| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
linux-can-next-for-5.10-20201007
The first 3 patches are by me and fix several warnings found
when compiling the kernel with W=1.
Lukas Bulwahn's patch adjusts the MAINTAINERS file, to accommodate
the renaming of the mcp251xfd driver.
Vincent Mailhol contributes 3 patches for the CAN networking layer.
First error queue support is added the the CAN RAW protocol.
The second patch converts the get_can_dlc() and get_canfd_dlc()
in-Kernel-only macros from using __u8 to u8.
The third patch adds a helper function to calculate the length of
one bit in in multiple of time quanta.
Oliver Hartkopp's patch add support for the ISO 15765-2:2016
transport protocol to the CAN stack.
Three patches by Lad Prabhakar add documentation for various
new rcar controllers to the device tree bindings of the rcar_can
and rcan_canfd driver.
Michael Walle's patch adds various processors to the flexcan
driver binding documentation.
The next two patches are by me and target the flexcan driver aswell.
The remove the ack_grp and ack_bit from the fsl,stop-mode DT property
and the driver, as they are not used anymore. As these are the last
two arguments this change will not break existing device trees.
The last three patches are by Srinivas Neeli and target
the xilinx_can driver.
The first one increases the lower limit for the bit rate
prescaler to 2, the other two fix sparse and coverity findings.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A subsequent addition of an IP4 or IP6 rule after other rules would
overwrite any existing TCAM entries of related L4 protocols(ex: tcp4 or
udp6). This was due to the mask including too many TCAM entries. Add new
packet type masks with bits properly excluded so rules are not overwritten.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
pointers should be casted to unsigned long to avoid
-Wpointer-to-int-cast warnings:
drivers/net/ethernet/intel/ice/ice_flow.h:197:33: warning:
cast from pointer to integer of different size
drivers/net/ethernet/intel/ice/ice_flow.h:198:32: warning:
cast to pointer from integer of different size
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While debugging a recent failure to update the flash of an ice device,
I found it helpful to add additional logging which helped determine the
root cause of the problem being a timeout issue.
Add some extra dev_dbg() logging messages which can be enabled using the
dynamic debug facility, including one for ice_aq_wait_for_event that
will use jiffies to capture a rough estimate of how long we waited for
the completion of a firmware command.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the devlink_port structure is stored within the ice_pf. This
made sense because we create a single devlink_port for each PF. This
setup does not mesh with the abstractions in the driver very well, and
led to a flow where we accidentally call devlink_port_unregister twice
during error cleanup.
In particular, if devlink_port_register or devlink_port_unregister are
called twice, this leads to a kernel panic. This appears to occur during
some possible flows while cleaning up from a failure during driver
probe.
If register_netdev fails, then we will call devlink_port_unregister in
ice_cfg_netdev as it cleans up. Later, we again call
devlink_port_unregister since we assume that we must cleanup the port
that is associated with the PF structure.
This occurs because we cleanup the devlink_port for the main PF even
though it was not allocated. We allocated the port within a per-VSI
function for managing the main netdev, but did not release the port when
cleaning up that VSI, the allocation and destruction are not aligned.
Instead of attempting to manage the devlink_port as part of the PF
structure, manage it as part of the PF VSI. Doing this has advantages,
as we can match the de-allocation of the devlink_port with the
unregister_netdev associated with the main PF VSI.
Moving the port to the VSI is preferable as it paves the way for
handling devlink ports allocated for other purposes such as SR-IOV VFs.
Since we're changing up how we allocate the devlink_port, also change
the indexing. Originally, we indexed the port using the PF id number.
This came from an old goal of sharing a devlink for each physical
function. Managing devlink instances across multiple function drivers is
not workable. Instead, lets set the port number to the logical port
number returned by firmware and set the index using the VSI index
(sometimes referred to as VSI handle).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add "fw.app.bundle_id" to display the DDP Track ID of the active DDP
package. This id is similar to "fw.bundle_id" and is a unique identifier
for the DDP package that is loaded in the device. Each new DDP has
a unique Track ID generated for it, and the ID can be used to identify
and track the DDP package.
