| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Some platforms have problems when EEE is enabled, and thus need a way
to disable stmmac EEE support. Add a flag before the other LPI related
flags which tells stmmac to avoid populating the phylink LPI
capabilities, which causes phylink to call phy_disable_eee() for any
PHY that is attached to the affected phylink instance.
iMX8MP is an example - the lpi_intr_o signal is wired to an OR gate
along with the main dwmac interrupts. Since lpi_intr_o is synchronous
to the receive clock domain, and takes four clock cycles to clear, this
leads to interrupt storms as the interrupt remains asserted for some
time after the LPI control and status register is read.
This problem becomes worse when the receive clock from the PHY stops
when the receive path enters LPI state - which means that lpi_intr_o
can not deassert until the clock restarts. Since the LPI state of the
receive path depends on the link partner, this is out of our control.
We could disable RX clock stop at the PHY, but that doesn't get around
the slow-to-deassert lpi_intr_o mentioned in the above paragraph.
Previously, iMX8MP worked around this by disabling gigabit EEE, but
this is insufficient - the problem is also visible at 100M speeds,
where the receive clock is slower.
There is extensive discussion and investigation in the thread linked
below, the result of which is summarised in this commit message.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Closes: https://lore.kernel.org/r/20251026122905.29028-1-laurent.pinchart@ideasonboard.com
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Link: https://patch.msgid.link/20260325210003.2752013-2-laurent.pinchart@ideasonboard.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
axi_kbbe, axi_mb and axi_rb are all written, but nothing ever reads
their values. Remove the code that sets these and the struct members.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w4ydo-0000000Dlpb-34jd@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The integrated PCS supports 802.3z (BASE-X) modes when the Synopsys
IP is coupled with an appropriate SerDes to provide the electrical
interface. The PCS presents a TBI interface to the SerDes for this.
Thus, the BASE-X related registers are only present when TBI mode is
supported.
dwmac-qcom-ethqos added support for using 2.5G with the integrated PCS
by calling dwmac_ctrl_ane() directly.
Add support for the following to the integrated PCS:
- 1000BASE-X protocol unconditionally.
- 2500BASE-X if the coupled SerDes supports 2.5G speed.
- The above without autonegotiation.
- If the PCS supports TBI, then optional BASE-X autonegotiation for each
of the above.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w2tPe-0000000DYAp-1qpV@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the default_an_inband flag from struct mdio_bus_data to struct
plat_stmmacenet_data. This is to allow platforms that do not use the
integrated MDIO bus to enable inband mode.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w2tPP-0000000DYAX-0TKw@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The pci_dev is only used to provide the ethtool bus_info using
pci_name(priv->plat->pdev). This is the same as dev_name(priv->device).
Thus, rather than passing the pci_dev, make use of what we already
have.
To avoid unexpectedly exposing the device name through ethtool where
it wasn't provided before, add a flag priv->plat->provide_bus_info
to enable this, which only dwmac-intel needs to set.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/E1w0evI-0000000CzY7-1fyo@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add documentation covering stmmac_clk, pclk, clk_ptp_ref and clk_tx_i
in the hope that this will help understand what each of these clocks
are for.
There is confusion around stmmac_clk and pclk which can't be easily
resolved today as the Imagination Technologies Pistachio board that
pclk was introduced for has no public documentation and is likely now
obsolete. So the origins of pclk are lost to the winds of time.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX5Z-0000000CVsb-1XTm@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add documentation of each of the struct stmmac_dma_cfg members. dche
remains undocumented as I don't have documentation that covers this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX5U-0000000CVsQ-162V@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We aren't going to see >= 256-bit address busses soon, so reduce
host_dma_width and associated other struct members that initialise
this from u32 to u8.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com> # qcom-ethqos
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX5P-0000000CVsK-0iwX@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The maximum number of queues is a compile time constant of only eight.
This makes using a 32-bit quantity wastefulf. Instead, use u8 for
these and their associated variables.
