| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
'asoc/topic/fsl', 'asoc/topic/fsl-asrc' and 'asoc/topic/fsl-esai' into asoc-next
|
|
ESAI need to enable the spba clock, when sdma is using share peripheral
script. In this case, there is two spba master port is used, if don't
enable the clock, the spba bus will have arbitration issue, which may
cause read/write wrong data from/to ESAI registers.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
using params_width function to simplify code.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ETDR and TX0~5 registers are writable and not readable. So they are non
volatile. Remove them from volatile list, and add default register value for
them.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Change them to #ifdef as CONFIG_PM_SLEEP might not be defined at all.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For i.MX6 SoloX, there is a mode of the SoC to shutdown all power source of
modules during system suspend and resume procedure. Thus, ESAI needs to save
all the values of registers before the system suspend and restore them after
the system resume.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There are little changes in core part, but lots of development are
found in drivers, especially ASoC. The diffstat shows regmap-related
changes for a slight API additions / changes, and that's all.
Looking at the code size statistics, the most significant addition is
for Intel Skylake. (Note that SKL support is still underway, the
codec driver is missing.) Also STI controller driver is a major
addition as well as a few new codec drivers.
In HD-audio side, there are fewer changes than the past. The
noticeable change is the support of ELD notification from i915
graphics driver. Thus this pull request carries a few changes in
drm/i915.
Other than that, USB-audio got a rewrite of runtime PM code. It was
initiated by lockdep warning, but resulted in a good cleanup in the
end.
Below are the highlights:
Common:
- Factoring out of AC'97 reset code from ASoC into the core helper
- A few regmap API extensions (in case it's not pulled yet)
ASoC:
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650
- Initial driver support for Intel Skylake devices
- Lots of rsnd cleanup and enhancements
- A few DAPM fixes and cleanups
- A large number of cleanups in various drivers (conversion and
standardized to regmap, component) mostly by Lars-Peter and Axel
HD-audio:
- Extended HD-audio core for Intel Skylake controller support
- Quirks for Dell headsets, Alienware 15
- Clean up of pin-based quirk tables for Realtek codecs
- ELD notifier implenetation for Intel HDMI/DP
USB-audio:
- Refactor runtime PM code to make lockdep happier"
* tag 'sound-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (411 commits)
drm/i915: Add locks around audio component bind/unbind
drm/i915: Drop port_mst_index parameter from pin/eld callback
ALSA: hda - Fix missing inline for dummy snd_hdac_set_codec_wakeup()
ALSA: hda - Wake the codec up on pin/ELD notify events
ALSA: hda - allow codecs to access the i915 pin/ELD callback
drm/i915: Call audio pin/ELD notify function
drm/i915: Add audio pin sense / ELD callback
ASoC: zx296702-i2s: Fix resource leak when unload module
ASoC: sti_uniperif: Ensure component is unregistered when unload module
ASoC: au1x: psc-i2s: Convert to use devm_ioremap_resource
ASoC: sh: dma-sh7760: Convert to devm_snd_soc_register_platform
ASoC: spear_pcm: Use devm_snd_dmaengine_pcm_register to fix resource leak
ALSA: fireworks/bebob/dice/oxfw: fix substreams counting at vmalloc failure
ASoC: Clean up docbook warnings
ASoC: txx9: Convert to devm_snd_soc_register_platform
ASoC: pxa: Convert to devm_snd_soc_register_platform
ASoC: nuc900: Convert to devm_snd_soc_register_platform
ASoC: blackfin: Convert to devm_snd_soc_register_platform
ASoC: au1x: Convert to devm_snd_soc_register_platform
ASoC: qcom: Constify asoc_qcom_lpass_cpu_dai_ops
...
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
As the ssi is not the only cpu dai, there are esai, spdif, sai.
and imx_pcm_dma can be used by all of them. Especially ESAI need
a larger DMA buffer size. So Add dedicated DMA buffer for each cpu
dai.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
|
The driver previously used 32-bit fixed slot width as default.
In result, ESAI might use 32-bit length to capture 16-bit width
audio slot from CODEC side when ESAI is running as DAI slave.
