| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
'alignment'"
This reverts commit 267b21d0bef8e67dbe6c591c9991444e58237ec9.
Turns out some DTs do depend on this behavior. Specifically, a
downstream Pixel 6 DT. Revert the change at least until we can decide if
the DT spec can be changed instead.
Cc: stable@vger.kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Keep user-forced connector status even if it cannot be programmed. Same
behavior as for the rest of the drivers.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250114100214.195386-1-tzimmermann@suse.de
|
|
After commit 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card
unless WOWL is used"), the wifi adapter by default is turned off on
suspend and then re-probed on resume.
This conflicts with some embedded boards that require to remain powered.
They will fail on resume with:
brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
ieee80211 phy1: brcmf_bus_started: failed: -110
ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
This commit checks for the Device Tree property 'cap-power-off-cards'.
If this property is not set, it means that we do not have the capability
to power off and should therefore remain powered.
Signed-off-by: Matthias Proske <email@matthias-proske.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20250212185941.146958-2-email@matthias-proske.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The encoder HW/SW state verification should use a SW state which stays
unchanged while the encoder/output is active. The intel_dp::is_mst flag
used during state computation to choose between the DP SST/MST modes can
change while the output is active, if the sink gets disconnected or the
MST topology is removed for another reason. A subsequent state
verification using intel_dp::is_mst leads then to a mismatch if the
output is disabled/re-enabled without recomputing its state.
Use the encoder's active MST link count instead, which will be always
non-zero for an active MST output and will be zero for SST.
Fixes: 35d2e4b75649 ("drm/i915/ddi: start distinguishing 128b/132b SST and MST at state readout")
Fixes: 40d489fac0e8 ("drm/i915/ddi: handle 128b/132b SST in intel_ddi_read_func_ctl()")
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250224093242.1859583-1-imre.deak@intel.com
(cherry picked from commit 0159e311772af9d6598aafe072c020687720f1d7)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The async call to __guc_exec_queue_fini_async frees the scheduler
while a submission may time out and restart. To prevent this race
condition, the pending job timer should be canceled before freeing
the scheduler.
V3(MattB):
- Adjust position of cancel pending job
- Remove gitlab issue# from commit message
V2(MattB):
- Cancel pending jobs before scheduler finish
Fixes: a20c75dba192 ("drm/xe: Call __guc_exec_queue_fini_async direct for KERNEL exec_queues")
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250225045754.600905-1-tejas.upadhyay@intel.com
Signed-off-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
(cherry picked from commit 18fbd567e75f9b97b699b2ab4f1fa76b7cf268f6)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Commit b79e8fd954c4 ("drm/xe: Remove dependency on intel_engine_regs.h")
introduced an internal set of engine registers, however, as part of this
change, it has also introduced two duplicate `define' lines for
`RING_CTL_SIZE(size)'. This commit was introduced to the tree in v6.8-rc1.
While this is harmless as the definitions did not change, so no compiler
warning was observed.
Drop this line anyway for the sake of correctness.
Cc: stable@vger.kernel.org # v6.8-rc1+
Fixes: b79e8fd954c4 ("drm/xe: Remove dependency on intel_engine_regs.h")
Signed-off-by: Mingcong Bai <jeffbai@aosc.io>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250225073104.865230-1-jeffbai@aosc.io
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 6b68c4542ffecc36087a9e14db8fc990c88bb01b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Commit 8c87215dd3a2 ("ata: libahci_platform: support non-consecutive port
numbers") added a skip to ahci_platform_enable_phys() for ports that are
not in mask_port_map.
The code in ahci_platform_get_resources(), will currently set mask_port_map
for each child "port" node it finds in the device tree.
However, device trees that do not have any child "port" nodes will not have
mask_port_map set, and for non-device tree platforms mask_port_map will
only exist as a quirk for specific PCI device + vendor IDs, or as a kernel
module parameter, but will not be set by default.
Therefore, the common thing is that mask_port_map is only set if you do not
want to use all ports (as defined by Offset 0Ch: PI – Ports Implemented
register), but instead only want to use the ports in mask_port_map. If
mask_port_map is not set, all ports are available.
Thus, ahci_ignore_port() must be able to handle an empty mask_port_map.
Fixes: 8c87215dd3a2 ("ata: libahci_platform: support non-consecutive port numbers")
Fixes: 2c202e6c4f4d ("ata: libahci_platform: Do not set mask_port_map when not needed")
Fixes: c9b5be909e65 ("ahci: Introduce ahci_ignore_port() helper")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/linux-ide/10b31dd0-d0bb-4f76-9305-2195c3e17670@samsung.com/
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Co-developed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250225141612.942170-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
drivers/gpu/drm/imagination/ includes local headers with the double-quote
form (#include "...").
