summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2025-07-24rtc: Optimize calculations in rtc_time64_to_tm()Uwe Kleine-König1-21/+19
Recently (in commit 7df4cfef8b35 ("rtc: Make rtc_time64_to_tm() support dates before 1970")) the function rtc_time64_to_tm() was repaired for times before 1970. This introduced two if blocks. Cassio Neri pointed out that to be not neccessary and suggested an adaption that allows to drop the two branch points again. This is implemented here. Also adapt the reference to the theoretical paper to link to the final published article instead of the preprint on Cassio's request. Suggested-by: Cassio Neri <cassio.neri@gmail.com> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Link: https://lore.kernel.org/r/20250613142405.253420-2-u.kleine-koenig@baylibre.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2025-07-24rtc: ds1307: handle oscillator stop flag (OSF) for ds1341Meagan Lloyd1-0/+11
In using CONFIG_RTC_HCTOSYS, rtc_hctosys() will sync the RTC time to the kernel time as long as rtc_read_time() succeeds. In some power loss situations, our supercapacitor-backed DS1342 RTC comes up with either an unpredictable future time or the default 01/01/00 from the datasheet. The oscillator stop flag (OSF) is set in these scenarios due to the power loss and can be used to determine the validity of the RTC data. This change expands the oscillator stop flag (OSF) handling that has already been implemented for some chips to the ds1341 chip (DS1341 and DS1342 share a datasheet). This handling manages the validity of the RTC data in .read_time and .set_time based on the OSF. Signed-off-by: Meagan Lloyd <meaganlloyd@linux.microsoft.com> Reviewed-by: Tyler Hicks <code@tyhicks.com> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Link: https://lore.kernel.org/r/1749665656-30108-3-git-send-email-meaganlloyd@linux.microsoft.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2025-07-24rtc: ds1307: remove clear of oscillator stop flag (OSF) in probeMeagan Lloyd1-3/+1
In using CONFIG_RTC_HCTOSYS, rtc_hctosys() will sync the RTC time to the kernel time as long as rtc_read_time() succeeds. In some power loss situations, our supercapacitor-backed DS1342 RTC comes up with either an unpredictable future time or the default 01/01/00 from the datasheet. The oscillator stop flag (OSF) is set in these scenarios due to the power loss and can be used to determine the validity of the RTC data. Some chip types in the ds1307 driver already have OSF handling to determine whether .read_time provides valid RTC data or returns -EINVAL. This change removes the clear of the OSF in .probe as the OSF needs to be preserved to expand the OSF handling to the ds1341 chip type (note that DS1341 and DS1342 share a datasheet). Signed-off-by: Meagan Lloyd <meaganlloyd@linux.microsoft.com> Reviewed-by: Tyler Hicks <code@tyhicks.com> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Link: https://lore.kernel.org/r/1749665656-30108-2-git-send-email-meaganlloyd@linux.microsoft.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2025-07-23Merge tag 'drm-misc-fixes-2025-07-23' of ↵Dave Airlie15-38/+99
https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes drm-misc-fixes for v6.16-rc8/final?: - Revert all uses of drm_gem_object->dmabuf to drm_gem_object->import_attach->dmabuf. - Fix amdgpu returning BIOS cluttered VRAM after resume. - Scheduler hang fix. - Revert nouveau ioctl fix as it caused regressions. - Fix null pointer deref in nouveau. - Fix unnecessary semicolon in ti_sn_bridge_probe. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://lore.kernel.org/r/72235afd-c849-49fe-9cc1-2b1781abdf08@linux.intel.com
2025-07-23binder: Remove unused binder lock eventsSteven Rostedt1-21/+0
