_PDM_BIT_STREAM3 0x068 0x2D0 0x540 0x3 0x1 +#define MX8MN_IOMUXC_ENET_MDC_SPDIF1_OUT 0x068 0x2D0 0x000 0x4 0x0 +#define MX8MN_IOMUXC_ENET_MDC_GPIO1_IO16 0x068 0x2D0 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_MDC_USDHC3_STROBE 0x068 0x2D0 0x59C 0x6 0x1 +#define MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x06C 0x2D4 0x4C0 0x0 0x1 +#define MX8MN_IOMUXC_ENET_MDIO_SAI6_TX_SYNC 0x06C 0x2D4 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_MDIO_PDM_BIT_STREAM2 0x06C 0x2D4 0x53C 0x3 0x1 +#define MX8MN_IOMUXC_ENET_MDIO_SPDIF1_IN 0x06C 0x2D4 0x5CC 0x4 0x1 +#define MX8MN_IOMUXC_ENET_MDIO_GPIO1_IO17 0x06C 0x2D4 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_MDIO_USDHC3_DATA5 0x06C 0x2D4 0x550 0x6 0x1 +#define MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x070 0x2D8 0x000 0x0 0x0 +#define MX8MN_IOMUXC_ENET_TD3_SAI6_TX_BCLK 0x070 0x2D8 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_TD3_PDM_BIT_STREAM1 0x070 0x2D8 0x538 0x3 0x1 +#define MX8MN_IOMUXC_ENET_TD3_SPDIF1_EXT_CLK 0x070 0x2D8 0x568 0x4 0x1 +#define MX8MN_IOMUXC_ENET_TD3_GPIO1_IO18 0x070 0x2D8 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_TD3_USDHC3_DATA6 0x070 0x2D8 0x584 0x6 0x1 +#define MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x074 0x2DC 0x000 0x0 0x0 +#define MX8MN_IOMUXC_ENET_TD2_ENET1_TX_CLK 0x074 0x2DC 0x5A4 0x1 0x0 +#define MX8MN_IOMUXC_ENET_TD2_CCMSRCGPCMIX_ENET_REF_CLK_ROOT 0x074 0x2DC 0x5A4 0x1 0x0 +#define MX8MN_IOMUXC_ENET_TD2_SAI6_RX_DATA0 0x074 0x2DC 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_TD2_PDM_BIT_STREAM3 0x074 0x2DC 0x540 0x3 0x2 +#define MX8MN_IOMUXC_ENET_TD2_GPIO1_IO19 0x074 0x2DC 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_TD2_USDHC3_DATA7 0x074 0x2DC 0x54C 0x6 0x1 +#define MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x078 0x2E0 0x000 0x0 0x0 +#define MX8MN_IOMUXC_ENET_TD1_SAI6_RX_SYNC 0x078 0x2E0 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_TD1_PDM_BIT_STREAM2 0x078 0x2E0 0x53C 0x3 0x2 +#define MX8MN_IOMUXC_ENET_TD1_GPIO1_IO20 0x078 0x2E0 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_TD1_USDHC3_CD_B 0x078 0x2E0 0x598 0x6 0x3 +#define MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x07C 0x2E4 0x000 0x0 0x0 +#define MX8MN_IOMUXC_ENET_TD0_SAI6_RX_BCLK 0x07C 0x2E4 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_TD0_PDM_BIT_STREAM1 0x07C 0x2E4 0x538 0x3 0x2 +#define MX8MN_IOMUXC_ENET_TD0_GPIO1_IO21 0x07C 0x2E4 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_TD0_USDHC3_WP 0x07C 0x2E4 0x5B8 0x6 0x3 +#define MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x080 0x2E8 0x000 0x0 0x0 +#define MX8MN_IOMUXC_ENET_TX_CTL_SAI6_MCLK 0x080 0x2E8 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_TX_CTL_GPIO1_IO22 0x080 0x2E8 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_TX_CTL_USDHC3_DATA0 0x080 0x2E8 0x5B4 0x6 0x1 +#define MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x084 0x2EC 0x000 0x0 0x0 +#define MX8MN_IOMUXC_ENET_TXC_ENET1_TX_ER 0x084 0x2EC 0x000 0x1 0x0 +#define MX8MN_IOMUXC_ENET_TXC_SAI7_TX_DATA0 0x084 0x2EC 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_TXC_GPIO1_IO23 0x084 0x2EC 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_TXC_USDHC3_DATA1 0x084 0x2EC 0x5B0 0x6 0x1 +#define MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x088 0x2F0 0x574 0x0 0x0 +#define MX8MN_IOMUXC_ENET_RX_CTL_SAI7_TX_SYNC 0x088 0x2F0 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_RX_CTL_PDM_BIT_STREAM3 0x088 0x2F0 0x540 0x3 0x3 +#define MX8MN_IOMUXC_ENET_RX_CTL_GPIO1_IO24 0x088 0x2F0 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_RX_CTL_USDHC3_DATA2 0x088 0x2F0 0x5E4 0x6 0x1 +#define MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x08C 0x2F4 0x000 0x0 0x0 +#define MX8MN_IOMUXC_ENET_RXC_ENET1_RX_ER 0x08C 0x2F4 0x5C8 0x1 0x0 +#define MX8MN_IOMUXC_ENET_RXC_SAI7_TX_BCLK 0x08C 0x2F4 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_RXC_PDM_BIT_STREAM2 0x08C 0x2F4 0x53C 0x3 0x3 +#define MX8MN_IOMUXC_ENET_RXC_GPIO1_IO25 0x08C 0x2F4 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_RXC_USDHC3_DATA3 0x08C 0x2F4 0x5E0 0x6 0x1 +#define MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x090 0x2F8 0x57C 0x0 0x0 +#define MX8MN_IOMUXC_ENET_RD0_SAI7_RX_DATA0 0x090 0x2F8 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_RD0_PDM_BIT_STREAM1 0x090 0x2F8 0x538 0x3 0x3 +#define MX8MN_IOMUXC_ENET_RD0_GPIO1_IO26 0x090 0x2F8 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_RD0_USDHC3_DATA4 0x090 0x2F8 0x558 0x6 0x1 +#define MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x094 0x2FC 0x554 0x0 0x0 +#define MX8MN_IOMUXC_ENET_RD1_SAI7_RX_SYNC 0x094 0x2FC 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_RD1_PDM_BIT_STREAM0 0x094 0x2FC 0x534 0x3 0x1 +#define MX8MN_IOMUXC_ENET_RD1_GPIO1_IO27 0x094 0x2FC 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_RD1_USDHC3_RESET_B 0x094 0x2FC 0x000 0x6 0x0 +#define MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x098 0x300 0x000 0x0 0x0 +#define MX8MN_IOMUXC_ENET_RD2_SAI7_RX_BCLK 0x098 0x300 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_RD2_PDM_CLK 0x098 0x300 0x000 0x3 0x0 +#define MX8MN_IOMUXC_ENET_RD2_GPIO1_IO28 0x098 0x300 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_RD2_USDHC3_CLK 0x098 0x300 0x5A0 0x6 0x1 +#define MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x09C 0x304 0x000 0x0 0x0 +#define MX8MN_IOMUXC_ENET_RD3_SAI7_MCLK 0x09C 0x304 0x000 0x2 0x0 +#define MX8MN_IOMUXC_ENET_RD3_SPDIF1_IN 0x09C 0x304 0x5CC 0x3 0x5 +#define MX8MN_IOMUXC_ENET_RD3_GPIO1_IO29 0x09C 0x304 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ENET_RD3_USDHC3_CMD 0x09C 0x304 0x5DC 0x6 0x1 +#define MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK 0x0A0 0x308 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD1_CLK_ENET1_MDC 0x0A0 0x308 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SD1_CLK_UART1_DCE_TX 0x0A0 0x308 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD1_CLK_UART1_DTE_RX 0x0A0 0x308 0x4F4 0x4 0x4 +#define MX8MN_IOMUXC_SD1_CLK_GPIO2_IO0 0x0A0 0x308 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD 0x0A4 0x30C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD1_CMD_ENET1_MDIO 0x0A4 0x30C 0x4C0 0x1 0x3 +#define MX8MN_IOMUXC_SD1_CMD_UART1_DCE_RX 0x0A4 0x30C 0x4F4 0x4 0x5 +#define MX8MN_IOMUXC_SD1_CMD_UART1_DTE_TX 0x0A4 0x30C 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD1_CMD_GPIO2_IO1 0x0A4 0x30C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x0A8 0x310 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD1_DATA0_ENET1_RGMII_TD1 0x0A8 0x310 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SD1_DATA0_UART1_DCE_RTS_B 0x0A8 0x310 0x4F0 0x4 0x4 +#define MX8MN_IOMUXC_SD1_DATA0_UART1_DTE_CTS_B 0x0A8 0x310 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD1_DATA0_GPIO2_IO2 0x0A8 0x310 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x0AC 0x314 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD1_DATA1_ENET1_RGMII_TD0 0x0AC 0x314 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SD1_DATA1_UART1_DCE_CTS_B 0x0AC 0x314 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD1_DATA1_UART1_DTE_RTS_B 0x0AC 0x314 0x4F0 0x4 0x5 +#define MX8MN_IOMUXC_SD1_DATA1_GPIO2_IO3 0x0AC 0x314 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x0B0 0x318 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD1_DATA2_ENET1_RGMII_RD0 0x0B0 0x318 0x57C 0x1 0x1 +#define MX8MN_IOMUXC_SD1_DATA2_UART2_DCE_TX 0x0B0 0x318 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD1_DATA2_UART2_DTE_RX 0x0B0 0x318 0x4FC 0x4 0x4 +#define MX8MN_IOMUXC_SD1_DATA2_GPIO2_IO4 0x0B0 0x318 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x0B4 0x31C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD1_DATA3_ENET1_RGMII_RD1 0x0B4 0x31C 0x554 0x1 0x1 +#define MX8MN_IOMUXC_SD1_DATA3_UART2_DCE_RX 0x0B4 0x31C 0x4FC 0x4 0x5 +#define MX8MN_IOMUXC_SD1_DATA3_UART2_DTE_TX 0x0B4 0x31C 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD1_DATA3_GPIO2_IO5 0x0B4 0x31C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x0B8 0x320 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD1_DATA4_ENET1_RGMII_TX_CTL 0x0B8 0x320 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SD1_DATA4_I2C1_SCL 0x0B8 0x320 0x55C 0x3 0x1 +#define MX8MN_IOMUXC_SD1_DATA4_UART2_DCE_RTS_B 0x0B8 0x320 0x4F8 0x4 0x4 +#define MX8MN_IOMUXC_SD1_DATA4_UART2_DTE_CTS_B 0x0B8 0x320 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD1_DATA4_GPIO2_IO6 0x0B8 0x320 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x0BC 0x324 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD1_DATA5_ENET1_TX_ER 0x0BC 0x324 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SD1_DATA5_I2C1_SDA 0x0BC 0x324 0x56C 0x3 0x1 +#define MX8MN_IOMUXC_SD1_DATA5_UART2_DCE_CTS_B 0x0BC 0x324 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD1_DATA5_UART2_DTE_RTS_B 0x0BC 0x324 0x4F8 0x4 0x5 +#define MX8MN_IOMUXC_SD1_DATA5_GPIO2_IO7 0x0BC 0x324 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x0C0 0x328 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD1_DATA6_ENET1_RGMII_RX_CTL 0x0C0 0x328 0x574 0x1 0x1 +#define MX8MN_IOMUXC_SD1_DATA6_I2C2_SCL 0x0C0 0x328 0x5D0 0x3 0x1 +#define MX8MN_IOMUXC_SD1_DATA6_UART3_DCE_TX 0x0C0 0x328 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD1_DATA6_UART3_DTE_RX 0x0C0 0x328 0x504 0x4 0x4 +#define MX8MN_IOMUXC_SD1_DATA6_GPIO2_IO8 0x0C0 0x328 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x0C4 0x32C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD1_DATA7_ENET1_RX_ER 0x0C4 0x32C 0x5C8 0x1 0x1 +#define MX8MN_IOMUXC_SD1_DATA7_I2C2_SDA 0x0C4 0x32C 0x560 0x3 0x1 +#define MX8MN_IOMUXC_SD1_DATA7_UART3_DCE_RX 0x0C4 0x32C 0x504 0x4 0x5 +#define MX8MN_IOMUXC_SD1_DATA7_UART3_DTE_TX 0x0C4 0x32C 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD1_DATA7_GPIO2_IO9 0x0C4 0x32C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x0C8 0x330 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD1_RESET_B_ENET1_TX_CLK 