Hence, the header search path addition is unneeded.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Matt Coster <matt.coster@imgtec.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250210102352.1517115-1-masahiroy@kernel.org
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
|
|
There is an off-by-one issue for the err_chained_bd path, it will free
one more tx_swbd than expected. But there is no such issue for the
err_map_data path. To fix this off-by-one issue and make the two error
handling consistent, the increment of 'i' and 'count' remain in sync
and enetc_unwind_tx_frame() is called for error handling.
Fixes: fb8629e2cbfc ("net: enetc: add support for software TSO")
Cc: stable@vger.kernel.org
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-9-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the ENETC v4 driver has not added the MAC merge layer support
in the upstream, so the mm_lock is not initialized and used, so remove
the mm_lock from the driver.
Fixes: 99100d0d9922 ("net: enetc: add preliminary support for i.MX95 ENETC PF")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-8-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The enetc4_link_init() is called when the PF driver probes to create
phylink and MDIO bus, but we forgot to call enetc4_link_deinit() to
free the phylink and MDIO bus when the driver was unbound. so add
missing enetc4_link_deinit() to enetc4_pf_netdev_destroy().
Fixes: 99100d0d9922 ("net: enetc: add preliminary support for i.MX95 ENETC PF")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-7-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is an issue with one-step timestamp based on UDP/IP. The peer will
discard the sync packet because of the wrong UDP checksum. For ENETC v1,
the software needs to update the UDP checksum when updating the
originTimestamp field, so that the hardware can correctly update the UDP
checksum when updating the correction field. Otherwise, the UDP checksum
in the sync packet will be wrong.
Fixes: 7294380c5211 ("enetc: support PTP Sync packet one-step timestamping")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-6-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Actually ENETC VFs do not support HWTSTAMP_TX_ONESTEP_SYNC because only
ENETC PF can access PMa_SINGLE_STEP registers. And there will be a crash
if VFs are used to test one-step timestamp, the crash log as follows.
[ 129.110909] Unable to handle kernel paging request at virtual address 00000000000080c0
[ 129.287769] Call trace:
[ 129.290219] enetc_port_mac_wr+0x30/0xec (P)
[ 129.294504] enetc_start_xmit+0xda4/0xe74
[ 129.298525] enetc_xmit+0x70/0xec
[ 129.301848] dev_hard_start_xmit+0x98/0x118
Fixes: 41514737ecaa ("enetc: add get_ts_info interface for ethtool")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-5-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 'xdp_tx' is used to count the number of XDP_TX frames sent, not the
number of Tx BDs.
Fixes: 7ed2bc80074e ("net: enetc: add support for XDP_TX")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-4-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When creating a TSO header, if the skb is VLAN tagged, the extended BD
will be used and the 'count' should be increased by 2 instead of 1.
Otherwise, when an error occurs, less tx_swbd will be freed than the
actual number.
Fixes: fb8629e2cbfc ("net: enetc: add support for software TSO")
Cc: stable@vger.kernel.org
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-3-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a DMA mapping error occurs while processing skb frags, it will free
one more tx_swbd than expected, so fix this off-by-one issue.
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Cc: stable@vger.kernel.org
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-2-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The commit 23c0e5a16bcc ("ixgbe: Add link management support for E610
device") introduced incorrect checking of media cage presence for E610
device. Fix it.
Fixes: 23c0e5a16bcc ("ixgbe: Add link management support for E610 device")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/e7d73b32-f12a-49d1-8b60-1ef83359ec13@stanley.mountain/
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-6-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have recently seen reports of lockdep circular lock dependency warnings
when loading the iAVF driver:
[ 1504.790308] ======================================================
[ 1504.790309] WARNING: possible circular locking dependency detected
[ 1504.790310] 6.13.0 #net_next_rt.c2933b2befe2.el9 Not tainted
[ 1504.790311] ------------------------------------------------------
[ 1504.790312] kworker/u128:0/13566 is trying to acquire lock:
[ 1504.790313] ffff97d0e4738f18 (&dev->lock){+.+.}-{4:4}, at: register_netdevice+0x52c/0x710
[ 1504.790320]
[ 1504.790320] but task is already holding lock:
[ 1504.790321] ffff97d0e47392e8 (&adapter->crit_lock){+.+.}-{4:4}, at: iavf_finish_config+0x37/0x240 [iavf]
[ 1504.790330]
[ 1504.790330] which lock already depends on the new lock.