Trace events can take up to 5K each when they are defined, regardless if they are used or not. The binder lock events: binder_lock, binder_locked and binder_unlock are no longer used. Remove them. Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Arve =?utf-8?b?SGrDuG5u?= =?utf-8?b?ZXbDpWc=?= " <arve@android.com> Cc: Todd Kjos <tkjos@android.com> Cc: Martijn Coenen <maco@android.com> Cc: Joel Fernandes <joelagnelf@nvidia.com> Cc: Christian Brauner <brauner@kernel.org> Cc: Suren Baghdasaryan <surenb@google.com> Link: https://lore.kernel.org/20250612093408.3b7320fa@batman.local.home Fixes: a60b890f607d ("binder: remove global binder lock") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Carlos Llamas <cmllamas@google.com> Reviewed-by: Alice Ryhl <aliceryhl@google.com>
2025-07-23PCI: Fix typosBjorn Helgaas3-3/+3
Fix typos. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Link: https://patch.msgid.link/20250722213743.2822761-1-helgaas@kernel.org
2025-07-23rtc: pcf85063: add support for RV8063Antoni Pokusinski2-10/+98
Microcrystal RV8063 is a real-time clock with SPI interface. Its functionality is very similar to the RV8263 rtc. Signed-off-by: Antoni Pokusinski <apokusinski01@gmail.com> Link: https://lore.kernel.org/r/20250413130755.159373-4-apokusinski01@gmail.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2025-07-23rtc: pcf85063: create pcf85063_i2c_probeAntoni Pokusinski1-27/+70
Move the i2c-specific code from pcf85063_probe to the newly created function. This is a preparation for introducing the support for RV8063 real-time clock with SPI interface. Signed-off-by: Antoni Pokusinski <apokusinski01@gmail.com> Link: https://lore.kernel.org/r/20250413130755.159373-3-apokusinski01@gmail.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2025-07-23PCI: mvebu: Use devm_add_action_or_reset() instead of devm_add_action()Salah Triki1-4/+2
Replace devm_add_action() with devm_add_action_or_reset() to avoid explicitly dropping the 'port->clk' reference in error path. Signed-off-by: Salah Triki <salah.triki@gmail.com> [mani: reworded commit subject and description] Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Link: https://patch.msgid.link/aHsgYALHfQbrgq0t@pc
2025-07-23Bluetooth: btintel_pcie: Fix Alive Context State HandlingKiran K1-55/+62
The firmware raises an alive interrupt upon sending the HCI_RESET or BTINTEL_HCI_OP_RESET command. As part of handling the reset command, firmware initializes the hardware and data path and raises the alive interrupt. Upon receiving the alive interrupt, the driver must enable the data path and grant RX buffers to the firmware before sending any commands. The alive context maintained in the driver must be updated before sending BTINTEL_HCI_OP_RESET or HCI_OP_RESET to prevent a potential race condition where the context is also updated in the threaded IRQ. The issue was observed in a stress reboot usecase (1/25) using "sudo reboot" command where the firmware download was failing as the driver was not granting RX buffer to firmware due to race condition. Bluetooth: hci0: API lock is disabled Bluetooth: hci0: Debug lock is disabled Bluetooth: hci0: Minimum firmware build 1 week 10 2014 Bluetooth: hci0: Bootloader timestamp 2023.43 buildtype 1 build 11631 Bluetooth: hci0: Found device firmware: intel/ibt-00a0-00a1-iml.sfi Bluetooth: hci0: Boot Address: 0xb0301000 Bluetooth: hci0: Firmware Version: 167-12.25 Bluetooth: hci0: Waiting for firmware download to complete Bluetooth: hci0: Firmware loaded in 99902 usecs Bluetooth: hci0: Alive context: fw_dl old_boot_stage: 0xa0db0003 new_boot_stage: 0xa0db0003 Bluetooth: hci0: sent cmd: 0xfc01 alive context changed: fw_dl -> intel_reset1 Bluetooth: hci0: Waiting for device to boot Bluetooth: hci0: Device boot timeout Bluetooth: hci0: Firmware download retry count: 1 Fixes: 05c200c8f029 ("Bluetooth: btintel_pcie: Add handshake between driver and firmware") Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btintel_pcie: Make driver wait for alive interruptKiran K1-13/+17
The firmware raises an alive interrupt upon receiving the HCI_RESET or BTINTEL_HCI_OP_RESET (Intel reset - 0xfc01) command. This change fixes the driver to properly wait for the alive interrupt to avoid driver sending commands to firmware before it is ready to process. For details on the handshake between the driver and firmware, refer to commit 05c200c8f029 ("Bluetooth: btintel_pcie: Add handshake between driver and firmware"). As the driver needs to handle two interrupts for HCI_OP_RESET and BTINTEL_HCI_OP_RESET, the firmware ensures that the TX completion interrupt is always followed by the alive interrupt. Fixes: 05c200c8f029 ("Bluetooth: btintel_pcie: Add handshake between driver and firmware") Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btusb: Add one more ID 0x28de:0x1401 for Qualcomm WCN6855Zijun Hu1-0/+2
