| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit 004d25060c78 ("igb: Fix igb_down hung on surprise removal")
changed igb_io_error_detected() to ignore non-fatal pcie errors in order
to avoid hung task that can happen when igb_down() is called multiple
times. This caused an issue when processing transient non-fatal errors.
igb_io_resume(), which is called after igb_io_error_detected(), assumes
that device is brought down by igb_io_error_detected() if the interface
is up. This resulted in panic with stacktrace below.
[ T3256] igb 0000:09:00.0 haeth0: igb: haeth0 NIC Link is Down
[ T292] pcieport 0000:00:1c.5: AER: Uncorrected (Non-Fatal) error received: 0000:09:00.0
[ T292] igb 0000:09:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID)
[ T292] igb 0000:09:00.0: device [8086:1537] error status/mask=00004000/00000000
[ T292] igb 0000:09:00.0: [14] CmpltTO [ 200.105524,009][ T292] igb 0000:09:00.0: AER: TLP Header: 00000000 00000000 00000000 00000000
[ T292] pcieport 0000:00:1c.5: AER: broadcast error_detected message
[ T292] igb 0000:09:00.0: Non-correctable non-fatal error reported.
[ T292] pcieport 0000:00:1c.5: AER: broadcast mmio_enabled message
[ T292] pcieport 0000:00:1c.5: AER: broadcast resume message
[ T292] ------------[ cut here ]------------
[ T292] kernel BUG at net/core/dev.c:6539!
[ T292] invalid opcode: 0000 [#1] PREEMPT SMP
[ T292] RIP: 0010:napi_enable+0x37/0x40
[ T292] Call Trace:
[ T292] <TASK>
[ T292] ? die+0x33/0x90
[ T292] ? do_trap+0xdc/0x110
[ T292] ? napi_enable+0x37/0x40
[ T292] ? do_error_trap+0x70/0xb0
[ T292] ? napi_enable+0x37/0x40
[ T292] ? napi_enable+0x37/0x40
[ T292] ? exc_invalid_op+0x4e/0x70
[ T292] ? napi_enable+0x37/0x40
[ T292] ? asm_exc_invalid_op+0x16/0x20
[ T292] ? napi_enable+0x37/0x40
[ T292] igb_up+0x41/0x150
[ T292] igb_io_resume+0x25/0x70
[ T292] report_resume+0x54/0x70
[ T292] ? report_frozen_detected+0x20/0x20
[ T292] pci_walk_bus+0x6c/0x90
[ T292] ? aer_print_port_info+0xa0/0xa0
[ T292] pcie_do_recovery+0x22f/0x380
[ T292] aer_process_err_devices+0x110/0x160
[ T292] aer_isr+0x1c1/0x1e0
[ T292] ? disable_irq_nosync+0x10/0x10
[ T292] irq_thread_fn+0x1a/0x60
[ T292] irq_thread+0xe3/0x1a0
[ T292] ? irq_set_affinity_notifier+0x120/0x120
[ T292] ? irq_affinity_notify+0x100/0x100
[ T292] kthread+0xe2/0x110
[ T292] ? kthread_complete_and_exit+0x20/0x20
[ T292] ret_from_fork+0x2d/0x50
[ T292] ? kthread_complete_and_exit+0x20/0x20
[ T292] ret_from_fork_asm+0x11/0x20
[ T292] </TASK>
To fix this issue igb_io_resume() checks if the interface is running and
the device is not down this means igb_io_error_detected() did not bring
the device down and there is no need to bring it up.
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Reviewed-by: Yuanyuan Zhong <yzhong@purestorage.com>
Fixes: 004d25060c78 ("igb: Fix igb_down hung on surprise removal")
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This patch addresses a macvlan leak issue in the i40e driver caused by
concurrent access to vsi->mac_filter_hash. The leak occurs when multiple
threads attempt to modify the mac_filter_hash simultaneously, leading to
inconsistent state and potential memory leaks.
To fix this, we now wrap the calls to i40e_del_mac_filter() and zeroing
vf->default_lan_addr.addr with spin_lock/unlock_bh(&vsi->mac_filter_hash_lock),
ensuring atomic operations and preventing concurrent access.
