| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 0d9cfc9b8cb17dbc29a98792d36ec39a1cf1395f upstream.
The Gemalto Cinterion PLS83-W modem (cdc_ether) is emitting confusing link
up and down events when the WWAN interface is activated on the modem-side.
Interrupt URBs will in consecutive polls grab:
* Link Connected
* Link Disconnected
* Link Connected
Where the last Connected is then a stable link state.
When the system is under load this may cause the unlink_urbs() work in
__handle_link_change() to not complete before the next usbnet_link_change()
call turns the carrier on again, allowing rx_submit() to queue new SKBs.
In that event the URB queue is filled faster than it can drain, ending up
in a RCU stall:
rcu: INFO: rcu_sched detected expedited stalls on CPUs/tasks: { 0-.... } 33108 jiffies s: 201 root: 0x1/.
rcu: blocking rcu_node structures (internal RCU debug):
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
Call trace:
arch_local_irq_enable+0x4/0x8
local_bh_enable+0x18/0x20
__netdev_alloc_skb+0x18c/0x1cc
rx_submit+0x68/0x1f8 [usbnet]
rx_alloc_submit+0x4c/0x74 [usbnet]
usbnet_bh+0x1d8/0x218 [usbnet]
usbnet_bh_tasklet+0x10/0x18 [usbnet]
tasklet_action_common+0xa8/0x110
tasklet_action+0x2c/0x34
handle_softirqs+0x2cc/0x3a0
__do_softirq+0x10/0x18
____do_softirq+0xc/0x14
call_on_irq_stack+0x24/0x34
do_softirq_own_stack+0x18/0x20
__irq_exit_rcu+0xa8/0xb8
irq_exit_rcu+0xc/0x30
el1_interrupt+0x34/0x48
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x68/0x6c
_raw_spin_unlock_irqrestore+0x38/0x48
xhci_urb_dequeue+0x1ac/0x45c [xhci_hcd]
unlink1+0xd4/0xdc [usbcore]
usb_hcd_unlink_urb+0x70/0xb0 [usbcore]
usb_unlink_urb+0x24/0x44 [usbcore]
unlink_urbs.constprop.0.isra.0+0x64/0xa8 [usbnet]
__handle_link_change+0x34/0x70 [usbnet]
usbnet_deferred_kevent+0x1c0/0x320 [usbnet]
process_scheduled_works+0x2d0/0x48c
worker_thread+0x150/0x1dc
kthread+0xd8/0xe8
ret_from_fork+0x10/0x20
Get around the problem by delaying the carrier on to the scheduled work.
This needs a new flag to keep track of the necessary action.
The carrier ok check cannot be removed as it remains required for the
LINK_RESET event flow.
Fixes: 4b49f58fff00 ("usbnet: handle link change")
Cc: stable@vger.kernel.org
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://patch.msgid.link/20250723102526.1305339-1-john.ernberg@actia.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fbaa6a181a4b1886cbf4214abdf9a2df68471510 upstream.
In preparation for freezer to also use saved_state, remove the
CONFIG_PREEMPT_RT compilation guard around saved_state.
On the arm64 platform I tested which did not have CONFIG_PREEMPT_RT,
there was no statistically significant deviation by applying this patch.
Test methodology:
perf bench sched message -g 40 -l 40
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Chen Ridong <chenridong@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d45cf1e7d7180256e17c9ce88e32e8061a7887fe ]
syzbot was able to craft a packet with very long IPv6 extension headers
leading to an overflow of skb->transport_header.
This 16bit field has a limited range.
Add skb_reset_transport_header_careful() helper and use it
from ipv6_gso_segment()
WARNING: CPU: 0 PID: 5871 at ./include/linux/skbuff.h:3032 skb_reset_transport_header include/linux/skbuff.h:3032 [inline]
WARNING: CPU: 0 PID: 5871 at ./include/linux/skbuff.h:3032 ipv6_gso_segment+0x15e2/0x21e0 net/ipv6/ip6_offload.c:151
Modules linked in:
CPU: 0 UID: 0 PID: 5871 Comm: syz-executor211 Not tainted 6.16.0-rc6-syzkaller-g7abc678e3084 #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/12/2025
RIP: 0010:skb_reset_transport_header include/linux/skbuff.h:3032 [inline]
RIP: 0010:ipv6_gso_segment+0x15e2/0x21e0 net/ipv6/ip6_offload.c:151
Call Trace:
<TASK>
skb_mac_gso_segment+0x31c/0x640 net/core/gso.c:53
nsh_gso_segment+0x54a/0xe10 net/nsh/nsh.c:110
skb_mac_gso_segment+0x31c/0x640 net/core/gso.c:53
__skb_gso_segment+0x342/0x510 net/core/gso.c:124
skb_gso_segment include/net/gso.h:83 [inline]
validate_xmit_skb+0x857/0x11b0 net/core/dev.c:3950
validate_xmit_skb_list+0x84/0x120 net/core/dev.c:4000
sch_direct_xmit+0xd3/0x4b0 net/sched/sch_generic.c:329
__dev_xmit_skb net/core/dev.c:4102 [inline]
__dev_queue_xmit+0x17b6/0x3a70 net/core/dev.c:4679
Fixes: d1da932ed4ec ("ipv6: Separate ipv6 offload support")
Reported-by: syzbot+af43e647fd835acc02df@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/688a1a05.050a0220.5d226.0008.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250730131738.3385939-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 52d633def56c10fe3e82a2c5d88c3ecb3f4e4852 ]
There are common patterns in the kernel of using test_and_clear_bit()
before wake_up_bit(), and atomic_dec_and_test() before wake_up_var().
These combinations don't need extra barriers but sometimes include them
unnecessarily.
To help avoid the unnecessary barriers and to help discourage the
general use of wake_up_bit/var (which is a fragile interface) introduce
two combined functions which implement these patterns.
Also add store_release_wake_up() which supports the task of simply
setting a non-atomic variable and sending a wakeup. This pattern
requires barriers which are often omitted.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240925053405.3960701-5-neilb@suse.de
Stable-dep-of: 1db3a48e83bb ("NFS: Fix wakeup of __nfs_lookup_revalidate() in unblock_revalidate()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bdc877ba6b7ff1b6d2ebeff11e63da4a50a54854 ]
The moduleparam code allows modules to provide their own definition of
MODULE_PARAM_PREFIX, instead of using the default KBUILD_MODNAME ".".
