| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As it turns out, vendor HDMI PHY driver for H6 has a pretty big table
of predefined values for various pixel clocks. However, most of them are
not useful/tested because they come from reference driver code. Vendor
PHY driver is concerned with only few of those, namely 27 MHz, 74.25
MHz, 148.5 MHz, 297 MHz and 594 MHz. These are all frequencies for
standard CEA modes.
Fix sun50i_h6_cur_ctr and sun50i_h6_phy_config with the values only for
aforementioned frequencies.
Table sun50i_h6_mpll_cfg doesn't need to be changed because values are
actually frequency dependent and not so much SoC dependent. See i.MX6
documentation for explanation of those values for similar PHY.
Fixes: c71c9b2fee17 ("drm/sun4i: Add support for Synopsys HDMI PHY")
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-5-jernej.skrabec@siol.net
|
|
As expected, HDMI controller clock should always match pixel clock. In
the past, changing HDMI controller rate would seemingly worsen
situation. However, that was the result of other bugs which are now
fixed.
Fix that by removing set_rate quirk and always set clock rate.
Fixes: 40bb9d3147b2 ("drm/sun4i: Add support for H6 DW HDMI controller")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-4-jernej.skrabec@siol.net
|
|
Channel 1 has polarity bits for vsync and hsync signals but driver never
sets them. It turns out that with pre-HDMI2 controllers seemingly there
is no issue if polarity is not set. However, with HDMI2 controllers
(H6) there often comes to de-synchronization due to phase shift. This
causes flickering screen. It's safe to assume that similar issues might
happen also with pre-HDMI2 controllers.
Solve issue with setting vsync and hsync polarity. Note that display
stacks with tcon top have polarity bits actually in tcon0 polarity
register.
Fixes: 9026e0d122ac ("drm: Add Allwinner A10 Display Engine support")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-3-jernej.skrabec@siol.net
|
|
We don't have a persistent fb holding a reference to the frontbuffer
object, so every time we do the get+put we throw the frontbuffer object
immediately away. And so the next time around we get a pristine
frontbuffer object with bits==0 even for the old vma. This confuses
the frontbuffer tracking code which understandably expects the old
frontbuffer to have the overlay's bit set.
Fix this by hanging on to the frontbuffer reference until the next
flip. And just to make this a bit more clear let's track the frontbuffer
explicitly instead of just grabbing it via the old vma.
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1136
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209021918.16234-2-ville.syrjala@linux.intel.com
Fixes: 8e7cb1799b4f ("drm/i915: Extract intel_frontbuffer active tracking")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 553c23bdb4775130f333f07a51b047276bc53f79)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
This reverts commit 4a3dea8932d3b1199680d2056dd91d31d94d70b7.
This causes blank screens for some users.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1482
Cc: Alvin Lee <alvin.lee2@amd.com>
Cc: Jun Lei <Jun.Lei@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c fix from Alexandre Belloni:
"A single build warning fix"
* tag 'i3c/fixes-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c/master/mipi-i3c-hci: Fix position of __maybe_unused in i3c_hci_of_match
|
|
The index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this index before using it in hclge_get_rss_key().
Fixes: a638b1d8cc87 ("net: hns3: fix get VF RSS issue")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tqp_index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this tqp_index before using it in hclge_get_ring_chain_from_mbx().
Fixes: 84e095d64ed9 ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The queue_id is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this queue_id before using it in hclge_reset_vf_queue().
Fixes: 1a426f8b40fc ("net: hns3: fix the VF queue reset flow error")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b13f ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TypeC FIA can be powered down if the TC-COLD power state is allowed,
so block the TC-COLD state when initializing the FIA.
Note that this isn't needed on ICL where the FIA is never modular and
which has no generic way to block TC-COLD (except for platforms with a
legacy TypeC port and on those too only via these legacy ports, not via
a DP-alt/TBT port).
Cc: <stable@vger.kernel.org> # v5.10+
Cc: José Roberto de Souza <jose.souza@intel.com>
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3027
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210208154303.6839-1-imre.deak@intel.com
Reviewed-by: Jos� Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit f48993e5d26b079e8c80fff002499a213dbdb1b4)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The sdebug_q_arr pointer must be freed when the module is unloaded.