When reading the DT properties, saturdate at U8_MAX. Provided the core
provides DMA capabilities to describe the number of queues, this will
be capped by stmmac_hw_init() with a warning.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX5K-0000000CVsE-0J0Y@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reorder some of the stmmac structures to allow them to pack better,
thereby using less memory. On aarch64, sizeof(struct stmmac_priv)
was 880, and with this change becomes 816, saving 64 bytes, which
is an 8% saving.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX5E-0000000CVs8-40w4@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert members of struct plat_stmmacenet_data that are booleans to
type 'bool' and ensure their initialisers are true/false. Move the
has_xxx for the GMAC cores together, and move the COE members to the
end of the list of bool to avoid unused holes in the struct.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX59-0000000CVs2-3MHc@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
plat_dat->dma_cfg is unconditionally required for the operation of the
driver, so it would make sense to allocate it along with the plat_dat.
On Arm64, sizeof(*plat_dat) has recently shrunk from 880 to 816 bytes
and sizeof(*plat_dat->dma_cfg) has shrunk from 32 to 20 bytes.
Given that dma_cfg is required, and it is now less than a cache line,
It doesn't make sense to allocate this separateny, so place it at the
end of struct plat_stmmacenet_data, and set plat_dat->dma_cfg to point
at that to avoid mass changes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Link: https://patch.msgid.link/E1vzX54-0000000CVrw-2jfu@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The PCS and PHY masks are passed to the mdio bus layer as phy_mask
to prevent bus addresses between 0 and 31 inclusive being scanned,
and this is declared as u32. Also declare these as u32 in stmmac
for type consistency.
Since this is a u32, use BIT_U32() rather than BIT() to generate
values for these fields.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1vy6AY-0000000BtxJ-3smT@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
default_an_inband is declared as an unsigned int, but is set to true/
false and is assigned to phylink_config's member of the same name
which is a bool. Declare this also as a bool for consistency.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1vy6AT-0000000BtxD-2qm7@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
struct stmmac_dma_cfg mixed_burst/fixed_burst members are both boolean
in nature - of_property_read_bool() are used to read these from DT, and
they are only tested for non-zero values. Use bool to avoid unnecessary
padding in this structure.
Update dwmac-intel to initialise these using true rather than '1', and
remove the '0' initialisers as the struct is already zero initialised
on allocation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vvuXn-0000000AvnX-4A1u@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are repeated instances of:
fwnode = priv->plat->port_node;
if (!fwnode)
fwnode = dev_fwnode(priv->device);
However, the only place that ->port_node is set is
stmmac_probe_config_dt():
struct device_node *np = pdev->dev.of_node;
...
/* PHYLINK automatically parses the phy-handle property */
plat->port_node = of_fwnode_handle(np);
which is equivalent to dev_fwnode(&pdev->dev) and, as priv->device
will be &pdev->dev, is also equivalent to dev_fwnode(priv->device).
Thus, plat_dat->port_node doesn't provide any extra benefit over
using dev_fwnode(priv->device) directly.
There is one case where port_node is used directly, which can be
found in stmmac_pcs_setup(). This may cause a change of behaviour
as PCI drivers do not populate plat_dat->port_node, but
dev_fwnode(priv->device) may be valid. PCI-based stmmac should
be tested.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vvuX3-0000000Avme-3oej@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass the current interface mode reported by phylink into the
fix_mac_speed() method. This will be used by qcom-ethqos for its
"SGMII" configuration.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vuSKv-0000000AScG-1zv6@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dwmac databook for v3.74a states that lpi_intr_o is a sideband
signal which should be used to ungate the application clock, and this
signal is synchronous to the receive clock. The receive clock can run
at 2.5, 25 or 125MHz depending on the media speed, and can stop under
the control of the link partner. This means that the time it takes to
clear is dependent on the negotiated media speed, and thus can be 8,
40, or 400ns after reading the LPI control and status register.
