| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When phy_ethtool_set_eee_noneg() detects a change in the LPI
parameters, it attempts to update phylib state and trigger the link
to cycle so the MAC sees the updated parameters.
However, in doing so, it sets phydev->enable_tx_lpi depending on
whether the EEE configuration allows the MAC to generate LPI without
taking into account the result of negotiation.
This can be demonstrated with a 1000base-T FD interface by:
# ethtool --set-eee eno0 advertise 8 # cause EEE to be not negotiated
# ethtool --set-eee eno0 tx-lpi off
# ethtool --set-eee eno0 tx-lpi on
This results in being true, despite EEE not having been negotiated and:
# ethtool --show-eee eno0
EEE status: enabled - inactive
Tx LPI: 250 (us)
Supported EEE link modes: 100baseT/Full
1000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
Fix this by keeping track of whether EEE was negotiated via a new
eee_active member in struct phy_device, and include this state in
the decision whether phydev->enable_tx_lpi should be set.
Fixes: 3e43b903da04 ("net: phy: Immediately call adjust_link if only tx_lpi_enabled changes")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tErSe-005RhB-2R@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"The most significant set of changes is the per netns RTNL. The new
behavior is disabled by default, regression risk should be contained.
Notably the new config knob PTP_1588_CLOCK_VMCLOCK will inherit its
default value from PTP_1588_CLOCK_KVM, as the first is intended to be
a more reliable replacement for the latter.
Core:
- Started a very large, in-progress, effort to make the RTNL lock
scope per network-namespace, thus reducing the lock contention
significantly in the containerized use-case, comprising:
- RCU-ified some relevant slices of the FIB control path
- introduce basic per netns locking helpers
- namespacified the IPv4 address hash table
- remove rtnl_register{,_module}() in favour of
rtnl_register_many()
- refactor rtnl_{new,del,set}link() moving as much validation as
possible out of RTNL lock
- convert all phonet doit() and dumpit() handlers to RCU
- convert IPv4 addresses manipulation to per-netns RTNL
- convert virtual interface creation to per-netns RTNL
the per-netns lock infrastructure is guarded by the
CONFIG_DEBUG_NET_SMALL_RTNL knob, disabled by default ad interim.
- Introduce NAPI suspension, to efficiently switching between busy
polling (NAPI processing suspended) and normal processing.
- Migrate the IPv4 routing input, output and control path from direct
ToS usage to DSCP macros. This is a work in progress to make ECN
handling consistent and reliable.
- Add drop reasons support to the IPv4 rotue input path, allowing
better introspection in case of packets drop.
- Make FIB seqnum lockless, dropping RTNL protection for read access.
- Make inet{,v6} addresses hashing less predicable.
- Allow providing timestamp OPT_ID via cmsg, to correlate TX packets
and timestamps
Things we sprinkled into general kernel code:
- Add small file operations for debugfs, to reduce the struct ops
size.
- Refactoring and optimization for the implementation of page_frag
API, This is a preparatory work to consolidate the page_frag
implementation.
Netfilter:
- Optimize set element transactions to reduce memory consumption
- Extended netlink error reporting for attribute parser failure.
- Make legacy xtables configs user selectable, giving users the
option to configure iptables without enabling any other config.
- Address a lot of false-positive RCU issues, pointed by recent CI
improvements.
BPF:
- Put xsk sockets on a struct diet and add various cleanups. Overall,
this helps to bump performance by 12% for some workloads.
- Extend BPF selftests to increase coverage of XDP features in
combination with BPF cpumap.
- Optimize and homogenize bpf_csum_diff helper for all archs and also
add a batch of new BPF selftests for it.
- Extend netkit with an option to delegate skb->{mark,priority}
scrubbing to its BPF program.
- Make the bpf_get_netns_cookie() helper available also to tc(x) BPF
programs.
Protocols:
- Introduces 4-tuple hash for connected udp sockets, speeding-up
significantly connected sockets lookup.
