From 6acd6ad562067e6c621c346e0134131bdb3b1080 Mon Sep 17 00:00:00 2001 From: Jonathan McDowell Date: Mon, 18 May 2020 19:09:49 +0100 Subject: ARM: dts: qcom: add ethernet definitions to ipq8064 Plumb in the 4 IPQ8064 stmmac based ethernet interfaces. Signed-off-by: Jonathan McDowell Link: https://lore.kernel.org/r/723344332357b5eed957443ec4a705a080fcc2da.1589824955.git.noodles@earth.li Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-ipq8064.dtsi | 108 ++++++++++++++++++++++++++++++++++++ 1 file changed, 108 insertions(+) diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi index b912da9a3ff3..9c0d5510c805 100644 --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi @@ -597,6 +597,114 @@ perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>; }; + nss_common: syscon@03000000 { + compatible = "syscon"; + reg = <0x03000000 0x0000FFFF>; + }; + + qsgmii_csr: syscon@1bb00000 { + compatible = "syscon"; + reg = <0x1bb00000 0x000001FF>; + }; + + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <7>; + snps,rd_osr_lmt = <7>; + snps,blen = <16 0 0 0 0 0 0>; + }; + + gmac0: ethernet@37000000 { + device_type = "network"; + compatible = "qcom,ipq806x-gmac"; + reg = <0x37000000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; + + snps,axi-config = <&stmmac_axi_setup>; + snps,pbl = <32>; + snps,aal = <1>; + + qcom,nss-common = <&nss_common>; + qcom,qsgmii-csr = <&qsgmii_csr>; + + clocks = <&gcc GMAC_CORE1_CLK>; + clock-names = "stmmaceth"; + + resets = <&gcc GMAC_CORE1_RESET>; + reset-names = "stmmaceth"; + + status = "disabled"; + }; + + gmac1: ethernet@37200000 { + device_type = "network"; + compatible = "qcom,ipq806x-gmac"; + reg = <0x37200000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; + + snps,axi-config = <&stmmac_axi_setup>; + snps,pbl = <32>; + snps,aal = <1>; + + qcom,nss-common = <&nss_common>; + qcom,qsgmii-csr = <&qsgmii_csr>; + + clocks = <&gcc GMAC_CORE2_CLK>; + clock-names = "stmmaceth"; + + resets = <&gcc GMAC_CORE2_RESET>; + reset-names = "stmmaceth"; + + status = "disabled"; + }; + + gmac2: ethernet@37400000 { + device_type = "network"; + compatible = "qcom,ipq806x-gmac"; + reg = <0x37400000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; + + snps,axi-config = <&stmmac_axi_setup>; + snps,pbl = <32>; + snps,aal = <1>; + + qcom,nss-common = <&nss_common>; + qcom,qsgmii-csr = <&qsgmii_csr>; + + clocks = <&gcc GMAC_CORE3_CLK>; + clock-names = "stmmaceth"; + + resets = <&gcc GMAC_CORE3_RESET>; + reset-names = "stmmaceth"; + + status = "disabled"; + }; + + gmac3: ethernet@37600000 { + device_type = "network"; + compatible = "qcom,ipq806x-gmac"; + reg = <0x37600000 0x200000>; + interrupts = ; + interrupt-names = "macirq"; + + snps,axi-config = <&stmmac_axi_setup>; + snps,pbl = <32>; + snps,aal = <1>; + + qcom,nss-common = <&nss_common>; + qcom,qsgmii-csr = <&qsgmii_csr>; + + clocks = <&gcc GMAC_CORE4_CLK>; + clock-names = "stmmaceth"; + + resets = <&gcc GMAC_CORE4_RESET>; + reset-names = "stmmaceth"; + + status = "disabled"; + }; + vsdcc_fixed: vsdcc-regulator { compatible = "regulator-fixed"; regulator-name = "SDCC Power"; -- cgit v1.2.3 From 5de14398b6611af89a253f3fa13c20a92d53a513 Mon Sep 17 00:00:00 2001 From: Jonathan McDowell Date: Mon, 18 May 2020 19:10:14 +0100 Subject: ARM: dts: qcom: Add MikroTik RB3011 This patch adds a DTS file for the MikroTik RouterBoard 3011, which is a 1U rackmount router based on the IPQ8064, supporting the serial UART, dual QCA8337 Gigabit ethernet switches, boot loader NOR and user LED device. Signed-off-by: Jonathan McDowell Link: https://lore.kernel.org/r/75390e66c9e6e36ddd42dc7f54cac28dfd7a24b9.1589824955.git.noodles@earth.li Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 308 ++++++++++++++++++++++++++++++ 2 files changed, 309 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index e8dd99201397..e697a4bd7426 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -884,6 +884,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ qcom-ipq8064-ap148.dtb \ + qcom-ipq8064-rb3011.dtb \ qcom-msm8660-surf.dtb \ qcom-msm8960-cdp.dtb \ qcom-msm8974-fairphone-fp2.dtb \ diff --git a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts new file mode 100644 index 000000000000..282b89ce3d45 --- /dev/null +++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts @@ -0,0 +1,308 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "qcom-ipq8064.dtsi" +#include + +/ { + model = "MikroTik RB3011UiAS-RM"; + compatible = "mikrotik,rb3011"; + + aliases { + serial0 = &gsbi7_serial; + ethernet0 = &gmac0; + ethernet1 = &gmac3; + mdio-gpio0 = &mdio0; + mdio-gpio1 = &mdio1; + }; + + chosen { + bootargs = "loglevel=8 console=ttyMSM0,115200"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + reg = <0x42000000 0x3e000000>; + device_type = "memory"; + }; + + mdio0: mdio@0 { + status = "okay"; + compatible = "virtual,mdio-gpio"; + gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>, + <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + switch0: switch@10 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + + dsa,member = <0 0>; + + pinctrl-0 = <&sw0_reset_pin>; + pinctrl-names = "default"; + + reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + switch0cpu: port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii-id"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "sw1"; + }; + + port@2 { + reg = <2>; + label = "sw2"; + }; + + port@3 { + reg = <3>; + label = "sw3"; + }; + + port@4 { + reg = <4>; + label = "sw4"; + }; + + port@5 { + reg = <5>; + label = "sw5"; + }; + }; + }; + }; + + mdio1: mdio@1 { + status = "okay"; + compatible = "virtual,mdio-gpio"; + gpios = <&qcom_pinmux 11 GPIO_ACTIVE_HIGH>, + <&qcom_pinmux 10 GPIO_ACTIVE_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-0 = <&mdio1_pins>; + pinctrl-names = "default"; + + switch1: switch@14 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + + dsa,member = <1 0>; + + pinctrl-0 = <&sw1_reset_pin>; + pinctrl-names = "default"; + + reset-gpios = <&qcom_pinmux 17 GPIO_ACTIVE_LOW>; + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + switch1cpu: port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac3>; + phy-mode = "sgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "sw6"; + }; + + port@2 { + reg = <2>; + label = "sw7"; + }; + + port@3 { + reg = <3>; + label = "sw8"; + }; + + port@4 { + reg = <4>; + label = "sw9"; + }; + + port@5 { + reg = <5>; + label = "sw10"; + }; + }; + }; + }; + + soc { + gsbi5: gsbi@1a200000 { + qcom,mode = ; + status = "okay"; + + spi4: spi@1a280000 { + status = "okay"; + spi-max-frequency = <50000000>; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + norflash: s25fl016k@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + + partition@0 { + label = "RouterBoot"; + reg = <0x0 0x40000>; + }; + }; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-0 = <&buttons_pins>; + pinctrl-names = "default"; + + button@1 { + label = "reset"; + linux,code = ; + gpios = <&qcom_pinmux 66 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&leds_pins>; + pinctrl-names = "default"; + + led@7 { + label = "rb3011:green:user"; + gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + }; +}; + +&gmac0 { + status = "okay"; + + phy-mode = "rgmii"; + qcom,id = <0>; + phy-handle = <&switch0cpu>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac3 { + status = "okay"; + + phy-mode = "sgmii"; + qcom,id = <3>; + phy-handle = <&switch1cpu>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gsbi7 { + status = "okay"; + qcom,mode = ; +}; + +&gsbi7_serial { + status = "okay"; +}; + +&qcom_pinmux { + buttons_pins: buttons_pins { + mux { + pins = "gpio66"; + drive-strength = <16>; + bias-disable; + }; + }; + + leds_pins: leds_pins { + mux { + pins = "gpio33"; + drive-strength = <16>; + bias-disable; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; + + mdio1_pins: mdio1_pins { + mux { + pins = "gpio10", "gpio11"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; + + sw0_reset_pin: sw0_reset_pin { + mux { + pins = "gpio16"; + drive-strength = <16>; + function = "gpio"; + bias-disable; + input-disable; + }; + }; + + sw1_reset_pin: sw1_reset_pin { + mux { + pins = "gpio17"; + drive-strength = <16>; + function = "gpio"; + bias-disable; + input-disable; + }; + }; +}; -- cgit v1.2.3 From 5de47779cf7cf9584f3a2f45124014480eab950b Mon Sep 17 00:00:00 2001 From: Jonathan McDowell Date: Tue, 16 Jun 2020 18:15:54 +0100 Subject: ARM: dts: qcom: add qfprom definition to ipq806x Add missing qfprom definition for ipq806x SoC Signed-off-by: Jonathan McDowell Link: https://lore.kernel.org/r/20200616171554.GA5632@earth.li Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-ipq8064.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi index 9c0d5510c805..c51481405e7f 100644 --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi @@ -425,6 +425,13 @@ qcom,controller-type = "pmic-arbiter"; }; + qfprom: qfprom@700000 { + compatible = "qcom,qfprom"; + reg = <0x00700000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + }; + gcc: clock-controller@900000 { compatible = "qcom,gcc-ipq8064"; reg = <0x00900000 0x4000>; -- cgit v1.2.3