summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2025-02-15drm/msm/dpu: Disable dither in phys encoder cleanupJessica Zhang1-0/+3
Disable pingpong dither in dpu_encoder_helper_phys_cleanup(). This avoids the issue where an encoder unknowingly uses dither after reserving a pingpong block that was previously bound to an encoder that had enabled dither. Cc: stable@vger.kernel.org Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Closes: https://lore.kernel.org/all/jr7zbj5w7iq4apg3gofuvcwf4r2swzqjk7sshwcdjll4mn6ctt@l2n3qfpujg3q/ Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Fixes: 3c128638a07d ("drm/msm/dpu: add support for dither block in display") Patchwork: https://patchwork.freedesktop.org/patch/636517/ Link: https://lore.kernel.org/r/20250211-dither-disable-v1-1-ac2cb455f6b9@quicinc.com Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
2025-02-15drm/msm/dpu: Fix uninitialized variableEthan Carter Edwards1-4/+3
There is a possibility for an uninitialized *ret* variable to be returned in some code paths. Fix this by initializing *ret* to 0. Addresses-Coverity-ID: 1642546 ("Uninitialized scalar variable") Fixes: 774bcfb73176 ("drm/msm/dpu: add support for virtual planes") Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Patchwork: https://patchwork.freedesktop.org/patch/636201/ Link: https://lore.kernel.org/r/20250209-dpu-v2-1-114dfd4ebefd@ethancedwards.com Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
2025-02-15drm/msm/dp: account for widebus and yuv420 during mode validationAbhinav Kumar2-6/+10
Widebus allows the DP controller to operate in 2 pixel per clock mode. The mode validation logic validates the mode->clock against the max DP pixel clock. However the max DP pixel clock limit assumes widebus is already enabled. Adjust the mode validation logic to only compare the adjusted pixel clock which accounts for widebus against the max DP pixel clock. Also fix the mode validation logic for YUV420 modes as in that case as well, only half the pixel clock is needed. Cc: stable@vger.kernel.org Fixes: 757a2f36ab09 ("drm/msm/dp: enable widebus feature for display port") Fixes: 6db6e5606576 ("drm/msm/dp: change clock related programming for YUV420 over DP") Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Tested-by: Dale Whinham <daleyo@gmail.com> Patchwork: https://patchwork.freedesktop.org/patch/635789/ Link: https://lore.kernel.org/r/20250206-dp-widebus-fix-v2-1-cb89a0313286@quicinc.com Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
2025-02-15drm/msm/dpu: correct LM pairing for SM6150Dmitry Baryshkov1-2/+0
The SM6150 platform doesn't have 3DMux (MERGE_3D) block, so it can not split the screen between two LMs. Drop lm_pair fields as they don't make sense for this platform. Suggested-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Fixes: cb2f9144693b ("drm/msm/dpu: Add SM6150 support") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Patchwork: https://patchwork.freedesktop.org/patch/629377/ Link: https://lore.kernel.org/r/20241217-dpu-fix-sm6150-v2-1-9acc8f5addf3@linaro.org Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
2025-02-15drm/msm/dpu: enable DPU_WB_INPUT_CTRL for DPU 5.xDmitry Baryshkov3-3/+3
Several DPU 5.x platforms are supposed to be using DPU_WB_INPUT_CTRL, to bind WB and PINGPONG blocks, but they do not. Change those platforms to use WB_SM8250_MASK, which includes that bit. Fixes: 1f5bcc4316b3 ("drm/msm/dpu: enable writeback on SC8108X") Fixes: ab2b03d73a66 ("drm/msm/dpu: enable writeback on SM6125") Fixes: 47cebb740a83 ("drm/msm/dpu: enable writeback on SM8150") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Patchwork: https://patchwork.freedesktop.org/patch/628876/ Link: https://lore.kernel.org/r/20241214-dpu-drop-features-v1-2-988f0662cb7e@linaro.org Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
2025-02-15drm/msm/dpu: skip watchdog timer programming through TOP on >= SM8450Dmitry Baryshkov1-1/+1
The SM8450 and later chips have DPU_MDP_PERIPH_0_REMOVED feature bit set, which means that those platforms have dropped some of the registers, including the WD TIMER-related ones. Stop providing the callback to program WD timer on those platforms. Fixes: 100d7ef6995d ("drm/msm/dpu: add support for SM8450") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Patchwork: https://patchwork.freedesktop.org/patch/628874/ Link: https://lore.kernel.org/r/20241214-dpu-drop-features-v1-1-988f0662cb7e@linaro.org Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
2025-02-15Merge tag 's390-6.14-4' of ↵Linus Torvalds1-1/+2
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Vasily Gorbik: - Fix isolated VFs handling by verifying that a VF’s parent PF is locally owned before registering it in an existing PCI domain - Disable arch_test_bit() optimization for PROFILE_ALL_BRANCHES to workaround gcc failure in handling __builtin_constant_p() in this case - Fix CHPID "configure" attribute caching in CIO by not updating the cache when SCLP returns no data, ensuring consistent sysfs output - Remove CONFIG_LSM from default configs and rely on defaults, which enables BPF LSM hook * tag 's390-6.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/pci: Fix handling of isolated VFs s390/pci: Pull search for parent PF out of zpci_iov_setup_virtfn() s390/bitops: Disable arch_test_bit() optimization for PROFILE_ALL_BRANCHES s390/cio: Fix CHPID "configure" attribute caching s390/configs: Remove CONFIG_LSM
2025-02-15tegra210-adma: fix 32-bit x86 buildLinus Torvalds1-3/+14
The Tegra210 Audio DMA controller driver did a plain divide: page_no = (res_page->start - res_base->start) / cdata->ch_base_offset; which causes problems on 32-bit x86 configurations that have 64-bit resource sizes: x86_64-linux-ld: drivers/dma/tegra210-adma.o: in function `tegra_adma_probe': tegra210-adma.c:(.text+0x1322): undefined reference to `__udivdi3' because gcc doesn't generate the trivial code for a 64-by-32 divide, turning it into a function call to do a full 64-by-64 divide. And the kernel intentionally doesn't provide that helper function, because 99% of the time all you want is the narrower version. Of course, tegra210 is a 64-bit architecture and the 32-bit x86 build is purely for build testing, so this really is just about build coverage failure. But build coverage is good. Side note: div_u64() would be suboptimal if you actually have a 32-bit resource_t, so our "helper" for divides are admittedly making it harder than it should be to generate good code for all the possible cases. At some point, I'll consider 32-bit x86 so entirely legacy that I can't find it in myself to care any more, and we'll just add the __udivdi3 library function. But for now, the right thing to do is to use "div_u64()" to show that you know that you are doing the simpler divide with a 32-bit number. And the build error enforces that. While fixing the build issue, also check for division-by-zero, and for overflow. Which hopefully cannot happen on real production hardware, but the value of 'ch_base_offset' can definitely be zero in other places. Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2025-02-15drm/msm: Avoid rounding up to one jiffyRob Clark1-7/+4
