| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
After commit f5bf18fa22f8 ("bootmem/sparsemem: remove limit constraint
in alloc_bootmem_section"), usemap allocations may easily be placed
outside the optimal section that holds the node descriptor, even if
there is space available in that section. This results in unnecessary
hotplug dependencies that need to have the node unplugged before the
section holding the usemap.
The reason is that the bootmem allocator doesn't guarantee a linear
search starting from the passed allocation goal but may start out at a
much higher address absent an upper limit.
Fix this by trying the allocation with the limit at the section end,
then retry without if that fails. This keeps the fix from f5bf18fa22f8
of not panicking if the allocation does not fit in the section, but
still makes sure to try to stay within the section at first.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org> [3.3.x, 3.4.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
kswapd_stop() is called to destroy the kswapd work thread when all memory
of a NUMA node has been offlined. But kswapd_stop() only terminates the
work thread without resetting NODE_DATA(nid)->kswapd to NULL. The stale
pointer will prevent kswapd_run() from creating a new work thread when
adding memory to the memory-less NUMA node again. Eventually the stale
pointer may cause invalid memory access.
An example stack dump as below. It's reproduced with 2.6.32, but latest
kernel has the same issue.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81051a94>] exit_creds+0x12/0x78
PGD 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/system/memory/memory391/state
CPU 11
Modules linked in: cpufreq_conservative cpufreq_userspace cpufreq_powersave acpi_cpufreq microcode fuse loop dm_mod tpm_tis rtc_cmos i2c_i801 rtc_core tpm serio_raw pcspkr sg tpm_bios igb i2c_core iTCO_wdt rtc_lib mptctl iTCO_vendor_support button dca bnx2 usbhid hid uhci_hcd ehci_hcd usbcore sd_mod crc_t10dif edd ext3 mbcache jbd fan ide_pci_generic ide_core ata_generic ata_piix libata thermal processor thermal_sys hwmon mptsas mptscsih mptbase scsi_transport_sas scsi_mod
Pid: 7949, comm: sh Not tainted 2.6.32.12-qiuxishi-5-default #92 Tecal RH2285
RIP: 0010:exit_creds+0x12/0x78
RSP: 0018:ffff8806044f1d78 EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffff880604f22140 RCX: 0000000000019502
RDX: 0000000000000000 RSI: 0000000000000202 RDI: 0000000000000000
RBP: ffff880604f22150 R08: 0000000000000000 R09: ffffffff81a4dc10
R10: 00000000000032a0 R11: ffff880006202500 R12: 0000000000000000
R13: 0000000000c40000 R14: 0000000000008000 R15: 0000000000000001
FS: 00007fbc03d066f0(0000) GS:ffff8800282e0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 000000060f029000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process sh (pid: 7949, threadinfo ffff8806044f0000, task ffff880603d7c600)
Stack:
ffff880604f22140 ffffffff8103aac5 ffff880604f22140 ffffffff8104d21e
ffff880006202500 0000000000008000 0000000000c38000 ffffffff810bd5b1
0000000000000000 ffff880603d7c600 00000000ffffdd29 0000000000000003
Call Trace:
__put_task_struct+0x5d/0x97
kthread_stop+0x50/0x58
offline_pages+0x324/0x3da
memory_block_change_state+0x179/0x1db
store_mem_state+0x9e/0xbb
sysfs_write_file+0xd0/0x107
vfs_write+0xad/0x169
sys_write+0x45/0x6e
system_call_fastpath+0x16/0x1b
Code: ff 4d 00 0f 94 c0 84 c0 74 08 48 89 ef e8 1f fd ff ff 5b 5d 31 c0 41 5c c3 53 48 8b 87 20 06 00 00 48 89 fb 48 8b bf 18 06 00 00 <8b> 00 48 c7 83 18 06 00 00 00 00 00 00 f0 ff 0f 0f 94 c0 84 c0
RIP exit_creds+0x12/0x78
RSP <ffff8806044f1d78>
CR2: 0000000000000000
[akpm@linux-foundation.org: add pglist_data.kswapd locking comments]
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This converts the U300 clock implementation over to use the common
struct clk and moves the implementation down into drivers/clk.
Since VCO isn't used in tree it was removed, it's not hard to
put it back in if need be.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[mturquette@linaro.org: trivial Makefile conflict]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Allow drivers to declare their clk_init_data const, the framework really
shouldn't be modifying the data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Most platforms end up using a mix of basic clock types and
some which use clk_hw_foo struct for filling in custom platform
information when the clocks don't fit into basic types supported.
