summaryrefslogtreecommitdiff
path: root/include/linux/micrel_phy.h
AgeCommit message (Collapse)AuthorFilesLines
2023-02-08net: micrel: Add support for lan8841 PHYHoratiu Vultur1-0/+1
The LAN8841 is completely integrated triple-speed (10BASE-T/ 100BASE-TX/ 1000BASE-T) Ethernet physical layer transceivers for transmission and reception of data on standard CAT-5, as well as CAT-5e and CAT-6, unshielded twisted pair (UTP) cables. The LAN8841 offers the industry-standard GMII/MII as well as the RGMII. Some of the features of the PHY are: - Wake on LAN - Auto-MDIX - IEEE 1588-2008 (V2) - LinkMD Capable diagnosis Currently the patch offers support only for link configuration. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-01-19net: mdio: Add workaround for Micrel PHYs which are not C45 compatibleAndrew Lunn1-0/+2
After scanning the bus for C22 devices, check if any Micrel PHYs have been found. They are known to do bad things if there are C45 transactions on the bus. Prevent the scanning of the bus using C45 if such a PHY has been detected. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2021-09-29net: phy: micrel: Add support for LAN8804 PHYHoratiu Vultur1-0/+1
The LAN8804 PHY has same features as that of LAN8814 PHY except that it doesn't support 1588, SyncE or Q-USGMII. This PHY is found inside the LAN966X switches. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-14net: phy: micrel: ksz886x/ksz8081: add cabletest supportOleksij Rempel1-0/+1
This patch support for cable test for the ksz886x switches and the ksz8081 PHY. The patch was tested on a KSZ8873RLL switch with following results: - port 1: - provides invalid values, thus return -ENOTSUPP (Errata: DS80000830A: "LinkMD does not work on Port 1", http://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8873-Errata-DS80000830A.pdf) - port 2: - can detect distance - can detect open on each wire of pair A (wire 1 and 2) - can detect open only on one wire of pair B (only wire 3) - can detect short between wires of a pair (wires 1 + 2 or 3 + 6) - short between pairs is detected as open. For example short between wires 2 + 3 is detected as open. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-14net: phy/dsa micrel/ksz886x add MDI-X supportOleksij Rempel1-0/+2
Add support for MDI-X status and configuration Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-14net: phy: micrel: move phy reg offsets to common headerMichael Grzeschik1-0/+13
Some micrel devices share the same PHY register defines. This patch moves them to one common header so other drivers can reuse them. And reuse generic MII_* defines where possible. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-12net: phy: mchp: Add support for LAN8814 QUAD PHYDivya Koppera1-0/+1
LAN8814 is a low-power, quad-port triple-speed (10BASE-T/100BASETX/1000BASE-T) Ethernet physical layer transceiver (PHY). It supports transmission and reception of data on standard CAT-5, as well as CAT-5e and CAT-6, unshielded twisted pair (UTP) cables. LAN8814 supports industry-standard QSGMII (Quad Serial Gigabit Media Independent Interface) and Q-USGMII (Quad Universal Serial Gigabit Media Independent Interface) providing chip-to-chip connection to four Gigabit Ethernet MACs using a single serialized link (differential pair) in each direction. The LAN8814 SKU supports high-accuracy timestamping functions to support IEEE-1588 solutions using Microchip Ethernet switches, as well as customer solutions based on SoCs and FPGAs. The LAN8804 SKU has same features as that of LAN8814 SKU except that it does not support 1588, SyncE, or Q-USGMII with PCH/MCH. This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T, QSGMII link with the MAC. Signed-off-by: Divya Koppera<divya.koppera@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-18net: phy: micrel: Update KSZ87xx PHY nameMarek Vasut1-1/+1
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches. Update the PHY ID and name to reflect that, as this family of switches is commonly refered to as KSZ87xx Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: David S. Miller <davem@davemloft.net> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: George McCollister <george.mccollister@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Cc: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152Thomas Gleixner1-6/+1
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-20net: phy: micrel: add Microchip KSZ9131 initial driverYuiko Oshino1-0/+1
Add support for Microchip Technology KSZ9131 10/100/1000 Ethernet PHY Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-01phy: micrel: add Microchip KSZ 9477 Switch PHY supportWoojung Huh1-0/+2
Adding Microchip 9477 Phy included in KSZ9477 Switch. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-27net: phy: micrel: add support for KSZ8795Sean Nyekjaer1-0/+2
This is adds support for the PHYs in the KSZ8795 5port managed switch. It will allow to detect the link between the switch and the soc and uses the same read_status functions as the KSZ8873MLL switch. Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-15net: phy: micrel: Add KSZ8041FTL fiber mode supportPhilipp Zabel1-0/+1
