| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The switchdev value for the SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME
attribute is a clock_t and requires to use helpers such as
clock_t_to_jiffies() to convert to milliseconds.
Change ageing_time type from u32 to clock_t to make it explicit.
Fixes: f55ac58ae64c ("switchdev: add bridge ageing_time attribute")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This flag indicates whether fragmentation of segments is allowed.
Formerly this policy was hardcoded according to IPSKB_FORWARDED (set by
either ip_forward or ipmr_forward).
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Bluetooth controllers allow for reading hardware and firmware
related vendor specific infos. If they are available, then they can be
exposed via debugfs now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The protoypes for hci_recv_frame and hci_recv_diag are in the wrong
location in the header file. Move them close to all the other hci_dev
related exported functions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
This helper serves to know if two switchdev port netdevices belong to the
same HW ASIC, e.g to figure out if forwarding offload is possible between them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Identifying address family operations during rx path is not something
expensive but it's ugly to the eye to have it done multiple times,
specially when we already validated it during initial rx processing.
This patch takes advantage of the now shared sctp_input_cb and make the
pointer to the operations readily available.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCTP will try to access original IP headers on sctp_recvmsg in order to
copy the addresses used. There are also other places that do similar access
to IP or even SCTP headers. But after 90017accff61 ("sctp: Add GSO
support") they aren't always there because they are only present in the
header skb.
SCTP handles the queueing of incoming data by cloning the incoming skb
and limiting to only the relevant payload. This clone has its cb updated
to something different and it's then queued on socket rx queue. Thus we
need to fix this in two moments.
For rx path, not related to socket queue yet, this patch uses a
partially copied sctp_input_cb to such GSO frags. This restores the
ability to access the headers for this part of the code.
Regarding the socket rx queue, it removes iif member from sctp_event and
also add a chunk pointer on it.
With these changes we're always able to reach the headers again.
The biggest change here is that now the sctp_chunk struct and the
original skb are only freed after the application consumed the buffer.
Note however that the original payload was already like this due to the
skb cloning.
For iif, SCTP's IPv4 code doesn't use it, so no change is necessary.
IPv6 now can fetch it directly from original's IPv6 CB as the original
skb is still accessible.
In the future we probably can simplify sctp_v*_skb_iif() stuff, as
sctp_v4_skb_iif() was called but it's return value not used, and now
it's not even called, but such cleanup is out of scope for this change.
Fixes: 90017accff61 ("sctp: Add GSO support")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch needs 8 bytes in there. sctp_ulpevent has a hole due to
bad alignment; msg_flags is using 4 bytes while it actually uses only 2, so
we shrink it, and iif member (4 bytes) which can be easily fetched from
another place once the next patch is there, so we remove it and thus
creating space for 8 bytes.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We process input path in other files too and having access to it is
nice, so move it to a header where it's shared.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-07-13
Here's our main bluetooth-next pull request for the 4.8 kernel:
- Fixes and cleanups in 802.15.4 and 6LoWPAN code
- Fix out of bounds issue in btmrvl driver
- Fixes to Bluetooth socket recvmsg return values
- Use crypto_cipher_encrypt_one() instead of crypto_skcipher
- Cleanup of Bluetooth connection sysfs interface
- New Authentication failure reson code for Disconnected mgmt event
- New USB IDs for Atheros, Qualcomm and Intel Bluetooth controllers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dccp verifies packet integrity, including length, at initial rcv in
dccp_invalid_packet, later pulls headers in dccp_enqueue_skb.
A call to sk_filter in-between can cause __skb_pull to wrap skb->len.
skb_copy_datagram_msg interprets this as a negative value, so
(correctly) fails with EFAULT. The negative length is reported in
ioctl SIOCINQ or possibly in a DCCP_WARN in dccp_close.
Introduce an sk_receive_skb variant that caps how small a filter
program can trim packets, and call this in dccp with the header
length. Excessively trimmed packets are now processed normally and
queued for reception as 0B payloads.
Fixes: 7c657876b63c ("[DCCP]: Initial implementation")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If link is disconnected due to Authentication Failure (PIN or Key
Missing status) userspace will be notified about this with proper error
code. Many LE profiles define "PIN or Key Missing" status as indication
of remote lost bond so this allows userspace to take action on this.