[ 1504.790330]
[ 1504.790330]
[ 1504.790330] the existing dependency chain (in reverse order) is:
[ 1504.790331]
[ 1504.790331] -> #1 (&adapter->crit_lock){+.+.}-{4:4}:
[ 1504.790333] __lock_acquire+0x52d/0xbb0
[ 1504.790337] lock_acquire+0xd9/0x330
[ 1504.790338] mutex_lock_nested+0x4b/0xb0
[ 1504.790341] iavf_finish_config+0x37/0x240 [iavf]
[ 1504.790347] process_one_work+0x248/0x6d0
[ 1504.790350] worker_thread+0x18d/0x330
[ 1504.790352] kthread+0x10e/0x250
[ 1504.790354] ret_from_fork+0x30/0x50
[ 1504.790357] ret_from_fork_asm+0x1a/0x30
[ 1504.790361]
[ 1504.790361] -> #0 (&dev->lock){+.+.}-{4:4}:
[ 1504.790364] check_prev_add+0xf1/0xce0
[ 1504.790366] validate_chain+0x46a/0x570
[ 1504.790368] __lock_acquire+0x52d/0xbb0
[ 1504.790370] lock_acquire+0xd9/0x330
[ 1504.790371] mutex_lock_nested+0x4b/0xb0
[ 1504.790372] register_netdevice+0x52c/0x710
[ 1504.790374] iavf_finish_config+0xfa/0x240 [iavf]
[ 1504.790379] process_one_work+0x248/0x6d0
[ 1504.790381] worker_thread+0x18d/0x330
[ 1504.790383] kthread+0x10e/0x250
[ 1504.790385] ret_from_fork+0x30/0x50
[ 1504.790387] ret_from_fork_asm+0x1a/0x30
[ 1504.790389]
[ 1504.790389] other info that might help us debug this:
[ 1504.790389]
[ 1504.790389] Possible unsafe locking scenario:
[ 1504.790389]
[ 1504.790390] CPU0 CPU1
[ 1504.790391] ---- ----
[ 1504.790391] lock(&adapter->crit_lock);
[ 1504.790393] lock(&dev->lock);
[ 1504.790394] lock(&adapter->crit_lock);
[ 1504.790395] lock(&dev->lock);
[ 1504.790397]
[ 1504.790397] *** DEADLOCK ***
This appears to be caused by the change in commit 5fda3f35349b ("net: make
netdev_lock() protect netdev->reg_state"), which added a netdev_lock() in
register_netdevice.
The iAVF driver calls register_netdevice() from iavf_finish_config(), as a
final stage of its state machine post-probe. It currently takes the RTNL
lock, then the netdev lock, and then the device critical lock. This pattern
is used throughout the driver. Thus there is a strong dependency that the
crit_lock should not be acquired before the net device lock. The change to
register_netdevice creates an ABBA lock order violation because the iAVF
driver is holding the crit_lock while calling register_netdevice, which
then takes the netdev_lock.
It seems likely that future refactors could result in netdev APIs which
hold the netdev_lock while calling into the driver. This means that we
should not re-order the locks so that netdev_lock is acquired after the
device private crit_lock.
Instead, notice that we already release the netdev_lock prior to calling
the register_netdevice. This flow only happens during the early driver
initialization as we transition through the __IAVF_STARTUP,
__IAVF_INIT_VERSION_CHECK, __IAVF_INIT_GET_RESOURCES, etc.
Analyzing the places where we take crit_lock in the driver there are two
sources:
a) several of the work queue tasks including adminq_task, watchdog_task,
reset_task, and the finish_config task.
b) various callbacks which ultimately stem back to .ndo operations or
ethtool operations.
The latter cannot be triggered until after the netdevice registration is
completed successfully.
The iAVF driver uses alloc_ordered_workqueue, which is an unbound workqueue
that has a max limit of 1, and thus guarantees that only a single work item
on the queue is executing at any given time, so none of the other work
threads could be executing due to the ordered workqueue guarantees.
The iavf_finish_config() function also does not do anything else after
register_netdevice, unless it fails. It seems unlikely that the driver
private crit_lock is protecting anything that register_netdevice() itself
touches.
Thus, to fix this ABBA lock violation, lets simply release the
adapter->crit_lock as well as netdev_lock prior to calling
register_netdevice(). We do still keep holding the RTNL lock as required by
the function. If we do fail to register the netdevice, then we re-acquire
the adapter critical lock to finish the transition back to
__IAVF_INIT_CONFIG_ADAPTER.
This ensures every call where both netdev_lock and the adapter->crit_lock
are acquired under the same ordering.
Fixes: afc664987ab3 ("eth: iavf: extend the netdev_lock usage")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As part of switchdev environment setup, uplink VSI is configured as
default for both Tx and Rx. Default Rx VSI is also used by promiscuous
mode. If promisc mode is enabled and an attempt to enter switchdev mode
is made, the setup will fail because Rx VSI is already configured as
default (rule exists).
Reproducer:
devlink dev eswitch set $PF1_PCI mode switchdev
ip l s $PF1 up
ip l s $PF1 promisc on
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
In switchdev setup, use ice_set_dflt_vsi() instead of plain
ice_cfg_dflt_vsi(), which avoids repeating setting default VSI for Rx if
it's already configured.