Commit 730b69d22525 ("module: check kernel param length at compile time,
not runtime") added a check to ensure the prefix doesn't exceed
MODULE_NAME_LEN, as this is what param_sysfs_builtin() expects.
Later, commit 58f86cc89c33 ("VERIFY_OCTAL_PERMISSIONS: stricter checking
for sysfs perms.") removed this check, but there is no indication this was
intentional.
Since the check is still useful for param_sysfs_builtin() to function
properly, reintroduce it in __module_param_call(), but in a modernized form
using static_assert().
While here, clean up the __module_param_call() comments. In particular,
remove the comment "Default value instead of permissions?", which comes
from commit 9774a1f54f17 ("[PATCH] Compile-time check re world-writeable
module params"). This comment was related to the test variable
__param_perm_check_##name, which was removed in the previously mentioned
commit 58f86cc89c33.
Fixes: 58f86cc89c33 ("VERIFY_OCTAL_PERMISSIONS: stricter checking for sysfs perms.")
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Reviewed-by: Daniel Gomez <da.gomez@samsung.com>
Link: https://lore.kernel.org/r/20250630143535.267745-4-petr.pavlu@suse.com
Signed-off-by: Daniel Gomez <da.gomez@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
et.al
[ Upstream commit ff7ec8dc1b646296f8d94c39339e8d3833d16c05 ]
Check pde->proc_ops->proc_lseek directly may cause UAF in rmmod scenario.
It's a gap in proc_reg_open() after commit 654b33ada4ab("proc: fix UAF in
proc_get_inode()"). Followed by AI Viro's suggestion, fix it in same
manner.
Link: https://lkml.kernel.org/r/20250607021353.1127963-1-wangzijie1@honor.com
Fixes: 3f61631d47f1 ("take care to handle NULL ->proc_lseek()")
Signed-off-by: wangzijie <wangzijie1@honor.com>
Reviewed-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Edgecombe, Rick P" <rick.p.edgecombe@intel.com>
Cc: Kirill A. Shuemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 570c8efd5eb79c3725ba439ce105ed1bedc5acd9 ]
Dietmar reported that commit 3840cbe24cf0 ("sched: psi: fix bogus
pressure spikes from aggregation race") caused a regression for him on
a high context switch rate benchmark (schbench) due to the now
repeating cpu_clock() calls.
In particular the problem is that get_recent_times() will extrapolate
the current state to 'now'. But if an update uses a timestamp from
before the start of the update, it is possible to get two reads
with inconsistent results. It is effectively back-dating an update.
(note that this all hard-relies on the clock being synchronized across
CPUs -- if this is not the case, all bets are off).
Combine this problem with the fact that there are per-group-per-cpu
seqcounts, the commit in question pushed the clock read into the group
iteration, causing tree-depth cpu_clock() calls. On architectures
where cpu_clock() has appreciable overhead, this hurts.
Instead move to a per-cpu seqcount, which allows us to have a single
clock read for all group updates, increasing internal consistency and
lowering update overhead. This comes at the cost of a longer update
side (proportional to the tree depth) which can cause the read side to
retry more often.
Fixes: 3840cbe24cf0 ("sched: psi: fix bogus pressure spikes from aggregation race")
Reported-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>,
Link: https://lkml.kernel.org/20250522084844.GC31726@noisy.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 12c409aa1ec2592280a2ddcc66ff8f3c7f7bb171 ]
Because pps_cdev_poll() returns unconditionally EPOLLIN,
a user space program that calls select/poll get always an immediate data
ready-to-read response. As a result the intended use to wait until next
data becomes ready does not work.
User space snippet:
struct pollfd pollfd = {
.fd = open("/dev/pps0", O_RDONLY),
.events = POLLIN|POLLERR,
.revents = 0 };
while(1) {
poll(&pollfd, 1, 2000/*ms*/); // returns immediate, but should wait
if(revents & EPOLLIN) { // always true
struct pps_fdata fdata;
memset(&fdata, 0, sizeof(memdata));
ioctl(PPS_FETCH, &fdata); // currently fetches data at max speed
}
}
Lets remember the last fetch event counter and compare this value
in pps_cdev_poll() with most recent event counter
and return 0 if they are equal.
Signed-off-by: Denis OSTERLAND-HEIM <denis.osterland@diehl.com>
Co-developed-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Rodolfo Giometti <giometti@enneenne.com>
Fixes: eae9d2ba0cfc ("LinuxPPS: core support")
Link: https://lore.kernel.org/all/f6bed779-6d59-4f0f-8a59-b6312bd83b4e@enneenne.com/
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Link: https://lore.kernel.org/r/c3c50ad1eb19ef553eca8a57c17f4c006413ab70.camel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ffaf1bf3737f706e4e9be876de4bc3c8fc578091 ]
The macro takes a parameter called "p" but references "fc" internally.
This happens to compile as long as callers pass a variable named fc,
but breaks otherwise. Rename the first parameter to “fc” to match the
usage and to be consistent with warnfc() / errorfc().
Fixes: a3ff937b33d9 ("prefix-handling analogues of errorf() and friends")
Signed-off-by: RubenKelevra <rubenkelevra@gmail.com>
Link: https://lore.kernel.org/20250617230927.1790401-1-rubenkelevra@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ae1ae11fb277f1335d6bcd4935ba0ea985af3c32 ]
The move of the module sanity check to earlier skipped the audit logging
call in the case of failure and to a place where the previously used
context is unavailable.
Add an audit logging call for the module loading failure case and get
the module name when possible.
Link: https://issues.redhat.com/browse/RHEL-52839
Fixes: 02da2cbab452 ("module: move check_modinfo() early to early_mod_check()")
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Reviewed-by: Petr Pavlu <petr.pavlu@suse.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0dec7201788b9152f06321d0dab46eed93834cda upstream.
In file included from drivers/crypto/intel/qat/qat_common/adf_pm_dbgfs_utils.c:4:
include/linux/sprintf.h:11:54: error: unknown type name 'va_list'
11 | __printf(2, 0) int vsprintf(char *buf, const char *, va_list);
| ^~~~~~~
include/linux/sprintf.h:1:1: note: 'va_list' is defined in header '<stdarg.h>'; this is probably fixable by adding '#include <stdarg.h>'
Link: https://lkml.kernel.org/r/20250721173754.42865913@canb.auug.org.au
Fixes: 39ced19b9e60 ("lib/vsprintf: split out sprintf() and friends")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andriy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 897e8601b9cff1d054cdd53047f568b0e1995726 ]
The s390x ISM device data sheet clearly states that only one
request-response sequence is allowable per ISM function at any point in
time. Unfortunately as of today the s390/ism driver in Linux does not
honor that requirement. This patch aims to rectify that.