Add documentation for the new devlink info version.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ice_info_get_dsn always returns 0, so just make it void.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A new test in checkpatch detects repeated words; cleanup all pre-existing
occurrences of those now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Co-developed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use %*phD format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the KSZ9563 3-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9563 supports both SPI (already in) and I2C. The
ksz9563 is already in the device tree binding documentation.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for devlink reload action fw_activate with reload limit
no_reset which does firmware live patching, updating the firmware image
without reset, no downtime and no configuration lose. The driver checks
if the firmware is capable of handling the pending firmware changes as a
live patch. If it is then it triggers firmware live patching flow.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Firmware live patch event notifies the driver that the firmware was just
updated using live patch. In such case the driver should not reload or
re-initiate entities, part to updating the firmware version and
re-initiate the firmware tracer which can be updated by live patch with
new strings database to help debugging an issue.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The enable_remote_dev_reset devlink param flags that the host admin
allows resets by other hosts. In case it is cleared mlx5 host PF driver
will send NACK on pci sync for firmware update reset request and the
command will fail.
By default enable_remote_dev_reset parameter is true, so pci sync for
firmware update reset is enabled.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for devlink reload action fw_activate. To activate firmware
image the mlx5 driver resets the firmware and reloads it from flash. If
a new image was stored on flash it will be loaded. Once this reload
command is executed the driver initiates fw sync reset flow, where the
firmware synchronizes all PFs on coming reset and driver reload.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If firmware sends sync_reset_abort to driver the driver should clear the
reset requested mode as reset is not expected any more.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On sync_reset_now event the driver does reload and PCI link toggle to
activate firmware upgrade reset. When the firmware sends this event it
syncs the event on all PFs, so all PFs will do PCI link toggle at once.
To do PCI link toggle, the driver ensures that no other device ID under
the same bridge by checking that all the PF functions under the same PCI
bridge have same device ID. If no other device it uses PCI bridge link
control to turn link down and up.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Once the driver gets sync_reset_request from firmware it prepares for the
coming reset and sends acknowledge.
After getting this event the driver expects device reset, either it will
trigger PCI reset on sync_reset_now event or such PCI reset will be
triggered by another PF of the same device. So it moves to reset
requested mode and if it gets PCI reset triggered by the other PF it
detect the reset and reloads.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set capability to notify the firmware that this host driver is capable
of handling pci sync for firmware update events.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add functions to query and set the MFRL reset options supported by
firmware.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add reload limit to demand restrictions on reload actions.
Reload limits supported:
no_reset: No reset allowed, no down time allowed, no link flap and no
configuration is lost.
By default reload limit is unspecified and so no constraints on reload
actions are required.
Some combinations of action and limit are invalid. For example, driver
can not reinitialize its entities without any downtime.
The no_reset reload limit will have usecase in this patchset to
implement restricted fw_activate on mlx5.
Have the uapi parameter of reload limit ready for future support of
multiselection.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add devlink reload action to allow the user to request a specific reload
action. The action parameter is optional, if not specified then devlink
driver re-init action is used (backward compatible).
Note that when required to do firmware activation some drivers may need
to reload the driver. On the other hand some drivers may need to reset
the firmware to reinitialize the driver entities. Therefore, the devlink
reload command returns the actions which were actually performed.
Reload actions supported are:
driver_reinit: driver entities re-initialization, applying devlink-param
and devlink-resource values.
fw_activate: firmware activate.
command examples:
$devlink dev reload pci/0000:82:00.0 action driver_reinit
reload_actions_performed:
driver_reinit
$devlink dev reload pci/0000:82:00.0 action fw_activate
reload_actions_performed:
driver_reinit fw_activate
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Without these definitions, the driver will crash in:
mscc_ocelot_probe
-> ocelot_init
-> ocelot_vcap_init
-> __ocelot_target_read_ix
I missed this because I did not have the VSC7514 hardware to test, only
the VSC9959 and VSC9953, and the probing part is different.
