| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
9d265124d051 and 15a260d53f7c added quirks for P2P bridges that support
I/O windows that start/end at 1K boundaries, not just the 4K boundaries
defined by the PCI spec. For details, see the IOBL_ADR register and the
EN1K bit in the CNF register in the Intel 82870P2 (P64H2).
These quirks complicate the code that reads P2P bridge windows
(pci_read_bridge_io() and pci_cfg_fake_ranges()) because the bridge
I/O resource is updated in the HEADER quirk, in pci_read_bridge_io(),
in pci_setup_bridge(), and again in the FINAL quirk. This is confusing
and makes it impossible to reassign the bridge windows after FINAL
quirks are run.
This patch adds support for 1K windows in the generic paths, so the
HEADER quirk only has to enable this support. The FINAL quirk, which
used to undo damage done by pci_setup_bridge(), is no longer needed.
This removes "if (!res->start) res->start = ..." from pci_read_bridge_io();
that was part of 9d265124d051 to avoid overwriting the resource filled in
by the quirk. Since pci_read_bridge_io() itself now knows about
granularity, the quirk no longer updates the resource and this test is no
longer needed.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Some devices (e.g. Sony's PaSoRi) can not do type B polling, so we have
to make a distinction between ISO14443 type A and B poll modes.
Cc: Eric Lapuyade <eric.lapuyade@intel.com>
Cc: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This function is needed by brcmsmac. This code is based on code from
the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This code is based on the Broadcom SDK and brcmsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The chip IDs are used all over bcma and no constants where defined.
This patch adds the constants and makes bcma use them.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch is based on a recent version of the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/rpmsg
Pull rpmsg fixes from Ohad Ben-Cohen:
"Fixing two (somewhat rare) endpoint-related race issues, both of which
were reported by Fernando Guzman Lugo."
* tag 'rpmsg-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/rpmsg:
rpmsg: make sure inflight messages don't invoke just-removed callbacks
rpmsg: avoid premature deallocation of endpoints
|
|
Add a helper function for validating a scan mask for devices where exactly one
channel must be selected during sampling. This is a common case among devices
which have scan mask restrictions so it makes sense to provide this function in
the core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This is useful for cases where the number of valid scan masks grows
exponentially, but it is rather easy to check whether a mask is valid or not
programmatically.
An example of such a case is a device with multiple ADCs where each ADC has a
upstream MUX, which allows to select from a number of physical channels.
+-------+ +-------+
| | | | --- Channel 1
| ADC 1 |---| MUX 1 | --- ...
| | | | --- Channel M
+-------+ +-------+
. . .
. . .
. . .
+-------+ +-------+
| | | | --- Channel M * N + 1
| ADC N |---| MUX N | --- ...
| | | | --- Channel M * N + M
+-------+ +-------+
The number of necessary scan masks for this case is (M+1)**N - 1, on the other
hand it is easy to check whether subsets for each ADC of the scanmask have only
one bit set.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Sometimes, the driver bindings may know what phy they use.
For example, when using device tree, the usb controller may have a
phandler pointing to usb phy.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This let usb phy driver has a chance to change hw settings when connect
status change.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Platform drivers do the similar things to add/remove ci13xxx device, so
create a unified one.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
struct ci13xxx represent the controller, which may be device or host,
so name its variables as ci.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The keys are found on the keyboards bundled with HP All-In-One machines
with USB VID/PID of 04ca:004d and 04f2:1061.
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Remove the clocks from the list of regulators to correct the value of
MAX77686_REG_MAX which is used in the regulator driver to represent the no.
of regulators present in max77686.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
in hw design, 800 is mainly for pmic control, while 805 for audio.
but there are 3 registers which controls class D speaker property,
and they are defined in 800 i2c client domain. so 805 codec driver
needs to use 800 i2c client to access class D speaker reg for
audio path management. so add this workaround for the purpose to
let 805 access 800 i2c in some scenario.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
88PM800 and 88PM805 are two discrete chips used for power management.
Hardware designer can use them together or only one of them according
to requirement.
88pm80x.c provides common i2c driver handling for both 800 and
805, such as i2c_driver init, regmap init, read/write api etc.