0x0C8 0x330 0x5A4 0x1 0x1 +#define MX8MN_IOMUXC_SD1_RESET_B_CCMSRCGPCMIX_ENET_REF_CLK_ROOT 0x0C8 0x330 0x5A4 0x1 0x0 +#define MX8MN_IOMUXC_SD1_RESET_B_I2C3_SCL 0x0C8 0x330 0x588 0x3 0x1 +#define MX8MN_IOMUXC_SD1_RESET_B_UART3_DCE_RTS_B 0x0C8 0x330 0x500 0x4 0x2 +#define MX8MN_IOMUXC_SD1_RESET_B_UART3_DTE_CTS_B 0x0C8 0x330 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x0C8 0x330 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x0CC 0x334 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD1_STROBE_I2C3_SDA 0x0CC 0x334 0x5BC 0x3 0x1 +#define MX8MN_IOMUXC_SD1_STROBE_UART3_DCE_CTS_B 0x0CC 0x334 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD1_STROBE_UART3_DTE_RTS_B 0x0CC 0x334 0x500 0x4 0x3 +#define MX8MN_IOMUXC_SD1_STROBE_GPIO2_IO11 0x0CC 0x334 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x0D0 0x338 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD2_CD_B_GPIO2_IO12 0x0D0 0x338 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD2_CD_B_CCMSRCGPCMIX_TESTER_ACK 0x0D0 0x338 0x000 0x6 0x0 +#define MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x0D4 0x33C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD2_CLK_SAI5_RX_SYNC 0x0D4 0x33C 0x4E4 0x1 0x1 +#define MX8MN_IOMUXC_SD2_CLK_ECSPI2_SCLK 0x0D4 0x33C 0x580 0x2 0x1 +#define MX8MN_IOMUXC_SD2_CLK_UART4_DCE_RX 0x0D4 0x33C 0x50C 0x3 0x4 +#define MX8MN_IOMUXC_SD2_CLK_UART4_DTE_TX 0x0D4 0x33C 0x000 0x3 0x0 +#define MX8MN_IOMUXC_SD2_CLK_SAI5_MCLK 0x0D4 0x33C 0x594 0x4 0x1 +#define MX8MN_IOMUXC_SD2_CLK_GPIO2_IO13 0x0D4 0x33C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD2_CLK_CCMSRCGPCMIX_OBSERVE0 0x0D4 0x33C 0x000 0x6 0x0 +#define MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x0D8 0x340 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD2_CMD_SAI5_RX_BCLK 0x0D8 0x340 0x4D0 0x1 0x1 +#define MX8MN_IOMUXC_SD2_CMD_ECSPI2_MOSI 0x0D8 0x340 0x590 0x2 0x1 +#define MX8MN_IOMUXC_SD2_CMD_UART4_DCE_TX 0x0D8 0x340 0x000 0x3 0x0 +#define MX8MN_IOMUXC_SD2_CMD_UART4_DTE_RX 0x0D8 0x340 0x50C 0x3 0x5 +#define MX8MN_IOMUXC_SD2_CMD_PDM_CLK 0x0D8 0x340 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SD2_CMD_GPIO2_IO14 0x0D8 0x340 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD2_CMD_CCMSRCGPCMIX_OBSERVE1 0x0D8 0x340 0x000 0x6 0x0 +#define MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x0DC 0x344 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD2_DATA0_SAI5_RX_DATA0 0x0DC 0x344 0x4D4 0x1 0x1 +#define MX8MN_IOMUXC_SD2_DATA0_I2C4_SDA 0x0DC 0x344 0x58C 0x2 0x1 +#define MX8MN_IOMUXC_SD2_DATA0_UART2_DCE_RX 0x0DC 0x344 0x4FC 0x3 0x6 +#define MX8MN_IOMUXC_SD2_DATA0_UART2_DTE_TX 0x0DC 0x344 0x000 0x3 0x0 +#define MX8MN_IOMUXC_SD2_DATA0_PDM_BIT_STREAM0 0x0DC 0x344 0x534 0x4 0x2 +#define MX8MN_IOMUXC_SD2_DATA0_GPIO2_IO15 0x0DC 0x344 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD2_DATA0_CCMSRCGPCMIX_OBSERVE2 0x0DC 0x344 0x000 0x6 0x0 +#define MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x0E0 0x348 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD2_DATA1_SAI5_TX_SYNC 0x0E0 0x348 0x4EC 0x1 0x1 +#define MX8MN_IOMUXC_SD2_DATA1_I2C4_SCL 0x0E0 0x348 0x5D4 0x2 0x1 +#define MX8MN_IOMUXC_SD2_DATA1_UART2_DCE_TX 0x0E0 0x348 0x000 0x3 0x0 +#define MX8MN_IOMUXC_SD2_DATA1_UART2_DTE_RX 0x0E0 0x348 0x4FC 0x3 0x7 +#define MX8MN_IOMUXC_SD2_DATA1_PDM_BIT_STREAM1 0x0E0 0x348 0x538 0x4 0x4 +#define MX8MN_IOMUXC_SD2_DATA1_GPIO2_IO16 0x0E0 0x348 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD2_DATA1_CCMSRCGPCMIX_WAIT 0x0E0 0x348 0x000 0x6 0x0 +#define MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x0E4 0x34C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD2_DATA2_SAI5_TX_BCLK 0x0E4 0x34C 0x4E8 0x1 0x1 +#define MX8MN_IOMUXC_SD2_DATA2_ECSPI2_SS0 0x0E4 0x34C 0x570 0x2 0x2 +#define MX8MN_IOMUXC_SD2_DATA2_SPDIF1_OUT 0x0E4 0x34C 0x000 0x3 0x0 +#define MX8MN_IOMUXC_SD2_DATA2_PDM_BIT_STREAM2 0x0E4 0x34C 0x53C 0x4 0x4 +#define MX8MN_IOMUXC_SD2_DATA2_GPIO2_IO17 0x0E4 0x34C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD2_DATA2_CCMSRCGPCMIX_STOP 0x0E4 0x34C 0x000 0x6 0x0 +#define MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x0E8 0x350 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD2_DATA3_SAI5_TX_DATA0 0x0E8 0x350 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SD2_DATA3_ECSPI2_MISO 0x0E8 0x350 0x578 0x2 0x1 +#define MX8MN_IOMUXC_SD2_DATA3_SPDIF1_IN 0x0E8 0x350 0x5CC 0x3 0x2 +#define MX8MN_IOMUXC_SD2_DATA3_PDM_BIT_STREAM3 0x0E8 0x350 0x540 0x4 0x4 +#define MX8MN_IOMUXC_SD2_DATA3_GPIO2_IO18 0x0E8 0x350 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD2_DATA3_CCMSRCGPCMIX_EARLY_RESET 0x0E8 0x350 0x000 0x6 0x0 +#define MX8MN_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0x0EC 0x354 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x0EC 0x354 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD2_RESET_B_CCMSRCGPCMIX_SYSTEM_RESET 0x0EC 0x354 0x000 0x6 0x0 +#define MX8MN_IOMUXC_SD2_WP_USDHC2_WP 0x0F0 0x358 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SD2_WP_GPIO2_IO20 0x0F0 0x358 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SD2_WP_CORESIGHT_EVENTI 0x0F0 0x358 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_ALE_RAWNAND_ALE 0x0F4 0x35C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x0F4 0x35C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_ALE_PDM_BIT_STREAM0 0x0F4 0x35C 0x534 0x3 0x3 +#define MX8MN_IOMUXC_NAND_ALE_UART3_DCE_RX 0x0F4 0x35C 0x504 0x4 0x6 +#define MX8MN_IOMUXC_NAND_ALE_UART3_DTE_TX 0x0F4 0x35C 0x000 0x4 0x0 +#define MX8MN_IOMUXC_NAND_ALE_GPIO3_IO0 0x0F4 0x35C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_ALE_CORESIGHT_TRACE_CLK 0x0F4 0x35C 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_CE0_B_RAWNAND_CE0_B 0x0F8 0x360 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x0F8 0x360 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_CE0_B_PDM_BIT_STREAM1 0x0F8 0x360 0x538 0x3 0x5 +#define MX8MN_IOMUXC_NAND_CE0_B_UART3_DCE_TX 0x0F8 0x360 0x000 0x4 0x0 +#define MX8MN_IOMUXC_NAND_CE0_B_UART3_DTE_RX 0x0F8 0x360 0x504 0x4 0x7 +#define MX8MN_IOMUXC_NAND_CE0_B_GPIO3_IO1 0x0F8 0x360 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_CE0_B_CORESIGHT_TRACE_CTL 0x0F8 0x360 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_CE1_B_RAWNAND_CE1_B 0x0FC 0x364 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_CE1_B_QSPI_A_SS1_B 0x0FC 0x364 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x0FC 0x364 0x59C 0x2 0x0 +#define MX8MN_IOMUXC_NAND_CE1_B_PDM_BIT_STREAM0 0x0FC 0x364 0x534 0x3 0x4 +#define MX8MN_IOMUXC_NAND_CE1_B_I2C4_SCL 0x0FC 0x364 0x5D4 0x4 0x2 +#define MX8MN_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x0FC 0x364 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_CE1_B_CORESIGHT_TRACE0 0x0FC 0x364 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_CE2_B_RAWNAND_CE2_B 0x100 0x368 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_CE2_B_QSPI_B_SS0_B 0x100 0x368 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x100 0x368 0x550 0x2 0x0 +#define MX8MN_IOMUXC_NAND_CE2_B_PDM_BIT_STREAM1 0x100 0x368 0x538 0x3 0x6 +#define MX8MN_IOMUXC_NAND_CE2_B_I2C4_SDA 0x100 0x368 0x58C 0x4 0x2 +#define MX8MN_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x100 0x368 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_CE2_B_CORESIGHT_TRACE1 0x100 0x368 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_CE3_B_RAWNAND_CE3_B 0x104 0x36C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_CE3_B_QSPI_B_SS1_B 0x104 0x36C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x104 0x36C 0x584 0x2 0x0 +#define MX8MN_IOMUXC_NAND_CE3_B_PDM_BIT_STREAM2 0x104 0x36C 0x53C 0x3 0x5 +#define MX8MN_IOMUXC_NAND_CE3_B_I2C3_SDA 0x104 0x36C 0x5BC 0x4 0x2 +#define MX8MN_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x104 0x36C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_CE3_B_CORESIGHT_TRACE2 0x104 0x36C 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_CLE_RAWNAND_CLE 0x108 0x370 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_CLE_QSPI_B_SCLK 0x108 0x370 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x108 0x370 0x54C 0x2 0x0 +#define MX8MN_IOMUXC_NAND_CLE_GPIO3_IO5 0x108 0x370 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_CLE_CORESIGHT_TRACE3 0x108 0x370 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_DATA00_RAWNAND_DATA00 0x10C 0x374 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x10C 0x374 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_DATA00_PDM_BIT_STREAM2 0x10C 0x374 0x53C 0x3 0x6 +#define MX8MN_IOMUXC_NAND_DATA00_UART4_DCE_RX 0x10C 0x374 0x50C 0x4 0x6 +#define MX8MN_IOMUXC_NAND_DATA00_UART4_DTE_TX 0x10C 0x374 0x000 0x4 0x0 +#define MX8MN_IOMUXC_NAND_DATA00_GPIO3_IO6 0x10C 0x374 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_DATA00_CORESIGHT_TRACE4 0x10C 0x374 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_DATA01_RAWNAND_DATA01 0x110 0x378 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x110 0x378 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_DATA01_PDM_BIT_STREAM3 0x110 0x378 0x540 0x3 0x5 +#define MX8MN_IOMUXC_NAND_DATA01_UART4_DCE_TX 0x110 0x378 0x000 0x4 0x0 +#define MX8MN_IOMUXC_NAND_DATA01_UART4_DTE_RX 0x110 0x378 0x50C 0x4 0x7 +#define MX8MN_IOMUXC_NAND_DATA01_GPIO3_IO7 0x110 0x378 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_DATA01_CORESIGHT_TRACE5 0x110 0x378 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_DATA02_RAWNAND_DATA02 0x114 0x37C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x114 0x37C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_DATA02_USDHC3_CD_B 0x114 0x37C 0x598 0x2 0x0 +#define MX8MN_IOMUXC_NAND_DATA02_I2C4_SDA 0x114 0x37C 0x58C 0x4 0x3 +#define MX8MN_IOMUXC_NAND_DATA02_GPIO3_IO8 0x114 0x37C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_DATA02_CORESIGHT_TRACE6 0x114 0x37C 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_DATA03_RAWNAND_DATA03 0x118 0x380 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x118 0x380 