Add one more part with ID (0x28de, 0x1401) to usb_device_id table for Qualcomm WCN6855, and its device info from /sys/kernel/debug/usb/devices is shown below: T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=03 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=28de ProdID=1401 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <Zijun.Hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btusb: Sort WCN6855 device IDs by VID and PIDZijun Hu1-34/+34
Sort WCN6855 device IDs to more easily manage them. Signed-off-by: Zijun Hu <Zijun.Hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btusb: QCA: Support downloading custom-made firmwaresZijun Hu1-5/+49
There are custom-made firmwares based on board ID for a given QCA BT chip sometimes, and they are different with existing firmwares and put in a separate subdirectory to avoid conflict, for example: QCA2066, as a variant of WCN6855, has firmwares under 'qca/QCA2066/' of linux-firmware repository. Support downloading custom-made firmwares based on a table newly added. Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btnxpuart: Add uevents for FW dump and FW download completeNeeraj Sanjay Kale1-1/+41
This adds uevents which will be generated whenever FW dump is triggered, FW dump is complete and FW (re)download is done. This feature is needed for IW612 chipset, which is a tri-radio chipset, where WLAN runs on CPU1 and BT and Zigbee runs on CPU2. Currently, whenever BT FW crashes, and FW dump is in progress, there is no way for 15.4 application to know that CPU2 is in bad state, and when it will be recovered. With the help of these uevents and udev rules, the 15.4 app, or any userspace application can be alerted whenever CPU2 goes in bad state and recoveres after BTNXPUART reloads the firmware. [ 334.255154] Bluetooth: hci0: ==== Start FW dump === [ 334.261003] Bluetooth: hci0: ==== Send uevent: BTNXPUART_DEV=serial0-0:BTNXPUART_STATE=FW_DUMP_ACTIVE === [ 351.486048] Bluetooth: hci0: ==== FW dump complete === [ 351.491356] Bluetooth: hci0: ==== Send uevent: BTNXPUART_DEV=serial0-0:BTNXPUART_STATE=FW_DUMP_DONE === [ 352.028974] Bluetooth: hci0: ChipID: 7601, Version: 0 [ 352.034490] Bluetooth: hci0: Request Firmware: nxp/uartspi_n61x_v1.bin.se [ 353.979977] Bluetooth: hci0: FW Download Complete: 417064 bytes [ 355.197222] Bluetooth: hci0: ==== Send uevent: BTNXPUART_DEV=serial0-0:BTNXPUART_STATE=FW_READY === Tested this change by creating a simple udev rule to store the BTNXPUART_STATE value in a ~/<BTNXPUART_DEV>/state file, and running 15.4 traffic. The 15.4 packets were sent over SPI only when BTNXPUART_STATE was FW_READY. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Tested-by: Jean-Yves Salaün <jean-yves.salaun@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btnxpuart: Correct the Independent Reset handling after FW dumpNeeraj Sanjay Kale1-9/+26
This adds proper handling for the independent reset command sent by the driver after FW dump is complete. In normal scenario, the independent reset vendor command gives a success response before jumping to bootcode. However, when FW goes in a bad state, and sends out FW dump packets, the independent reset command does not get any response from the controller. [ 159.807732] Bluetooth: hci0: ==== Start FW dump === [ 180.759060] Bluetooth: hci0: ==== FW dump complete === [ 182.779208] Bluetooth: hci0: command 0xfcfc tx timeout [ 183.364974] Bluetooth: hci0: ChipID: 7601, Version: 0 [ 183.368490] Bluetooth: hci0: Request Firmware: nxp/uartspi_n61x_v1.bin.se [ 184.679977] Bluetooth: hci0: FW Download Complete: 417064 bytes [ 187.963102] Bluetooth: hci0: Opcode 0x0c03 failed: -110 As a fix for such scenario, the independent reset vendor command is sent using the __hci_cmd_send() API, which does not expect any response for vendor commands. __hci_cmd_send is non blocking, so before the tx_work is scheduled, it sometimes gets canceled and 3F|FC command is never sent. Adding a small delay after __hci_cmd_send allows the command to be sent to the controller. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Tested-by: Jean-Yves Salaün <jean-yves.salaun@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btintel: Define a macro for Intel Reset vendor commandKiran K5-17/+19