Fixes: 50d62022f455 ("ice: default Tx rule instead of to queue")
Reported-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Closes: https://lore.kernel.org/intel-wired-lan/PH0PR11MB50138B635F2E5CEB7075325D961F2@PH0PR11MB5013.namprd11.prod.outlook.com
Reviewed-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If ice_ena_vfs() fails after calling ice_create_vf_entries(), it frees
all VFs without removing them from snapshot PF-VF mailbox list, leading
to list corruption.
Reproducer:
devlink dev eswitch set $PF1_PCI mode switchdev
ip l s $PF1 up
ip l s $PF1 promisc on
sleep 1
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
Trace (minimized):
list_add corruption. next->prev should be prev (ffff8882e241c6f0), but was 0000000000000000. (next=ffff888455da1330).
kernel BUG at lib/list_debug.c:29!
RIP: 0010:__list_add_valid_or_report+0xa6/0x100
ice_mbx_init_vf_info+0xa7/0x180 [ice]
ice_initialize_vf_entry+0x1fa/0x250 [ice]
ice_sriov_configure+0x8d7/0x1520 [ice]
? __percpu_ref_switch_mode+0x1b1/0x5d0
? __pfx_ice_sriov_configure+0x10/0x10 [ice]
Sometimes a KASAN report can be seen instead with a similar stack trace:
BUG: KASAN: use-after-free in __list_add_valid_or_report+0xf1/0x100
VFs are added to this list in ice_mbx_init_vf_info(), but only removed
in ice_free_vfs(). Move the removing to ice_free_vf_entries(), which is
also being called in other places where VFs are being removed (including
ice_free_vfs() itself).
Fixes: 8cd8a6b17d27 ("ice: move VF overflow message count into struct ice_mbx_vf_info")
Reported-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Closes: https://lore.kernel.org/intel-wired-lan/PH0PR11MB50138B635F2E5CEB7075325D961F2@PH0PR11MB5013.namprd11.prod.outlook.com
Reviewed-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
am65-cpsw uses page_pool_dev_alloc_pages(), thus needs PAGE_POOL
selected to avoid linker errors. This is missing since the driver
started to use page_pool helpers in 8acacc40f733 ("net: ethernet:
ti: am65-cpsw: Add minimal XDP support")
Fixes: 8acacc40f733 ("net: ethernet: ti: am65-cpsw: Add minimal XDP support")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20250224-net-am654-nuss-kconfig-v2-1-c124f4915c92@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull rdma fixes from Jason Gunthorpe:
- Fix a mlx5 malfunction if the UMR QP gets an error
- Return the correct port number to userspace for a mlx5 DCT
- Don't cause a UMR QP error if DMABUF teardown races with invalidation
- Fix a WARN splat when unregisering so mlx5 device memory MR types
- Use the correct alignment for the mana doorbell so that two processes
do not share the same physical page on non-4k page systems
- MAINTAINERS updates for MANA
- Retry failed HNS FW commands because some can take a long time
- Cast void * handle to the correct type in bnxt to fix corruption
- Avoid a NULL pointer crash in bnxt_re
- Fix skipped ib_device_unregsiter() for bnxt_re due to some earlier
rework
- Correctly detect if the bnxt supports extended statistics
- Fix refcount leak in mlx5 odp introduced by a previous fix
- Map the FW result for the port rate to the userspace values properly
in mlx5, returns correct values for newer 800G ports
- Don't wrongly destroy counters objects that were not automatically
created during mlx5 bind qp
- Set page size/shift members of kernel owned SRQs to fix a crash in
nvme target
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/bnxt_re: Fix the page details for the srq created by kernel consumers
RDMA/mlx5: Fix bind QP error cleanup flow
RDMA/mlx5: Fix AH static rate parsing
RDMA/mlx5: Fix implicit ODP hang on parent deregistration
RDMA/bnxt_re: Fix the statistics for Gen P7 VF
RDMA/bnxt_re: Fix issue in the unload path
RDMA/bnxt_re: Add sanity checks on rdev validity
RDMA/bnxt_re: Fix an issue in bnxt_re_async_notifier
RDMA/hns: Fix mbox timing out by adding retry mechanism
MAINTAINERS: update maintainer for Microsoft MANA RDMA driver
RDMA/mana_ib: Allocate PAGE aligned doorbell index
RDMA/mlx5: Fix a WARN during dereg_mr for DM type
RDMA/mlx5: Fix a race for DMABUF MR which can lead to CQE with error
IB/mlx5: Set and get correct qp_num for a DCT QP
RDMA/mlx5: Fix the recovery flow of the UMR QP
|
|
Otherwise an uninitialized value can be returned if
amdgpu_res_cleared returns true for all regions.
Possibly closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3812
Fixes: a68c7eaa7a8f ("drm/amdgpu: Enable clear page functionality")
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7c62aacc3b452f73a1284198c81551035fac6d71)
Cc: stable@vger.kernel.org
|
|
[Why]
DC is not using amdgpu_irq_get/put to manage the HPD interrupt refcounts.