- Add a fastpath for some TCP timers that usually expires after
close, the socket lock contention.
- Add inbound and outbound xfrm state caches to speed up state
lookups.
- Avoid sending MPTCP advertisements on stale subflows, reducing
risks on loosing them.
- Make neighbours table flushing more scalable, maintaining per
device neigh lists.
Driver API:
- Introduce a unified interface to configure transmission H/W
shaping, and expose it to user-space via generic-netlink.
- Add support for per-NAPI config via netlink. This makes napi
configuration persistent across queues removal and re-creation.
Requires driver updates, currently supported drivers are:
nVidia/Mellanox mlx4 and mlx5, Broadcom brcm and Intel ice.
- Add ethtool support for writing SFP / PHY firmware blocks.
- Track RSS context allocation from ethtool core.
- Implement support for mirroring to DSA CPU port, via TC mirror
offload.
- Consolidate FDB updates notification, to avoid duplicates on
device-specific entries.
- Expose DPLL clock quality level to the user-space.
- Support master-slave PHY config via device tree.
Tests and tooling:
- forwarding: introduce deferred commands, to simplify the cleanup
phase
Drivers:
- Updated several drivers - Amazon vNic, Google vNic, Microsoft vNic,
Intel e1000e and Broadcom Tigon3 - to use netdev-genl to link the
IRQs and queues to NAPI IDs, allowing busy polling and better
introspection.
- Ethernet high-speed NICs:
- nVidia/Mellanox:
- mlx5:
- a large refactor to implement support for cross E-Switch
scheduling
- refactor H/W conter management to let it scale better
- H/W GRO cleanups
- Intel (100G, ice)::
- add support for ethtool reset
- implement support for per TX queue H/W shaping
- AMD/Solarflare:
- implement per device queue stats support
- Broadcom (bnxt):
- improve wildcard l4proto on IPv4/IPv6 ntuple rules
- Marvell Octeon:
- Add representor support for each Resource Virtualization Unit
(RVU) device.
- Hisilicon:
- add support for the BMC Gigabit Ethernet
- IBM (EMAC):
- driver cleanup and modernization
- Cisco (VIC):
- raise the queues number limit to 256
- Ethernet virtual:
- Google vNIC:
- implement page pool support
- macsec:
- inherit lower device's features and TSO limits when
offloading
- virtio_net:
- enable premapped mode by default
- support for XDP socket(AF_XDP) zerocopy TX
- wireguard:
- set the TSO max size to be GSO_MAX_SIZE, to aggregate larger
packets.
- Ethernet NICs embedded and virtual:
- Broadcom ASP:
- enable software timestamping
- Freescale:
- add enetc4 PF driver
- MediaTek: Airoha SoC:
- implement BQL support
- RealTek r8169:
- enable TSO by default on r8168/r8125
- implement extended ethtool stats
- Renesas AVB:
- enable TX checksum offload
- Synopsys (stmmac):
- support header splitting for vlan tagged packets
- move common code for DWMAC4 and DWXGMAC into a separate FPE
module.
