| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
'asoc/fix/tlv320aic3x' and 'asoc/fix/topology' into asoc-linus
|
|
'asoc/fix/dwc', 'asoc/fix/fsl-ssi' and 'asoc/fix/hdmi-codec' into asoc-linus
|
|
|
|
|
|
|
|
The i2s clock pre-divider 1 is used for both i2s1 and sysclk.
The i2s1 is usually used for the main i2s and the pre-divider
will be set in hw_params function.
However, if i2s2 is used, the pre-divider is not set in the hw_params
function and the default value of i2s clock pre-divider 1 is too high
for sysclk and DMIC usage. Fix by overriding default divider value to 2.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=95681
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When multiple front-ends are using the same back-end, putting state of a
front-end to STOP state upon receiving pause command will result in backend
stream getting released by DPCM framework unintentionally. In order to
avoid backend to be released when another active front-end stream is
present, put the stream state to PAUSED state instead of STOP state.
Signed-off-by: Patrick Lai <plai@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Saved firmware ctx was not never released, so release Firmware
ctx in cleanup routine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Frequency value of zero did not make sense, use same 24.576MHz
setting and only change the clock source in idle mode
Suggested-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The fsl_ssi fifo watermark is by default set to 2 free spaces (i.e.
activate DMA on FIFO when only 2 spaces are left.) This means the
DMA must service the fifo within 2 audio samples, which is just not
enough time for many use cases with high data rate. In many
configurations the audio channel slips (causing l/r swap in stereo
configurations, or channel slipping in multi-channel configurations).
This patch gives more breathing room and allows the SSI to operate
reliably by changing the fifio refill watermark to 8.
There is no change in behavior for older chips (with an 8-deep fifo).
Only the newer chips with a 15-deep fifo get the new behavior. I
suspect a new fifo depth setting could be optimized on the older
chips too, but I have not tested.
Signed-off-by: Caleb Crome <caleb@crome.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The clk_ref_div is not configured in the correct position of the
register. The patch fixes that clk_ref_div, Pre-Scalar, is assigned
the wrong value.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Change to correct name of the register function.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If a module is not available in a pipeline, fail safely rather than
causing oops.
Signed-off-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The RESET register only have one self clearing bit and it should not be
cached. If it is cached, when we sync the registers back to the chip we
will initiate a software reset as well, which is not desirable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently binding of auxiliary devices doesn't work as in
soc_bind_aux_dev() function a bound component is not being added
to any list and in soc_probe_aux_devices() we are trying to walk
the component_dev_list list to probe auxiliary components but
at that time this list doesn't contain any auxiliary components
since they are being added to the card only in soc_probe_component().
This patch adds a list to the card where are stored bound but not
probed auxiliary devices, so that all aux devices can be probed.
Fixes: 1a653aa44725 "ASoC: core: replace aux_comp_list to component_dev_list"
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Protect against corrupt firmware files by ensuring that the length we
get for the data in a region actually lies within the available firmware
file data buffer.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit df1a2776a795 ("ASoC: Intel: bytcr_rt5640: add MCLK support")
was merged but the corresponding clock framework patches have not,
after being bumped from audio to clock to x86 domains. The missing
clock-related patches result in a regression starting with 4.9 with
the audio card not being created.
Rather than reverting this commit and all following updates already
queued up for 4.10, handle run-time dependency on MCLK and fall back
to the previous bit-clock mode. This provides the same functionality
as in 4.8 for Baytrail devices. On Baytrail-CR most devices remain
silent with this fallback but additional patches are needed anyway.
As suggested by Mark Brown, the fallback is only allowed with -ENOENT,
all other run-time errors, including -EPROBE_DEFER, will stop the probe
with no sound card registered.
This patch should be applied to -stable as well as ASoC 4.10 fixes
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
kcontrol->private_value is being kfree'd after kcontrol has been freed
(in previous call to snd_ctl_remove). Instead, fix this by kfreeing
the private_value before kcontrol.
CoverityScan CID#1388311 "Read from pointer after free"
Fixes: eea3dd4f1247a ("ASoC: topology: Only free TLV for volume mixers of a widget")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On an error, snd_ctl_add already free's kctrl, so calling snd_ctl_free_one
to free it again leads to a double free error. Fix this by removing
the extraneous snd_ctl_free_one call.
Issue found using static analysis with CoverityScan, CID 1372908
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"No dramatic changes are found in this development cycle, but as usual,
many commits are applied in a wide range of drivers.
Most of big changes are in ASoC, where a few bits of framework work
and quite a lot of cleanups and improvements to existing code have
been done. The rest are usual stuff, a few HD-audio and USB-audio
quirks and fixes, as well as the drop of kthread usages in the whole
subsystem.
Below are some highlights:
ASoC:
- support for stereo DAPM controls
- some initial work on the of-graph sound card
- regmap conversions of the remaining AC'97 drivers
- a new version of the topology ABI; this should be backward
compatible
- updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
Intel skylake, atom-sst
- new drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
Realtek RT5665
USB-audio:
- yet another race fix at disconnection
- tolerated packet size calculation for some Android devices
- quirks for Axe-Fx II, QuickCam, TEAC 501/503
HD-audio:
- improvement of Dell pin fixup mapping
- quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic
Misc:
- replace all kthread usages with simple works"
* tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (296 commits)
ALSA: hiface: Fix M2Tech hiFace driver sampling rate change
ALSA: usb-audio: Eliminate noise at the start of DSD playback.
