| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We can't forward declare enums.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
|
|
As with the existing emulation this should not be used in production
systems but is useful for test purposes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The modern idiom is to use irq_domain to allocate interrupts. This is
useful partly to allow further infrastructure to be based on the domains
and partly because it makes it much easier to allocate virtual interrupts
to devices as we don't need to allocate a contiguous range of interrupt
numbers.
Convert the wm831x driver over to this infrastructure, using a legacy
IRQ mapping if an irq_base is specified in platform data and otherwise
using a linear mapping, always registering the interrupts even if they
won't ever be used. Only boards which need to use the GPIOs as
interrupts should need to use an irq_base.
This means that we can't use the MFD irq_base management since the
unless we're using an explicit irq_base from platform data we can't rely
on a linear mapping of interrupts. Instead we need to map things via
the irq_domain - provide a conveniencem function wm831x_irq() to save a
small amount of typing when doing so. Looking at this I couldn't clearly
see anything the MFD core could do to make this nicer.
Since we're not supporting device tree yet there's no meaningful
advantage if we don't do this conversion in one, the fact that the
interrupt resources are used for repeated IP blocks makes accessor
functions for the irq_domain more trouble to do than they're worth.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Thomas Weber <thomas@tweber.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
* 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits)
mfd: Fix missing abx500 header file updates
mfd: Add missing <linux/io.h> include to intel_msic
x86, mrst: add platform support for MSIC MFD driver
mfd: Expose TurnOnStatus in ab8500 sysfs
mfd: Remove support for early drop ab8500 chip
mfd: Add support for ab8500 v3.3
mfd: Add ab8500 interrupt disable hook
mfd: Convert db8500-prcmu panic() into pr_crit()
mfd: Refactor db8500-prcmu request_clock() function
mfd: Rename db8500-prcmu init function
mfd: Fix db5500-prcmu defines
mfd: db8500-prcmu voltage domain consumers additions
mfd: db8500-prcmu reset code retrieval
mfd: db8500-prcmu tweak for modem wakeup
mfd: Add db8500-pcmu watchdog accessor functions for watchdog
mfd: hwacc power state db8500-prcmu accessor
mfd: Add db8500-prcmu accessors for PLL and SGA clock
mfd: Move to the new db500 PRCMU API
mfd: Create a common interface for dbx500 PRCMU drivers
mfd: Initialize DB8500 PRCMU regs
...
Fix up trivial conflicts in
arch/arm/mach-imx/mach-mx31moboard.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-u300/include/mach/irqs.h
drivers/mfd/wm831x-spi.c
|
|
In order to ease system integration provide a simulation of active high
IRQs on the GPIOs by polling the GPIO status when an IRQ is generated.
This isn't ideal on several fronts and will miss initially active IRQs in
the current implementation but it should work well for most cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In systems where there is no hardware signal from the processor to the
PMIC to initiate the final power off sequence we must initiate the
shutdown with a register write to the PMIC. Support such systems in the
driver. Since this may prevent a full shutdown of the system platform
data is used to enable the feature.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In systems where there is no hardware signal from the processor to the
PMIC to initiate the final power off sequence we must initiate the
shutdown with a register write to the PMIC. Support such systems in the
driver. Since this may prevent a full shutdown of the system platform
data is used to enable the feature.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Factor out the register read/write code to use the register map API. We
still need some wm831x specific code and locking in place to check that
the user key is handled correctly but only on the write side, reads are
not affected by the key.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM831x AUXADC hardware can schedule multiple conversions at once,
allowing higher performance when more than one source is in use as we
can have the hardware start new conversions without having to wait for
a register write.
Take advantage of this in the interrupt driven case, maintaining a list of
callers that are waiting for AUXADC conversions and completing them all
simultaneously. The external interface of the AUXADC is not changed so
there will be limited use of the feature immediately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Ensure that there's no possibility of loosing an AUXADC interrupt by reading
the conversion result in the IRQ handler when using interrupts. Otherwise
it's possible that under very heavy load a new conversion could be initiated
before the acknowledgement for a previous interrupt has happened.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use irq_allocate_desc() to get the IRQ range, which turns into a noop on
non-sparse systems. Since all existing users are non-sparse there should
be no compatibility issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Allow platform data to flag the touchscreen as disabled so that if the
touch driver is built in we don't end up causing lots of work by spuriously
detecting touchscreen activity on systems where it isn't in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM831x IRQ set_type() operation is doing a direct register write when
called but since set_type() is called with the bus lock held this isn't
legal and could cause deadlocks in the IRQ core.
Fix this by posting the updates into an array and syncing in the
bus_sync_unlock() callback.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Allow the GPIO mode of WM831x devices to be configured using platform data.