- add dwmac driver support for T-HEAD TH1520 SoC
- Synopsys (xpcs):
- driver refactor and cleanup
- TI:
- icssg_prueth: add VLAN offload support
- Xilinx emaclite:
- add clock support
- Ethernet switches:
- Microchip:
- implement support for the lan969x Ethernet switch family
- add LAN9646 switch support to KSZ DSA driver
- Ethernet PHYs:
- Marvel: 88q2x: enable auto negotiation
- Microchip: add support for LAN865X Rev B1 and LAN867X Rev C1/C2
- PTP:
- Add support for the Amazon virtual clock device
- Add PtP driver for s390 clocks
- WiFi:
- mac80211
- EHT 1024 aggregation size for transmissions
- new operation to indicate that a new interface is to be added
- support radio separation of multi-band devices
- move wireless extension spy implementation to libiw
- Broadcom:
- brcmfmac: optional LPO clock support
- Microchip:
- add support for Atmel WILC3000
- Qualcomm (ath12k):
- firmware coredump collection support
- add debugfs support for a multitude of statistics
- Qualcomm (ath5k):
- Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
- Realtek:
- rtw88: 8821au and 8812au USB adapters support
- rtw89: add thermal protection
- rtw89: fine tune BT-coexsitence to improve user experience
- rtw89: firmware secure boot for WiFi 6 chip
- Bluetooth
- add Qualcomm WCN785x support for ids Foxconn 0xe0fc/0xe0f3 and
0x13d3:0x3623
- add Realtek RTL8852BE support for id Foxconn 0xe123
- add MediaTek MT7920 support for wireless module ids
- btintel_pcie: add handshake between driver and firmware
- btintel_pcie: add recovery mechanism
- btnxpuart: add GPIO support to power save feature"
* tag 'net-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1475 commits)
mm: page_frag: fix a compile error when kernel is not compiled
Documentation: tipc: fix formatting issue in tipc.rst
selftests: nic_performance: Add selftest for performance of NIC driver
selftests: nic_link_layer: Add selftest case for speed and duplex states
selftests: nic_link_layer: Add link layer selftest for NIC driver
bnxt_en: Add FW trace coredump segments to the coredump
bnxt_en: Add a new ethtool -W dump flag
bnxt_en: Add 2 parameters to bnxt_fill_coredump_seg_hdr()
bnxt_en: Add functions to copy host context memory
bnxt_en: Do not free FW log context memory
bnxt_en: Manage the FW trace context memory
bnxt_en: Allocate backing store memory for FW trace logs
bnxt_en: Add a 'force' parameter to bnxt_free_ctx_mem()
bnxt_en: Refactor bnxt_free_ctx_mem()
bnxt_en: Add mem_valid bit to struct bnxt_ctx_mem_type
bnxt_en: Update firmware interface spec to 1.10.3.85
selftests/bpf: Add some tests with sockmap SK_PASS
bpf: fix recursive lock when verdict program return SK_PASS
wireguard: device: support big tcp GSO
wireguard: selftests: load nf_conntrack if not present
...
|
|
Merge in late fixes to prepare for the 6.13 net-next PR.
Conflicts:
include/linux/phy.h
41ffcd95015f net: phy: fix phylib's dual eee_enabled
721aa69e708b net: phy: convert eee_broken_modes to a linkmode bitmap
https://lore.kernel.org/all/20241118135512.1039208b@canb.auug.org.au/
drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
2160428bcb20 net: txgbe: fix null pointer to pcs
2160428bcb20 net: txgbe: remove GPIO interrupt controller
Adjacent commits:
include/linux/phy.h
41ffcd95015f net: phy: fix phylib's dual eee_enabled
516a5f11eb97 net: phy: respect cached advertising when re-enabling EEE
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phylib has two eee_enabled members. Some parts of the code are using
phydev->eee_enabled, other parts are using phydev->eee_cfg.eee_enabled.
This leads to incorrect behaviour as their state goes out of sync.
ethtool --show-eee shows incorrect information, and --set-eee sometimes
doesn't take effect.
Fix this by only having one eee_enabled member - that in eee_cfg.
Fixes: 49168d1980e2 ("net: phy: Add phy_support_eee() indicating MAC support EEE")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/E1tBXAF-00341F-EQ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add an accessor for eee_broken_modes, so that drivers
don't have to deal with phylib internals.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/0f8ee279-d40d-4489-a3b0-d993472d744a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
eee_broken_modes has a eee_cap1 register layout currently. This doen't
allow to flag e.g. 2.5Gbps or 5Gbps BaseT EEE as broken. To overcome
this limitation switch eee_broken_modes to a linkmode bitmap.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/dfe0c9ff-84b0-4328-86d7-e917ebc084a1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bcm_config_lre_aneg() doesn't use genphy_config_eee_advert() any longer.