Fixes: e3aea296d86f ("net: mscc: ocelot: add definitions for VCAP ES0 keys, actions and target")
Fixes: a61e365d7c18 ("net: mscc: ocelot: add definitions for VCAP IS1 keys, actions and target")
Reported-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull vhost fixes from Michael Tsirkin:
"Some last minute vhost,vdpa fixes.
The last two of them haven't been in next but they do seem kind of
obvious, very small and safe, fix bugs reported in the field, and they
are both in a new mlx5 vdpa driver, so it's not like we can introduce
regressions"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Fix dependency on MLX5_CORE
vdpa/mlx5: should keep avail_index despite device status
vhost-vdpa: fix page pinning leakage in error path
vhost-vdpa: fix vhost_vdpa_map() on error condition
vhost: Don't call log_access_ok() when using IOTLB
vhost: Use vhost_get_used_size() in vhost_vring_set_addr()
vhost: Don't call access_ok() when using IOTLB
vhost vdpa: fix vhost_vdpa_open error handling
|
|
Pull networking fixes from Jakub Kicinski:
"One more set of fixes from the networking tree:
- add missing input validation in nl80211_del_key(), preventing
out-of-bounds access
- last minute fix / improvement of a MRP netlink (uAPI) interface
introduced in 5.9 (current) release
- fix "unresolved symbol" build error under CONFIG_NET w/o
CONFIG_INET due to missing tcp_timewait_sock and inet_timewait_sock
BTF.
- fix 32 bit sub-register bounds tracking in the bpf verifier for OR
case
- tcp: fix receive window update in tcp_add_backlog()
- openvswitch: handle DNAT tuple collision in conntrack-related code
- r8169: wait for potential PHY reset to finish after applying a FW
file, avoiding unexpected PHY behaviour and failures later on
- mscc: fix tail dropping watermarks for Ocelot switches
- avoid use-after-free in macsec code after a call to the GRO layer
- avoid use-after-free in sctp error paths
- add a device id for Cellient MPL200 WWAN card
- rxrpc fixes:
- fix the xdr encoding of the contents read from an rxrpc key
- fix a BUG() for a unsupported encoding type.
- fix missing _bh lock annotations.
- fix acceptance handling for an incoming call where the incoming
call is encrypted.
- the server token keyring isn't network namespaced - it belongs
to the server, so there's no need. Namespacing it means that
request_key() fails to find it.
- fix a leak of the server keyring"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (21 commits)
net: usb: qmi_wwan: add Cellient MPL200 card
macsec: avoid use-after-free in macsec_handle_frame()
r8169: consider that PHY reset may still be in progress after applying firmware
openvswitch: handle DNAT tuple collision
sctp: fix sctp_auth_init_hmacs() error path
bridge: Netlink interface fix.
net: wireless: nl80211: fix out-of-bounds access in nl80211_del_key()
bpf: Fix scalar32_min_max_or bounds tracking
tcp: fix receive window update in tcp_add_backlog()
net: usb: rtl8150: set random MAC address when set_ethernet_addr() fails
mptcp: more DATA FIN fixes
net: mscc: ocelot: warn when encoding an out-of-bounds watermark value
net: mscc: ocelot: divide watermark value by 60 when writing to SYS_ATOP
net: qrtr: ns: Fix the incorrect usage of rcu_read_lock()
rxrpc: Fix server keyring leak
rxrpc: The server keyring isn't network-namespaced
rxrpc: Fix accept on a connection that need securing
rxrpc: Fix some missing _bh annotations on locking conn->state_lock
rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()
rxrpc: Fix rxkad token xdr encoding
...
|
|
Remove propmt for selecting MLX5_VDPA by the user and modify
MLX5_VDPA_NET to select MLX5_VDPA. Also modify MLX5_VDPA_NET to depend
on mlx5_core.
This fixes an issue where configuration sets 'y' for MLX5_VDPA_NET while
MLX5_CORE is compiled as a module causing link errors.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 device")s
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20201007064011.GA50074@mtl-vdi-166.wap.labs.mlnx
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
A VM with mlx5 vDPA has below warnings while being reset:
vhost VQ 0 ring restore failed: -1: Resource temporarily unavailable (11)
vhost VQ 1 ring restore failed: -1: Resource temporarily unavailable (11)
We should allow userspace emulating the virtio device be
able to get to vq's avail_index, regardless of vDPA device
status. Save the index that was last seen when virtq was
stopped, so that userspace doesn't complain.
