summaryrefslogtreecommitdiff
path: root/sound/soc/codecs/twl4030.c
AgeCommit message (Collapse)AuthorFilesLines
2009-04-23ASoC: TWL4030: Add 4 channel TDM supportPeter Ujfalusi1-2/+50
Support for 4 channel TDM (SND_SOC_DAIFMT_DSP_A) for twl4030 codec. The channel allocations are: Playback: TDM i2s TWL RX Channel 1 Left SDRL2 Channel 3 Right SDRR2 Channel 2 -- SDRL1 Channel 4 -- SDRR1 Capture: TDM i2s TWL TX Channel 1 Left TXL1 Channel 3 Right TXR1 Channel 2 -- TXL2 Channel 4 -- TXR2 Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-23ASoC: TWL4030: Add VDL path supportJoonyoung Shim1-130/+126
Add DAPMs for VDL(Voice Down Link) path. To support VDL path, we have to change DAPMs of outputs(Earpiece, PreDrive Left/Right, Headset Left/Right, Carkit Left/Right) from mux to mixer. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-20ASoC: TWL4030: Add support Voice DAIJoonyoung Shim1-5/+168
Add Voice DAI to support the PCM voice interface of the twl4030 codec. The PCM voice interface can be used with 8-kHz(voice narrowband) or 16-kHz(voice wideband) sampling rates, and 16bits, and mono RX and mono TX or stereo TX. The PCM voice interface has two modes - PCM mode1 : This uses the normal FS polarity and the rising edge of the clock signal. - PCM mode2 : This uses the FS polarity inverted and the falling edge of the clock signal. If the system master clock is not 26MHz or the twl4030 codec mode is not option2, the voice PCM interface is not available. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-17ASoC: TWL4030: Fix for the constraint handlingPeter Ujfalusi1-19/+66
The original implementation of the constraints were good against sane applications. If the opening sequence is: stream1_open, stream1_hw_params, stream2_open, stream2_hw_params -> the constraints are set correctly for stream2. But if the sequence is: stream1_open, stream2_open, stream2_hw_params, stream1_hw_params -> than stream2 would receive constraint rate = 0, sample_bits = 0, since the stream1 has not yet called hw_params... The command to trigger this event: gst-launch-0.10 alsasrc device=hw:0 ! alsasink device=hw:0 sync=false This patch does some 'black magic' in order to always set the correct constraints and sets it only when it is needed for the other stream. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-07ASoC: TWL4030: Compillation error fixPeter Ujfalusi1-4/+6
Fix for compillation error introduced by the constrain patch. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-03ASoC: TWL4030: Add actual support for 96KHz playback supportPeter Ujfalusi1-0/+3
Adds the needed code to be able to use 96KHz playback. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-02ASoC: TWL4030: Add constrains for second streamPeter Ujfalusi1-0/+54
In case of duplex mode (capture and playback at the same time), the second stream has to have the same parameters (rate, sample size) as the already running stream. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-02ASoC: TWL4030: 96KHz playback supportPeter Ujfalusi1-1/+1
TWL4030 supports 96KHz sample playback, but only playback. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-03-16ASoC: twl4030 - Fix build errorJoonyoung Shim1-5/+7
CC sound/soc/codecs/twl4030.o sound/soc/codecs/twl4030.c:1400: warning: braces around scalar initializer sound/soc/codecs/twl4030.c:1400: warning: (near initialization for 'twl4030_dai.ops') sound/soc/codecs/twl4030.c:1401: error: field name not in record or union initializer sound/soc/codecs/twl4030.c:1401: error: (near initialization for 'twl4030_dai.ops') sound/soc/codecs/twl4030.c:1401: warning: initialization from incompatible pointer type sound/soc/codecs/twl4030.c:1402: error: field name not in record or union initializer sound/soc/codecs/twl4030.c:1402: error: (near initialization for 'twl4030_dai.ops') sound/soc/codecs/twl4030.c:1402: warning: excess elements in scalar initializer sound/soc/codecs/twl4030.c:1402: warning: (near initialization for 'twl4030_dai.ops') sound/soc/codecs/twl4030.c:1403: error: field name not in record or union initializer sound/soc/codecs/twl4030.c:1403: error: (near initialization for 'twl4030_dai.ops') sound/soc/codecs/twl4030.c:1403: warning: excess elements in scalar initializer sound/soc/codecs/twl4030.c:1403: warning: (near initialization for 'twl4030_dai.ops') Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-03-06ASoC: TWL4030: Make the HS ramp delay configurablePeter Ujfalusi1-4/+14
Enum type for selecting the desired ramp delay for the headset output. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-02-18ASoC: TWL4030: Add digital loopback supportPeter Ujfalusi1-6/+50