If userspace is trying to achieve a timeout of zero, let 'em have it. Only round up if the timeout is greater than zero. Fixes: 4969bccd5f4e ("drm/msm: Avoid rounding down to zero jiffies") Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com> Patchwork: https://patchwork.freedesktop.org/patch/632264/
2025-02-15drm/msm/a6xx: Only print the GMU firmware version onceKonrad Dybcio1-4/+4
We only fetch it once from userland, so let's also only notify the user once and not on every runtime resume. As you can notice by the tags chain, more than one user found this annoying. Reported-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz> Suggested-by: Abel Vesa <abel.vesa@linaro.org> Suggested-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Patchwork: https://patchwork.freedesktop.org/patch/637062/ Signed-off-by: Rob Clark <robdclark@chromium.org>
2025-02-15Merge tag 'gpio-fixes-for-v6.14-rc3-take2' of ↵Linus Torvalds4-19/+87
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux Pull gpio fixes from Bartosz Golaszewski: - fix interrupt handling issues in gpio-bcm-kona - add an ACPI quirk for Acer Nitro ANV14 fixing an issue with spurious wake up events - add missing return value checks to gpio-stmpe - fix a crash in error path in gpiochip_get_ngpios() * tag 'gpio-fixes-for-v6.14-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: gpiolib: Fix crash on error in gpiochip_get_ngpios() gpio: stmpe: Check return value of stmpe_reg_read in stmpe_gpio_irq_sync_unlock gpiolib: acpi: Add a quirk for Acer Nitro ANV14 gpio: bcm-kona: Add missing newline to dev_err format string gpio: bcm-kona: Make sure GPIO bits are unlocked when requesting IRQ gpio: bcm-kona: Fix GPIO lock/unlock for banks above bank 0
2025-02-15geneve: Fix use-after-free in geneve_find_dev().Kuniyuki Iwashima1-8/+3
syzkaller reported a use-after-free in geneve_find_dev() [0] without repro. geneve_configure() links struct geneve_dev.next to net_generic(net, geneve_net_id)->geneve_list. The net here could differ from dev_net(dev) if IFLA_NET_NS_PID, IFLA_NET_NS_FD, or IFLA_TARGET_NETNSID is set. When dev_net(dev) is dismantled, geneve_exit_batch_rtnl() finally calls unregister_netdevice_queue() for each dev in the netns, and later the dev is freed. However, its geneve_dev.next is still linked to the backend UDP socket netns. Then, use-after-free will occur when another geneve dev is created in the netns. Let's call geneve_dellink() instead in geneve_destroy_tunnels(). [0]: BUG: KASAN: slab-use-after-free in geneve_find_dev drivers/net/geneve.c:1295 [inline] BUG: KASAN: slab-use-after-free in geneve_configure+0x234/0x858 drivers/net/geneve.c:1343 Read of size 2 at addr ffff000054d6ee24 by task syz.1.4029/13441 CPU: 1 UID: 0 PID: 13441 Comm: syz.1.4029 Not tainted 6.13.0-g0ad9617c78ac #24 dc35ca22c79fb82e8e7bc5c9c9adafea898b1e3d Hardware name: linux,dummy-virt (DT) Call trace: show_stack+0x38/0x50 arch/arm64/kernel/stacktrace.c:466 (C) __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0xbc/0x108 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0x16c/0x6f0 mm/kasan/report.c:489 kasan_report+0xc0/0x120 mm/kasan/report.c:602 __asan_report_load2_noabort+0x20/0x30 mm/kasan/report_generic.c:379 geneve_find_dev drivers/net/geneve.c:1295 [inline] geneve_configure+0x234/0x858 drivers/net/geneve.c:1343 geneve_newlink+0xb8/0x128 drivers/net/geneve.c:1634 rtnl_newlink_create+0x23c/0x868 net/core/rtnetlink.c:3795 __rtnl_newlink net/core/rtnetlink.c:3906 [inline] rtnl_newlink+0x1054/0x1630 net/core/rtnetlink.c:4021 rtnetlink_rcv_msg+0x61c/0x918 net/core/rtnetlink.c:6911 netlink_rcv_skb+0x1dc/0x398 net/netlink/af_netlink.c:2543 rtnetlink_rcv+0x34/0x50 net/core/rtnetlink.c:6938 netlink_unicast_kernel net/netlink/af_netlink.c:1322 [inline] netlink_unicast+0x618/0x838 net/netlink/af_netlink.c:1348 netlink_sendmsg+0x5fc/0x8b0 net/netlink/af_netlink.c:1892 sock_sendmsg_nosec net/socket.c:713 [inline] __sock_sendmsg net/socket.c:728 [inline] ____sys_sendmsg+0x410/0x6f8 net/socket.c:2568 ___sys_sendmsg+0x178/0x1d8 net/socket.c:2622 __sys_sendmsg net/socket.c:2654 [inline] __do_sys_sendmsg net/socket.c:2659 [inline] __se_sys_sendmsg net/socket.c:2657 [inline] __arm64_sys_sendmsg+0x12c/0x1c8 net/socket.c:2657 __invoke_syscall arch/arm64/kernel/syscall.c:35 [inline] invoke_syscall+0x90/0x278 arch/arm64/kernel/syscall.c:49 el0_svc_common+0x13c/0x250 arch/arm64/kernel/syscall.c:132 do_el0_svc+0x54/0x70 arch/arm64/kernel/syscall.c:151 el0_svc+0x4c/0xa8 arch/arm64/kernel/entry-common.c:744 el0t_64_sync_handler+0x78/0x108 arch/arm64/kernel/entry-common.c:762 el0t_64_sync+0x198/0x1a0 arch/arm64/kernel/entry.S:600 Allocated by task 13247: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x30/0x68 mm/kasan/common.c:68 kasan_save_alloc_info+0x44/0x58 mm/kasan/generic.c:568 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0x84/0xa0 mm/kasan/common.c:394 kasan_kmalloc include/linux/kasan.h:260 [inline] __do_kmalloc_node mm/slub.c:4298 [inline] __kmalloc_node_noprof+0x2a0/0x560 mm/slub.c:4304 __kvmalloc_node_noprof+0x9c/0x230 mm/util.c:645 alloc_netdev_mqs+0xb8/0x11a0 net/core/dev.c:11470 rtnl_create_link+0x2b8/0xb50 net/core/rtnetlink.c:3604 rtnl_newlink_create+0x19c/0x868 net/core/rtnetlink.c:3780 __rtnl_newlink net/core/rtnetlink.c:3906 [inline] rtnl_newlink+0x1054/0x1630 net/core/rtnetlink.c:4021 rtnetlink_rcv_msg+0x61c/0x918 net/core/rtnetlink.c:6911 netlink_rcv_skb+0x1dc/0x398 net/netlink/af_netlink.c:2543 rtnetlink_rcv+0x34/0x50 net/core/rtnetlink.c:6938 netlink_unicast_kernel net/netlink/af_netlink.c:1322 [inline] netlink_unicast+0x618/0x838 net/netlink/af_netlink.c:1348 netlink_sendmsg+0x5fc/0x8b0 net/netlink/af_netlink.c:1892 sock_sendmsg_nosec net/socket.c:713 [inline] __sock_sendmsg net/socket.c:728 [inline] ____sys_sendmsg+0x410/0x6f8 net/socket.c:2568 ___sys_sendmsg+0x178/0x1d8 net/socket.c:2622 __sys_sendmsg net/socket.c:2654 [inline] __do_sys_sendmsg net/socket.c:2659 [inline] __se_sys_sendmsg net/socket.c:2657 [inline] __arm64_sys_sendmsg+0x12c/0x1c8 net/socket.c:2657 __invoke_syscall arch/arm64/kernel/syscall.c:35 [inline] invoke_syscall+0x90/0x278 arch/arm64/kernel/syscall.c:49 el0_svc_common+0x13c/0x250 arch/arm64/kernel/syscall.c:132 do_el0_svc+0x54/0x70 arch/arm64/kernel/syscall.c:151 el0_svc+0x4c/0xa8 arch/arm64/kernel/entry-common.c:744 el0t_64_sync_handler+0x78/0x108 arch/arm64/kernel/entry-common.c:762 el0t_64_sync+0x198/0x1a0 arch/arm64/kernel/entry.S:600 Freed by task 45: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x30/0x68 mm/kasan/common.c:68 kasan_save_free_info+0x58/0x70 mm/kasan/generic.c:582 poison_slab_object mm/kasan/common.c:247 [inline] __kasan_slab_free+0x48/0x68 mm/kasan/common.c:264 kasan_slab_free include/linux/kasan.h:233 [inline] slab_free_hook mm/slub.c:2353 [inline] slab_free mm/slub.c:4613 [inline] kfree+0x140/0x420 mm/slub.c:4761 kvfree+0x4c/0x68 mm/util.c:688 netdev_release+0x94/0xc8 net/core/net-sysfs.c:2065 device_release+0x98/0x1c0 