@ Device Connected: 88:63:DF:88:0E:83 (1) flags 0x0000
02 01 1a 05 03 0a 18 0d 18 0b 09 48 65 61 72 74 ...........Heart
20 52 61 74 65 Rate
> HCI Event: Command Status (0x0f) plen 4
LE Read Remote Used Features (0x08|0x0016) ncmd 1
Status: Success (0x00)
> ACL Data RX: Handle 3585 flags 0x02 dlen 11
ATT: Read By Group Type Request (0x10) len 6
Handle range: 0x0001-0xffff
Attribute group type: Primary Service (0x2800)
> HCI Event: LE Meta Event (0x3e) plen 12
LE Read Remote Used Features (0x04)
Status: Success (0x00)
Handle: 3585
Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00
LE Encryption
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28
Handle: 3585
Random number: 0x0000000000000000
Encrypted diversifier: 0x0000
Long term key: 26201cd479a0921b6f949f0b1fa8dc82
> HCI Event: Command Status (0x0f) plen 4
LE Start Encryption (0x08|0x0019) ncmd 1
Status: Success (0x00)
> HCI Event: Encryption Change (0x08) plen 4
Status: PIN or Key Missing (0x06)
Handle: 3585
Encryption: Disabled (0x00)
< HCI Command: Disconnect (0x01|0x0006) plen 3
Handle: 3585
Reason: Authentication Failure (0x05)
> HCI Event: Command Status (0x0f) plen 4
Disconnect (0x01|0x0006) ncmd 1
Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4
Status: Success (0x00)
Handle: 3585
Reason: Connection Terminated By Local Host (0x16)
@ Device Disconnected: 88:63:DF:88:0E:83 (1) reason 4
@ Device Connected: C4:43:8F:A3:4D:83 (0) flags 0x0000
08 09 4e 65 78 75 73 20 35 ..Nexus 5
> HCI Event: Command Status (0x0f) plen 4
Authentication Requested (0x01|0x0011) ncmd 1
Status: Success (0x00)
> HCI Event: Link Key Request (0x17) plen 6
Address: C4:43:8F:A3:4D:83 (LG Electronics)
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
Address: C4:43:8F:A3:4D:83 (LG Electronics)
Link key: 080812e4aa97a863d11826f71f65a933
> HCI Event: Command Complete (0x0e) plen 10
Link Key Request Reply (0x01|0x000b) ncmd 1
Status: Success (0x00)
Address: C4:43:8F:A3:4D:83 (LG Electronics)
> HCI Event: Auth Complete (0x06) plen 3
Status: PIN or Key Missing (0x06)
Handle: 75
@ Authentication Failed: C4:43:8F:A3:4D:83 (0) status 0x05
< HCI Command: Disconnect (0x01|0x0006) plen 3
Handle: 75
Reason: Remote User Terminated Connection (0x13)
> HCI Event: Command Status (0x0f) plen 4
Disconnect (0x01|0x0006) ncmd 1
Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4
Status: Success (0x00)
Handle: 75
Reason: Connection Terminated By Local Host (0x16)
@ Device Disconnected: C4:43:8F:A3:4D:83 (0) reason 4
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree.
they are:
1) Fix leak in the error path of nft_expr_init(), from Liping Zhang.
2) Tracing from nf_tables cannot be disabled, also from Zhang.
3) Fix an integer overflow on 32bit archs when setting the number of
hashtable buckets, from Florian Westphal.
4) Fix configuration of ipvs sync in backup mode with IPv6 address,
from Quentin Armitage via Simon Horman.
5) Fix incorrect timeout calculation in nft_ct NFT_CT_EXPIRATION,
from Florian Westphal.
6) Skip clash resolution in conntrack insertion races if NAT is in
place.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
prsctp PRIO policy is a policy to abandon lower priority chunks when
asoc doesn't have enough snd buffer, so that the current chunk with
higher priority can be queued successfully.
Similar to TTL/RTX policy, we will set the priority of the chunk to
prsctp_param with sinfo->sinfo_timetolive in sctp_set_prsctp_policy().
