| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit e8ee6c8cb61b676f1a2d6b942329e98224bd8ee9 ]
DW DMA IP-core provides a way to synthesize the DMA controller with
channels having different parameters like maximum burst-length,
multi-block support, maximum data width, etc. Those parameters both
explicitly and implicitly affect the channels performance. Since DMA slave
devices might be very demanding to the DMA performance, let's provide a
functionality for the slaves to be assigned with DW DMA channels, which
performance according to the platform engineer fulfill their requirements.
After this patch is applied it can be done by passing the mask of suitable
DMA-channels either directly in the dw_dma_slave structure instance or as
a fifth cell of the DMA DT-property. If mask is zero or not provided, then
there is no limitation on the channels allocation.
For instance Baikal-T1 SoC is equipped with a DW DMAC engine, which first
two channels are synthesized with max burst length of 16, while the rest
of the channels have been created with max-burst-len=4. It would seem that
the first two channels must be faster than the others and should be more
preferable for the time-critical DMA slave devices. In practice it turned
out that the situation is quite the opposite. The channels with
max-burst-len=4 demonstrated a better performance than the channels with
max-burst-len=16 even when they both had been initialized with the same
settings. The performance drop of the first two DMA-channels made them
unsuitable for the DW APB SSI slave device. No matter what settings they
are configured with, full-duplex SPI transfers occasionally experience the
Rx FIFO overflow. It means that the DMA-engine doesn't keep up with
incoming data pace even though the SPI-bus is enabled with speed of 25MHz
while the DW DMA controller is clocked with 50MHz signal. There is no such
problem has been noticed for the channels synthesized with
max-burst-len=4.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200731200826.9292-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f959dcd6ddfd29235030e8026471ac1b022ad2b0 ]
When booting the kernel v5.9-rc4 on a VM, the kernel would panic when
printing a warning message in swiotlb_map(). The dev->dma_mask must not
be a NULL pointer when calling the dma mapping layer. A NULL pointer
check can potentially avoid the panic.
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7f6e4312e15a5c370e84eaa685879b6bdcc717e4 ]
Protect against potential stack overflow that might happen when bpf2bpf
calls get combined with tailcalls. Limit the caller's stack depth for
such case down to 256 so that the worst case scenario would result in 8k
stack size (32 which is tailcall limit * 256 = 8k).
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 70d932985757fbe978024db313001218e9f8fe5c ]
The current notifiers have the following error handling pattern all
over the place:
int err, nr;
err = __foo_notifier_call_chain(&chain, val_up, v, -1, &nr);
if (err & NOTIFIER_STOP_MASK)
__foo_notifier_call_chain(&chain, val_down, v, nr-1, NULL)
And aside from the endless repetition thereof, it is broken. Consider
blocking notifiers; both calls take and drop the rwsem, this means
that the notifier list can change in between the two calls, making @nr
meaningless.
Fix this by replacing all the __foo_notifier_call_chain() functions
with foo_notifier_call_chain_robust() that embeds the above pattern,
but ensures it is inside a single lock region.
Note: I switched atomic_notifier_call_chain_robust() to use
the spinlock, since RCU cannot provide the guarantee
required for the recovery.
Note: software_resume() error handling was broken afaict.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20200818135804.325626653@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c51f8f88d705e06bd696d7510aff22b33eb8e638 ]
Non-cryptographic PRNGs may have great statistical properties, but
are usually trivially predictable to someone who knows the algorithm,
given a small sample of their output. An LFSR like prandom_u32() is
particularly simple, even if the sample is widely scattered bits.
It turns out the network stack uses prandom_u32() for some things like
random port numbers which it would prefer are *not* trivially predictable.
Predictability led to a practical DNS spoofing attack. Oops.
This patch replaces the LFSR with a homebrew cryptographic PRNG based
on the SipHash round function, which is in turn seeded with 128 bits
of strong random key. (The authors of SipHash have *not* been consulted
about this abuse of their algorithm.) Speed is prioritized over security;
attacks are rare, while performance is always wanted.
Replacing all callers of prandom_u32() is the quick fix.
Whether to reinstate a weaker PRNG for uses which can tolerate it
is an open question.
Commit f227e3ec3b5c ("random32: update the net random state on interrupt
and activity") was an earlier attempt at a solution. This patch replaces
it.
Reported-by: Amit Klein <aksecurity@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Fixes: f227e3ec3b5c ("random32: update the net random state on interrupt and activity")
Signed-off-by: George Spelvin <lkml@sdf.org>
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
[ willy: partial reversal of f227e3ec3b5c; moved SIPROUND definitions
to prandom.h for later use; merged George's prandom_seed() proposal;
inlined siprand_u32(); replaced the net_rand_state[] array with 4
members to fix a build issue; cosmetic cleanups to make checkpatch
happy; fixed RANDOM32_SELFTEST build ]
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 23c22299cd290409c6b78f57c42b64f8dfb6dd92 ]
Add clear parameter to let client decide if
event should be clear to 0 after GCE receive it.
Signed-off-by: Dennis YC Hsieh <dennis-yc.hsieh@mediatek.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/1594136714-11650-9-git-send-email-dennis-yc.hsieh@mediatek.com
[mb: fix commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0cfcd405e758ba1d277e58436fb32f06888c3e41 ]
NFS_FS=y as dependency of CONFIG_NFSD_V4_2_INTER_SSC still have
build errors and some configs with NFSD=m to get NFS4ERR_STALE
error when doing inter server copy.
Added ops table in nfs_common for knfsd to access NFS client modules.
Fixes: 3ac3711adb88 ("NFSD: Fix NFS server build errors")
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 12856e7acde4702b7c3238c15fcba86ff6aa507f ]
For VFs, the Memory Space Enable bit in the Command Register is
hard-wired to 0.
Add a new bit to signify devices where the Command Register Memory
Space Enable bit does not control the device's response to MMIO
accesses.
Fixes: abafbc551fdd ("vfio-pci: Invalidate mmaps and block MMIO access on disabled memory")
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8fb156c9ee2db94f7127c930c89917634a1a9f56 ]
The implementation of split_page_owner() prefers a count rather than the
old order of the page. When we support a variable size THP, we won't
have the order at this point, but we will have the number of pages.
So change the interface to what the caller and callee would prefer.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: SeongJae Park <sjpark@amazon.de>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Link: https://lkml.kernel.org/r/20200908195539.25896-4-willy@infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a4947e84f23474803b62a2759b5808147e4e15f9 ]
The various array_size functions use SIZE_MAX define, but missed limits.h
causes to failure to compile code that needs overflow.h.