Additionally, we add lockdep_assert_held(&vsi->mac_filter_hash_lock) in
i40e_add_mac_filter() to help catch similar issues in the future.
Reproduction steps:
1. Spawn VFs and configure port vlan on them.
2. Trigger concurrent macvlan operations (e.g., adding and deleting
portvlan and/or mac filters).
3. Observe the potential memory leak and inconsistent state in the
mac_filter_hash.
This synchronization ensures the integrity of the mac_filter_hash and prevents
the described leak.
Fixes: fed0d9f13266 ("i40e: Fix VF's MAC Address change on VM")
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Increasing MSI-X value on a VF leads to invalid memory operations. This
is caused by not reallocating some arrays.
Reproducer:
modprobe ice
echo 0 > /sys/bus/pci/devices/$PF_PCI/sriov_drivers_autoprobe
echo 1 > /sys/bus/pci/devices/$PF_PCI/sriov_numvfs
echo 17 > /sys/bus/pci/devices/$VF0_PCI/sriov_vf_msix_count
Default MSI-X is 16, so 17 and above triggers this issue.
KASAN reports:
BUG: KASAN: slab-out-of-bounds in ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
Read of size 8 at addr ffff8888b937d180 by task bash/28433
(...)
Call Trace:
(...)
? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
kasan_report+0xed/0x120
? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
ice_vsi_cfg_def+0x3360/0x4770 [ice]
? mutex_unlock+0x83/0xd0
? __pfx_ice_vsi_cfg_def+0x10/0x10 [ice]
? __pfx_ice_remove_vsi_lkup_fltr+0x10/0x10 [ice]
ice_vsi_cfg+0x7f/0x3b0 [ice]
ice_vf_reconfig_vsi+0x114/0x210 [ice]
ice_sriov_set_msix_vec_count+0x3d0/0x960 [ice]
sriov_vf_msix_count_store+0x21c/0x300
(...)
Allocated by task 28201:
(...)
ice_vsi_cfg_def+0x1c8e/0x4770 [ice]
ice_vsi_cfg+0x7f/0x3b0 [ice]
ice_vsi_setup+0x179/0xa30 [ice]
ice_sriov_configure+0xcaa/0x1520 [ice]
sriov_numvfs_store+0x212/0x390
(...)
To fix it, use ice_vsi_rebuild() instead of ice_vf_reconfig_vsi(). This
causes the required arrays to be reallocated taking the new queue count
into account (ice_vsi_realloc_stat_arrays()). Set req_txq and req_rxq
before ice_vsi_rebuild(), so that realloc uses the newly set queue
count.
Additionally, ice_vsi_rebuild() does not remove VSI filters
(ice_fltr_remove_all()), so ice_vf_init_host_cfg() is no longer
necessary.
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Fixes: 2a2cb4c6c181 ("ice: replace ice_vf_recreate_vsi() with ice_vf_reconfig_vsi()")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Triggering the reset while in switchdev mode causes
errors[1]. Rules are already removed by this time
because switch content is flushed in case of the reset.
This means that rules were deleted from HW but SW
still thinks they exist so when we get
SWITCHDEV_FDB_DEL_TO_DEVICE notification we try to
delete not existing rule.
We can avoid these errors by clearing the rules
early in the reset flow before they are removed from HW.
Switchdev API will get notified that the rule was removed
so we won't get SWITCHDEV_FDB_DEL_TO_DEVICE notification.
Remove unnecessary ice_clear_sw_switch_recipes.
[1]
ice 0000:01:00.0: Failed to delete FDB forward rule, err: -2
ice 0000:01:00.0: Failed to delete FDB guard rule, err: -2
Fixes: 7c945a1a8e5f ("ice: Switchdev FDB events support")
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
netif_is_ice() works by checking the pointer to netdev ops. However, it
only checks for the default ice_netdev_ops, not ice_netdev_safe_mode_ops,
so in Safe Mode it always returns false, which is unintuitive. While it
doesn't look like netif_is_ice() is currently being called anywhere in Safe
Mode, this could change and potentially lead to unexpected behaviour.