So if PRIO policy is enabled, msg->expire_at won't work.
asoc->sent_cnt_removable will record how many chunks can be checked to
remove. If priority policy is enabled, when the chunk is queued into
the out_queue, we will increase sent_cnt_removable. When the chunk is
moved to abandon_queue or dequeue and free, we will decrease
sent_cnt_removable.
In sctp_sendmsg, we will check if there is enough snd buffer for current
msg and if sent_cnt_removable is not 0. Then try to abandon chunks in
sctp_prune_prsctp when sendmsg from the retransmit/transmited queue, and
free chunks from out_queue in right order until the abandon+free size >
msg_len - sctp_wfree. For the abandon size, we have to wait until it
sends FORWARD TSN, receives the sack and the chunks are really freed.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
prsctp TTL policy is a policy to abandon chunks when they expire
at the specific time in local stack. It's similar with expires_at
in struct sctp_datamsg.
This patch uses sinfo->sinfo_timetolive to set the specific time for
TTL policy. sinfo->sinfo_timetolive is also used for msg->expires_at.
So if prsctp_enable or TTL policy is not enabled, msg->expires_at
still works as before.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds SCTP_PR_ASSOC_STATUS to sctp sockopt, which is used
to dump the prsctp statistics info from the asoc. The prsctp statistics
includes abandoned_sent/unsent from the asoc. abandoned_sent is the
count of the packets we drop packets from retransmit/transmited queue,
and abandoned_unsent is the count of the packets we drop from out_queue
according to the policy.
Note: another option for prsctp statistics dump described in rfc is
SCTP_PR_STREAM_STATUS, which is used to dump the prsctp statistics
info from each stream. But by now, linux doesn't yet have per stream
statistics info, it needs rfc6525 to be implemented. As the prsctp
statistics for each stream has to be based on per stream statistics,
we will delay it until rfc6525 is done in linux.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to section 4.5 of rfc7496, prsctp_enable should be per asoc.
We will add prsctp_enable to both asoc and ep, and replace the places
where it used net.sctp->prsctp_enable with asoc->prsctp_enable.
ep->prsctp_enable will be initialized with net.sctp->prsctp_enable, and
asoc->prsctp_enable will be initialized with ep->prsctp_enable. We can
also modify it's value through sockopt SCTP_PR_SUPPORTED.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can pass the netns pointer as parameter to the functions that need to
gain access to it. From basechains, I didn't find any client for this
field anymore so let's remove this too.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
It did use a fixed-size bucket list plus single lock to protect add/del.
Unlike the main conntrack table we only need to add and remove keys.
Convert it to rhashtable to get table autosizing and per-bucket locking.
The maximum number of entries is -- as before -- tied to the number of
conntracks so we do not need another upperlimit.
The change does not handle rhashtable_remove_fast error, only possible
"error" is -ENOENT, and that is something that can happen legitimetely,
e.g. because nat module was inserted at a later time and no src manip
took place yet.
Tested with http-client-benchmark + httpterm with DNAT and SNAT rules
in place.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The nat extension structure is 32bytes in size on x86_64:
struct nf_conn_nat {
struct hlist_node bysource; /* 0 16 */
struct nf_conn * ct; /* 16 8 */
union nf_conntrack_nat_help help; /* 24 4 */
int masq_index; /* 28 4 */
/* size: 32, cachelines: 1, members: 4 */
/* last cacheline: 32 bytes */
};
The hlist is needed to quickly check for possible tuple collisions
when installing a new nat binding. Storing this in the extension
area has two drawbacks:
1. We need ct backpointer to get the conntrack struct from the extension.
2. When reallocation of extension area occurs we need to fixup the bysource
hash head via hlist_replace_rcu.
We can avoid both by placing the hlist_head in nf_conn and place nf_conn in
the bysource hash rather than the extenstion.
We can also remove the ->move support; no other extension needs it.
Moving the entire nat extension into nf_conn would be possible as well but
then we have to add yet another callback for deletion from the bysource
hash table rather than just using nat extension ->destroy hook for this.
nf_conn size doesn't increase due to aligment, followup patch replaces
hlist_node with single pointer.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We don't need to acquire the bucket lock during early drop, we can
use lockless traveral just like ____nf_conntrack_find.
