| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add routines for manipulating TLS TX offload contexts.
In Innova TLS, TLS contexts are added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.
Add implementation for Innova TLS (FPGA-based) hardware.
These routines will be used by the TLS offload support in a later patch
mlx5/accel is a middle acceleration layer to allow mlx5e and other ULPs
to work directly with mlx5_core rather than Innova FPGA or other mlx5
acceleration providers.
In the future, when IPSec/TLS or any other acceleration gets integrated
into ConnectX chip, mlx5/accel layer will provide the integrated
acceleration, rather than the Innova one.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"Doug and I are at a conference next week so if another PR is sent I
expect it to only be bug fixes. Parav noted yesterday that there are
some fringe case behavior changes in his work that he would like to
fix, and I see that Intel has a number of rc looking patches for HFI1
they posted yesterday.
Parav is again the biggest contributor by patch count with his ongoing
work to enable container support in the RDMA stack, followed by Leon
doing syzkaller inspired cleanups, though most of the actual fixing
went to RC.
There is one uncomfortable series here fixing the user ABI to actually
work as intended in 32 bit mode. There are lots of notes in the commit
messages, but the basic summary is we don't think there is an actual
32 bit kernel user of drivers/infiniband for several good reasons.
However we are seeing people want to use a 32 bit user space with 64
bit kernel, which didn't completely work today. So in fixing it we
required a 32 bit rxe user to upgrade their userspace. rxe users are
still already quite rare and we think a 32 bit one is non-existing.
- Fix RDMA uapi headers to actually compile in userspace and be more
complete
- Three shared with netdev pull requests from Mellanox:
* 7 patches, mostly to net with 1 IB related one at the back).
This series addresses an IRQ performance issue (patch 1),
cleanups related to the fix for the IRQ performance problem
(patches 2-6), and then extends the fragmented completion queue
support that already exists in the net side of the driver to the
ib side of the driver (patch 7).
* Mostly IB, with 5 patches to net that are needed to support the
remaining 10 patches to the IB subsystem. This series extends
the current 'representor' framework when the mlx5 driver is in
switchdev mode from being a netdev only construct to being a
netdev/IB dev construct. The IB dev is limited to raw Eth queue
pairs only, but by having an IB dev of this type attached to the
representor for a switchdev port, it enables DPDK to work on the
switchdev device.
* All net related, but needed as infrastructure for the rdma
driver
- Updates for the hns, i40iw, bnxt_re, cxgb3, cxgb4, hns drivers
- SRP performance updates
- IB uverbs write path cleanup patch series from Leon
- Add RDMA_CM support to ib_srpt. This is disabled by default. Users
need to set the port for ib_srpt to listen on in configfs in order
for it to be enabled
(/sys/kernel/config/target/srpt/discovery_auth/rdma_cm_port)
- TSO and Scatter FCS support in mlx4
- Refactor of modify_qp routine to resolve problems seen while
working on new code that is forthcoming
- More refactoring and updates of RDMA CM for containers support from
Parav
- mlx5 'fine grained packet pacing', 'ipsec offload' and 'device
memory' user API features
- Infrastructure updates for the new IOCTL interface, based on
increased usage
- ABI compatibility bug fixes to fully support 32 bit userspace on 64
bit kernel as was originally intended. See the commit messages for
extensive details
- Syzkaller bugs and code cleanups motivated by them"
* tag 'for-linus-unmerged' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (199 commits)
IB/rxe: Fix for oops in rxe_register_device on ppc64le arch
IB/mlx5: Device memory mr registration support
net/mlx5: Mkey creation command adjustments
IB/mlx5: Device memory support in mlx5_ib
net/mlx5: Query device memory capabilities
IB/uverbs: Add device memory registration ioctl support
IB/uverbs: Add alloc/free dm uverbs ioctl support
IB/uverbs: Add device memory capabilities reporting
IB/uverbs: Expose device memory capabilities to user
RDMA/qedr: Fix wmb usage in qedr
IB/rxe: Removed GID add/del dummy routines
RDMA/qedr: Zero stack memory before copying to user space
IB/mlx5: Add ability to hash by IPSEC_SPI when creating a TIR
IB/mlx5: Add information for querying IPsec capabilities
IB/mlx5: Add IPsec support for egress and ingress
{net,IB}/mlx5: Add ipsec helper
IB/mlx5: Add modify_flow_action_esp verb
IB/mlx5: Add implementation for create and destroy action_xfrm
IB/uverbs: Introduce ESP steering match filter
IB/uverbs: Add modify ESP flow_action
...
|
|
This change updates the mlx5 interface to create mkey
on the device.