So when amdgpu_irq_gpu_reset_resume_helper() reprograms all of the IRQs,
HPD gets disabled.
[How]
Use amdgpu_irq_get/put() for HPD init/fini in DM in order to sync refcounts
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f3dde2ff7fcaacd77884502e8f572f2328e9c745)
Cc: stable@vger.kernel.org
|
|
[why]
some board designs have eDP0 connected to DP1, need a way to enable
support_edp0_on_dp1 flag, otherwise edp related features cannot work
[how]
do a dmi check during dm initialization to identify systems that
require support_edp0_on_dp1. Optimize quirk table with callback
functions to set quirk entries, retrieve_dmi_info can set quirks
according to quirk entries
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Yilin Chen <Yilin.Chen@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f6d17270d18a6a6753fff046330483d43f8405e4)
Cc: stable@vger.kernel.org
|
|
[Why]
PSR-SU may cause some glitching randomly on several panels.
[How]
Temporarily disable the PSR-SU and fallback to PSR1 for
all eDP panels.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3388
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 6deeefb820d0efb0b36753622fb982d03b37b3ad)
Cc: stable@vger.kernel.org
|
|
When switching to drm_edid, we slightly changed how to get edid by
removing the possibility of getting them from dc_link when in aux
transaction mode. As MST doesn't initialize the connector with
`drm_connector_init_with_ddc()`, restore the original behavior to avoid
functional changes.
v2:
- Fix build warning of unchecked dereference (kernel test bot)
CC: Alex Hung <alex.hung@amd.com>
CC: Mario Limonciello <mario.limonciello@amd.com>
CC: Roman Li <Roman.Li@amd.com>
CC: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Fixes: 48edb2a4256e ("drm/amd/display: switch amdgpu_dm_connector to use struct drm_edid")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 81262b1656feb3813e3d917ab78824df6831e69e)
|
|
Re-send the mes message on resume to make sure the
mes state is up to date.
Fixes: 8521e3c5f058 ("drm/amd/amdgpu: limit single process inside MES")
Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Shaoyun Liu <shaoyun.liu@amd.com>
Cc: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 27b791514789844e80da990c456c2465325e0851)
|
|
This should not be called on chips without MES so check if
MES is enabled and if the cleaner shader is supported.
Fixes: 8521e3c5f058 ("drm/amd/amdgpu: limit single process inside MES")
Reviewed-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Shaoyun Liu <shaoyun.liu@amd.com>
Cc: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
(cherry picked from commit 80513e389765c8f9543b26d8fa4bbdf0e59ff8bc)
|
|
There was a quirk added to add a workaround for a Sapphire
RX 5600 XT Pulse that didn't allow BAR resizing. However,
the quirk caused a regression with runtime pm on Dell laptops
using those chips, rather than narrowing the scope of the
resizing quirk, add a quirk to prevent amdgpu from resizing
the BAR on those Dell platforms unless runtime pm is disabled.
v2: update commit message, add runpm check
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/1707
Fixes: 907830b0fc9e ("PCI: Add a REBAR size quirk for Sapphire RX 5600 XT Pulse")
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 5235053f443cef4210606e5fb71f99b915a9723d)
Cc: stable@vger.kernel.org
|
|
When userspace applications call AMDKFD_IOC_UPDATE_QUEUE. Preserve
bitfields that do not need to be modified as they contain flags to
track queue states that are used by CP FW.
Signed-off-by: David Yat Sin <David.YatSin@amd.com>
Reviewed-by: Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8150827990b709ab5a40c46c30d21b7f7b9e9440)
Cc: stable@vger.kernel.org
|
|
resume and irq handler happily races in set_power_state()
* amdgpu_legacy_dpm_compute_clocks() needs lock
* protect irq work handler
* fix dpm_enabled usage
v2: fix clang build, integrate Lijo's comments (Alex)
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2524
Fixes: 3712e7a49459 ("drm/amd/pm: unified lock protections in amdgpu_dpm.c")
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> # on Oland PRO
Signed-off-by: chr[] <chris@rudorff.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit ee3dc9e204d271c9c7a8d4d38a0bce4745d33e71)
Cc: stable@vger.kernel.org
|
|
All the callers assume nvme_map_user_request() frees the request on a
failure. This wasn't happening on invalid metadata or io_uring command
flags, so we've been leaking those requests.
Fixes: 23fd22e55b767b ("nvme: wire up fixed buffer support for nvme passthrough")
Fixes: 7c2fd76048e95d ("nvme: fix metadata handling in nvme-passthrough")
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Pinctrl is an essential driver for SpacemiT's SoC,
The uart driver requires it, same as sd card driver,
so let's enable it by default for this SoC.
The CONFIG_PINCTRL_SPACEMIT_K1 isn't enabled when using
'make defconfig' to select kernel configuration options.