Fixes: df006dd4b1dc ("ice: Add initial support framework for LAG")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If DDP package is missing or corrupted, the driver should enter Safe Mode.
Instead, an error is returned and probe fails.
To fix this, don't exit init if ice_init_ddp_config() returns an error.
Repro:
* Remove or rename DDP package (/lib/firmware/intel/ice/ddp/ice.pkg)
* Load ice
Fixes: cc5776fe1832 ("ice: Enable switching default Tx scheduler topology")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/video/fbdev to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
While touching these files, make indention of the struct initializer
consistent in several files.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Similar to the MSR RAPL interface, MMIO RAPL supports PL4 too, so add
MMIO RAPL PL4d support to the processor_thermal driver.
As a result, the powercap sysfs for MMIO RAPL will show a new "peak
power" constraint.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240930081801.28502-7-rui.zhang@intel.com
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
CPU0/package0 is always online and the MMIO RAPL driver runs on single
package systems only, so there is no need to handle CPU hotplug in it.
Always register a RAPL package device for package 0 and remove the
unnecessary CPU hotplug support.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240930081801.28502-6-rui.zhang@intel.com
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add PL4 support for ArrowLake-U platform.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240930081801.28502-5-rui.zhang@intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The hardware definition of every TPMI feature contains a major and minor
version. When there is a change in the MMIO offset or change in the
definition of a field, hardware will change major version. For addition
of new fields without modifying existing MMIO offsets or fields, only
the minor version is changed.
If the driver has not been updated to recognize a new hardware major
version, it cannot provide the RAPL interface to users due to possible
register layout incompatibilities. However, the driver does not need to
be updated every time the hardware minor version changes because in that
case it will just miss some new functionality exposed by the hardware.
The current implementation causes the driver to refuse to work for any
hardware version change which is unnecessarily restrictive.
If there is a minor version mismatch, log an information message and
continue, but if there is a major version mismatch, log a warning and
exit (as before).
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240930081801.28502-4-rui.zhang@intel.com
Fixes: 9eef7f9da928 ("powercap: intel_rapl: Introduce RAPL TPMI interface driver")
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make sure to always set the GEM function pointer even for in kernel
allocations. This fixes a NULL pointer deref caused by switching to GEM
references.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: fd69ef05029f ("drm/radeon: use GEM references instead of TTMs")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 01b64bc063d014641631867a7e0edd8ac55282d4)
|
|
Replace of_clk_get with devm_clk_get_enabled to manage the clock source.
Fixes: 5ae4cb94b313 ("gpio: aspeed: Add debounce support")
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20241008081450.1490955-3-billy_tsai@aspeedtech.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Performing a dummy read ensures that the register write operation is fully
completed, mitigating any potential bus delays that could otherwise impact
the frequency of bitbang usage. E.g., if the JTAG application uses GPIO to
control the JTAG pins (TCK, TMS, TDI, TDO, and TRST), and the application
sets the TCK clock to 1 MHz, the GPIO's high/low transitions will rely on
a delay function to ensure the clock frequency does not exceed 1 MHz.
However, this can lead to rapid toggling of the GPIO because the write
operation is POSTed and does not wait for a bus acknowledgment.
Fixes: 361b79119a4b ("gpio: Add Aspeed driver")
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20241008081450.1490955-2-billy_tsai@aspeedtech.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The `nouveau_dmem_copy_one` function ensures that the copy push command is
sent to the device firmware but does not track whether it was executed
successfully.
In the case of a copy error (e.g., firmware or hardware failure), the
copy push command will be sent via the firmware channel, and
`nouveau_dmem_copy_one` will likely report success, leading to the
`migrate_to_ram` function returning a dirty HIGH_USER page to the user.
This can result in a security vulnerability, as a HIGH_USER page that may
contain sensitive or corrupted data could be returned to the user.
To prevent this vulnerability, we allocate a zero page. Thus, in case of
an error, a non-dirty (zero) page will be returned to the user.