The updates in the command mailbox include increasing the
access mode type field to 5 bits in order to support additional
types such as MLX5_MKC_ACCESS_MODE_MEMIC which represents device
memory access type and will be used when registering MR on allocated
device memory.
All the places that use the old access mode format are adjusted as
well.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This patch adds the mlx5_ib driver implementation for the device
memory allocation API.
It implements the ib_device callbacks for allocation and deallocation
operations as well as a new mmap command support which allows mapping
an allocated device memory to a VMA.
The change also adds reporting of device memory maximum size and
alignment parameters reported in device capabilities.
The allocation/deallocation operations are using new firmware
commands to allocate MEMIC memory on the device.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This patch adds querying of device memory capabilities by the mlx5_core
driver during initialization.
Device memory capabilities is a new capability type and structure
which contains the necessary data that is needed for future device
memory allocation.
The presence of this new capabilities struct is indicated in the
general capabilities struct which is queried first by the driver.
If the presence bit is set, the driver will also query the new
capabilities struct and save it in the device context.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Current Striding RQ HW feature utilizes the RX buffers so that
there is no wasted room between the strides. This maximises
the memory utilization.
This prevents the use of build_skb() (which requires headroom
and tailroom), and demands to memcpy the packets headers into
the skb linear part.
In this patch, whenever a set of conditions holds, we apply
an RQ configuration that allows combining the use of linear SKB
on top of a Striding RQ.
To use build_skb() with Striding RQ, the following must hold:
1. packet does not cross a page boundary.
2. there is enough headroom and tailroom surrounding the packet.
We can satisfy 1 and 2 by configuring:
stride size = MTU + headroom + tailoom.
This is possible only when:
a. (MTU - headroom - tailoom) does not exceed PAGE_SIZE.
b. HW LRO is turned off.
Using linear SKB has many advantages:
- Saves a memcpy of the headers.
- No page-boundary checks in datapath.
- No filler CQEs.
- Significantly smaller CQ.
- SKB data continuously resides in linear part, and not split to
small amount (linear part) and large amount (fragment).
This saves datapath cycles in driver and improves utilization
of SKB fragments in GRO.
- The fragments of a resulting GRO SKB follow the IP forwarding
assumption of equal-size fragments.
Some implementation details:
HW writes the packets to the beginning of a stride,
i.e. does not keep headroom. To overcome this we make sure we can
extend backwards and use the last bytes of stride i-1.
Extra care is needed for stride 0 as it has no preceding stride.
We make sure headroom bytes are available by shifting the buffer
pointer passed to HW by headroom bytes.
This configuration now becomes default, whenever capable.
Of course, this implies turning LRO off.
Performance testing:
ConnectX-5, single core, single RX ring, default MTU.
UDP packet rate, early drop in TC layer:
--------------------------------------------
| pkt size | before | after | ratio |
--------------------------------------------
| 1500byte | 4.65 Mpps | 5.96 Mpps | 1.28x |
| 500byte | 5.23 Mpps | 5.97 Mpps | 1.14x |
| 64byte | 5.94 Mpps | 5.96 Mpps | 1.00x |
--------------------------------------------
TCP streams: ~20% gain
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In some firmware configuration, UMR usage from Virtual Functions is restricted.
This information is published to the driver using new capability bits.
Avoid using UMRs in these cases and use the Firmware slow-path flow to create
mkeys and populate them with Virtual to Physical address translation.
Older drivers that do not have this patch, will end up using memory keys that
aren't populated with Virtual to Physical address translation that is done
part of the UMR work.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Newer NICs (ConnectX-5 and onward) can apply vlan pop or push as an
action taking place during flow steering. Add the core bits for that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Added the following packets dropped while vport down statistics:
Rx dropped while vport down - counts packets which were steered by
e-switch to a vport, but dropped since the vport was down. This counter
will be shown on ip link tool as part of the vport rx_dropped counter.
Tx dropped while vport down - counts packets which were transmitted by
a vport, but dropped due to vport logical link down. This counter
will be shown on ip link tool as part of the vport tx_dropped counter.
The counters are read from FW by command QUERY_VNIC_ENV.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Added the following packets drop counter:
Rx steering missed dropped packets - counts packets which were dropped
due to miss on NIC rx steering rules.