$ cat /sys/kernel/debug/kmemleak
unreferenced object 0xffff888e1cfb0000 (size 4096):
comm "modprobe", pid 165555, jiffies 4325987516 (age 685.194s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000458f4f5d>] 0xffffffffc06702d9
[<000000003edc4b1f>] do_one_initcall+0xe9/0x57d
[<00000000da7d518c>] do_init_module+0x1d1/0x6f0
[<000000009a6a9248>] load_module+0x36bd/0x4f50
[<00000000ddb0c3ce>] __do_sys_init_module+0x1db/0x260
[<000000009532db57>] do_syscall_64+0xa5/0x420
[<000000002916b13d>] entry_SYSCALL_64_after_hwframe+0x6a/0xdf
Fixes: 87c715dcde63 ("scsi: scsi_debug: Add per_host_store option")
Link: https://lore.kernel.org/r/20210208111734.34034-1-mlombard@redhat.com
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This reverts commit 32cf1a12cad43358e47dac8014379c2f33dfbed4.
The 'exisitng buffer' in this case is the firmware provided table, and
we should not modify that in place. This fixes a crash on arm64 with
initrd table overrides, in which case the DSDT is not mapped with
read/write permissions.
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If the maximum performance level taken for computing the
arch_max_freq_ratio value used in the x86 scale-invariance code is
higher than the one corresponding to the cpuinfo.max_freq value
coming from the acpi_cpufreq driver, the scale-invariant utilization
falls below 100% even if the CPU runs at cpuinfo.max_freq or slightly
faster, which causes the schedutil governor to select a frequency
below cpuinfo.max_freq. That frequency corresponds to a frequency
table entry below the maximum performance level necessary to get to
the "boost" range of CPU frequencies which prevents "boost"
frequencies from being used in some workloads.
While this issue is related to scale-invariance, it may be amplified
by commit db865272d9c4 ("cpufreq: Avoid configuring old governors as
default with intel_pstate") from the 5.10 development cycle which
made it extremely easy to default to schedutil even if the preferred
driver is acpi_cpufreq as long as intel_pstate is built too, because
the mere presence of the latter effectively removes the ondemand
governor from the defaults. Distro kernels are likely to include
both intel_pstate and acpi_cpufreq on x86, so their users who cannot
use intel_pstate or choose to use acpi_cpufreq may easily be
affectecd by this issue.
If CPPC is available, it can be used to address this issue by
extending the frequency tables created by acpi_cpufreq to cover the
entire available frequency range (including "boost" frequencies) for
each CPU, but if CPPC is not there, acpi_cpufreq has no idea what
the maximum "boost" frequency is and the frequency tables created by
it cannot be extended in a meaningful way, so in that case make it
ask the arch scale-invariance code to to use the "nominal" performance
level for CPU utilization scaling in order to avoid the issue at hand.
Fixes: db865272d9c4 ("cpufreq: Avoid configuring old governors as default with intel_pstate")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
|
|
A severe performance regression on AMD EPYC processors when using
the schedutil scaling governor was discovered by Phoronix.com and
attributed to the following commits:
41ea667227ba ("x86, sched: Calculate frequency invariance for AMD
systems")
976df7e5730e ("x86, sched: Use midpoint of max_boost and max_P for
frequency invariance on AMD EPYC")
The source of the problem is that the maximum performance level taken
for computing the arch_max_freq_ratio value used in the x86 scale-
invariance code is higher than the one corresponding to the
cpuinfo.max_freq value coming from the acpi_cpufreq driver.
This effectively causes the scale-invariant utilization to fall below
100% even if the CPU runs at cpuinfo.max_freq or slightly faster, so
the schedutil governor selects a frequency below cpuinfo.max_freq
then. That frequency corresponds to a frequency table entry below
the maximum performance level necessary to get to the "boost" range
of CPU frequencies.