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_DATA03_USDHC3_WP 0x118 0x380 0x5B8 0x2 0x0 +#define MX8MN_IOMUXC_NAND_DATA03_GPIO3_IO9 0x118 0x380 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_DATA03_CORESIGHT_TRACE7 0x118 0x380 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_DATA04_RAWNAND_DATA04 0x11C 0x384 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_DATA04_QSPI_B_DATA0 0x11C 0x384 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x11C 0x384 0x5B4 0x2 0x0 +#define MX8MN_IOMUXC_NAND_DATA04_GPIO3_IO10 0x11C 0x384 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_DATA04_CORESIGHT_TRACE8 0x11C 0x384 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_DATA05_RAWNAND_DATA05 0x120 0x388 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_DATA05_QSPI_B_DATA1 0x120 0x388 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x120 0x388 0x5B0 0x2 0x0 +#define MX8MN_IOMUXC_NAND_DATA05_GPIO3_IO11 0x120 0x388 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_DATA05_CORESIGHT_TRACE9 0x120 0x388 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_DATA06_RAWNAND_DATA06 0x124 0x38C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_DATA06_QSPI_B_DATA2 0x124 0x38C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x124 0x38C 0x5E4 0x2 0x0 +#define MX8MN_IOMUXC_NAND_DATA06_GPIO3_IO12 0x124 0x38C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_DATA06_CORESIGHT_TRACE10 0x124 0x38C 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_DATA07_RAWNAND_DATA07 0x128 0x390 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_DATA07_QSPI_B_DATA3 0x128 0x390 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x128 0x390 0x5E0 0x2 0x0 +#define MX8MN_IOMUXC_NAND_DATA07_GPIO3_IO13 0x128 0x390 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_DATA07_CORESIGHT_TRACE11 0x128 0x390 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_DQS_RAWNAND_DQS 0x12C 0x394 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_DQS_QSPI_A_DQS 0x12C 0x394 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_DQS_PDM_CLK 0x12C 0x394 0x000 0x3 0x0 +#define MX8MN_IOMUXC_NAND_DQS_I2C3_SCL 0x12C 0x394 0x588 0x4 0x2 +#define MX8MN_IOMUXC_NAND_DQS_GPIO3_IO14 0x12C 0x394 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_DQS_CORESIGHT_TRACE12 0x12C 0x394 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_RE_B_RAWNAND_RE_B 0x130 0x398 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_RE_B_QSPI_B_DQS 0x130 0x398 0x000 0x1 0x0 +#define MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x130 0x398 0x558 0x2 0x0 +#define MX8MN_IOMUXC_NAND_RE_B_PDM_BIT_STREAM1 0x130 0x398 0x538 0x3 0x7 +#define MX8MN_IOMUXC_NAND_RE_B_GPIO3_IO15 0x130 0x398 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_RE_B_CORESIGHT_TRACE13 0x130 0x398 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_READY_B_RAWNAND_READY_B 0x134 0x39C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x134 0x39C 0x000 0x2 0x0 +#define MX8MN_IOMUXC_NAND_READY_B_PDM_BIT_STREAM3 0x134 0x39C 0x540 0x3 0x6 +#define MX8MN_IOMUXC_NAND_READY_B_I2C3_SCL 0x134 0x39C 0x588 0x4 0x3 +#define MX8MN_IOMUXC_NAND_READY_B_GPIO3_IO16 0x134 0x39C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_READY_B_CORESIGHT_TRACE14 0x134 0x39C 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_WE_B_RAWNAND_WE_B 0x138 0x3A0 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x138 0x3A0 0x5A0 0x2 0x0 +#define MX8MN_IOMUXC_NAND_WE_B_I2C3_SDA 0x138 0x3A0 0x5BC 0x4 0x3 +#define MX8MN_IOMUXC_NAND_WE_B_GPIO3_IO17 0x138 0x3A0 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_WE_B_CORESIGHT_TRACE15 0x138 0x3A0 0x000 0x6 0x0 +#define MX8MN_IOMUXC_NAND_WP_B_RAWNAND_WP_B 0x13C 0x3A4 0x000 0x0 0x0 +#define MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x13C 0x3A4 0x5DC 0x2 0x0 +#define MX8MN_IOMUXC_NAND_WP_B_I2C4_SDA 0x13C 0x3A4 0x58C 0x4 0x4 +#define MX8MN_IOMUXC_NAND_WP_B_GPIO3_IO18 0x13C 0x3A4 0x000 0x5 0x0 +#define MX8MN_IOMUXC_NAND_WP_B_CORESIGHT_EVENTO 0x13C 0x3A4 0x000 0x6 0x0 +#define MX8MN_IOMUXC_SAI5_RXFS_SAI5_RX_SYNC 0x140 0x3A8 0x4E4 0x0 0x0 +#define MX8MN_IOMUXC_SAI5_RXFS_GPIO3_IO19 0x140 0x3A8 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI5_RXC_SAI5_RX_BCLK 0x144 0x3AC 0x4D0 0x0 0x0 +#define MX8MN_IOMUXC_SAI5_RXC_PDM_CLK 0x144 0x3AC 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SAI5_RXC_GPIO3_IO20 0x144 0x3AC 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI5_RXD0_SAI5_RX_DATA0 0x148 0x3B0 0x4D4 0x0 0x0 +#define MX8MN_IOMUXC_SAI5_RXD0_PDM_BIT_STREAM0 0x148 0x3B0 0x534 0x4 0x0 +#define MX8MN_IOMUXC_SAI5_RXD0_GPIO3_IO21 0x148 0x3B0 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI5_RXD1_SAI5_RX_DATA1 0x14C 0x3B4 0x4D8 0x0 0x0 +#define MX8MN_IOMUXC_SAI5_RXD1_SAI5_TX_SYNC 0x14C 0x3B4 0x4EC 0x3 0x0 +#define MX8MN_IOMUXC_SAI5_RXD1_PDM_BIT_STREAM1 0x14C 0x3B4 0x538 0x4 0x0 +#define MX8MN_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x14C 0x3B4 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI5_RXD2_SAI5_RX_DATA2 0x150 0x3B8 0x4DC 0x0 0x0 +#define MX8MN_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK 0x150 0x3B8 0x4E8 0x3 0x0 +#define MX8MN_IOMUXC_SAI5_RXD2_PDM_BIT_STREAM2 0x150 0x3B8 0x53C 0x4 0x0 +#define MX8MN_IOMUXC_SAI5_RXD2_GPIO3_IO23 0x150 0x3B8 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI5_RXD3_SAI5_RX_DATA3 0x154 0x3BC 0x4E0 0x0 0x0 +#define MX8MN_IOMUXC_SAI5_RXD3_SAI5_TX_DATA0 0x154 0x3BC 0x000 0x3 0x0 +#define MX8MN_IOMUXC_SAI5_RXD3_PDM_BIT_STREAM3 0x154 0x3BC 0x540 0x4 0x0 +#define MX8MN_IOMUXC_SAI5_RXD3_GPIO3_IO24 0x154 0x3BC 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI5_MCLK_SAI5_MCLK 0x158 0x3C0 0x594 0x0 0x0 +#define MX8MN_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x158 0x3C0 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI2_RXFS_SAI2_RX_SYNC 0x1B0 0x418 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI2_RXFS_SAI5_TX_SYNC 0x1B0 0x418 0x4EC 0x1 0x2 +#define MX8MN_IOMUXC_SAI2_RXFS_SAI5_TX_DATA1 0x1B0 0x418 0x000 0x2 0x0 +#define MX8MN_IOMUXC_SAI2_RXFS_SAI2_RX_DATA1 0x1B0 0x418 0x5AC 0x3 0x0 +#define MX8MN_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x1B0 0x418 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SAI2_RXFS_UART1_DTE_RX 0x1B0 0x418 0x4F4 0x4 0x2 +#define MX8MN_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x1B0 0x418 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI2_RXFS_PDM_BIT_STREAM2 0x1B0 0x418 0x53C 0x6 0x7 +#define MX8MN_IOMUXC_SAI2_RXC_SAI2_RX_BCLK 0x1B4 0x41C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI2_RXC_SAI5_TX_BCLK 0x1B4 0x41C 0x4E8 0x1 0x2 +#define MX8MN_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x1B4 0x41C 0x4F4 0x4 0x3 +#define MX8MN_IOMUXC_SAI2_RXC_UART1_DTE_TX 0x1B4 0x41C 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SAI2_RXC_GPIO4_IO22 0x1B4 0x41C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI2_RXC_PDM_BIT_STREAM1 0x1B4 0x41C 0x538 0x6 0x8 +#define MX8MN_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0x1B8 0x420 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI2_RXD0_SAI5_TX_DATA0 0x1B8 0x420 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SAI2_RXD0_SAI2_TX_DATA1 0x1B8 0x420 0x000 0x3 0x0 +#define MX8MN_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x1B8 0x420 0x4F0 0x4 0x2 +#define MX8MN_IOMUXC_SAI2_RXD0_UART1_DTE_CTS_B 0x1B8 0x420 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SAI2_RXD0_GPIO4_IO23 0x1B8 0x420 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI2_RXD0_PDM_BIT_STREAM3 0x1B8 0x420 0x540 0x6 0x7 +#define MX8MN_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0x1BC 0x424 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI2_TXFS_SAI5_TX_DATA1 0x1BC 0x424 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SAI2_TXFS_SAI2_TX_DATA1 0x1BC 0x424 0x000 0x3 0x0 +#define MX8MN_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x1BC 0x424 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SAI2_TXFS_UART1_DTE_RTS_B 0x1BC 0x424 0x4F0 0x4 0x3 +#define MX8MN_IOMUXC_SAI2_TXFS_GPIO4_IO24 0x1BC 0x424 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI2_TXFS_PDM_BIT_STREAM2 0x1BC 0x424 0x53C 0x6 0x8 +#define MX8MN_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0x1C0 0x428 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI2_TXC_SAI5_TX_DATA2 0x1C0 0x428 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SAI2_TXC_GPIO4_IO25 0x1C0 0x428 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI2_TXC_PDM_BIT_STREAM1 0x1C0 0x428 0x538 0x6 0x9 +#define MX8MN_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0x1C4 0x42C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI2_TXD0_SAI5_TX_DATA3 0x1C4 0x42C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SAI2_TXD0_GPIO4_IO26 0x1C4 0x42C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI2_TXD0_CCMSRCGPCMIX_BOOT_MODE4 0x1C4 0x42C 0x540 0x6 0x8 +#define MX8MN_IOMUXC_SAI2_MCLK_SAI2_MCLK 0x1C8 0x430 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI2_MCLK_SAI5_MCLK 0x1C8 0x430 0x594 0x1 0x2 +#define MX8MN_IOMUXC_SAI2_MCLK_GPIO4_IO27 0x1C8 0x430 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI2_MCLK_SAI3_MCLK 0x1C8 0x430 0x5C0 0x6 0x1 +#define MX8MN_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0x1CC 0x434 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI3_RXFS_GPT1_CAPTURE1 0x1CC 0x434 0x5F0 0x1 0x0 +#define MX8MN_IOMUXC_SAI3_RXFS_SAI5_RX_SYNC 0x1CC 0x434 0x4E4 0x2 0x2 +#define MX8MN_IOMUXC_SAI3_RXFS_SAI3_RX_DATA1 0x1CC 0x434 0x000 0x3 0x0 +#define MX8MN_IOMUXC_SAI3_RXFS_SPDIF1_IN 0x1CC 0x434 0x5CC 0x4 0x3 +#define MX8MN_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x1CC 0x434 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI3_RXFS_PDM_BIT_STREAM0 0x1CC 0x434 0x534 0x6 0x5 +#define MX8MN_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x1D0 0x438 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI3_RXC_GPT1_CLK 0x1D0 0x438 0x5E8 0x1 0x0 +#define MX8MN_IOMUXC_SAI3_RXC_SAI5_RX_BCLK 0x1D0 0x438 0x4D0 0x2 0x2 +#define