This problem was discovered based on Aliaksei's bug report which states
that for certain workloads the ISM functions end up entering error state
(with PEC 2 as seen from the logs) after a while and as a consequence
connections handled by the respective function break, and for future
connection requests the ISM device is not considered -- given it is in a
dysfunctional state. During further debugging PEC 3A was observed as
well.
A kernel message like
[ 1211.244319] zpci: 061a:00:00.0: Event 0x2 reports an error for PCI function 0x61a
is a reliable indicator of the stated function entering error state
with PEC 2. Let me also point out that a kernel message like
[ 1211.244325] zpci: 061a:00:00.0: The ism driver bound to the device does not support error recovery
is a reliable indicator that the ISM function won't be auto-recovered
because the ISM driver currently lacks support for it.
On a technical level, without this synchronization, commands (inputs to
the FW) may be partially or fully overwritten (corrupted) by another CPU
trying to issue commands on the same function. There is hard evidence that
this can lead to DMB token values being used as DMB IOVAs, leading to
PEC 2 PCI events indicating invalid DMA. But this is only one of the
failure modes imaginable. In theory even completely losing one command
and executing another one twice and then trying to interpret the outputs
as if the command we intended to execute was actually executed and not
the other one is also possible. Frankly, I don't feel confident about
providing an exhaustive list of possible consequences.
Fixes: 684b89bc39ce ("s390/ism: add device driver for internal shared memory")
Reported-by: Aliaksei Makarau <Aliaksei.Makarau@ibm.com>
Tested-by: Mahanta Jambigi <mjambigi@linux.ibm.com>
Tested-by: Aliaksei Makarau <Aliaksei.Makarau@ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250722161817.1298473-1-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b16510a530d1e6ab9683f04f8fb34f2e0f538275 upstream.
Herbert notes that DIV_ROUND_UP() may overflow unnecessarily if an ecdsa
implementation's ->key_size() callback returns an unusually large value.
Herbert instead suggests (for a division by 8):
X / 8 + !!(X & 7)
Based on this formula, introduce a generic DIV_ROUND_UP_POW2() macro and
use it in lieu of DIV_ROUND_UP() for ->key_size() return values.
Additionally, use the macro in ecc_digits_from_bytes(), whose "nbytes"
parameter is a ->key_size() return value in some instances, or a
user-specified ASN.1 length in the case of ecdsa_get_signature_rs().
Link: https://lore.kernel.org/r/Z3iElsILmoSu6FuC@gondor.apana.org.au/
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 82241a83cd15aaaf28200a40ad1a8b480012edaf upstream.
On some large machines with a high number of CPUs running a 64K pagesize
kernel, we found that the 'RES' field is always 0 displayed by the top
command for some processes, which will cause a lot of confusion for users.
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
875525 root 20 0 12480 0 0 R 0.3 0.0 0:00.08 top
1 root 20 0 172800 0 0 S 0.0 0.0 0:04.52 systemd
The main reason is that the batch size of the percpu counter is quite
large on these machines, caching a significant percpu value, since
converting mm's rss stats into percpu_counter by commit f1a7941243c1 ("mm:
convert mm's rss stats into percpu_counter"). Intuitively, the batch
number should be optimized, but on some paths, performance may take
precedence over statistical accuracy. Therefore, introducing a new
interface to add the percpu statistical count and display it to users,
which can remove the confusion. In addition, this change is not expected
to be on a performance-critical path, so the modification should be
acceptable.
In addition, the 'mm->rss_stat' is updated by using add_mm_counter() and
dec/inc_mm_counter(), which are all wrappers around
percpu_counter_add_batch(). In percpu_counter_add_batch(), there is
percpu batch caching to avoid 'fbc->lock' contention. This patch changes
task_mem() and task_statm() to get the accurate mm counters under the
'fbc->lock', but this should not exacerbate kernel 'mm->rss_stat' lock
contention due to the percpu batch caching of the mm counters. The
following test also confirm the theoretical analysis.
I run the stress-ng that stresses anon page faults in 32 threads on my 32
cores machine, while simultaneously running a script that starts 32
threads to busy-loop pread each stress-ng thread's /proc/pid/status
interface. From the following data, I did not observe any obvious impact
of this patch on the stress-ng tests.
w/o patch:
stress-ng: info: [6848] 4,399,219,085,152 CPU Cycles 67.327 B/sec
stress-ng: info: [6848] 1,616,524,844,832 Instructions 24.740 B/sec (0.367 instr. per cycle)
stress-ng: info: [6848] 39,529,792 Page Faults Total 0.605 M/sec
stress-ng: info: [6848] 39,529,792 Page Faults Minor 0.605 M/sec
w/patch:
stress-ng: info: [2485] 4,462,440,381,856 CPU Cycles 68.382 B/sec
stress-ng: info: [2485] 1,615,101,503,296 Instructions 24.750 B/sec (0.362 instr. per cycle)
stress-ng: info: [2485] 39,439,232 Page Faults Total 0.604 M/sec
stress-ng: info: [2485] 39,439,232 Page Faults Minor 0.604 M/sec
On comparing a very simple app which just allocates & touches some
memory against v6.1 (which doesn't have f1a7941243c1) and latest Linus
tree (4c06e63b9203) I can see that on latest Linus tree the values for
VmRSS, RssAnon and RssFile from /proc/self/status are all zeroes while
they do report values on v6.1 and a Linus tree with this patch.
Link: https://lkml.kernel.org/r/f4586b17f66f97c174f7fd1f8647374fdb53de1c.1749119050.git.baolin.wang@linux.alibaba.com
Fixes: f1a7941243c1 ("mm: convert mm's rss stats into percpu_counter")
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Aboorva Devarajan <aboorvad@linux.ibm.com>
Tested-by: Aboorva Devarajan <aboorvad@linux.ibm.com>
Tested-by Donet Tom <donettom@linux.ibm.com>
Acked-by: Shakeel Butt <shakeel.butt@linux.dev>
Acked-by: SeongJae Park <sj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: David Hildenbrand <david@redhat.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit d8010d4ba43e9f790925375a7de100604a5e2dba upstream.