This result in a broken uart driver where fail at probe()
stage due to no pins found.
Fixes: a83c29e1d145 ("pinctrl: spacemit: add support for SpacemiT K1 SoC")
Reported-by: Alex Elder <elder@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Alex Elder <elder@riscstar.com>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/20250218-k1-pinctrl-option-v3-1-36e031e0da1b@gentoo.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
devm_kasprintf() calls can return null pointers on failure.
But the return values were not checked in npcm8xx_gpio_fw().
Add NULL check in npcm8xx_gpio_fw(), to handle kernel NULL
pointer dereference error.
Fixes: acf4884a5717 ("pinctrl: nuvoton: add NPCM8XX pinctrl and GPIO driver")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://lore.kernel.org/20250212100532.4317-1-hanchunchao@inspur.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The max_registers value does not take into consideration the stride;
currently, it's set to the number of the last pin, but this does not
accurately represent the final register.
Fix this by multiplying the current value by 4.
Fixes: 54b1aa5a5b16 ("ARM: pinctrl: Add Broadcom Capri pinctrl driver")
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/20250207-bcm21664-pinctrl-v1-2-e7cfac9b2d3b@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
fixp2int always rounds down, fixp2int_ceil rounds up. We need
the new fixp2int_round.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241220043410.416867-3-alex.hung@amd.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
Change calls to async regmap write functions to use the normal
blocking writes so that the cs35l56 driver can use spi_bus_lock() to
gain exclusive access to the SPI bus.
As this is part of a fix, it makes only the minimal change to swap the
functions to the blocking equivalents. There's no need to risk
reworking the buffer allocation logic that is now partially redundant.
The async writes are a 12-year-old workaround for inefficiency of
synchronous writes in the SPI subsystem. The SPI subsystem has since
been changed to avoid the overheads, so this workaround should not be
necessary.
The cs35l56 driver needs to use spi_bus_lock() prevent bus activity
while it is soft-resetting the cs35l56. But spi_bus_lock() is
incompatible with spi_async() calls, which will fail with -EBUSY.
Fixes: 8a731fd37f8b ("ASoC: cs35l56: Move utility functions to shared file")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250225131843.113752-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
OA exponent value of 0 is a valid value for periodic reports. Allow user
to pass 0 for the OA sampling interval since it gets converted to 2 gt
clock ticks.
v2: Update the check in xe_oa_stream_init as well (Ashutosh)
v3: Fix mi-rpc failure by setting default exponent to -1 (CI)
v4: Add the Fixes tag
Fixes: b6fd51c62119 ("drm/xe/oa/uapi: Define and parse OA stream properties")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250221213352.1712932-1-umesh.nerlige.ramappa@intel.com
(cherry picked from commit 30341f0b8ea71725cc4ab2c43e3a3b749892fc92)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
params->total_weight is not initialized during bind and not updated when
the bound cdev changes. The cooling device weight will not be used due
to the uninitialized total_weight, until an update via sysfs is
triggered.
The bound cdevs are updated during thermal zone registration, where each
cooling device will be bound to the thermal zone one by one, but
power_allocator_bind() can be called without an additional cdev update
when manually changing the policy of a thermal zone via sysfs.
Add a new function to handle weight update logic, including updating
total_weight, and call it when bind, weight changes, and cdev updates to
ensure total_weight is always correct.
Fixes: a3cd6db4cc2e ("thermal: gov_power_allocator: Support new update callback of weights")
Signed-off-by: Yu-Che Cheng <giver@chromium.org>
Link: https://patch.msgid.link/20250222-fix-power-allocator-weight-v2-1-a94de86b685a@chromium.org
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since thermal_of_should_bind() terminates the loop after processing
the first child found in cooling-maps, it will never match more than
one cdev to a given trip point which is incorrect, as there may be
cooling-maps associating one trip point with multiple cooling devices.
Address this by letting the loop continue until either all
children have been processed or a matching one has been found.
To avoid adding conditionals or goto statements, put the loop in
question into a separate function and make that function return
right away after finding a matching cooling-maps entry.
Fixes: 94c6110b0b13 ("thermal/of: Use the .should_bind() thermal zone callback")
Link: https://lore.kernel.org/linux-pm/20250219-fix-thermal-of-v1-1-de36e7a590c4@chromium.org/
Reported-by: Yu-Che Cheng <giver@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Yu-Che Cheng <giver@chromium.org>
Tested-by: Yu-Che Cheng <giver@chromium.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/2788228.mvXUDI8C0e@rjwysocki.net
|
|
When an Icelake or Sapphire Rapids CPU isn't providing the maximum and
critical thresholds for particular DIMM the driver should return an
error to the userspace instead of giving it stale (best case) or wrong
(the structure contains all zeros after kzalloc() call) data.
The issue can be reproduced by binding the peci driver while the host is
fully booted and idle, this makes PECI interaction unreliable enough.
