summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2010-12-03sfc: Remove broken automatic fallback for invalid Falcon chip/board configBen Hutchings1-33/+24
If the Falcon board config is invalid, we cannot proceed - we do not have a valid board type to pass to falcon_probe_board(), and if we kluge that to work with an unknown board then other initialisation code will crash. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-03sfc: Fix event based MCDI completion and MC REBOOT/CMDDONE ordering issueSteve Hodgson1-0/+1
The mcfw *never* sends CMDDONE when rebooting. Changing this so that it always sends CMDDONE *before* REBOOT is easy on Siena, but it's not obvious that we could guarantee to be able to implement this on future hardware. Given this, I'm less convinced that the protocol should be changed. To reiterate the failure mode: The driver sees this: issue command receive REBOOT event Was that reboot event sent before the command was issued, or in response to the command? If the former then there will be a subsequent CMDDONE event, if the latter, then there will be no CMDDONE event. Options to resolve this are: 1. REBOOT always completes an outstanding mcdi request, and we set the credits count to ignore a subsequent CMDDONE event with mismatching seqno. 2. REBOOT never completes an outstanding mcdi request. If there is no CMDDONE event then we rely on the mcdi timeout code to complete the outstanding request, incurring a 10s delay. I'd argue that (2) is tidier, but that incurring a 10s delay is a little needless. Let's go with (1). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-03sfc: Clear RXIN_SEL when soft-resetting QT2025CBen Hutchings1-0/+6
When we enable PMA/PMD loopback this automatically sets RXIN_SEL (inverse polarity for RXIN). We need to clear that bit during the soft-reset sequence, as it is not done automatically. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-03sfc: Read-to-clear LM87 alarm/interrupt status at start of dayBen Hutchings1-0/+4
We do not want to shut down the board based on a fault that has already been cleared. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-03sfc: Distinguish critical and non-critical over-temperature conditionsBen Hutchings1-29/+80
Set both the 'maximum' and critical temperature limits for LM87 hardware monitors on Falcon boards. Do not shut down a port until the critical temperature is reached, but warn as soon as the 'maximum' temperature is reached. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-03sfc: Fix condition for no-op in set_phy_flash_cfg()Ben Hutchings1-1/+1
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-03sfc: Reduce log level for MCDI error response in efx_mcdi_rpc()Ben Hutchings1-1/+1
Some errors are expected, e.g. when sending new commands to an MC running old firmware. Only the caller of efx_mcdi_rpc() can decide what is a real error. Therefore log the error responses with netif_dbg(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-03can: EG20T PCH: Delete unnecessary spin_lockTomoya1-34/+0
Delete unnecessary spin_lock for accessing Message Object. Since all message objects are divided into tx/rx area completely, spin_lock processing is unnecessary. Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-03can: EG20T PCH: Enumerate LEC macrosTomoya1-36/+41
For easy to readable, LEC #define macros are replaced to enums. Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-03can: EG20T PCH: Change Message Object IndexTomoya1-147/+116
For easy to readable, add Message Object index like below. PCH_RX_OBJ_START PCH_RX_OBJ_END PCH_TX_OBJ_START PCH_TX_OBJ_END Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-03can: EG20T PCH: Separate Interface Register(IF1/IF2)Tomoya1-244/+201
CAN register of Intel PCH EG20T has 2 sets of interface register. To reduce whole of code size, separate interface register. As a result, the number of function also can be reduced. Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-02vxge: update driver versionJon Mason1-2/+2
Update vxge driver version Signed-off-by: Jon Mason <jon.mason@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-02vxge: use strcpy for stringsJon Mason1-1/+1
Use strncpy instead of memcpy when working on strings Signed-off-by: Jon Mason <jon.mason@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-02vxge: remove unnecessary printksJon Mason1-11/+0
Remove printks for ring blocks, fifo blocks, and rx doorbell mode as they clutter the dmesg output during modprobe and provide no useful information. Signed-off-by: Jon Mason <jon.mason@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-01bnx2x: Add Nic partitioning mode (57712 devices)Dmitry Kravkov7-96/+400