Fixes: 5be73b690875 ("drm/nouveau/dmem: device memory helpers for SVM")
Signed-off-by: Yonatan Maman <Ymaman@Nvidia.com>
Co-developed-by: Gal Shalom <GalShalom@Nvidia.com>
Signed-off-by: Gal Shalom <GalShalom@Nvidia.com>
Reviewed-by: Ben Skeggs <bskeggs@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241008115943.990286-3-ymaman@nvidia.com
|
|
When `nouveau_dmem_copy_one` is called, the following error occurs:
[272146.675156] nouveau 0000:06:00.0: fifo: PBDMA9: 00000004 [HCE_PRIV]
ch 1 00000300 00003386
This indicates that a copy push command triggered a Host Copy Engine
Privileged error on channel 1 (Copy Engine channel). To address this
issue, modify the Copy Engine channel to allow privileged push commands
Fixes: 6de125383a5c ("drm/nouveau/fifo: expose runlist topology info on all chipsets")
Signed-off-by: Yonatan Maman <Ymaman@Nvidia.com>
Co-developed-by: Gal Shalom <GalShalom@Nvidia.com>
Signed-off-by: Gal Shalom <GalShalom@Nvidia.com>
Reviewed-by: Ben Skeggs <bskeggs@nvidia.com>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241008115943.990286-2-ymaman@nvidia.com
|
|
All modern chips support and need the 10_100 bit set for supporting jumbo
frames on 10/100 ports, so instead of enabling it only for 583XX enable
it for everything except bcm63xx, where the bit is writeable, but does
nothing.
Tested on BCM53115, where jumbo frames were dropped at 10/100 speeds
without the bit set.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
While BCM5325/5365 do not support jumbo frames, they do support slightly
oversized frames, so do not error out if requesting a supported MTU for
them.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
BCM5325/BCM5365 do not support jumbo frames, so we should not report a
jumbo frame mtu for them. But they do support so called "oversized"
frames up to 1536 bytes long by default, so report an appropriate MTU.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Usage of devm_alloc_etherdev_mqs() conflicts with
am65_cpsw_nuss_cleanup_ndev() as the same struct net_device instances
get unregistered twice. Switch to alloc_etherdev_mqs() and make sure
am65_cpsw_nuss_cleanup_ndev() unregisters and frees those net_device
instances properly.
With this, it is finally possible to rmmod the driver without oopsing
the kernel.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Roger Quadros <roger@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In am65_cpsw_nuss_remove(), move the call to am65_cpsw_unregister_devlink()
after am65_cpsw_nuss_cleanup_ndev() to avoid triggering the
WARN_ON(devlink_port->type != DEVLINK_PORT_TYPE_NOTSET) in
devl_port_unregister(). Makes it coherent with usage in
m65_cpsw_nuss_register_ndevs()'s cleanup path.
Fixes: 58356eb31d60 ("net: ti: am65-cpsw-nuss: Add devlink support")
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move the tx cpu dma ring index update out of transmit loop of
airoha_dev_xmit routine in order to not start transmitting the packet
before it is fully DMA mapped (e.g. fragmented skbs).
Fixes: 23020f049327 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Reported-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241004-airoha-eth-7581-mapping-fix-v1-1-8e4279ab1812@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct
ordering") correctly fixed a problem with using devm_ but missed
removing the LED entry from the LEDs list.
This cause kernel panic on specific scenario where the port for the PHY
is torn down and up and the kmod for the PHY is removed.
On setting the port down the first time, the assosiacted LEDs are
correctly unregistered. The associated kmod for the PHY is now removed.
The kmod is now added again and the port is now put up, the associated LED
are registered again.
On putting the port down again for the second time after these step, the
LED list now have 4 elements. With the first 2 already unregistered
previously and the 2 new one registered again.
This cause a kernel panic as the first 2 element should have been
removed.
Fix this by correctly removing the element when LED is unregistered.