Add the required features detection glue to bugs.c et all in order to
support the TSA mitigation.
Co-developed-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cbe4134ea4bc493239786220bd69cb8a13493190 ]
Export anon_inode_make_secure_inode() to allow KVM guest_memfd to create
anonymous inodes with proper security context. This replaces the current
pattern of calling alloc_anon_inode() followed by
inode_init_security_anon() for creating security context manually.
This change also fixes a security regression in secretmem where the
S_PRIVATE flag was not cleared after alloc_anon_inode(), causing
LSM/SELinux checks to be bypassed for secretmem file descriptors.
As guest_memfd currently resides in the KVM module, we need to export this
symbol for use outside the core kernel. In the future, guest_memfd might be
moved to core-mm, at which point the symbols no longer would have to be
exported. When/if that happens is still unclear.
Fixes: 2bfe15c52612 ("mm: create security context for memfd_secret inodes")
Suggested-by: David Hildenbrand <david@redhat.com>
Suggested-by: Mike Rapoport <rppt@kernel.org>
Signed-off-by: Shivank Garg <shivankg@amd.com>
Link: https://lore.kernel.org/20250620070328.803704-3-shivankg@amd.com
Acked-by: "Mike Rapoport (Microsoft)" <rppt@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 707f853d7fa3ce323a6875487890c213e34d81a0 ]
Helper macro to more easily limit the export of a symbol to a given
list of modules.
Eg:
EXPORT_SYMBOL_GPL_FOR_MODULES(preempt_notifier_inc, "kvm");
will limit the use of said function to kvm.ko, any other module trying
to use this symbol will refure to load (and get modpost build
failures).
Requested-by: Masahiro Yamada <masahiroy@kernel.org>
Requested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Petr Pavlu <petr.pavlu@suse.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Stable-dep-of: cbe4134ea4bc ("fs: export anon_inode_make_secure_inode() and fix secretmem LSM bypass")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 33877220b8641b4cde474a4229ea92c0e3637883 ]
On at least an ASRock 990FX Extreme 4 with a VIA VT6330, the devices
have not yet been enabled by the first time ata_acpi_cbl_80wire() is
called. This means that the ata_for_each_dev loop is never entered,
and a 40 wire cable is assumed.
The VIA controller on this board does not report the cable in the PCI
config space, thus having to fall back to ACPI even though no SATA
bridge is present.
The _GTM values are correctly reported by the firmware through ACPI,
which has already set up faster transfer modes, but due to the above
the controller is forced down to a maximum of UDMA/33.
Resolve this by modifying ata_acpi_cbl_80wire() to directly return the
cable type. First, an unknown cable is assumed which preserves the mode
set by the firmware, and then on subsequent calls when the devices have
been enabled, an 80 wire cable is correctly detected.
Since the function now directly returns the cable type, it is renamed
to ata_acpi_cbl_pata_type().
Signed-off-by: Tasos Sahanidis <tasos@tasossah.com>
Link: https://lore.kernel.org/r/20250519085945.1399466-1-tasos@tasossah.com
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit af4db5a35a4ef7a68046883bfd12468007db38f1 upstream.
A poorly implemented DisplayPort Alt Mode port partner can indicate
that its pin assignment capabilities are greater than the maximum
value, DP_PIN_ASSIGN_F. In this case, calls to pin_assignment_show
will cause a BRK exception due to an out of bounds array access.
Prevent for loop in pin_assignment_show from accessing
invalid values in pin_assignments by adding DP_PIN_ASSIGN_MAX
value in typec_dp.h and using i < DP_PIN_ASSIGN_MAX as a loop
condition.
Fixes: 0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250618224943.3263103-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 8ebf2709fe4dcd0a1b7b95bf61e529ddcd3cdf51 which is
commit a18dfa9925b9ef6107ea3aa5814ca3c704d34a8a upstream.
A regression was introduced when backporting this to the stable kernels
without applying previous commits in this series.
When sending IPv6 UDP packets larger than MTU, EMSGSIZE was returned
instead of fragmenting the packets as expected.
As there is no compelling reason for this commit to be present in the
stable kernels it should be reverted.
Signed-off-by: Brett A C Sheffield <bacs@librecast.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8d5cc8eed738e3202379722295c626cba0849785 ]
The non-zero (true) return value from consw::con_switch() means a redraw
is needed. So make this return type a bool explicitly instead of int.
The latter might imply that -Eerrors are expected. They are not.
And document the hook.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-parisc@vger.kernel.org
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-31-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 03bcbbb3995b ("dummycon: Trigger redraw when switching consoles with deferred takeover")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 559f01a0ee6d924c6fec3eaf6a5b078b15e71070 ]
In consw::con_clear():
* Height is always 1, so drop it.
* Offsets and width are always unsigned values, so re-type them as such.
This needs a new __fbcon_clear() in the fbcon code to still handle
height which might not be 1 when called internally.
Note that tests for negative count/width are left in place -- they are
taken care of in the next patches.
And document the hook.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-parisc@vger.kernel.org
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-22-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 03bcbbb3995b ("dummycon: Trigger redraw when switching consoles with deferred takeover")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dae3e6b6180f1a2394b984c596d39ed2c57d25fe ]
The 'init' parameter of consw::con_init() is true for the first call of
the hook on a particular console. So make the parameter a bool.
And document the hook.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-parisc@vger.kernel.org
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-21-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 03bcbbb3995b ("dummycon: Trigger redraw when switching consoles with deferred takeover")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e8c4bd6c6e6b7e7b416c42806981c2a81370001e ]
Add a function to query for the preferred ring buffer size of VMBus
device. This will allow the drivers (eg. UIO) to allocate the most
optimized ring buffer size for devices.
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Link: https://lore.kernel.org/r/1711788723-8593-2-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 0315fef2aff9 ("uio_hv_generic: Align ring size to system page")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f22b4b55edb507a2b30981e133b66b642be4d13f upstream.
I find the behavior of xa_for_each_start() slightly counter-intuitive.
It doesn't end the iteration by making the index point after the last
element. IOW calling xa_for_each_start() again after it "finished"
will run the body of the loop for the last valid element, instead
of doing nothing.
This works fine for netlink dumps if they terminate correctly
(i.e. coalesce or carefully handle NLM_DONE), but as we keep getting
reminded legacy dumps are unlikely to go away.