NIC partitioning is another flavor of multi function - having few PCI functions share the same physical port. Unlike the currently supported mode of multi-function which depends on the switch configuration and uses outer-VLAN, the NPAR mode is switch independent and uses the MAC addresses to distribute incoming packets to the different functions. This patch adds the specific HW setting of the NPAR mode and some distinctions between switch dependent (SD) and switch independent (SI) multi-function (MF) modes where the configuration is not the same. Advance driver version to 1.60.00-6 Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: Use netdev_dbg for printk(KERN_DEBUGJoe Perches1-7/+12
Use the normal debugging functions. Print mac address when using random_ether_addr. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: Remove netdev_dbg usesJoe Perches1-133/+0
These were probably just for initial driver debugging and have not been enabled in builds in git history. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: Convert dev_printk(<level> to dev_<level>(Joe Perches1-38/+26
Use vsprintf extension %pM for a mac address in one instance. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: Separate vendor specific initializations into functionsJoe Perches1-179/+188
Neaten the phy_init function by adding and calling vendor specific functions. object size is reduced by ~1kb: $ size drivers/net/forcedeth.o.* text data bss dec hex filename 83475 1848 19304 104627 198b3 drivers/net/forcedeth.o.new 84459 1848 19544 105851 19d7b drivers/net/forcedeth.o.old Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: Add function init_realtek_8211bJoe Perches1-73/+32
Deduplicate the code use for the init/reset of this device. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: Convert pr_<level> to netdev_<level>Joe Perches1-132/+161
Use netdev_<level> when a struct net_device * is available. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: Use pr_fmt and pr_<level>Joe Perches1-114/+142
Convert printks to pr_<level>. Remove "forcedeth: " from some calls as it's now added by pr_fmt. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: Convert remaining dprintk to netdev_dbgJoe Perches1-19/+12
The remaining dprintk uses are emitted as KERN_INFO. Change these dprintk uses to netdev_dbg. Remove the now unused dprintk macros. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: Use print_hex_dumpJoe Perches1-37/+17
Use the standard code to emit hex dumps. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: convert dprintk(KERN_DEBUG to netdev_dbgJoe Perches1-89/+87
Use the more standard macro to preface netdev->name. Fix casting on resource use. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: Change reg_delay arguments and useJoe Perches1-16/+14
Move the printk out of reg_delay and make the callers emit a message on error. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29Merge branch 'for-davem' of ↵David S. Miller136-1837/+11269
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2010-11-29vmxnet3: fix compilation when RSS is disabledScott J. Goldman1-1/+4
If RSS is disabled, we can ifdef out some RSS specific code. This fixes the compile error found by Randy Dunlap. Signed-off-by: Scott J. Goldman <scottjg@vmware.com> Reviewed-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29qeth: l3 fix len in tso hdrFrank Blaschka1-0/+1
The tso hdr is longer then the regular l3 hdr. Fix the calculation of the total len by accounting the size of the tso hdr. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29qeth: enable interface setup if LAN is offlineUrsula Braun2-10/+12
Device initialization of a qeth device contains a STARTLAN step. This step may fail, if cable is not yet plugged in. The qeth device stays in state HARDSETUP until cable is plugged in. This prevents further preparational initialization steps of the qeth device and its network interface. This patch makes sure initialization of qeth device continues, even though cable is not yet plugged in. Once carrier is available, qeth is notified, triggers a recovery which results in a working network interface. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29drivers/s390/net: Remove unnecessary semicolonsJoe Perches1-1/+1
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29qeth lcs: convert mc rwlock to RCUSachin Sant2-9/+12
Commit 1d7138de878d1d4210727c1200193e69596f93b3 igmp: RCU conversion of in_dev->mc_list converted rwlock to RCU. Update the s390 network drivers(qeth & lcs) code to adapt to this change. V2 : Changes based on suggestions given by Eric Dumazet Signed-off-by: Sachin Sant <sachinp@in.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29stmmac: fix stmmac_resume removing not yet used shutdown flagGiuseppe Cavallaro1-7/+0