We can't detect the FXEN (fiber mode) bootstrap pin, so configure it via a boolean device tree property "micrel,fiber-mode". If it is enabled, auto-negotiation is not supported. The only available modes are 100base-fx (full duplex and half duplex). Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-21net: phy: micrel: add generic clock-mode-select supportJohan Hovold1-1/+0
Add generic RMII-Reference-Clock-Select support. Several Micrel PHY have an RMII-Reference-Clock-Select bit to select 25 MHz or 50 MHz clock mode. Recently, support for configuring this through device tree for KSZ8021 and KSZ8031 was added. Generalise this support so that it can be configured for other PHY types as well. Note that some PHY revisions (of the same type) has this bit inverted. This should be either configurable through a new device-tree property, or preferably, determined based on PHY ID if possible. Also note that this removes support for setting 25 MHz mode from board files which was also added by the above mentioned commit 45f56cb82e45 ("net/phy: micrel: Add clock support for KSZ8021/KSZ8031"). Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10net/phy: micrel: Add clock support for KSZ8021/KSZ8031Sascha Hauer1-0/+1
The KSZ8021 and KSZ8031 support RMII reference input clocks of 25MHz and 50MHz. Both PHYs differ in the default frequency they expect after reset. If this differs from the actual input clock, then register 0x1f bit 7 must be changed. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-11micrel: add support for KSZ8041RNLISergei Shtylyov1-0/+2
Renesas R-Car development boards use KSZ8041RNLI PHY which for some reason has ID of 0x00221537 that is not documented for KSZ8041-family PHYs and does not match the documented ID of 0x0022151x (where 'x' is the revision). We have to add the new #define PHY_ID_* and new ksphy_driver[] entry, almost the same as KSZ8041 one, differing only in the 'phy_id' and 'name' fields. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-22phy: micrel: Add definitions for common Micrel PHY registersDinh Nguyen1-0/+6
Add defines for common Micrel PHY setups so that other platforms can use them. Update imx61 and sama5 hardware to use the micrel_phy.h PHY defines. Also add support for the KSZ9021RLRN PHY. Signed-off-by: Dinh Nguyen <dinguyen@altera.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: David S. Miller <davem@davemloft.net> CC: Andrew Victor <linux@maxim.org.za> CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Cc: netdev@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-03-12phy/micrel: Add support for KSZ8031Hector Palacios1-0/+1
Micrel PHY KSZ8031 is similar to KSZ8021 and also requires the special initialization of "Operation Mode Strap Override" in reg 0x16 introduced in 212ea99 (phy/micrel: Implement support for KSZ8021). Signed-off-by: Hector Palacios <hector.palacios@digi.com> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-29drivers/net/phy/micrel_phy: Add support for new PHYsDavid J. Choi1-1/+8
Summary of changes: .Newly added phys -KSZ8081/KSZ8091, which has some phy ids. -KSZ8061 -KSZ9031, which is Gigabit phy. -KSZ886X, which has a switch function. -KSZ8031, which has a same phy ids with KSZ8021. Signed-off-by: David J. Choi <david.choi@micrel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-23net: add micrel KSZ8873MLL switch supportJean-Christophe PLAGNIOL-VILLARD1-0/+1
this will allow to detect the link between the switch and the soc Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-24phy/micrel: Add missing header to micrel_phy.hMarek Vasut1-0/+12
The license header was missing in micrel_phy.h . This patch adds one. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David J. Choi <david.choi@micrel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-24phy/micrel: Rename KS80xx to KSZ80xxMarek Vasut1-3/+3
There is no such part as KS8001, KS8041 or KS8051. There are only KSZ8001, KSZ8041 and KSZ8051. Rename these parts as such to match the Micrel naming. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David J. Choi <david.choi@micrel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-24phy/micrel: Implement support for KSZ8021Marek Vasut1-0/+1
The KSZ8021 PHY was previously caught by KS8051, which is not correct. This PHY needs additional setup if it is strapped for address 0. In such case an reserved bit must be written in the 0x16, "Operation Mode Strap Override" register. According to the KS8051 datasheet, that bit means "PHY Address 0 in non-broadcast" and it indeed behaves as such on KSZ8021. The issue where the ethernet controller (Freescale FEC) did not communicate with network is fixed by writing this bit as 1. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David J. Choi <david.choi@micrel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-22phy/micrel: Fix ID of KSZ9021Nobuhiro Iwamatsu1-1/+1
Right ID of KSZ9021 is 0x00221610. Because lower 4bit is a revision number, it varies according to a chip. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Cc: David J. Choi <david.choi@micrel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-15phy/micrel: add ability to support 50MHz RMII clock on KZS8051RNLBaruch Siach1-0/+16
Platform code can now set the MICREL_PHY_50MHZ_CLK bit of dev_flags in a fixup routine (registered with phy_register_fixup_for_uid()), to make the KZS8051RNL PHY work with 50MHz RMII reference clock. Cc: David J. Choi <david.choi@micrel.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-29 03:47:59 +0300