So this patch just removes the default slot_width so as to use
dynamic slot width. If there comes a specific situation that
needs a fixed width, the machine driver shall set slot_width
via set_tdm_slot() so as to let the ESAI driver replace the
dynamic width policy with the fixed value.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into driver-core-next
Remove all .owner fields from platform drivers
|
|
Use strncpy() instead of strcpy(). That's not a security issue, as the
source buffer is taken from DT nodes, but we should still enforce bound
checks. Spotted by Coverity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-fsl-esai
|
|
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-fsl-esai
|
|
Original driver didn't store the number of slots, just fix the slot number
to 2, use this default number to calculate bclk and pins for TX/RX.
In this patch, add one parameter for slots, and update the calculation of
bclk and pins of TX/RX. Then driver will be compatible with slots > 2 in
TDM mode.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This reverts commit a603c8ee526f5ea9ad9b40710308766299ad8a69.
fsl_asoc_xlate_tdm_slot_mask() is different with snd_soc_xlate_tdm_slot_mask().
fsl_asoc_xlate_tdm_slot_mask() will set the enabled bit to 0, disabled bit
to 1. snd_soc_xlate_tdm_slot_mask() will set the enabled bit to 1, disabled
bit to 0.
For esai when the bit value is 1, the slot is enabled, when the bit value is 0,
the slot is disabled. If using fsl_asoc_xlate_tdm_slot_mask(), the esai will
work abnormally. So revert this patch, make the esai use default function.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
DPCM needs extra dapm routes in the machine driver to route audio
between Front-End and Back-End. In order to differ the stream names
in the route map from CODECs, we here add specific stream names to
ESAI driver so that we can implement ASRC via DPCM to it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
'asoc/topic/fsl-esai', 'asoc/topic/fsl-sai', 'asoc/topic/fsl-spdif' and 'asoc/topic/fsl-ssi' into asoc-next
|
|
We don't need to change those dividers if bclk and mclk remains the same
directions and values.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
According to Reference Manual -- ESAI Initialization chapter, as the
standard procedure of ESAI personal reset, the PCRC and PRRC registers
should be remained in its reset value and then configured after T/RCCR
and T/RCR configurations's done but before TE/RE's enabling.
So this patch moves PCRC and PRRC settings to the end of hw_params().
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
ESAI can only output EXTAL clock source directly. But for FSYS clock source,
ESAI can not output it without getting through PSR PM dividers.
So this patch adds an extra check in the code.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The range here from 1 to 16 is confined to FP divider only while the
sck_div indicates if the calculation contains PSR and PM dividers. So
for the case using PSR and PM since the sck_div is true, the range of
ratio would simply become bigger than 16.
So this patch fixes the condition here and adds one line comments to
make the purpose here clear.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Use the precise definition of 'ret', which will be used for
the error check.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch add .xlate_tdm_slot_mask support for ESAI, and this will
generate the TDM slot TX and RX masks.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
'asoc/topic/da9055', 'asoc/topic/davinci', 'asoc/topic/fsl', 'asoc/topic/fsl-esai', 'asoc/topic/fsl-sai' and 'asoc/topic/fsl-spdif' into asoc-next
|
|
For most platforms, the CPU and ESAI device is in the same endianess
mode. While for the LS1 platform, the CPU is in LE mode and the ESAI
is in BE mode.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch implements a device-tree-only CPU DAI driver for Freescale ESAI
controller that supports:
- 12 channels playback and 8 channels record.
[ Some of the inner transmitters and receivers are sharing same group of
pins. So the maxmium 12 output or 8 input channels are only valid if
there is no pin conflict occurring to it. ]
- Independent (asynchronous mode) or shared (synchronous mode) transmit and
receive sections with separate or shared internal/external clocks and frame
syncs, operating in Master or Slave mode.
[ Current ALSA seems not to allow CPU DAI drivers to configure DAI format
separately for PLAYBACK and CAPTURE. So this first version only supports
the case that uses the same DAI format for both directions. ]
- Various DAI formats: I2S, Left-Justified, Right-Justified, DSP-A and DSP-B.
- Programmable word length (8, 16, 20 or 24bits)
- Flexible selection between system clock or external oscillator as input
clock source, programmable internal clock divider and frame sync generation.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