Fixing this generically at the xa_for_each_start() level seems hard -
there is no index reserved for "end of iteration".
ifindexes are 31b wide, tho, and iterator is ulong so for
for_each_netdev_dump() it's safe to go to the next element.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ The mctp RTM_GETADDR rework backport of acab78ae12c7 ("net: mctp: Don't
access ifa_index when missing") pulled 2d45eeb7d5d7 ("mctp: no longer
rely on net->dev_index_head[]") as a dependency. However, that change
relies on this backport for correct behaviour of
for_each_netdev_dump().
Jakub mentions[1] that nothing should be relying on the old behaviour
of for_each_netdev_dump(), hence the backport.
[1]: https://lore.kernel.org/netdev/20250609083749.741c27f5@kernel.org/ ]
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 081056dc00a27bccb55ccc3c6f230a3d5fd3f7e0 upstream.
Currently, __split_vma() triggers hugetlb page table unsharing through
vm_ops->may_split(). This happens before the VMA lock and rmap locks are
taken - which is too early, it allows racing VMA-locked page faults in our
process and racing rmap walks from other processes to cause page tables to
be shared again before we actually perform the split.
Fix it by explicitly calling into the hugetlb unshare logic from
__split_vma() in the same place where THP splitting also happens. At that
point, both the VMA and the rmap(s) are write-locked.
An annoying detail is that we can now call into the helper
hugetlb_unshare_pmds() from two different locking contexts:
1. from hugetlb_split(), holding:
- mmap lock (exclusively)
- VMA lock
- file rmap lock (exclusively)
2. hugetlb_unshare_all_pmds(), which I think is designed to be able to
call us with only the mmap lock held (in shared mode), but currently
only runs while holding mmap lock (exclusively) and VMA lock
Backporting note:
This commit fixes a racy protection that was introduced in commit
b30c14cd6102 ("hugetlb: unshare some PMDs when splitting VMAs"); that
commit claimed to fix an issue introduced in 5.13, but it should actually
also go all the way back.
[jannh@google.com: v2]
Link: https://lkml.kernel.org/r/20250528-hugetlb-fixes-splitrace-v2-1-1329349bad1a@google.com
Link: https://lkml.kernel.org/r/20250528-hugetlb-fixes-splitrace-v2-0-1329349bad1a@google.com
Link: https://lkml.kernel.org/r/20250527-hugetlb-fixes-splitrace-v1-1-f4136f5ec58a@google.com
Fixes: 39dde65c9940 ("[PATCH] shared page table for hugetlb page")
Signed-off-by: Jann Horn <jannh@google.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org> [b30c14cd6102: hugetlb: unshare some PMDs when splitting VMAs]
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[stable backport: code got moved from mmap.c to vma.c]
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7851263998d4269125fd6cb3fdbfc7c6db853859 upstream.
In vcc_sendmsg(), we account skb->truesize to sk->sk_wmem_alloc by
atm_account_tx().
It is expected to be reverted by atm_pop_raw() later called by
vcc->dev->ops->send(vcc, skb).
However, vcc_sendmsg() misses the same revert when copy_from_iter_full()
fails, and then we will leak a socket.
Let's factorise the revert part as atm_return_tx() and call it in
the failure path.
Note that the corresponding sk_wmem_alloc operation can be found in
alloc_tx() as of the blamed commit.
$ git blame -L:alloc_tx net/atm/common.c c55fa3cccbc2c~
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20250614161959.GR414686@horms.kernel.org/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250616182147.963333-3-kuni1840@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e1bdbbc98279164d910d2de82a745f090a8b249f ]
acpi_register_lps0_dev() and acpi_unregister_lps0_dev() may be used
in drivers that don't require CONFIG_SUSPEND or compile on !X86.
Add prototypes for those cases.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202502191627.fRgoBwcZ-lkp@intel.com/
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20250407183656.1503446-1-superm1@kernel.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9510b38dc0ba358c93cbf5ee7c28820afb85937b ]
Adds the MMC_QUIRK_NO_UHS_DDR50_TUNING quirk and updates
mmc_execute_tuning() to return 0 if that quirk is set. This fixes an
issue on certain Swissbit SD cards that do not support DDR50 tuning
where tuning requests caused I/O errors to be thrown.
Signed-off-by: Erick Shepherd <erick.shepherd@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250331221337.1414534-1-erick.shepherd@ni.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Commit 95041b93e90a06bb613ec4bef9cd4d61570f68e4 upstream.
This adds a flag to avoid dipping dereferencing file and then f_op to
figure out if the file has a poll handler defined or not. We generally
call this at least twice for networked workloads, and if using ring
provided buffers, we do it on every buffer selection. Particularly the
latter is troublesome, as it's otherwise a very fast operation.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fe7f7ac8e0c708446ff017453add769ffc15deed upstream.
Update struct hid_descriptor to better reflect the mandatory and
optional parts of the HID Descriptor as per USB HID 1.11 specification.
Note: the kernel currently does not parse any optional HID class
descriptors, only the mandatory report descriptor.
Update all references to member element desc[0] to rpt_desc.
Add test to verify bLength and bNumDescriptors values are valid.
Replace the for loop with direct access to the mandatory HID class
descriptor member for the report descriptor. This eliminates the
possibility of getting an out-of-bounds fault.
Add a warning message if the HID descriptor contains any unsupported
optional HID class descriptors.
Reported-by: syzbot+c52569baf0c843f35495@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c52569baf0c843f35495
Fixes: f043bfc98c19 ("HID: usbhid: fix out-of-bounds bug")
Cc: stable@vger.kernel.org
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5e223e06ee7c6d8f630041a0645ac90e39a42cc6 ]
Similarly to 26064d3e2b4d ("block: fix adding folio to bio"), if
we attempt to add a folio that is larger than 4GB, we'll silently
truncate the offset and len. Widen the parameters to size_t, assert
that the length is less than 4GB and set the first page that contains
the interesting data rather than the first page of the folio.
Fixes: 26db5ee15851 (block: add a bvec_set_folio helper)
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lore.kernel.org/r/20250612144255.2850278-1-willy@infradead.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f826ec7966a63d48e16e0868af4e038bf9a1a3ae ]
It is possible for physically contiguous folios to have discontiguous
struct pages if SPARSEMEM is enabled and SPARSEMEM_VMEMMAP is not.
This is correctly handled by folio_page_idx(), so remove this open-coded
implementation.
