| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add a new flag, PHY_F_KEEP_PREAMBLE_BEFORE_SFD, to indicate that the PHY
shall not remove the preamble before the SFD if it supports it. MACs
that do not support receiving frames without a preamble can set this
flag.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260120203905.23805-2-eichest@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No user of PHY fixups unregisters these. IOW: The fixup unregistering
functions are unused and can be removed. Remove also documentation
for these functions. Whilst at it, remove also mentioning of
phy_register_fixup() from the Documentation, as this function has been
static since ea47e70e476f ("net: phy: remove fixup-related definitions
from phy.h which are not used outside phylib").
Fixup unregistering functions were added with f38e7a32ee4f
("phy: add phy fixup unregister functions") in 2016, and last user
was removed with 6782d06a47ad ("net: usb: lan78xx: Remove KSZ9031 PHY
fixup") in 2024.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/ff8ac321-435c-48d0-b376-fbca80c0c22e@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that all PHY drivers that support downstream SFP have been converted
to phy_port serdes handling, we can make the generic PHY SFP handling
mandatory, thus making all phylib sfp helpers static.
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260108080041.553250-14-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are currently 4 PHY drivers that can drive downstream SFPs:
marvell.c, marvell10g.c, at803x.c and marvell-88x2222.c. Most of the
logic is boilerplate, either calling into generic phylib helpers (for
SFP PHY attach, bus attach, etc.) or performing the same tasks with a
bit of validation :
- Getting the module's expected interface mode
- Making sure the PHY supports it
- Optionaly perform some configuration to make sure the PHY outputs
the right mode
This can be made more generic by leveraging the phy_port, and its
configure_mii() callback which allows setting a port's interfaces when
the port is a serdes.
Introduce a generic PHY SFP support. If a driver doesn't probe the SFP
bus itself, but an SFP phandle is found in devicetree/firmware, then the
generic PHY SFP support will be used, relying on port ops.
PHY driver need to :
- Register a .attach_port() callback
- When a serdes port is registered to the PHY, drivers must set
port->interfaces to the set of PHY_INTERFACE_MODE the port can output
- If the port has limitations regarding speed, duplex and aneg, the
port can also fine-tune the final linkmodes that can be supported
- The port may register a set of ops, including .configure_mii(), that
will be called at module_insert time to adjust the interface based on
the module detected.
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260108080041.553250-8-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ethernet provides a wide variety of layer 1 protocols and standards for
data transmission. The front-facing ports of an interface have their own
complexity and configurability.
Introduce a representation of these front-facing ports. The current code
is minimalistic and only support ports controlled by PHY devices, but
the plan is to extend that to SFP as well as raw Ethernet MACs that
don't use PHY devices.
This minimal port representation allows describing the media and number
of pairs of a BaseT port. From that information, we can derive the
linkmodes usable on the port, which can be used to limit the
capabilities of an interface.
For now, the port pairs and medium is derived from devicetree, defined
by the PHY driver, or populated with default values (as we assume that
all PHYs expose at least one port).
The typical example is 100M ethernet. 100BaseTX works using only 2
pairs on a Cat 5 cables. However, in the situation where a 10/100/1000
capable PHY is wired to its RJ45 port through 2 pairs only, we have no
way of detecting that. The "max-speed" DT property can be used, but a
more accurate representation can be used :
mdi {
connector-0 {
media = "BaseT";
pairs = <2>;
};
};
From that information, we can derive the max speed reachable on the
port.
Another benefit of having that is to avoid vendor-specific DT properties
(micrel,fiber-mode or ti,fiber-mode).
This basic representation is meant to be expanded, by the introduction
of port ops, userspace listing of ports, and support for multi-port
devices.
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260108080041.553250-4-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for reading Signal Quality Indicator (SQI) and enhanced SQI+
from OATC14 10Base-T1S PHYs.
- Introduce MDIO register definitions for DCQ_SQI and DCQ_SQIPLUS.
- Add `genphy_c45_oatc14_get_sqi_max()` to return the maximum supported
SQI/SQI+ level.
- Add `genphy_c45_oatc14_get_sqi()` to return the current SQI or SQI+
value.
- Update `include/linux/phy.h` to expose the new APIs.