In file included from drivers/infiniband/core/uverbs_std_types_device.c:6:
./include/linux/overflow.h: In function 'array_size':
./include/linux/overflow.h:258:10: error: 'SIZE_MAX' undeclared (first use in this function)
258 | return SIZE_MAX;
| ^~~~~~~~
Fixes: 610b15c50e86 ("overflow.h: Add allocation size calculation helpers")
Link: https://lore.kernel.org/r/20200913102928.134985-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 67197a4f28d28d0b073ab0427b03cb2ee5382578 ]
Currently __set_oom_adj loops through all processes in the system to keep
oom_score_adj and oom_score_adj_min in sync between processes sharing
their mm. This is done for any task with more that one mm_users, which
includes processes with multiple threads (sharing mm and signals).
However for such processes the loop is unnecessary because their signal
structure is shared as well.
Android updates oom_score_adj whenever a tasks changes its role
(background/foreground/...) or binds to/unbinds from a service, making it
more/less important. Such operation can happen frequently. We noticed
that updates to oom_score_adj became more expensive and after further
investigation found out that the patch mentioned in "Fixes" introduced a
regression. Using Pixel 4 with a typical Android workload, write time to
oom_score_adj increased from ~3.57us to ~362us. Moreover this regression
linearly depends on the number of multi-threaded processes running on the
system.
Mark the mm with a new MMF_MULTIPROCESS flag bit when task is created with
(CLONE_VM && !CLONE_THREAD && !CLONE_VFORK). Change __set_oom_adj to use
MMF_MULTIPROCESS instead of mm_users to decide whether oom_score_adj
update should be synchronized between multiple processes. To prevent
races between clone() and __set_oom_adj(), when oom_score_adj of the
process being cloned might be modified from userspace, we use
oom_adj_mutex. Its scope is changed to global.
The combination of (CLONE_VM && !CLONE_THREAD) is rarely used except for
the case of vfork(). To prevent performance regressions of vfork(), we
skip taking oom_adj_mutex and setting MMF_MULTIPROCESS when CLONE_VFORK is
specified. Clearing the MMF_MULTIPROCESS flag (when the last process
sharing the mm exits) is left out of this patch to keep it simple and
because it is believed that this threading model is rare. Should there
ever be a need for optimizing that case as well, it can be done by hooking
into the exit path, likely following the mm_update_next_owner pattern.
With the combination of (CLONE_VM && !CLONE_THREAD && !CLONE_VFORK) being
quite rare, the regression is gone after the change is applied.
[surenb@google.com: v3]
Link: https://lkml.kernel.org/r/20200902012558.2335613-1-surenb@google.com
Fixes: 44a70adec910 ("mm, oom_adj: make sure processes sharing mm have same view of oom_score_adj")
Reported-by: Tim Murray <timmurray@google.com>
Suggested-by: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Eugene Syromiatnikov <esyr@redhat.com>
Cc: Christian Kellner <christian@kellner.me>
Cc: Adrian Reber <areber@redhat.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Aleksa Sarai <cyphar@cyphar.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alexey Gladkov <gladkov.alexey@gmail.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Andrei Vagin <avagin@gmail.com>
Cc: Bernd Edlinger <bernd.edlinger@hotmail.de>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Yafang Shao <laoar.shao@gmail.com>
Link: https://lkml.kernel.org/r/20200824153036.3201505-1-surenb@google.com
Debugged-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit baffd723e44dc3d7f84f0b8f1fe1ece00ddd2710 ]
The thinking in commit:
fddf9055a60d ("lockdep: Use raw_cpu_*() for per-cpu variables")
is flawed. While it is true that when we're migratable both CPUs will
have a 0 value, it doesn't hold that when we do get migrated in the
middle of a raw_cpu_op(), the old CPU will still have 0 by the time we
get around to reading it on the new CPU.
Luckily, the reason for that commit (s390 using preempt_disable()
instead of preempt_disable_notrace() in their percpu code), has since
been fixed by commit:
1196f12a2c96 ("s390: don't trace preemption in percpu macros")
An audit of arch/*/include/asm/percpu*.h shows there are no other
architectures affected by this particular issue.
Fixes: fddf9055a60d ("lockdep: Use raw_cpu_*() for per-cpu variables")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20201005095958.GJ2651@hirez.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4d004099a668c41522242aa146a38cc4eb59cb1e ]
Steve reported that lockdep_assert*irq*(), when nested inside lockdep
itself, will trigger a false-positive.
One example is the stack-trace code, as called from inside lockdep,
triggering tracing, which in turn calls RCU, which then uses
lockdep_assert_irqs_disabled().
Fixes: a21ee6055c30 ("lockdep: Change hardirq{s_enabled,_context} to per-cpu variables")
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2bb8945bcc1a768f2bc402a16c9610bba8d5187d ]
Basically print_lock_class_header()'s for loop is out of sync with the
the size of of ->usage_traces[].
Also clean things up a bit while at it, to avoid such mishaps in the future.
Fixes: 23870f122768 ("locking/lockdep: Fix "USED" <- "IN-NMI" inversions")
Reported-by: Qian Cai <cai@redhat.com>
Debugged-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Qian Cai <cai@redhat.com>
Link: https://lkml.kernel.org/r/20200930094937.GE2651@hirez.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 267580db047ef428a70bef8287ca62c5a450c139 ]
seqcount_LOCKNAME_init() needs to be a macro due to the lockdep
annotation in seqcount_init(). Since a macro cannot define another
macro, we need to effectively revert commit: e4e9ab3f9f91 ("seqlock:
Fold seqcount_LOCKNAME_init() definition").
Fixes: e4e9ab3f9f91 ("seqlock: Fold seqcount_LOCKNAME_init() definition")
Reported-by: Qian Cai <cai@redhat.com>
Debugged-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Qian Cai <cai@redhat.com>
Link: https://lkml.kernel.org/r/20200915143028.GB2674@hirez.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Merge misc fixes from Andrew Morton:
"Five fixes.
Subsystems affected by this patch series: MAINTAINERS, mm/pagemap,
mm/swap, and mm/hugetlb"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: khugepaged: recalculate min_free_kbytes after memory hotplug as expected by khugepaged
mm: validate inode in mapping_set_error()
mm: mmap: Fix general protection fault in unlink_file_vma()
MAINTAINERS: Antoine Tenart's email address
MAINTAINERS: change hardening mailing list
|
|
Pull vfs fix from Al Viro:
"Fixes an obvious bug (memory leak introduced in 5.8)"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
pipe: Fix memory leaks in create_pipe_files()
|
|
by khugepaged
When memory is hotplug added or removed the min_free_kbytes should be
recalculated based on what is expected by khugepaged. Currently after
hotplug, min_free_kbytes will be set to a lower default and higher
default set when THP enabled is lost.
This change restores min_free_kbytes as expected for THP consumers.
[vijayb@linux.microsoft.com: v5]
Link: https://lkml.kernel.org/r/1601398153-5517-1-git-send-email-vijayb@linux.microsoft.com
Fixes: f000565adb77 ("thp: set recommended min free kbytes")
Signed-off-by: Vijay Balakrishna <vijayb@linux.microsoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Allen Pais <apais@microsoft.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/1600305709-2319-2-git-send-email-vijayb@linux.microsoft.com
Link: https://lkml.kernel.org/r/1600204258-13683-1-git-send-email-vijayb@linux.microsoft.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The swap address_space doesn't have host. Thus, it makes kernel crash once
swap write meets error. Fix it.