Use macro for Intel Reset command (0xfc01) instead of hard coded value. Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: hci_bcm4377: Fix typo in commentBastien Nocera1-1/+1
Found by codespell. Signed-off-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btrtl: Fix typo in commentBastien Nocera1-1/+1
Found by codespell. Signed-off-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btmtk: Fix typo in log stringBastien Nocera1-1/+1
Found by codespell. Signed-off-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btintel: Fix typo in commentBastien Nocera1-1/+1
Found by codespell. Signed-off-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btusb: Add new VID/PID 0489/e14e for MT7925En-Wei Wu1-0/+2
Add VID 0489 & PID e14e for MediaTek MT7925 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e14e Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btusb: Add RTL8852BE device 0x13d3:0x3618Hao Li1-0/+2
The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3618 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hao Li <lihao1@uniontech.com> Signed-off-by: WangYuli <wangyuli@uniontech.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btusb: Fix potential NULL dereference on kmalloc failureZhongqiu Han1-0/+2
Avoid potential NULL pointer dereference by checking the return value of kmalloc and handling allocation failure properly. Fixes: 7d70989fcea7 ("Bluetooth: btusb: Add HCI Drv commands for configuring altsetting") Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btnxpuart: implement powerup sequenceCatalin Popescu1-0/+18
NXP bluetooth chip shares power supply and reset gpio with a WLAN chip. Add support for power supply and reset and enforce powerup sequence: - apply power supply - deassert reset/powerdown Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com> Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btnxpuart: Add support for 4M baudrateNeeraj Sanjay Kale1-9/+27
This adds support for 4000000 as secondary baudrate. This value is selected from device tree property "max-speed" which is then used to download FW chunks, and as operational baudrate after HCI initialization is done. Earlier, the secondary baudrate was fixed to 3000000 in driver, but now with "max-speed" property, this secondary baudrate can be set to 4000000. The secondary baudrate is set by the driver by sending a vendor command (3F 09) to the firmware, with secondary baudrate parameter, in nxp_post_init(). Any other value set for max-speed other than 3000000 or 4000000 will default to 3000000, which is supported by all legacy and new NXP chipsets. This feature is applicable for all new V3 bootloader chips and w8987 V1 bootloader chip. This property does not apply for w8997 compatible device, since it downloads a helper.bin FW file that sets secondary baudrate as 3000000 only. The switch to 4000000 baudrate is validated using a Saleae Logic Analyzer and imx8m-mini with AW693 M.2 module. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: hci_qca: Enable ISO data packet RXZijun Hu1-0/+1
Enable ISO data packet RX for LE audio. Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btintel_pcie: Add support for device 0x4d76Kiran K1-0/+1
lspci -v -k -d 8086:4d76 00:14.7 Bluetooth: Intel Corporation Device 4d76 Subsystem: Intel Corporation Device 0011 Flags: fast devsel, IRQ 255, IOMMU group 12 Memory at 13013328000 (64-bit, non-prefetchable) [disabled] [size=16K] Capabilities: [c8] Power Management version 3 Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [40] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [80] MSI-X: Enable- Count=32 Masked- Capabilities: [100] Latency Tolerance Reporting Kernel driver in use: btintel_pcie Kernel modules: btintel_pcie Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btusb: Add a new VID/PID 2c7c/7009 for MT7925Haochen Tong1-0/+2