SQI+ capability is read from the Advanced Diagnostic Features Capability
register (ADFCAP). If SQI+ is supported, the driver calculates the value
from the MSBs of the DCQ_SQIPLUS register; otherwise, it falls back to
basic SQI (0-7 levels). This enables ethtool to report the SQI value for
OATC14 10Base-T1S PHYs.
Open Alliance TC14 10BASE-T1S Advanced Diagnostic PHY Features
Specification ref:
https://opensig.org/wp-content/uploads/2025/06/OPEN_Alliance_10BASE-T1S_Advanced_PHY_features_for-automotive_Ethernet_V2.1b.pdf
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251201032346.6699-2-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PHY devices has hwtstamp callback which actually performs set operation.
Rename it to better reflect the action.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251124181151.277256-2-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "phy-mode" property of devicetree indicates whether the PCB has
delay now, which means the mac needs to modify the PHY mode based
on whether there is an internal delay in the mac.
This modification is similar for many ethernet drivers. To simplify
code, define the helper phy_fix_phy_mode_for_mac_delays(speed, mac_txid,
mac_rxid) to fix PHY mode based on whether mac adds internal delay.
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251114003805.494387-3-inochiama@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for Open Alliance TC14 (OATC14) 10BASE-T1S PHYs cable
diagnostic feature.
This patch implements:
- genphy_c45_oatc14_cable_test_start() to initiate a cable test
- genphy_c45_oatc14_cable_test_get_status() to retrieve test results
- Helper function to map PHY cable test status to ethtool result codes
- Function declarations and exports for use by PHY drivers
This enables ethtool to report ok, open, short, and undetectable cable
conditions on OATC14 10Base-T1S PHYs.
Open Alliance TC14 10BASE-T1S Advanced Diagnostic PHY Features
Specification ref:
https://opensig.org/wp-content/uploads/2025/06/OPEN_Alliance_10BASE-T1S_Advanced_PHY_features_for-automotive_Ethernet_V2.1b.pdf
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20251105051213.50443-2-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We can reduce the size of struct phy_device a little by switching
the type of members pause and asym_pause from int to a single bit.
As C99 is supported now, we can use type bool for the bitfield members,
what provides us with the benefit of the usual implicit bool conversions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/764e9a31-b40b-4dc9-b808-118192a16d87@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the base infrastructure for Mean Square Error (MSE) diagnostics,
as proposed by the OPEN Alliance "Advanced diagnostic features for
100BASE-T1 automotive Ethernet PHYs" [1] specification.
The OPEN Alliance spec defines only average MSE and average peak MSE
over a fixed number of symbols. However, other PHYs, such as the
KSZ9131, additionally expose a worst-peak MSE value latched since the
last channel capture. This API accounts for such vendor extensions by
adding a distinct capability bit and snapshot field.
Channel-to-pair mapping is normally straightforward, but in some cases
(e.g. 100BASE-TX with MDI-X resolution unknown) the mapping is ambiguous.
If hardware does not expose MDI-X status, the exact pair cannot be
determined. To avoid returning misleading per-channel data in this case,
a LINK selector is defined for aggregate MSE measurements.
All investigated devices differ in MSE capabilities, such
as sample rate, number of analyzed symbols, and scaling factors.
For example, the KSZ9131 uses different scaling for MSE and pMSE.
To make this visible to callers, scale limits and timing information
are returned via get_mse_capability().
Some PHYs sample very few symbols at high frequency (e.g. 2 us update
rate). To cover such cases and allow for future high-speed PHYs with
even shorter intervals, the refresh rate is reported as u64 in
picoseconds.
This patch introduces the internal PHY API for Mean Square Error
diagnostics. It defines new kernel-side data types and driver hooks:
- struct phy_mse_capability: describes supported metrics, scale
limits, update interval, and sampling length.
- struct phy_mse_snapshot: holds one correlated measurement set.
- New phy_driver ops: `get_mse_capability()` and `get_mse_snapshot()`.
These definitions form the core kernel API. No user-visible interfaces
are added in this commit.
Standardization notes:
OPEN Alliance defines presence and interpretation of some metrics but does
not fix numeric scales or sampling internals:
- SQI (3-bit, 0..7) is mandatory; correlation to SNR/BER is informative
(OA 100BASE-T1 TC1 v1.0 6.1.2; OA 1000BASE-T1 TC12 v2.2 6.1.2).