Fixes: 73bc1b885dae ("hwmon: peci: Add dimmtemp driver")
Fixes: 621995b6d795 ("hwmon: (peci/dimmtemp) Add Sapphire Rapids support")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20250123122003.6010-1-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mikulas Patocka:
- dm-vdo: add missing spin_lock_init
- dm-integrity: divide-by-zero fix
- dm-integrity: do not report unused entries in the table line
* tag 'for-6.14/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm vdo: add missing spin_lock_init
dm-integrity: Do not emit journal configuration in DM table for Inline mode
dm-integrity: Avoid divide by zero in table status in Inline mode
|
|
The PCI P2PDMA code will register the CMB block to the memory
hot-plugging subsystem, which have an alignment requirement. Memory
blocks that do not satisfy this alignment requirement (usually 2MB) will
lead to a WARNING from memory hotplugging.
Verify the CMB block's address and size against the alignment and only
try to send CMB blocks compatible with it to prevent this warning.
Tested on Intel DC D4502 SSD, which has a 512K CMB block that is too
small for memory hotplugging (thus PCI P2PDMA).
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
CMB decoding should get disabled when the CMB block isn't successfully
registered to P2P DMA subsystem.
Clean up the CMBMSC register in this error handling codepath to disable
CMB decoding (and CMBLOC/CMBSZ registers).
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
nvme_tcp_poll() may race with the send path error handler because
it may complete the request while it is actively being polled for
completion, resulting in a UAF panic [1]:
We should make sure to stop polling when we see an error when
trying to read from the socket. Hence make sure to propagate the
error so that the block layer breaks the polling cycle.
[1]:
--
[35665.692310] nvme nvme2: failed to send request -13
[35665.702265] nvme nvme2: unsupported pdu type (3)
[35665.702272] BUG: kernel NULL pointer dereference, address: 0000000000000000
[35665.702542] nvme nvme2: queue 1 receive failed: -22
[35665.703209] #PF: supervisor write access in kernel mode
[35665.703213] #PF: error_code(0x0002) - not-present page
[35665.703214] PGD 8000003801cce067 P4D 8000003801cce067 PUD 37e6f79067 PMD 0
[35665.703220] Oops: 0002 [#1] SMP PTI
[35665.703658] nvme nvme2: starting error recovery
[35665.705809] Hardware name: Inspur aaabbb/YZMB-00882-104, BIOS 4.1.26 09/22/2022
[35665.705812] Workqueue: kblockd blk_mq_requeue_work
[35665.709172] RIP: 0010:_raw_spin_lock+0xc/0x30
[35665.715788] Call Trace:
[35665.716201] <TASK>
[35665.716613] ? show_trace_log_lvl+0x1c1/0x2d9
[35665.717049] ? show_trace_log_lvl+0x1c1/0x2d9
[35665.717457] ? blk_mq_request_bypass_insert+0x2c/0xb0
[35665.717950] ? __die_body.cold+0x8/0xd
[35665.718361] ? page_fault_oops+0xac/0x140
[35665.718749] ? blk_mq_start_request+0x30/0xf0
[35665.719144] ? nvme_tcp_queue_rq+0xc7/0x170 [nvme_tcp]
[35665.719547] ? exc_page_fault+0x62/0x130
[35665.719938] ? asm_exc_page_fault+0x22/0x30
[35665.720333] ? _raw_spin_lock+0xc/0x30
[35665.720723] blk_mq_request_bypass_insert+0x2c/0xb0
[35665.721101] blk_mq_requeue_work+0xa5/0x180
[35665.721451] process_one_work+0x1e8/0x390
[35665.721809] worker_thread+0x53/0x3d0
[35665.722159] ? process_one_work+0x390/0x390
[35665.722501] kthread+0x124/0x150
[35665.722849] ? set_kthread_struct+0x50/0x50
[35665.723182] ret_from_fork+0x1f/0x30
Reported-by: Zhang Guanghui <zhang.guanghui@cestc.cn>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Test XDP and HDS interaction. While at it add a test for using the IOCTL,
as that turned out to be the real culprit.
Testing bnxt:
# NETIF=eth0 ./ksft-net-drv/drivers/net/hds.py
KTAP version 1
1..12
ok 1 hds.get_hds
ok 2 hds.get_hds_thresh
ok 3 hds.set_hds_disable # SKIP disabling of HDS not supported by the device
ok 4 hds.set_hds_enable
ok 5 hds.set_hds_thresh_zero
ok 6 hds.set_hds_thresh_max
ok 7 hds.set_hds_thresh_gt
ok 8 hds.set_xdp
ok 9 hds.enabled_set_xdp
ok 10 hds.ioctl
ok 11 hds.ioctl_set_xdp
ok 12 hds.ioctl_enabled_set_xdp
# Totals: pass:11 fail:0 xfail:0 xpass:0 skip:1 error:0
and netdevsim:
# ./ksft-net-drv/drivers/net/hds.py
KTAP version 1
1..12
ok 1 hds.get_hds
ok 2 hds.get_hds_thresh
ok 3 hds.set_hds_disable
ok 4 hds.set_hds_enable
ok 5 hds.set_hds_thresh_zero
ok 6 hds.set_hds_thresh_max
ok 7 hds.set_hds_thresh_gt
ok 8 hds.set_xdp
ok 9 hds.enabled_set_xdp
ok 10 hds.ioctl
ok 11 hds.ioctl_set_xdp
ok 12 hds.ioctl_enabled_set_xdp
# Totals: pass:12 fail:0 xfail:0 xpass:0 skip:0 error:0
Netdevsim needs a sane default for tx/rx ring size.