Reported-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Cc: stable@vger.kernel.org
Fixes: c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct ordering")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241004182759.14032-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- RFCOMM: FIX possible deadlock in rfcomm_sk_state_change
- hci_conn: Fix UAF in hci_enhanced_setup_sync
- btusb: Don't fail external suspend requests
* tag 'for-net-2024-10-04' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: btusb: Don't fail external suspend requests
Bluetooth: hci_conn: Fix UAF in hci_enhanced_setup_sync
Bluetooth: RFCOMM: FIX possible deadlock in rfcomm_sk_state_change
====================
Link: https://patch.msgid.link/20241004210124.4010321-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
adin1110_read_fifo()
If 'frame_size' is too small or if 'round_len' is an error code, it is
likely that an error code should be returned to the caller.
Actually, 'ret' is likely to be 0, so if one of these sanity checks fails,
'success' is returned.
Return -EINVAL instead.
Fixes: bc93e19d088b ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/8ff73b40f50d8fa994a454911b66adebce8da266.1727981562.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit b514c47ebf41a6536551ed28a05758036e6eca7c.
The commit describes that we don't have to sync the page when
recycling, and it tries to optimize that case. But we do need
to sync after allocation. Recycling side should be changed to
pass the right sync size instead.
Fixes: b514c47ebf41 ("net: stmmac: set PP_FLAG_DMA_SYNC_DEV only if XDP is enabled")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/20241004070846.2502e9ea@kernel.org
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/20241004142115.910876-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Accessing device registers seems to be not reliable, the chip
revision is sometimes detected wrongly (0 instead of expected 1).
Ensure that the chip reset is performed via reset GPIO and then
wait for 'Device Ready' status in HW_CFG register before doing
any register initializations.
Cc: stable@vger.kernel.org
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
[alex: reworked using read_poll_timeout()]
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20241004113655.3436296-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since, two suspend-resume cycles are required to enter hibernate and,
since we only need to enable idle optimizations in the first cycle
(which is pretty much equivalent to s2idle). We can check in_s0ix, to
prevent the system from entering idle optimizations before it actually
enters hibernate (from display's perspective). Also, call
dc_set_power_state() before dc_allow_idle_optimizations(), since it's
safer to do so because dc_set_power_state() writes to DMUB.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2fe79508d9c393bb9931b0037c5ecaee09a8dc39)
Cc: stable@vger.kernel.org # 6.10+
|
|
[Why]
Since the surface/stream update flags aren't cleared after applying
updates, those same updates may be applied again in a future call to
update surfaces/streams for surfaces/streams that aren't actually part
of that update (i.e. applying an update for one surface/stream can
trigger unintended programming on a different surface/stream).
For example, when an update results in a call to
program_front_end_for_ctx, that function may call program_pipe on all
pipes. If there are surface update flags that were never cleared on the
surface some pipe is attached to, then the same update will be
programmed again.
[How]
Clear the surface and stream update flags after applying the updates.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3441
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3616
Cc: Melissa Wen <mwen@igalia.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7671f62c10f2a4c77d89b39fd50fab7f918d6809)
Cc: stable@vger.kernel.org
|
|
Partially revert
commit 0ca9f757a0e2 ("drm/amd/pm: powerplay: Add `__counted_by` attribute for flexible arrays")
The count attribute for these arrays does not get set until
after the arrays are allocated and populated leading to false
UBSAN warnings.
Fixes: 0ca9f757a0e2 ("drm/amd/pm: powerplay: Add `__counted_by` attribute for flexible arrays")
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3662
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8a5ae927b653b43623e55610d2215ee94c027e8c)
Cc: stable@vger.kernel.org
|
|
The patch is to solve null dereference in 'aux.dev', which is
introduced in recent radeon rework. By having 'late_register',
the connector should be registered after 'drm_dev_register'
automatically, where in before it is the opposite.
Fixes: 90985660ba48 ("drm/radeon: remove load callback from kms_driver")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3665
Tested-by: Hans de Goede <hdegoede@redhat.com>
Suggested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Wu Hoi Pok <wuhoipok@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit b4c1ad70e279bacbc772a468033bdecce2f5e0dc)
|
|
Only creating a new reference for each process instead of each VM.
