Age | Commit message (Collapse) | Author | Files | Lines |
|
* topic/hdsp:
ALSA: hdsp - Add a comment about external firmwares for hdsp
ALSA: hdsp: allow firmware loading from inside the kernel
|
|
* topic/hda: (51 commits)
ALSA: hda - Fix the previous tagra-8ch patch
ALSA: hda - Add 7.1 support for MSI GX620
ALSA: support Sony Vaio TT
ALSA: hda_intel: fix build error when !PM
ALSA: hda - More Aspire 8930G fixes
ALSA: hda - Acer Aspire 8930G support
ALSA: hda - Limit codec-verb retry to limited hardwares
ALSA: hda - Add codec bus reset and verb-retry at critical errors
ALSA: hda - Reorder and clean-up ALC268 quirk table
ALSA: hda - fix audio on LG R510
ALSA: hda - Macbook[Pro] 5 6ch support
ALSA: hda-intel: improve initialization for ALC262_HP_BPC model
ALSA: hda - Jack Mode changes for Sigmatel boards
ALSA: hda - Support NVIDIA 8 channel HDMI audio
ALSA: hda - Fix a typo in the previous patch
ALSA: hda - Fix reverted LED setup for HP
ALSA: hda - Add more register bits definitions
ALSA: hda - Always sync writes in single_cmd mode
ALSA: hda - Support sync after writing a verb
ALSA: hda - Allow concurrent RIRB access in single_cmd mode
...
|
|
* topic/emu10k1:
ALSA: emu10k1 - Fix minimum periods for efx playback
|
|
* topic/div64-cleanup:
ALSA: Clean up 64bit division functions
|
|
* topic/ctxfi: (35 commits)
ALSA: ctxfi - Clear PCM resources at hw_params and hw_free
ALSA: ctxfi - Check the presence of SRC instance in PCM pointer callbacks
ALSA: ctxfi - Add missing start check in atc_pcm_playback_start()
ALSA: ctxfi - Add use_system_timer module option
ALSA: ctxfi - Fix wrong model id for UAA
ALSA: ctxfi - Clean up probe routines
ALSA: ctxfi - Fix / clean up hw20k2 chip code
ALSA: ctxfi - Fix possible buffer pointer overrun
ALSA: ctxfi - Remove useless initializations and cast
ALSA: ctxfi - Fix DMA mask for emu20k2 chip
ALSA: ctxfi - Make volume controls more intuitive
ALSA: ctxfi - Optimize the native timer handling using wc counter
ALSA: ctxfi - Add missing inclusion of linux/math64.h
ALSA: ctxfi - Set device 0 for mixer control elements
ALSA: ctxfi - Clean up / optimize
ALSA: ctxfi - Set periods_min to 2
ALSA: ctxfi - Use native timer interrupt on emu20k1
ALSA: ctxfi - Fix previous fix for 64bit DMA
ALSA: ctxfi - Fix endian-dependent codes
ALSA: ctxfi - Allow 64bit DMA
...
|
|
* topic/ca0106:
ALSA: ca0106 - Fix master volume scale
ALSA: ca0106 - Add missing card->mixername field setup
ALSA: ca0106 - Add missing registrations of vmaster controls
|
|
* topic/au88x0:
ALSA: au88x0: fix wrong period_elapsed() call
ALSA: au88x0: fix .pointer callback
|
|
Currently the PCM resources are allocated only once and ever in prepare
callback, assuming that the PCM parameters are never changed. But it's
not true.
This patch adds the call of atc->pcm_release_resources() at hw_params
and hw_free callbacks to assure that the PCM setup is done correctly
for each h/w parameter changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The SRC instances may not exist when PCM pointer callback is called at
the state before initialization is finished. Add the NULL check just
to be sure.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added use_system_timer module option to force to use the system timer
instead of emu20k1 timer irq for debugging.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
CTUAA should be checked instead of CTHENDRIX. The latter is for 20k2 chip.
Also, fixed the detection of UAA/HENDRIX models by fixing the mask bits.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Clean up probe routines and model detection routines so that the driver
won't call and check the PCI subsystem id at each time.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- Fix a typo in the patch
- Adapted to follow the recent change for unsol event handling
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added 7.1 support for MSI GX620 and jack quirk.
Reference: kernel bug#13430
http://bugzilla.kernel.org/show_bug.cgi?id=13430
Signed-off-by: David Heidelberger <d.okias@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
EFX playback stream should have periods_min = 2 to avoid the buffer
position overflow (due to restrictions of the pcm-indirect helper).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- Clean up Hungarian coding style
- Don't use static variables for I2C information; this unables to use
multiple instances. Now they are stored in struct hw20k2 fields.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix possible buffer pointer overruns. Back to zero when it's equal
or over the buffer size.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove useless variable initializations and cast at the beginning of
functions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Allow 64bit DMA mask for emu20k2 chip, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Change the volume control to dB scale (as the raw data seems so).