Fixes: 735e4ae5ba28 ("vfs: track per-sb writeback errors and report them to syncfs")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Jeff Layton <jlayton@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Andres Freund <andres@anarazel.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20201010000650.750063-1-minchan@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull drm fixes from Dave Airlie:
"Daniel queued these up last week and I took a long weekend so didn't
get them out, but fixing the OOB access on get font seems like
something we should land and it's cc'ed stable as well.
The other big change is a partial revert for a regression on android
on the clcd fbdev driver, and one other docs fix.
fbdev:
- Re-add FB_ARMCLCD for android
- Fix global-out-of-bounds read in fbcon_get_font()
core:
- Small doc fix"
* tag 'drm-fixes-2020-10-06-1' of git://anongit.freedesktop.org/drm/drm:
drm: drm_dsc.h: fix a kernel-doc markup
Partially revert "video: fbdev: amba-clcd: Retire elder CLCD driver"
fbcon: Fix global-out-of-bounds read in fbcon_get_font()
Fonts: Support FONT_EXTRA_WORDS macros for built-in fonts
fbdev, newport_con: Move FONT_EXTRA_WORDS macros into linux/font.h
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v5.9:
- Small doc fix.
- Re-add FB_ARMCLCD for android.
- Fix global-out-of-bounds read in fbcon_get_font().
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8585daa2-fcbc-3924-ac4f-e7b5668808e0@linux.intel.com
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
"We have some fixes for Tablet Mode reporting in particular, that users
are complaining a lot about.
Summary:
- Attempt #3 of enabling Tablet Mode reporting w/o regressions
- Improve battery recognition code in ASUS WMI driver
- Fix Kconfig dependency warning for Fujitsu and LG laptop drivers
- Add fixes in Thinkpad ACPI driver for _BCL method and NVRAM polling
- Fix power supply extended topology in Mellanox driver
- Fix memory leak in OLPC EC driver
- Avoid static struct device in Intel PMC core driver
- Add support for the touchscreen found in MPMAN Converter9 2-in-1
- Update MAINTAINERS to reflect the real state of affairs"
* tag 'platform-drivers-x86-v5.9-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: thinkpad_acpi: re-initialize ACPI buffer size when reuse
MAINTAINERS: Add Mark Gross and Hans de Goede as x86 platform drivers maintainers
platform/x86: intel-vbtn: Switch to an allow-list for SW_TABLET_MODE reporting
platform/x86: intel-vbtn: Revert "Fix SW_TABLET_MODE always reporting 1 on the HP Pavilion 11 x360"
platform/x86: intel_pmc_core: do not create a static struct device
platform/x86: mlx-platform: Fix extended topology configuration for power supply units
platform/x86: pcengines-apuv2: Fix typo on define of AMD_FCH_GPIO_REG_GPIO55_DEVSLP0
platform/x86: fix kconfig dependency warning for FUJITSU_LAPTOP
platform/x86: fix kconfig dependency warning for LG_LAPTOP
platform/x86: thinkpad_acpi: initialize tp_nvram_state variable
platform/x86: intel-vbtn: Fix SW_TABLET_MODE always reporting 1 on the HP Pavilion 11 x360
platform/x86: asus-wmi: Add BATC battery name to the list of supported
platform/x86: asus-nb-wmi: Revert "Do not load on Asus T100TA and T200TA"
platform/x86: touchscreen_dmi: Add info for the MPMAN Converter9 2-in-1
Documentation: laptops: thinkpad-acpi: fix underline length build warning
Platform: OLPC: Fix memleak in olpc_ec_probe
|
|
Pull networking fixes from David Miller:
1) Make sure SKB control block is in the proper state during IPSEC
ESP-in-TCP encapsulation. From Sabrina Dubroca.
2) Various kinds of attributes were not being cloned properly when we
build new xfrm_state objects from existing ones. Fix from Antony
Antony.
3) Make sure to keep BTF sections, from Tony Ambardar.
4) TX DMA channels need proper locking in lantiq driver, from Hauke
Mehrtens.
5) Honour route MTU during forwarding, always. From Maciej
Żenczykowski.
6) Fix races in kTLS which can result in crashes, from Rohit
Maheshwari.
7) Skip TCP DSACKs with rediculous sequence ranges, from Priyaranjan
Jha.
8) Use correct address family in xfrm state lookups, from Herbert Xu.
9) A bridge FDB flush should not clear out user managed fdb entries
with the ext_learn flag set, from Nikolay Aleksandrov.
10) Fix nested locking of netdev address lists, from Taehee Yoo.
11) Fix handling of 32-bit DATA_FIN values in mptcp, from Mat Martineau.
12) Fix r8169 data corruptions on RTL8402 chips, from Heiner Kallweit.
13) Don't free command entries in mlx5 while comp handler could still be
running, from Eran Ben Elisha.
14) Error flow of request_irq() in mlx5 is busted, due to an off by one
we try to free and IRQ never allocated. From Maor Gottlieb.
15) Fix leak when dumping netlink policies, from Johannes Berg.
16) Sendpage cannot be performed when a page is a slab page, or the page
count is < 1. Some subsystems such as nvme were doing so. Create a
"sendpage_ok()" helper and use it as needed, from Coly Li.
17) Don't leak request socket when using syncookes with mptcp, from
Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
net/core: check length before updating Ethertype in skb_mpls_{push,pop}
net: mvneta: fix double free of txq->buf
net_sched: check error pointer in tcf_dump_walker()
net: team: fix memory leak in __team_options_register
net: typhoon: Fix a typo Typoon --> Typhoon
net: hinic: fix DEVLINK build errors
net: stmmac: Modify configuration method of EEE timers
tcp: fix syn cookied MPTCP request socket leak
libceph: use sendpage_ok() in ceph_tcp_sendpage()
scsi: libiscsi: use sendpage_ok() in iscsi_tcp_segment_map()
drbd: code cleanup by using sendpage_ok() to check page for kernel_sendpage()
tcp: use sendpage_ok() to detect misused .sendpage
nvme-tcp: check page by sendpage_ok() before calling kernel_sendpage()
net: add WARN_ONCE in kernel_sendpage() for improper zero-copy send
net: introduce helper sendpage_ok() in include/linux/net.h
net: usb: pegasus: Proper error handing when setting pegasus' MAC address
net: core: document two new elements of struct net_device
netlink: fix policy dump leak
net/mlx5e: Fix race condition on nhe->n pointer in neigh update
net/mlx5e: Fix VLAN create flow
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
From: Saeed Mahameed <saeedm@nvidia.com>
====================
This series introduces some fixes to mlx5 driver.
v1->v2:
- Patch #1 Don't return while mutex is held. (Dave)
v2->v3:
- Drop patch #1, will consider a better approach (Jakub)
- use cpu_relax() instead of cond_resched() (Jakub)
- while(i--) to reveres a loop (Jakub)
- Drop old mellanox email sign-off and change the committer email
(Jakub)
Please pull and let me know if there is any problem.