In platform code, its useful to know if a clock is using a basic
type or clk_hw_foo, which helps platforms know if they can
safely use to_clk_hw_foo to derive the clk_hw_foo pointer from
clk_hw.
Mark all basic clocks with a CLK_IS_BASIC flag.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Some divider clks do not have any obvious relationship
between the divider and the value programmed in the
register. For instance, say a value of 1 could signify divide
by 6 and a value of 2 could signify divide by 4 etc.
Also there are dividers where not all values possible
based on the bitfield width are valid. For instance
a 3 bit wide bitfield can be used to program a value
from 0 to 7. However its possible that only 0 to 4
are valid values.
All these cases need the platform code to pass a simple
table of divider/value tuple, so the framework knows
the exact value to be written based on the divider
calculation and can also do better error checking.
This patch adds support for such rate table based
dividers and as part of the support adds a new
registration function 'clk_register_divider_table()'
and a new macro for static definition
'DEFINE_CLK_DIVIDER_TABLE'.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
To finally fix the infamous leap second issue and other race windows
caused by functions which change the offsets between the various time
bases (CLOCK_MONOTONIC, CLOCK_REALTIME and CLOCK_BOOTTIME) we need a
function which atomically gets the current monotonic time and updates
the offsets of CLOCK_REALTIME and CLOCK_BOOTTIME with minimalistic
overhead. The previous patch which provides ktime_t offsets allows us
to make this function almost as cheap as ktime_get() which is going to
be replaced in hrtimer_interrupt().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/1341960205-56738-7-git-send-email-johnstul@us.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
clock_was_set() cannot be called from hard interrupt context because
it calls on_each_cpu().
For fixing the widely reported leap seconds issue it is necessary to
call it from hard interrupt context, i.e. the timer tick code, which
does the timekeeping updates.
Provide a new function which denotes it in the hrtimer cpu base
structure of the cpu on which it is called and raise the hrtimer
softirq. We then execute the clock_was_set() notificiation from
softirq context in run_hrtimer_softirq(). The hrtimer softirq is
rarely used, so polling the flag there is not a performance issue.
[ tglx: Made it depend on CONFIG_HIGH_RES_TIMERS. We really should get
rid of all this ifdeffery ASAP ]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Reported-by: Jan Engelhardt <jengelh@inai.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1341960205-56738-2-git-send-email-johnstul@us.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/mce
Merge memory fault handling fix from Tony Luck.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch replaces the usage of simple_strtoul with kstrtoint in
get_int(), since the simple_str* family doesn't account for overflow
and is deprecated.
Also, in this specific case, the long from strtol is silently converted
to an int by the caller.
As Joe Perches <joe@perches.com> suggested, this patch also removes
the redundant temporary variable rv, since kstrtoint() will not write to
anint unless it's successful.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Neaten code style in get_int().
Also use sizeof() instead of hard coded number as suggested by
Joe Perches <joe@perches.com>.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a few fixes and new device ids for the 3.5-rc6 tree.
The PCI changes resolve a long-standing issue with resuming some EHCI
controllers. It has been acked by the PCI maintainer, and he asked
for it to go through my USB tree instead of his.
The xhci patches also resolve a number of reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
PCI: EHCI: fix crash during suspend on ASUS computers
USB: cdc-wdm: fix lockup on error in wdm_read
USB: metro-usb: fix tty_flip_buffer_push use
USB: option: Add MEDIATEK product ids
USB: option: add ZTE MF60
xhci: Fix hang on back-to-back Set TR Deq Ptr commands.
usb: Add support for root hub port status CAS
|
|
paravirtualize them
To allow easy paravirtualization of P_Key and GID table sizes, keep
paravirtualized sizes in mlx4_dev->caps, but save the actual physical
sizes from FW in struct: mlx4_dev->phys_cap.
In addition, in SR-IOV mode, do the following:
1. Reduce reported P_Key table size by 1.
This is done to reserve the highest P_Key index for internal use,
for declaring an invalid P_Key in P_Key paravirtualization.
We require a P_Key index which always contain an invalid P_Key
value for this purpose (i.e., one which cannot be modified by
the subnet manager). The way to do this is to reduce the
P_Key table size reported to the subnet manager by 1, so that
it will not attempt to access the P_Key at index #127.