Fixes: 640d1930bef4 (block: Add bio_for_each_folio_all())
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lore.kernel.org/r/20250612144126.2849931-1-willy@infradead.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e9cb929670a1e98b592b30f03f06e9e20110f318 ]
Both to_mdio_device() and to_phy_device() "throw away" the const pointer
attribute passed to them and return a non-const pointer, which generally
is not a good thing overall. Fix this up by using container_of_const()
which was designed for this very problem.
Cc: Alexander Lobakin <alobakin@pm.me>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Fixes: 7eab14de73a8 ("mdio, phy: fix -Wshadow warnings triggered by nested container_of()")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2025052246-conduit-glory-8fc9@gregkh
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5d2ea5aebbb2f3ebde4403f9c55b2b057e5dd2d6 ]
Upon RQ destruction if the firmware command fails which is the
last resource to be destroyed some SW resources were already cleaned
regardless of the failure.
Now properly rollback the object to its original state upon such failure.
In order to avoid a use-after free in case someone tries to destroy the
object again, which results in the following kernel trace:
refcount_t: underflow; use-after-free.
WARNING: CPU: 0 PID: 37589 at lib/refcount.c:28 refcount_warn_saturate+0xf4/0x148
Modules linked in: rdma_ucm(OE) rdma_cm(OE) iw_cm(OE) ib_ipoib(OE) ib_cm(OE) ib_umad(OE) mlx5_ib(OE) rfkill mlx5_core(OE) mlxdevm(OE) ib_uverbs(OE) ib_core(OE) psample mlxfw(OE) mlx_compat(OE) macsec tls pci_hyperv_intf sunrpc vfat fat virtio_net net_failover failover fuse loop nfnetlink vsock_loopback vmw_vsock_virtio_transport_common vmw_vsock_vmci_transport vmw_vmci vsock xfs crct10dif_ce ghash_ce sha2_ce sha256_arm64 sha1_ce virtio_console virtio_gpu virtio_blk virtio_dma_buf virtio_mmio dm_mirror dm_region_hash dm_log dm_mod xpmem(OE)
CPU: 0 UID: 0 PID: 37589 Comm: python3 Kdump: loaded Tainted: G OE ------- --- 6.12.0-54.el10.aarch64 #1
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : refcount_warn_saturate+0xf4/0x148
lr : refcount_warn_saturate+0xf4/0x148
sp : ffff80008b81b7e0
x29: ffff80008b81b7e0 x28: ffff000133d51600 x27: 0000000000000001
x26: 0000000000000000 x25: 00000000ffffffea x24: ffff00010ae80f00
x23: ffff00010ae80f80 x22: ffff0000c66e5d08 x21: 0000000000000000
x20: ffff0000c66e0000 x19: ffff00010ae80340 x18: 0000000000000006
x17: 0000000000000000 x16: 0000000000000020 x15: ffff80008b81b37f
x14: 0000000000000000 x13: 2e656572662d7265 x12: ffff80008283ef78
x11: ffff80008257efd0 x10: ffff80008283efd0 x9 : ffff80008021ed90
x8 : 0000000000000001 x7 : 00000000000bffe8 x6 : c0000000ffff7fff
x5 : ffff0001fb8e3408 x4 : 0000000000000000 x3 : ffff800179993000
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000133d51600
Call trace:
refcount_warn_saturate+0xf4/0x148
mlx5_core_put_rsc+0x88/0xa0 [mlx5_ib]
mlx5_core_destroy_rq_tracked+0x64/0x98 [mlx5_ib]
mlx5_ib_destroy_wq+0x34/0x80 [mlx5_ib]
ib_destroy_wq_user+0x30/0xc0 [ib_core]
uverbs_free_wq+0x28/0x58 [ib_uverbs]
destroy_hw_idr_uobject+0x34/0x78 [ib_uverbs]
uverbs_destroy_uobject+0x48/0x240 [ib_uverbs]
__uverbs_cleanup_ufile+0xd4/0x1a8 [ib_uverbs]
uverbs_destroy_ufile_hw+0x48/0x120 [ib_uverbs]
ib_uverbs_close+0x2c/0x100 [ib_uverbs]
__fput+0xd8/0x2f0
__fput_sync+0x50/0x70
__arm64_sys_close+0x40/0x90
invoke_syscall.constprop.0+0x74/0xd0
do_el0_svc+0x48/0xe8
el0_svc+0x44/0x1d0
el0t_64_sync_handler+0x120/0x130
el0t_64_sync+0x1a4/0x1a8
Fixes: e2013b212f9f ("net/mlx5_core: Add RQ and SQ event handling")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Link: https://patch.msgid.link/3181433ccdd695c63560eeeb3f0c990961732101.1745839855.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 59529bbe642de4eb2191a541d9b4bae7eb73862e ]
SDEI usually initialize with the ACPI table, but on platforms where
ACPI is not used, the SDEI feature can still be used to handle
specific firmware calls or other customized purposes. Therefore, it
is not necessary for ARM_SDE_INTERFACE to depend on ACPI_APEI_GHES.
In commit dc4e8c07e9e2 ("ACPI: APEI: explicit init of HEST and GHES
in acpi_init()"), to make APEI ready earlier, sdei_init was moved
into acpi_ghes_init instead of being a standalone initcall, adding
ACPI_APEI_GHES dependency to ARM_SDE_INTERFACE. This restricts the
flexibility and usability of SDEI.
This patch corrects the dependency in Kconfig and splits sdei_init()
into two separate functions: sdei_init() and acpi_sdei_init().
sdei_init() will be called by arch_initcall and will only initialize
the platform driver, while acpi_sdei_init() will initialize the
device from acpi_ghes_init() when ACPI is ready. This allows the
initialization of SDEI without ACPI_APEI_GHES enabled.
Fixes: dc4e8c07e9e2 ("ACPI: APEI: explicit init of HEST and GHES in apci_init()")
Cc: Shuai Xue <xueshuai@linux.alibaba.com>
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Reviewed-by: Shuai Xue <xueshuai@linux.alibaba.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20250507045757.2658795-1-quic_hyiwei@quicinc.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dcd21b609d4abc7303f8683bce4f35d78d7d6830 ]
The Linux client assumes that all filehandles are non-volatile for
renames within the same directory (otherwise sillyrename cannot work).
However, the existence of the Linux 'subtree_check' export option has
meant that nfs_rename() has always assumed it needs to flush writes
before attempting to rename.