For -stable v4.15
('net/mlx5e: Fix VLAN cleanup flow')
('net/mlx5e: Fix VLAN create flow')
For -stable v4.16
('net/mlx5: Fix request_irqs error flow')
For -stable v5.4
('net/mlx5e: Add resiliency in Striding RQ mode for packets larger than MTU')
('net/mlx5: Avoid possible free of command entry while timeout comp handler')
For -stable v5.7
('net/mlx5e: Fix return status when setting unsupported FEC mode')
For -stable v5.8
('net/mlx5e: Fix race condition on nhe->n pointer in neigh update')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original problem was from nvme-over-tcp code, who mistakenly uses
kernel_sendpage() to send pages allocated by __get_free_pages() without
__GFP_COMP flag. Such pages don't have refcount (page_count is 0) on
tail pages, sending them by kernel_sendpage() may trigger a kernel panic
from a corrupted kernel heap, because these pages are incorrectly freed
in network stack as page_count 0 pages.
This patch introduces a helper sendpage_ok(), it returns true if the
checking page,
- is not slab page: PageSlab(page) is false.
- has page refcount: page_count(page) is not zero
All drivers who want to send page to remote end by kernel_sendpage()
may use this helper to check whether the page is OK. If the helper does
not return true, the driver should try other non sendpage method (e.g.
sock_no_sendpage()) to handle the page.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Vlastimil Babka <vbabka@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As warned by "make htmldocs", there are two new struct elements
that aren't documented:
../include/linux/netdevice.h:2159: warning: Function parameter or member 'unlink_list' not described in 'net_device'
../include/linux/netdevice.h:2159: warning: Function parameter or member 'nested_level' not described in 'net_device'
Fixes: 1fc70edb7d7b ("net: core: add nested_level variable in net_device")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of pci is offline reclaim_pages_cmd() will still try to call
the FW to release FW pages, cmd_exec() in this case will return a silent
success without actually calling the FW.
This is wrong and will cause page leaks, what we should do is to detect
pci offline or command interface un-available before tying to access the
FW and manually release the FW pages in the driver.
In this patch we share the code to check for FW command interface
availability and we call it in sensitive places e.g. reclaim_pages_cmd().
Alternative fix:
1. Remove MLX5_CMD_OP_MANAGE_PAGES form mlx5_internal_err_ret_value,
command success simulation list.
2. Always Release FW pages even if cmd_exec fails in reclaim_pages_cmd().
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Upon command completion timeout, driver simulates a forced command
completion. In a rare case where real interrupt for that command arrives
simultaneously, it might release the command entry while the forced
handler might still access it.
Fix that by adding an entry refcount, to track current amount of allowed
handlers. Command entry to be released only when this refcount is
decremented to zero.
Command refcount is always initialized to one. For callback commands,
command completion handler is the symmetric flow to decrement it. For
non-callback commands, it is wait_func().
Before ringing the doorbell, increment the refcount for the real completion
handler. Once the real completion handler is called, it will decrement it.
For callback commands, once the delayed work is scheduled, increment the
refcount. Upon callback command completion handler, we will try to cancel
the timeout callback. In case of success, we need to decrement the callback
refcount as it will never run.
In addition, gather the entry index free and the entry free into a one
flow for all command types release.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- Fix deadlock when removing MEMSTICK host
- Workaround broken CMDQ on Intel GLK based IRBIS models
* tag 'mmc-v5.9-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci: Workaround broken command queuing on Intel GLK based IRBIS models
memstick: Skip allocating card when removing host
|
|
Since commit ea426c2a7de8 ("mm: memcg: prepare for byte-sized vmstat
items") the write side of slab counters accepts a value in bytes and
converts it to pages. It happens in __mod_node_page_state().
However a non-SMP version of __mod_node_page_state() doesn't perform
this conversion. It leads to incorrect (unrealistically high) slab
counters values. Fix this by adding a similar conversion to the non-SMP
version of __mod_node_page_state().
Signed-off-by: Roman Gushchin <guro@fb.com>
Reported-and-tested-by: Bastian Bittorf <bb@npl.de>
Fixes: ea426c2a7de8 ("mm: memcg: prepare for byte-sized vmstat items")
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The pipe splice code still used the old model of waiting for pipe IO by
using a non-specific "pipe_wait()" that waited for any pipe event to
happen, which depended on all pipe IO being entirely serialized by the
pipe lock. So by checking the state you were waiting for, and then
adding yourself to the wait queue before dropping the lock, you were
guaranteed to see all the wakeups.
Strictly speaking, the actual wakeups were not done under the lock, but
the pipe_wait() model still worked, because since the waiter held the
lock when checking whether it should sleep, it would always see the
current state, and the wakeup was always done after updating the state.
However, commit 0ddad21d3e99 ("pipe: use exclusive waits when reading or
writing") split the single wait-queue into two, and in the process also
made the "wait for event" code wait for _two_ wait queues, and that then
showed a race with the wakers that were not serialized by the pipe lock.
It's only splice that used that "pipe_wait()" model, so the problem
wasn't obvious, but Josef Bacik reports:
"I hit a hang with fstest btrfs/187, which does a btrfs send into
/dev/null. This works by creating a pipe, the write side is given to
the kernel to write into, and the read side is handed to a thread that
splices into a file, in this case /dev/null.
The box that was hung had the write side stuck here [pipe_write] and
the read side stuck here [splice_from_pipe_next -> pipe_wait].
[ more details about pipe_wait() scenario ]
The problem is we're doing the prepare_to_wait, which sets our state
each time, however we can be woken up either with reads or writes. In
the case above we race with the WRITER waking us up, and re-set our
state to INTERRUPTIBLE, and thus never break out of schedule"
Josef had a patch that avoided the issue in pipe_wait() by just making
it set the state only once, but the deeper problem is that pipe_wait()
depends on a level of synchonization by the pipe mutex that it really
shouldn't. And the whole "wait for any pipe state change" model really
isn't very good to begin with.
So rather than trying to work around things in pipe_wait(), remove that
legacy model of "wait for arbitrary pipe event" entirely, and actually
create functions that wait for the pipe actually being readable or
writable, and can do so without depending on the pipe lock serializing
everything.
Fixes: 0ddad21d3e99 ("pipe: use exclusive waits when reading or writing")
Link: https://lore.kernel.org/linux-fsdevel/bfa88b5ad6f069b2b679316b9e495a970130416c.1601567868.git.josef@toxicpanda.com/
Reported-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-and-tested-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"A previous commit to prevent AML memory opregions from accessing the
kernel memory turned out to be too restrictive. Relax the permission
check to permit the ACPI core to map kernel memory used for table
overrides"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: permit ACPI core to map kernel memory used for table overrides
|
|
Calling pipe2() with O_NOTIFICATION_PIPE could results in memory
leaks unless watch_queue_init() is successful.