MX8MN_IOMUXC_SAI3_RXC_SAI2_RX_DATA1 0x1D0 0x438 0x5AC 0x3 0x2 +#define MX8MN_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x1D0 0x438 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SAI3_RXC_UART2_DTE_RTS_B 0x1D0 0x438 0x4F8 0x4 0x2 +#define MX8MN_IOMUXC_SAI3_RXC_GPIO4_IO29 0x1D0 0x438 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI3_RXC_PDM_CLK 0x1D0 0x438 0x000 0x6 0x0 +#define MX8MN_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x1D4 0x43C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI3_RXD_GPT1_COMPARE1 0x1D4 0x43C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SAI3_RXD_SAI5_RX_DATA0 0x1D4 0x43C 0x4D4 0x2 0x2 +#define MX8MN_IOMUXC_SAI3_RXD_SAI3_TX_DATA1 0x1D4 0x43C 0x000 0x3 0x0 +#define MX8MN_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x1D4 0x43C 0x4F8 0x4 0x3 +#define MX8MN_IOMUXC_SAI3_RXD_UART2_DTE_CTS_B 0x1D4 0x43C 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SAI3_RXD_GPIO4_IO30 0x1D4 0x43C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI3_RXD_PDM_BIT_STREAM1 0x1D4 0x43C 0x538 0x6 0x10 +#define MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x1D8 0x440 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI3_TXFS_GPT1_CAPTURE2 0x1D8 0x440 0x5EC 0x1 0x0 +#define MX8MN_IOMUXC_SAI3_TXFS_SAI5_RX_DATA1 0x1D8 0x440 0x4D8 0x2 0x1 +#define MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_DATA1 0x1D8 0x440 0x000 0x3 0x0 +#define MX8MN_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x1D8 0x440 0x4FC 0x4 0x2 +#define MX8MN_IOMUXC_SAI3_TXFS_UART2_DTE_TX 0x1D8 0x440 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SAI3_TXFS_GPIO4_IO31 0x1D8 0x440 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI3_TXFS_PDM_BIT_STREAM3 0x1D8 0x440 0x540 0x6 0x9 +#define MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x1DC 0x444 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI3_TXC_GPT1_COMPARE2 0x1DC 0x444 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SAI3_TXC_SAI5_RX_DATA2 0x1DC 0x444 0x4DC 0x2 0x1 +#define MX8MN_IOMUXC_SAI3_TXC_SAI2_TX_DATA1 0x1DC 0x444 0x000 0x3 0x0 +#define MX8MN_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x1DC 0x444 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SAI3_TXC_UART2_DTE_RX 0x1DC 0x444 0x4FC 0x4 0x3 +#define MX8MN_IOMUXC_SAI3_TXC_GPIO5_IO0 0x1DC 0x444 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI3_TXC_PDM_BIT_STREAM2 0x1DC 0x444 0x53C 0x6 0x9 +#define MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x1E0 0x448 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SAI3_TXD_GPT1_COMPARE3 0x1E0 0x448 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SAI3_TXD_SAI5_RX_DATA3 0x1E0 0x448 0x4E0 0x2 0x1 +#define MX8MN_IOMUXC_SAI3_TXD_SPDIF1_EXT_CLK 0x1E0 0x448 0x568 0x4 0x2 +#define MX8MN_IOMUXC_SAI3_TXD_GPIO5_IO1 0x1E0 0x448 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI3_TXD_CCMSRCGPCMIX_BOOT_MODE5 0x1E0 0x448 0x000 0x6 0x0 +#define MX8MN_IOMUXC_SAI3_MCLK_SAI3_MCLK 0x1E4 0x44C 0x5C0 0x0 0x0 +#define MX8MN_IOMUXC_SAI3_MCLK_PWM4_OUT 0x1E4 0x44C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SAI3_MCLK_SAI5_MCLK 0x1E4 0x44C 0x594 0x2 0x3 +#define MX8MN_IOMUXC_SAI3_MCLK_SPDIF1_OUT 0x1E4 0x44C 0x000 0x4 0x0 +#define MX8MN_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x1E4 0x44C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SAI3_MCLK_SPDIF1_IN 0x1E4 0x44C 0x5CC 0x6 0x4 +#define MX8MN_IOMUXC_SPDIF_TX_SPDIF1_OUT 0x1E8 0x450 0x000 0x0 0x0 +#define MX8MN_IOMUXC_SPDIF_TX_PWM3_OUT 0x1E8 0x450 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SPDIF_TX_GPIO5_IO3 0x1E8 0x450 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SPDIF_RX_SPDIF1_IN 0x1EC 0x454 0x5CC 0x0 0x0 +#define MX8MN_IOMUXC_SPDIF_RX_PWM2_OUT 0x1EC 0x454 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SPDIF_RX_GPIO5_IO4 0x1EC 0x454 0x000 0x5 0x0 +#define MX8MN_IOMUXC_SPDIF_EXT_CLK_SPDIF1_EXT_CLK 0x1F0 0x458 0x568 0x0 0x0 +#define MX8MN_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT 0x1F0 0x458 0x000 0x1 0x0 +#define MX8MN_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x1F0 0x458 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x1F4 0x45C 0x5D8 0x0 0x0 +#define MX8MN_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX 0x1F4 0x45C 0x504 0x1 0x0 +#define MX8MN_IOMUXC_ECSPI1_SCLK_UART3_DTE_TX 0x1F4 0x45C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_ECSPI1_SCLK_I2C1_SCL 0x1F4 0x45C 0x55C 0x2 0x2 +#define MX8MN_IOMUXC_ECSPI1_SCLK_SAI5_RX_SYNC 0x1F4 0x45C 0x4DC 0x3 0x2 +#define MX8MN_IOMUXC_ECSPI1_SCLK_GPIO5_IO6 0x1F4 0x45C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x1F8 0x460 0x5A8 0x0 0x0 +#define MX8MN_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX 0x1F8 0x460 0x000 0x1 0x0 +#define MX8MN_IOMUXC_ECSPI1_MOSI_UART3_DTE_RX 0x1F8 0x460 0x504 0x1 0x1 +#define MX8MN_IOMUXC_ECSPI1_MOSI_I2C1_SDA 0x1F8 0x460 0x56C 0x2 0x2 +#define MX8MN_IOMUXC_ECSPI1_MOSI_SAI5_RX_BCLK 0x1F8 0x460 0x4D0 0x3 0x3 +#define MX8MN_IOMUXC_ECSPI1_MOSI_GPIO5_IO7 0x1F8 0x460 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x1FC 0x464 0x5C4 0x0 0x0 +#define MX8MN_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x1FC 0x464 0x000 0x1 0x0 +#define MX8MN_IOMUXC_ECSPI1_MISO_UART3_DTE_RTS_B 0x1FC 0x464 0x500 0x1 0x0 +#define MX8MN_IOMUXC_ECSPI1_MISO_I2C2_SCL 0x1FC 0x464 0x5D0 0x2 0x2 +#define MX8MN_IOMUXC_ECSPI1_MISO_SAI5_RX_DATA0 0x1FC 0x464 0x4D4 0x3 0x3 +#define MX8MN_IOMUXC_ECSPI1_MISO_GPIO5_IO8 0x1FC 0x464 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ECSPI1_SS0_ECSPI1_SS0 0x200 0x468 0x564 0x0 0x0 +#define MX8MN_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x200 0x468 0x500 0x1 0x1 +#define MX8MN_IOMUXC_ECSPI1_SS0_UART3_DTE_CTS_B 0x200 0x468 0x000 0x1 0x0 +#define MX8MN_IOMUXC_ECSPI1_SS0_I2C2_SDA 0x200 0x468 0x560 0x2 0x2 +#define MX8MN_IOMUXC_ECSPI1_SS0_SAI5_RX_DATA1 0x200 0x468 0x4D8 0x3 0x2 +#define MX8MN_IOMUXC_ECSPI1_SS0_SAI5_TX_SYNC 0x200 0x468 0x4EC 0x4 0x3 +#define MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x200 0x468 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x204 0x46C 0x580 0x0 0x0 +#define MX8MN_IOMUXC_ECSPI2_SCLK_UART4_DCE_RX 0x204 0x46C 0x50C 0x1 0x0 +#define MX8MN_IOMUXC_ECSPI2_SCLK_UART4_DTE_TX 0x204 0x46C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_ECSPI2_SCLK_I2C3_SCL 0x204 0x46C 0x588 0x2 0x4 +#define MX8MN_IOMUXC_ECSPI2_SCLK_SAI5_RX_DATA2 0x204 0x46C 0x000 0x3 0x0 +#define MX8MN_IOMUXC_ECSPI2_SCLK_SAI5_TX_BCLK 0x204 0x46C 0x4E8 0x4 0x3 +#define MX8MN_IOMUXC_ECSPI2_SCLK_GPIO5_IO10 0x204 0x46C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x208 0x470 0x590 0x0 0x0 +#define MX8MN_IOMUXC_ECSPI2_MOSI_UART4_DCE_TX 0x208 0x470 0x000 0x1 0x0 +#define MX8MN_IOMUXC_ECSPI2_MOSI_UART4_DTE_RX 0x208 0x470 0x50C 0x1 0x1 +#define MX8MN_IOMUXC_ECSPI2_MOSI_I2C3_SDA 0x208 0x470 0x5BC 0x2 0x4 +#define MX8MN_IOMUXC_ECSPI2_MOSI_SAI5_RX_DATA3 0x208 0x470 0x4E0 0x3 0x2 +#define MX8MN_IOMUXC_ECSPI2_MOSI_SAI5_TX_DATA0 0x208 0x470 0x000 0x4 0x0 +#define MX8MN_IOMUXC_ECSPI2_MOSI_GPIO5_IO11 0x208 0x470 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x20C 0x474 0x578 0x0 0x0 +#define MX8MN_IOMUXC_ECSPI2_MISO_UART4_DCE_CTS_B 0x20C 0x474 0x000 0x1 0x0 +#define MX8MN_IOMUXC_ECSPI2_MISO_UART4_DTE_RTS_B 0x20C 0x474 0x508 0x1 0x0 +#define MX8MN_IOMUXC_ECSPI2_MISO_I2C4_SCL 0x20C 0x474 0x5D4 0x2 0x3 +#define MX8MN_IOMUXC_ECSPI2_MISO_SAI5_MCLK 0x20C 0x474 0x594 0x3 0x4 +#define MX8MN_IOMUXC_ECSPI2_MISO_GPIO5_IO12 0x20C 0x474 0x000 0x5 0x0 +#define MX8MN_IOMUXC_ECSPI2_SS0_ECSPI2_SS0 0x210 0x478 0x570 0x0 0x0 +#define MX8MN_IOMUXC_ECSPI2_SS0_UART4_DCE_RTS_B 0x210 0x478 0x508 0x1 0x1 +#define MX8MN_IOMUXC_ECSPI2_SS0_UART4_DTE_CTS_B 0x210 0x478 0x000 0x1 0x0 +#define MX8MN_IOMUXC_ECSPI2_SS0_I2C4_SDA 0x210 0x478 0x58C 0x2 0x5 +#define MX8MN_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x210 0x478 0x000 0x5 0x0 +#define MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x214 0x47C 0x55C 0x0 0x0 +#define MX8MN_IOMUXC_I2C1_SCL_ENET1_MDC 0x214 0x47C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_I2C1_SCL_ECSPI1_SCLK 0x214 0x47C 0x5D8 0x3 0x1 +#define MX8MN_IOMUXC_I2C1_SCL_GPIO5_IO14 0x214 0x47C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x218 0x480 0x56C 0x0 0x0 +#define MX8MN_IOMUXC_I2C1_SDA_ENET1_MDIO 0x218 0x480 0x4C0 0x1 0x2 +#define MX8MN_IOMUXC_I2C1_SDA_ECSPI1_MOSI 0x218 0x480 0x5A8 0x3 0x1 +#define MX8MN_IOMUXC_I2C1_SDA_GPIO5_IO15 0x218 0x480 0x000 0x5 0x0 +#define MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL 0x21C 0x484 0x5D0 0x0 0x0 +#define MX8MN_IOMUXC_I2C2_SCL_ENET1_1588_EVENT1_IN 0x21C 0x484 0x000 0x1 0x0 +#define MX8MN_IOMUXC_I2C2_SCL_USDHC3_CD_B 0x21C 0x484 0x598 0x2 0x1 +#define MX8MN_IOMUXC_I2C2_SCL_ECSPI1_MISO 0x21C 0x484 0x5C4 0x3 0x1 +#define MX8MN_IOMUXC_I2C2_SCL_GPIO5_IO16 0x21C 0x484 0x000 0x5 0x0 +#define MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA 0x220 0x488 0x560 0x0 0x0 +#define MX8MN_IOMUXC_I2C2_SDA_ENET1_1588_EVENT1_OUT 0x220 0x488 0x000 0x1 0x0 +#define MX8MN_IOMUXC_I2C2_SDA_USDHC3_WP 0x220 0x488 0x5B8 0x2 0x1 +#define MX8MN_IOMUXC_I2C2_SDA_ECSPI1_SS0 0x220 0x488 0x564 0x3 0x1 +#define MX8MN_IOMUXC_I2C2_SDA_GPIO5_IO17 0x220 0x488 0x000 0x5 0x0 +#define MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL 0x224 0x48C 0x588 0x0 0x0 +#define MX8MN_IOMUXC_I2C3_SCL_PWM4_OUT 0x224 0x48C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_I2C3_SCL_GPT2_CLK 0x224 0x48C 0x000 0x2 0x0 +#define MX8MN_IOMUXC_I2C3_SCL_ECSPI2_SCLK 0x224 0x48C 0x580 0x3 0x2 +#define MX8MN_IOMUXC_I2C3_SCL_GPIO5_IO18 0x224 0x48C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA 0x228 0x490 0x5BC 0x0 0x0 +#define MX8MN_IOMUXC_I2C3_SDA_PWM3_OUT 0x228 0x490 0x000 0x1 0x0 +#define MX8MN_IOMUXC_I2C3_SDA_GPT3_CLK 0x228 0x490 0x000 0x2 0x0 +#define MX8MN_IOMUXC_I2C3_SDA_ECSPI2_MOSI 0x228 0x490 0x590 0x3 0x2 +#define MX8MN_IOMUXC_I2C3_SDA_GPIO5_IO19 0x228 0x490 0x000 0x5 0x0 +#define MX8MN_IOMUXC_I2C4_SCL_I2C4_SCL 0x22C 0x494 0x5D4 0x0 0x0 +#define MX8MN_IOMUXC_I2C4_SCL_PWM2_OUT 0x22C 0x494 