The timer deletion serves as synchronization point, if another cpu
attempts to evict same entry, only one will succeed with timer deletion.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When we do "cat /proc/net/nf_conntrack", and meanwhile resize the conntrack
hash table via /sys/module/nf_conntrack/parameters/hashsize, race will
happen, because reader can observe a newly allocated hash but the old size
(or vice versa). So oops will happen like follows：
BUG: unable to handle kernel NULL pointer dereference at 0000000000000017
IP: [<ffffffffa0418e21>] seq_print_acct+0x11/0x50 [nf_conntrack]
Call Trace:
[<ffffffffa0412f4e>] ? ct_seq_show+0x14e/0x340 [nf_conntrack]
[<ffffffff81261a1c>] seq_read+0x2cc/0x390
[<ffffffff812a8d62>] proc_reg_read+0x42/0x70
[<ffffffff8123bee7>] __vfs_read+0x37/0x130
[<ffffffff81347980>] ? security_file_permission+0xa0/0xc0
[<ffffffff8123cf75>] vfs_read+0x95/0x140
[<ffffffff8123e475>] SyS_read+0x55/0xc0
[<ffffffff817c2572>] entry_SYSCALL_64_fastpath+0x1a/0xa4
It is very easy to reproduce this kernel crash.
1. open one shell and input the following cmds:
while : ; do
echo $RANDOM > /sys/module/nf_conntrack/parameters/hashsize
done
2. open more shells and input the following cmds:
while : ; do
cat /proc/net/nf_conntrack
done
3. just wait a monent, oops will happen soon.
The solution in this patch is based on Florian's Commit 5e3c61f98175
("netfilter: conntrack: fix lookup race during hash resize"). And
add a wrapper function nf_conntrack_get_ht to get hash and hsize
suggested by Florian Westphal.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When sending an ATR_REQ, the initiator must wait for the ATR_RES at
least 'RWT(nfcdep,activation) + dRWT(nfcdep)' and no more than
'RWT(nfcdep,activation) + dRWT(nfcdep) + dT(nfcdep,initiator)'. This
gives a timeout value between 1237 ms and 1337 ms. This patch defines
DIGITAL_ATR_RES_RWT to 1337 used for the timeout value of ATR_REQ
command.
For other DEP PDUs, the initiator must wait between 'RWT + dRWT(nfcdep)'
and 'RWT + dRWT(nfcdep) + dT(nfcdep,initiator)' where RWT is given by
the following formula: '(256 * 16 / f(c)) * 2^wt' where wt is the value
of the TO field in the ATR_RES response and is in the range between 0
and 14. This patch declares a mapping table for wt values and gives RWT
max values between 100 ms and 5049 ms.
This patch also defines DIGITAL_ATR_RES_TO_WT, the maximum wt value in
target mode, to 8.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch fixes the way an I-PDU is saved in case it needs to be sent
again. It is now copied using pskb_copy() and not simply referenced
using skb_get() since it could be modified by the driver.
digital_in_send_saved_skb() and digital_tg_send_saved_skb() still get a
reference on the saved skb which is re-sent but release it if the send
operation fails. That way the caller doesn't have to take care about skb
ref in case of error.
RTOX supervisor PDU must not be saved as this can override a previously
saved I-PDU that should be re-sent later on.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The routing table of every switch in a tree is currently initialized to
all zeros. This is an issue since 0 is a valid port number.
Add a DSA_RTABLE_NONE=-1 constant to initialize the signed values of the
routing table pointing to other switches.
This fixes the device mapping of the mv88e6xxx driver where the port
pointing to the switch itself and to non-existent switches was wrongly
configured to be 0. It is now set to the expected 0xf value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to compute timeout.expires - jiffies, not the other way around.
Add a helper, another patch can then later change more places in
conntrack code where we currently open-code this.