Fixes: 9a1c1339abf9 ("drm/amdkfd: Run restore_workers on freezable WQs")
Suggested-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 5fa436289483ae56427b0896c31f72361223c758)
Cc: stable@vger.kernel.org
|
|
Pull virtio fixes from Michael Tsirkin:
"Several small bugfixes all over the place.
Most notably, fixes the vsock allocation with GFP_KERNEL in atomic
context, which has been triggering warnings for lots of testers"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost/scsi: null-ptr-dereference in vhost_scsi_get_req()
vsock/virtio: use GFP_ATOMIC under RCU read lock
virtio_console: fix misc probe bugs
virtio_ring: tag event_triggered as racy for KCSAN
vdpa/octeon_ep: Fix format specifier for pointers in debug messages
|
|
The processor_thermal driver uses pcim_device_enable() to enable a PCI
device, which means the device will be automatically disabled on driver
detach. Thus there is no need to call pci_disable_device() again on it.
With recent PCI device resource management improvements, e.g. commit
f748a07a0b64 ("PCI: Remove legacy pcim_release()"), this problem is
exposed and triggers the warining below.
[ 224.010735] proc_thermal_pci 0000:00:04.0: disabling already-disabled device
[ 224.010747] WARNING: CPU: 8 PID: 4442 at drivers/pci/pci.c:2250 pci_disable_device+0xe5/0x100
...
[ 224.010844] Call Trace:
[ 224.010845] <TASK>
[ 224.010847] ? show_regs+0x6d/0x80
[ 224.010851] ? __warn+0x8c/0x140
[ 224.010854] ? pci_disable_device+0xe5/0x100
[ 224.010856] ? report_bug+0x1c9/0x1e0
[ 224.010859] ? handle_bug+0x46/0x80
[ 224.010862] ? exc_invalid_op+0x1d/0x80
[ 224.010863] ? asm_exc_invalid_op+0x1f/0x30
[ 224.010867] ? pci_disable_device+0xe5/0x100
[ 224.010869] ? pci_disable_device+0xe5/0x100
[ 224.010871] ? kfree+0x21a/0x2b0
[ 224.010873] pcim_disable_device+0x20/0x30
[ 224.010875] devm_action_release+0x16/0x20
[ 224.010878] release_nodes+0x47/0xc0
[ 224.010880] devres_release_all+0x9f/0xe0
[ 224.010883] device_unbind_cleanup+0x12/0x80
[ 224.010885] device_release_driver_internal+0x1ca/0x210
[ 224.010887] driver_detach+0x4e/0xa0
[ 224.010889] bus_remove_driver+0x6f/0xf0
[ 224.010890] driver_unregister+0x35/0x60
[ 224.010892] pci_unregister_driver+0x44/0x90
[ 224.010894] proc_thermal_pci_driver_exit+0x14/0x5f0 [processor_thermal_device_pci]
...
[ 224.010921] ---[ end trace 0000000000000000 ]---
Remove the excess pci_disable_device() calls.
Fixes: acd65d5d1cf4 ("thermal/drivers/int340x/processor_thermal: Add PCI MMIO based thermal driver")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240930081801.28502-3-rui.zhang@intel.com
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The TPMI_RAPL_REG_DOMAIN_INFO value needs to be multiplied by 8 to get
the register offset.
Cc: All applicable <stable@vger.kernel.org>
Fixes: 903eb9fb85e3 ("powercap: intel_rapl_tpmi: Fix System Domain probing")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://patch.msgid.link/20240930081801.28502-2-rui.zhang@intel.com
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Asus Vivobook Pro 15 OLED comes in 3 N6506M* models:
N6506MU: Intel Ultra 9 185H, 3K OLED, RTX4060
N6506MV: Intel Ultra 7 155H, 3K OLED, RTX4050
N6506MJ: Intel Ultra 7 155H, FHD OLED, RTX3050
Fold the 3 DMI quirks for these into a single quirk to reduce the number
of quirks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241005212819.354681-5-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Asus has 2 ExpertBook B1402C models:
B1402CBA with 12th gen Intel CPUs
B1402CVA with 13th gen Intel CPUs
Fold the 2 DMI quirks for these into a single quirk to reduce the number
of quirks.