kobject_cleanup lib/kobject.c:689 [inline] kobject_release lib/kobject.c:720 [inline] kref_put include/linux/kref.h:65 [inline] kobject_put+0x2b0/0x438 lib/kobject.c:737 netdev_run_todo+0xe5c/0xfc8 net/core/dev.c:11185 rtnl_unlock+0x20/0x38 net/core/rtnetlink.c:151 cleanup_net+0x4fc/0x8c0 net/core/net_namespace.c:648 process_one_work+0x700/0x1398 kernel/workqueue.c:3236 process_scheduled_works kernel/workqueue.c:3317 [inline] worker_thread+0x8c4/0xe10 kernel/workqueue.c:3398 kthread+0x4bc/0x608 kernel/kthread.c:464 ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:862 The buggy address belongs to the object at ffff000054d6e000 which belongs to the cache kmalloc-cg-4k of size 4096 The buggy address is located 3620 bytes inside of freed 4096-byte region [ffff000054d6e000, ffff000054d6f000) The buggy address belongs to the physical page: page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x94d68 head: order:3 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0 memcg:ffff000016276181 flags: 0x3fffe0000000040(head|node=0|zone=0|lastcpupid=0x1ffff) page_type: f5(slab) raw: 03fffe0000000040 ffff0000c000f500 dead000000000122 0000000000000000 raw: 0000000000000000 0000000000040004 00000001f5000000 ffff000016276181 head: 03fffe0000000040 ffff0000c000f500 dead000000000122 0000000000000000 head: 0000000000000000 0000000000040004 00000001f5000000 ffff000016276181 head: 03fffe0000000003 fffffdffc1535a01 ffffffffffffffff 0000000000000000 head: 0000000000000008 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff000054d6ed00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff000054d6ed80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff000054d6ee00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff000054d6ee80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff000054d6ef00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Fixes: 2d07dc79fe04 ("geneve: add initial netdev driver for GENEVE tunnels") Reported-by: syzkaller <syzkaller@googlegroups.com> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://patch.msgid.link/20250213043354.91368-1-kuniyu@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-15Merge tag 'pci-v6.14-fixes-3' of ↵Linus Torvalds2-3/+5
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci Pull pci fixes from Bjorn Helgaas: - Update a BUILD_BUG_ON() usage that works on current compilers, but breaks compilation on gcc 5.3.1 (Alex Williamson) - Avoid use of FLR for Mediatek MT7922 WiFi; the device previously worked after a long timeout and fallback to SBR, but after a recent RRS change it doesn't work at all after FLR (Bjorn Helgaas) * tag 'pci-v6.14-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: PCI: Avoid FLR for Mediatek MT7922 WiFi PCI: Fix BUILD_BUG_ON usage for old gcc
2025-02-15Merge tag 'kvm-x86-fixes-6.14-rcN' of https://github.com/kvm-x86/linux into HEADPaolo Bonzini96-479/+703
KVM fixes for 6.14 part 1 - Reject Hyper-V SEND_IPI hypercalls if the local APIC isn't being emulated by KVM to fix a NULL pointer dereference. - Enter guest mode (L2) from KVM's perspective before initializing the vCPU's nested NPT MMU so that the MMU is properly tagged for L2, not L1. - Load the guest's DR6 outside of the innermost .vcpu_run() loop, as the guest's value may be stale if a VM-Exit is handled in the fastpath.
2025-02-15x86/sev: Fix broken SNP support with KVM module built-inAshish Kalra1-4/+30
Fix issues with enabling SNP host support and effectively SNP support which is broken with respect to the KVM module being built-in. SNP host support is enabled in snp_rmptable_init() which is invoked as device_initcall(). SNP check on IOMMU is done during IOMMU PCI init (IOMMU_PCI_INIT stage). And for that reason snp_rmptable_init() is currently invoked via device_initcall() and cannot be invoked via subsys_initcall() as core IOMMU subsystem gets initialized via subsys_initcall(). Now, if kvm_amd module is built-in, it gets initialized before SNP host support is enabled in snp_rmptable_init() : [ 10.131811] kvm_amd: TSC scaling supported [ 10.136384] kvm_amd: Nested Virtualization enabled [ 10.141734] kvm_amd: Nested Paging enabled [ 10.146304] kvm_amd: LBR virtualization supported [ 10.151557] kvm_amd: SEV enabled (ASIDs 100 - 509) [ 10.156905] kvm_amd: SEV-ES enabled (ASIDs 1 - 99) [ 10.162256] kvm_amd: SEV-SNP enabled (ASIDs 1 - 99) [ 10.171508] kvm_amd: Virtual VMLOAD VMSAVE supported [ 10.177052] kvm_amd: Virtual GIF supported ... ... [ 10.201648] kvm_amd: in svm_enable_virtualization_cpu And then svm_x86_ops->enable_virtualization_cpu() (svm_enable_virtualization_cpu) programs MSR_VM_HSAVE_PA as following: wrmsrl(MSR_VM_HSAVE_PA, sd->save_area_pa); So VM_HSAVE_PA is non-zero before SNP support is enabled on all CPUs. snp_rmptable_init() gets invoked after svm_enable_virtualization_cpu() as following : ... [ 11.256138] kvm_amd: in svm_enable_virtualization_cpu ... [ 11.264918] SEV-SNP: in snp_rmptable_init This triggers a #GP exception in snp_rmptable_init() when snp_enable() is invoked to set SNP_EN in SYSCFG MSR: [ 11.294289] unchecked MSR access error: WRMSR to 0xc0010010 (tried to write 0x0000000003fc0000) at rIP: 0xffffffffaf5d5c28 (native_write_msr+0x8/0x30) ... [ 11.294404] Call Trace: [ 11.294482] <IRQ> [ 11.294513] ? show_stack_regs+0x26/0x30 [ 11.294522] ? ex_handler_msr+0x10f/0x180 [ 11.294529] ? search_extable+0x2b/0x40 [ 11.294538] ? fixup_exception+0x2dd/0x340 [ 11.294542] ? exc_general_protection+0x14f/0x440 [ 11.294550] ? asm_exc_general_protection+0x2b/0x30 [ 11.294557] ? __pfx_snp_enable+0x10/0x10 [ 11.294567] ? native_write_msr+0x8/0x30 [ 11.294570] ? __snp_enable+0x5d/0x70 [ 11.294575] snp_enable+0x19/0x20 [ 11.294578] __flush_smp_call_function_queue+0x9c/0x3a0 [ 11.294586] generic_smp_call_function_single_interrupt+0x17/0x20 [ 11.294589] __sysvec_call_function+0x20/0x90 [ 11.294596] sysvec_call_function+0x80/0xb0 [ 11.294601] </IRQ> [ 11.294603] <TASK> [ 11.294605] asm_sysvec_call_function+0x1f/0x30 ... [ 11.294631] arch_cpu_idle+0xd/0x20 [ 11.294633] default_idle_call+0x34/0xd0 [ 11.294636] do_idle+0x1f1/0x230 [ 11.294643] ? complete+0x71/0x80 [ 11.294649] cpu_startup_entry+0x30/0x40 [ 11.294652] start_secondary+0x12d/0x160 [ 11.294655] common_startup_64+0x13e/0x141 [ 11.294662] </TASK> This #GP exception is getting triggered due to the following errata for AMD family 19h Models 10h-1Fh Processors: Processor may generate spurious #GP(0) Exception on WRMSR instruction: Description: The Processor will generate a spurious #GP(0) Exception on a WRMSR instruction if the following conditions are all met: - the target of the WRMSR is a SYSCFG register. - the write changes the value of SYSCFG.SNPEn from 0 to 1. - One of the threads that share the physical core has a non-zero value in the VM_HSAVE_PA MSR. The document being referred to above: https://www.amd.com/content/dam/amd/en/documents/processor-tech-docs/revision-guides/57095-PUB_1_01.pdf To summarize, with kvm_amd module being built-in, KVM/SVM initialization happens before host SNP is enabled and this SVM initialization sets VM_HSAVE_PA