Adds a new entry with VID 2c7c and PID 7009 for MediaTek MT7925 Bluetooth chip. The device information from /sys/kernel/debug/usb/devices is provided below. T: Bus=03 Lev=01 Prnt=01 Port=04 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=7009 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Haochen Tong <i@hexchain.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btintel_pcie: Reword restart to recoveryLuiz Augusto von Dentz1-38/+33
This rewords the term restart with recovery since the intend is for hardware recovery not a regular restart, also remove some debug logs which might just clutter the output informing the recovery counter which isn't really useful for regular users. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btintel_pcie: Support Function level resetChandrashekar Devegowda2-3/+227
The driver supports Function Level Reset (FLR) to recover the controller upon hardware exceptions or hci command timeouts. FLR is triggered only when no prior reset has occurred within the retry window, with a maximum of one FLR allowed within this window. This patch is tested by, echo 1 > /sys/class/bluetooth/hciX/reset Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btusb: Add support for variant of RTL8851BE (USB ID 13d3:3601)Uwe Kleine-König1-0/+1
Teach the btusb driver to recognize another variant of the RTL8851BE bluetooth radio. /sys/kernel/debug/usb/devices reports for that device: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3601 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Reported-by: shdeb <shdeb3000000@gmail.com> Link: https://bugs.debian.org/1106386 Signed-off-by: Uwe Kleine-König <ukleinek@debian.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23Bluetooth: btusb: Add USB ID 3625:010b for TP-LINK Archer TX10UB NanoZenm Chen1-0/+4
Add USB ID 3625:010b for TP-LINK Archer TX10UB Nano which is based on a Realtek RTL8851BU chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 9 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=3625 ProdID=010b Rev= 0.00 S: Manufacturer=Realtek S: Product=802.11ax WLAN Adapter S: SerialNumber=00e04c000001 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtl8851bu E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Cc: stable@vger.kernel.org Signed-off-by: Zenm Chen <zenmchen@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-07-23drm/i915/display: Fix dma_fence_wait_timeout() return value handlingAakash Deep Sarkar1-1/+2
dma_fence_wait_timeout returns a long type but the driver is only using the lower 32 bits of the retval and discarding the upper 32 bits. This is particularly problematic if there are already signalled or stub fences on some of the hw planes. In this case the dma_fence_wait_timeout function will immediately return with timeout value MAX_SCHEDULE_TIMEOUT (0x7fffffffffffffff) since the fence is already signalled. If the driver only uses the lower 32 bits of this return value then it'll interpret it as an error code (0xFFFFFFFF or (-1)) and skip the wait on the remaining fences. This issue was first observed in the xe driver with the Android compositor where the GPU composited layer was not properly waited on when there were stub fences in other overlay planes resulting in visual artifacts. Fixes: d59cf7bb73f3c ("drm/i915/display: Use dma_fence interfaces instead of i915_sw_fence") Signed-off-by: Aakash Deep Sarkar <aakash.deep.sarkar@intel.com> Reviewed-by: Matthew Brost <matthew.brost@intel.com> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Link: https://lore.kernel.org/r/20250708074540.1948068-1-aakash.deep.sarkar@intel.com (cherry picked from commit cdb16039515a5ac4d2c923f7a651cf19a803a3fe) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
2025-07-23dmaengine: xdmac: make it selectable for ARCH_MICROCHIPRobert Marko1-1/+1