Will allow us to only change one place later when we remove per-ct timer.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch cleanups the WARN_ON which occurs when the sk buffer has
insufficient buffer space by moving the WARN_ON into if condition.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch fixes ieee802154_get_fc_from_skb function on big endian
machines. The function get_unaligned_le16 converts the byte order to
host byte order but we want to keep the byte order like in mac header.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The RIOT-OS stack does send intra-pan frames but don't set the intra pan
flag inside the mac header. It seems this is valid frame addressing but
inefficient. Anyway this patch adds a new function for intra pan
addressing, doesn't matter if intra pan flag or source and destination
are the same. The newly introduction function will be used to check on
intra pan addressing for 6lowpan.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds ieee802154_skb_src_pan function to get the pointer
address of the source pan id at skb mac pointer.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds ieee802154_skb_dst_pan function to get the pointer
address of the destination pan id at skb mac pointer.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds netns support for 802.15.4 subsystem. Most parts are
copy&pasted from wireless subsystem, it has the identically userspace
API.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The PAD define should be above the experimental support. We don't care
about if we break userspace in experimental stuff but PAD is part of the
existing UAPI.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Stefan Schmidt<stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One more set of new features:
* beacon report (for radio measurement) support in cfg80211/mac80211
* hwsim: allow wmediumd in namespaces
* mac80211: extend 160MHz workaround to CSA IEs
* mesh: properly encrypt group-addressed privacy action frames
* mesh: allow setting peer AID
* first steps for MU-MIMO monitor mode
* along with various other cleanups and improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
into next
|
|
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next,
they are:
1) Don't use userspace datatypes in bridge netfilter code, from
Tobin Harding.
2) Iterate only once over the expectation table when removing the
helper module, instead of once per-netns, from Florian Westphal.
3) Extra sanitization in xt_hook_ops_alloc() to return error in case
we ever pass zero hooks, xt_hook_ops_alloc():
4) Handle NFPROTO_INET from the logging core infrastructure, from
Liping Zhang.
5) Autoload loggers when TRACE target is used from rules, this doesn't
change the behaviour in case the user already selected nfnetlink_log
as preferred way to print tracing logs, also from Liping Zhang.
6) Conntrack slabs with SLAB_HWCACHE_ALIGN to allow rearranging fields
by cache lines, increases the size of entries in 11% per entry.
From Florian Westphal.
7) Skip zone comparison if CONFIG_NF_CONNTRACK_ZONES=n, from Florian.
8) Remove useless defensive check in nf_logger_find_get() from Shivani
Bhardwaj.
9) Remove zone extension as place it in the conntrack object, this is
always include in the hashing and we expect more intensive use of
zones since containers are in place. Also from Florian Westphal.
10) Owner match now works from any namespace, from Eric Bierdeman.
11) Make sure we only reply with TCP reset to TCP traffic from
nf_reject_ipv4, patch from Liping Zhang.
12) Introduce --nflog-size to indicate amount of network packet bytes
that are copied to userspace via log message, from Vishwanath Pai.
This obsoletes --nflog-range that has never worked, it was designed
to achieve this but it has never worked.
13) Introduce generic macros for nf_tables object generation masks.
14) Use generation mask in table, chain and set objects in nf_tables.
This allows fixes interferences with ongoing preparation phase of
the commit protocol and object listings going on at the same time.
This update is introduced in three patches, one per object.
15) Check if the object is active in the next generation for element
deactivation in the rbtree implementation, given that deactivation
happens from the commit phase path we have to observe the future
status of the object.
16) Support for deletion of just added elements in the hash set type.
17) Allow to resize hashtable from /proc entry, not only from the
obscure /sys entry that maps to the module parameter, from Florian
Westphal.
18) Get rid of NFT_BASECHAIN_DISABLED, this code is not exercised
anymore since we tear down the ruleset whenever the netdevice
goes away.
19) Support for matching inverted set lookups, from Arturo Borrero.
20) Simplify the iptables_mangle_hook() by removing a superfluous
extra branch.
21) Introduce ether_addr_equal_masked() and use it from the netfilter
codebase, from Joe Perches.
22) Remove references to "Use netfilter MARK value as routing key"
from the Netfilter Kconfig description given that this toggle
doesn't exists already for 10 years, from Moritz Sichert.
23) Introduce generic NF_INVF() and use it from the xtables codebase,
from Joe Perches.