This patch adds the digital loopback/bypass support for twl4030 codec. The digital loopback will let the digimic0 (routed in the TX1 capture path inside of TWL4030) data to be routed back to the RX2 playback path (I2S stereo). It can also route the analog capture date routed through the TX1 back to RX2. Effectively the digital loopback is routing the audio from the TX1 capture path to the RX2 playback path. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-29ASoC: TWL4030: Add analog loopback supportPeter Ujfalusi1-13/+199
This patch adds the analog loopback/bypass support for twl4030 codec. Details for the implementation: It seams that the analog loopback needs the DAC powered on on the channel, where the loopback is selected. The switch for the DACs has been moved from the DAPM_DAC to the "Analog XX Playback Mixer". In this way the DAC will be powered while the audio playback is used or/and the loopback is enabled for the channel. The twl4030 codec powering has been reworked. Now the codec will be powered as long as it does not receives the SND_SOC_BIAS_OFF event. The exceptions are when the given change in the registers needs the codec power down/up cycle in order to take effect. Otherwise the codec is on. When the codec enters to STANDBY state and none of the loopback paths are enabled, than the amplifiers, which are no in the DAPM path are forced to turn off and the PLL is disabled. When playback/capture starts the disabled gains are restored and the PLL is enabled. When one of the loopback enabled in STANDBY mode, the disabled gains are restored and the PLL is enabled also. In short: the codec always goes to the lowest power state based on the bias_level and the bypass_state. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-27ASoC: TWL4030: Move the twl4030_power_up and _power_down functionPeter Ujfalusi1-43/+42
Move the twl4030_power_up and twl4030_power_down function earlier to facilitate the analog bypass implementation. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-27ASoC: TWL4030: Physical ADC and amplifier power switch changePeter Ujfalusi1-13/+13
Change the power switches for the physical ADC and for the amplifiers for the analog capture path to map more closely the actual path inside of the codec. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-27ASoC: TWL4030: Enable Headset Left anti-pop/bias ramp only if the Headset ↵Peter Ujfalusi1-26/+45
Left is in use The Headset Left anti-pop and bias ramp does not need to be enabled, if the headset is not in use. Move the code to DAPM event handler for HeadsetL. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-27ASoC: TWL4030: Code clean up for codec power up and downPeter Ujfalusi1-26/+17
Merge the codec up and down functions to a simple one. Codec is powered down by default (reg_cache change). Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-27ASoC: TWL4030: Syncronize the reg_cache for ANAMICL after the offset cancelationPeter Ujfalusi1-0/+3
The offset cancelation bit in ANAMICL register is self cleanig. Make sure that the reg_cache holds the same value as the HW register. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-27ASoC: Push the codec runtime storage into the card structureMark Brown1-6/+6
This is a further stage on the road to refactoring away the ASoC platform device. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-19ASoC: fixes to caching implementationsIan Molton1-0/+3
This patch takes fixes a number of bugs in the caching code used by several ASoC codec drivers. Mostly off-by-one fixes. Signed-off-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-09Merge branch 'for-2.6.29' into for-2.6.30Mark Brown1-5/+7
2009-01-09ASoC: TWL4030: Module unloading fixPeter Ujfalusi1-0/+2
Call the snd_soc_free_pcm and snd_soc_dapm_free when the codec driver is unloaded. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-09ASoC: cleanup duplicated code.Ian Molton1-17/+2
Many codec drivers were implementing cookie-cutter copies of the function that adds kcontrols to the codec. This patch moves this code to a common function snd_soc_add_controls() in soc-core.c and updates all drivers using copies of this function to use the new common version. [Edited to raise priority of error log message and document parameters. -- broonie] Signed-off-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-08ASoC: TWL4030: Change the soc_value_enum back to soc_enumPeter Ujfalusi1-5/+5
The soc_value_enum has been merged to soc_enum. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-01-05ASoC: TWL4030: Convert the bitfield enums to VALUE_ENUM typePeter Ujfalusi1-63/+55
Convert the bitfield coded enums to the new VALUE_ENUM type. Remove the enum check, since the VALUE_ENUM type can handle the bitfield coding and also handles the 'holes' in the bitfield. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-31ASoC: TWL4030: DAPM based capture implementationPeter Ujfalusi1-172/+175