However, if the cpuinfo.max_freq value coming from acpi_cpufreq was
higher, the schedutil governor would select higher frequencies which
in turn would allow acpi_cpufreq to set more adequate performance
levels and to get to the "boost" range of CPU frequencies more often.
This issue affects any systems where acpi_cpufreq is used and the
"boost" (or "turbo") frequencies are enabled, not just AMD EPYC.
Moreover, commit db865272d9c4 ("cpufreq: Avoid configuring old
governors as default with intel_pstate") from the 5.10 development
cycle made it extremely easy to default to schedutil even if the
preferred driver is acpi_cpufreq as long as intel_pstate is built
too, because the mere presence of the latter effectively removes the
ondemand governor from the defaults. Distro kernels are likely to
include both intel_pstate and acpi_cpufreq on x86, so their users
who cannot use intel_pstate or choose to use acpi_cpufreq may
easily be affectecd by this issue.
To address this issue, extend the frequency table constructed by
acpi_cpufreq for each CPU to cover the entire range of available
frequencies (including the "boost" ones) if CPPC is available and
indicates that "boost" (or "turbo") frequencies are enabled. That
causes cpuinfo.max_freq to become the maximum "boost" frequency of
the given CPU (instead of the maximum frequency returned by the ACPI
_PSS object that corresponds to the "nominal" performance level).
Fixes: 41ea667227ba ("x86, sched: Calculate frequency invariance for AMD systems")
Fixes: 976df7e5730e ("x86, sched: Use midpoint of max_boost and max_P for frequency invariance on AMD EPYC")
Fixes: db865272d9c4 ("cpufreq: Avoid configuring old governors as default with intel_pstate")
Link: https://www.phoronix.com/scan.php?page=article&item=linux511-amd-schedutil&num=1
Link: https://lore.kernel.org/linux-pm/20210203135321.12253-2-ggherdovich@suse.cz/
Reported-by: Michael Larabel <Michael@phoronix.com>
Diagnosed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Reviewed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Tested-by: Michael Larabel <Michael@phoronix.com>
|
|
This reverts commit 842067940a3e3fc008a60fee388e000219b32632.
For some solutions e.g. sound/soc/intel/catpt, DW DMA is part of a
compound device (in that very example, domains: ADSP, SSP0, SSP1, DMA0
and DMA1 are part of a single entity) rather than being a standalone
one. Driver for said device may enlist DMA to transfer data during
suspend or resume sequences.
Manipulating RPM explicitly in dw's DMA request and release channel
functions causes suspend() to also invoke resume() for the exact same
device. Similar situation occurs for resume() sequence. Effectively
renders device dysfunctional after first suspend() attempt. Revert the
change to address the problem.
Fixes: 842067940a3e ("dmaengine: dw: Enable runtime PM")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210203191924.15706-1-cezary.rojewski@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A fix for a crash scenario that has been present since the initial
merge, a minor regression in sysfs attribute visibility, and a fix for
some flexible array warnings.
The bulk of this pull is an update to the libnvdimm unit test
infrastructure to test non-ACPI platforms. Given there is zero
regression risk for test updates, and the tests enable validation of
bits headed towards the next merge window, I saw no reason to hold the
new tests back. Santosh originally submitted this before the v5.11
window opened.
Summary:
- Fix a crash when sysfs accesses race 'dimm' driver probe/remove.
- Fix a regression in 'resource' attribute visibility necessary for
mapping badblocks and other physical address interrogations.
- Fix some flexible array warnings
- Expand the unit test infrastructure for non-ACPI platforms"
* tag 'libnvdimm-fixes-5.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/dimm: Avoid race between probe and available_slots_show()
ndtest: Add papr health related flags
ndtest: Add nvdimm control functions
ndtest: Add regions and mappings to the test buses
ndtest: Add dimm attributes
ndtest: Add dimms to the two buses
ndtest: Add compatability string to treat it as PAPR family
testing/nvdimm: Add test module for non-nfit platforms
libnvdimm/namespace: Fix visibility of namespace resource attribute
libnvdimm/pmem: Remove unused header
ACPI: NFIT: Fix flexible_array.cocci warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Borislav Petkov:
"Two more timers-related fixes for v5.11:
- Use a freezable workqueue for RTC sync because the sync can happen
at any time and trigger suspend assertion checks in the i2c
subsystem.