24) Setting logger to NONE via /proc was not working unless explicit
nul-termination was included in the string. This fixes seems to
leave the former behaviour there, so we don't break backward.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
adds mesh peer AID setting API.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
add API to support VHT MU-MIMO air sniffer.
in MU-MIMO there are parallel frames on the air while the HW
has only one RX.
add the capability to sniff one of the MU-MIMO parallel frames by
giving the sniffer additional information so it'll know which
of the parallel frames it shall follow.
Add attribute - NL80211_ATTR_MU_MIMO_GROUP_DATA - for getting
a MU-MIMO groupID in order to monitor packets from that group
using VHT MU-MIMO.
And add attribute -NL80211_ATTR_MU_MIMO_FOLLOW_ADDR - for passing
MAC address to monitor mode.
that option will be used by VHT MU-MIMO air sniffer to follow a
station according to it's MAC address using VHT MU-MIMO.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the data plane is offloaded the traffic doesn't go through the
networking stack. Therefore, after first resolving a neighbour the NUD
state machine will transition it from REACHABLE to STALE until it's
finally deleted by the garbage collector.
To prevent such situations the offloading driver should notify the NUD
state machine on any neighbours that were recently used. The driver's
polling interval should be set so that the NUD state machine can
function as if the traffic wasn't offloaded.
Currently, there are no in-tree drivers that can report confirmation for
a neighbour, but only 'used' indication. Therefore, the polling interval
should be set according to DELAY_FIRST_PROBE_TIME, as a neighbour will
transition from REACHABLE state to DELAY (instead of STALE) if "a packet
was sent within the last DELAY_FIRST_PROBE_TIME seconds" (RFC 4861).
Send a netevent whenever the DELAY_FIRST_PROBE_TIME changes - either via
netlink or sysctl - so that offloading drivers can correctly set their
polling interval.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extremely useful for setting packet type to host so i dont
have to modify the dst mac address using pedit (which requires
that i know the mac address)
Example usage:
tc filter add dev eth0 parent ffff: protocol ip pref 9 u32 \
match ip src 5.5.5.5/32 \
flowid 1:5 action skbedit ptype host
This will tag all packets incoming from 5.5.5.5 with type
PACKET_HOST
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This replaces the polling work struct with a delayed work struct and add
a 10 ms delay between 2 poll cycles. This avoids to flood the device
with 'switch off'/'switch on' commands.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
It used to be EXPORTed, but then EXPORT usage was cleaned up
(in 2012), without noticing that the function has no users at all
(and curiously, never had any users).
Delete it.
While at it, remove non-static "inline" hints on nearby functions:
these hints don't work across compilation units anyway,
and these functions are not used in their .c file, thus they are
never inlined. IOW: "inline" here does not help in any way.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Samuel Ortiz <sameo@linux.intel.com>
CC: Christophe Ricard <christophe.ricard@gmail.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add the commands to set and show the mode of SRIOV E-Switch, two modes
are supported:
* legacy: operating in the "old" L2 based mode (DMAC --> VF vport)
* switchdev: the E-Switch is referred to as whitebox switch configured
using standard tools such as tc, bridge, openvswitch etc. To allow
working with the tools, for each VF, a VF representor netdevice is
created by the E-Switch manager vendor device driver instance (e.g PF).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ether_addr_equal_64bits() requires some care about its arguments,
namely that 8 bytes might be read, even if last 2 byte values are not
used.
KASan detected a violation with null_mac_addr and lacpdu_mcast_addr
in bond_3ad.c
Same problem with mac_bcast[] and mac_v6_allmcast[] in bond_alb.c :
Although the 8-byte alignment was there, KASan would detect out
of bound accesses.
Fixes: 815117adaf5b ("bonding: use ether_addr_equal_unaligned for bond addr compare")
Fixes: bb54e58929f3 ("bonding: Verify RX LACPDU has proper dest mac-addr")
Fixes: 885a136c52a8 ("bonding: use compare_ether_addr_64bits() in ALB")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some arches have virtually mapped kernel stacks, or will soon have.
tcp_md5_hash_header() uses an automatic variable to copy tcp header
before mangling th->check and calling crypto function, which might
be problematic on such arches.
David says that using percpu storage is also problematic on non SMP
builds.
Just use kmalloc() to allocate scratch areas.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