88pm800.c handles specifically for 800, such as chip init, irq
init/handle, mfd device register, including rtc, onkey, regulator(
to be add later) etc. besides that, 800 has three i2c device, one
regular i2c client, two other i2c dummy for gpadc and power purpose.
88pm805.c handles specifically for 805, such as chip init, irq
init/handle, mfd device register, including codec, headset/mic detect
etc.
the i2c operation of both 800 and 805 are via regmap, and 88pm80x-i2c
exported a group of r/w bulk r/w and bits set API for facility.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to support a P2P device abstraction and
Bluetooth high-speed AMPs, we need to have a way
to identify virtual interfaces that don't have a
netdev associated.
Do this by adding a NL80211_ATTR_WDEV attribute
to identify a wdev which may or may not also be
a netdev.
To simplify things, use a 64-bit value with the
high 32 bits being the wiphy index for this new
wdev identifier in the nl80211 API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The header and driver are only used by arm/mach-u8500 (and potentially
arm/mach-nomadik), but the STA2X11 I/O Hub exports on PCIe a number of
devices, including i2c-nomadik. This patch allows compilation of the
driver under x86.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
All allocators have some sort of support for the bootstrap status.
Setup a common definition for the boot states and make all slab
allocators use that definition.
Reviewed-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
|
|
Kmem_cache_create() does a variety of sanity checks but those
vary depending on the allocator. Use the strictest tests and put them into
a slab_common file. Make the tests conditional on CONFIG_DEBUG_VM.
This patch has the effect of adding sanity checks for SLUB and SLOB
under CONFIG_DEBUG_VM and removes the checks in SLAB for !CONFIG_DEBUG_VM.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
|
|
If registering of one of them fails, all already registered drivers
of this module will be unregistered.
Use the new register/unregister functions in all drivers
registering more than one driver.
amd.c, realtek.c: Simplify: directly return registration result.
Tested with broadcom.c
All others compile-tested.
Signed-off-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, VFs have 0 in their dev->caps.function field. This is a
valid pci id (usually of the PF). Instead, pass an invalid PCI id to
the VF via QUERY_FW, so that if the value gets accessed in the VF
driver, we'll catch the problem.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
These registers will be used in future devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Rather than open coding the enable GPIO control in the MFD core use the
API to push the management on to the regulator driver. The immediate
advantage is slight for most systems but this will in future allow device
configurations where an external regulator is used for DCVDD.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into for-next
mfd: Initial support for Wolfson Arizona platform and WM5102 devices
The Wolfson Arizona platform is used to provide common register
interface to a series of low power audio hub CODECs, starting with the
WM5102. Since the features of these devices work over a range of
subsystems an MFD core driver is provided to instantiate the subdevices
and arbitrate access between them.
As the new regmap wake IRQ functionality is used as part of the driver
it is incorporated as a dependency.
|
|
Now this driver is using regmap API, the iolock mutex is not used and
can be removed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Pre-regulator of 88pm8606 is mainly for support charging based on vbus,
it needs to be enabled for charging battery, and will be disabled in
some exception condition like over-temp.
Add the pre-regulator device init data and resource for mfd subdev.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add flag to platform data to enable external 32-kHz crystal oscillator
(or square wave) input.
The tps6591x can use either an internal 32-kHz RC oscillator or an
external crystal (or square wave) to generate the 32-kHz clock.
The default setting depends on the selected boot mode. In boot mode 00
the internal RC oscillator is used at power-on, but the external crystal
oscillator (or square wave) can be enabled by clearing the ck32k_ctrl
flag in the device control register.
Note that there is no way to switch from the external crystal oscillator
to the internal RC oscillator.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add irq domain support for max8997 interrupts. The reverse mapping method
used is linear mapping since the sub-drivers of max8997 such as regulator
and charger drivers can use the max8997 irq_domain to get the linux irq
number for max8997 interrupts. All uses of irq_base in platform data and
max8997 driver private data are removed.