It has been observed with some aggressive link partners, this clock
can stop while lpi_intr_o is still asserted, meaning that the signal
remains asserted for an indefinite period that the local system has
no direct control over.
The LPI interrupts will still be signalled through the main interrupt
path in any case, and this path is not dependent on the receive clock.
This, since we do not gate the application clock, and the chances of
adding clock gating in the future are slim due to the clocks being
ill-defined, lpi_intr_o serves no useful purpose. Remove the code which
requests the interrupt, and all associated code.
Reported-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Tested-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com> # Renesas RZ/V2H board
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vnJbt-00000007YYN-28nm@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In include/linux/stmmac.h clk_csr_i is spelled as clk_scr_i by mistake,
so correct the typo.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Yanteng Si <siyanteng@cqsoftware.com.cn>
Link: https://patch.msgid.link/20260203062658.2156653-1-chenhuacai@loongson.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As the stmmac_priv struct is passed to the fix_soc_reset() method which
has the ioaddr, there is no need to pass ioaddr separately. Pass just
the stmmac_priv struct. Fix up the glues that use it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1vkLmM-00000005vE1-0nop@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The stmmac implementation used by NXP for the i.MX8MP SoC is subject to
errata ERR050694. According to this errata, when no preamble byte is
transferred before the SFD from the PHY to the MAC, the MAC will discard
the frame.
Setting the PHY_F_KEEP_PREAMBLE_BEFORE_SFD flag instructs PHYs that
support it to keep the preamble byte before the SFD. This ensures that
the MAC successfully receives frames.
As this is an issue in the MAC implementation, only enable the flag for
the i.MX8MP SoC where the errata applies but not for other SoCs using a
working stmmac implementation.
The exact wording of the errata ERR050694 from NXP:
The IEEE 802.3 standard states that, in MII/GMII modes, the byte
preceding the SFD (0xD5), SMD-S (0xE6,0x4C, 0x7F, or 0xB3), or SMD-C
(0x61, 0x52, 0x9E, or 0x2A) byte can be a non-PREAMBLE byte or there can
be no preceding preamble byte. The MAC receiver must successfully
receive a packet without any preamble(0x55) byte preceding the SFD,
SMD-S, or SMD-C byte.
However due to the defect, in configurations where frame preemption is
enabled, when preamble byte does not precede the SFD, SMD-S, or SMD-C
byte, the received packet is discarded by the MAC receiver. This is
because, the start-of-packet detection logic of the MAC receiver
incorrectly checks for a preamble byte.
NXP refers to IEEE 802.3 where in clause 35.2.3.2.2 Receive case (GMII)
they show two tables one where the preamble is preceding the SFD and one
where it is not. The text says:
The operation of 1000 Mb/s PHYs can result in shrinkage of the preamble
between transmission at the source GMII and reception at the destination
GMII. Table 35-3 depicts the case where no preamble bytes are conveyed
across the GMII. This case may not be possible with a specific PHY, but
illustrates the minimum preamble with which MAC shall be able to
operate. Table 35-4 depicts the case where the entire preamble is
conveyed across the GMII.
This workaround was tested on a Verdin iMX8MP by enforcing 10 MBit/s:
ethtool -s end0 speed 10
Without keeping the preamble, no packet were received. With keeping the
preamble, everything worked as expected.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260120203905.23805-4-eichest@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the axi_blen array from struct stmmac_axi as we set this array,
and then immediately convert it ot the register value, never looking at
the array again. Thus, the array can be function local rather than part
of a run-time allocated long-lived struct.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vLfLg-0000000FMbD-1vmh@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the call to stmmac_axi_blen_to_mask() out of the individual
MAC version drivers into the main code in stmmac_init_dma_engine(),
passing the resulting value through a new member, axi_blen_regval,
in the struct stmmac_axi structure.