Also added the TLV dB-scale information.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The master volume dB scale was wrongly defined as 0.50dB setp while
it must be 0.25dB step.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Optimize the timer update routine to look up wall clock once instead of
checking the position of each stream at each timer update.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace the house-made div64_32() with the standard div_u64*() functions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Mixer control elements are usually assigned to device 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- Use static tables instead of assigining each funciton pointer
- Add __devinit* to appropriate places; pcm, mixer and timer cannot be
marked because they are kept in the function table that lives long
- Move create_alsa_devs function out of struct ct_atc to mark it
__devinit
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Set 2 to minimal periods of playback pcm setups, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
emu20k1 has a native timer interrupt based on the audio clock, which
is more accurate than the system timer (from the synchronization POV).
This patch adds the code to handle this with multiple streams.
The system timer is still used on emu20k2, and can be used also for
emu20k1 easily by changing USE_SYSTEM_TIMER to 1 in cttimer.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove unneeded substitution to 32bit int to make it really working.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
with BIOS probing only we offer a non functional headphone swith and
volume slider.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The UAA-mode check in hwct20k1.c is implemented with the endian-dependent
codes. Fix to be more portable (and readable).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
emu20kx chips support 64bit address PTE. Allow the DMA bit mask to
accept 64bit address, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix this build error when CONFIG_PM is not set:
ound/pci/hda/hda_intel.c: In function 'azx_bus_reset':
sound/pci/hda/hda_intel.c:1270: error: implicit declaration of function 'snd_pcm_suspend_all'
sound/pci/hda/hda_intel.c:1271: error: implicit declaration of function 'snd_hda_suspend'
sound/pci/hda/hda_intel.c:1272: error: implicit declaration of function 'snd_hda_resume'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Enable all three capture channels, including the missing nid 7 which is
the only one capable of capturing DMIC input
Enable Headphone amp for the HP jack. This causes a volume boost for
headphones, but does not cause any noticeable effect for light loads
like other amps, so there is no need to make it configurable.
Add Input Mix capture mux setting to capture the output of the playback
input mux (that is, what goes out the speakers except for PCM)
Hack another coef register because the stereo DMIC for some reason
produces a nonstandard sum/difference signal. I found a bit to make it
just use the sum signal for both channels, which makes it behave like a
standard mono microphone. The stereo is useless anyway (they're 1cm apart).
Tested working: Three capture channels, mic in, line in, DMIC.
Tested not working: CD. Not sure why, might be unconnected in the actual
hardware or a CD drive issue.
Also looked at SPDIF. It appears to work (emitter lights up inside the
HP out jack) but I lack a proper miniTOSLINK cable to test it.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
Use SG-buffers instead of contiguous pages.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove the limitation of PAGE_SIZE to be 4k by defining the own
page size and macros for 4k. 8kb page size could be natively supported,
but it's disabled right now for simplicity.
Also, clean up using upper_32_bits() macro.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The device seems supporting only U8, S16, S24_3LE, S32. Other linear
formats result in bad outputs.
Also, added the support for 32bit float format, which wasn't listed
in the original code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
PCM names for surround streams should be also fixed as well as the mixer
element names. Also, a bit clean up for PCM name setup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We usually pick up "Surround" mixer for the rear output, and "Side"
for the extra surround. Fix the channel mapping to follow it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The prepare callback can be called multiple times, thus it needs to
release and acquire the resource again by itself at the second or later
call.
Simply add pcm_release_resources() at the beginning of each prepare
callback in ctatc.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
Although the vmaster controls are created, they aren't registered thus
they don't appear in the real world. Added the missing snd_ctl_add()
calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
|
|
Short story: this laptop has 5.1 built-in speakers which you *really*
want to use (the not-so-"sub" woofer is what makes the audio above
average for a laptop), so 6-channel support is important (plus a decent
asound.conf to upmix stereo). It also has the 3 typical jacks that ought
to have a selectable mode. And it's based on ALC889, which sucks.