LAN969x uses the Atmel XDMAC, so make it selectable for ARCH_MICROCHIP to avoid needing to update depends in future if other Microchip SoC-s use it as well. Signed-off-by: Robert Marko <robert.marko@sartura.hr> Link: https://lore.kernel.org/r/20250702183856.1727275-9-robert.marko@sartura.hr Signed-off-by: Vinod Koul <vkoul@kernel.org>
2025-07-23dmaengine: nbpfaxi: Add missing check after DMA mapThomas Fourier1-0/+13
The DMA map functions can fail and should be tested for errors. If the mapping fails, unmap and return an error. Fixes: b45b262cefd5 ("dmaengine: add a driver for AMBA AXI NBPF DMAC IP cores") Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com> Link: https://lore.kernel.org/r/20250707075752.28674-2-fourier.thomas@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2025-07-23dmaengine: mv_xor: Fix missing check after DMA map and missing unmapThomas Fourier1-2/+19
The DMA map functions can fail and should be tested for errors. In case of error, unmap the already mapped regions. Fixes: 22843545b200 ("dma: mv_xor: Add support for DMA_INTERRUPT") Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com> Link: https://lore.kernel.org/r/20250701123753.46935-2-fourier.thomas@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2025-07-23Merge tag 'iwlwifi-next-2025-07-23' of ↵Johannes Berg34-678/+443
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next Miri Korenblit says: ==================== iwlwifi feature, notably - disable features in fips - remove RX OMI feature code - A few fixes and cleanups ==================== Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2025-07-23wifi: brcmsmac: Use str_true_false() helperLiu Song1-9/+10
Remove hard-coded strings by using the str_true_false() helper function. Signed-off-by: Liu Song <liu.song13@zte.com.cn> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>> Link: https://patch.msgid.link/20250723173004776P6QSjcW7NrlpGYLTFM-yP@zte.com.cn Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2025-07-23wifi: brcmfmac: fix EXTSAE WPA3 connection failure due to AUTH TX failureTing-Ying Li2-21/+35
For WPA3-SAE Connection in EXTSAE mode, the userspace daemon is allowed to generate the SAE Auth frames. The driver uses the "mgmt_frame" FW IOVAR to transmit this MGMT frame. Before sending the IOVAR, the Driver is incorrectly treating the channel number read from the FW as a frequency value and again attempts to convert this into a channel number using ieee80211_frequency_to_channel(). This added an invalid channel number as part of the IOVAR request to the FW And some FW which strictly expects a valid channel would return BAD_CHAN error, while failing to transmit the driver requested SAE Auth MGMT frame. Fix this in the CYW vendor specific MGMT TX cfg80211 ops handler, by not treating the channel number read from the FW as frequency value and skip the attempt to convert it again into a channel number. Also fix this in the generic MGMT TX cfg80211 ops handler. Fixes: c2ff8cad6423 ("brcm80211: make mgmt_tx in brcmfmac accept a NULL channel") Fixes: 66f909308a7c ("wifi: brcmfmac: cyw: support external SAE authentication in station mode") Signed-off-by: Ting-Ying Li <tingying.li@cypress.com> Signed-off-by: Gokul Sivakumar <gokulkumar.sivakumar@infineon.com> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>> Link: https://patch.msgid.link/20250723105918.5229-1-gokulkumar.sivakumar@infineon.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2025-07-23wifi: brcm80211: Remove yet more unused functionsDr. David Alan Gilbert3-136/+0
This is a subset of unused functions in bcrmsmac phy_cmn.c, They're unused since the original 2010 commit a9533e7ea3c4 ("Staging: Add initial release of brcm80211 - Broadcom 802.11n wireless LAN driver.") Remove them. Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>> Link: https://patch.msgid.link/20250626140812.56700-4-linux@treblig.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2025-07-23wifi: brcm80211: Remove more unused functionsDr. David Alan Gilbert2-198/+0