In case of watch_queue_init() failure in pipe2() we are left
with inode and pipe_inode_info instances that need to be freed. That
failure exit has been introduced in commit c73be61cede5 ("pipe: Add
general notification queue support") and its handling should've been
identical to nearby treatment of alloc_file_pseudo() failures - it
is dealing with the same situation. As it is, the mainline kernel
leaks in that case.
Another problem is that CONFIG_WATCH_QUEUE and !CONFIG_WATCH_QUEUE
cases are treated differently (and the former leaks just pipe_inode_info,
the latter - both pipe_inode_info and inode).
Fixed by providing a dummy wacth_queue_init() in !CONFIG_WATCH_QUEUE
case and by having failures of wacth_queue_init() handled the same way
we handle alloc_file_pseudo() ones.
Fixes: c73be61cede5 ("pipe: Add general notification queue support")
Signed-off-by: Qian Cai <cai@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Jonathan reports that the strict policy for memory mapped by the
ACPI core breaks the use case of passing ACPI table overrides via
initramfs. This is due to the fact that the memory type used for
loading the initramfs in memory is not recognized as a memory type
that is typically used by firmware to pass firmware tables.
Since the purpose of the strict policy is to ensure that no AML or
other ACPI code can manipulate any memory that is used by the kernel
to keep its internal state or the state of user tasks, we can relax
the permission check, and allow mappings of memory that is reserved
and marked as NOMAP via memblock, and therefore not covered by the
linear mapping to begin with.
Fixes: 1583052d111f ("arm64/acpi: disallow AML memory opregions to access kernel memory")
Fixes: 325f5585ec36 ("arm64/acpi: disallow writeable AML opregion mapping for EFI code regions")
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20200929132522.18067-1-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Also partially revert the follow-up change "drm: pl111: Absorb the
external register header".
This reverts the parts of commits
7e4e589db76a3cf4c1f534eb5a09cc6422766b93 and
0fb8125635e8eb5483fb095f98dcf0651206a7b8 that touch paths outside
of drivers/gpu/drm/pl111.
The fbdev driver is used by Android's FVP configuration. Using the
DRM driver together with DRM's fbdev emulation results in a failure
to boot Android. The root cause is that Android's generic fbdev
userspace driver relies on the ability to set the pixel format via
FBIOPUT_VSCREENINFO, which is not supported by fbdev emulation.
There have been other less critical behavioral differences identified
between the fbdev driver and the DRM driver with fbdev emulation. The
DRM driver exposes different values for the panel's width, height and
refresh rate, and the DRM driver fails a FBIOPUT_VSCREENINFO syscall
with yres_virtual greater than the maximum supported value instead
of letting the syscall succeed and setting yres_virtual based on yres.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929195344.2219796-1-pcc@google.com
|
|
This patch is to add a new variable 'nested_level' into the net_device
structure.
This variable will be used as a parameter of spin_lock_nested() of
dev->addr_list_lock.
netif_addr_lock() can be called recursively so spin_lock_nested() is
used instead of spin_lock() and dev->lower_level is used as a parameter
of spin_lock_nested().
But, dev->lower_level value can be updated while it is being used.
So, lockdep would warn a possible deadlock scenario.
When a stacked interface is deleted, netif_{uc | mc}_sync() is
called recursively.
So, spin_lock_nested() is called recursively too.
At this moment, the dev->lower_level variable is used as a parameter of it.
dev->lower_level value is updated when interfaces are being unlinked/linked
immediately.
Thus, After unlinking, dev->lower_level shouldn't be a parameter of
spin_lock_nested().
A (macvlan)
|
B (vlan)
|
C (bridge)
|
D (macvlan)
|
E (vlan)
|
F (bridge)
A->lower_level : 6
B->lower_level : 5
C->lower_level : 4
D->lower_level : 3
E->lower_level : 2
F->lower_level : 1
When an interface 'A' is removed, it releases resources.
At this moment, netif_addr_lock() would be called.
Then, netdev_upper_dev_unlink() is called recursively.
Then dev->lower_level is updated.
There is no problem.
But, when the bridge module is removed, 'C' and 'F' interfaces
are removed at once.
If 'F' is removed first, a lower_level value is like below.
A->lower_level : 5
B->lower_level : 4
C->lower_level : 3
D->lower_level : 2
E->lower_level : 1
F->lower_level : 1
Then, 'C' is removed. at this moment, netif_addr_lock() is called
recursively.
The ordering is like this.
C(3)->D(2)->E(1)->F(1)
At this moment, the lower_level value of 'E' and 'F' are the same.
So, lockdep warns a possible deadlock scenario.
In order to avoid this problem, a new variable 'nested_level' is added.
This value is the same as dev->lower_level - 1.
But this value is updated in rtnl_unlock().
So, this variable can be used as a parameter of spin_lock_nested() safely
in the rtnl context.