Rationale/explanations:
The const_channel_count stuff was added because, for a laptop like this,
you always have 6 channels available (internal speakers) but still need
to set the mode for the 3 external jacks. Therefore, the device always
needs to be in 6-channel mode but there still needs to be a mixer
control for the jack mode. You could use line/mic-in at the same time as
the 6 internal speakers, for example. You might be tempted to make it
even smarter by dynamically switching the max channel count when
headphones are plugged in (therefore muting the internal speakers and
reducing the physical channel count to the jack channel mode), but as a
user I consider this to be harmful because I want the audio to blow up
to 6 channels / upmixed as soon as I unplug the headphones, and having
opened the device while in 2-channel mode would prevent this from
working (and always making 6-channel mode available doesn't do any harm).
The hardware needs EAPD turned on and the DACs routed to the internal
speaker pins, so the patch adds those verbs.
The ALC889 CLFE and subsequent (side/aux, here unused) DACs do NOT work
by default, at least here. I wasted much time trying to talk to
Realtek/pshou about this, but they just kept sending me useless updates
to patch_realtek.c that did nothing relevant. In the end I gave up and
brute forced the issue by trying to flip every bit in the proprietary
coefficient registers, and eventually found the two magic registers that
need to be cleared to enable all DACs. I have only heard Acer users
complain, but that might be because ALC889 is pretty new and using 5.1
(and noticing the missing center/lfe channels) might not be that common.
If this is a generalized issue with all ALC889 systems then those verbs
should probably be moved to a common verb array.
The internal mic is untested and probably doesn't work.
These settings will probably work for other Acer Gemstone laptops with
the same 5.1 speaker config. When identified, those should be added to
the PCI subsystem ID list.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A space has to be put between GPL and v2.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace a spinlock with a mutex protecting the vm block list at
mmap / munmap calls, which caused Oops like below:
BUG: sleeping function called from invalid context at mm/slub.c:1599
in_atomic(): 0, irqs_disabled(): 1, pid: 32065, name: xine
Pid: 32065, comm: xine Tainted: P 2.6.29.4-75.fc10.x86_64 #1
Call Trace:
[<ffffffff81040685>] __might_sleep+0x105/0x10a
[<ffffffff810c9fae>] kmem_cache_alloc+0x32/0xe2
[<ffffffffa08e3110>] ct_vm_map+0xfa/0x19e [snd_ctxfi]
[<ffffffffa08e1a07>] ct_map_audio_buffer+0x4c/0x76 [snd_ctxfi]
[<ffffffffa08e2aa5>] atc_pcm_playback_prepare+0x1d7/0x2a8 [snd_ctxfi]
[<ffffffff8105ef3f>] ? up_read+0x9/0xb
[<ffffffff81186b61>] ? __up_read+0x7c/0x87
[<ffffffffa08e36a6>] ct_pcm_playback_prepare+0x39/0x60 [snd_ctxfi]
[<ffffffffa0886bcb>] snd_pcm_do_prepare+0x16/0x28 [snd_pcm]
[<ffffffffa08867c7>] snd_pcm_action_single+0x2d/0x5b [snd_pcm]
[<ffffffffa08881f3>] snd_pcm_action_nonatomic+0x52/0x6a [snd_pcm]
[<ffffffffa088a723>] snd_pcm_common_ioctl1+0x404/0xc79 [snd_pcm]
[<ffffffff810c52c8>] ? alloc_pages_current+0xb9/0xc2
[<ffffffff810c9402>] ? new_slab+0x1a5/0x1cb
[<ffffffff810ab9ea>] ? vma_prio_tree_insert+0x23/0xc1
[<ffffffffa088b411>] snd_pcm_playback_ioctl1+0x213/0x230 [snd_pcm]
[<ffffffff810b6c20>] ? mmap_region+0x397/0x4c9
[<ffffffffa088bd9b>] snd_pcm_playback_ioctl+0x2e/0x36 [snd_pcm]
[<ffffffff810ddc64>] vfs_ioctl+0x2a/0x78
[<ffffffff810de130>] do_vfs_ioctl+0x462/0x4a2
[<ffffffff81029cef>] ? default_spin_lock_flags+0x9/0xe
[<ffffffff81374647>] ? trace_hardirqs_off_thunk+0x3a/0x6c
[<ffffffff810de1c5>] sys_ioctl+0x55/0x77
[<ffffffff8101133a>] system_call_fastpath+0x16/0x1b
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The reset of a BUS controller during operations is somehow risky and
shouldn't be done inevitably for devices that have apparently no such
codec-communication problems.
This patch adds the check of the hardware and limits the bus-reset
capability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some machines machine cause a severe CORB/RIRB stall in certain
weird conditions, such as PA access at the start up together with
fglrx driver. This seems unable to be recovered without the controller
reset.
This patch allows the bus controller reset at critical errors so
that the communication gets recovered again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|