- Correct a previous RTC validation change to check only bit 6 in
register D because some Intel machines use bits 0-5"
* tag 'timers_urgent_for_v5.11_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ntp: Use freezable workqueue for RTC synchronization
rtc: mc146818: Dont test for bit 0-5 in Register D
|
|
The verdict returned from ena_xdp_execute() is used to determine the
fate of the RX buffer's page. In case of XDP Redirect/TX error the
verdict should be set to XDP_ABORTED, otherwise the page won't be freed.
Fixes: a318c70ad152 ("net: ena: introduce XDP redirect implementation")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small, last-minute, USB driver fixes for 5.11-rc7
They all resolve issues reported, or are a few new device ids for some
drivers. They include:
- new device ids for some usb-serial drivers
- xhci fixes for a variety of reported problems
- dwc3 driver bugfixes
- dwc2 driver bugfixes
- usblp driver bugfix
- thunderbolt bugfix
- few other tiny fixes
All have been in linux-next with no reported issues"
* tag 'usb-5.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: dwc2: Fix endpoint direction check in ep_from_windex
usb: dwc3: fix clock issue during resume in OTG mode
xhci: fix bounce buffer usage for non-sg list case
usb: host: xhci: mvebu: make USB 3.0 PHY optional for Armada 3720
usb: xhci-mtk: break loop when find the endpoint to drop
usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints
usb: renesas_usbhs: Clear pipe running flag in usbhs_pkt_pop()
USB: gadget: legacy: fix an error code in eth_bind()
thunderbolt: Fix possible NULL pointer dereference in tb_acpi_add_link()
USB: serial: option: Adding support for Cinterion MV31
usb: xhci-mtk: fix unreleased bandwidth data
usb: gadget: aspeed: add missing of_node_put
USB: usblp: don't call usb_set_interface if there's a single alt
USB: serial: cp210x: add pid/vid for WSDA-200-USB
USB: serial: cp210x: add new VID/PID for supporting Teraoka AD2000
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Nothing terribly interesting, just a few fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - sync supported devices with fork on GitHub
Input: ariel-pwrbutton - remove unused variable ariel_pwrbutton_id_table
Input: goodix - add support for Goodix GT9286 chip
dt-bindings: input: touchscreen: goodix: Add binding for GT9286 IC
dt-bindings: input: adc-keys: clarify description
Input: ili210x - implement pressure reporting for ILI251x
Input: i8042 - unbreak Pegatron C15B
Input: st1232 - wait until device is ready before reading resolution
Input: st1232 - do not read more bytes than needed
Input: st1232 - fix off-by-one error in resolution handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One fix in drivers (lpfc) that stops an oops on resource exhaustion"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Fix EEH encountering oops with NVMe traffic
|
|
Pull block fixes from Jens Axboe:
"A few small regression fixes:
- NVMe pull request from Christoph:
- more quirks for buggy devices (Thorsten Leemhuis, Claus Stovgaard)
- update the email address for Keith (Keith Busch)
- fix an out of bounds access in nvmet-tcp (Sagi Grimberg)
- Regression fix for BFQ shallow depth calculations introduced in
this merge window (Lin)"
* tag 'block-5.11-2021-02-05' of git://git.kernel.dk/linux-block:
nvmet-tcp: fix out-of-bounds access when receiving multiple h2cdata PDUs
bfq-iosched: Revert "bfq: Fix computation of shallow depth"
update the email address for Keith Bush
nvme-pci: ignore the subsysem NQN on Phison E16
nvme-pci: avoid the deepest sleep state on Kingston A2000 SSDs
|
|
Normally we clear the failover_pending flag when processing the reset.
But if we are unable to schedule a failover reset we must clear the
flag ourselves. We could fail to schedule the reset if we are in PROBING
state (eg: when booting via kexec) or because we could not allocate memory.
Thanks to Cris Forno for helping isolate the problem and for testing.