There is now no need for stmmac_axi_blen_to_dma_mask() to use
u32p_replace_bits(), so use FIELD_PREP() instead.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vLfLW-0000000FMb1-0zKV@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As struct plat_stmmacenet_data is not platform_device specific, pass
a struct device into the init() and exit() methods to allow them to
become independent of the underlying device.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Chen-Yu Tsai <wens@kernel.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1vLf2U-0000000FMN2-0SLg@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ->setup() method implemented by dwmac-loongson and dwmac-sun8i
allocate the mac_device_info structure, as does stmmac_hwif_init().
This makes no sense.
Have stmmac_hwif_init() always allocate this structure, and pass it to
the ->setup() method to initialise when it is provided. Rename this
method to "mac_setup" to more accurately describe what it is doing.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vImWK-0000000DrIx-28vO@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When dwmac is synthesised with support for multiple PHY interfaces, the
core provides phy_intf_sel inputs, sampled on reset, to configure the
PHY facing interface. Use stmmac_get_phy_intf_sel() in core code to
determine the dwmac phy_intf_sel input value, and provide a new
platform method called with this value just before we issue a soft
reset to the dwmac core.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vFt4h-0000000Chos-3wxX@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace the has_gmac, has_gmac4 and has_xgmac ints, of which only one
can be set when matching a core to its driver backend, with an
enumerated type carrying the DWMAC core type.
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Chen-Yu Tsai <wens@kernel.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/E1vB6ld-0000000BIPy-2Qi4@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Changing the netif_carrier_*() state behind phylink's back has always
been prohibited because it messes up with phylinks state tracking, and
means that phylink no longer guarantees to call the mac_link_down()
and mac_link_up() methods at the appropriate times. This was later
documented in the sfp-phylink network driver conversion guide.
stmmac was converted to phylink in 2019, but nothing was done with the
"PCS" code. Since then, apart from the updates as part of phylink
development, nothing has happened with stmmac to improve its use of
phylink, or even to address this point.
A couple of years ago, a has_integrated_pcs boolean was added by Bart,
which later became the STMMAC_FLAG_HAS_INTEGRATED_PCS flag, to avoid
manipulating the netif_carrier_*() state. This flag is mis-named,
because whenever the stmmac is synthesized for its native SGMII, TBI
or RTBI interfaces, it has an "integrated PCS". This boolean/flag
actually means "ignore the status from the integrated PCS".
Discussing with Bart, the reasons for this are lost to the winds of
time (which is why we should always document the reasons in the commit
message.)
RGMII also has in-band status, and the dwmac cores and stmmac code
supports this but with one bug that saves the day.
When dwmac cores are synthesised for RGMII only, they do not contain
an integrated PCS, and so priv->dma_cap.pcs is clear, which prevents
(incorrectly) the "RGMII PCS" being used, meaning we don't read the
in-band status. However, a core synthesised for RGMII and also SGMII,
TBI or RTBI will have this capability bit set, thus making these
code paths reachable.
The Jetson Xavier NX uses RGMII mode to talk to its PHY, and removing
the incorrect check for priv->dma_cap.pcs reveals the theortical issue
with netif_carrier_*() manipulation is real:
dwc-eth-dwmac 2490000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
dwc-eth-dwmac 2490000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=141)
dwc-eth-dwmac 2490000.ethernet eth0: No Safety Features support found
dwc-eth-dwmac 2490000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
dwc-eth-dwmac 2490000.ethernet eth0: registered PTP clock
dwc-eth-dwmac 2490000.ethernet eth0: configuring for phy/rgmii-id link mode
8021q: adding VLAN 0 to HW filter on device eth0
dwc-eth-dwmac 2490000.ethernet eth0: Adding VLAN ID 0 is not supported
Link is Up - 1000/Full
Link is Down
Link is Up - 1000/Full
This looks good until one realises that the phylink "Link" status
messages are missing, even when the RJ45 cable is reconnected. Nothing
one can do results in the interface working. The interrupt handler
(which prints those "Link is" messages) always wins over phylink's
resolve worker, meaning phylink never calls the mac_link_up() nor
mac_link_down() methods.