0x000 0x1 0x0 +#define MX8MN_IOMUXC_I2C4_SCL_ECSPI2_MISO 0x22C 0x494 0x578 0x3 0x2 +#define MX8MN_IOMUXC_I2C4_SCL_GPIO5_IO20 0x22C 0x494 0x000 0x5 0x0 +#define MX8MN_IOMUXC_I2C4_SDA_I2C4_SDA 0x230 0x498 0x58C 0x0 0x0 +#define MX8MN_IOMUXC_I2C4_SDA_PWM1_OUT 0x230 0x498 0x000 0x1 0x0 +#define MX8MN_IOMUXC_I2C4_SDA_ECSPI2_SS0 0x230 0x498 0x570 0x3 0x1 +#define MX8MN_IOMUXC_I2C4_SDA_GPIO5_IO21 0x230 0x498 0x000 0x5 0x0 +#define MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x234 0x49C 0x4F4 0x0 0x0 +#define MX8MN_IOMUXC_UART1_RXD_UART1_DTE_TX 0x234 0x49C 0x000 0x0 0x0 +#define MX8MN_IOMUXC_UART1_RXD_ECSPI3_SCLK 0x234 0x49C 0x000 0x1 0x0 +#define MX8MN_IOMUXC_UART1_RXD_GPIO5_IO22 0x234 0x49C 0x000 0x5 0x0 +#define MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x238 0x4A0 0x000 0x0 0x0 +#define MX8MN_IOMUXC_UART1_TXD_UART1_DTE_RX 0x238 0x4A0 0x4F4 0x0 0x1 +#define MX8MN_IOMUXC_UART1_TXD_ECSPI3_MOSI 0x238 0x4A0 0x000 0x1 0x0 +#define MX8MN_IOMUXC_UART1_TXD_GPIO5_IO23 0x238 0x4A0 0x000 0x5 0x0 +#define MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x23C 0x4A4 0x4FC 0x0 0x0 +#define MX8MN_IOMUXC_UART2_RXD_UART2_DTE_TX 0x23C 0x4A4 0x000 0x0 0x0 +#define MX8MN_IOMUXC_UART2_RXD_ECSPI3_MISO 0x23C 0x4A4 0x000 0x1 0x0 +#define MX8MN_IOMUXC_UART2_RXD_GPT1_COMPARE3 0x23C 0x4A4 0x000 0x3 0x0 +#define MX8MN_IOMUXC_UART2_RXD_GPIO5_IO24 0x23C 0x4A4 0x000 0x5 0x0 +#define MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x240 0x4A8 0x000 0x0 0x0 +#define MX8MN_IOMUXC_UART2_TXD_UART2_DTE_RX 0x240 0x4A8 0x4FC 0x0 0x1 +#define MX8MN_IOMUXC_UART2_TXD_ECSPI3_SS0 0x240 0x4A8 0x000 0x1 0x0 +#define MX8MN_IOMUXC_UART2_TXD_GPT1_COMPARE2 0x240 0x4A8 0x000 0x3 0x0 +#define MX8MN_IOMUXC_UART2_TXD_GPIO5_IO25 0x240 0x4A8 0x000 0x5 0x0 +#define MX8MN_IOMUXC_UART3_RXD_UART3_DCE_RX 0x244 0x4AC 0x504 0x0 0x2 +#define MX8MN_IOMUXC_UART3_RXD_UART3_DTE_TX 0x244 0x4AC 0x000 0x0 0x0 +#define MX8MN_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x244 0x4AC 0x000 0x1 0x0 +#define MX8MN_IOMUXC_UART3_RXD_UART1_DTE_RTS_B 0x244 0x4AC 0x4F0 0x1 0x0 +#define MX8MN_IOMUXC_UART3_RXD_USDHC3_RESET_B 0x244 0x4AC 0x000 0x2 0x0 +#define MX8MN_IOMUXC_UART3_RXD_GPT1_CAPTURE2 0x244 0x4AC 0x5EC 0x3 0x1 +#define MX8MN_IOMUXC_UART3_RXD_GPIO5_IO26 0x244 0x4AC 0x000 0x5 0x0 +#define MX8MN_IOMUXC_UART3_TXD_UART3_DCE_TX 0x248 0x4B0 0x000 0x0 0x0 +#define MX8MN_IOMUXC_UART3_TXD_UART3_DTE_RX 0x248 0x4B0 0x504 0x0 0x3 +#define MX8MN_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x248 0x4B0 0x4F0 0x1 0x1 +#define MX8MN_IOMUXC_UART3_TXD_UART1_DTE_CTS_B 0x248 0x4B0 0x000 0x1 0x0 +#define MX8MN_IOMUXC_UART3_TXD_USDHC3_VSELECT 0x248 0x4B0 0x000 0x2 0x0 +#define MX8MN_IOMUXC_UART3_TXD_GPT1_CLK 0x248 0x4B0 0x5E8 0x3 0x1 +#define MX8MN_IOMUXC_UART3_TXD_GPIO5_IO27 0x248 0x4B0 0x000 0x5 0x0 +#define MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX 0x24C 0x4B4 0x50C 0x0 0x2 +#define MX8MN_IOMUXC_UART4_RXD_UART4_DTE_TX 0x24C 0x4B4 0x000 0x0 0x0 +#define MX8MN_IOMUXC_UART4_RXD_UART2_DCE_CTS_B 0x24C 0x4B4 0x000 0x1 0x0 +#define MX8MN_IOMUXC_UART4_RXD_UART2_DTE_RTS_B 0x24C 0x4B4 0x4F8 0x1 0x0 +#define MX8MN_IOMUXC_UART4_RXD_GPT1_COMPARE1 0x24C 0x4B4 0x000 0x3 0x0 +#define MX8MN_IOMUXC_UART4_RXD_GPIO5_IO28 0x24C 0x4B4 0x000 0x5 0x0 +#define MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX 0x250 0x4B8 0x000 0x0 0x0 +#define MX8MN_IOMUXC_UART4_TXD_UART4_DTE_RX 0x250 0x4B8 0x50C 0x0 0x3 +#define MX8MN_IOMUXC_UART4_TXD_UART2_DCE_RTS_B 0x250 0x4B8 0x4F8 0x1 0x1 +#define MX8MN_IOMUXC_UART4_TXD_UART2_DTE_CTS_B 0x250 0x4B8 0x000 0x1 0x0 +#define MX8MN_IOMUXC_UART4_TXD_GPT1_CAPTURE1 0x250 0x4B8 0x5F0 0x3 0x1 +#define MX8MN_IOMUXC_UART4_TXD_GPIO5_IO29 0x250 0x4B8 0x000 0x5 0x0 + +#endif /* __DTS_IMX8MN_PINFUNC_H */ -- cgit v1.2.3 From 7b34b0032bae3c6dac2ddd87fbb356489acda517 Mon Sep 17 00:00:00 2001 From: Chris Packham Date: Tue, 18 Jun 2019 09:54:55 +1200 Subject: dt-bindings: pinctrl: mvebu: Document bindings for 98DX1135 The 98DX1135 is similar to the 98DX4122 except the MPP options differ. Signed-off-by: Chris Packham Reviewed-by: Andrew Lunn Signed-off-by: Linus Walleij --- .../bindings/pinctrl/marvell,kirkwood-pinctrl.txt | 44 +++++++++++++++++++++- 1 file changed, 42 insertions(+), 2 deletions(-) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt index 6c0ea155b708..2932f171ee85 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt @@ -6,8 +6,8 @@ part and usage. Required properties: - compatible: "marvell,88f6180-pinctrl", "marvell,88f6190-pinctrl", "marvell,88f6192-pinctrl", - "marvell,88f6281-pinctrl", "marvell,88f6282-pinctrl" - "marvell,98dx4122-pinctrl" + "marvell,88f6281-pinctrl", "marvell,88f6282-pinctrl", + "marvell,98dx4122-pinctrl", "marvell,98dx1135-pinctrl" - reg: register specifier of MPP registers This driver supports all kirkwood variants, i.e. 88f6180, 88f619x, and 88f628x. @@ -317,3 +317,43 @@ mpp44 44 gpio mpp45 45 gpio mpp49 49 gpio +* Marvell Poncat2 98dx1135 + +name pins functions +================================================================================ + +mpp0 0 gpio, nand(io2), spi(cs) +mpp1 1 gpo, nand(io3), spi(mosi) +mpp2 2 gpo, nand(io4), spi(sck) +mpp3 3 gpo, nand(io5), spi(miso) +mpp4 4 gpio, nand(io6), uart0(rxd) +mpp5 5 gpo, nand(io7), uart0(txd) +mpp6 6 sysrst(out) +mpp7 7 gpo, spi(cs) +mpp8 8 gpio, twsi0(sda), uart1(rts) +mpp9 9 gpio, twsi(sck), uart1(cts) +mpp10 10 gpo, uart0(txd) +mpp11 11 gpio, uart0(rxd) +mpp13 13 gpio, uart1(txd) +mpp14 14 gpio, uart1(rxd) +mpp15 15 gpio, uart0(rts) +mpp16 16 gpio, uart0(cts) +mpp17 17 gpio, nand(cle) +mpp18 18 gpo, nand(io0) +mpp19 19 gpo, nand(io1) +mpp20 20 gpio +mpp21 21 gpio +mpp22 22 gpio +mpp23 23 gpio +mpp24 24 gpio +mpp25 25 gpio +mpp26 26 gpio +mpp27 27 gpio +mpp28 28 gpio, nand(ren) +mpp29 29 gpio, nand(wen) +mpp30 30 gpio +mpp31 31 gpio +mpp32 32 gpio +mpp33 33 gpio +mpp34 34 gpio, nand(ale) +mpp35 35 gpio, nand(cen) -- cgit v1.2.3 From 34ae69998b665073bf27085e60b52329cf169e0d Mon Sep 17 00:00:00 2001 From: Andrew Jeffery Date: Fri, 28 Jun 2019 12:08:31 +0930 Subject: dt-bindings: pinctrl: aspeed: Split bindings document in two Have one for each of the AST2400 and AST2500. The only thing that was common was the fact that both support ASPEED BMC SoCs. Cc: Johnny Huang Signed-off-by: Andrew Jeffery Acked-by: Joel Stanley Link: https://lore.kernel.org/r/20190628023838.15426-2-andrew@aj.id.au Signed-off-by: Linus Walleij --- .../bindings/pinctrl/aspeed,ast2400-pinctrl.txt | 80 ++++++++++ .../bindings/pinctrl/aspeed,ast2500-pinctrl.txt | 119 ++++++++++++++ .../devicetree/bindings/pinctrl/pinctrl-aspeed.txt | 172 --------------------- 3 files changed, 199 insertions(+), 172 deletions(-) create mode 100644 Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.txt delete mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.txt new file mode 100644 index 000000000000..67e0325ccf2e --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.txt @@ -0,0 +1,80 @@ +============================= +Aspeed AST2400 Pin Controller +============================= + +Required properties for the AST2400: +- compatible : Should be one of the following: + "aspeed,ast2400-pinctrl" + "aspeed,g4-pinctrl" + +The pin controller node should be the child of a syscon node with the required +property: + +- compatible : Should be one of the following: + "aspeed,ast2400-scu", "syscon", "simple-mfd" + "aspeed,g4-scu", "syscon", "simple-mfd" + +Refer to the the bindings described in +Documentation/devicetree/bindings/mfd/syscon.txt + +Subnode Format +============== + +The required properties of pinmux child nodes are: +- function: the mux function to select +- groups : the list of groups to select with this function + +Required properties of pinconf child nodes are: +- groups: A list of groups to select (either this or "pins" must be + specified) +- pins : A list of ball names as strings, eg "D14" (either this or "groups" + must be specified) + +Optional properties of pinconf child nodes are: +- bias-disable : disable any pin bias +- bias-pull-down: pull down the pin +- drive-strength: sink or source at most X mA + +Definitions are as specified in +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt, with any +further limitations as described above. + +For pinmux, each mux function has only one associated pin group. Each group is +named by its function. The following values for the function and groups +properties are supported: + +ACPI ADC0 ADC1 ADC10 ADC11 ADC12 ADC13 ADC14 ADC15 ADC2 ADC3 ADC4 ADC5 ADC6 +ADC7 ADC8 ADC9 BMCINT DDCCLK DDCDAT EXTRST FLACK FLBUSY FLWP GPID GPID0 GPID2 +GPID4 GPID6 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 +I2C5 I2C6 I2C7 I2C8 I2C9 LPCPD LPCPME LPCRST LPCSMI MAC1LINK MAC2LINK MDIO1 +MDIO2 NCTS1 NCTS2 NCTS3 NCTS4 NDCD1 NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 +NDTR1 NDTR2 NDTR3 NDTR4 NDTS4 NRI1 NRI2 NRI3 NRI4 NRTS1 NRTS2 NRTS3 OSCCLK PWM0 +PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 ROM16 ROM8 ROMCS1 +ROMCS2 ROMCS3 ROMCS4 RXD1 RXD2 RXD3 RXD4 SALT1 SALT2 SALT3 SALT4 SD1 SD2 SGPMCK +SGPMI SGPMLD SGPMO SGPSCK SGPSI0 SGPSI1 SGPSLD SIOONCTRL SIOPBI SIOPBO SIOPWREQ +SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1DEBUG SPI1PASSTHRU SPICS1 TIMER3 TIMER4 +TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 TXD3 TXD4 UART6 USB11D1 USB11H2 USB2D1 +USB2H1 USBCKI VGABIOS_ROM VGAHS VGAVS VPI18 VPI24 VPI30 VPO12 VPO24 WDTRST1 +WDTRST2 + +Example +======= + +syscon: scu@1e6e2000 { + compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; + + pinctrl: pinctrl { + compatible = "aspeed,g4-pinctrl"; + + pinctrl_i2c3_default: i2c3_default { + function = "I2C3"; + groups = "I2C3"; + }; + + pinctrl_gpioh0_unbiased_default: gpioh0 { + pins = "A8"; + bias-disable; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.txt new file mode 100644 index 000000000000..ca7025dc1901 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.txt @@ -0,0 +1,119 @@ +============================= +Aspeed AST2500 Pin Controller +============================= + +Required properties for g5: +- compatible : Should be one of the following: + "aspeed,ast2500-pinctrl" + "aspeed,g5-pinctrl" + +- aspeed,external-nodes: A cell of phandles to external controller nodes: + 0: compatible with "aspeed,ast2500-gfx", "syscon" + 1: compatible with "aspeed,ast2500-lhc", "syscon" + +The pin controller node should be the child of a syscon node with the required +property: + +- compatible : Should be one of the following: + "aspeed,ast2500-scu", "syscon", "simple-mfd" + "aspeed,g5-scu", "syscon", "simple-mfd" + +Refer to the the bindings described in +Documentation/devicetree/bindings/mfd/syscon.txt + +Subnode Format +============== + +The required properties of pinmux child nodes are: +- function: the mux function to select +- groups : the list of groups to select with this function + +Required properties of pinconf child nodes are: +- groups: A list of groups to select (either this or "pins" must be + specified) +- pins : A list of ball names as strings, eg "D14" (either this or "groups" + must be specified) + +Optional properties of pinconf child nodes are: +- bias-disable : disable any pin bias +- bias-pull-down: pull down the pin +- drive-strength: sink or source at most X mA + +Definitions are as specified in +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt, with any +further limitations as described above. + +For pinmux, each mux function has only one associated pin group. Each group is +named by its function. The following values for the function and groups +properties are supported: + +ACPI ADC0 ADC1 ADC10 ADC11 ADC12 ADC13 ADC14 ADC15 ADC2 ADC3 ADC4 ADC5 ADC6 +ADC7 ADC8 ADC9 BMCINT DDCCLK DDCDAT ESPI FWSPICS1 FWSPICS2 GPID0 GPID2 GPID4 +GPID6 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 +I2C7 I2C8 I2C9 LAD0 LAD1 LAD2 LAD3 LCLK LFRAME LPCHC LPCPD LPCPLUS LPCPME +LPCRST LPCSMI LSIRQ MAC1LINK MAC2LINK MDIO1 MDIO2 NCTS1 NCTS2 NCTS3 NCTS4 NDCD1 +NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 NDTR1 NDTR2 NDTR3 NDTR4 NRI1 NRI2 +NRI3 NRI4 NRTS1 NRTS2 NRTS3 NRTS4 OSCCLK PEWAKE PNOR PWM0 PWM1 PWM2 PWM3 PWM4 +PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 RXD1 RXD2 RXD3 RXD4 SALT1 SALT10 +SALT11 SALT12 SALT13 SALT14 SALT2 SALT3 SALT4 SALT5 SALT6 SALT7 SALT8 SALT9 +SCL1 SCL2 SD1 SD2 SDA1 SDA2 SGPM SGPS1 SGPS2 SIOONCTRL SIOPBI SIOPBO SIOPWREQ +SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1CS1 SPI1DEBUG SPI1PASSTHRU SPI2CK SPI2CS0 +SPI2CS1 SPI2MISO SPI2MOSI TIMER3 TIMER4 TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 +TXD3 TXD4 UART6 USB11BHID USB2AD USB2AH USB2BD USB2BH USBCKI VGABIOSROM VGAHS +VGAVS VPI24 VPO WDTRST1 WDTRST2 + +Example +======= + +ahb { + apb { + syscon: scu@1e6e2000 { + compatible = "aspeed,ast2500-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; + + pinctrl: pinctrl { + compatible = "aspeed,g5-pinctrl"; + aspeed,external-nodes = <&gfx &lhc>; + + pinctrl_i2c3_default: i2c3_default { + function = "I2C3"; + groups = "I2C3"; + }; + + pinctrl_gpioh0_unbiased_default: gpioh0 { + pins = "A18"; + bias-disable; + }; + }; + }; + + gfx: display@1e6e6000 { + compatible = "aspeed,ast2500-gfx", "syscon"; + reg = <0x1e6e6000 0x1000>; + }; + }; + + lpc: lpc@1e789000 { + compatible = "aspeed,ast2500-lpc", "simple-mfd"; + reg = <0x1e789000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x1e789000 0x1000>; + + lpc_host: lpc-host@80 { + compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon"; + reg = <0x80 0x1e0>; + reg-io-width = <4>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x80 0x1e0>; + + lhc: lhc@20 { + compatible = "aspeed,ast2500-lhc"; + reg = <0x20 0x24 0x48 0x8>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt deleted file mode 100644 index 8f1c5c4d62f9..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt +++ /dev/null @@ -1,172 +0,0 @@ -====================== -Aspeed Pin Controllers -====================== - -The Aspeed SoCs vary in functionality inside a generation but have a common mux -device register layout. - -Required properties for g4: -- compatible : Should be one of the following: - "aspeed,ast2400-pinctrl" - "aspeed,g4-pinctrl" - -Required properties for g5: -- compatible : Should be one of the following: - "aspeed,ast2500-pinctrl" - "aspeed,g5-pinctrl" - -- aspeed,external-nodes: A cell of phandles to external controller nodes: - 0: compatible with "aspeed,ast2500-gfx", "syscon" - 1: compatible with "aspeed,ast2500-lhc", "syscon" - -The pin controller node should be the child of a syscon node with the required -property: - -- compatible : Should be one of the following: - "aspeed,ast2400-scu", "syscon", "simple-mfd" - "aspeed,g4-scu", "syscon", "simple-mfd" - "aspeed,ast2500-scu", "syscon", "simple-mfd" - "aspeed,g5-scu", "syscon", "simple-mfd" - -Refer to the the bindings described in -Documentation/devicetree/bindings/mfd/syscon.txt - -Subnode Format -============== - -The required properties of pinmux child nodes are: -- function: the mux function to select -- groups : the list of groups to select with this function - -Required properties of pinconf child nodes are: -- groups: A list of groups to select (either this or "pins" must be - specified) -- pins : A list of ball names as strings, eg "D14" (either this or "groups" - must be specified) - -Optional properties of pinconf child nodes are: -- bias-disable : disable any pin bias -- bias-pull-down: pull down the pin -- drive-strength: sink or source at most X mA - -Definitions are as specified in -Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt, with any -further limitations as described above. - -For pinmux, each mux function has only one associated pin group. Each group is -named by its function. The following values for the function and groups -properties are supported: - -aspeed,ast2400-pinctrl, aspeed,g4-pinctrl: - -ACPI ADC0 ADC1 ADC10 ADC11 ADC12 ADC13 ADC14 ADC15 ADC2 ADC3 ADC4 ADC5 ADC6 -ADC7 ADC8 ADC9 BMCINT DDCCLK DDCDAT EXTRST FLACK FLBUSY FLWP GPID GPID0 GPID2 -GPID4 GPID6 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 -I2C5 I2C6 I2C7 I2C8 I2C9 LPCPD LPCPME LPCRST LPCSMI MAC1LINK MAC2LINK MDIO1 -MDIO2 NCTS1 NCTS2 NCTS3 NCTS4 NDCD1 NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 -NDTR1 NDTR2 NDTR3 NDTR4 NDTS4 NRI1 NRI2 NRI3 NRI4 NRTS1 NRTS2 NRTS3 OSCCLK PWM0 -PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 ROM16 ROM8 ROMCS1 -ROMCS2 ROMCS3 ROMCS4 RXD1 RXD2 RXD3 RXD4 SALT1 SALT2 SALT3 SALT4 SD1 SD2 SGPMCK -SGPMI SGPMLD SGPMO SGPSCK SGPSI0 SGPSI1 SGPSLD SIOONCTRL SIOPBI SIOPBO SIOPWREQ -SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1DEBUG SPI1PASSTHRU SPICS1 TIMER3 TIMER4 -TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 TXD3 TXD4 UART6 USB11D1 USB11H2 USB2D1 -USB2H1 USBCKI VGABIOS_ROM VGAHS VGAVS VPI18 VPI24 VPI30 VPO12 VPO24 WDTRST1 -WDTRST2 - -aspeed,ast2500-pinctrl, aspeed,g5-pinctrl: - -ACPI ADC0 ADC1 ADC10 ADC11 ADC12 ADC13 ADC14 ADC15 ADC2 ADC3 ADC4 ADC5 ADC6 -ADC7 ADC8 ADC9 BMCINT DDCCLK DDCDAT ESPI FWSPICS1 FWSPICS2 GPID0 GPID2 GPID4 -GPID6 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 -I2C7 I2C8 I2C9 LAD0 LAD1 LAD2 LAD3 LCLK LFRAME LPCHC LPCPD LPCPLUS LPCPME -LPCRST LPCSMI LSIRQ MAC1LINK MAC2LINK MDIO1 MDIO2 NCTS1 NCTS2 NCTS3 NCTS4 NDCD1 -NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 NDTR1 NDTR2 NDTR3 NDTR4 NRI1 NRI2 -NRI3 NRI4 NRTS1 NRTS2 NRTS3 NRTS4 OSCCLK PEWAKE PNOR PWM0 PWM1 PWM2 PWM3 PWM4 -PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 RXD1 RXD2 RXD3 RXD4 SALT1 SALT10 -SALT11 SALT12 SALT13 SALT14 SALT2 SALT3 SALT4 SALT5 SALT6 SALT7 SALT8 SALT9 -SCL1 SCL2 SD1 SD2 SDA1 SDA2 SGPM SGPS1 SGPS2 SIOONCTRL SIOPBI SIOPBO SIOPWREQ -SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1CS1 SPI1DEBUG SPI1PASSTHRU SPI2CK SPI2CS0 -SPI2CS1 SPI2MISO SPI2MOSI TIMER3 TIMER4 TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 -TXD3 TXD4 UART6 USB11BHID USB2AD USB2AH USB2BD USB2BH USBCKI VGABIOSROM VGAHS -VGAVS VPI24 VPO WDTRST1 WDTRST2 - -Examples -======== - -g4 Example ----------- - -syscon: scu@1e6e2000 { - compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; - reg = <0x1e6e2000 0x1a8>; - - pinctrl: pinctrl { - compatible = "aspeed,g4-pinctrl"; - - pinctrl_i2c3_default: i2c3_default { - function = "I2C3"; - groups = "I2C3"; - }; - - pinctrl_gpioh0_unbiased_default: gpioh0 { - pins = "A8"; - bias-disable; - }; - }; -}; - -g5 Example ----------- - -ahb { - apb { - syscon: scu@1e6e2000 { - compatible = "aspeed,ast2500-scu", "syscon", "simple-mfd"; - reg = <0x1e6e2000 0x1a8>; - - pinctrl: pinctrl { - compatible = "aspeed,g5-pinctrl"; - aspeed,external-nodes = <&gfx &lhc>; - - pinctrl_i2c3_default: i2c3_default { - function = "I2C3"; - groups = "I2C3"; - }; - - pinctrl_gpioh0_unbiased_default: gpioh0 { - pins = "A18"; - bias-disable; - }; - }; - }; - - gfx: display@1e6e6000 { - compatible = "aspeed,ast2500-gfx", "syscon"; - reg = <0x1e6e6000 0x1000>; - }; - }; - - lpc: lpc@1e789000 { - compatible = "aspeed,ast2500-lpc", "simple-mfd"; - reg = <0x1e789000 0x1000>; - - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x0 0x1e789000 0x1000>; - - lpc_host: lpc-host@80 { - compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon"; - reg = <0x80 0x1e0>; - reg-io-width = <4>; - - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x0 0x80 0x1e0>; - - lhc: lhc@20 { - compatible = "aspeed,ast2500-lhc"; - reg = <0x20 0x24 0x48 0x8>; - }; - }; - }; -}; -- cgit v1.2.3 From 07457937bb5cef8ce797b29d2b0da1bb25509f54 Mon Sep 17 00:00:00 2001 From: Andrew Jeffery Date: Fri, 28 Jun 2019 12:08:32 +0930 Subject: dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema Convert ASPEED pinctrl bindings to DT schema format using json-schema Cc: Johnny Huang Signed-off-by: Andrew Jeffery Link: https://lore.kernel.org/r/20190628023838.15426-3-andrew@aj.id.au Reviewed-by: Rob Herring Signed-off-by: Linus Walleij --- .../bindings/pinctrl/aspeed,ast2400-pinctrl.txt | 80 --------------------- .../bindings/pinctrl/aspeed,ast2400-pinctrl.yaml | 81 ++++++++++++++++++++++ 2 files changed, 81 insertions(+), 80 deletions(-) delete mode 100644 Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.txt deleted file mode 100644 index 67e0325ccf2e..