Users may provide a table of GPIO register values in gpio_defaults[]. In
order to allow 0 to be set explicitly out of range values are accepted and
masked off, with a WM831X_GPIO_CONFIGURE define provided to set an out of
range value.
This can be used to configure higher numbered GPIOs or override values set
in OTP for GPIOs configured using OTP.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The last user was removed in the merge window.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wm831x-ts - move BTN_TOUCH reporting to data transfer
Input: wm831x-ts - allow IRQ flags to be specified
Input: wm831x-ts - fix races with IRQ management
|
|
This allows maximum flexibility for configuring the direct GPIO based
interrupts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
If a system contains multiple WM831x devices we need to pass a device
number through to the MFD so that we use unique device IDs when we
instantiate child devices. In order to get support for this into 2.6.39
add some platform data to support the configuration, but no implementation
as yet.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Provide platform data allowing the system to set the /IRQ pin into
CMOS mode rather than the default open drain. The default value of
this platform data reflects the default hardware configuration so
there should be no change to existing users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
|
|
Some of the WM831x series of PMICs from Wolfson Microelectronics include
a resistive touchscreen controller. Implement support for these controllers
within the input API.
Platform data is supported to allow configuration of system parameters such
as selection between four and five wire touchscreens and for specification
of optional direct to CPU IRQs for sample availability and for pen down.
Use of this feature for at least the data IRQ is strongly recommended.
Thanks to Julien Boibessot for extensive testing and detailed feedback.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Julien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The WM8326 is a high performance variant of the WM832x series with
no software visible differences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In preparation for the addition of SPI support for the WM831x move the I2C
specific code into a separate file with a separate Kconfig option so the
I2C support can be excluded from the build.
Also update the 1133-EV1 PMIC module support for SMDK6410 to use the new
symbol.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The charger interrupts on the WM831x are unconditionally a wake source
for the system. If the power driver is not able to monitor them (for
example, due to the IRQ line not having been wired up on the system)
then any charger interrupt will prevent the system suspending for any
meaningful amount of time since nothing will ack them.
Avoid this issue by manually acknowledging these interrupts when we
suspend the WM831x core device if they are masked. If software is
actually using the interrupts then they will be unmasked and this
change will have no effect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the status of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM831x interrupt infrastructure hooked
up.
Also reduce the timeout for completion of conversions to 5ms from
the previous 10ms, the lower timeout should be sufficient.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Revision B of the WM831x devices changes the sense of the tristate
bit for GPIO configuration, inverting it to become an enable instead.
Take account of this in the gpiolib driver.
A current sink regulation status bit has also been added in revision B,
add a flag indicating if it's present but don't use it yet.
This revision also adds an interrupt on key up for the ON pin event
which the existing code is able to take advantage of.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The BuckWise DC-DC convertors in WM831x devices support switching to
a second output voltage using the logic level on one of the device
pins. This is intended to allow rapid voltage switching for uses like
cpufreq, replacing the I2C or SPI write used to configure the voltage
of the regulator with a much faster GPIO status change.
This is implemented by keeping the DVS voltage configured as the
maximum voltage permitted for the regulator. If a request is made
for the maximum voltage then the GPIO is used to switch to the DVS
voltage, otherwise the normal ON voltage is updated and used. This
follows the idiom used by most cpufreq drivers, which drop the
minimum voltage as the core frequency is dropped but use a constant
maximum - raising the voltage should normally be fast, but lowering
it may be slower.
Configuration of the DVS MFP on the device should be done externally,
for example via OTP.
Support is present in the hardware for monitoring the status of the
transition using a second GPIO. This is not currently implemented
but platform data is provided for it - the driver currently assumes
that the device will be configured to transition immediately - but
platform data is provided to reduce merge issues once it is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Replace the wm831x-local IRQ infrastructure with genirq, allowing access
to the diagnostic infrastructure of genirq and allowing us to implement
interrupt support for the GPIOs. The switchover is done within the
wm831x specific IRQ API, further patches will convert the individual
drivers to use genirq directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM8320 is an integrated power management subsystem providing
voltage regulators, RTC, watchdog and other functionality. The
WM8320 is derived from the WM831x and therefore shares most of
the driver code with the WM831x.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This supports future devices with fewer GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
There was confusion between the array size and the highest ISEL
value possible.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: move leds-clevo-mail's probe function to .devinit.text
leds: Fix indentation in LEDS_LP3944 Kconfig entry
leds: Fix LED names
leds: Fix leds-pca9532 whitespace issues
leds: fix coding style in worker thread code for ledtrig-gpio.
leds: gpio-leds: fix typographics fault
leds: Add WM831x status LED driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
drivers/power/wm97xx_battery.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] sizeof cleanup
[WATCHDOG] wdt_pci: fix printk and variable type
[WATCHDOG] wdt_pci - use pci_request_region
[WATCHDOG] ar7_wdt: Fix error handling during probe.