Fixes: 1d8504937478 ("powerpc/vnic: Extend "failover pending" window")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Tested-by: Cristobal Forno <cforno12@linux.ibm.com>
Link: https://lore.kernel.org/r/20210203050802.680772-1-sukadev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.11
Third, and most likely the last, set of fixes for v5.11. Two very
small fixes.
ath9k
* fix build regression related to LEDS_CLASS
mt76
* fix a memory leak
* tag 'wireless-drivers-2021-02-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
mt76: dma: fix a possible memory leak in mt76_add_fragment()
ath9k: fix build error with LEDS_CLASS=m
====================
Link: https://lore.kernel.org/r/20210205163434.14D94C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When disable CBS, mode_to_use parameter is not updated even the operation
mode of Tx Queue is changed to Data Centre Bridging (DCB). Therefore,
when tc_setup_cbs() function is called to re-enable CBS, the operation
mode of Tx Queue remains at DCB, which causing CBS fails to work.
This patch updates the value of mode_to_use parameter to MTL_QUEUE_DCB
after operation mode of Tx Queue is changed to DCB in stmmac_dma_qmode()
callback function.
Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC")
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Song, Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Link: https://lore.kernel.org/r/1612447396-20351-1-git-send-email-yoong.siang.song@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The XDP frame's headroom might be large enough to accommodate the
xdpf backpointer as well as shifting the data to an aligned address.
Try this first before resorting to allocating a new buffer and copying
the data.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 256 byte data alignment is required for preventing DMA transaction
splits when crossing 4K page boundaries. Since XDP deals only with page
sized buffers or less, this restriction isn't needed. Instead, the data
only needs to be aligned to 64 bytes to prevent DMA transaction splits.
These lessened restrictions can increase performance by widening the pool
of permitted data alignments and preventing unnecessary realignments.
Fixes: ae680bcbd06a ("dpaa_eth: implement the A050385 erratum workaround for XDP")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the erratum workaround is triggered, the newly created xdp_frame
structure is stored at the start of the newly allocated buffer. Avoid
the structure from being overwritten by explicitly reserving enough
space in the buffer for storing it.
Account for the fact that the structure's size might increase in time by
aligning the headroom to DPAA_FD_DATA_ALIGNMENT bytes, thus guaranteeing
the data's alignment.
Fixes: ae680bcbd06a ("dpaa_eth: implement the A050385 erratum workaround for XDP")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull vdpa fix from Michael Tsirkin:
"A bugfix in the mlx driver I got at the last minute"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Restore the hardware used index after change map
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Limit retries when analyse of SDIO tuples fails
MMC host:
- sdhci: Fix linking err for sdhci-brcmstb"
* tag 'mmc-v5.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-pltfm: Fix linking err for sdhci-brcmstb
mmc: core: Limit retries when analyse of SDIO tuples fails
|
|
Pull drm fixes from Dave Airlie:
"Fixes for rc7, bit bigger than I'd like at this stage, but most of the
i915 stuff and some amdgpu is destined for staging and I'd rather not
hold it up, the i915 changes also pulled in a few precusor code
movement patches to make things cleaner, but nothing seems that
horrible, and I've checked over all of it.
Otherwise there is a nouveau dma-api warning regression, and a ttm
page allocation warning fix, and some fixes for a bridge chip,
ttm:
- fix huge page warning regression
i915:
- Skip vswing programming for TBT
- Power up combo PHY lanes for HDMI
- Fix double YUV range correction on HDR planes
- Fix the MST PBN divider calculation
- Fix LTTPR vswing/pre-emp setting in non-transparent mode
- Move the breadcrumb to the signaler if completed upon cancel
- Close race between enable_breadcrumbs and cancel_breadcrumbs
- Drop lru bumping on display unpinning
amdgpu:
- Fix retry in gem create
- Vangogh fixes
- Fix for display from shared buffers
- Various display fixes
amdkfd:
- Fix regression in buffer free
nouveau:
- fix DMA API warning regression
drm/bridge/lontium-lt9611uxc:
- EDID fixes
- Don't handle hotplug events in IRQ handler"
* tag 'drm-fixes-2021-02-05-1' of git://anongit.freedesktop.org/drm/drm: (29 commits)
drm/nouveau: fix dma syncing warning with debugging on.