2. Paravirtualize the GID table size to 1. Thus, each guest sees
only a single GID (at its paravirtualized index 0).
In addition, since we are paravirtualizing the GID table size to 1, we
add paravirtualization of the master GID event here (i.e., we do not
do ib_dispatch_event() for the GUID change event on the master, since
its (only) GUID never changes).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The SR-IOV special QP tunneling mechanism uses proxy special QPs
(instead of the real special QPs) for MADs on guests. These proxy QPs
send their packets to a "tunnel" QP owned by the master. The master
then forwards the MAD (after any required paravirtualization) to the
real special QP, which sends out the MAD.
For security reasons (i.e., to prevent guests from sending MADs to
tunnel QPs belonging to other guests), each proxy-tunnel QP pair is
assigned a unique, reserved, Q_Key. These Q_Keys are available only
for proxy and tunnel QPs -- if the guest tries to use these Q_Keys
with other QPs, it will fail.
This patch introduces a mechanism for reserving a block of 64K Q_Keys
for proxy/tunneling use.
The patch introduces also two new fields into mlx4_dev: base_sqpn and
base_tunnel_sqpn.
In SR-IOV mode, the QP numbers for the "real," proxy, and tunnel sqps
are added to the reserved QPN area (so that they will not change).
There are 8 special QPs per port in the HCA, and each of them is
assigned both a proxy and a tunnel QP, for each VF and for the PF as
well in SR-IOV mode.
The QPNs for these QPs are arranged as follows:
1. The real SQP numbers (8)
2. The proxy SQPs (8 * (max number of VFs + max number of PFs)
3. The tunnel SQPs (8 * (max number of VFs + max number of PFs)
To support these QPs, two new fields are added to struct mlx4_dev:
base_sqp: this is the QP number of the first of the real SQPs
base_tunnel_sqp: this is the qp number of the first qp in the tunnel
sqp region. (On guests, this is the first tunnel
sqp of the 8 which are assigned to that guest).
In addition, in SR-IOV mode, sqp_start is the number of the first
proxy SQP in the proxy SQP region. (In guests, this is the first
proxy SQP of the 8 which are assigned to that guest)
Note that in non-SR-IOV mode, there are no proxies and no tunnels.
In this case, sqp_start is set to sqp_base -- which minimizes code
changes.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
In commit dad1743e5993f1 ("x86/mce: Only restart instruction after machine
check recovery if it is safe") we fixed mce_notify_process() to force a
signal to the current process if it was not restartable (RIPV bit not
set in MCG_STATUS). But doing it here means that the process doesn't
get told the virtual address of the fault via siginfo_t->si_addr. This
would prevent application level recovery from the fault.
Make a new MF_MUST_KILL flag bit for memory_failure() et al. to use so
that we will provide the right information with the signal.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: stable@kernel.org # 3.4+
|
|
In preparation to remove the slow revmap path, eliminate the public
radix revmap lookup functions. This simplifies the code and makes the
slowpath removal patch a lot simpler.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
|
|
This adds a new strict mapping API for supporting creation of linux IRQs
at existing positions within the domain. The new routines are as follows:
For dynamic allocation and insertion to specified ranges:
- irq_create_identity_mapping()
- irq_create_strict_mappings()
These will allocate and associate a range of linux IRQs at the specified
location. This can be used by controllers that have their own static linux IRQ
definitions to map a hwirq range to, as well as for platforms that wish to
establish 1:1 identity mapping between linux and hwirq space.
For insertion to specified ranges by platforms that do their own irq_desc
management:
- irq_domain_associate()
- irq_domain_associate_many()
These in turn call back in to the domain's ->map() routine, for further
processing by the platform. Disassociation of IRQs get handled through
irq_dispose_mapping() as normal.
With these in place it should be possible to begin migration of legacy IRQ
domains to linear ones, without requiring special handling for static vs
dynamic IRQ definitions in DT vs non-DT paths. This also makes it possible
for domains with static mappings to adopt whichever tree model best fits
their needs, rather than simply restricting them to linear revmaps.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
[grant.likely: Reorganized irq_domain_associate{,_many} to have all logic in one place]
[grant.likely: Add error checking for unallocated irq_descs at associate time]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
|
|
Linux 3.5-rc6
|
|
A large proportion of interrupt controllers that support legacy mappings
do so because non-DT systems need to use fixed IRQ numbers when registering
devices via buses but can otherwise use a linear mapping. The interrupt
controller itself typically is not affected by the mapping used and best
practice is to use a linear mapping where possible so drivers frequently
select at runtime depending on if a legacy range has been allocated to
them.