This counter will be shown on ethtool as a new counter called
rx_steer_missed_packets.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add support for new FW command QUERY_VNIC_ENV.
The command is used by the driver to query vnic diagnostic statistics
from FW.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Implement set/get functions to configure PFC stall prevention
timeout by tunables api through ethtool.
By default the stall prevention timeout is configured to 8 sec.
Timeout range is: 80-8000 msec.
Enabling stall prevention with the auto timeout will set
the timeout to 100 msec.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add the needed capability bit and counters to device spec description.
Expose the following two counters in ethtool:
tx_pause_storm_warning_events: when the device is stalled for a period
longer than a pre-configured watermark, the counter increase, allowing
the debug utility an insight into current device status.
tx_pause_storm_error_events: when the device is stalled for a period
longer than a pre-configured timeout, the pause transmission is disabled,
and the counter increase.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add two new parameters: max_burst_sz and typical_pkt_size (both
in bytes) to rate limit configurations.
max_burst_sz: The device will schedule bursts of packets for an
SQ connected to this rate, smaller than or equal to this value.
Value 0x0 indicates packet bursts will be limited to the device
defaults. This field should be used if bursts of packets must be
strictly kept under a certain value.
typical_pkt_size: When the rate limit is intended for a stream of
similar packets, stating the typical packet size can improve the
accuracy of the rate limiter. The expected packet size will be
the same for all SQs associated with the same rate limit index.
Ethernet driver is updated according to this change, but these two
parameters will be kept as 0 due to lacking of proper way to get the
configurations from user space which requires to change
ndo_set_tx_maxrate interface.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Add helper functions that check if a protocol is
part of a flow steering match criteria.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, we don't support egress flow steering namespace in mlx5
flow steering core implementation. However, when we want to encrypt
a packet, we model it as a flow steering rule in the egress path.
To overcome this, we add an empty egress namespace to flow steering.
This namespace is initialized only when ipsec support exists.
In the future, this will grow to a full blown full steering
implementation, resembling the ingress path.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
To resolve conflicts in:
drivers/infiniband/hw/mlx5/main.c
drivers/infiniband/hw/mlx5/qp.c
From patches merged into the -rc cycle. The conflict resolution matches
what linux-next has been carrying.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Allow to specify the size of the hairpin queues along with the
packet buffer data size from the core setup code.
If the driver doesn't provide this, the FW applies proper value that
matches the provided data size and a FW chosen RQ stride size.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The latest merge between net and net-next introduced a complier assert in
mlx5 driver. In hca_cap_bits older fields are kept along with newer
fields that should have replaced them.
Fixes: c02b3741eb99 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Overlapping changes all over.
The mini-qdisc bits were a little bit tricky, however.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are systems platform information management interfaces (such as
HOST2BMC) for which we cannot disable local loopback multicast traffic.
Separate disable_local_lb_mc and disable_local_lb_uc capability bits so
driver will not disable multicast loopback traffic if not supported.
(It is expected that Firmware will not set disable_local_lb_mc if
HOST2BMC is running for example.)
Function mlx5_nic_vport_update_local_lb will do best effort to
disable/enable UC/MC loopback traffic and return success only in case it
succeeded to changed all allowed by Firmware.
Adapt mlx5_ib and mlx5e to support the new cap bits.
Fixes: 2c43c5a036be ("net/mlx5e: Enable local loopback in loopback selftest")
Fixes: c85023e153e3 ("IB/mlx5: Add raw ethernet local loopback support")
Fixes: bded747bb432 ("net/mlx5: Add raw ethernet local loopback firmware command")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add hairpin definitions to the IFC file.
This includes the HCA ID, few HCA hairpin capabilities, new
fields in RQ/SQ used later for the pairing and the WQ hairpin
data size attribute.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When mlx5_ib_add is called determine if the mlx5 core device being
added is capable of dual port RoCE operation. If it is, determine
whether it is a master device or a slave device using the
num_vhca_ports and affiliate_nic_vport_criteria capabilities.
If the device is a slave, attempt to find a master device to affiliate it
with. Devices that can be affiliated will share a system image guid. If
none are found place it on a list of unaffiliated ports. If a master is
found bind the port to it by configuring the port affiliation in the NIC
vport context.
Similarly when mlx5_ib_remove is called determine the port type. If it's
a slave port, unaffiliate it from the master device, otherwise just
remove it from the unaffiliated port list.
