| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch adds a basic nl802154 framework. Most of this code was
grabbed from nl80211 framework.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch removes the FSF address in files which belongs to ieee802154
and mac802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch fixed the coding style issues reported by checkpatch.pl
following issues fixed:
CHECK: Alignment should match open parenthesis
WARNING: line over 80 characters
CHECK: Blank lines aren't necessary before a close brace '}'
WARNING: networking block comments don't use an empty /* line, use /* Comment...
WARNING: Missing a blank line after declarations
WARNING: networking block comments start with * on subsequent lines
CHECK: braces {} should be used on all arms of this statement
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Tested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds user-visible interfaces for the llsec infrastructure.
For the added methods, the only major difference between all add/remove
implementation lies in how the specific object is parsed, and for dump
requests, how objects are written into netlink messages.
To save on boilerplate code, table dumps are routed through a helper
function that handles netlink dump state, leaving the actual dumping
code to care only about iterating over the table to be dumped and
filling netlink messages. For add/remove methods, the boilerplate
required to work is not quite as large, but still enough to also move
into a local helper.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 9b2777d6089bcd (ieee802154: add TX power control to wpan_phy)
and following erroneously added CSMA and CCA parameters for 802.15.4
devices as PHY parameters, while they are actually MAC parameters and
can differ for any two WPAN instances. Since it is now sensible to have
multiple WPAN devices with differing CSMA/CCA parameters, make these
parameters MAC parameters instead.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the current u8 transmit_power in wpan_phy with s8 transmit_power.
The u8 field contained the actual tx power and a tolerance field,
which no physical radio every used. Adjust sysfs entries to keep
compatibility with userspace, give tolerances of +-1dB statically there.
This patch only adds support for this in the at86rf230 driver and the
RF212 chip. Configuration calculation for RF212 is also somewhat basic,
but does the job - the RF212 datasheet gives a large table with
suggested values for combinations of TX power and page/channel, if this
does not work well, we might have to copy the whole table.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register generic netlink multicast groups as an array with
the family and give them contiguous group IDs. Then instead
of passing the global group ID to the various functions that
send messages, pass the ID relative to the family - for most
families that's just 0 because the only have one group.
This avoids the list_head and ID in each group, adding a new
field for the mcast group ID offset to the family.
At the same time, this allows us to prevent abusing groups
again like the quota and dropmon code did, since we can now
check that a family only uses a group it owns.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This simplifies the code since there's no longer a need to
have error handling in the registration.
Unfortunately it means more extern function declarations are
needed, but the overall goal would seem to justify this.
While at it, also fix the registration error path - if the
family registration failed then it shouldn't be unregistered.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two nl802154 helpers: one for starting a reply message, one for sending.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
|
|
Move all mac-related stuff to separate file so that ieee802154/netlink.c
contains only generic code.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
|
