| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
For IPv4, default route is learned via DHCPv4 and user is allowed to change
metric using config etc/network/interfaces. But for IPv6, default route can
be learned via RA, for which, currently a fixed metric value 1024 is used.
Ideally, user should be able to configure metric on default route for IPv6
similar to IPv4. This patch adds sysctl for the same.
Logs:
For IPv4:
Config in etc/network/interfaces:
auto eth0
iface eth0 inet dhcp
metric 4261413864
IPv4 Kernel Route Table:
$ ip route list
default via 172.21.47.1 dev eth0 metric 4261413864
FRR Table, if a static route is configured:
[In real scenario, it is useful to prefer BGP learned default route over DHCPv4 default route.]
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, P - PIM, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
> - selected route, * - FIB route
S>* 0.0.0.0/0 [20/0] is directly connected, eth0, 00:00:03
K 0.0.0.0/0 [254/1000] via 172.21.47.1, eth0, 6d08h51m
i.e. User can prefer Default Router learned via Routing Protocol in IPv4.
Similar behavior is not possible for IPv6, without this fix.
After fix [for IPv6]:
sudo sysctl -w net.ipv6.conf.eth0.net.ipv6.conf.eth0.ra_defrtr_metric=1996489705
IP monitor: [When IPv6 RA is received]
default via fe80::xx16:xxxx:feb3:ce8e dev eth0 proto ra metric 1996489705 pref high
Kernel IPv6 routing table
$ ip -6 route list
default via fe80::be16:65ff:feb3:ce8e dev eth0 proto ra metric 1996489705 expires 21sec hoplimit 64 pref high
FRR Table, if a static route is configured:
[In real scenario, it is useful to prefer BGP learned default route over IPv6 RA default route.]
Codes: K - kernel route, C - connected, S - static, R - RIPng,
O - OSPFv3, I - IS-IS, B - BGP, N - NHRP, T - Table,
v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
> - selected route, * - FIB route
S>* ::/0 [20/0] is directly connected, eth0, 00:00:06
K ::/0 [119/1001] via fe80::xx16:xxxx:feb3:ce8e, eth0, 6d07h43m
If the metric is changed later, the effect will be seen only when next IPv6
RA is received, because the default route must be fully controlled by RA msg.
Below metric is changed from 1996489705 to 1996489704.
$ sudo sysctl -w net.ipv6.conf.eth0.ra_defrtr_metric=1996489704
net.ipv6.conf.eth0.ra_defrtr_metric = 1996489704
IP monitor:
[On next IPv6 RA msg, Kernel deletes prev route and installs new route with updated metric]
Deleted default via fe80::xx16:xxxx:feb3:ce8e dev eth0 proto ra metric 1996489705 expires 3sec hoplimit 64 pref high
default via fe80::xx16:xxxx:feb3:ce8e dev eth0 proto ra metric 1996489704 pref high
Signed-off-by: Praveen Chaudhary <pchaudhary@linkedin.com>
Signed-off-by: Zhenggen Xu <zxu@linkedin.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210125214430.24079-1-pchaudhary@linkedin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
and include <linux/const.h> in UAPI headers instead of <linux/kernel.h>.
The reason is to avoid indirect <linux/sysinfo.h> include when using
some network headers: <linux/netlink.h> or others -> <linux/kernel.h>
-> <linux/sysinfo.h>.
This indirect include causes on MUSL redefinition of struct sysinfo when
included both <sys/sysinfo.h> and some of UAPI headers:
In file included from x86_64-buildroot-linux-musl/sysroot/usr/include/linux/kernel.h:5,
from x86_64-buildroot-linux-musl/sysroot/usr/include/linux/netlink.h:5,
from ../include/tst_netlink.h:14,
from tst_crypto.c:13:
x86_64-buildroot-linux-musl/sysroot/usr/include/linux/sysinfo.h:8:8: error: redefinition of `struct sysinfo'
struct sysinfo {
^~~~~~~
In file included from ../include/tst_safe_macros.h:15,
from ../include/tst_test.h:93,
from tst_crypto.c:11:
x86_64-buildroot-linux-musl/sysroot/usr/include/sys/sysinfo.h:10:8: note: originally defined here
Link: https://lkml.kernel.org/r/20201015190013.8901-1-petr.vorel@gmail.com
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Suggested-by: Rich Felker <dalias@aerifal.cx>
Acked-by: Rich Felker <dalias@libc.org>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As zone reclaim has been replaced by node reclaim, this patch fixes
related comments.
Link: http://lkml.kernel.org/r/20191126141346.GA22665@haolee.github.io
Signed-off-by: Hao Lee <haolee.swjtu@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
So that we can also runtime chose to print out the needed system info
for panic, other than setting the kernel cmdline.
Link: http://lkml.kernel.org/r/1543398842-19295-3-git-send-email-feng.tang@intel.com
Signed-off-by: Feng Tang <feng.tang@intel.com>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Preventing the kernel from responding to ICMP Echo Requests messages
can be useful in several ways. The sysctl parameter
'icmp_echo_ignore_all' can be used to prevent the kernel from
responding to IPv4 ICMP echo requests. For IPv6 pings, such
a sysctl kernel parameter did not exist.
Add the ability to prevent the kernel from responding to IPv6
ICMP echo requests through the use of the following sysctl
parameter : /proc/sys/net/ipv6/icmp/echo_ignore_all.
Update the documentation to reflect this change.