to non-zero, which then triggers a #GP when SYSCFG.SNPEn is being set and this will subsequently cause SNP_INIT(_EX) to fail with INVALID_CONFIG error as SYSCFG[SnpEn] is not set on all CPUs. Essentially SNP host enabling code should be invoked before KVM initialization, which is currently not the case when KVM is built-in. Add fix to call snp_rmptable_init() early from iommu_snp_enable() directly and not invoked via device_initcall() which enables SNP host support before KVM initialization with kvm_amd module built-in. Add additional handling for `iommu=off` or `amd_iommu=off` options. Note that IOMMUs need to be enabled for SNP initialization, therefore, if host SNP support is enabled but late IOMMU initialization fails then that will cause PSP driver's SNP_INIT to fail as IOMMU SNP sanity checks in SNP firmware will fail with invalid configuration error as below: [ 9.723114] ccp 0000:23:00.1: sev enabled [ 9.727602] ccp 0000:23:00.1: psp enabled [ 9.732527] ccp 0000:a2:00.1: enabling device (0000 -> 0002) [ 9.739098] ccp 0000:a2:00.1: no command queues available [ 9.745167] ccp 0000:a2:00.1: psp enabled [ 9.805337] ccp 0000:23:00.1: SEV-SNP: failed to INIT rc -5, error 0x3 [ 9.866426] ccp 0000:23:00.1: SEV API:1.53 build:5 Fixes: c3b86e61b756 ("x86/cpufeatures: Enable/unmask SEV-SNP CPU feature") Co-developed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Sean Christopherson <seanjc@google.com> Co-developed-by: Vasant Hegde <vasant.hegde@amd.com> Signed-off-by: Vasant Hegde <vasant.hegde@amd.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Ashish Kalra <ashish.kalra@amd.com> Acked-by: Joerg Roedel <jroedel@suse.de> Message-ID: <138b520fb83964782303b43ade4369cd181fdd9c.1739226950.git.ashish.kalra@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2025-02-15crypto: ccp: Add external API interface for PSP module initializationSean Christopherson1-0/+14
KVM is dependent on the PSP SEV driver and PSP SEV driver needs to be loaded before KVM module. In case of module loading any dependent modules are automatically loaded but in case of built-in modules there is no inherent mechanism available to specify dependencies between modules and ensure that any dependent modules are loaded implicitly. Add a new external API interface for PSP module initialization which allows PSP SEV driver to be loaded explicitly if KVM is built-in. Signed-off-by: Sean Christopherson <seanjc@google.com> Co-developed-by: Ashish Kalra <ashish.kalra@amd.com> Signed-off-by: Ashish Kalra <ashish.kalra@amd.com> Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Message-ID: <15279ca0cad56a07cf12834ec544310f85ff5edc.1739226950.git.ashish.kalra@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2025-02-15Merge tag 'thermal-6.14-rc3' of ↵Linus Torvalds1-2/+0
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull thermal control fixes from Rafael Wysocki: "Fix a regression caused by an inadvertent change of the THERMAL_GENL_ATTR_CPU_CAPABILITY value in one of the recent thermal commits (Zhang Rui) and drop a stale piece of documentation (Daniel Lezcano)" * tag 'thermal-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: thermal/cpufreq_cooling: Remove structure member documentation thermal/netlink: Prevent userspace segmentation fault by adjusting UAPI header
2025-02-15Merge tag 'mmc-v6.14-rc1' of ↵Linus Torvalds2-41/+20
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc Pull MMC host fixes from Ulf Hansson: - mtk-sd: Fix register settings for hs400(es) mode - sdhci_am654: Revert patch for start-signal-voltage-switch * tag 'mmc-v6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: mmc: mtk-sd: Fix register settings for hs400(es) mode Revert "mmc: sdhci_am654: Add sdhci_am654_start_signal_voltage_switch"
2025-02-15Merge tag 'efi-fixes-for-v6.14-1' of ↵Linus Torvalds3-2/+10
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi Pull EFI fixes from Ard Biesheuvel: "Take the newly introduced EFI_MEMORY_HOT_PLUGGABLE memory attribute into account when placing the kernel image in memory at boot. Otherwise, the presence of the kernel image could prevent such a memory region from being unplugged at runtime if it was 'cold plugged', i.e., already plugged in at boot time (and exposed via the EFI memory map). This should ensure that the new EFI_MEMORY_HOT_PLUGGABLE memory attribute is used consistently by Linux before it ever turns up in production, ensuring that we can make meaningful use of it without running the risk of regressing existing users" * tag 'efi-fixes-for-v6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi: efi: Use BIT_ULL() constants for memory attributes efi: Avoid cold plugged memory for placing the kernel
2025-02-15net: wwan: mhi_wwan_mbim: Silence sequence number glitch errorsStephan Gerhold1-1/+1
When using the Qualcomm X55 modem on the ThinkPad X13s, the kernel log is constantly being filled with errors related to a "sequence number glitch", e.g.: [ 1903.284538] sequence number glitch prev=16 curr=0 [ 1913.812205] sequence number glitch prev=50 curr=0 [ 1923.698219] sequence number glitch prev=142 curr=0 [ 2029.248276] sequence number glitch prev=1555 curr=0 [ 2046.333059] sequence number glitch prev=70 curr=0 [ 2076.520067] sequence number glitch prev=272 curr=0 [ 2158.704202] sequence number glitch prev=2655 curr=0 [ 2218.530776] sequence number glitch prev=2349 curr=0 [ 2225.579092] sequence number glitch prev=6 curr=0 Internet connectivity is working fine, so this error seems harmless. It looks like modem does not preserve the sequence number when entering low power state; the amount of errors depends on how actively the modem is being used. A similar issue has also been seen on USB-based MBIM modems [1]. However, in cdc_ncm.c the "sequence number glitch" message is a debug message instead of an error. Apply the same to the mhi_wwan_mbim.c driver to silence these errors when using the modem. [1]: https://lists.freedesktop.org/archives/libmbim-devel/2016-November/000781.html Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://patch.msgid.link/20250212-mhi-wwan-mbim-sequence-glitch-v1-1-503735977cbd@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-14EDAC/qcom: Correct interrupt enable register configurationKomal Bajaj1-2/+2
The previous implementation incorrectly configured the cmn_interrupt_2_enable register for interrupt handling. Using cmn_interrupt_2_enable to configure Tag, Data RAM ECC interrupts would lead to issues like double handling of the interrupts (EL1 and EL3) as cmn_interrupt_2_enable is meant to be configured for interrupts which needs to be handled by EL3. EL1 LLCC EDAC driver needs to use cmn_interrupt_0_enable register to configure Tag, Data RAM ECC interrupts instead of cmn_interrupt_2_enable. Fixes: 27450653f1db ("drivers: edac: Add EDAC driver support for QCOM SoCs") Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: <stable@kernel.org> Link: https://lore.kernel.org/r/20241119064608.12326-1-quic_kbajaj@quicinc.com
2025-02-14Merge tag 'arm64-fixes' of ↵Linus Torvalds1-4/+8