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Link: https://lore.kernel.org/r/1601583511-15138-1-git-send-email-si-wei.liu@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eli Cohen <elic@nvidia.com>
|
|
Add usb ids of the Cellient MPL200 card.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
De-referencing skb after call to gro_cells_receive() is not allowed.
We need to fetch skb->len earlier.
Fixes: 5491e7c6b1a9 ("macsec: enable GRO and RPS on macsec devices")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some firmware files trigger a PHY soft reset and don't wait for it to
be finished. PHY register writes directly after applying the firmware
may fail or provide unexpected results therefore. Fix this by waiting
for bit BMCR_RESET to be cleared after applying firmware.
There's nothing wrong with the referenced change, it's just that the
fix will apply cleanly only after this change.
Fixes: 89fbd26cca7e ("r8169: fix firmware not resetting tp->ocp_base")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull drm nouveau fixes from Dave Airlie:
"Karol found two last minute nouveau fixes, they both fix crashes, the
TTM one follows what other drivers do already, and the other is for
bailing on load on unrecognised chipsets.
- fix crash in TTM alloc fail path
- return error earlier for unknown chipsets"
* tag 'drm-fixes-2020-10-08' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/mem: guard against NULL pointer access in mem_del
drm/nouveau/device: return error for unknown chipsets
|
|
Some variables with incorrect type were passed to "of_property_read_u32"
API, "of_property_read_u32" API was expecting an "u32 *" but the formal
parameter that was passed was of type "int *". Fixed the issue by
changing the variable types from "int" to "u32" and initialized with a
default value. Fixed sparse warning.
Addresses-Coverity: "incompatible_param"
Addresses-Coverity: "UNINIT(Using uninitialized value)"
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/0651544d22f3c25893ca9d445b14823f0dfddfc8.1600073396.git.michal.simek@xilinx.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Check return value of set_reset_mode() for error.
Addresses-Coverity: "check_return"
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/bac2c2b857986472a11db341b3f6f7a8905ad0dd.1600073396.git.michal.simek@xilinx.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Bit enlarging is observed for CANFD2.0 when brp is 1,
So change brp_min value to 2.
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/bca871d7f3ca9c653d50e63c5b60028f2bdf3fb0.1600073396.git.michal.simek@xilinx.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Since commit:
048e3a34a2e7 can: flexcan: poll MCR_LPM_ACK instead of GPR ACK for stop mode acknowledgment
the driver polls the IP core's internal bit MCR[LPM_ACK] as stop mode
acknowledge and not the acknowledgment on chip level.
This means the 4th and 5th value of the property "fsl,stop-mode" isn't used
anymore. This patch removes the used "ack_gpr" and "ack_bit" from the driver.
Link: http://lore.kernel.org/r/20201006203748.1750156-15-mkl@pengutronix.de
Fixes: 048e3a34a2e7 ("can: flexcan: poll MCR_LPM_ACK instead of GPR ACK for stop mode acknowledgment")
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Rename macro CAN_CALC_SYNC_SEG to CAN_SYNC_SEG and make it available
through include/linux/can/dev.h
Add an helper function can_bit_time() which returns the duration (in
time quanta) of one CAN bit.
Rationale for this patch: the sync segment and the bit time are two
concepts which are defined in the CAN ISO standard. Device drivers for
CAN might need those.
Please refer to ISO 11898-1:2015, section 11.3.1.1 "Bit time" for
additional information.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20201002154219.4887-6-mailhol.vincent@wanadoo.fr
[mkl: Let can_bit_time() return an unsinged int, make argument const]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
other drivers seems to do something similar
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201006220528.13925-2-kherbst@redhat.com
|
|
Previously the code relied on device->pri to be NULL and to fail probing
later. We really should just return an error inside nvkm_device_ctor for
unsupported GPUs.