This is a subset of unused functions in bcrmsmac phy_cmn.c, They're unused since the original 2010 commit a9533e7ea3c4 ("Staging: Add initial release of brcm80211 - Broadcom 802.11n wireless LAN driver.") Remove them. Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>> Link: https://patch.msgid.link/20250626140812.56700-3-linux@treblig.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2025-07-23wifi: brcm80211: Remove unused functionsDr. David Alan Gilbert4-166/+0
This is a subset of unused functions in bcrmsmac phy_cmn.c, They're unused since the original 2010 commit a9533e7ea3c4 ("Staging: Add initial release of brcm80211 - Broadcom 802.11n wireless LAN driver.") Remove them. Then remove two more functions in phy_n.c that were only used by the ones just removed. Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>> Link: https://patch.msgid.link/20250626140812.56700-2-linux@treblig.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2025-07-23spi: spi-qpic-snand: simplify bad block marker duplicationGabor Juhos1-4/+10
Due to the expectations of the SPINAND code, the driver duplicates the bad block markers during raw OOB reads. It has been implemented by using two if statements, and due to the opposite conditions one of conditional codepaths always runs. Since the effect of both codepaths is the same, remove the if statements and use a single line solution instead. Also add a note about why the duplication is required. No functional changes intended. Signed-off-by: Gabor Juhos <j4g8y7@gmail.com> Link: https://patch.msgid.link/20250711-qpic-snand-simplify-bbm-copy-v1-1-dd2608325f72@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
2025-07-23spi: spi-qpic-snand: don't hardcode ECC stepsGabor Juhos1-1/+1
NAND devices with different page sizes requires different number of ECC steps, yet the qcom_spi_ecc_init_ctx_pipelined() function sets 4 steps in 'ecc_cfg' unconditionally. The correct number of the steps is calculated earlier in the function already, so use that instead of the hardcoded value. Fixes: 7304d1909080 ("spi: spi-qpic: add driver for QCOM SPI NAND flash Interface") Signed-off-by: Gabor Juhos <j4g8y7@gmail.com> Link: https://patch.msgid.link/20250723-qpic-snand-fix-steps-v1-1-d800695dde4c@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
2025-07-23iommu/vt-d: Fix UAF on sva unbind with pending IOPFsLu Baolu1-1/+1
Commit 17fce9d2336d ("iommu/vt-d: Put iopf enablement in domain attach path") disables IOPF on device by removing the device from its IOMMU's IOPF queue when the last IOPF-capable domain is detached from the device. Unfortunately, it did this in a wrong place where there are still pending IOPFs. As a result, a use-after-free error is potentially triggered and eventually a kernel panic with a kernel trace similar to the following: refcount_t: underflow; use-after-free. WARNING: CPU: 3 PID: 313 at lib/refcount.c:28 refcount_warn_saturate+0xd8/0xe0 Workqueue: iopf_queue/dmar0-iopfq iommu_sva_handle_iopf Call Trace: <TASK> iopf_free_group+0xe/0x20 process_one_work+0x197/0x3d0 worker_thread+0x23a/0x350 ? rescuer_thread+0x4a0/0x4a0 kthread+0xf8/0x230 ? finish_task_switch.isra.0+0x81/0x260 ? kthreads_online_cpu+0x110/0x110 ? kthreads_online_cpu+0x110/0x110 ret_from_fork+0x13b/0x170 ? kthreads_online_cpu+0x110/0x110 ret_from_fork_asm+0x11/0x20 </TASK> ---[ end trace 0000000000000000 ]--- The intel_pasid_tear_down_entry() function is responsible for blocking hardware from generating new page faults and flushing all in-flight ones. Therefore, moving iopf_for_domain_remove() after this function should resolve this. Fixes: 17fce9d2336d ("iommu/vt-d: Put iopf enablement in domain attach path") Reported-by: Ethan Milon <ethan.milon@eviden.com> Closes: https://lore.kernel.org/r/e8b37f3e-8539-40d4-8993-43a1f3ffe5aa@eviden.com Suggested-by: Ethan Milon <ethan.milon@eviden.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/20250723072045.1853328-1-baolu.lu@linux.intel.com Signed-off-by: Will Deacon <will@kernel.org>
2025-07-23pinctrl: mediatek: Add pinctrl driver for mt8189Cathy Xu4-0/+4165