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fixes from Will Deacon: - Fix kexec and hibernation when using 5-level page-table configuration - Remove references to non-existent SF8MM4 and SF8MM8 ID register fields, hooking up hwcaps for the FPRCVT, F8MM4 and F8MM8 fields instead - Drop unused .ARM.attributes ELF sections - Fix array indexing when probing CPU cache topology from firmware - Fix potential use-after-free in AMU initialisation code - Work around broken GTDT entries by tolerating excessively large timer arrays - Force use of Rust's "softfloat" target to avoid a threatening warning about the NEON target feature - Typo fix in GCS documentation and removal of duplicate Kconfig select * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: rust: clean Rust 1.85.0 warning using softfloat target arm64: Add missing registrations of hwcaps ACPI: GTDT: Relax sanity checking on Platform Timers array count arm64: amu: Delay allocating cpumask for AMU FIE support arm64: cacheinfo: Avoid out-of-bounds write to cacheinfo array arm64: Handle .ARM.attributes section in linker scripts arm64/hwcap: Remove stray references to SF8MMx arm64/gcs: Fix documentation for HWCAP arm64: Kconfig: Remove selecting replaced HAVE_FUNCTION_GRAPH_RETVAL arm64: Fix 5-level paging support in kexec/hibernate trampoline
2025-02-14Merge tag 'iommu-fixes-v6.14-rc2' of ↵Linus Torvalds6-5/+13
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux Pull iommu fixes from Joerg Roedel: - core: fix potential memory leak in iopf_queue_remove_device() - Intel VT-d: handle faults correctly in intel_iommu_drain_pasid_prq() - AMD-Vi: fix faults happening in resume path - typo and spelling fixes * tag 'iommu-fixes-v6.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: iommu/vt-d: Make intel_iommu_drain_pasid_prq() cover faults for RID iommu/exynos: Fix typos iommu: Fix a spelling error iommu/amd: Expicitly enable CNTRL.EPHEn bit in resume path iommu: Fix potential memory leak in iopf_queue_remove_device()
2025-02-14Merge tag 'for-linus-6.14-rc3-tag' of ↵Linus Torvalds1-9/+13
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fixes from Juergen Gross: "Three fixes to xen-swiotlb driver: - two fixes for issues coming up due to another fix in 6.12 - addition of an __init annotation" * tag 'for-linus-6.14-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: Xen/swiotlb: mark xen_swiotlb_fixup() __init x86/xen: allow larger contiguous memory regions in PV guests xen/swiotlb: relax alignment requirements
2025-02-14accel/amdxdna: Refactor hardware context destroy routineLizhi Hou3-13/+21
It is required by firmware to wait up to 2 seconds for pending commands before sending the destroy hardware context command. After 2 seconds wait, if there are still pending commands, driver needs to cancel them. So the context destroy steps need to be: 1. Stop drm scheduler. (drm_sched_entity_destroy) 2. Wait up to 2 seconds for pending commands. 3. Destroy hardware context and cancel the rest pending requests. 4. Wait all jobs associated with the hwctx are freed. 5. Free job resources. Signed-off-by: Lizhi Hou <lizhi.hou@amd.com> Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com> Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com> Link: https://patchwork.freedesktop.org/patch/msgid/20250124173536.148676-1-lizhi.hou@amd.com
2025-02-14nouveau/svm: fix missing folio unlock + put after make_device_exclusive_range()David Hildenbrand1-2/+7
In case we have to retry the loop, we are missing to unlock+put the folio. In that case, we will keep failing make_device_exclusive_range() because we cannot grab the folio lock, and even return from the function with the folio locked and referenced, effectively never succeeding the make_device_exclusive_range(). While at it, convert the other unlock+put to use a folio as well. This was found by code inspection. Fixes: 8f187163eb89 ("nouveau/svm: implement atomic SVM access") Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Alistair Popple <apopple@nvidia.com> Tested-by: Alistair Popple <apopple@nvidia.com> Signed-off-by: Danilo Krummrich <dakr@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20250124181524.3584236-2-david@redhat.com
2025-02-14tee: optee: Fix supplicant wait loopSumit Garg1-27/+8
OP-TEE supplicant is a user-space daemon and it's possible for it be hung or crashed or killed in the middle of processing an OP-TEE RPC call. It becomes more complicated when there is incorrect shutdown ordering of the supplicant process vs the OP-TEE client application which can eventually lead to system hang-up waiting for the closure of the client application. Allow the client process waiting in kernel for supplicant response to be killed rather than indefinitely waiting in an unkillable state. Also, a normal uninterruptible wait should not have resulted in the hung-task watchdog getting triggered, but the endless loop would. This fixes issues observed during system reboot/shutdown when supplicant got hung for some reason or gets crashed/killed which lead to client getting hung in an unkillable state. It in turn lead to system being in hung up state requiring hard power off/on to recover. Fixes: 4fb0a5eb364d ("tee: add OP-TEE driver") Suggested-by: Arnd Bergmann <arnd@arndb.de> Cc: stable@vger.kernel.org Signed-off-by: Sumit Garg <sumit.garg@linaro.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-02-14platform: cznic: CZNIC_PLATFORMS should depend on ARCH_MVEBUGeert Uytterhoeven1-0/+1
CZ.NIC's Turris devices are based on Marvell EBU SoCs. Hence add a dependency on ARCH_MVEBU, to prevent asking the user about these drivers when configuring a kernel that cannot run on an affected CZ.NIC Turris system. Fixes: 992f1a3d4e88498d ("platform: cznic: Add preliminary support for Turris Omnia MCU") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-02-14firmware: imx: IMX_SCMI_MISC_DRV should depend on ARCH_MXCGeert Uytterhoeven1-0/+1
The i.MX System Controller Management Interface firmware is only present on Freescale i.MX SoCs. Hence add a dependency on ARCH_MXC, to prevent asking the user about this driver when configuring a kernel without Freescale i.MX platform support. Fixes: 514b2262ade48a05 ("firmware: arm_scmi: Fix i.MX build dependency") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-02-14serial: 8250: Fix fifo underflow on flushJohn Keeping3-0/+27