As this was the only user, we can remove genphy_config_eee_advert() now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/37da7f3e-b883-4c07-9881-b8c0516822b7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
genphy_c45_write_eee_adv() isn't used outside phy-c45.c,
so make it static.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/d23bd784-44e6-4a15-af3a-b37379156521@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Function descriptions in iopoll.h, regmap.h, phy.h and sound/soc/sof/ops.h
copied all the same outdated documentation about sleep/delay function
limitations. In those comments, the generic (and still outdated) timer
documentation file is referenced.
As proper function descriptions for used delay and sleep functions are in
place, simply update the descriptions to reference to them. While at it fix
missing colon after "Returns" in function description and move return value
description to the end of the function description.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch> # for phy.h
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/all/20241014-devel-anna-maria-b4-timers-flseep-v3-12-dc8b907cb62f@linutronix.de
|
|
In addition to 'active-low' and 'inactive-high-impedance' also
support 'active-high' property for PHY LED pin configuration.
As only either 'active-high' or 'active-low' can be set at the
same time, WARN and return an error in case both are set.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/91598487773d768f254d5faf06cf65b13e972f0e.1728558223.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce support for configuring the master/slave role of PHYs based on
the `timing-role` property in the device tree. While this functionality
is necessary for Single Pair Ethernet (SPE) PHYs (1000/100/10Base-T1)
where hardware strap pins may be unavailable or incorrectly set, it
works for any PHY type.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are a few PHY drivers that can handle SFP modules through their
sfp_upstream_ops. Introduce Phylib helpers to keep track of connected
SFP PHYs in a netdevice's namespace, by adding the SFP PHY to the
upstream PHY's netdev's namespace.
By doing so, these SFP PHYs can be enumerated and exposed to users,
which will be able to use their capabilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to. The PHY index can be
re-used for PHYs that are persistent.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases
to get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions.
It's not all that useful for a "write a whole driver in rust" type
of thing, but the firmware bindings do help out the phy rust
drivers, and the driver core bindings give a solid base on which
others can start their work.
There is still a long way to go here before we have a multitude of
rust drivers being added, but it's a great first step.
- driver core const api changes.
This reached across all bus types, and there are some fix-ups for
some not-common bus types that linux-next and 0-day testing shook
out.
This work is being done to help make the rust bindings more safe,
as well as the C code, moving toward the end-goal of allowing us to
put driver structures into read-only memory. We aren't there yet,
but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
ARM: sa1100: make match function take a const pointer
sysfs/cpu: Make crash_hotplug attribute world-readable
dio: Have dio_bus_match() callback take a const *
zorro: make match function take a const pointer
driver core: module: make module_[add|remove]_driver take a const *
driver core: make driver_find_device() take a const *
driver core: make driver_[create|remove]_file take a const *
firmware_loader: fix soundness issue in `request_internal`
firmware_loader: annotate doctests as `no_run`
devres: Correct code style for functions that return a pointer type
devres: Initialize an uninitialized struct member
devres: Fix memory leakage caused by driver API devm_free_percpu()
devres: Fix devm_krealloc() wasting memory
driver core: platform: Switch to use kmemdup_array()
driver core: have match() callback in struct bus_type take a const *
MAINTAINERS: add Rust device abstractions to DRIVER CORE
device: rust: improve safety comments
MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer
MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER
firmware: rust: improve safety comments
...
|
|
In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change the API to select MAC default time stamping instead of the PHY.
Indeed the PHY is closer to the wire therefore theoretically it has less
delay than the MAC timestamping but the reality is different. Due to lower
time stamping clock frequency, latency in the MDIO bus and no PHC hardware
synchronization between different PHY, the PHY PTP is often less precise
than the MAC. The exception is for PHY designed specially for PTP case but
these devices are not very widespread. For not breaking the compatibility
default_timestamp flag has been introduced in phy_device that is set by
the phy driver to know we are using the old API behavior.