Test commands:
ip link add br0 type bridge vlan_filtering 1
ip link add vlan1 link br0 type vlan id 10
ip link add macvlan2 link vlan1 type macvlan
ip link add br3 type bridge vlan_filtering 1
ip link set macvlan2 master br3
ip link add vlan4 link br3 type vlan id 10
ip link add macvlan5 link vlan4 type macvlan
ip link add br6 type bridge vlan_filtering 1
ip link set macvlan5 master br6
ip link add vlan7 link br6 type vlan id 10
ip link add macvlan8 link vlan7 type macvlan
ip link set br0 up
ip link set vlan1 up
ip link set macvlan2 up
ip link set br3 up
ip link set vlan4 up
ip link set macvlan5 up
ip link set br6 up
ip link set vlan7 up
ip link set macvlan8 up
modprobe -rv bridge
Splat looks like:
[ 36.057436][ T744] WARNING: possible recursive locking detected
[ 36.058848][ T744] 5.9.0-rc6+ #728 Not tainted
[ 36.059959][ T744] --------------------------------------------
[ 36.061391][ T744] ip/744 is trying to acquire lock:
[ 36.062590][ T744] ffff8c4767509280 (&vlan_netdev_addr_lock_key){+...}-{2:2}, at: dev_set_rx_mode+0x19/0x30
[ 36.064922][ T744]
[ 36.064922][ T744] but task is already holding lock:
[ 36.066626][ T744] ffff8c4767769280 (&vlan_netdev_addr_lock_key){+...}-{2:2}, at: dev_uc_add+0x1e/0x60
[ 36.068851][ T744]
[ 36.068851][ T744] other info that might help us debug this:
[ 36.070731][ T744] Possible unsafe locking scenario:
[ 36.070731][ T744]
[ 36.072497][ T744] CPU0
[ 36.073238][ T744] ----
[ 36.074007][ T744] lock(&vlan_netdev_addr_lock_key);
[ 36.075290][ T744] lock(&vlan_netdev_addr_lock_key);
[ 36.076590][ T744]
[ 36.076590][ T744] *** DEADLOCK ***
[ 36.076590][ T744]
[ 36.078515][ T744] May be due to missing lock nesting notation
[ 36.078515][ T744]
[ 36.080491][ T744] 3 locks held by ip/744:
[ 36.081471][ T744] #0: ffffffff98571df0 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x236/0x490
[ 36.083614][ T744] #1: ffff8c4767769280 (&vlan_netdev_addr_lock_key){+...}-{2:2}, at: dev_uc_add+0x1e/0x60
[ 36.085942][ T744] #2: ffff8c476c8da280 (&bridge_netdev_addr_lock_key/4){+...}-{2:2}, at: dev_uc_sync+0x39/0x80
[ 36.088400][ T744]
[ 36.088400][ T744] stack backtrace:
[ 36.089772][ T744] CPU: 6 PID: 744 Comm: ip Not tainted 5.9.0-rc6+ #728
[ 36.091364][ T744] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 36.093630][ T744] Call Trace:
[ 36.094416][ T744] dump_stack+0x77/0x9b
[ 36.095385][ T744] __lock_acquire+0xbc3/0x1f40
[ 36.096522][ T744] lock_acquire+0xb4/0x3b0
[ 36.097540][ T744] ? dev_set_rx_mode+0x19/0x30
[ 36.098657][ T744] ? rtmsg_ifinfo+0x1f/0x30
[ 36.099711][ T744] ? __dev_notify_flags+0xa5/0xf0
[ 36.100874][ T744] ? rtnl_is_locked+0x11/0x20
[ 36.101967][ T744] ? __dev_set_promiscuity+0x7b/0x1a0
[ 36.103230][ T744] _raw_spin_lock_bh+0x38/0x70
[ 36.104348][ T744] ? dev_set_rx_mode+0x19/0x30
[ 36.105461][ T744] dev_set_rx_mode+0x19/0x30
[ 36.106532][ T744] dev_set_promiscuity+0x36/0x50
[ 36.107692][ T744] __dev_set_promiscuity+0x123/0x1a0
[ 36.108929][ T744] dev_set_promiscuity+0x1e/0x50
[ 36.110093][ T744] br_port_set_promisc+0x1f/0x40 [bridge]
[ 36.111415][ T744] br_manage_promisc+0x8b/0xe0 [bridge]
[ 36.112728][ T744] __dev_set_promiscuity+0x123/0x1a0
[ 36.113967][ T744] ? __hw_addr_sync_one+0x23/0x50
[ 36.115135][ T744] __dev_set_rx_mode+0x68/0x90
[ 36.116249][ T744] dev_uc_sync+0x70/0x80
[ 36.117244][ T744] dev_uc_add+0x50/0x60
[ 36.118223][ T744] macvlan_open+0x18e/0x1f0 [macvlan]
[ 36.119470][ T744] __dev_open+0xd6/0x170
[ 36.120470][ T744] __dev_change_flags+0x181/0x1d0
[ 36.121644][ T744] dev_change_flags+0x23/0x60
[ 36.122741][ T744] do_setlink+0x30a/0x11e0
[ 36.123778][ T744] ? __lock_acquire+0x92c/0x1f40
[ 36.124929][ T744] ? __nla_validate_parse.part.6+0x45/0x8e0
[ 36.126309][ T744] ? __lock_acquire+0x92c/0x1f40
[ 36.127457][ T744] __rtnl_newlink+0x546/0x8e0
[ 36.128560][ T744] ? lock_acquire+0xb4/0x3b0
[ 36.129623][ T744] ? deactivate_slab.isra.85+0x6a1/0x850
[ 36.130946][ T744] ? __lock_acquire+0x92c/0x1f40
[ 36.132102][ T744] ? lock_acquire+0xb4/0x3b0
[ 36.133176][ T744] ? is_bpf_text_address+0x5/0xe0
[ 36.134364][ T744] ? rtnl_newlink+0x2e/0x70
[ 36.135445][ T744] ? rcu_read_lock_sched_held+0x32/0x60
[ 36.136771][ T744] ? kmem_cache_alloc_trace+0x2d8/0x380
[ 36.138070][ T744] ? rtnl_newlink+0x2e/0x70
[ 36.139164][ T744] rtnl_newlink+0x47/0x70
[ ... ]
Fixes: 845e0ebb4408 ("net: change addr_list_lock back to static key")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
infrastructure
Functions related to nested interface infrastructure such as
netdev_walk_all_{ upper | lower }_dev() pass both private functions
and "data" pointer to handle their own things.
At this point, the data pointer type is void *.
In order to make it easier to expand common variables and functions,
this new netdev_nested_priv structure is added.
In the following patch, a new member variable will be added into this
struct to fix the lockdep issue.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- NFSv4.2: copy_file_range needs to invalidate caches on success
- NFSv4.2: Fix security label length not being reset
- pNFS/flexfiles: Ensure we initialise the mirror bsizes correctly
on read
- pNFS/flexfiles: Fix signed/unsigned type issues with mirror
indices"
* tag 'nfs-for-5.9-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
pNFS/flexfiles: Be consistent about mirror index types
pNFS/flexfiles: Ensure we initialise the mirror bsizes correctly on read
NFSv4.2: fix client's attribute cache management for copy_file_range
nfs: Fix security label length not being reset
|
|
After commit 6827ca573c03 ("memstick: rtsx_usb_ms: Support runtime power
management"), removing module rtsx_usb_ms will be stuck.
The deadlock is caused by powering on and powering off at the same time,
the former one is when memstick_check() is flushed, and the later is called
by memstick_remove_host().
Soe let's skip allocating card to prevent this issue.
Fixes: 6827ca573c03 ("memstick: rtsx_usb_ms: Support runtime power management")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20200925084952.13220-1-kai.heng.feng@canonical.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This prepares for the future work to trigger early cow on pinned pages
during fork().
No functional change intended.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
(Commit message majorly collected from Jason Gunthorpe)
Reduce the chance of false positive from page_maybe_dma_pinned() by
keeping track if the mm_struct has ever been used with pin_user_pages().
This allows cases that might drive up the page ref_count to avoid any
penalty from handling dma_pinned pages.
Future work is planned, to provide a more sophisticated solution, likely
to turn it into a real counter. For now, make it atomic_t but use it as
a boolean for simplicity.
Suggested-by: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three fixes: one in drivers (lpfc) and two for zoned block devices.
The latter also impinges on the block layer but only to introduce a
new block API for setting the zone model rather than fiddling with the
queue directly in the zoned block driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: sd_zbc: Fix ZBC disk initialization
scsi: sd: sd_zbc: Fix handling of host-aware ZBC disks
scsi: lpfc: Fix initial FLOGI failure due to BBSCN not supported
|
|
Pull block fixes from Jens Axboe:
"NVMe pull request from Christoph, and removal of a dead define.