The IB device is registered as a multiport device, even if a 2nd port is
not available for affiliation. When the 2nd port is affiliated later the
GID cache must be refreshed in order to get the default GIDs for the 2nd
port in the cache. Export roce_rescan_device to provide a mechanism to
refresh the cache after a new port is bound.
In a multiport configuration all IB object (QP, MR, PD, etc) related
commands should flow through the master mlx5_core_dev, other commands
must be sent to the slave port mlx5_core_mdev, an interface is provide
to get the correct mdev for non IB object commands.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Generate a unique 128bit identifier for each host and pass that value to
firmware in the INIT_HCA command if it reports the sw_owner_id
capability. Each device bound to the mlx5_core driver will have the same
software owner ID.
In subsequent patches mlx5_core devices will be bound via a new VPort
command so that they can operate together under a single InfiniBand
device. Only devices that have the same software owner ID can be bound,
to prevent traffic intended for one host arriving at another.
The INIT_HCA command length was expanded by 128 bits. The command
length is provided as an input FW commands. Older FW does not have a
problem receiving this command in the new longer form.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
In mlx5_ifc, struct size was not complete, and thus driver was sending
garbage after the last defined field. Fixed it by adding reserved field
to complete the struct size.
In addition, rename all set_rate_limit to set_pp_rate_limit to be
compliant with the Firmware <-> Driver definition.
Fixes: 7486216b3a0b ("{net,IB}/mlx5: mlx5_ifc updates")
Fixes: 1466cc5b23d1 ("net/mlx5: Rate limit tables support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a fairly plain pull request. Lots of driver updates across the
stack, a huge number of static analysis cleanups including a close to
50 patch series from Bart Van Assche, and a number of new features
inside the stack such as general CQ moderation support.
Nothing really stands out, but there might be a few conflicts as you
take things in. In particular, the cleanups touched some of the same
lines as the new timer_setup changes.
Everything in this pull request has been through 0day and at least two
days of linux-next (since Stephen doesn't necessarily flag new
errors/warnings until day2). A few more items (about 30 patches) from
Intel and Mellanox showed up on the list on Tuesday. I've excluded
those from this pull request, and I'm sure some of them qualify as
fixes suitable to send any time, but I still have to review them
fully. If they contain mostly fixes and little or no new development,
then I will probably send them through by the end of the week just to
get them out of the way.
There was a break in my acceptance of patches which coincides with the
computer problems I had, and then when I got things mostly back under
control I had a backlog of patches to process, which I did mostly last
Friday and Monday. So there is a larger number of patches processed in
that timeframe than I was striving for.
Summary:
- Add iWARP support to qedr driver
- Lots of misc fixes across subsystem
- Multiple update series to hns roce driver
- Multiple update series to hfi1 driver
- Updates to vnic driver
- Add kref to wait struct in cxgb4 driver
- Updates to i40iw driver
- Mellanox shared pull request
- timer_setup changes
- massive cleanup series from Bart Van Assche
- Two series of SRP/SRPT changes from Bart Van Assche
- Core updates from Mellanox
- i40iw updates
- IPoIB updates
- mlx5 updates
- mlx4 updates
- hns updates
- bnxt_re fixes
- PCI write padding support
- Sparse/Smatch/warning cleanups/fixes
- CQ moderation support
- SRQ support in vmw_pvrdma"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (296 commits)
RDMA/core: Rename kernel modify_cq to better describe its usage
IB/mlx5: Add CQ moderation capability to query_device
IB/mlx4: Add CQ moderation capability to query_device
IB/uverbs: Add CQ moderation capability to query_device
IB/mlx5: Exposing modify CQ callback to uverbs layer
IB/mlx4: Exposing modify CQ callback to uverbs layer
IB/uverbs: Allow CQ moderation with modify CQ
iw_cxgb4: atomically flush the qp
iw_cxgb4: only call the cq comp_handler when the cq is armed
iw_cxgb4: Fix possible circular dependency locking warning
RDMA/bnxt_re: report vlan_id and sl in qp1 recv completion
IB/core: Only maintain real QPs in the security lists
IB/ocrdma_hw: remove unnecessary code in ocrdma_mbx_dealloc_lkey
RDMA/core: Make function rdma_copy_addr return void
RDMA/vmw_pvrdma: Add shared receive queue support
RDMA/core: avoid uninitialized variable warning in create_udata
RDMA/bnxt_re: synchronize poll_cq and req_notify_cq verbs
RDMA/bnxt_re: Flush CQ notification Work Queue before destroying QP
RDMA/bnxt_re: Set QP state in case of response completion errors
RDMA/bnxt_re: Add memory barriers when processing CQ/EQ entries
...
|
|
The QPTS register allows changing the priority trust state between pcp and
dscp. Add support to get/set trust state from device. When the port is
in pcp/dscp trust state, packet is routed by hardware to matching priority
based on its pcp/dscp value respectively.