The commit to convert to use the dev_pm_ops struct introduces a bug. The shutdown flag is not yet used because the hibernation on memory is done by using the freeze callback. Thanks to Vlad for having reported it. Reported-by: Vlad Lungu <vlad.lungu@windriver.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: use usleep_range not msleep for small sleepsSzymon Janc1-1/+1
Signed-off-by: Szymon Janc <szymon@janc.net.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: do not use assignment in if conditionsSzymon Janc1-2/+4
Signed-off-by: Szymon Janc <szymon@janc.net.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: include <linux/io.h> and <linux/uaccess.h> instead of <asm/io.h> ↵Szymon Janc1-2/+2
and <asm/uaccess.h> as suggested by checkpatch Signed-off-by: Szymon Janc <szymon@janc.net.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: remove unnecessary checks before kfreeSzymon Janc1-8/+5
Signed-off-by: Szymon Janc <szymon@janc.net.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29forcedeth: fix multiple code style issuesSzymon Janc1-166/+135
Signed-off-by: Szymon Janc <szymon@janc.net.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29zd1211rw: document need for kmalloc castJoe Perches1-0/+1
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29vxge: remove unnecessary [kv][mcz]alloc castsJoe Perches2-18/+10
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29qlcnic: remove unnecessary [kv][mcz]alloc castsJoe Perches1-2/+1
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29netxen: remove unnecessary [kv][mcz]alloc castsJoe Perches1-2/+1
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-28cxgb3: Removing unused return variableBreno Leitao1-2/+1
Currently the ret variable is not used for anything other than receive the value of the t3_adapter_error(), which will always be 0, because the reset parameter is 0. Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-28ethoc: remove division from loopsJonas Bonn1-4/+13
Calculating the BD entry using a modulus operation isn't optimal, especially inside the loop. This patch removes the modulus operations in favour of: i) simply checking for wrapping in the case of cur_rx ii) forcing num_tx to be a power of two and using it to mask out the entry from cur_tx The also prevents possible issues related overflow of the cur_rx and cur_tx counters. Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-28ethoc: fix function return typeJonas Bonn1-3/+2
update_ethoc_tx_stats doesn't need to return anything so make its return type void in order to avoid an unnecessary cast when the function is called. Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-28ethoc: rework mdio read/writeJonas Bonn1-8/+6
MDIO read and write were checking whether a timeout had expired to determine whether to recheck the result of the MDIO operation. Under heavy CPU usage, however, it was possible for the timeout to expire before the routine got around to be able to check a second time even, thus erroneousy returning an -EBUSY. This patch changes the the MDIO IO routines to try up to five times to complete the operation before giving up, thus lessening the dependency on CPU load. This resolves a problem whereby a ping flood would keep the CPU so busy that the above problem would manifest itself; the MDIO command to check link status would fail and the interface would erroneously be shut down. Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-28ethoc: rework interrupt handlingJonas Bonn1-27/+49
The old interrupt handling was incorrect in that it did not account for the fact that the interrupt source bits get set irregardless of whether or not their corresponding mask is set. This patch fixes that by masking off the source bits for masked interrupts. Furthermore, the handling of transmission events is moved to the NAPI polling handler alongside the reception handler, thus preventing a whole bunch of interrupts during heavy traffic. Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-28ethoc: Double check pending RX packetJonas Bonn1-2/+13
An interrupt may occur between checking bd.stat and clearing the interrupt source register which would result in the packet going totally unnoticed as the interrupt will be missed. Double check bd.stat after clearing the interrupt source register to guard against such an occurrence. Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-28ethoc: enable interrupts after napi_completeAdam Edvardsson1-1/+1
Occasionally, it seems that some race is causing the interrupts to not be reenabled otherwise with the end result that networking just stops working. Enabling interrupts after calling napi_complete is more in line with what other drivers do. Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-28ethoc: remove unused spinlockJonas Bonn1-3/+0
Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-15 20:54:53 +0300