- MSE is optional; OA recommends 2^16 symbols and scaling to 0..511,
with a worst-case latch since last read (OA 100BASE-T1 TC1 v1.0 6.1.1; OA
1000BASE-T1 TC12 v2.2 6.1.1). Refresh is recommended (~0.8-2.0 ms for
100BASE-T1; ~80-200 us for 1000BASE-T1). Exact scaling/time windows
are vendor-specific.
- Peak MSE (pMSE) is defined only for 100BASE-T1 as optional, e.g.
128-symbol sliding window with 8-bit range and worst-case latch (OA
100BASE-T1 TC1 v1.0 6.1.3).
Therefore this API exposes which measures and selectors a PHY supports,
and documents where behavior is standard-referenced vs vendor-specific.
[1] <https://opensig.org/wp-content/uploads/2024/01/
Advanced_PHY_features_for_automotive_Ethernet_V1.0.pdf>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20251027122801.982364-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add an iterator for all PHY's on a MII bus, and phy_find_next()
as a prerequisite.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/cd112f15-401a-43d9-8525-9ff0965a68cd@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add phy_may_wakeup() which uses the driver model's device_may_wakeup()
when the PHY driver has marked the device as wakeup capable in the
driver model, otherwise use phy_drv_wol_enabled().
Replace the sites that used to call phy_drv_wol_enabled() with this
as checking the driver model will be more efficient than checking the
WoL state.
Export phy_may_wakeup() so that phylink can use it.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vBrQx-0000000BLzO-1RLt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add phy_can_wakeup() to report whether the PHY driver has marked the
PHY device as being wake-up capable as far as the driver model is
concerned.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vBrQs-0000000BLzI-0w3U@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix typos in doc comments.
Signed-off-by: Bhanu Seshu Kumar Valluri <bhanuseshukumar@gmail.com>
Link: https://patch.msgid.link/20251001105715.50462-1-bhanuseshukumar@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After 42e2a9e11a1d ("net: phy: dp83640: improve phydev and driver
removal handling") we can stop exporting also phy_driver_unregister().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/2bab950e-4b70-4030-b997-03f48379586f@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phy_driver_register() isn't used outside phy_device.c any longer,
so we can stop exporting it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/dff44b83-4a85-4fff-bf6b-f12efd97b56e@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a helper for copying PHY interface bitmasks. This will be used by
the SFP bus code, which will then be moved to phylink in the subsequent
patches.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1uydVU-000000061W8-2IDT@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After having removed mdio_board_info usage from dsa_loop, there's no
user left. So let's drop support for it from phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/01542a2e-05f5-4f13-acef-72632b33b5be@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Similar to phy_id_compare_vendor(), introduce the equivalent
phy_id_compare_model() helper for the generic PHY ID Model mask.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250911130840.23569-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.17-rc5).
No conflicts.
Adjacent changes:
include/net/sock.h
c51613fa276f ("net: add sk->sk_drop_counters")
5d6b58c932ec ("net: lockless sock_i_ino()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uslwn-00000001SOx-0a7H@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce phy_id_compare_vendor() PHY ID helper to compare a PHY ID with
the PHY ID Vendor using the generic PHY ID Vendor mask.
While at it also rework the PHY_ID_MATCH macro and move the mask to
dedicated define so that PHY driver can make use of the mask if needed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250823134431.4854-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some Broadcom PHYs are capable to operate in simplified MII mode,
without TXER, RXER, CRS and COL signals as defined for the MII.
The MII-Lite mode can be used on most Ethernet controllers with full
MII interface by just leaving the input signals (RXER, CRS, COL)
inactive. The absence of COL signal makes half-duplex link modes
impossible but does not interfere with BroadR-Reach link modes on
Broadcom PHYs, because they are all full-duplex only.
Add MII-Lite interface mode, especially for Broadcom two-wire PHYs.
Signed-off-by: Kamil Horák - 2N <kamilh@axis.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250708090140.61355-2-kamilh@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
is enabled
Now that we have an own config symbol for the PHY package module,
we can use it to reduce size of these structs if it isn't enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/f0daefa4-406a-4a06-a4f0-7e31309f82bc@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for 802.3cd based interface types 50GBASE-R and 100GBASE-P.
This choice in naming is based on section 135 of the 802.3-2022 IEEE
Standard.