The QPDPM register allow channing the dscp to priority mapping. Add support
to get/set dscp to priority mapping from device.
Note that to change a dscp mapping, the "e" bit of this dscp structure
must be set in the QPDPM firmware command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The QCAM register provides capability bit for all the QoS registers
using ACCESS_REG command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This patch updates the mlx5_ifc with the following:
- Fix tunnel_stateless_gre typo.
- max_geneve_opt_len - Maximum geneve options length.
- tunnel_stateless_geneve_rx - If set, receive Stateless
Offloads for Geneve tunneled (inner) packets are supported.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Adding new bits in mlx5_ifc_cmd_hca_cap to get the hardware capabilities
for:
- compression_128: Support 128B CQE compression
- cqe_128_always: Support 128B CQE padding
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Allow creation of a multi-packet receive queue.
In order to create a multi-packet RQ, the following fields in
the mlx5_ib_rwq should be set:
- log_num_strides: Log of number of strides per WQE
- single_stride_log_num_of_bytes: Log of a single stride size
- two_byte_shift_en: When enabled, hardware pads 2 bytes of zeros
before writing the message to memory (e.g. for the IP alignment).
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Added check for the maximal number of flow counters attached
to rule (FTE).
Fixes: bd5251dbf156b ('net/mlx5_core: Introduce flow steering destination of type counter')
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a big pull request.
Of note is that I'm sending you the new ioctl API for the rdma
subsystem. We put it up on linux-api@, but didn't get much response.
The API is complex, but it solves two different problems in one go:
1) The bi-directional nature of the RDMA file write calls, which
created the security hole we had to handle (and for which the fix
is now causing problems for systems in production, we were a bit
over zealous in the fix and the ability to open a device, then
fork, then create new queue pairs on the device and use them is
broken).
2) The bloat caused by different vendors implementing extensions to
the base verbs API. Each vendor's hardware is slightly different,
and the hardware might be suitable for one extension but not
another.
By the time we add generic extensions for all the different ways
that the different hardware can offload things, the API becomes
bloated. Things like our completion structs have started to exceed
a cache line in size because of all the elements needed to support
this. That in turn shows up heavily in the performance graphs with
a noticable drop in performance on 100Gigabit links as our
completion structs go from occupying one cache line to 1+.
This API makes things like the completion structs modular in a
very similar way to netlink so that your structs can only include
the items needed for the offloads/features you are actually using
on a given queue pair. In that way we support everything, but only
use what we need, and our structs stay smaller.
The ioctl API is better explained by the posting on linux-api@ than I
can explain it here, so I'll just leave it at that.
The rest of the pull request is typical stuff.
Updates for 4.14 kernel merge window
- Lots of hfi1 driver updates (mixed with a few qib and core updates
as well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so
we can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@"
* tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (328 commits)
IB/core: Expose ioctl interface through experimental Kconfig
IB/core: Assign root to all drivers
IB/core: Add completion queue (cq) object actions
IB/core: Add legacy driver's user-data
IB/core: Export ioctl enum types to user-space
IB/core: Explicitly destroy an object while keeping uobject
IB/core: Add macros for declaring methods and attributes
IB/core: Add uverbs merge trees functionality
IB/core: Add DEVICE object and root tree structure
IB/core: Declare an object instead of declaring only type attributes
IB/core: Add new ioctl interface
RDMA/vmw_pvrdma: Fix a signedness
RDMA/vmw_pvrdma: Report network header type in WC
IB/core: Add might_sleep() annotation to ib_init_ah_from_wc()
IB/cm: Fix sleeping in atomic when RoCE is used
IB/core: Add support to finalize objects in one transaction
IB/core: Add a generic way to execute an operation on a uobject
Documentation: Hardware tag matching
IB/mlx5: Support IB_SRQT_TM
net/mlx5: Add XRQ support
...
|
|
Add TX offloads support for GRE tunneled packets by reporting the needed
netdev features.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
* add offload_type field to mlx5_ifc_qpc_bits
* update mlx5_ifc_xrqc_bits layout
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Yossi Itigin <yosefe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Expose enhanced multi packet WQE capability to user space through
query_device by uhw.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Set the field to allow posting multi packet send WQEs if hardware
supports this feature. This doesn't mean the send WQEs will be for
multi packet unless the send WQE was prepared according to multi
packet send WQE format.
