| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When the record starts, the driver turns on MICBIAS and the voltage is
pulled up for an instant. If the receiver starts to capture the signal
between the instant, there is an pop noise in the stream beginning.
To avoid the pop noise, the driver makes a delay in the sequence.
After MICBIAS powered up, the driver waits 300 ms for the voltage
going down. Then turns on the ADC output, and sends signal to receiver.
The pop noise can be erased.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Change channel PGA input mode selection for better recording quality.
The patch shorts the inputs to ground with 12kOhm differentially
terminated.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The four channel ADCs in NAU85L40 have difference control registers,
it is hard to synchronous these four channels without correct sequence.
The phase difference will not be a constant and not to conjecture easily.
It may be 2.55 degree, or more ,or less.
Intended to prevent phase difference of channels, the solution as follows:
(1)Channel_Sync need to be enabled.
(2)Do soft reset without affecting register when recording done.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the option for the DSP clock that can be calibrated by the other clock
source.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After checking the code and the datasheet, it seems like we are handling
the clock inversion (SND_SOC_DAIFMT_NB_IF and SND_SOC_DAIFMT_IB_IF) not
correctly.
>From the datasheet (Table 58):
R5 Format Control, BITS[5:4], [BCP:LRP]:
(0) 00 = normal BCLK, normal LRCLK
(1) 01 = normal BCLK, inverted LRCLK <-- Fix this
(2) 10 = inverted BCLK, normal LRCLK
(3) 11 = inverted BCLK, inverted LRCLK <-- Fix this
Signed-off-by: Sergej Sawazki <sergej@taudac.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The patch fixed that the ACPI cannot access the device property from the
function rt5514_parse_dp().
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'asoc/fix/rt5514', 'asoc/fix/rt5616', 'asoc/fix/rt5659' and 'asoc/fix/rt5663' into tmp
|
|
"SPOL MIX DAC R1 Switch" and "SPOL MIX SPKVOL R Switch" are only
exist in the early version of rt5645.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This reverts commit 60d5a1a47b9a8381c08d2263b11ac9c757c87746.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The KIANO SlimNote 14.2 laptop uses the JD1_1 input pin for jack
detection. Set the correct quirk in the codec driver.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rework a bit the quirk logic in the codec driver to simplify the
DMI-based quirk assignment for non-DT platforms.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Enable jack detection for the RT5651 codec on the JD* pins.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In preparation for unconditionally passing the struct timer_list
pointer to all timer callbacks, switch to using the new timer_setup()
and from_timer() to pass the timer pointer explicitly. These are all the
"mechanical" changes remaining in the sound subsystem.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
into asoc-linus
|
|
'asoc/fix/rt5659', 'asoc/fix/rt5663', 'asoc/fix/samsung' and 'asoc/fix/stm32' into asoc-linus
|
|
'asoc/fix/max98090' into asoc-linus
|
|
Enable jack detection for the RT5651 codec on the JD* pins.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
MICBIAS widget type has been deprecated. Convert it to a SUPPLY widget.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The default value of register 0x91 is 0x0c00 instead of 0x0000.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move set_pll function to codec level and people can use it at both
codec and dai level.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move set_sysclk to codec level and people can use it at both
codec and dai level.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
"Charge Pump" is necessary for "LOUT Amp".
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a power bit for LOUT Amp.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the old AC97 is not used, CONFIG_SND_SOC_AC97_BUS is not
defined. As a consequence, in the error path, snd_soc_free_ac97_codec()
is not defined and triggers a compilation error.
Fix it for wm9705 and wm9712, as wm9713 is correctly written.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Return proper error instead of 0 if the revision does not match.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The macro used to set the microphone bias level causes the
snd_soc_write() call to overwrite other fields in the CDC_A_MICB_1_VAL
register. The macro also does not return the proper level value
to use. This fixes this by preserving all bits from the register
that are not the level while setting the level.
Signed-off-by: Jean-François Têtu <jean-francois.tetu@savoirfairelinux.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The very first time a headset is plugged in, detection is unreliable
because bias hasn't been configured yet, it's done once a mechanical
insertion interrupt has been triggered, so following insertions (and
thus detections) are not affected.