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-4-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/phy/aquantia/aquantia.h
219343755eae ("net: phy: aquantia: add missing include guards")
61578f679378 ("net: phy: aquantia: add support for PHY LEDs")
drivers/net/ethernet/wangxun/libwx/wx_hw.c
bd07a9817846 ("net: txgbe: remove separate irq request for MSI and INTx")
b501d261a5b3 ("net: txgbe: add FDIR ATR support")
https://lore.kernel.org/all/20240703112936.483c1975@canb.auug.org.au/
include/linux/mlx5/mlx5_ifc.h
048a403648fc ("net/mlx5: IFC updates for changing max EQs")
99be56171fa9 ("net/mlx5e: SHAMPO, Re-enable HW-GRO")
https://lore.kernel.org/all/20240701133951.6926b2e3@canb.auug.org.au/
Adjacent changes:
drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
4130c67cd123 ("wifi: iwlwifi: mvm: check vif for NULL/ERR_PTR before dereference")
3f3126515fbe ("wifi: iwlwifi: mvm: add mvm-specific guard")
include/net/mac80211.h
816c6bec09ed ("wifi: mac80211: fix BSS_CHANGED_UNSOL_BCAST_PROBE_RESP")
5a009b42e041 ("wifi: mac80211: track changes in AP's TPE")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the match() callback, the struct device_driver * should not be
changed, so change the function callback to be a const *. This is one
step of many towards making the driver core safe to have struct
device_driver in read-only memory.
Because the match() callback is in all busses, all busses are modified
to handle this properly. This does entail switching some container_of()
calls to container_of_const() to properly handle the constant *.
For some busses, like PCI and USB and HV, the const * is cast away in
the match callback as those busses do want to modify those structures at
this point in time (they have a local lock in the driver structure.)
That will have to be changed in the future if they wish to have their
struct device * in read-only-memory.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Alex Elder <elder@kernel.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/2024070136-wrongdoer-busily-01e8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix copy-paste error in the code comment. The code refers to
LED blinking configuration, not brightness configuration. It
was likely copied from comment above this one which does
refer to brightness configuration.
Fixes: 4e901018432e ("net: phy: phy_device: Call into the PHY driver to set LED blinking")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240626030638.512069-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
10G-QXGMII is a MAC-to-PHY interface defined by the USXGMII multiport
specification. It uses the same signaling as USXGMII, but it multiplexes
4 ports over the link, resulting in a maximum speed of 2.5G per port.
Some in-tree SoCs like the NXP LS1028A use "usxgmii" when they mean
either the single-port USXGMII or the quad-port 10G-QXGMII variant, and
they could get away just fine with that thus far. But there is a need to
distinguish between the 2 as far as SerDes drivers are concerned.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The series is causing issues with PHY drivers built as modules.
Since it was only partially applied and the merge window has
opened let's revert and try again for v6.11.
Revert 6916e461e793 ("net: phy: Introduce ethernet link topology representation")
Revert 0ec5ed6c130e ("net: sfp: pass the phy_device when disconnecting an sfp module's PHY")
Revert e75e4e074c44 ("net: phy: add helpers to handle sfp phy connect/disconnect")
Revert fdd353965b52 ("net: sfp: Add helper to return the SFP bus name")
Revert 841942bc6212 ("net: ethtool: Allow passing a phy index for some commands")
Link: https://lore.kernel.org/all/171242462917.4000.9759453824684907063.git-patchwork-notify@kernel.org/
Link: https://lore.kernel.org/all/20240507102822.2023826-1-maxime.chevallier@bootlin.com/
Link: https://lore.kernel.org/r/20240513154156.104281-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are a few PHY drivers that can handle SFP modules through their
sfp_upstream_ops. Introduce Phylib helpers to keep track of connected
SFP PHYs in a netdevice's namespace, by adding the SFP PHY to the
upstream PHY's netdev's namespace.
By doing so, these SFP PHYs can be enumerated and exposed to users,
which will be able to use their capabilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to. The PHY index can be
re-used for PHYs that are persistent.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some MAC controllers (e.g. stmmac) require their connected PHY to
continuously provide a receive clock signal. This can cause issues in two
cases:
1. The clock signal hasn't been started yet by the time the MAC driver
initializes its hardware. This can make the initialization fail, as in
the case of the rzn1 GMAC1 driver.