Since NFSv4 does allow the client to query whether or not the server
exhibits this behaviour, and since knfsd does actually set the
appropriate flag when 'subtree_check' is enabled on an export, it
should be OK to optimise away the write flushing behaviour in the cases
where it is clearly not needed.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b5325b2a270fcaf7b2a9a0f23d422ca8a5a8bdea upstream.
Give userspace a way to instruct the kernel to install a pidfd into the
usermode helper process. This makes coredump handling a lot more
reliable for userspace. In parallel with this commit we already have
systemd adding support for this in [1].
We create a pidfs file for the coredumping process when we process the
corename pattern. When the usermode helper process is forked we then
install the pidfs file as file descriptor three into the usermode
helpers file descriptor table so it's available to the exec'd program.
Since usermode helpers are either children of the system_unbound_wq
workqueue or kthreadd we know that the file descriptor table is empty
and can thus always use three as the file descriptor number.
Note, that we'll install a pidfd for the thread-group leader even if a
subthread is calling do_coredump(). We know that task linkage hasn't
been removed due to delay_group_leader() and even if this @current isn't
the actual thread-group leader we know that the thread-group leader
cannot be reaped until @current has exited.
[brauner: This is a backport for the v6.6 series. Upsteam has
significantly changed and backporting all that infra is a non-starter.
So simply use the pidfd_prepare() helper and waste the file descriptor
we allocated. Then we minimally massage the umh coredump setup code.]
Link: https://github.com/systemd/systemd/pull/37125 [1]
Link: https://lore.kernel.org/20250414-work-coredump-v2-3-685bf231f828@kernel.org
Tested-by: Luca Boccassi <luca.boccassi@gmail.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 53dac345395c0d2493cbc2f4c85fe38aef5b63f5 upstream.
hrtimers are migrated away from the dying CPU to any online target at
the CPUHP_AP_HRTIMERS_DYING stage in order not to delay bandwidth timers
handling tasks involved in the CPU hotplug forward progress.
However wakeups can still be performed by the outgoing CPU after
CPUHP_AP_HRTIMERS_DYING. Those can result again in bandwidth timers being
armed. Depending on several considerations (crystal ball power management
based election, earliest timer already enqueued, timer migration enabled or
not), the target may eventually be the current CPU even if offline. If that
happens, the timer is eventually ignored.
The most notable example is RCU which had to deal with each and every of
those wake-ups by deferring them to an online CPU, along with related
workarounds:
_ e787644caf76 (rcu: Defer RCU kthreads wakeup when CPU is dying)
_ 9139f93209d1 (rcu/nocb: Fix RT throttling hrtimer armed from offline CPU)
_ f7345ccc62a4 (rcu/nocb: Fix rcuog wake-up from offline softirq)
The problem isn't confined to RCU though as the stop machine kthread
(which runs CPUHP_AP_HRTIMERS_DYING) reports its completion at the end
of its work through cpu_stop_signal_done() and performs a wake up that
eventually arms the deadline server timer:
WARNING: CPU: 94 PID: 588 at kernel/time/hrtimer.c:1086 hrtimer_start_range_ns+0x289/0x2d0
CPU: 94 UID: 0 PID: 588 Comm: migration/94 Not tainted
Stopper: multi_cpu_stop+0x0/0x120 <- stop_machine_cpuslocked+0x66/0xc0
RIP: 0010:hrtimer_start_range_ns+0x289/0x2d0
Call Trace:
<TASK>
start_dl_timer
enqueue_dl_entity
dl_server_start
enqueue_task_fair
enqueue_task
ttwu_do_activate
try_to_wake_up
complete
cpu_stopper_thread
Instead of providing yet another bandaid to work around the situation, fix
it in the hrtimers infrastructure instead: always migrate away a timer to
an online target whenever it is enqueued from an offline CPU.
This will also allow to revert all the above RCU disgraceful hacks.
Fixes: 5c0930ccaad5 ("hrtimers: Push pending hrtimers away from outgoing CPU earlier")
Reported-by: Vlad Poenaru <vlad.wing@gmail.com>
Reported-by: Usama Arif <usamaarif642@gmail.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/all/20250117232433.24027-1-frederic@kernel.org
Closes: 20241213203739.1519801-1-usamaarif642@gmail.com
Signed-off-by: Zhaoyang Li <lizy04@hust.edu.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 97dfbbd135cb5e4426f37ca53a8fa87eaaa4e376 upstream.
In commit c749d9b7ebbc ("iov_iter: fix copy_page_from_iter_atomic() if
KMAP_LOCAL_FORCE_MAP"), Hugh correctly noted that if KMAP_LOCAL_FORCE_MAP
is enabled, we must limit ourselves to PAGE_SIZE bytes per call to
kmap_local(). The same problem exists in memcpy_from_folio(),
memcpy_to_folio(), folio_zero_tail(), folio_fill_tail() and
memcpy_from_file_folio(), so add folio_test_partial_kmap() to do this more
succinctly.
Link: https://lkml.kernel.org/r/20250514170607.3000994-2-willy@infradead.org
Fixes: 00cdf76012ab ("mm: add memcpy_from_file_folio()")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8ce939a0fa194939cc1f92dbd8bc1a7806e7d40a ]
The event may have been updated in the PMU-specific implementation,
e.g., Intel PEBS counters snapshotting. The common code should not
read and overwrite the value.
The PERF_SAMPLE_READ in the data->sample_type can be used to detect
whether the PMU-specific value is available. If yes, avoid the
pmu->read() in the common code. Add a new flag, skip_read, to track the
case.
Factor out a perf_pmu_read() to clean up the code.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20250121152303.3128733-3-kan.liang@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ad6b5b73ff565e88aca7a7d1286788d80c97ba71 ]
rcu_all_qs() is defined for !CONFIG_PREEMPT_RCU but the declaration
is conditioned on CONFIG_PREEMPTION.
With CONFIG_PREEMPT_LAZY, CONFIG_PREEMPTION=y does not imply
CONFIG_PREEMPT_RCU=y.
Decouple the two.
Cc: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fcf0e25ad4c8d14d2faab4d9a17040f31efce205 ]
rcu_read_unlock_strict() can be called with preemption enabled
which can make for an unstable rdp and a racy norm value.
Fix this by dropping the preempt-count in __rcu_read_unlock()
after the call to rcu_read_unlock_strict(), adjusting the
preempt-count check appropriately.
