| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
SPI Multi I/O Bus Controller on RZ/G2L SoC is almost identical to
the RPC-IF interface found on R-Car Gen3 SoC's.
This patch adds a new compatible string for the RZ/G2L family so
that the timing values on RZ/G2L can be adjusted.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211025205631.21151-8-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
|
|
This patch fixes 2 problems:
[1] The output warning logs and data loss when performing
mount/umount then remount the device with jffs2 format.
[2] The access width of SMWDR[0:1]/SMRDR[0:1] register is wrong.
This is the sample warning logs when performing mount/umount then
remount the device with jffs2 format:
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x031c51d4:
Read 0x00034e00, calculated 0xadb272a7
The reason for issue [1] is that the writing data seems to
get messed up.
Data is only completed when the number of bytes is divisible by 4.
If you only have 3 bytes of data left to write, 1 garbage byte
is inserted after the end of the write stream.
If you only have 2 bytes of data left to write, 2 bytes of '00'
are added into the write stream.
If you only have 1 byte of data left to write, 2 bytes of '00'
are added into the write stream. 1 garbage byte is inserted after
the end of the write stream.
To solve problem [1], data must be written continuously in serial
and the write stream ends when data is out.
Following HW manual 62.2.15, access to SMWDR0 register should be
in the same size as the transfer size specified in the SPIDE[3:0]
bits in the manual mode enable setting register (SMENR).
Be sure to access from address 0.
So, in 16-bit transfer (SPIDE[3:0]=b'1100), SMWDR0 should be
accessed by 16-bit width.
Similar to SMWDR1, SMDDR0/1 registers.
In current code, SMWDR0 register is accessed by regmap_write()
that only set up to do 32-bit width.
To solve problem [2], data must be written 16-bit or 8-bit when
transferring 1-byte or 2-byte.
Fixes: ca7d8b980b67 ("memory: add Renesas RPC-IF driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Duc Nguyen <duc.nguyen.ub@renesas.com>
[wsa: refactored to use regmap only via reg_read/reg_write]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922091007.5516-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
|
|
Use spaces instead of tabs as word separator.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210601160608.312446-1-krzysztof.kozlowski@canonical.com
|
|
Define rpcif_enable_rpm() and rpcif_disable_rpm() as static
inline in the header instead of exporting them.
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Pavel Machek (CIP) <pavel@denx.de>
Link: https://lore.kernel.org/r/20201126191146.8753-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add the memory driver for Renesas RPC-IF which registers either SPI or
HyperFLash device depending on the contents of the device tree subnode.
It also provides the absract "back end" device APIs that can be used by
the "front end" SPI/MTD drivers to talk to the real hardware.
Based on the original patch by Mason Yang <masonccyang@mxic.com.tw>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/9a3606ec-d4d0-c63a-4fb6-631ab38e621c@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now that jedec_ddr_data.c was moved from lib/ to drivers/memory/,
<memory/jedec_ddr.h> is included only from drivers/memory/.
Make it a local header of drivers/memory/.
The directory include/memory is now gone.
While I am here, I also changed #include <linux/module.h> to
<linux/export.h>. Because CONFIG_DDR is bool, jedec_ddr_data.c is
never compiled as a module.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
add LPDDR2 data from the JEDEC spec JESD209-2. The data
includes:
1. Addressing information for LPDDR2 memories of different
densities and types(S2/S4)
2. AC timing data.
This data will useful for memory controller device drivers.
Right now this is used by the TI EMIF SDRAM controller
driver.
Signed-off-by: Aneesh V <aneesh@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