2. The clock signal is cut during a power saving event. By the time the
MAC is brought back up, the clock signal is still not active since
phylink_start hasn't been called yet. This brings us back to case 1.
If a PHY driver reads this flag, it should ensure that the receive clock
signal is started as soon as possible, and that it isn't brought down when
the PHY goes into suspend.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[rgantois: commit log]
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-1-24a74e5c761f@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In order for EEE to operate, both the MAC and the PHY need to support
it, similar to how pause works. With some exception - a number of PHYs
have SmartEEE or AutoGrEEEn support in order to provide some EEE-like
power savings with non-EEE capable MACs.
Copy the pause concept and add the call phy_support_eee() which the MAC
makes after connecting the PHY to indicate it supports EEE. phylib will
then advertise EEE when auto-neg is performed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Have phylib keep track of the EEE configuration. This simplifies the
MAC drivers, in that they don't need to store it.
Future patches to phylib will also make use of this information to
further simplify the MAC drivers.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MAC drivers which support EEE need to know the results of the EEE
auto-neg in order to program the hardware to perform EEE or not. The
oddly named phy_init_eee() can be used to determine this, it returns 0
if EEE should be used, or a negative error code,
e.g. -EOPPROTONOTSUPPORT if the PHY does not support EEE or negotiate
resulted in it not being used.
However, many MAC drivers get this wrong. Add phydev->enable_tx_lpi
which indicates the result of the autoneg for EEE, including if EEE is
administratively disabled with ethtool. The MAC driver can then access
this in the same way as link speed and duplex in the adjust link
callback. If enable_tx_lpi is true, the MAC should send low power
indications and does not need to consider anything else with respect
to EEE.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As a prerequisite for adding EEE CAP2 register support, complement
PHY_EEE_CAP1_FEATURES with PHY_EEE_CAP2_FEATURES.
For now only 2500baseT and 5000baseT modes are supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit d492cc2573a0 ("driver core: device.h: make struct
bus_type a const *"), the driver core can properly handle constant
struct bus_type, move the mdio_bus_type variable to be a constant
structure as well, placing it into read-only memory which can not be
modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240213-bus_cleanup-mdio-v1-1-f9e799da7fda@marliere.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Some PHY driver might require additional regs call after
genphy_c37_read_status() is called.
Expand genphy_c37_read_status to provide a bool wheather the link has
changed or not to permit PHY driver to skip additional regs call if
nothing has changed.
Every user of genphy_c37_read_status() is updated with the new
additional bool.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devm/of_phy_package_join helper to join PHYs in a PHY package. These
are variant of the manual phy_package_join with the difference that
these will use DT nodes to derive the base_addr instead of manually
passing an hardcoded value.
An additional value is added in phy_package_shared, "np" to reference
the PHY package node pointer in specific PHY driver probe_once and
config_init_once functions to make use of additional specific properties
defined in the PHY package node in DT.
The np value is filled only with of_phy_package_join if a valid PHY
package node is found. A valid PHY package node must have the node name
set to "ethernet-phy-package".
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Per default phylib preserves the EEE advertising at the time of
phy probing. The EEE advertising can be changed from user space,
in addition this helper allows to set the EEE advertising to all
supported modes from drivers in kernel space.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20bfc471-aeeb-4ae4-ba09-7d6d4be6b86a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Device driver structures are shared between all devices that they
match, and thus nothing should never write to the device driver
structure through the phydev->drv pointer. Let's make this pointer
const to catch code that attempts to do so.
Suggested-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1rVxXt-002YqY-9G@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
side
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for PHY LEDs polarity modes. Some PHY require LED to be set
to active low to be turned ON. Adds support for this by declaring
active-low property in DT.
PHY driver needs to declare .led_polarity_set() to configure LED
polarity modes. Function will pass the index with the LED index and a
bitmap with all the required modes to set.