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.txt +++ /dev/null @@ -1,80 +0,0 @@ -============================= -Aspeed AST2400 Pin Controller -============================= - -Required properties for the AST2400: -- compatible : Should be one of the following: - "aspeed,ast2400-pinctrl" - "aspeed,g4-pinctrl" - -The pin controller node should be the child of a syscon node with the required -property: - -- compatible : Should be one of the following: - "aspeed,ast2400-scu", "syscon", "simple-mfd" - "aspeed,g4-scu", "syscon", "simple-mfd" - -Refer to the the bindings described in -Documentation/devicetree/bindings/mfd/syscon.txt - -Subnode Format -============== - -The required properties of pinmux child nodes are: -- function: the mux function to select -- groups : the list of groups to select with this function - -Required properties of pinconf child nodes are: -- groups: A list of groups to select (either this or "pins" must be - specified) -- pins : A list of ball names as strings, eg "D14" (either this or "groups" - must be specified) - -Optional properties of pinconf child nodes are: -- bias-disable : disable any pin bias -- bias-pull-down: pull down the pin -- drive-strength: sink or source at most X mA - -Definitions are as specified in -Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt, with any -further limitations as described above. - -For pinmux, each mux function has only one associated pin group. Each group is -named by its function. The following values for the function and groups -properties are supported: - -ACPI ADC0 ADC1 ADC10 ADC11 ADC12 ADC13 ADC14 ADC15 ADC2 ADC3 ADC4 ADC5 ADC6 -ADC7 ADC8 ADC9 BMCINT DDCCLK DDCDAT EXTRST FLACK FLBUSY FLWP GPID GPID0 GPID2 -GPID4 GPID6 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 -I2C5 I2C6 I2C7 I2C8 I2C9 LPCPD LPCPME LPCRST LPCSMI MAC1LINK MAC2LINK MDIO1 -MDIO2 NCTS1 NCTS2 NCTS3 NCTS4 NDCD1 NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 -NDTR1 NDTR2 NDTR3 NDTR4 NDTS4 NRI1 NRI2 NRI3 NRI4 NRTS1 NRTS2 NRTS3 OSCCLK PWM0 -PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 ROM16 ROM8 ROMCS1 -ROMCS2 ROMCS3 ROMCS4 RXD1 RXD2 RXD3 RXD4 SALT1 SALT2 SALT3 SALT4 SD1 SD2 SGPMCK -SGPMI SGPMLD SGPMO SGPSCK SGPSI0 SGPSI1 SGPSLD SIOONCTRL SIOPBI SIOPBO SIOPWREQ -SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1DEBUG SPI1PASSTHRU SPICS1 TIMER3 TIMER4 -TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 TXD3 TXD4 UART6 USB11D1 USB11H2 USB2D1 -USB2H1 USBCKI VGABIOS_ROM VGAHS VGAVS VPI18 VPI24 VPI30 VPO12 VPO24 WDTRST1 -WDTRST2 - -Example -======= - -syscon: scu@1e6e2000 { - compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; - reg = <0x1e6e2000 0x1a8>; - - pinctrl: pinctrl { - compatible = "aspeed,g4-pinctrl"; - - pinctrl_i2c3_default: i2c3_default { - function = "I2C3"; - groups = "I2C3"; - }; - - pinctrl_gpioh0_unbiased_default: gpioh0 { - pins = "A8"; - bias-disable; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml new file mode 100644 index 000000000000..61a110a7db8a --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml @@ -0,0 +1,81 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/aspeed,ast2400-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ASPEED AST2400 Pin Controller + +maintainers: + - Andrew Jeffery + +description: |+ + The pin controller node should be the child of a syscon node with the + required property: + + - compatible: Should be one of the following: + "aspeed,ast2400-scu", "syscon", "simple-mfd" + "aspeed,g4-scu", "syscon", "simple-mfd" + + Refer to the the bindings described in + Documentation/devicetree/bindings/mfd/syscon.txt + +properties: + compatible: + enum: [ aspeed,ast2400-pinctrl, aspeed,g4-pinctrl ] + +patternProperties: + '^.*$': + if: + type: object + then: + patternProperties: + "^function|groups$": + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: [ "ACPI", "ADC0", "ADC1", "ADC10", "ADC11", "ADC12", "ADC13", + "ADC14", "ADC15", "ADC2", "ADC3", "ADC4", "ADC5", "ADC6", "ADC7", + "ADC8", "ADC9", "BMCINT", "DDCCLK", "DDCDAT", "EXTRST", "FLACK", + "FLBUSY", "FLWP", "GPID", "GPID0", "GPID2", "GPID4", "GPID6", + "GPIE0", "GPIE2", "GPIE4", "GPIE6", "I2C10", "I2C11", "I2C12", + "I2C13", "I2C14", "I2C3", "I2C4", "I2C5", "I2C6", "I2C7", "I2C8", + "I2C9", "LPCPD", "LPCPME", "LPCRST", "LPCSMI", "MAC1LINK", + "MAC2LINK", "MDIO1", "MDIO2", "NCTS1", "NCTS2", "NCTS3", "NCTS4", + "NDCD1", "NDCD2", "NDCD3", "NDCD4", "NDSR1", "NDSR2", "NDSR3", + "NDSR4", "NDTR1", "NDTR2", "NDTR3", "NDTR4", "NDTS4", "NRI1", + "NRI2", "NRI3", "NRI4", "NRTS1", "NRTS2", "NRTS3", "OSCCLK", + "PWM0", "PWM1", "PWM2", "PWM3", "PWM4", "PWM5", "PWM6", "PWM7", + "RGMII1", "RGMII2", "RMII1", "RMII2", "ROM16", "ROM8", "ROMCS1", + "ROMCS2", "ROMCS3", "ROMCS4", "RXD1", "RXD2", "RXD3", "RXD4", + "SALT1", "SALT2", "SALT3", "SALT4", "SD1", "SD2", "SGPMCK", + "SGPMI", "SGPMLD", "SGPMO", "SGPSCK", "SGPSI0", "SGPSI1", "SGPSLD", + "SIOONCTRL", "SIOPBI", "SIOPBO", "SIOPWREQ", "SIOPWRGD", "SIOS3", + "SIOS5", "SIOSCI", "SPI1", "SPI1DEBUG", "SPI1PASSTHRU", "SPICS1", + "TIMER3", "TIMER4", "TIMER5", "TIMER6", "TIMER7", "TIMER8", "TXD1", + "TXD2", "TXD3", "TXD4", "UART6", "USB11D1", "USB11H2", "USB2D1", + "USB2H1", "USBCKI", "VGABIOS_ROM", "VGAHS", "VGAVS", "VPI18", + "VPI24", "VPI30", "VPO12", "VPO24", "WDTRST1", "WDTRST2" ] + +required: + - compatible + +examples: + - | + syscon: scu@1e6e2000 { + compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; + + pinctrl: pinctrl { + compatible = "aspeed,g4-pinctrl"; + + pinctrl_i2c3_default: i2c3_default { + function = "I2C3"; + groups = "I2C3"; + }; + + pinctrl_gpioh0_unbiased_default: gpioh0 { + pins = "A8"; + bias-disable; + }; + }; + }; -- cgit v1.2.3 From 0a617de167306231bdbf894aa2b93f4b2cd2a781 Mon Sep 17 00:00:00 2001 From: Andrew Jeffery Date: Fri, 28 Jun 2019 12:08:33 +0930 Subject: dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema Convert ASPEED pinctrl bindings to DT schema format using json-schema. Cc: Johnny Huang Signed-off-by: Andrew Jeffery Link: https://lore.kernel.org/r/20190628023838.15426-4-andrew@aj.id.au Signed-off-by: Linus Walleij --- .../bindings/pinctrl/aspeed,ast2500-pinctrl.txt | 119 ------------------ .../bindings/pinctrl/aspeed,ast2500-pinctrl.yaml | 134 +++++++++++++++++++++ 2 files changed, 134 insertions(+), 119 deletions(-) delete mode 100644 Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.txt deleted file mode 100644 index ca7025dc1901..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.txt +++ /dev/null @@ -1,119 +0,0 @@ -============================= -Aspeed AST2500 Pin Controller -============================= - -Required properties for g5: -- compatible : Should be one of the following: - "aspeed,ast2500-pinctrl" - "aspeed,g5-pinctrl" - -- aspeed,external-nodes: A cell of phandles to external controller nodes: - 0: compatible with "aspeed,ast2500-gfx", "syscon" - 1: compatible with "aspeed,ast2500-lhc", "syscon" - -The pin controller node should be the child of a syscon node with the required -property: - -- compatible : Should be one of the following: - "aspeed,ast2500-scu", "syscon", "simple-mfd" - "aspeed,g5-scu", "syscon", "simple-mfd" - -Refer to the the bindings described in -Documentation/devicetree/bindings/mfd/syscon.txt - -Subnode Format -============== - -The required properties of pinmux child nodes are: -- function: the mux function to select -- groups : the list of groups to select with this function - -Required properties of pinconf child nodes are: -- groups: A list of groups to select (either this or "pins" must be - specified) -- pins : A list of ball names as strings, eg "D14" (either this or "groups" - must be specified) - -Optional properties of pinconf child nodes are: -- bias-disable : disable any pin bias -- bias-pull-down: pull down the pin -- drive-strength: sink or source at most X mA - -Definitions are as specified in -Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt, with any -further limitations as described above. - -For pinmux, each mux function has only one associated pin group. Each group is -named by its function. The following values for the function and groups -properties are supported: - -ACPI ADC0 ADC1 ADC10 ADC11 ADC12 ADC13 ADC14 ADC15 ADC2 ADC3 ADC4 ADC5 ADC6 -ADC7 ADC8 ADC9 BMCINT DDCCLK DDCDAT ESPI FWSPICS1 FWSPICS2 GPID0 GPID2 GPID4 -GPID6 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 -I2C7 I2C8 I2C9 LAD0 LAD1 LAD2 LAD3 LCLK LFRAME LPCHC LPCPD LPCPLUS LPCPME -LPCRST LPCSMI LSIRQ MAC1LINK MAC2LINK MDIO1 MDIO2 NCTS1 NCTS2 NCTS3 NCTS4 NDCD1 -NDCD2 NDCD3 NDCD4 NDSR1 NDSR2 NDSR3 NDSR4 NDTR1 NDTR2 NDTR3 NDTR4 NRI1 NRI2 -NRI3 NRI4 NRTS1 NRTS2 NRTS3 NRTS4 OSCCLK PEWAKE PNOR PWM0 PWM1 PWM2 PWM3 PWM4 -PWM5 PWM6 PWM7 RGMII1 RGMII2 RMII1 RMII2 RXD1 RXD2 RXD3 RXD4 SALT1 SALT10 -SALT11 SALT12 SALT13 SALT14 SALT2 SALT3 SALT4 SALT5 SALT6 SALT7 SALT8 SALT9 -SCL1 SCL2 SD1 SD2 SDA1 SDA2 SGPM SGPS1 SGPS2 SIOONCTRL SIOPBI SIOPBO SIOPWREQ -SIOPWRGD SIOS3 SIOS5 SIOSCI SPI1 SPI1CS1 SPI1DEBUG SPI1PASSTHRU SPI2CK SPI2CS0 -SPI2CS1 SPI2MISO SPI2MOSI TIMER3 TIMER4 TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD2 -TXD3 TXD4 UART6 USB11BHID USB2AD USB2AH USB2BD USB2BH USBCKI VGABIOSROM VGAHS -VGAVS VPI24 VPO WDTRST1 WDTRST2 - -Example -======= - -ahb { - apb { - syscon: scu@1e6e2000 { - compatible = "aspeed,ast2500-scu", "syscon", "simple-mfd"; - reg = <0x1e6e2000 0x1a8>; - - pinctrl: pinctrl { - compatible = "aspeed,g5-pinctrl"; - aspeed,external-nodes = <&gfx &lhc>; - - pinctrl_i2c3_default: i2c3_default { - function = "I2C3"; - groups = "I2C3"; - }; - - pinctrl_gpioh0_unbiased_default: gpioh0 { - pins = "A18"; - bias-disable; - }; - }; - }; - - gfx: display@1e6e6000 { - compatible = "aspeed,ast2500-gfx", "syscon"; - reg = <0x1e6e6000 