Likewise Asus has 3 ExpertBook B1502C models:
B1502CBA with 12th gen Intel CPUs
B1502CGA with 12th gen Intel N-series CPUs
B1502CVA with 13th gen Intel CPUs
Fold the 3 DMI quirks for these into a single quirk to reduce the number
of quirks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241005212819.354681-4-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Like the various 14" Asus ExpertBook B2 B2402* models there are also
4 variants of the 15" Asus ExpertBook B2 B2502* models:
B2502CBA: 12th gen Intel CPU, non flip
B2502FBA: 12th gen Intel CPU, flip
B2502CVA: 13th gen Intel CPU, non flip
B2502FVA: 13th gen Intel CPU, flip
Currently there already are DMI quirks for the B2502CBA, B2502FBA and
B2502CVA models. Asus website shows that there also is a B2502FVA.
Rather then adding a 4th quirk fold the 3 existing quirks into a single
quirk covering B2502* to also cover the last model while at the same time
reducing the number of quirks.
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241005212819.354681-3-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The Asus ExpertBook B2402CBA / B2402FBA are the non flip / flip versions
of the 14" Asus ExpertBook B2 with 12th gen Intel processors.
It has been reported that the B2402FVA which is the 14" Asus ExpertBook
B2 flip with 13th gen Intel processors needs to skip the IRQ override too.
And looking at Asus website there also is a B2402CVA which is the non flip
model with 13th gen Intel processors.
Summarizing the following 4 models of the Asus ExpertBook B2 are known:
B2402CBA: 12th gen Intel CPU, non flip
B2402FBA: 12th gen Intel CPU, flip
B2402CVA: 13th gen Intel CPU, non flip
B2402FVA: 13th gen Intel CPU, flip
Fold the 2 existing quirks for the B2402CBA and B2402FBA into a single
quirk covering B2402* to also cover the 2 other models while at the same
time reducing the number of quirks.
Reported-by: Stefan Blum <stefan.blum@gmail.com>
Closes: https://lore.kernel.org/platform-driver-x86/a983e6d5-c7ab-4758-be9b-7dcfc1b44ed3@gmail.com/
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241005212819.354681-2-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since commit 3f8ca2e115e5 ("vhost/scsi: Extract common handling code
from control queue handler") a null pointer dereference bug can be
triggered when guest sends an SCSI AN request.
In vhost_scsi_ctl_handle_vq(), `vc.target` is assigned with
`&v_req.tmf.lun[1]` within a switch-case block and is then passed to
vhost_scsi_get_req() which extracts `vc->req` and `tpg`. However, for
a `VIRTIO_SCSI_T_AN_*` request, tpg is not required, so `vc.target` is
set to NULL in this branch. Later, in vhost_scsi_get_req(),
`vc->target` is dereferenced without being checked, leading to a null
pointer dereference bug. This bug can be triggered from guest.
When this bug occurs, the vhost_worker process is killed while holding
`vq->mutex` and the corresponding tpg will remain occupied
indefinitely.
Below is the KASAN report:
Oops: general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 1 PID: 840 Comm: poc Not tainted 6.10.0+ #1
Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS
1.16.3-debian-1.16.3-2 04/01/2014
RIP: 0010:vhost_scsi_get_req+0x165/0x3a0
Code: 00 fc ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 2b 02 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 65 30 4c 89 e2 48 c1 ea 03 <0f> b6
04 02 4c 89 e2 83 e2 07 38 d0 7f 08 84 c0 0f 85 be 01 00 00
RSP: 0018:ffff888017affb50 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffff88801b000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff888017affcb8
RBP: ffff888017affb80 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffff888017affc88 R14: ffff888017affd1c R15: ffff888017993000
FS: 000055556e076500(0000) GS:ffff88806b100000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000200027c0 CR3: 0000000010ed0004 CR4: 0000000000370ef0
Call Trace:
<TASK>
? show_regs+0x86/0xa0
? die_addr+0x4b/0xd0
? exc_general_protection+0x163/0x260
? asm_exc_general_protection+0x27/0x30
? vhost_scsi_get_req+0x165/0x3a0
vhost_scsi_ctl_handle_vq+0x2a4/0xca0
? __pfx_vhost_scsi_ctl_handle_vq+0x10/0x10
? __switch_to+0x721/0xeb0
? __schedule+0xda5/0x5710
? __kasan_check_write+0x14/0x30
? _raw_spin_lock+0x82/0xf0
vhost_scsi_ctl_handle_kick+0x52/0x90
vhost_run_work_list+0x134/0x1b0
vhost_task_fn+0x121/0x350
...