drm/amd/display: Decrement refcount of dc_sink before reassignment
drm/amd/display: Free atomic state after drm_atomic_commit
drm/amd/display: Fix dc_sink kref count in emulated_link_detect
drm/amd/display: Release DSC before acquiring
drm/amd/display: Revert "Fix EDID parsing after resume from suspend"
drm/amd/display: Add more Clock Sources to DCN2.1
drm/amd/display: reuse current context instead of recreating one
drm/amd/display: Fix DPCD translation for LTTPR AUX_RD_INTERVAL
drm/amdgpu: enable freesync for A+A configs
drm/amd/pm: fill in the data member of v2 gpu metrics table for vangogh
drm/amdgpu/gfx10: update CGTS_TCC_DISABLE and CGTS_USER_TCC_DISABLE register offsets for VGH
drm/amdkfd: fix null pointer panic while free buffer in kfd
drm/amdgpu: fix the issue that retry constantly once the buffer is oversize
drm/i915/dp: Fix LTTPR vswing/pre-emp setting in non-transparent mode
drm/i915/dp: Move intel_dp_set_signal_levels() to intel_dp_link_training.c
drm/i915: Fix the MST PBN divider calculation
drm/dp/mst: Export drm_dp_get_vc_payload_bw()
drm/i915/gem: Drop lru bumping on display unpinning
drm/i915/gt: Close race between enable_breadcrumbs and cancel_breadcrumbs
...
|
|
When a change of memory map occurs, the hardware resources are destroyed
and then re-created again with the new memory map. In such case, we need
to restore the hardware available and used indices. The driver failed to
restore the used index which is added here.
Also, since the driver also fails to reset the available and used
indices upon device reset, fix this here to avoid regression caused by
the fact that used index may not be zero upon device reset.
Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20210204073618.36336-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
dwc2_hsotg_process_req_status uses ep_from_windex() to retrieve
the endpoint for the index provided in the wIndex request param.
In a test-case with a rndis gadget running and sending a malformed
packet to it like:
dev.ctrl_transfer(
0x82, # bmRequestType
0x00, # bRequest
0x0000, # wValue
0x0001, # wIndex
0x00 # wLength
)
it is possible to cause a crash:
[ 217.533022] dwc2 ff300000.usb: dwc2_hsotg_process_req_status: USB_REQ_GET_STATUS
[ 217.559003] Unable to handle kernel read from unreadable memory at virtual address 0000000000000088
...
[ 218.313189] Call trace:
[ 218.330217] ep_from_windex+0x3c/0x54
[ 218.348565] usb_gadget_giveback_request+0x10/0x20
[ 218.368056] dwc2_hsotg_complete_request+0x144/0x184
This happens because ep_from_windex wants to compare the endpoint
direction even if index_to_ep() didn't return an endpoint due to
the direction not matching.
The fix is easy insofar that the actual direction check is already
happening when calling index_to_ep() which will return NULL if there
is no endpoint for the targeted direction, so the offending check
can go away completely.
Fixes: c6f5c050e2a7 ("usb: dwc2: gadget: add bi-directional endpoint support")
Cc: stable@vger.kernel.org
Reported-by: Gerhard Klostermeier <gerhard.klostermeier@syss.de>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20210127103919.58215-1-heiko@sntech.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit fe8abf332b8f ("usb: dwc3: support clocks and resets for DWC3
core") introduced clock support and a new function named
dwc3_core_init_for_resume() which enables the clock before calling
dwc3_core_init() during resume as clocks get disabled during suspend.
Unfortunately in this commit the DWC3_GCTL_PRTCAP_OTG case was forgotten
and therefore during resume, a platform could call dwc3_core_init()
without re-enabling the clocks first, preventing to resume properly.
So update the resume path to call dwc3_core_init_for_resume() as it
should.