Current supported modes are:
- active-low with the flag PHY_LED_ACTIVE_LOW. LED is set to active-low
to turn it ON.
- inactive-high-impedance with the flag PHY_LED_INACTIVE_HIGH_IMPEDANCE.
LED is set to high impedance to turn it OFF.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240125203702.4552-4-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
e009b2efb7a8 ("bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()")
0f2b21477988 ("bnxt_en: Fix compile error without CONFIG_RFS_ACCEL")
https://lore.kernel.org/all/20240105115509.225aa8a2@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 32bb4515e34469975abc936deb0a116c4a445817.
This reverts commit d078d480639a4f3b5fc2d56247afa38e0956483a.
This reverts commit fcc4b105caa4b844bf043375bf799c20a9c99db1.
This reverts commit 345237dbc1bdbb274c9fb9ec38976261ff4a40b8.
This reverts commit 7db69ec9cfb8b4ab50420262631fb2d1908b25bf.
This reverts commit 95132a018f00f5dad38bdcfd4180d1af955d46f6.
This reverts commit 63d5eaf35ac36cad00cfb3809d794ef0078c822b.
This reverts commit c29451aefcb42359905d18678de38e52eccb3bb5.
This reverts commit 2ab0edb505faa9ac90dee1732571390f074e8113.
This reverts commit dedd702a35793ab462fce4c737eeba0badf9718e.
This reverts commit 034fcc210349b873ece7356905be5c6ca11eef2a.
This reverts commit 9c5625f559ad6fe9f6f733c11475bf470e637d34.
This reverts commit 02018c544ef113e980a2349eba89003d6f399d22.
Looks like we need more time for reviews, and incremental
changes will be hard to make sense of. So revert.
Link: https://lore.kernel.org/all/ZZP6FV5sXEf+xd58@shell.armlinux.org.uk/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit cff9c565e65f3622e8dc1dcc21c1520a083dff35.
Revert based on feedback from Russell.
Link: https://lore.kernel.org/all/ZZPtUIRerqTI2%2Fyh@shell.armlinux.org.uk/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the @phy_timer: line to prevent the kernel-doc warning:
include/linux/phy.h:768: warning: Excess struct member 'phy_timer' description in 'phy_device'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: netdev@vger.kernel.org
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a few PHY drivers that can handle SFP modules through their
sfp_upstream_ops. Introduce Phylib helpers to keep track of connected
SFP PHYs in a netdevice's namespace, by adding the SFP PHY to the
upstream PHY's netdev's namespace.
By doing so, these SFP PHYs can be enumerated and exposed to users,
which will be able to use their capabilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The __of_mdiobus_register() function was storing the device node in
dev.of_node without increasing its reference count. It implicitly relied
on the caller to maintain the allocated node until the mdiobus was
unregistered.
Now, __of_mdiobus_register() will acquire the node before assigning it,
and of_mdiobus_unregister_callback() will be called at the end of
mdio_unregister().
Drivers can now release the node immediately after MDIO registration.
Some of them are already doing that even before this patch.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHY in PHY package may require to read/write MMD regs to correctly
configure the PHY package.
Add support for these additional required function in both lock and no
lock variant.
It's assumed that the entire PHY package is either C22 or C45. We use
C22 or C45 way of writing/reading to mmd regs based on the passed phydev
whether it's C22 or C45.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current API for PHY package are limited to single address to configure
global settings for the PHY package.
It was found that some PHY package (for example the qca807x, a PHY
package that is shipped with a bundle of 5 PHY) requires multiple PHY
address to configure global settings. An example scenario is a PHY that
have a dedicated PHY for PSGMII/serdes calibrarion and have a specific
PHY in the package where the global PHY mode is set and affects every
other PHY in the package.
Change the API in the following way:
- Change phy_package_join() to take the base addr of the PHY package
instead of the global PHY addr.