User space shall use flag MLX5_IB_ALLOW_MPW to check if hardware
supports MPW and allows MPW in SQ context.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Set underlay QPN as part of flow rule when it's applicable.
There is one root flow table in the NIC RX namespace and all the
underlay QPs steer the traffic to this flow table.
In order to prevent QP to get traffic which is not target to its
underlay QP, we need to set the underlay QP number as part of
the steering matching.
Note:
When multicast traffic is sent the QPN filtering is done by the firmware
as some early step. Adding the QPN match on the flow table entry is
wrong as by that time the target QPN holds the multicast address (e.g.
FF(s)) and it won't match.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add outbound_pci_buffer_overflow to ethtool output for monitoring the
number of packets that were dropped due to lack of PCIe buffers on
receive path from NIC port toward the host(s).
This counter is valid only in case that tx_overflow_buffer_pkt is
supported in MCAM enhanced features.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add capability bit in PCAM register and counters to PPCNT register.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add capability bit in MCAM register and counters to MPCNT register.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Read new NIC capability field which represnts 16 MSBs of the max flow
counters number supported (max_flow_counter_31_16).
Backward compatibility with older firmware is preserved, the modified
driver reads max_flow_counter_31_16 as 0 from the older firmware and
uses up to 64K counters.
Changed flow counter id from 16 bits to 32 bits. Backward compatibility
with older firmware is preserved as we kept the 16 LSBs of the counter
id in place and added 16 MSBs from reserved field.
Changed the background bulk reading of flow counters to work in chunks
of at most 32K counters, to make sure we don't attempt to allocate very
large buffers.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The counter list hardware structure doesn't contain a clear and
num_of_counters fields, remove them.
These wrong fields were never used by the driver hence no other driver
changes.
Fixes: a351a1b03bf1 ("net/mlx5: Introduce bulk reading of flow counters")
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to mark relevant fields while setting the MTPPS register
add field select. Otherwise it can cause a misconfiguration in
firmware.
Fixes: ee7f12205abc ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix miscalculation in reserved_at_1a0 field.
Fixes: ee7f12205abc ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This patch adds below requester and responder side error counters,
which will be exposed by hardware counters interface and are supported
as part of query Q counters command extension.
+---------------------------+-------------------------------------+
| Name | Description |
|---------------------------+-------------------------------------|
|resp_local_length_error | Number of times responder detected |
| | local length errors |
|---------------------------+-------------------------------------|
|resp_cqe_error | Number of CQEs completed with error |
| | at responder |
|---------------------------+-------------------------------------|
|req_cqe_error | Number of CQEs completed with error |
| | at requester |
|---------------------------+-------------------------------------|
|req_remote_invalid_request | Number of times requester detected |
| | remote invalid request error |
|---------------------------+-------------------------------------|
|req_remote_access_error | Number of times requester detected |
| | remote access error |
|---------------------------+-------------------------------------|
|resp_remote_access_error | Number of times responder detected |
| | remote access error |
|---------------------------+-------------------------------------|
|resp_cqe_flush_error | Number of CQEs completed with |
| | flushed with error at responder |
|---------------------------+-------------------------------------|
|req_cqe_flush_error | Number of CQEs completed with |
| | flushed with error at requester |
+---------------------------+-------------------------------------+
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
RQs that were configured for "delay drop" will prevent packet drops
when their WQEs are depleted.
Marking an RQ to be drop-less is done by setting delay_drop_en in RQ
context using CREATE_RQ command.
Since this feature is globally activated/deactivated by using the
SET_DELAY_DROP command on all the marked RQs, we activated/deactivated
it according to the number of RQs with 'delay_drop' enabled.
When timeout is expired, then the feature is deactivated. Therefore
the driver handles the delay drop timeout event and reactivate it.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When delay drop timeout is expired, the firmware raises
general notification event of DELAY_DROP_TIMEOUT subtype.
In addition the feature is disable so the driver have to
reactivate the timeout.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