Fixes: fe8abf332b8f ("usb: dwc3: support clocks and resets for DWC3 core")
Cc: stable@vger.kernel.org
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Link: https://lore.kernel.org/r/20210125161934.527820-1-gary.bisson@boundarydevices.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Michael tried to enable Advanced Error Reporting through the ENETC's
Root Complex Event Collector, and the system started spitting out single
bit correctable ECC errors coming from the ENETC interfaces:
pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
fsl_enetc 0000:00:00.0: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.0: device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.0: [14] CorrIntErr
fsl_enetc 0000:00:00.1: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.1: device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.1: [14] CorrIntErr
Further investigating the port correctable memory error detect register
(PCMEDR) shows that these AER errors have an associated SOURCE_ID of 6
(RFS/RSS):
$ devmem 0x1f8010e10 32
0xC0000006
$ devmem 0x1f8050e10 32
0xC0000006
Discussion with the hardware design engineers reveals that on LS1028A,
the hardware does not do initialization of that RFS/RSS memory, and that
software should clear/initialize the entire table before starting to
operate. That comes as a bit of a surprise, since the driver does not do
initialization of the RFS memory. Also, the initialization of the
Receive Side Scaling is done only partially.
Even though the entire ENETC IP has a single shared flow steering
memory, the flow steering service should returns matches only for TCAM
entries that are within the range of the Station Interface that is doing
the search. Therefore, it should be sufficient for a Station Interface
to initialize all of its own entries in order to avoid any ECC errors,
and only the Station Interfaces in use should need initialization.
There are Physical Station Interfaces associated with PCIe PFs and
Virtual Station Interfaces associated with PCIe VFs. We let the PF
driver initialize the entire port's memory, which includes the RFS
entries which are going to be used by the VF.
Reported-by: Michael Walle <michael@walle.cc>
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210204134511.2640309-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 44144185951a0f ("hv_netvsc: Add validation for untrusted Hyper-V
values") added validation to rndis_filter_receive_data() (and
rndis_filter_receive()) which introduced NVSP_STAT_FAIL-scenarios where
the count is not updated/reset. Fix this omission, and prevent similar
scenarios from occurring in the future.
Reported-by: Juan Vazquez <juvazq@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Fixes: 44144185951a0f ("hv_netvsc: Add validation for untrusted Hyper-V values")
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210203113602.558916-1-parri.andrea@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In gsi_channel_setup(), we check to see if the configuration data
contains any information about channels that are not supported by
the hardware. If one is found, we abort the setup process, but
the error code (ret) is not set in this case. Fix this bug.
Fixes: 650d1603825d8 ("soc: qcom: ipa: the generic software interface")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210204010655.15619-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It's not meaningful to pass on LAPB error codes to HDLC code or other
parts of the system, because they will not understand the error codes.
Instead, use system-wide recognizable error codes.
Fixes: f362e5fe0f1f ("wan/hdlc_x25: make lapb params configurable")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20210203071541.86138-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Link: https://lore.kernel.org/r/20210202182511.8109-1-rajur@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.11-rc7:
- Skip vswing programming for TBT
- Power up combo PHY lanes for HDMI
- Fix double YUV range correction on HDR planes
- Fix the MST PBN divider calculation
- Fix LTTPR vswing/pre-emp setting in non-transparent mode
- Move the breadcrumb to the signaler if completed upon cancel
- Close race between enable_breadcrumbs and cancel_breadcrumbs
- Drop lru bumping on display unpinning
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87bld0f36b.fsf@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Revert ASPM suspend/resume fix that regressed NVMe devices (Bjorn
Helgaas)"
* tag 'pci-v5.11-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI/ASPM: Save/restore L1SS Capability for suspend/resume"
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.11-2021-02-03:
amdgpu:
- Fix retry in gem create
- Vangogh fixes
- Fix for display from shared buffers
- Various display fixes
amdkfd:
- Fix regression in buffer free
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210204041300.4425-1-alexander.deucher@amd.com
|
|
Since commit 23025393dbeb3b8b3 ("xen/netback: use lateeoi irq binding")
xenvif_rx_ring_slots_available() is no longer called only from the rx
queue kernel thread, so it needs to access the rx queue with the
associated queue held.