eth0 also sees no traffic received, and is unable to obtain a DHCP
address:
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group defa
ult qlen 1000
link/ether e6:d3:6a:e6:92:de brd ff:ff:ff:ff:ff:ff
RX: bytes packets errors dropped overrun mcast
0 0 0 0 0 0
TX: bytes packets errors dropped carrier collsns
27686 149 0 0 0 0
With the STMMAC_FLAG_HAS_INTEGRATED_PCS flag set, which disables the
netif_carrier_*() manipulation then stmmac works normally:
dwc-eth-dwmac 2490000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
dwc-eth-dwmac 2490000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=141)
dwc-eth-dwmac 2490000.ethernet eth0: No Safety Features support found
dwc-eth-dwmac 2490000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
dwc-eth-dwmac 2490000.ethernet eth0: registered PTP clock
dwc-eth-dwmac 2490000.ethernet eth0: configuring for phy/rgmii-id link mode
8021q: adding VLAN 0 to HW filter on device eth0
dwc-eth-dwmac 2490000.ethernet eth0: Adding VLAN ID 0 is not supported
Link is Up - 1000/Full
dwc-eth-dwmac 2490000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
and packets can be transferred.
This clearly shows that when priv->hw->pcs is set, but
STMMAC_FLAG_HAS_INTEGRATED_PCS is clear, the driver reliably fails.
Discovering whether a platform falls into this is impossible as
parsing all the dtsi and dts files to find out which use the stmmac
driver, whether any of them use RGMII or SGMII and also depends
whether an external interface is being used. The kernel likely
doesn't contain all dts files either.
The only driver that sets this flag uses the qcom,sa8775p-ethqos
compatible, and uses SGMII or 2500BASE-X.
but these are saved from this problem by the incorrect check for
priv->dma_cap.pcs.
So, we have to assume that for every other platform that uses SGMII
with stmmac is using an external PCS.
Moreover, ethtool output can be incorrect. With the full-duplex link
negotiated, ethtool reports:
Speed: 1000Mb/s
Duplex: Half
because with dwmac4, the full-duplex bit is in bit 16 of the status,
priv->xstats.pcs_duplex becomes BIT(16) for full duplex, but the
ethtool ksettings duplex member is u8 - so becomes zero. Moreover,
the supported, advertised and link partner modes are all "not
reported".
Finally, ksettings_set() won't be able to set the advertisement on
a PHY if this PCS code is activated, which is incorrect when SGMII
is used with a PHY.
Thus, remove:
1. the incorrect netif_carrier_*() manipulation.
2. the broken ethtool ksettings code.
Given that all uses of STMMAC_FLAG_HAS_INTEGRATED_PCS are now gone,
remove the flag from stmmac.h and dwmac-qcom-ethqos.c.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P5y-0000000AolC-1QWH@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mac_interface has served little purpose, and has only caused confusion.
Now that we have cleaned up all platform glue drivers which should not
have been using mac_interface, there are no users remaining. Remove
mac_interface.
This results in the special dwmac specific "mac-mode" DT property
becoming redundant, and an in case, no DTS files in the kernel make use
of this property. Add a warning if the property is set, and it is
different from the "phy-mode".
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://patch.msgid.link/E1uytpv-00000006H2x-196h@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Based on new research, it has come to light that the comment that I
added in a014c35556b9 ("net: stmmac: clarify difference between
"interface" and "phy_interface"") is not fully correct.
Update the comment to properly describe the difference between the two.
All of the DTS files in the kernel tree do not mention the "mac-mode"
property, which results in mac_interface and phy_interface being the
same. Also, none of the platform glue drivers set mac_interface to
anything but PHY_INTERFACE_MODE_NA. This means that for all the
platforms known to mainline, mac_interface is either the same as
phy_interface, or it is PHY_INTERFACE_MODE_NA.