Standardise this behaviour by providing irq_domain_register_simple() which
will allocate a linear mapping unless a positive first_irq is provided in
which case it will fall back to a legacy mapping. This helps make best
practice for irq_domain adoption clearer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
USB 3.0 devices can optionally support Latency Tolerance Messaging
(LTM). Add a new sysfs file in the device directory to show whether a
device is LTM capable. This file will be present for both USB 2.0 and
USB 3.0 devices.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
USB 3.0 devices may optionally support a new feature called Latency
Tolerance Messaging. If both the xHCI host controller and the device
support LTM, it should be turned on in order to give the system hardware
a better clue about the latency tolerance values of its PCI devices.
Once a Set Feature request to enable LTM is received, the USB 3.0 device
will begin to send LTM updates as its buffers fill or empty, and it can
tolerate more or less latency.
The USB 3.0 spec, section C.4.2 says that LTM should be disabled just
before the device is placed into suspend. Then the device will send an
updated LTM notification, so that the system doesn't think it should
remain in an active state in order to satisfy the latency requirements
of the suspended device.
The Set and Clear Feature LTM enable command can only be sent to a
configured device. The device will respond with an error if that
command is sent while it is in the Default or Addressed state. Make
sure to check udev->actconfig in usb_enable_ltm() and usb_disable_ltm(),
and don't send those commands when the device is unconfigured.
LTM should be enabled once a new configuration is installed in
usb_set_configuration(). If we end up sending duplicate Set Feature LTM
Enable commands on a switch from one installed configuration to another
configuration, that should be harmless.
Make sure that LTM is disabled before the device is unconfigured in
usb_disable_device(). If no drivers are bound to the device, it doesn't
make sense to allow the device to control the latency tolerance of the
xHCI host controller.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
hub_initiated_lpm_disable_count is not used by any code, so remove it.
This commit should be backported to kernels as old as 3.5, that contain
the commit 8306095fd2c1100e8244c09bf560f97aca5a311d "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
Linux 3.5-rc6
Dependency for imx/soc changes
|
|
Implement the attribute itself and add the code for the
AMD IOMMU driver.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
This patch introduces an extension to the iommu-api to get
and set attributes for an iommu_domain. Two functions are
introduced for this:
* iommu_domain_get_attr()
* iommu_domain_set_attr()
These functions will be used to make the iommu-api suitable
for GART-like IOMMUs and to implement hardware-specifc
api-extensions.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Fixes build when ipv6 is disabled.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some power systems do not have legacy ISA devices. So, /dev/port is not
a valid interface on these systems. User level tools such as kbdrate is
trying to access the device using this interface which is causing the
system crash.
This patch will fix this issue by not creating this interface on these
powerpc systems.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Merge Linux 3.5-rc6 before merging more code.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Nobody provides non-zero values any longer.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No longer used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
prom_update_property() currently fails if the property doesn't
actually exist yet which isn't what we want. Change to add-or-update
instead of update-only, then we can remove a lot duplicated lines.
Suggested-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Nicolas Royer <nicolas@eukrea.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Eric Bénard <eric@eukrea.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
GPIOs can be used in MMC/SD-card slots not only for hotplug detection, but
also to implement the write-protection pin. Rename cd-gpio helpers to
slot-gpio to make addition of further slot GPIO functions possible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
A lot of code has either the memset or an inefficient copy
from a static array that contains the all-ones broadcast
address. Introduce eth_broadcast_addr() to fill an address
with all ones, making the code clearer and allowing us to
get rid of some constant arrays.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Yes, this is a *LATE* GPIO pull request with fixes for v3.5.
Grant moved across the planet and accidentally fell off the grid, so
he asked me to take over the GPIO merges for a while 10 days ago.
Since then I went over the archives and collected this pile of fixes,
and pulled two of them from the TI maintainer Kevin Hilman. Then
waited for them to at least hit linux-next once or twice."
GPIO fixes for v3.5:
- Invalid context restore on bank 0 for OMAP driver in runtime
suspend/resume cycle
- Check for NULL platform data in sta-2x11 driver
- Constrain selection of the V1 MSM GPIO driver to applicable platforms
(Kconfig issue)
- Make sure the correct output value is set in the wm8994 driver
- Export devm_gpio_request_one() so it can be used in modules.