0x1000>; - }; - }; - - lpc: lpc@1e789000 { - compatible = "aspeed,ast2500-lpc", "simple-mfd"; - reg = <0x1e789000 0x1000>; - - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x0 0x1e789000 0x1000>; - - lpc_host: lpc-host@80 { - compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon"; - reg = <0x80 0x1e0>; - reg-io-width = <4>; - - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x0 0x80 0x1e0>; - - lhc: lhc@20 { - compatible = "aspeed,ast2500-lhc"; - reg = <0x20 0x24 0x48 0x8>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml new file mode 100644 index 000000000000..cf561bd55128 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/aspeed,ast2500-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ASPEED AST2500 Pin Controller + +maintainers: + - Andrew Jeffery + +description: |+ + The pin controller node should be the child of a syscon node with the + required property: + + - compatible: Should be one of the following: + "aspeed,ast2500-scu", "syscon", "simple-mfd" + "aspeed,g5-scu", "syscon", "simple-mfd" + + Refer to the the bindings described in + Documentation/devicetree/bindings/mfd/syscon.txt + +properties: + compatible: + enum: [ aspeed,ast2500-pinctrl, aspeed,g5-pinctrl ] + aspeed,external-nodes: + minItems: 2 + maxItems: 2 + allOf: + - $ref: /schemas/types.yaml#/definitions/phandle-array + description: | + A cell of phandles to external controller nodes: + 0: compatible with "aspeed,ast2500-gfx", "syscon" + 1: compatible with "aspeed,ast2500-lhc", "syscon" + +patternProperties: + '^.*$': + if: + type: object + then: + patternProperties: + "^function|groups$": + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: [ "ACPI", "ADC0", "ADC1", "ADC10", "ADC11", "ADC12", "ADC13", + "ADC14", "ADC15", "ADC2", "ADC3", "ADC4", "ADC5", "ADC6", "ADC7", + "ADC8", "ADC9", "BMCINT", "DDCCLK", "DDCDAT", "ESPI", "FWSPICS1", + "FWSPICS2", "GPID0", "GPID2", "GPID4", "GPID6", "GPIE0", "GPIE2", + "GPIE4", "GPIE6", "I2C10", "I2C11", "I2C12", "I2C13", "I2C14", + "I2C3", "I2C4", "I2C5", "I2C6", "I2C7", "I2C8", "I2C9", "LAD0", + "LAD1", "LAD2", "LAD3", "LCLK", "LFRAME", "LPCHC", "LPCPD", + "LPCPLUS", "LPCPME", "LPCRST", "LPCSMI", "LSIRQ", "MAC1LINK", + "MAC2LINK", "MDIO1", "MDIO2", "NCTS1", "NCTS2", "NCTS3", "NCTS4", + "NDCD1", "NDCD2", "NDCD3", "NDCD4", "NDSR1", "NDSR2", "NDSR3", + "NDSR4", "NDTR1", "NDTR2", "NDTR3", "NDTR4", "NRI1", "NRI2", + "NRI3", "NRI4", "NRTS1", "NRTS2", "NRTS3", "NRTS4", "OSCCLK", + "PEWAKE", "PNOR", "PWM0", "PWM1", "PWM2", "PWM3", "PWM4", "PWM5", + "PWM6", "PWM7", "RGMII1", "RGMII2", "RMII1", "RMII2", "RXD1", + "RXD2", "RXD3", "RXD4", "SALT1", "SALT10", "SALT11", "SALT12", + "SALT13", "SALT14", "SALT2", "SALT3", "SALT4", "SALT5", "SALT6", + "SALT7", "SALT8", "SALT9", "SCL1", "SCL2", "SD1", "SD2", "SDA1", + "SDA2", "SGPS1", "SGPS2", "SIOONCTRL", "SIOPBI", "SIOPBO", + "SIOPWREQ", "SIOPWRGD", "SIOS3", "SIOS5", "SIOSCI", "SPI1", + "SPI1CS1", "SPI1DEBUG", "SPI1PASSTHRU", "SPI2CK", "SPI2CS0", + "SPI2CS1", "SPI2MISO", "SPI2MOSI", "TIMER3", "TIMER4", "TIMER5", + "TIMER6", "TIMER7", "TIMER8", "TXD1", "TXD2", "TXD3", "TXD4", + "UART6", "USB11BHID", "USB2AD", "USB2AH", "USB2BD", "USB2BH", + "USBCKI", "VGABIOSROM", "VGAHS", "VGAVS", "VPI24", "VPO", + "WDTRST1", "WDTRST2", ] + +required: + - compatible + - aspeed,external-nodes + +examples: + - | + compatible = "simple-bus"; + ranges; + + apb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + syscon: scu@1e6e2000 { + compatible = "aspeed,ast2500-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; + + pinctrl: pinctrl { + compatible = "aspeed,g5-pinctrl"; + aspeed,external-nodes = <&gfx &lhc>; + + pinctrl_i2c3_default: i2c3_default { + function = "I2C3"; + groups = "I2C3"; + }; + + pinctrl_gpioh0_unbiased_default: gpioh0 { + pins = "A18"; + bias-disable; + }; + }; + }; + + gfx: display@1e6e6000 { + compatible = "aspeed,ast2500-gfx", "syscon"; + reg = <0x1e6e6000 0x1000>; + }; + }; + + lpc: lpc@1e789000 { + compatible = "aspeed,ast2500-lpc", "simple-mfd"; + reg = <0x1e789000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x1e789000 0x1000>; + + lpc_host: lpc-host@80 { + compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon"; + reg = <0x80 0x1e0>; + reg-io-width = <4>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x80 0x1e0>; + + lhc: lhc@20 { + compatible = "aspeed,ast2500-lhc"; + reg = <0x20 0x24 0x48 0x8>; + }; + }; + }; -- cgit v1.2.3 From 80327437e377bd4d3f696ccec94b78895e6359f9 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Tue, 2 Jul 2019 16:20:43 +0530 Subject: dt-bindings: pinctrl: qcom: Document missing gpio nodes The bindings for msm8998-pinctrl was missing gpio-ranges and gpio-reserved-ranges, so document them as well Signed-off-by: Vinod Koul Link: https://lore.kernel.org/r/20190702105045.27646-2-vkoul@kernel.org Reviewed-by: Bjorn Andersson Signed-off-by: Linus Walleij --- .../devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt index 00174f08ba1d..cdec1eeb2799 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt @@ -40,6 +40,14 @@ MSM8998 platform. Definition: must be 2. Specifying the pin number and flags, as defined in +- gpio-ranges: + Usage: required + Definition: see ../gpio/gpio.txt + +- gpio-reserved-ranges: + Usage: optional + Definition: see ../gpio/gpio.txt + Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for a general description of GPIO and interrupt bindings. @@ -175,6 +183,8 @@ Example: interrupts = <0 208 0>; gpio-controller; #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 175>; + gpio-reserved-ranges = <0 4>, <81 4>; interrupt-controller; #interrupt-cells = <2>; -- cgit v1.2.3 From 7f1fee22a2bb4073ddd2f4b06b6710a561ef3815 Mon Sep 17 00:00:00 2001 From: Prasad Sodagudi Date: Tue, 2 Jul 2019 16:20:44 +0530 Subject: dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding Add the binding for the TLMM pinctrl block found in the SM8150 platform. Signed-off-by: Prasad Sodagudi Signed-off-by: Isaac J. Manjarres [vkoul: add missing nodes of gpio range and reserved rewrote function names and order them] Signed-off-by: Vinod Koul Link: https://lore.kernel.org/r/20190702105045.27646-3-vkoul@kernel.org Reviewed-by: Bjorn Andersson Signed-off-by: Linus Walleij --- .../bindings/pinctrl/qcom,sm8150-pinctrl.txt | 190 +++++++++++++++++++++ 1 file changed, 190 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sm8150-pinctrl.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8150-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sm8150-pinctrl.txt new file mode 100644 index 000000000000..fa37733e5102 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8150-pinctrl.txt @@ -0,0 +1,190 @@ +Qualcomm SM8150 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +QCS404 platform. + +- compatible: + Usage: required + Value type: + Definition: must be "qcom,sm8150-pinctrl" + +- reg: + Usage: required + Value type: + Definition: the base address and size of the north, south, west + and east TLMM tiles. + +- reg-names: + Usage: required + Value type: + Defintiion: names for the cells of reg, must contain "north", "south" + "west" and "east". + +- interrupts: + Usage: required + Value type: + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: + Definition: must be 2. Specifying the pin number and flags, as defined + in + +- gpio-controller: + Usage: required + Value type: + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: + Definition: must be 2. Specifying the pin number and flags, as defined + in + +- gpio-ranges: + Usage: required + Value type: + Definition: see ../gpio/gpio.txt + +- gpio-reserved-ranges: + Usage: optional + Value type: + Definition: see ../gpio/gpio.txt + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: + Definition: List of gpio pins affected by the properties specified in + this subnode. + + Valid pins are: + gpio0-gpio149 + Supports mux, bias and drive-strength + + sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd, + sdc2_data sdc1_rclk + Supports bias and drive-strength + + ufs_reset + Supports bias and drive-strength + +- function: + Usage: required + Value type: + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + + adsp_ext, agera_pll, aoss_cti, ddr_pxi2, atest_char, + atest_char0, atest_char1, atest_char2, atest_char3, + audio_ref, atest_usb1, atest_usb2, atest_usb10, + atest_usb11, atest_usb12, atest_usb13, atest_usb20, + atest_usb21, atest_usb22, atest_usb2, atest_usb23, + btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0, + cci_timer1, cci_timer2, cci_timer3, cci_timer4, + cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist, + ddr_pxi0, ddr_pxi1, ddr_pxi3, edp_hot, edp_lcd, + emac_phy, emac_pps, gcc_gp1, gcc_gp2, gcc_gp3, gpio, + hs1_mi2s, hs2_mi2s, hs3_mi2s, jitter_bist, + lpass_slimbus, mdp_vsync, mdp_vsync0, mdp_vsync1, + mdp_vsync2, mdp_vsync3, mss_lte, m_voc, nav_pps, + pa_indicator, pci_e0, phase_flag, pll_bypassnl, + pll_bist, pci_e1, pll_reset, pri_mi2s, pri_mi2s_ws, + prng_rosc, qdss, qdss_cti, qlink_request, qlink_enable, + qspi0, qspi1, qspi2, qspi3, qspi_clk, qspi_cs, qua_mi2s, + qup0, qup1, qup2, qup3, qup4, qup5, qup6, qup7, qup8, + qup9, qup10, qup11, qup12, qup13, qup14, qup15, qup16, + qup17, qup18, qup19, qup_l4, qup_l5, qup_l6, rgmii, + sdc4, sd_write, sec_mi2s, spkr_i2s, sp_cmu, ter_mi2s, + tgu_ch0, tgu_ch1, tgu_ch2, tgu_ch3, tsense_pwm1, + tsense_pwm2, tsif1, tsif2, uim1, uim2, uim_batt, + usb2phy_ac, usb_phy, vfr_1, vsense_trigger, wlan1_adc0, + wlan1_adc1, wlan2_adc0, wlan2_adc1, wmss_reset + +- bias-disable: + Usage: optional + Value type: + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@3000000 { + compatible = "qcom,sm8150-pinctrl"; + reg = <0x03100000 0x300000>, + <0x03500000 0x300000>, + <0x03900000 0x300000>, + <0x03D00000 0x300000>; + reg-names = "west", "east", "north", "south"; + interrupts = ; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 175>; + gpio-reserved-ranges = <0 4>, <126 4>; + interrupt-controller; + #interrupt-cells = <2>; + }; -- cgit v1.2.3