Thus, updating the definition for mac_interface in stmmac.h has no
material effect on current uses known to mainline, but the change opens
the door to cleaning up all uses.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1uytpB-00000006H23-0pRi@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In order to use netdev_err() to print message in the callback function of
fix_soc_reset(), change fix_soc_reset() to have "struct stmmac_priv *" as
its first parameter.
This is preparation for later patch, no functionality change.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://patch.msgid.link/20250811073506.27513-3-yangtiezhu@loongson.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add suspend/resume platform operations, which, when populated, override
the init/exit platform operations when we suspend and resume. These
suspend()/resume() methods are called by core code, and thus are
designed to support any struct device, not just platform devices. This
allows them to be used by the PCI drivers we have.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1ulXbX-008gqZ-Bb@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the speed_mode_2500() platform method which is no longer used
or necessary, being superseded by the more flexible get_interfaces()
method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uASM3-0021R3-2B@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a get_interfaces() platform method to allow platforms to indicate
to phylink which interface modes they support - which then allows
phylink to validate on initialisation that the configured PHY interface
mode is actually supported.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1uASLn-0021Qd-Mi@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
plat_dat->eee_users_rate is now unused, so remove this member.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1u3Vuv-000E7y-9k@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow platform glue to instruct stmmac to make use of the PHY transmit
clock stop capability when deciding whether to allow the transmit clock
from the DWMAC core to be stopped.
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsITp-005vG9-Px@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
SerDes will configure according to the provided interface mode after
finish a major reconfiguration of the interface mode.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Link: https://patch.msgid.link/20250227121522.1802832-5-yong.liang.choong@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Several stmmac sub-drivers which support RGMII follow the same pattern.
They calculate the transmit clock rate, and then call clk_set_rate().
Analysis of several implementation documents suggests that the platform
is responsible for providing the transmit clock to the DWMAC core's
clk_tx_i. The expected rates are:
10Mbps 100Mbps 1Gbps
MII 2.5MHz 25MHz
RMII 2.5MHz 25MHz
GMII 125MHz
RGMI 2.5MHz 25MHz 125MHz
It seems some platforms require this clock to be manually configured,
but there are outputs from the MAC core that indicate the speed, so a
platform may use these to automatically configure the clock. Thus, we
can't just provide one solution to configure this clock rate.
Moreover, the clock may need to be derived from one of several sources
depending on the interface mode.
Provide a platform hook that is passed the transmit clock, interface
mode and speed.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1tna0F-0052sS-Lr@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
priv->plat->fix_mac_speed() is called from stmmac_mac_link_up(), which
is passed the speed as an "int". However, fix_mac_speed() implicitly
casts this to an unsigned int. Some platform glue code print this value
using %u, others with %d. Some implicitly cast it back to an int, and
others to u32.
Good practice is to use one type and only one type to represent a value
being passed around a driver.
Switch all of these over to consistently use "int" when dealing with a
speed passed from stmmac_mac_link_up(), even though the speed will
always be positive.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://patch.msgid.link/E1tkKmN-004ObM-Ge@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Refactor clock management in EQoS driver for code reuse and to avoid
redundancy. This way, only minimal changes are required when a new platform
is added.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Swathi K S <swathi.ks@samsung.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250213041559.106111-1-swathi.ks@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The clock API clk_get_rate() returns unsigned long value.
Expand affected members of stmmac platform data and
convert the stmmac_clk_csr_set() and dwmac4_core_init() methods
to defining the unsigned long clk_rate local variables.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-3-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for CSR clock range up to 800 MHz.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-2-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The comment in declaration of STMMAC_CSR_250_300M
incorrectly describes the constant as '/* MDC = clk_scr_i/122 */'
but the DWC Ether QOS Handbook version 5.20a says it is
CSR clock/124.