Apparently some in-kernel modules can be configured to use this
leading to breakage.
- Check that the GPIO is valid in the lantiq driver
- Fix the flag bits introduced for v3.5, so they don't overlap
- Fix a device tree intialization bug for imx21-compatible devices
- Carry over the OF node to the TPS65910 GPIO chip struct
* tag 'fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tps65910: initialize of_node of gpio_chip
gpio/mxc: make irqs work for fsl,imx21-gpio devices
gpio: fix bits conflict for gpio flags
mips: pci-lantiq: Fix check for valid gpio
gpio: export devm_gpio_request_one
gpiolib: wm8994: Pay attention to the value set when enabling as output
gpio/msm_v1: CONFIG_GPIO_MSM_V1 is only available on three SoCs
gpio-sta2x11: don't use pdata if null
gpio/omap: fix invalid context restore of gpio bank-0
gpio/omap: fix irq loss while in idle with debounce on
|
|
On certain bios, resume hangs if cpus are allowed to enter idle states
during suspend [1].
This was fixed in apci idle driver [2].But intel_idle driver does not
have this fix. Thus instead of replicating the fix in both the idle
drivers, or in more platform specific idle drivers if needed, the
more general cpuidle infrastructure could handle this.
A suspend callback in cpuidle_driver could handle this fix. But
a cpuidle_driver provides only basic functionalities like platform idle
state detection capability and mechanisms to support entry and exit
into CPU idle states. All other cpuidle functions are found in the
cpuidle generic infrastructure for good reason that all cpuidle
drivers, irrepective of their platforms will support these functions.
One option therefore would be to register a suspend callback in cpuidle
which handles this fix. This could be called through a PM_SUSPEND_PREPARE
notifier. But this is too generic a notfier for a driver to handle.
Also, ideally the job of cpuidle is not to handle side effects of suspend.
It should expose the interfaces which "handle cpuidle 'during' suspend"
or any other operation, which the subsystems call during that respective
operation.
The fix demands that during suspend, no cpus should be allowed to enter
deep C-states. The interface cpuidle_uninstall_idle_handler() in cpuidle
ensures that. Not just that it also kicks all the cpus which are already
in idle out of their idle states which was being done during cpu hotplug
through a CPU_DYING_FROZEN callbacks.
Now the question arises about when during suspend should
cpuidle_uninstall_idle_handler() be called. Since we are dealing with
drivers it seems best to call this function during dpm_suspend().
Delaying the call till dpm_suspend_noirq() does no harm, as long as it is
before cpu_hotplug_begin() to avoid race conditions with cpu hotpulg
operations. In dpm_suspend_noirq(), it would be wise to place this call
before suspend_device_irqs() to avoid ugly interactions with the same.
Ananlogously, during resume.
References:
[1] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/674075.
[2] http://marc.info/?l=linux-pm&m=133958534231884&w=2
Reported-and-tested-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Add iio channel type and modifiers for Correlated Color Temperature (CCT)
and RGBC (red/green/blue/clear) data.
Add CCT and RGBC descriptions to documentation.
Changes:
Revised/condensed RGBC descriptions.
Merge and trivial fix done by Jonathan Cameron.
Signed-off-by: Jon Brenner <jbrenner@taosinc.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
With IB SR-IOV, each slave has its own separate copy of the port
capabilities flags. For example, the master can run a subnet manager
(which causes the IsSM bit to be set in the master's port
capabilities) without affecting the port capabilities seen by the
slaves (the IsSM bit will be seen as cleared in the slaves).
Also add a static inline mlx4_master_func_num() to enhance readability
of the code.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Quite a few ASUS computers experience a nasty problem, related to the
EHCI controllers, when going into system suspend. It was observed
that the problem didn't occur if the controllers were not put into the
D3 power state before starting the suspend, and commit
151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during
suspend on ASUS computers) was created to do this.
It turned out this approach messed up other computers that didn't have
the problem -- it prevented USB wakeup from working. Consequently
commit c2fb8a3fa25513de8fedb38509b1f15a5bbee47b (USB: add
NO_D3_DURING_SLEEP flag and revert 151b61284776be2) was merged; it
reverted the earlier commit and added a whitelist of known good board
names.