ALSA: usb-audio: Add native DSD support for TEAC 501/503 DAC
ASoC: wm_adsp: wm_adsp_buf_alloc should use kfree in error path
ASoC: topology: avoid uninitialized kcontrol_type
ALSA: usb-audio: Add QuickCam Communicate Deluxe/S7500 to volume_control_quirks
ALSA: usb-audio: add implicit fb quirk for Axe-Fx II
ASoC: zte: spdif: correct ZX_SPDIF_CLK_RAT define
ASoC: zte: spdif and i2s drivers are not zx296702 specific
ASoC: rsnd: setup BRGCKR/BRRA/BRRB when starting
ASoC: rsnd: enable/disable ADG when suspend/resume timing
ASoC: rsnd: tidyup ssi->usrcnt counter check in hw_params
ALSA: cs46xx: add a new line
ASoC: Intel: update bxt_da7219_max98357a to support quad ch dmic capture
ASoC: nau8825: disable sinc filter for high THD of ADC
ALSA: usb-audio: more tolerant packetsize
ALSA: usb-audio: avoid setting of sample rate multiple times on bus
ASoC: cs35l34: Simplify the logic to set CS35L34_MCLK_CTL setting
ALSA: hda - Gate the mic jack on HP Z1 Gen3 AiO
ALSA: hda: when comparing pin configurations, ignore assoc in addition to seq
...
|
|
We can no longer rely on the return value of
devm_snd_dmaengine_pcm_register(...) to check if the DMA
handle is declared in the DT.
Previously this check activated PIO mode but currently
dma_request_chan returns either a valid channel or -EPROBE_DEFER.
In order to activate PIO mode check instead if the interrupt
line is declared. This reflects better what is documented in
the DT bindings (see Documentation/devicetree/bindings/sound/
designware-i2s.txt).
Also, initialize use_pio variable which was never being set
causing PIO mode to never work.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'asoc/topic/zte' into asoc-next
|
|
'asoc/topic/wm8978', 'asoc/topic/wm9081' and 'asoc/topic/wm9705' into asoc-next
|
|
'asoc/topic/topology', 'asoc/topic/uda1380', 'asoc/topic/wm2200' and 'asoc/topic/wm8523' into asoc-next
|
|
'asoc/topic/sti-codec', 'asoc/topic/sunxi' and 'asoc/topic/tegra' into asoc-next
|
|
'asoc/topic/rt5677', 'asoc/topic/samsung' and 'asoc/topic/simple' into asoc-next
|
|
'asoc/topic/rt5640', 'asoc/topic/rt5660' and 'asoc/topic/rt5663' into asoc-next
|
|
'asoc/topic/rockchip', 'asoc/topic/rt286' and 'asoc/topic/rt298' into asoc-next
|
|
'asoc/topic/qcom' and 'asoc/topic/rk808' into asoc-next
|
|
'asoc/topic/max98504' and 'asoc/topic/nau8825' into asoc-next
|
|
'asoc/topic/extcon' and 'asoc/topic/fsl' into asoc-next
|
|
'asoc/topic/cs42l73' and 'asoc/topic/cs42xx8' into asoc-next
|
|
'asoc/topic/cs35l34' into asoc-next
|
|
'asoc/topic/atmel', 'asoc/topic/bcm' and 'asoc/topic/bitfield' into asoc-next
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
into asoc-linus
|
|
|
|
buf was allocated by kzalloc() so it should be passed to kfree()
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When num_kcontrols is zero, widget->dobj.widget.kcontrol_type
gets set to an uninitialized local variable:
sound/soc/soc-topology.c: In function 'soc_tplg_dapm_widget_create':
sound/soc/soc-topology.c:1566:36: error: 'kcontrol_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I could not figure out which of the valid types would be appropriate
here, so this sets it to '0', which is invalid but at least well-defined
here. There is probably a better way to address the issue.
Fixes: eea3dd4f1247 ("ASoC: topology: Only free TLV for volume mixers of a widget")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The macro ZX_SPDIF_CLK_RAT should be 2 instead of 4. With this
fix, we can get correct audio output on HDMI through SPDIF interface.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ZTE ZX SPDIF and I2S drivers can work on not only ZX296702 but also
other ZTE ZX family SoCs like ZX296718, which is an arm64 platform.
Let's make a few renaming and tweak the Kconfig a bit to get the drivers
available for other ZTE ZX platforms.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current rsnd driver setups BRGCKR/BRRA/BRRB when .probe timing.
But it breaks sound after Suspend/Resume. These should be setups
every start timing.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current rsnd driver enables ADG clock when .probe timing,
but it breaks sound after Suspend/Resume. These should be setups
every suspend/resume timing too.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ssi->usrcnt will be updated on snd_soc_dai_ops::trigger,
but snd_pcm_ops::hw_params will be called *before* it.
Thus, ssi->usrcnt is still 0 when 1st call.
rsnd_ssi_hw_params() needs to check its called count, this means
trigger should be if (ssi->usrcnt) instead of if (ssi->usrcnt > 1).
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