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Applying a succinct description to the of_compatible variable recently
added to the mfd_cell struct. Also link to the documentation page where
more information can be found about compatible properties.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Force the Modem wakeup by asserting the CaWakeReq signal before the
hostaccess_req/ack ping-pong sequence. The Awake_req signal is de-asserted
asserted at the same time than the hostaccess_req. Return error on failure
case so that the client using this can take appropiate steps.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Since none of the users now reference the cache directly we can happily
remove the custom cache code and rely on the regmap cache.
For simplicity we don't bother with the register defaults tables but
instead read the defaults from the device - regmap is capable of doing
this, unlike our old cache infrastructure. This saves a lot of code and
allows us to cache the device revision information too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use the most simple possible transformation on the existing code so keep
the table sitting around, further patches in this series will delete the
existing cache code - the main purpose of this patch is to ensure that
we always have a cache for bisection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
During Device Tree enablement of the ab8500 and db8500-prcmu drivers,
a decision was made to omit registration through the MFD API and use
Device Tree directly. However, because MFD devices have a different
address space and the ab8500 and db8500 both use I2C to communicate,
this causes issues with address translation during execution of
of_platform_populate(). So the solution is to make the MFD core aware
of Device Tree and have it assign the correct node pointers instead.
To make this work the MFD core also needs to be awere of IRQ domains,
as Device Tree insists on IRQ domain compatibility. So, instead of
providing an irq-base via platform code, in the DT case we simply
look up the IRQ domain and map to the correct virtual IRQ.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
As the AB8500 is an IRQ controller in its own right, here we provide
the AB8500 driver with IRQ domain support. This is required if we wish
to reference any of its IRQs from a platform's Device Tree.
Cc: Naga Radheshy <naga.radheshy@stericsson.com>
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Cc: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Now this driver is using regmap APIs, the iolock mutex is not used and can be
removed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch is device driver for MAX77686 chip.
MAX77686 is PMIC and includes regulator and rtc on it.
This driver is core of MAX77686 chip, so provides common support for
accessing on-chip devices. It uses irq_domain to manage irq and regmap
to read/write data to its register with i2c bus.
Signed-off-by: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
|
|
The device managed flow steering API has three promiscuous modes:
1. Uplink - captures all the packets that arrive to the port.
2. Allmulti - captures all multicast packets arriving to the port.
3. Function port - for future use, this mode is not implemented yet.
Use these modes with the flow_attach and flow_detach firmware commands
according to the promiscuous state of the netdevice.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver is modified to support three operation modes.
If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.
When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.
When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.
Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for firmware commands to attach/detach a new device managed
steering mode. Such network steering rules allow the user to provide an
L2/L3/L4 flow specification to the firmware and have the device to steer
traffic that matches that specification to the provided QP.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of checking the firmware supported steering mode in various
places in the code, add a dedicated field in the mlx4 device capabilities
structure which is written once during the initialization flow and read
across the code.
This also set the grounds for add new steering modes. Currently two modes
are supported, and are named after the ConnectX HW versions A0 and B0.
A0 steering uses mac_index, vlan_index and priority to steer traffic
into pre-defined range of QPs.
B0 steering uses Ethernet L2 hashing rules and is enabled only
if the firmware supports both unicast and multicast B0 steering,
The current steering modes are relevant for Ethernet traffic only,
such that Infiniband steering remains untouched.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
atmel_mxt_ts driver by Daniel and MT protocol addition for win8 devices.
Conflicts:
drivers/input/touchscreen/atmel_mxt_ts.c
|
|
use threaded IRQs use IRQF_ONESHOT.
|
|
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The documentation didn't actually mention how to enable no_new_privs.
This also adds a note about possible interactions between
no_new_privs and LSMs (i.e. why teaching systemd to set no_new_privs
is not necessarily a good idea), and it references the new docs
from include/linux/prctl.h.
Suggested-by: Rob Landley <rob@landley.net>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Sebastian Zenker reported that driver swaps x and y samples when the
touchscreen leads are connected in accordance with the datasheet
specification. Transposed axis can be typically corrected by touch
screen calibration however this bug also negatively influences touch
pressure measurements.
Add an option to correct x and y axis.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reported-and-tested-by: Sebastian Zenker <sebastian.zenker@gmx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