This patch adds DAPM implementaion for the capture path on twlx030. TWL has two physical ADC and two digital microphone (stereo) connections. The CPU interface has four microphone channels. For simplicity the microphone channel paths are named as: TX1 (Left/Right) - when using i2s mode, only the TX1 data is valid TX2 (Left/Right) Input routing (simplified version): There is two levels of mux settings for TWL in input path: Analog input mux: ADCL <- {Off, Main mic, Headset mic, AUXL, Carkit mic} ADCR <- {Off, Sub mic, AUXR} Analog/Digital mux: TX1 Analog mode: TX1L <- ADCL TX1R <- ADCR TX1 Digital mode: TX1L <- Digimic0 (Left) TX1R <- Digimic0 (Right) TX2 Analog mode: TX2L <- ADCL TX2R <- ADCR TX2 Digital mode: TX2L <- Digimic1 (Left) TX2R <- Digimic1 (Right) The patch provides the following user controls for the capture path: Mux settings: "TX1 Capture Route": {Analog, Digimic0} "TX2 Capture Route": {Analog, Digimic1} "Analog Left Capture Route": {Off, Main Mic, Headset Mic, AUXL, Carkit Mic} "Analog Right Capture Route": {Off, Sub Mic, AUXR} Volume/Gain controls: "TX1 Digital Capture Volume": Stereo gain control for TX1 path "TX2 Digital Capture Volume": Stereo gain control for TX2 path "Analog Capture Volume": Stereo gain control for the analog path only Important things for the board files: Microphone bias: "Mic Bias 1": Bias for Main mic or for digimic0 (analog or digital path) "Mic Bias 2": Bias for Sub mic or for digimic1 (analog or digital path) "Headset Mic Bias": Bias for Headset mic When the routing configured correctly only the needed components will be powered/enabled. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-31ASoC: TWL4030: Make the enum filter generic for twl4030Peter Ujfalusi1-16/+14
Modify the enum filter to more generic that it will filter out the enums with text "Invalid". The enum filter also required for the capture path. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-11ASoC: TWL4030: hands-free start-up sequence.Stanley.Miao1-4/+30
A special start-up sequence is required to reduce the pop-noise of Class D amplifier when enable hands-free on TWL4030. Signed-off-by: Stanley.Miao <stanley.miao@windriver.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-10ASoC: TWL4030: Change the name for the DACsPeter Ujfalusi1-8/+8
To avoid confusion the names for the DACs changed: DACL1 -> DAC Left1 ... Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-10ASoC: TWL4030: Small cleanupPeter Ujfalusi1-6/+3
The mux switch related texts fits to on line, no need to wrap them. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-10ASoC: TWL4030: Add missing Carkit outputPeter Ujfalusi1-0/+2
SND_SOC_DAPM_OUTPUT definition for carkitL/R was missing. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-10ALSA: ASoC - Fix module init entry for twl4030.cTakashi Iwai1-2/+2
Fixed the function name of module init entry for twl4030.c, which conflicted with the existing hardware init function: sound/soc/codecs/twl4030.c:1278: error: conflicting types for 'twl4030_init' sound/soc/codecs/twl4030.c:1187: error: previous definition of 'twl4030_init' was here Also fixed the section type of init function. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-12-09ASoC: Register non-AC97 codec DAIsMark Brown1-1/+13
Currently this is done at module probe time since ASoC ties in codec device probe to the instantiation of the entire ASoC device. Subsequent patches will refactor the codec drivers to handle probing separately. Note that the core does not yet use this information. AC97 is special since the codec is controlled over the AC97 link but we want to give the machine driver a chance to set up the system before trying to instantiate since it may need to do configuration before the AC97 link will operate Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-09ASoC: TWL4030: Do not alter the Headset output volume on power-up/downPeter Ujfalusi1-10/+2
There is a separate gain control for the Headset output already. Do not reset the gain to 0 dB at power up. In power-down, there is no need to set the Headset output gain to power-down mode, since if the CODECPDZ is in powered off this setting has no effect. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-09ASoC: TWL4030: DAPM mapping of the Handsfree outputsPeter Ujfalusi1-0/+41
Adds DAPM muxing, routing for the Handsfree outputs. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-09ASoC: TWL4030: DAPM mapping of the Carkit outputsPeter Ujfalusi1-0/+37
Adds DAPM muxing, routing for the Carkit outputs. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-09ASoC: TWL4030: DAPM mapping of the Headset outputsPeter Ujfalusi1-0/+39