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-1-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
By moving the fpe_cfg field to the stmmac_priv data, stmmac_fpe_cfg
becomes platform-data eventually, instead of a run-time config.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://patch.msgid.link/d9b3d7ecb308c5e39778a4c8ae9df288a2754379.1725631883.git.0x1207@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ATDS (Alternate Descriptor Size) is a part of the DMA Bus Mode configs
(together with PBL, ALL, EME, etc) of the DW GMAC controllers. Seeing
it's not changed at runtime but is activated as long as the IP-core
has it supported (at least due to the Type 2 Full Checksum Offload
Engine feature), move the respective parameter from the
stmmac_dma_ops::init() callback argument to the stmmac_dma_cfg
structure, which already have the rest of the DMA-related configs
defined.
Besides the being added in the next commit DW GMAC multi-channels
support will require to add the stmmac_dma_ops::init_chan() callback
and have the ATDS flag set/cleared for each channel in there. Having
the atds-flag in the stmmac_dma_cfg structure will make the parameter
accessible from stmmac_dma_ops::init_chan() callback too.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently the only STMMAC platform driver using the DW XPCS code is the
Intel mGBE device driver. (It can be determined by finding all the drivers
having the stmmac_mdio_bus_data::has_xpcs flag set.) At the same time the
low-level platform driver masks out the DW XPCS MDIO-address from being
auto-detected as PHY by the MDIO subsystem core. Seeing the PCS MDIO ID is
known the procedure of the DW XPCS device creation can be simplified by
dropping the loop over all the MDIO IDs. From now the DW XPCS device
descriptor will be created for the MDIO-bus address pre-defined by the
platform drivers via the stmmac_mdio_bus_data::pcs_mask field.
Note besides this shall speed up a bit the Intel mGBE probing.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow platform drivers to provide their logic to select an appropriate
PCS.
Tested-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1sHhoM-00Fesu-8E@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rename xpcs_an_inband to default_an_inband to reflect the change in
phylink and its changed functionality.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/E1sCJN6-00EcrD-43@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the EST structure to struct stmmac_priv, because the
EST configs don't look like platform config, but EST is
enabled in runtime with the settings retrieved for the TC
TAPRIO feature also in runtime. So it's better to have the
EST-data preserved in the driver private data instead of
the platform data storage.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240513014346.1718740-3-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reinitialize the whole EST structure would also reset the mutex
lock which is embedded in the EST structure, and then trigger
the following warning. To address this, move the lock to struct
stmmac_priv. We also need to reacquire the mutex lock when doing
this initialization.
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 3 PID: 505 at kernel/locking/mutex.c:587 __mutex_lock+0xd84/0x1068
Modules linked in:
CPU: 3 PID: 505 Comm: tc Not tainted 6.9.0-rc6-00053-g0106679839f7-dirty #29
Hardware name: NXP i.MX8MPlus EVK board (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __mutex_lock+0xd84/0x1068
lr : __mutex_lock+0xd84/0x1068
sp : ffffffc0864e3570
x29: ffffffc0864e3570 x28: ffffffc0817bdc78 x27: 0000000000000003
x26: ffffff80c54f1808 x25: ffffff80c9164080 x24: ffffffc080d723ac
x23: 0000000000000000 x22: 0000000000000002 x21: 0000000000000000
x20: 0000000000000000 x19: ffffffc083bc3000 x18: ffffffffffffffff
x17: ffffffc08117b080 x16: 0000000000000002 x15: ffffff80d2d40000
x14: 00000000000002da x13: ffffff80d2d404b8 x12: ffffffc082b5a5c8
x11: ffffffc082bca680 x10: ffffffc082bb2640 x9 : ffffffc082bb2698
x8 : 0000000000017fe8 x7 : c0000000ffffefff x6 : 0000000000000001
x5 : ffffff8178fe0d48 x4 : 0000000000000000 x3 : 0000000000000027
x2 : ffffff8178fe0d50 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
__mutex_lock+0xd84/0x1068
mutex_lock_nested+0x28/0x34
tc_setup_taprio+0x118/0x68c
stmmac_setup_tc+0x50/0xf0
taprio_change+0x868/0xc9c
Fixes: b2aae654a479 ("net: stmmac: add mutex lock to protect est parameters")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240513014346.1718740-2-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