Suggested-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 848b09d53d923b4caee5491f57a5c5b22d81febc ]
The Dell AW1022z is an RTL8156B based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://patch.msgid.link/20250206224033.980115-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4a6f18f28627e121bd1f74b5fcc9f945d6dbeb1e ]
GCC can see that the value range for "order" is capped, but this leads
it to consider that it might be negative, leading to a false positive
warning (with GCC 15 with -Warray-bounds -fdiagnostics-details):
../drivers/net/ethernet/mellanox/mlx4/alloc.c:691:47: error: array subscript -1 is below array bounds of 'long unsigned int *[2]' [-Werror=array-bounds=]
691 | i = find_first_bit(pgdir->bits[o], MLX4_DB_PER_PAGE >> o);
| ~~~~~~~~~~~^~~
'mlx4_alloc_db_from_pgdir': events 1-2
691 | i = find_first_bit(pgdir->bits[o], MLX4_DB_PER_PAGE >> o); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| | | | | (2) out of array bounds here
| (1) when the condition is evaluated to true In file included from ../drivers/net/ethernet/mellanox/mlx4/mlx4.h:53,
from ../drivers/net/ethernet/mellanox/mlx4/alloc.c:42:
../include/linux/mlx4/device.h:664:33: note: while referencing 'bits'
664 | unsigned long *bits[2];
| ^~~~
Switch the argument to unsigned int, which removes the compiler needing
to consider negative values.
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20250210174504.work.075-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1f7df3a691740a7736bbc99dc4ed536120eb4746 ]
The IOMMU translation for MSI message addresses has been a 2-step process,
separated in time:
1) iommu_dma_prepare_msi(): A cookie pointer containing the IOVA address
is stored in the MSI descriptor when an MSI interrupt is allocated.
2) iommu_dma_compose_msi_msg(): this cookie pointer is used to compute a
translated message address.
This has an inherent lifetime problem for the pointer stored in the cookie
that must remain valid between the two steps. However, there is no locking
at the irq layer that helps protect the lifetime. Today, this works under
the assumption that the iommu domain is not changed while MSI interrupts
being programmed. This is true for normal DMA API users within the kernel,
as the iommu domain is attached before the driver is probed and cannot be
changed while a driver is attached.
Classic VFIO type1 also prevented changing the iommu domain while VFIO was
running as it does not support changing the "container" after starting up.
However, iommufd has improved this so that the iommu domain can be changed
during VFIO operation. This potentially allows userspace to directly race
VFIO_DEVICE_ATTACH_IOMMUFD_PT (which calls iommu_attach_group()) and
VFIO_DEVICE_SET_IRQS (which calls into iommu_dma_compose_msi_msg()).
This potentially causes both the cookie pointer and the unlocked call to
iommu_get_domain_for_dev() on the MSI translation path to become UAFs.
Fix the MSI cookie UAF by removing the cookie pointer. The translated IOVA
address is already known during iommu_dma_prepare_msi() and cannot change.
Thus, it can simply be stored as an integer in the MSI descriptor.
The other UAF related to iommu_get_domain_for_dev() will be addressed in
patch "iommu: Make iommu_dma_prepare_msi() into a generic operation" by
using the IOMMU group mutex.
Link: https://patch.msgid.link/r/a4f2cd76b9dc1833ee6c1cf325cba57def22231c.1740014950.git.nicolinc@nvidia.com
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 80df31f384b4146a62a01b3d4beb376cc7b9a89e ]
Change POOL_NEXT_SIZE define value from 0 to BIT(30), since this define
is used to request the available maximum sized flow table, and zero doesn't
make sense for it, whereas some places in the driver use zero explicitly
expecting the smallest table size possible but instead due to this
define they end up allocating the biggest table size unawarely.
In addition move the definition to "include/linux/mlx5/fs.h" to expose the
define to IB driver as well, while appropriately renaming it.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250219085808.349923-3-tariqt@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cc47f07234f72cbd8e2c973cdbf2a6730660a463 ]
Unlike the decompression code, the compression code in LZO never
checked for output overruns. It instead assumes that the caller
always provides enough buffer space, disregarding the buffer length
provided by the caller.
Add a safe compression interface that checks for the end of buffer
before each write. Use the safe interface in crypto/lzo.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a18dfa9925b9ef6107ea3aa5814ca3c704d34a8a ]
When spanning datagram construction over multiple send calls using
MSG_MORE, per datagram settings are configured on the first send.
That is when ip(6)_setup_cork stores these settings for subsequent use
in __ip(6)_append_data and others.
The only flag that escaped this was dontfrag. As a result, a datagram
could be constructed with df=0 on the first sendmsg, but df=1 on a
next. Which is what cmsg_ip.sh does in an upcoming MSG_MORE test in
the "diff" scenario.
Changing datagram conditions in the middle of constructing an skb
makes this already complex code path even more convoluted. It is here
unintentional. Bring this flag in line with expected sockopt/cmsg
behavior.
And stop passing ipc6 to __ip6_append_data, to avoid such issues
in the future. This is already the case for __ip_append_data.
inet6_cork had a 6 byte hole, so the 1B flag has no impact.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250307033620.411611-3-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4b82b181a26cff8bf7adc3a85a88d121d92edeaf ]
Currently for bpf progs in a cgroup hierarchy, the effective prog array
is computed from bottom cgroup to upper cgroups (post-ordering). For
example, the following cgroup hierarchy
root cgroup: p1, p2
subcgroup: p3, p4
have BPF_F_ALLOW_MULTI for both cgroup levels.
The effective cgroup array ordering looks like
p3 p4 p1 p2
and at run time, progs will execute based on that order.
But in some cases, it is desirable to have root prog executes earlier than
children progs (pre-ordering). For example,
- prog p1 intends to collect original pkt dest addresses.
- prog p3 will modify original pkt dest addresses to a proxy address for
security reason.
The end result is that prog p1 gets proxy address which is not what it
wants. Putting p1 to every child cgroup is not desirable either as it
will duplicate itself in many child cgroups. And this is exactly a use case
we are encountering in Meta.
To fix this issue, let us introduce a flag BPF_F_PREORDER. If the flag
is specified at attachment time, the prog has higher priority and the
ordering with that flag will be from top to bottom (pre-ordering).
For example, in the above example,
root cgroup: p1, p2
subcgroup: p3, p4
Let us say p2 and p4 are marked with BPF_F_PREORDER. The final
effective array ordering will be
p2 p4 p3 p1
Suggested-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20250224230116.283071-1-yonghong.song@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