Add pinctrl driver support for MediaTek Soc mt8189. Signed-off-by: Cathy Xu <ot_cathy.xu@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/20250711094513.17073-4-ot_cathy.xu@mediatek.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2025-07-23pinctrl: aspeed-g6: Add PCIe RC PERST pin groupJacky Chou1-1/+11
The PCIe RC PERST uses SSPRST# as PERST# and enable this pin to output. Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/20250715034320.2553837-8-jacky_chou@aspeedtech.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2025-07-23xen/netfront: Fix TX response spurious interruptsAnthoine Bourgeois1-5/+0
We found at Vates that there are lot of spurious interrupts when benchmarking the xen-net PV driver frontend. This issue appeared with a patch that addresses security issue XSA-391 (b27d47950e48 "xen/netfront: harden netfront against event channel storms"). On an iperf benchmark, spurious interrupts can represent up to 50% of the interrupts. Spurious interrupts are interrupts that are rised for nothing, there is no work to do. This appends because the function that handles the interrupts ("xennet_tx_buf_gc") is also called at the end of the request path to garbage collect the responses received during the transmission load. The request path is doing the work that the interrupt handler should have done otherwise. This is particurary true when there is more than one vcpu and get worse linearly with the number of vcpu/queue. Moreover, this problem is amplifyed by the penalty imposed by a spurious interrupt. When an interrupt is found spurious the interrupt chip will delay the EOI to slowdown the backend. This delay will allow more responses to be handled by the request path and then there will be more chance the next interrupt will not find any work to do, creating a new spurious interrupt. This causes performance issue. The solution here is to remove the calls from the request path and let the interrupt handler do the processing of the responses. This approch removes most of the spurious interrupts (<0.05%) and also has the benefit of freeing up cycles in the request path, allowing it to process more work, which improves performance compared to masking the spurious interrupt one way or another. This optimization changes a part of the code that is present since the net frontend driver was upstreamed. There is no similar pattern in the other xen PV drivers. Since the first commit of xen-netfront is a blob that doesn't explain all the design choices I can only guess why this specific mecanism was here. This could have been introduce to compensate a slow backend at the time (maybe the backend was fixed or optimize later) or a small queue. In 18 years, both frontend and backend gain lot of features and optimizations that could have obsolete the feature of reaping completions from the TX path. Some vif throughput performance figures from a 8 vCPUs, 4GB of RAM HVM guest(s): Without this patch on the : vm -> dom0: 4.5Gb/s vm -> vm: 7.0Gb/s Without XSA-391 patch (revert of b27d47950e48): vm -> dom0: 8.3Gb/s vm -> vm: 8.7Gb/s With XSA-391 and this patch: vm -> dom0: 11.5Gb/s vm -> vm: 12.6Gb/s v2: - add revewed and tested by tags - resend with the maintainers in the recipients list v3: - remove Fixes tag but keep the commit ref in the explanation - add a paragraph on why this code was here Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@vates.tech> Reviewed-by: Juergen Gross <jgross@suse.com> Tested-by: Elliott Mitchell <ehem+xen@m5p.com> Signed-off-by: Juergen Gross <jgross@suse.com> Message-ID: <20250721093316.23560-1-anthoine.bourgeois@vates.tech>
2025-07-23wifi: iwlwifi: Revert "wifi: iwlwifi: remove support of several ↵Miri Korenblit2-10/+30
iwl_ppag_table_cmd versions" It turns out that version 6 is still needed. This change will be brought back once the FW that supports version 6 will no longer be supported. This reverts commit 24bc49d158c7 ("wifi: iwlwifi: remove support of several iwl_ppag_table_cmd versions") Link: https://patch.msgid.link/20250723064515.2084903-2-miriam.rachel.korenblit@intel.com Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-11 11:34:24 +0300