ethtool 6.11 is needed for the --disable-netlink option.
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Tested-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250221025141.1132944-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently we treat EFAULT from hmm_range_fault() as a non-fatal error
when called from xe_vm_userptr_pin() with the idea that we want to avoid
killing the entire vm and chucking an error, under the assumption that
the user just did an unmap or something, and has no intention of
actually touching that memory from the GPU. At this point we have
already zapped the PTEs so any access should generate a page fault, and
if the pin fails there also it will then become fatal.
However it looks like it's possible for the userptr vma to still be on
the rebind list in preempt_rebind_work_func(), if we had to retry the
pin again due to something happening in the caller before we did the
rebind step, but in the meantime needing to re-validate the userptr and
this time hitting the EFAULT.
This explains an internal user report of hitting:
[ 191.738349] WARNING: CPU: 1 PID: 157 at drivers/gpu/drm/xe/xe_res_cursor.h:158 xe_pt_stage_bind.constprop.0+0x60a/0x6b0 [xe]
[ 191.738551] Workqueue: xe-ordered-wq preempt_rebind_work_func [xe]
[ 191.738616] RIP: 0010:xe_pt_stage_bind.constprop.0+0x60a/0x6b0 [xe]
[ 191.738690] Call Trace:
[ 191.738692] <TASK>
[ 191.738694] ? show_regs+0x69/0x80
[ 191.738698] ? __warn+0x93/0x1a0
[ 191.738703] ? xe_pt_stage_bind.constprop.0+0x60a/0x6b0 [xe]
[ 191.738759] ? report_bug+0x18f/0x1a0
[ 191.738764] ? handle_bug+0x63/0xa0
[ 191.738767] ? exc_invalid_op+0x19/0x70
[ 191.738770] ? asm_exc_invalid_op+0x1b/0x20
[ 191.738777] ? xe_pt_stage_bind.constprop.0+0x60a/0x6b0 [xe]
[ 191.738834] ? ret_from_fork_asm+0x1a/0x30
[ 191.738849] bind_op_prepare+0x105/0x7b0 [xe]
[ 191.738906] ? dma_resv_reserve_fences+0x301/0x380
[ 191.738912] xe_pt_update_ops_prepare+0x28c/0x4b0 [xe]
[ 191.738966] ? kmemleak_alloc+0x4b/0x80
[ 191.738973] ops_execute+0x188/0x9d0 [xe]
[ 191.739036] xe_vm_rebind+0x4ce/0x5a0 [xe]
[ 191.739098] ? trace_hardirqs_on+0x4d/0x60
[ 191.739112] preempt_rebind_work_func+0x76f/0xd00 [xe]
Followed by NPD, when running some workload, since the sg was never
actually populated but the vma is still marked for rebind when it should
be skipped for this special EFAULT case. This is confirmed to fix the
user report.
v2 (MattB):
- Move earlier.
v3 (MattB):
- Update the commit message to make it clear that this indeed fixes the
issue.
Fixes: 521db22a1d70 ("drm/xe: Invalidate userptr VMA on page pin fault")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: <stable@vger.kernel.org> # v6.10+
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250221143840.167150-5-matthew.auld@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 6b93cb98910c826c2e2004942f8b060311e43618)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
On error restore anything still on the pin_list back to the invalidation
list on error. For the actual pin, so long as the vma is tracked on
either list it should get picked up on the next pin, however it looks
possible for the vma to get nuked but still be present on this per vm
pin_list leading to corruption. An alternative might be then to instead
just remove the link when destroying the vma.
v2:
- Also add some asserts.
- Keep the overzealous locking so that we are consistent with the docs;
updating the docs and related bits will be done as a follow up.
Fixes: ed2bdf3b264d ("drm/xe/vm: Subclass userptr vmas")
Suggested-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: <stable@vger.kernel.org> # v6.8+
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250221143840.167150-4-matthew.auld@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 4e37e928928b730de9aa9a2f5dc853feeebc1742)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Signed-off-by: Ken Raeburn <raeburn@redhat.com>
Signed-off-by: Matthew Sakai <msakai@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
|