- fix error during controller probe that cause double free irqs
(Keith Busch)
- FC connection establishment fix (James Smart)
- properly handle completions for invalid tags (Xianting Tian)
- pass the correct nsid to the command effects and supported log
(Chaitanya Kulkarni)"
* tag 'block-5.9-2020-09-25' of git://git.kernel.dk/linux-block:
block: remove unused BLK_QC_T_EAGAIN flag
nvme-core: don't use NVME_NSID_ALL for command effects and supported log
nvme-fc: fail new connections to a deleted host or remote port
nvme-pci: fix NULL req in completion handler
nvme: return errors for hwmon init
|
|
In register_mem_sect_under_node() the system_state's value is checked to
detect whether the call is made during boot time or during an hot-plug
operation. Unfortunately, that check against SYSTEM_BOOTING is wrong
because regular memory is registered at SYSTEM_SCHEDULING state. In
addition, memory hot-plug operation can be triggered at this system
state by the ACPI [1]. So checking against the system state is not
enough.
The consequence is that on system with interleaved node's ranges like this:
Early memory node ranges
node 1: [mem 0x0000000000000000-0x000000011fffffff]
node 2: [mem 0x0000000120000000-0x000000014fffffff]
node 1: [mem 0x0000000150000000-0x00000001ffffffff]
node 0: [mem 0x0000000200000000-0x000000048fffffff]
node 2: [mem 0x0000000490000000-0x00000007ffffffff]
This can be seen on PowerPC LPAR after multiple memory hot-plug and
hot-unplug operations are done. At the next reboot the node's memory
ranges can be interleaved and since the call to link_mem_sections() is
made in topology_init() while the system is in the SYSTEM_SCHEDULING
state, the node's id is not checked, and the sections registered to
multiple nodes:
$ ls -l /sys/devices/system/memory/memory21/node*
total 0
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node1 -> ../../node/node1
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node2 -> ../../node/node2
In that case, the system is able to boot but if later one of theses
memory blocks is hot-unplugged and then hot-plugged, the sysfs
inconsistency is detected and this is triggering a BUG_ON():
kernel BUG at /Users/laurent/src/linux-ppc/mm/memory_hotplug.c:1084!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: rpadlpar_io rpaphp pseries_rng rng_core vmx_crypto gf128mul binfmt_misc ip_tables x_tables xfs libcrc32c crc32c_vpmsum autofs4
CPU: 8 PID: 10256 Comm: drmgr Not tainted 5.9.0-rc1+ #25
Call Trace:
add_memory_resource+0x23c/0x340 (unreliable)
__add_memory+0x5c/0xf0
dlpar_add_lmb+0x1b4/0x500
dlpar_memory+0x1f8/0xb80
handle_dlpar_errorlog+0xc0/0x190
dlpar_store+0x198/0x4a0
kobj_attr_store+0x30/0x50
sysfs_kf_write+0x64/0x90
kernfs_fop_write+0x1b0/0x290
vfs_write+0xe8/0x290
ksys_write+0xdc/0x130
system_call_exception+0x160/0x270
system_call_common+0xf0/0x27c
This patch addresses the root cause by not relying on the system_state
value to detect whether the call is due to a hot-plug operation. An
extra parameter is added to link_mem_sections() detailing whether the
operation is due to a hot-plug operation.
[1] According to Oscar Salvador, using this qemu command line, ACPI
memory hotplug operations are raised at SYSTEM_SCHEDULING state:
$QEMU -enable-kvm -machine pc -smp 4,sockets=4,cores=1,threads=1 -cpu host -monitor pty \
-m size=$MEM,slots=255,maxmem=4294967296k \
-numa node,nodeid=0,cpus=0-3,mem=512 -numa node,nodeid=1,mem=512 \
-object memory-backend-ram,id=memdimm0,size=134217728 -device pc-dimm,node=0,memdev=memdimm0,id=dimm0,slot=0 \
-object memory-backend-ram,id=memdimm1,size=134217728 -device pc-dimm,node=0,memdev=memdimm1,id=dimm1,slot=1 \
-object memory-backend-ram,id=memdimm2,size=134217728 -device pc-dimm,node=0,memdev=memdimm2,id=dimm2,slot=2 \
-object memory-backend-ram,id=memdimm3,size=134217728 -device pc-dimm,node=0,memdev=memdimm3,id=dimm3,slot=3 \
-object memory-backend-ram,id=memdimm4,size=134217728 -device pc-dimm,node=1,memdev=memdimm4,id=dimm4,slot=4 \
-object memory-backend-ram,id=memdimm5,size=134217728 -device pc-dimm,node=1,memdev=memdimm5,id=dimm5,slot=5 \
-object memory-backend-ram,id=memdimm6,size=134217728 -device pc-dimm,node=1,memdev=memdimm6,id=dimm6,slot=6 \
Fixes: 4fbce633910e ("mm/memory_hotplug.c: make register_mem_sect_under_node() a callback of walk_memory_range()")
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Cc: Scott Cheloha <cheloha@linux.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200915094143.79181-3-ldufour@linux.ibm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "mm: fix memory to node bad links in sysfs", v3.
Sometimes, firmware may expose interleaved memory layout like this:
Early memory node ranges
node 1: [mem 0x0000000000000000-0x000000011fffffff]
node 2: [mem 0x0000000120000000-0x000000014fffffff]
node 1: [mem 0x0000000150000000-0x00000001ffffffff]
node 0: [mem 0x0000000200000000-0x000000048fffffff]
node 2: [mem 0x0000000490000000-0x00000007ffffffff]
In that case, we can see memory blocks assigned to multiple nodes in
sysfs:
$ ls -l /sys/devices/system/memory/memory21
total 0
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node1 -> ../../node/node1
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node2 -> ../../node/node2
-rw-r--r-- 1 root root 65536 Aug 24 05:27 online
-r--r--r-- 1 root root 65536 Aug 24 05:27 phys_device
-r--r--r-- 1 root root 65536 Aug 24 05:27 phys_index
drwxr-xr-x 2 root root 0 Aug 24 05:27 power
-r--r--r-- 1 root root 65536 Aug 24 05:27 removable
-rw-r--r-- 1 root root 65536 Aug 24 05:27 state
lrwxrwxrwx 1 root root 0 Aug 24 05:25 subsystem -> ../../../../bus/memory
-rw-r--r-- 1 root root 65536 Aug 24 05:25 uevent
-r--r--r-- 1 root root 65536 Aug 24 05:27 valid_zones
The same applies in the node's directory with a memory21 link in both
the node1 and node2's directory.
This is wrong but doesn't prevent the system to run. However when
later, one of these memory blocks is hot-unplugged and then hot-plugged,
the system is detecting an inconsistency in the sysfs layout and a
BUG_ON() is raised:
kernel BUG at /Users/laurent/src/linux-ppc/mm/memory_hotplug.c:1084!