Signed-off-by: Virgile Jarry <virgile@acceis.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were some documentation locations that irda was mentioned, as well
as an old MAINTAINERS entry and the networking sysctl entries. Clean
these all out as this stuff really is finally gone.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
license
Many user space API headers are missing licensing information, which
makes it hard for compliance tools to determine the correct license.
By default are files without license information under the default
license of the kernel, which is GPLV2. Marking them GPLV2 would exclude
them from being included in non GPLV2 code, which is obviously not
intended. The user space API headers fall under the syscall exception
which is in the kernels COPYING file:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
otherwise syscall usage would not be possible.
Update the files which contain no license information with an SPDX
license identifier. The chosen identifier is 'GPL-2.0 WITH
Linux-syscall-note' which is the officially assigned identifier for the
Linux syscall exception. SPDX license identifiers are a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We are not supposed to add new entries to this thing
any more.
Thanks to Eric Dumazet for noticing this.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Constants used for tuning are generally a bad idea, especially as hardware
changes over time. Replace the constant 2 jiffies with sysctl variable
netdev_budget_usecs to enable sysadmins to tune the softirq processing.
Also document the variable.
For example, a very fast machine might tune this to 1000 microseconds,
while my regression testing 486DX-25 needs it to be 4000 microseconds on
a nearly idle network to prevent time_squeeze from being incremented.
Version 2: changed jiffies to microseconds for predictable units.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds a new sysctl accept_ra_rt_info_min_plen that
defines the minimum acceptable prefix length of Route Information
Options. The new sysctl is intended to be used together with
accept_ra_rt_info_max_plen to configure a range of acceptable
prefix lengths. It is useful to prevent misconfigurations from
unintentionally blackholing too much of the IPv6 address space
(e.g., home routers announcing RIOs for fc00::/7, which is
incorrect).
Signed-off-by: Joel Scherpelz <jscherpelz@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't user forward declarations of internal kernel structures in headers
exported to userspace.
Move "struct completion;".
Move "struct task_struct;".
Link: http://lkml.kernel.org/r/20160713215808.GA22486@p183.telecom.by
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There have been several times where I have had to rebuild a kernel to
cause a panic when hitting a WARN() in the code in order to get a crash
dump from a system. Sometimes this is easy to do, other times (such as
in the case of a remote admin) it is not trivial to send new images to
the user.
A much easier method would be a switch to change the WARN() over to a
panic. This makes debugging easier in that I can now test the actual
image the WARN() was seen on and I do not have to engage in remote
debugging.
This patch adds a panic_on_warn kernel parameter and
/proc/sys/kernel/panic_on_warn calls panic() in the
warn_slowpath_common() path. The function will still print out the
location of the warning.
An example of the panic_on_warn output:
The first line below is from the WARN_ON() to output the WARN_ON()'s
location. After that the panic() output is displayed.
WARNING: CPU: 30 PID: 11698 at /home/prarit/dummy_module/dummy-module.c:25 init_dummy+0x1f/0x30 [dummy_module]()
Kernel panic - not syncing: panic_on_warn set ...
CPU: 30 PID: 11698 Comm: insmod Tainted: G W OE 3.17.0+ #57
Hardware name: Intel Corporation S2600CP/S2600CP, BIOS RMLSDP.86I.00.29.D696.1311111329 11/11/2013
0000000000000000 000000008e3f87df ffff88080f093c38 ffffffff81665190
0000000000000000 ffffffff818aea3d ffff88080f093cb8 ffffffff8165e2ec
ffffffff00000008 ffff88080f093cc8 ffff88080f093c68 000000008e3f87df
Call Trace:
[<ffffffff81665190>] dump_stack+0x46/0x58
[<ffffffff8165e2ec>] panic+0xd0/0x204
[<ffffffffa038e05f>] ? init_dummy+0x1f/0x30 [dummy_module]
[<ffffffff81076b90>] warn_slowpath_common+0xd0/0xd0
[<ffffffffa038e040>] ? dummy_greetings+0x40/0x40 [dummy_module]
[<ffffffff81076c8a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa038e05f>] init_dummy+0x1f/0x30 [dummy_module]
[<ffffffff81002144>] do_one_initcall+0xd4/0x210
[<ffffffff811b52c2>] ? __vunmap+0xc2/0x110
[<ffffffff810f8889>] load_module+0x16a9/0x1b30
[<ffffffff810f3d30>] ? store_uevent+0x70/0x70
[<ffffffff810f49b9>] ? copy_module_from_fd.isra.44+0x129/0x180
[<ffffffff810f8ec6>] SyS_finit_module+0xa6/0xd0
[<ffffffff8166cf29>] system_call_fastpath+0x12/0x17
Successfully tested by me.
hpa said: There is another very valid use for this: many operators would
rather a machine shuts down than being potentially compromised either
functionally or security-wise.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This can be used in virtual networking applications, and
may have other uses as well. The option is disabled by
default.
A specific use case is setting up virtual routers, bridges, and
hosts on a single OS without the use of network namespaces or
virtual machines. With proper use of ip rules, routing tables,
veth interface pairs and/or other virtual interfaces,
and applications that can bind to interfaces and/or IP addresses,
it is possibly to create one or more virtual routers with multiple
hosts attached. The host interfaces can act as IPv6 systems,
with radvd running on the ports in the virtual routers. With the
option provided in this patch enabled, those hosts can now properly
obtain IPv6 addresses from the radvd.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
|