Fixes: 24d5ff40a732 ("drm/nouveau/device: rework mmio mapping code to get rid of second map")
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Cc: dann frazier <dann.frazier@canonical.com>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201006220528.13925-1-kherbst@redhat.com
|
|
This patch marks the arrays reg_map_c_can and reg_map_d_can as __maybe_unused,
as they are indeed unused in the c_can driver. This warning shows up, when
compiling the kernel with "W=1":
drivers/net/can/c_can/c_can.c:45:
drivers/net/can/c_can/c_can.h:124:18: warning: ‘reg_map_d_can’ defined but not used [-Wunused-const-variable=]
drivers/net/can/c_can/c_can.h:84:18: warning: ‘reg_map_c_can’ defined but not used [-Wunused-const-variable=]
Link: http://lore.kernel.org/r/20201006203748.1750156-4-mkl@pengutronix.de
Fixes: 33f810097769 ("can: c_can: Move overlay structure to array with offset as index")
Fixes: 69927fccd96b ("can: c_can: Add support for Bosch D_CAN controller")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
'if' statement
This patch fixes the following warning when building the kernel with "W=1":
warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Link: http://lore.kernel.org/r/20201006203748.1750156-3-mkl@pengutronix.de
Fixes: 03fd3cf5a179 ("can: add driver for Softing card")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull another x86 platform driver fix from Hans de Goede:
"One final pdx86 fix for Tablet Mode reporting regressions (which make
the keyboard and touchpad unusable) on various Asus notebooks.
These regressions were caused by the asus-nb-wmi and the intel-vbtn
drivers both receiving recent patches to start reporting Tablet Mode /
to report it on more models.
Due to a miscommunication between Andy and me, Andy's earlier pull-req
only contained the fix for the intel-vbtn driver and not the fix for
the asus-nb-wmi code.
This fix has been tested as a downstream patch in Fedora kernels for
approx two weeks with no problems being reported"
* tag 'platform-drivers-x86-v5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: asus-wmi: Fix SW_TABLET_MODE always reporting 1 on many different models
|
|
Pull drm fixes from Dave Airlie:
"Daniel queued these up last week and I took a long weekend so didn't
get them out, but fixing the OOB access on get font seems like
something we should land and it's cc'ed stable as well.
The other big change is a partial revert for a regression on android
on the clcd fbdev driver, and one other docs fix.
fbdev:
- Re-add FB_ARMCLCD for android
- Fix global-out-of-bounds read in fbcon_get_font()
core:
- Small doc fix"
* tag 'drm-fixes-2020-10-06-1' of git://anongit.freedesktop.org/drm/drm:
drm: drm_dsc.h: fix a kernel-doc markup
Partially revert "video: fbdev: amba-clcd: Retire elder CLCD driver"
fbcon: Fix global-out-of-bounds read in fbcon_get_font()
Fonts: Support FONT_EXTRA_WORDS macros for built-in fonts
fbdev, newport_con: Move FONT_EXTRA_WORDS macros into linux/font.h
|
|
use new helper for netstats settings
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use new helper for netstats settings
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use new helper for netstats settings
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use new helper for netstats settings
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mediadetect is another name for the EDPD (energy detect power down).
This feature allows device to save extra power when no link is available.
PHY goes into the extreme power saving mode and only periodically wakes up
and checks for the link.
AQC devices has fixed check period of 6 seconds
The feature may increase linkup time.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY downshift allows phy to try renegotiate if link is unstable
and can carry higher speed.
AQC devices has integrated PHY which is controlled by MAC firmware.
Thus, driver defines new ethtool callbacks to implement phy tunables
via netdev.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When get_registers() fails in set_ethernet_addr(),the uninitialized
value of node_id gets copied over as the address.
So, check the return value of get_registers().
If get_registers() executed successfully (i.e., it returns
sizeof(node_id)), copy over the MAC address using ether_addr_copy()
(instead of using memcpy()).
Else, if get_registers() failed instead, a randomly generated MAC
address is set as the MAC address instead.
Reported-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Tested-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