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: rpadlpar_io rpaphp pseries_rng rng_core vmx_crypto gf128mul binfmt_misc ip_tables x_tables xfs libcrc32c crc32c_vpmsum autofs4
CPU: 8 PID: 10256 Comm: drmgr Not tainted 5.9.0-rc1+ #25
Call Trace:
add_memory_resource+0x23c/0x340 (unreliable)
__add_memory+0x5c/0xf0
dlpar_add_lmb+0x1b4/0x500
dlpar_memory+0x1f8/0xb80
handle_dlpar_errorlog+0xc0/0x190
dlpar_store+0x198/0x4a0
kobj_attr_store+0x30/0x50
sysfs_kf_write+0x64/0x90
kernfs_fop_write+0x1b0/0x290
vfs_write+0xe8/0x290
ksys_write+0xdc/0x130
system_call_exception+0x160/0x270
system_call_common+0xf0/0x27c
This has been seen on PowerPC LPAR.
The root cause of this issue is that when node's memory is registered,
the range used can overlap another node's range, thus the memory block
is registered to multiple nodes in sysfs.
There are two issues here:
(a) The sysfs memory and node's layouts are broken due to these
multiple links
(b) The link errors in link_mem_sections() should not lead to a system
panic.
To address (a) register_mem_sect_under_node should not rely on the
system state to detect whether the link operation is triggered by a hot
plug operation or not. This is addressed by the patches 1 and 2 of this
series.
Issue (b) will be addressed separately.
This patch (of 2):
The memmap_context enum is used to detect whether a memory operation is
due to a hot-add operation or happening at boot time.
Make it general to the hotplug operation and rename it as
meminit_context.
There is no functional change introduced by this patch
Suggested-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J . Wysocki" <rafael@kernel.org>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Cc: Scott Cheloha <cheloha@linux.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200915094143.79181-1-ldufour@linux.ibm.com
Link: https://lkml.kernel.org/r/20200915132624.9723-1-ldufour@linux.ibm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently to make sure that every page table entry is read just once
gup_fast walks perform READ_ONCE and pass pXd value down to the next
gup_pXd_range function by value e.g.:
static int gup_pud_range(p4d_t p4d, unsigned long addr, unsigned long end,
unsigned int flags, struct page **pages, int *nr)
...
pudp = pud_offset(&p4d, addr);
This function passes a reference on that local value copy to pXd_offset,
and might get the very same pointer in return. This happens when the
level is folded (on most arches), and that pointer should not be
iterated.
On s390 due to the fact that each task might have different 5,4 or
3-level address translation and hence different levels folded the logic
is more complex and non-iteratable pointer to a local copy leads to
severe problems.
Here is an example of what happens with gup_fast on s390, for a task
with 3-level paging, crossing a 2 GB pud boundary:
// addr = 0x1007ffff000, end = 0x10080001000
static int gup_pud_range(p4d_t p4d, unsigned long addr, unsigned long end,
unsigned int flags, struct page **pages, int *nr)
{
unsigned long next;
pud_t *pudp;
// pud_offset returns &p4d itself (a pointer to a value on stack)
pudp = pud_offset(&p4d, addr);
do {
// on second iteratation reading "random" stack value
pud_t pud = READ_ONCE(*pudp);
// next = 0x10080000000, due to PUD_SIZE/MASK != PGDIR_SIZE/MASK on s390
next = pud_addr_end(addr, end);
...
} while (pudp++, addr = next, addr != end); // pudp++ iterating over stack
return 1;
}
This happens since s390 moved to common gup code with commit
d1874a0c2805 ("s390/mm: make the pxd_offset functions more robust") and
commit 1a42010cdc26 ("s390/mm: convert to the generic
get_user_pages_fast code").
s390 tried to mimic static level folding by changing pXd_offset
primitives to always calculate top level page table offset in pgd_offset
and just return the value passed when pXd_offset has to act as folded.
What is crucial for gup_fast and what has been overlooked is that
PxD_SIZE/MASK and thus pXd_addr_end should also change correspondingly.
And the latter is not possible with dynamic folding.
To fix the issue in addition to pXd values pass original pXdp pointers
down to gup_pXd_range functions. And introduce pXd_offset_lockless
helpers, which take an additional pXd entry value parameter. This has
already been discussed in
https://lkml.kernel.org/r/20190418100218.0a4afd51@mschwideX1
Fixes: 1a42010cdc26 ("s390/mm: convert to the generic get_user_pages_fast code")
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Claudio Imbrenda <imbrenda@linux.ibm.com>
Cc: <stable@vger.kernel.org> [5.2+]
Link: https://lkml.kernel.org/r/patch.git-943f1e5dcff2.your-ad-here.call-01599856292-ext-8676@work.hours
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 7b6620d7db56 ("block: remove REQ_NOWAIT_INLINE") removed the
REQ_NOWAIT_INLINE related code, but the diff wasn't applied to
blk_types.h somehow.
Then commit 2771cefeac49 ("block: remove the REQ_NOWAIT_INLINE flag")
removed the REQ_NOWAIT_INLINE flag while the BLK_QC_T_EAGAIN flag still
remains.
Fixes: 7b6620d7db56 ("block: remove REQ_NOWAIT_INLINE")
Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
syzbot has reported an issue in the framebuffer layer, where a malicious
user may overflow our built-in font data buffers.
In order to perform a reliable range check, subsystems need to know
`FONTDATAMAX` for each built-in font. Unfortunately, our font descriptor,
`struct console_font` does not contain `FONTDATAMAX`, and is part of the
UAPI, making it infeasible to modify it.
For user-provided fonts, the framebuffer layer resolves this issue by
reserving four extra words at the beginning of data buffers. Later,
whenever a function needs to access them, it simply uses the following
macros:
Recently we have gathered all the above macros to <linux/font.h>. Let us
do the same thing for built-in fonts, prepend four extra words (including
`FONTDATAMAX`) to their data buffers, so that subsystems can use these
macros for all fonts, no matter built-in or user-provided.
This patch depends on patch "fbdev, newport_con: Move FONT_EXTRA_WORDS
macros into linux/font.h".
Cc: stable@vger.kernel.org
Link: https://syzkaller.appspot.com/bug?id=08b8be45afea11888776f897895aef9ad1c3ecfd
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/ef18af00c35fb3cc826048a5f70924ed6ddce95b.1600953813.git.yepeilin.cs@gmail.com
|
|
drivers/video/console/newport_con.c is borrowing FONT_EXTRA_WORDS macros
from drivers/video/fbdev/core/fbcon.h. To keep things simple, move all
definitions into <linux/font.h>.
Since newport_con now uses four extra words, initialize the fourth word in
newport_set_font() properly.
Cc: stable@vger.kernel.org
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/7fb8bc9b0abc676ada6b7ac0e0bd443499357267.1600953813.git.yepeilin.cs@gmail.com
|
|
AMD_FCH_GPIO_REG_GPIO55_DEVSLP0
Schematics show that the GPIO number is 55 (not 59). Trivial typo.
Signed-off-by: Ed Wildgoose <lists@wildgooses.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