- Make __/phy_package_write/read() require an additional arg that
select what global PHY address to use by passing the offset from the
base addr passed on phy_package_join().
Each user of this API is updated to follow this new implementation
following a pattern where an enum is defined to declare the offset of the
addr.
We also drop the check if shared is defined as any user of the
phy_package_read/write is expected to use phy_package_join first. Misuse
of this will correctly trigger a kernel panic for NULL pointer
exception.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch addr type in phy_package_shared struct to u8.
The value is already checked to be non negative and to be less than
PHY_MAX_ADDR, hence u8 is better suited than using int.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move part of the genphy_c45_pma_read_abilities() code to a separate
function.
Some PHYs do not implement PMA/PMD status 2 register (Register 1.8) but
do implement PMA/PMD extended ability register (Register 1.11). To make
use of it, we need to be able to access this part of code separately.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231212054144.87527-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a possible_interfaces member to struct phy_device to indicate which
interfaces a clause 45 PHY may switch between depending on the media.
This must be populated by the PHY driver by the time the .config_init()
method completes according to the PHYs host-side configuration.
For example, the Marvell 88x3310 PHY can switch between 10GBASE-R,
5GBASE-R, 2500BASE-X, and SGMII on the host side depending on the media
side speed, so all these interface modes are set in the
possible_interfaces member.
This allows phylib users (such as phylink) to know in advance which
interface modes to expect, which allows them to appropriately restrict
the advertised link modes according to the capabilities of other parts
of the link.
Tested-by: Luo Jie <quic_luoj@quicinc.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1r6VHk-00DDLN-I7@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Revert following commits:
commit acec05fb78ab ("net_tstamp: Add TIMESTAMPING SOFTWARE and HARDWARE mask")
commit 11d55be06df0 ("net: ethtool: Add a command to expose current time stamping layer")
commit bb8645b00ced ("netlink: specs: Introduce new netlink command to get current timestamp")
commit d905f9c75329 ("net: ethtool: Add a command to list available time stamping layers")
commit aed5004ee7a0 ("netlink: specs: Introduce new netlink command to list available time stamping layers")
commit 51bdf3165f01 ("net: Replace hwtstamp_source by timestamping layer")
commit 0f7f463d4821 ("net: Change the API of PHY default timestamp to MAC")
commit 091fab122869 ("net: ethtool: ts: Update GET_TS to reply the current selected timestamp")
commit 152c75e1d002 ("net: ethtool: ts: Let the active time stamping layer be selectable")
commit ee60ea6be0d3 ("netlink: specs: Introduce time stamping set command")
They need more time for reviews.
Link: https://lore.kernel.org/all/20231118183529.6e67100c@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change the API to select MAC default time stamping instead of the PHY.
Indeed the PHY is closer to the wire therefore theoretically it has less
delay than the MAC timestamping but the reality is different. Due to lower
time stamping clock frequency, latency in the MDIO bus and no PHC hardware
synchronization between different PHY, the PHY PTP is often less precise
than the MAC. The exception is for PHY designed specially for PTP case but
these devices are not very widespread. For not breaking the compatibility I
introduce a default_timestamp flag in phy_device that is set by the phy
driver to know we are using the old API behavior.
The phy_set_timestamp function is called at each call of phy_attach_direct.
In case of MAC driver using phylink this function is called when the
interface is turned up. Then if the interface goes down and up again the
last choice of timestamp will be overwritten by the default choice.
A solution could be to cache the timestamp status but it can bring other
issues. In case of SFP, if we change the module, it doesn't make sense to
blindly re-set the timestamp back to PHY, if the new module has a PHY with
mediocre timestamping capabilities.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHYs hwtstamp callback are still getting the timestamp config from
ifreq and using copy_from/to_user.
Get rid of these functions by using timestamp configuration in parameter.
This also allow to move on to kernel_hwtstamp_config and be similar to
net devices using the new ndo_hwstamp_get/set.
This adds the possibility to manipulate the timestamp configuration
from the kernel which was not possible with the copy_from/to_user.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