[WATCHDOG] ar7_wdt: convert to become a platform driver
[WATCHDOG] fix book E watchdog to take WDIOC_SETTIMEOUT arg in seconds
[WATCHDOG] davinci: use clock framework for timer frequency
[WATCHDOG] Use DIV_ROUND_UP() macro in the coh901327 WDT
[WATCHDOG] Add support for WM831x watchdog
[WATCHDOG] Add watchdog driver for NUC900
[WATCHDOG] add SBC-FITPC2 watchdog driver
|
|
The WM831x series of devices provide a watchdog with configurable
behaviour on timer expiry.
Currently this driver support refreshes via a register or GPIO line and
autonomous refreshes from a hardware source (eg, a clock).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The WM831x series of devices provide three types of LDO:
- General purpose LDOs supporting voltages from 0.9-3.3V
- High performance analogue LDOs supporting voltages from 1-3.5V
- Very low power consumption LDOs intended to support always on
functionality.
This patch adds support for all three kinds of LDO. Each regulator
is probed as an individual platform device with resources used to
provide the register map location of the regulator. Mixed hardware
and software control of regulators is not current supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM831x series of devices all have 3 DC-DC buck convertors. This
driver implements software control for these regulators via the
regulator API. Use with split hardware/software control of individual
regulators is not supported, though regulators not controlled by
software may be controlled via the hardware control interfaces.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM831x series of PMICs support control of initial power on
through the ON pin on the device with soft control of the pin
at other times. Represent this to userspace as KEY_POWER.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add support for the GPIO pins on the WM831x. No direct support is
currently supplied for configuring non-gpiolib functionality such
as pull configuration and alternate functions, soft configuration
of these will be provided in a future patch.
Currently use of these pins as interrupts is not supported due to
the ongoing issues with generic irq not support interrupt controllers
on interrupt driven buses. Users can directly request the interrupts
with the wm831x-specific APIs currently provided if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The current settings which can be used with the WM831x current sinks
can't easily be mapped between register values and currents at run
time without a lookup table since the values scale logarithmically
to match the way the human eye interprets brightness. This lookup
table is inclided in the core since several drivers need to use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM831x series of devices use OTP (One Time Programmable, a type
of PROM) to store system configuration. At run time this data is
visible via registers.
Currently the only explicitly supported feature is that the unique
ID provided by every WM831x device is exported to user space via
sysfs. Other configuration data may be read by system-specific
code in the pre_init() and post_init() platform data operations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM831x backlight driver requires at least the specification of the
current sink to use and a maximum current to allow them to function and
will actively interfere with other users of the regulators it uses if
misconfigured so only register the subdevice for it if this platform
data has been supplied.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM831x contains an auxiliary ADC with a number of switchable
inputs which is used to monitor some of the voltages and
temperatures in the system and has some external inputs which can be
used for machine specific purposes. Provide an API allowing drivers
to read values from the ADC.
An internal reference voltage is provided to allow callibration of
the ADC. This is used to calibrate the device at startup.
The hardware also supports continuous readings and digital comparators.
These are not yet supported by the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM831x includes an interrupt controller managing interrupts for
the various functions on the chip. This patch adds support for the
core interrupt block on the device.
Ideally this would be supported by genirq, particularly for the
GPIOs, but currently genirq is unable to cope with controllers on
interrupt driven buses so we cut'n'paste the generic interface.
Once genirq is able to cope chips like this it should be a case
of filing the prefixes off the code and redoing wm831x-irq.c to
move over.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM831x series of devices are register compatible processor power
management subsystems, providing regulator and power path management
facilities along with other services like watchdog, RTC and touch
panel controllers.
This patch adds very basic support, providing basic single register
I2C access, handling of the security key and registration of the
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The WM831x devices feature two software controlled status LEDs with
hardware assisted blinking.
The device can also autonomously control the LEDs based on a selection
of sources. This can be configured at boot time using either platform
data or the chip OTP. A sysfs file in the style of that for triggers
allowing the control source to be configured at run time. Triggers
can't be used here since they can't depend on the implementation details
of a specific LED type.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
|
|
The WM831x PMICs provide power path management from three sources:
a wall supply, USB and a battery with integrated charger. They also
provide an additional backup supply with integrated for maintaining
always on functionality such as the RTC and monitoring of power
switches.
After some initial configuration at startup the device operates
autonomously, the driver simply provides reporting of the current
state.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