</TASK>
---[ end trace 0000000000000000 ]---
Let's add a check in vhost_scsi_get_req.
Fixes: 3f8ca2e115e5 ("vhost/scsi: Extract common handling code from control queue handler")
Signed-off-by: Haoran Zhang <wh1sper@zju.edu.cn>
[whitespace fixes]
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <b26d7ddd-b098-4361-88f8-17ca7f90adf7@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This driver requires REGMAP_I2C to be selected in order to get access to
regmap_config, regmap_bus, and devm_regmap_init_i2c.
Add the missing dependency.
Fixes: 021730acbca6 ("hwmon: (max1668) Convert to use regmap")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20241002-hwmon-select-regmap-v1-4-548d03268934@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver requires REGMAP_I2C to be selected in order to get access to
regmap_config and devm_regmap_init_i2c. Add the missing dependency.
Fixes: 2b9ea4262ae9 ("hwmon: Add driver for ltc2991")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20241002-hwmon-select-regmap-v1-3-548d03268934@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver requires REGMAP_I2C to be selected in order to get access to
regmap_config and devm_regmap_init_i2c. Add the missing dependency.
Fixes: ef67959c4253 ("hwmon: (adt7470) Convert to use regmap")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20241002-hwmon-select-regmap-v1-2-548d03268934@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver requires REGMAP_I2C to be selected in order to get access to
regmap_config and devm_regmap_init_i2c. Add the missing dependency.
Fixes: df885d912f67 ("hwmon: (adm9240) Convert to regmap")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20241002-hwmon-select-regmap-v1-1-548d03268934@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver requires REGMAP_I2C to be selected in order to get access to
regmap_config and devm_regmap_init_i2c. Add the missing dependency.
Fixes: 07830d9ab34c ("hwmon: add initial NXP MC34VR500 PMIC monitoring support")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20241002-mc34vr500-select-regmap_i2c-v1-1-a01875d0a2e5@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
0-day reports:
drivers/hwmon/tmp513.c:162:21: error:
variable 'tmp51x_regmap_config' has initializer but incomplete type
162 | static const struct regmap_config tmp51x_regmap_config = {
| ^
struct regmap_config is only available if REGMAP is enabled.
Add the missing Kconfig dependency to fix the problem.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410020246.2cTDDx0X-lkp@intel.com/
Fixes: 59dfa75e5d82 ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.")
Cc: Eric Tremblay <etremblay@distech-controls.com>
Reviewed-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The device_for_each_child_node() loop requires calls to
fwnode_handle_put() upon early returns to decrement the refcount of
the child node and avoid leaking memory.
There are multiple early returns within that loop in
adt7475_fan_pwm_config(), but fwnode_handle_put() is never called.
Instead of adding the missing calls, the scoped version of the loop can
be used to simplify the code and avoid mistakes in the future if new
early returns are added.
This issue was recently introduced and it does not affect old kernels
that do not support the scoped variant.
Fixes: 777c97ff08d0 ("hwmon: (adt7475) Add support for configuring initial PWM state")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20240926-hwmon_adt7475_memleak-v1-1-89b8ee07507a@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Consistently use CVL instead of Columbiaville, since CVL is already
being used in all other sensor labels for the Intel N6000 card.
Fixes: e1983220ae14 ("hwmon: intel-m10-bmc-hwmon: Add N6000 sensors")
Signed-off-by: Peter Colberg <peter.colberg@intel.com>
Reviewed-by: Michael Adler <michael.adler@intel.com>
Message-ID: <20240919173417.867640-1-peter.colberg@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