When flushing the serial port's buffer, uart_flush_buffer() calls kfifo_reset() but if there is an outstanding DMA transfer then the completion function will consume data from the kfifo via uart_xmit_advance(), underflowing and leading to ongoing DMA as the driver tries to transmit another 2^32 bytes. This is readily reproduced with serial-generic and amidi sending even short messages as closing the device on exit will wait for the fifo to drain and in the underflow case amidi hangs for 30 seconds on exit in tty_wait_until_sent(). A trace of that gives: kworker/1:1-84 [001] 51.769423: bprint: serial8250_tx_dma: tx_size=3 fifo_len=3 amidi-763 [001] 51.769460: bprint: uart_flush_buffer: resetting fifo irq/21-fe530000-76 [000] 51.769474: bprint: __dma_tx_complete: tx_size=3 irq/21-fe530000-76 [000] 51.769479: bprint: serial8250_tx_dma: tx_size=4096 fifo_len=4294967293 irq/21-fe530000-76 [000] 51.781295: bprint: __dma_tx_complete: tx_size=4096 irq/21-fe530000-76 [000] 51.781301: bprint: serial8250_tx_dma: tx_size=4096 fifo_len=4294963197 irq/21-fe530000-76 [000] 51.793131: bprint: __dma_tx_complete: tx_size=4096 irq/21-fe530000-76 [000] 51.793135: bprint: serial8250_tx_dma: tx_size=4096 fifo_len=4294959101 irq/21-fe530000-76 [000] 51.804949: bprint: __dma_tx_complete: tx_size=4096 Since the port lock is held in when the kfifo is reset in uart_flush_buffer() and in __dma_tx_complete(), adding a flush_buffer hook to adjust the outstanding DMA byte count is sufficient to avoid the kfifo underflow. Fixes: 9ee4b83e51f74 ("serial: 8250: Add support for dmaengine") Cc: stable <stable@kernel.org> Signed-off-by: John Keeping <jkeeping@inmusicbrands.com> Link: https://lore.kernel.org/r/20250208124148.1189191-1-jkeeping@inmusicbrands.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14usb: typec: tcpm: PSSourceOffTimer timeout in PR_Swap enters ERROR_RECOVERYJos Wang1-2/+1
As PD2.0 spec ("6.5.6.2 PSSourceOffTimer")，the PSSourceOffTimer is used by the Policy Engine in Dual-Role Power device that is currently acting as a Sink to timeout on a PS_RDY Message during a Power Role Swap sequence. This condition leads to a Hard Reset for USB Type-A and Type-B Plugs and Error Recovery for Type-C plugs and return to USB Default Operation. Therefore, after PSSourceOffTimer timeout, the tcpm state machine should switch from PR_SWAP_SNK_SRC_SINK_OFF to ERROR_RECOVERY. This can also solve the test items in the USB power delivery compliance test: TEST.PD.PROT.SNK.12 PR_Swap – PSSourceOffTimer Timeout [1] https://usb.org/document-library/usb-power-delivery-compliance-test-specification-0/USB_PD3_CTS_Q4_2025_OR.zip Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)") Cc: stable <stable@kernel.org> Signed-off-by: Jos Wang <joswang@lenovo.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by: Amit Sunil Dhamne <amitsd@google.com> Link: https://lore.kernel.org/r/20250213134921.3798-1-joswang1221@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14usb: roles: set switch registered flag early onElson Roy Serrao1-2/+3
The role switch registration and set_role() can happen in parallel as they are invoked independent of each other. There is a possibility that a driver might spend significant amount of time in usb_role_switch_register() API due to the presence of time intensive operations like component_add() which operate under common mutex. This leads to a time window after allocating the switch and before setting the registered flag where the set role notifications are dropped. Below timeline summarizes this behavior Thread1 | Thread2 usb_role_switch_register() | | | ---> allocate switch | | | ---> component_add() | usb_role_switch_set_role() | | | | | --> Drop role notifications | | since sw->registered | | flag is not set. | | --->Set registered flag.| To avoid this, set the registered flag early on in the switch register API. Fixes: b787a3e78175 ("usb: roles: don't get/set_role() when usb_role_switch is unregistered") Cc: stable <stable@kernel.org> Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20250206193950.22421-1-quic_eserrao@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14usb: gadget: uvc: Fix unstarted kthread workerFrederic Weisbecker1-1/+1
The behaviour of kthread_create_worker() was recently changed to align with the one of kthread_create(). The kthread worker is created but not awaken by default. This is to allow the use of kthread_affine_preferred() and kthread_bind[_mask]() with kthread workers. In order to keep the old behaviour and wake the kthread up, kthread_run_worker() must be used. All the pre-existing users have been converted, except for UVC that was introduced in the same merge window as the API change. This results in hangs: INFO: task UVCG:82 blocked for more than 491 seconds. Tainted: G T 6.13.0-rc2-00014-gb04e317b5226 #1 task:UVCG state:D stack:0 pid:82 Call Trace: __schedule schedule schedule_preempt_disabled kthread ? kthread_flush_work ret_from_fork ret_from_fork_asm entry_INT80_32 Fix this with converting UVCG kworker to the new API. Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202502121025.55bfa801-lkp@intel.com Fixes: f0bbfbd16b3b ("usb: gadget: uvc: rework to enqueue in pump worker from encoded queue") Cc: stable <stable@kernel.org> Cc: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20250212135514.30539-1-frederic@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14USB: quirks: add USB_QUIRK_NO_LPM quirk for Teclast distLei Huang1-0/+3
Teclast disk used on Huawei hisi platforms doesn't work well, losing connectivity intermittently if LPM is enabled. Add quirk disable LPM to resolve the issue. Signed-off-by: Lei Huang <huanglei@kylinos.cn> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20250212093829.7379-1-huanglei814@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14usb: gadget: core: flush gadget workqueue after device removalRoy Luo1-1/+1
device_del() can lead to new work being scheduled in gadget->work workqueue. This is observed, for example, with the dwc3 driver with the following call stack: device_del() gadget_unbind_driver() usb_gadget_disconnect_locked() dwc3_gadget_pullup() dwc3_gadget_soft_disconnect() usb_gadget_set_state() schedule_work(&gadget->work) Move flush_work() after device_del() to ensure the workqueue is cleaned up. Fixes: 5702f75375aa9 ("usb: gadget: udc-core: move sysfs_notify() to a workqueue") Cc: stable <stable@kernel.org> Signed-off-by: Roy Luo <royluo@google.com> Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20250204233642.666991-1-royluo@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14USB: gadget: f_midi: f_midi_complete to call queue_workJill Donahue1-1/+1
When using USB MIDI, a lock is attempted to be acquired twice through a re-entrant call to f_midi_transmit, causing a deadlock. Fix it by using queue_work() to schedule the inner f_midi_transmit() via a high priority work queue from the completion handler. Link: https://lore.kernel.org/all/CAArt=LjxU0fUZOj06X+5tkeGT+6RbXzpWg1h4t4Fwa_KGVAX6g@mail.gmail.com/ Fixes: d5daf49b58661 ("USB: gadget: midi: add midi function driver") Cc: stable <stable@kernel.org> Signed-off-by: Jill Donahue <jilliandonahue58@gmail.com> Link: https://lore.kernel.org/r/20250211174805.1369265-1-jdonahue@fender.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14usb: core: fix pipe creation for get_bMaxPacketSize0Stefan Eichenberger1-2/+1