To fix the very first detection, the bias must also be configured in the
function that setup the MBHC. Move pm8916_wcd_setup_mbhc after
pm8916_mbhc_configure_bias to avoid a forward declaration.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo snd_soc_msm8916_analog | grep alias
$
After this patch:
$ modinfo snd_soc_msm8916_analog | grep alias
alias: of:N*T*Cqcom,pm8916-wcd-analog-codecC*
alias: of:N*T*Cqcom,pm8916-wcd-analog-codec
Signed-off-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
msm8916-wcd-analog uses button0 to differentiate between headphone and
headset. Under some circumstances, button pressed and released
interrupts are not fired as the driver expects it.
For instance, with some connectors, there are spurious button-pressed
interrupts when unplugging a headphone, without the corresponding
button-released interrupt. But the codec always alternates between
button pressed and released interrupts, it cannot fire two interrupts of
the same kind in a row. That means that when the headphone is plugged
back, only a button-released interrupt will be fired instead of pressed
then released. This causes the driver to report headphone as headset.
By changing the logic and relying on button 0 release interrupt, the
driver could be made more robust for connectors that differ from the one
used on the Dragonboard's audio mezzanine.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We need to set a specific bit for 50 bclk rate. So add set_bclk_ratio
function to set the bit.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The kcontrol for the third input (rxN_mix1_inp3) of both RX2
and RX3 mixers are not using the correct control register. This simple
patch fixes this.
Signed-off-by: Jean-François Têtu <jean-francois.tetu@savoirfairelinux.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Additional checks exposed a mistake in the quirk for the Dell Venue
Pro 5855 (Dmic2 instead of Dmic1). Rather than adding quirk tables,
merge all quirks in a single table and use flags to differentiate
platforms. Also add a parameter override to help support additional
platforms using this codec
CC: Bard Liao <bardliao@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the irq handler "rt5663_irq", while the codec is not initialized,
rt5663->codec will be null, and it will cause the kernel panic in the debug
print enabled.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently, wm8998 has two input mux controls on IN1 and attempts to
switch these together when the A position is configured to be in digital
mode. This is because the digital mode requires pins from both the L and
R channels. However, this doesn't work as intended because whilst the
registers on the chip are changed the corresponding DAPM
representation is only updated for the mux actually being changed by the
user. The DAPM graph being out of sync with the hardware can cause some
odd issues with incorrect things being powered etc.
To avoid this issue and simplify the code somewhat, simply let the user
set the muxes as they desire. If they set an invalid configuration they
might not get audio from the DMIC but most of the chip requires you to
set a valid audio route to get audio.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The output volume limits allow signals to be limited to specific levels
appropriate for the hardware attached. As this is a property of the
hardware itself these will be configured through device tree.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Don't use BUG_ON() for a non-critical sanity check on production
systems. This patch replaces with a softer WARN_ON() and an error
path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Even though the tfa9879 driver can probe via device tree trough the
I2C core code, it is preferable to have explicit device tree
bindings instead [1], so add this support.
[1] https://www.spinics.net/lists/devicetree/msg195176.html
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Don't populate the read-only arrays div and pd on the stack,
instead make them static const. Makes the object code smaller by 210 bytes:
Before:
text data bss dec hex filename
2869 720 0 3589 e05 sound/soc/codecs/rl6231.o
After:
text data bss dec hex filename
2495 880 0 3375 d2f sound/soc/codecs/rl6231.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for the new ac97 bus model, where devices are automatically
discovered on AC-Links.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a private data structure. This is a preparation for a codec which
would need an another data on top of snd_ac97, which will be the case
when an MFD wm97xx device will probe wm9705.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for the new ac97 bus model, where devices are automatically
discovered on AC-Links.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for the new ac97 bus model, where devices are automatically
discovered on AC-Links.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently all the audio related device tree entries are handled by the
MFD code, for most parts of the Arizona driver we group the device
tree handling with the component that uses it and should do so here as
well.
Add handling in the ASoC code for the audio device tree entries, a
later patch removes the MFD side handling but there is no harm in it
being duplicated temporarily.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the driver has quite a few small initialisation functions, in
preparation for some refactoring add a new function arizona_init_common.
This will be used bus probe level initialisation that is common across
Arizona devices. For now just move the notifier chain initialisation in
there.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