In addition it is adding support for what I am referring to as LAUI
which is based on annex 135C of the IEEE Standard, and shares many
similarities with the 25/50G consortium. The main difference between the
two is that IEEE spec refers to LAUI as the AUI before the RS(544/514) FEC,
whereas the 25/50G use this lane and frequency combination after going
through RS(528/514), Base-R or no FEC at all.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://patch.msgid.link/175028444205.625704.4191700324472974116.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove now unused function phy_driver_is_genphy_10g().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/49b0589a-9604-4ee9-add5-28fbbbe2c2f3@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use new flag phydev->is_genphy_driven to simplify this function.
Note that this includes a minor functional change:
Now this function returns true if ANY of the genphy drivers
is bound to the PHY device.
We have only one user in DSA driver mt7530, and there the
functional change doesn't matter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/c9ac3a7d-262a-425d-9153-97fe3ca6280a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In order to get rid of phy_driver_is_genphy() and
phy_driver_is_genphy_10g(), as first step add and use a flag
phydev->is_genphy_driven.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/3f3ad6dc-402e-4915-8d5a-2306b6d5562b@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Improve the rgmii_clock() documentation to indicate that it can also
be used for MII, GMII and RMII modes as well as RGMII as the required
clock rates are identical, but note that it won't error out for 1G
speeds for MII and RMII.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uPjjk-0049pI-MD@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplify the arguments passed to phy_get_internal_delay() - the "dev"
argument is always &phydev->mdio.dev, and as the phydev is passed in,
there's no need to also pass in the struct device, especially when this
function is the only reason for the caller to have a local "dev"
variable.
Remove the redundant "dev" argument, and update the callers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1uPLwB-003VzR-4C@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
genphy_c45_read_status() is exported, so we can move definition of
genphy_c45_driver to phy_device.c and make it static. This helps
to clean up phy.h a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/ead3ab17-22d0-4cd3-901c-3d493ab851e6@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Both to_mdio_device() and to_phy_device() "throw away" the const pointer
attribute passed to them and return a non-const pointer, which generally
is not a good thing overall. Fix this up by using container_of_const()
which was designed for this very problem.
Cc: Alexander Lobakin <alobakin@pm.me>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Fixes: 7eab14de73a8 ("mdio, phy: fix -Wshadow warnings triggered by nested container_of()")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2025052246-conduit-glory-8fc9@gregkh
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce new API, genphy_match_phy_device(), to provide a way to check
to match a PHY driver for a PHY device based on the info stored in the
PHY device struct.
The function generalize the logic used in phy_bus_match() to check the
PHY ID whether if C45 or C22 ID should be used for matching.
This is useful for custom .match_phy_device function that wants to use
the generic logic under some condition. (example a PHY is already setup
and provide the correct PHY ID)
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-5-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass PHY driver pointer to .match_phy_device OP in addition to phydev.
Having access to the PHY driver struct might be useful to check the
PHY ID of the driver is being matched for in case the PHY ID scanned in
the phydev is not consistent.
A scenario for this is a PHY that change PHY ID after a firmware is
loaded, in such case, the PHY ID stored in PHY device struct is not
valid anymore and PHY will manually scan the ID in the match_phy_device
function.
Having the PHY driver info is also useful for those PHY driver that
implement multiple simple .match_phy_device OP to match specific MMD PHY
ID. With this extra info if the parsing logic is the same, the matching
function can be generalized by using the phy_id in the PHY driver
instead of hardcoding.
Rust wrapper callback is updated to align to the new match_phy_device
arguments.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Benno Lossin <lossin@kernel.org> # for Rust
Reviewed-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-2-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After having factored out the provider part from mdio_bus.c, we can
make the mdio consumer / device layer a separate module. This also
allows to remove Kconfig symbol MDIO_DEVICE.
The module init / exit functions from mdio_bus.c no longer have to be
called from phy_device.c. The link order defined in
drivers/net/phy/Makefile ensures that init / exit functions are called
in the right order.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/dba6b156-5748-44ce-b5e2-e8dc2fcee5a7@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The functionality of mdiobus_register_board_info() typically isn't
optional for the caller. Therefore remove the stub.
Note: Currently we have only one caller of mdiobus_register_board_info(),
in a DSA/PHYLINK context. Therefore CONFIG_MDIO_DEVICE is selected anyway.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/410a2222-c4e8-45b0-9091-d49674caeb00@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After 52358dd63e34 ("net: phy: remove function stubs") there's a
problem if CONFIG_MDIO_BUS is set, but CONFIG_PHYLIB is not.
mdiobus_scan() uses phylib functions like get_phy_device().