When usb_control_msg is used in the get_bMaxPacketSize0 function, the USB pipe does not include the endpoint device number. This can cause failures when a usb hub port is reinitialized after encountering a bad cable connection. As a result, the system logs the following error messages: usb usb2-port1: cannot reset (err = -32) usb usb2-port1: Cannot enable. Maybe the USB cable is bad? usb usb2-port1: attempt power cycle usb 2-1: new high-speed USB device number 5 using ci_hdrc usb 2-1: device descriptor read/8, error -71 The problem began after commit 85d07c556216 ("USB: core: Unite old scheme and new scheme descriptor reads"). There usb_get_device_descriptor was replaced with get_bMaxPacketSize0. Unlike usb_get_device_descriptor, the get_bMaxPacketSize0 function uses the macro usb_rcvaddr0pipe, which does not include the endpoint device number. usb_get_device_descriptor, on the other hand, used the macro usb_rcvctrlpipe, which includes the endpoint device number. By modifying the get_bMaxPacketSize0 function to use usb_rcvctrlpipe instead of usb_rcvaddr0pipe, the issue can be resolved. This change will ensure that the endpoint device number is included in the USB pipe, preventing reinitialization failures. If the endpoint has not set the device number yet, it will still work because the device number is 0 in udev. Cc: stable <stable@kernel.org> Fixes: 85d07c556216 ("USB: core: Unite old scheme and new scheme descriptor reads") Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20250203105840.17539-1-eichest@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14usb: dwc3: Fix timeout issue during controller enter/exit from halt stateSelvarasu Ganesan1-0/+34
There is a frequent timeout during controller enter/exit from halt state after toggling the run_stop bit by SW. This timeout occurs when performing frequent role switches between host and device, causing device enumeration issues due to the timeout. This issue was not present when USB2 suspend PHY was disabled by passing the SNPS quirks (snps,dis_u2_susphy_quirk and snps,dis_enblslpm_quirk) from the DTS. However, there is a requirement to enable USB2 suspend PHY by setting of GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY bits when controller starts in gadget or host mode results in the timeout issue. This commit addresses this timeout issue by ensuring that the bits GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting the dwc3_gadget_run_stop sequence and restoring them after the dwc3_gadget_run_stop sequence is completed. Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Cc: stable <stable@kernel.org> Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20250201163903.459-1-selvarasu.g@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14USB: Add USB_QUIRK_NO_LPM quirk for sony xperia xz1 smartphoneMathias Nyman1-0/+3
The fastboot tool for communicating with Android bootloaders does not work reliably with this device if USB 2 Link Power Management (LPM) is enabled. Various fastboot commands are affected, including the following, which usually reproduces the problem within two tries: fastboot getvar kernel getvar:kernel FAILED (remote: 'GetVar Variable Not found') This issue was hidden on many systems up until commit 63a1f8454962 ("xhci: stored cached port capability values in one place") as the xhci driver failed to detect USB 2 LPM support if USB 3 ports were listed before USB 2 ports in the "supported protocol capabilities". Adding the quirk resolves the issue. No drawbacks are expected since the device uses different USB product IDs outside of fastboot mode, and since fastboot commands worked before, until LPM was enabled on the tested system by the aforementioned commit. Based on a patch from Forest <forestix@nom.one> from which most of the code and commit message is taken. Cc: stable <stable@kernel.org> Reported-by: Forest <forestix@nom.one> Closes: https://lore.kernel.org/hk8umj9lv4l4qguftdq1luqtdrpa1gks5l@sonic.net Tested-by: Forest <forestix@nom.one> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20250206151836.51742-1-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14USB: cdc-acm: Fill in Renesas R-Car D3 USB Download mode quirkMarek Vasut1-3/+6
Add Renesas R-Car D3 USB Download mode quirk and update comments on all the other Renesas R-Car USB Download mode quirks to discern them from each other. This follows R-Car Series, 3rd Generation reference manual Rev.2.00 chapter 19.2.8 USB download mode . Fixes: 6d853c9e4104 ("usb: cdc-acm: Add DISABLE_ECHO for Renesas USB Download mode") Cc: stable <stable@kernel.org> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20250209145708.106914-1-marek.vasut+renesas@mailbox.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14usb: cdc-acm: Fix handling of oversized fragmentsJann Horn1-1/+1
If we receive an initial fragment of size 8 bytes which specifies a wLength of 1 byte (so the reassembled message is supposed to be 9 bytes long), and we then receive a second fragment of size 9 bytes (which is not supposed to happen), we currently wrongly bypass the fragment reassembly code but still pass the pointer to the acm->notification_buffer to acm_process_notification(). Make this less wrong by always going through fragment reassembly when we expect more fragments. Before this patch, receiving an overlong fragment could lead to `newctrl` in acm_process_notification() being uninitialized data (instead of data coming from the device). Cc: stable <stable@kernel.org> Fixes: ea2583529cd1 ("cdc-acm: reassemble fragmented notifications") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14usb: cdc-acm: Check control transfer buffer size before accessJann Horn1-3/+14
If the first fragment is shorter than struct usb_cdc_notification, we can't calculate an expected_size. Log an error and discard the notification instead of reading lengths from memory outside the received data, which can lead to memory corruption when the expected_size decreases between fragments, causing `expected_size - acm->nb_index` to wrap. This issue has been present since the beginning of git history; however, it only leads to memory corruption since commit ea2583529cd1 ("cdc-acm: reassemble fragmented notifications"). A mitigating factor is that acm_ctrl_irq() can only execute after userspace has opened /dev/ttyACM*; but if ModemManager is running, ModemManager will do that automatically depending on the USB device's vendor/product IDs and its other interfaces. Cc: stable <stable@kernel.org> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14usb: xhci: Restore xhci_pci support for Renesas HCsMichal Pecio1-3/+4
Some Renesas HCs require firmware upload to work, this is handled by the xhci_pci_renesas driver. Other variants of those chips load firmware from a SPI flash and are ready to work with xhci_pci alone. A refactor merged in v6.12 broke the latter configuration so that users are finding their hardware ignored by the normal driver and are forced to enable the firmware loader which isn't really necessary on their systems. Let xhci_pci work with those chips as before when the firmware loader is disabled by kernel configuration. Fixes: 25f51b76f90f ("xhci-pci: Make xhci-pci-renesas a proper modular driver") Cc: stable <stable@kernel.org> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219616 Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219726 Signed-off-by: Michal Pecio <michal.pecio@gmail.com> Tested-by: Nicolai Buchwitz <nb@tipi-net.de> Link: https://lore.kernel.org/r/20250128104529.58a79bfc@foxbook Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14USB: pci-quirks: Fix HCCPARAMS register error for LS7A EHCIHuacai Chen1-0/+9