Reported-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Fixes: 23025393dbeb3b8b3 ("xen/netback: use lateeoi irq binding")
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Wei Liu <wl@xen.org>
Link: https://lore.kernel.org/r/20210202070938.7863-1-jgross@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Address recent regression causing battery devices to be never bound to
a driver on some systems (Hans de Goede)"
* tag 'acpi-5.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: scan: Fix battery devices sometimes never binding
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
* drm/bridge/lontium-lt9611uxc: EDID fixes; Don't handle hotplug
events in IRQ handler
* drm/ttm: Use _GFP_NOWARN for huge pages
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YBlHU4sc/5GHpXpg@linux-uq9g
|
|
Adding support for Cinterion MV31 with PID 0x00B7.
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 1
P: Vendor=1e2d ProdID=00b7 Rev=04.14
S: Manufacturer=Cinterion
S: Product=Cinterion USB Mobile Broadband
S: SerialNumber=b3246eed
C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
Signed-off-by: Christoph Schemmel <christoph.schemmel@gmail.com>
Link: https://lore.kernel.org/r/20210202084523.4371-1-christoph.schemmel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since I wrote the below patch if you run a debug kernel you can a
dma debug warning like:
nouveau 0000:1f:00.0: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000016e012000] [size=4096 bytes]
The old nouveau code wasn't consolidate the pages like the ttm code,
but the dma-debug expects the sync code to give it the same base/range
pairs as the allocator.
Fix the nouveau sync code to consolidate pages before calling the
sync code.
Fixes: bd549d35b4be0 ("nouveau: use ttm populate mapping functions. (v2)")
Reported-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/417588/
|
|
Reporting a port as connected if nothing is attached to them leads to
any i2c transactions on this port trying to use an uninitialized i2c
adapter, fix this.
Let's account for this case even if branch devices have no good reason
to report a port as plugged with their peer device type set to 'none'.
Fixes: db1a07956968 ("drm/dp_mst: Handle SST-only branch device case")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/2987
References: https://gitlab.freedesktop.org/drm/intel/-/issues/1963
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v5.5+
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reported-by: Thiago Macieira <gitlab@gitlab.freedesktop.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210201120145.350258-1-imre.deak@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"The code fixes in this round are all for the Texas Instruments OMAP
platform, addressing several regressions related to the ti-sysc
interconnect changes that was merged in linux-5.11 and one recently
introduced RCU usage warning.
Tero Kristo updates his maintainer file entries as he is changing to a
new employer.
The other changes are for devicetree files across eight different
platforms:
TI OMAP:
- multiple gpio related one-line fixes
Allwinner/sunxi:
- ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
- soc: sunxi: mbus: Remove DE2 display engine compatibles
NXP lpc32xx:
- ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL
STMicroelectronics stm32
- multiple minor fixes for DHCOM/DHCOR boards
NXP Layerscape:
- Fix DCFG address range on LS1046A SoC
Amlogic meson:
- fix reboot issue on odroid C4
- revert an ethernet change that caused a regression
- meson-g12: Set FL-adj property value
Rockchip:
- multiple minor fixes on 64-bit rockchip machines
Qualcomm:
- Regression fixes for Lenovo Yoga touchpad and for interconnect
configuration
- Boot fixes for 'LPASS' clock configuration on two machines"
* tag 'arm-soc-fixes-v5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL
ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
arm64: dts: ls1046a: fix dcfg address range
soc: sunxi: mbus: Remove DE2 display engine compatibles
arm64: dts: meson: switch TFLASH_VDD_EN pin to open drain on Odroid-C4
Revert "arm64: dts: amlogic: add missing ethernet reset ID"
arm64: dts: rockchip: Disable display for NanoPi R2S
ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
arm64: dts: rockchip: remove interrupt-names property from rk3399 vdec node
drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
ARM: dts: stm32: Fix GPIO hog names on DHCOM
ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
ARM: dts: stm32: Disable WP on DHCOM uSD slot
ARM: dts: stm32: Connect card-detect signal on DHCOM
ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect
arm64: dts: qcom: sdm845: Reserve LPASS clocks in gcc
...
|