Bringing back the stub wouldn't make much sense, because it would
allow to compile mdiobus_scan(), but the function would be unusable.
The stub returned NULL, and we have the following in mdiobus_scan():
phydev = get_phy_device(bus, addr, c45);
if (IS_ERR(phydev))
return phydev;
So calling mdiobus_scan() w/o CONFIG_PHYLIB would cause a crash later in
mdiobus_scan(). In general the PHYLIB functionality isn't optional here.
Consequently, MDIO bus providers depend on PHYLIB.
Therefore factor it out and build it together with the libphy core
modules. In addition make all MDIO bus providers under /drivers/net/mdio
depend on PHYLIB. Same applies to enetc MDIO bus provider. Note that
PHYLIB selects MDIO_DEVRES, therefore we can omit this here.
Fixes: 52358dd63e34 ("net: phy: remove function stubs")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202504270639.mT0lh2o1-lkp@intel.com/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c74772a9-dab6-44bf-a657-389df89d85c2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All callers of these functions depend on PHYLIB or select it directly
or indirectly by selecting PHYLINK. Stubs make sense for optional
functionality, but that's not the case here.
MDIO_XGENE usually is selected by NET_XGENE which also selects PHYLIB.
Add a dependency to PHYLIB nevertheless, in order not to break
randconfig builds.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/f7a69a1f-60e9-4ac0-8b7c-481e0cc850e7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add helper which returns the MAC termination resistance value. Modifying
the resistance to an appropriate value can reduce signal reflections and
therefore improve signal quality.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Link: https://patch.msgid.link/20250416-dp83822-mac-impedance-v3-3-028ac426cddb@liebherr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
AFAICS this function has never had a user.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/ab7b8094-2eea-4e82-a047-fd60117f220b@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The PHY_ID_FMT defines the format specifier "%s:%02x" to form
the PHY ID string, where the maximum of the first part is defined
in MII_BUS_ID_SIZE, including NUL terminator, and the second part
is implied to be 3 as the maximum address is limited to 32, meaning
that 2 hex digits is more than enough, plus ':' (colon) delimiter.
However, some drivers, which are using PHY_ID_FMT, customise buffer
size and do that incorrectly. Introduce a new constant PHY_ID_SIZE
that makes the minimum required size explicit, so drivers are
encouraged to use it.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250324144751.1271761-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix copy-paste error in the code comment for Interface Mode definitions.
The code refers to Internal TX delay, not Internal RX delay. It was likely
copied from the line above this one.
Signed-off-by: Ihor Matushchak <ihor.matushchak@foobox.net>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250316071551.9794-1-ihor.matushchak@foobox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phy_loopback() leaves it to the PHY driver to select the speed of the
loopback mode. Thus, the speed of the loopback mode depends on the PHY
driver in use.
Add support for speed selection to phy_loopback() to enable loopback
with defined speeds. Ensure that link up is signaled if speed changes
as speed is not allowed to change during link up. Link down and up is
necessary for a new speed.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://patch.msgid.link/20250312203010.47429-3-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
PHY drivers support loopback mode, but it is not possible to select the
speed of the loopback mode. The speed is chosen by the set_loopback()
operation of the PHY driver. Same is valid for genphy_loopback().
There are PHYs that support loopback with different speeds. Extend
set_loopback() to make loopback speed selection possible.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250312203010.47429-2-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The phy_settings array is no longer relevant as it has now been replaced
by the link_caps array and associated phy_caps helpers.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-11-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use the newly introduced link_capabilities array to derive the list of
possible speeds when given a combination of linkmodes. As
link_capabilities is indexed by speed, we don't have to iterate the
whole phy_settings array.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-4-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
These functions have never had a user, so remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/5792e2cd-6f0a-4f7d-a5ef-b932f94d82f3@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phylib.h
These functions are used by PHY drivers only, therefore move their
declaration to phylib.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/406c8a20-b62e-4ee3-b174-b566724a0876@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move definition of struct phy_package_shared to phy_package.c, and
move remaining PHY package related declarations from phy.h to
phylib.h, thus making them accessible for PHY drivers only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/211e14b6-e2f8-43d7-b533-3628ec548456@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