LS7A EHCI controller doesn't have extended capabilities, so the EECP (EHCI Extended Capabilities Pointer) field of HCCPARAMS register should be 0x0, but it reads as 0xa0 now. This is a hardware flaw and will be fixed in future, now just clear the EECP field to avoid error messages on boot: ...... [ 0.581675] pci 0000:00:04.1: EHCI: unrecognized capability ff [ 0.581699] pci 0000:00:04.1: EHCI: unrecognized capability ff [ 0.581716] pci 0000:00:04.1: EHCI: unrecognized capability ff [ 0.581851] pci 0000:00:04.1: EHCI: unrecognized capability ff ...... [ 0.581916] pci 0000:00:05.1: EHCI: unrecognized capability ff [ 0.581951] pci 0000:00:05.1: EHCI: unrecognized capability ff [ 0.582704] pci 0000:00:05.1: EHCI: unrecognized capability ff [ 0.582799] pci 0000:00:05.1: EHCI: unrecognized capability ff ...... Cc: stable <stable@kernel.org> Signed-off-by: Baoqi Zhang <zhangbaoqi@loongson.cn> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn> Link: https://lore.kernel.org/r/20250202124935.480500-1-chenhuacai@loongson.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-14iommu/vt-d: Make intel_iommu_drain_pasid_prq() cover faults for RIDLu Baolu1-1/+3
This driver supports page faults on PCI RID since commit <9f831c16c69e> ("iommu/vt-d: Remove the pasid present check in prq_event_thread") by allowing the reporting of page faults with the pasid_present field cleared to the upper layer for further handling. The fundamental assumption here is that the detach or replace operations act as a fence for page faults. This implies that all pending page faults associated with a specific RID or PASID are flushed when a domain is detached or replaced from a device RID or PASID. However, the intel_iommu_drain_pasid_prq() helper does not correctly handle faults for RID. This leads to faults potentially remaining pending in the iommu hardware queue even after the domain is detached, thereby violating the aforementioned assumption. Fix this issue by extending intel_iommu_drain_pasid_prq() to cover faults for RID. Fixes: 9f831c16c69e ("iommu/vt-d: Remove the pasid present check in prq_event_thread") Cc: stable@vger.kernel.org Suggested-by: Kevin Tian <kevin.tian@intel.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Link: https://lore.kernel.org/r/20250121023150.815972-1-baolu.lu@linux.intel.com Reviewed-by: Yi Liu <yi.l.liu@intel.com> Link: https://lore.kernel.org/r/20250211005512.985563-2-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2025-02-14iommu/exynos: Fix typosAndrew Kreimer1-3/+3
There are some typos in comments/messages: - modyfying -> modifying - Unabled -> Unable Fix them via codespell. Signed-off-by: Andrew Kreimer <algonell@gmail.com> Link: https://lore.kernel.org/r/20250210112027.29791-1-algonell@gmail.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2025-02-14iommu: Fix a spelling errorEaswar Hariharan1-1/+1
Fix spelling error IDENITY -> IDENTITY in drivers/iommu/iommu.c. Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Link: https://lore.kernel.org/r/20250128190522.70800-1-eahariha@linux.microsoft.com [ joro: Add commit message ] Signed-off-by: Joerg Roedel <jroedel@suse.de>
2025-02-14iommu/amd: Expicitly enable CNTRL.EPHEn bit in resume pathVasant Hegde2-0/+5
With recent kernel, AMDGPU failed to resume after suspend on certain laptop. Sample log: ----------- Nov 14 11:52:19 Thinkbook kernel: iommu ivhd0: AMD-Vi: Event logged [ILLEGAL_DEV_TABLE_ENTRY device=0000:06:00.0 pasid=0x00000 address=0x135300000 flags=0x0080] Nov 14 11:52:19 Thinkbook kernel: AMD-Vi: DTE[0]: 7d90000000000003 Nov 14 11:52:19 Thinkbook kernel: AMD-Vi: DTE[1]: 0000100103fc0009 Nov 14 11:52:19 Thinkbook kernel: AMD-Vi: DTE[2]: 2000000117840013 Nov 14 11:52:19 Thinkbook kernel: AMD-Vi: DTE[3]: 0000000000000000 This is because in resume path, CNTRL[EPHEn] is not set. Fix this by setting CNTRL[EPHEn] to 1 in resume path if EFR[EPHSUP] is set. Note May be better approach is to save the control register in suspend path and restore it in resume path instead of trying to set indivisual bits. We will have separate patch for that. Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219499 Fixes: c4cb23111103 ("iommu/amd: Add support for enable/disable IOPF") Tested-by: Hamish McIntyre-Bhatty <kernel-bugzilla@regd.hamishmb.com> Signed-off-by: Vasant Hegde <vasant.hegde@amd.com> Link: https://lore.kernel.org/r/20250127094411.5931-1-vasant.hegde@amd.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2025-02-14Merge tag 'drm-fixes-2025-02-14' of https://gitlab.freedesktop.org/drm/kernelLinus Torvalds17-136/+191
Pull drm fixes from Dave Airlie: "Weekly drm fixes pull request, nothing too unusual, the hdmi tests needs a bit of refactoring after lockdep shouted at them, otherwise amdgpu and xe lead and a few misc otherwise. amdgpu: - Fix shutdown regression on old APUs - Fix compute queue hang on gfx9 APUs - Fix possible invalid access in PSP failure path - Avoid possible buffer overflow in pptable override amdkfd: - Properly free gang bo in failure path - GFX12 trap handler fix i915: - selftest fix: avoid using uninitialized context xe: - Remove bo->clients out of bos_lock area - Carve out wopcm portion from the stolen memory tests: - fix lockdep with hdmi infrastructure tests host1x: - fix uninitialised mutex usage panthor: - fix uninit variable hibmc: - fix missing Kconfig select" * tag 'drm-fixes-2025-02-14' of https://gitlab.freedesktop.org/drm/kernel: drm: Fix DSC BPP increment decoding drm/amdgpu: avoid buffer overflow attach in smu_sys_set_pp_table() drm/amdkfd: Ensure consistent barrier state saved in gfx12 trap handler drm/amdgpu: bail out when failed to load fw in psp_init_cap_microcode() amdkfd: properly free gang_ctx_bo when failed to init user queue drm/amdgpu: bump version for RV/PCO compute fix drm/amdgpu/gfx9: manually control gfxoff for CS on RV drm/amdgpu/pm: fix UVD handing in amdgpu_dpm_set_powergating_by_smu() drm/xe: Carve out wopcm portion from the stolen memory drm/i915/selftests: avoid using uninitialized context drm/xe/client: bo->client does not need bos_lock drm/hisilicon/hibmc: select CONFIG_DRM_DISPLAY_DP_HELPER drm/panthor: avoid garbage value in panthor_ioctl_dev_query() gpu: host1x: Fix a use of uninitialized mutex drm/tests: hdmi: Fix recursive locking drm/tests: hdmi: Reorder DRM entities variables assignment drm/tests: hdmi: Remove redundant assignments drm/tests: hdmi: Fix WW_MUTEX_SLOWPATH failures
2025-02-14Merge tag 'drm-xe-fixes-2025-02-13' of ↵Dave Airlie2-25/+31
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes - Remove bo->clients out of bos_lock area (Tejas) - Carve out wopcm portion from the stolen memory (Nirmoy) Signed-off-by: Dave Airlie <airlied@redhat.com> From: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/Z64rCicgpBe_t5GY@intel.com
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-27 12:36:40 +0300