Adds DAPM muxing, routing for the Headset outputs. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-09ASoC: TWL4030: DAPM mapping of the PreDriv outputsPeter Ujfalusi1-0/+45
Adds DAPM muxing, routing for the PreDrive outputs. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-09ASoC: TWL4030: DAPM mapping of the Earpiece outputPeter Ujfalusi1-0/+27
Adds DAPM muxing, routing for the Earpiece output. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-09ASoC: TWL4030: Add DAPM event handler for output MUX selectionPeter Ujfalusi1-0/+24
DAPM event handler is set to filter out invalid MUX settings for certain outputs. Earpiece: - 0 = Off - 1 = DACL1 - 2 = DACL2 - 3 = *** Invalid *** - 4 = DACR1 PreDriveL/R: - 0 = Off/Off - 1 = DACL1/DACR1 - 2 = DACL2/DACR2 - 3 = *** Invalid/Invalid *** - 4 = DACR2/DACL2 Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-09ASoC: TWL4030: Add Analog PGA control switch to DAPMPeter Ujfalusi1-2/+23
Add all four APGA switch to DAPM routing and widgets. Add user control for DA enable for all APGA as normal control. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-09ASoC: TWL4030: Correct DAPM_DAC with power controlPeter Ujfalusi1-4/+11
Add all four DACs to dapm_widgets with power switch. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-03ASoC: TWL4030: Add input selection and gain controlsGrazvydas Ignotas1-3/+174
The TWL4030 codec device has two ADCs. Both of them can have several inputs routed to them, but TRM says that only one source can be selected for every ADC, even though every source has a dedicated bit in the registers. This patch adds input source controls. It modifies default register values to have no inputs selected and ADCs disabled. When some input is selected, control handlers enable apropriate input amplifier and ADC. If a microphone is selected, bias power is automatically enabled. When some input is deselected, unused chip parts are disabled. Microphone and line input recording tested on OMAP3 pandora board. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-01ASoC: TWL4030: Add volume controls for outputsPeter Ujfalusi1-0/+21
All outputs have dedicated gain controls except the HandsFree output. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-01ASoC: TWL4030: Change the common playback volume controlsPeter Ujfalusi1-8/+29
Add Playback volume controls for all four DACs. All four paths has three levels of volume controls: Digital Fine gain, Digital Coarse gain, Analog gain. The controls are named to reflect their connection to the DACs. Per DAC volume can be performed, if needed: amixer sset 'DAC1 Analog' 5,10 DACL1 analog gain to 5 DACR1 analog gain to 10 Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-01ASoC: TWL4030: Change the capture volume control to TLVPeter Ujfalusi1-3/+11
The digital Capture gain control has a range: 0 to 31 dB in 1 dB steps. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-12-01ASoC: Rename snd_soc_register_card() to snd_soc_init_card()Mark Brown1-1/+1
Currently ASoC card initialisation is completed by a function called snd_soc_register_card(). As part of the work to allow independant registration of cards, codecs and machines in ASoC v2 a new function of the same name has been added so rename the existing function to facilitate the merge of v2. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-11-24ASoC: TWL4030: Add helper function for output gain controlsPeter Ujfalusi1-0/+157
Some of the gain controls in TWL (mostly those which are associated with the outputs) are implemented in an interesting way: 0x0 : Power down (mute) 0x1 : 6dB 0x2 : 0 dB 0x3 : -6 dB Inverting not going to help with these. Custom volsw and volsw_2r get/put functions to handle these gains. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-11-24ASoC: TWL4030: Add CGAIN volume controlPeter Ujfalusi1-0/+10
Add CGAIN (Coarse gain control) to TWL4030 codec. The range of the CGAIN is: 0 dB to 12 dB in 6 dB steps. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-11-24ASoC: TWL4030: Change the Master volume control to TLVPeter Ujfalusi1-2/+9
TWL4030 FGAIN volume control has a range: -62 to 0 dB in 1 dB steps, 0 in the FGAIN means mute. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2008-11-24ASoC: TWL4030: Disable soft-volumePeter Ujfalusi1-1/+1
Keep Soft-volume disabled for now, since if it is enabled the FGAIN volume controls are not working in the current configuration: CODEC_MODE:OPT_MODE = 1 OPTION:ARXR2_EN = 1 OPTION:ARXL2_EN = 1 OPTION:ARXR1_EN = 0 OPTION:ARXL1_VRX_EN = 0 RX_PATH_SEL:RXL1_SEL = 0x0 (or 0x1) RX_PATH_SEL:RXR1_SEL = 0x0 (or 0x1) After the patch, FGAIN volume control works. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-27 13:23:35 +0300