Now we know the actual cause of the problem. Thanks to AceLan Kao for
tracking it down.
According to him, an engineer at ASUS explained that some of their
BIOSes contain a bug that was added in an attempt to work around a
problem in early versions of Windows. When the computer goes into S3
suspend, the BIOS tries to verify that the EHCI controllers were first
quiesced by the OS. Nothing's wrong with this, but the BIOS does it
by checking that the PCI COMMAND registers contain 0 without checking
the controllers' power state. If the register isn't 0, the BIOS
assumes the controller needs to be quiesced and tries to do so. This
involves making various MMIO accesses to the controller, which don't
work very well if the controller is already in D3. The end result is
a system hang or memory corruption.
Since the value in the PCI COMMAND register doesn't matter once the
controller has been suspended, and since the value will be restored
anyway when the controller is resumed, we can work around the BIOS bug
simply by setting the register to 0 during system suspend. This patch
(as1590) does so and also reverts the second commit mentioned above,
which is now unnecessary.
In theory we could do this for every PCI device. However to avoid
introducing new problems, the patch restricts itself to EHCI host
controllers.
Finally the affected systems can suspend with USB wakeup working
properly.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=37632
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=42728
Based-on-patch-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Javier Marcet <jmarcet@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel <bug-track@fisher-privat.net>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: stable <stable@vger.kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The port management change event can replace smp_snoop. If the
capability bit for this event is set in dev-caps, the event is used
(by the driver setting the PORT_MNG_CHG_EVENT bit in the async event
mask in the MAP_EQ fw command). In this case, when the driver passes
incoming SMP PORT_INFO SET mads to the FW, the FW generates port
management change events to signal any changes to the driver.
If the FW generates these events, smp_snoop shouldn't be invoked in
ib_process_mad(), or duplicate events will occur (once from the
FW-generated event, and once from smp_snoop).
In the case where the FW does not generate port management change
events smp_snoop needs to be invoked to create these events. The flow
in smp_snoop has been modified to make use of the same procedures as
in the fw-generated-event event case to generate the port management
events (LID change, Client-rereg, Pkey change, and/or GID change).
Port management change event handling required changing the
mlx4_ib_event and mlx4_dispatch_event prototypes; the "param" argument
(last argument) had to be changed to unsigned long in order to
accomodate passing the EQE pointer.
We also needed to move the definition of struct mlx4_eqe from
net/mlx4.h to file device.h -- to make it available to the IB driver,
to handle port management change events.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This patch does the following:
-const int of_get_nand_ecc_mode(struct device_node *np)
+int of_get_nand_ecc_mode(struct device_node *np)
because:
1. it is probably just a typo?
2. it causes warnings like this when people assing the returned
value to an 'int' variable:
include/linux/of_mtd.h:14:18: warning: type qualifiers ignored on functi=
on return type [-Wignored-qualifiers]
Remove also the unnecessary "extern" qualifier to be consistent with other
declarations in this file.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
* pci/bjorn-p2p-bridge-windows:
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: allow P2P bridge windows starting at PCI bus address zero
Conflicts:
drivers/pci/probe.c
include/linux/pci.h
|
|
Timer 0 is used as free-running clocksource, while timer 1 is used as
clock_event_device.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: John Stultz <johnstul@us.ibm.com>
|
|
A few more registers used on newer devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The registers have stride 2 so we can write the loop properly now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This begins the migration of the PFC core to the pinctrl subsystem.
Initial support is very basic, with the bulk of the implementation simply
being nopped out in such a way to allow registration with the pinctrl
core to succeed.
The gpio chip driver is stripped down considerably now relying purely on
pinctrl API calls to manage the bulk of its operations.
This provides a basis for further PFC refactoring, including decoupling
pin functions from the GPIO API, establishing pin groups, and so forth.
These will all be dealt with incrementally so as to introduce as few
growing and migratory pains to tree-wide PFC pinmux users today.
When the interfaces have been well established and in-tree users have
been migrated off of the legacy interfaces it will be possible to strip
down the core considerably, leading to eventual drivers/pinctrl rehoming.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This implements fairly simplistic stringification of existing pinmux
GPIOs for easy enum id -> string mapping, which will subsequently be used
by the pinctrl support code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
This follows the intc/clk changes and shuffles the PFC support code under
its own directory. This will facilitate better code sharing, and allow us
to trim down the exported interface by quite a margin.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
