| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As added in 3e59020abf0f ("net: bql: add __netdev_tx_sent_queue()"), which
see for performance rationale.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This just removes VLAN_TAG_PRESENT use. VLAN TCI=0 special meaning is
deeply embedded in the driver code and so is left as is.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
return -ENOMEM directly instead of assigning it in a variable
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current driver dynamically allocates an skb and maps it as DMA Rx
buffer. In order to prepare for upcoming XDP changes, let's introduce a
different allocation scheme.
Buffers are allocated dynamically and mapped into hardware.
During the Rx operation the driver uses build_skb() to produce the
necessary buffers for the network stack.
This change increases performance ~15% on 64b packets with smmu disabled
and ~5% with smmu enabled
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interferences on the SPI line could distort the response of
available buffer space. So at least we should check that the
response doesn't exceed the maximum available buffer space.
In error case increase a new error counter and retry it later.
This behavior avoids buffer errors in the QCA7000, which
results in an unnecessary chip reset including packet loss.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_l3_setup_netdev() checks if the hsuid attribute is set on the qeth
device, and propagates it to the net_device. In the past this was needed
to pick up any hsuid that was set before allocation of the net_device.
With commit d3d1b205e89f ("s390/qeth: allocate netdevice early") this
is no longer necessary, qeth_l3_dev_hsuid_store() always stores the
hsuid straight into dev->perm_addr.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the CREATE ADDR sent by qeth_l3_iqd_read_initial_mac() fails, its
callback sets a random MAC address on the net_device. The error then
propagates back, and qeth_l3_setup_netdev() bails out without
registering the net_device.
Any subsequent call to qeth_l3_setup_netdev() will then attempt a fresh
CREATE ADDR which either 1) also fails, or 2) sets a proper MAC address
on the net_device. Consequently, the net_device will never be registered
with a random MAC and we can drop the fallback code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_l3_send_ipa_arp_cmd() is merely a wrapper around
qeth_send_control_data() now. So push the length adjustment into
QETH_SETASS_BASE_LEN, and remove the wrapper. While at it, also remove
some redundant 0-initializations.
qeth_send_setassparms() requires that callers prepare their command
parameters, so that they can be copied into the parameter area in one
go. Skip the indirection, and just let callers set up the command
themselves.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call qeth_prepare_ipa_cmd() during setup of a new IPA cmd buffer, so
that it is used for all commands. Thus ARP and SNMP requests don't have
to do their own initialization.
This will now also set the proper MPC protocol version for SNMP requests
on L2 devices.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-implement the card-by-RDEV lookup by using device model concepts, and
remove the now redundant list of all qeth card instances in the system.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 82bf5c0867f6 ("s390/qeth: add support for IPv6 TSO"),
qeth_xmit() also knows how to build TSO packets and is practically
identical to qeth_l3_xmit().
Convert qeth_l3_xmit() into a thin wrapper that merely strips the
L2 header off a packet, and calls qeth_xmit() for the actual
TX processing.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Filling the HW header from one single function will make it easier to
rip out all the duplicated transmit code in qeth_l3_xmit(). On top, this
saves one conditional branch in the TSO path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default, READ MAC on a Layer2 OSD device returns the adapter's
burnt-in MAC address. Given the default scenario of many virtual devices
on the same adapter, qeth can't make any use of this address and
therefore skips the READ MAC call for this device type.
But in some configurations, the READ MAC command for a Layer2 OSD device
actually returns a pre-provisioned, virtual MAC address. So enable the
READ MAC code to detect this situation, and let the L2 subdriver
call READ MAC for OSD devices.
This also removes the QETH_LAYER2_MAC_READ flag, which protects L2
devices against calling READ MAC multiple times. Instead protect the
whole call to qeth_l2_request_initial_mac().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
draft-ietf-nvo3-geneve-08 says:
It is strongly RECOMMENDED that Path MTU Discovery ([RFC1191],
[RFC1981]) be used by setting the DF bit in the IP header when Geneve
packets are transmitted over IPv4 (this is the default with IPv6).
Now that ICMP error handling is working for GENEVE, we can comply with
this recommendation.
Make this configurable, though, to avoid breaking existing setups. By
default, DF won't be set. It can be set or inherited from inner IPv4
packets. If it's configured to be inherited and we are encapsulating IPv6,
it will be set.
This only applies to non-lwt tunnels: if an external control plane is
used, tunnel key will still control the DF flag.
v2:
- DF behaviour configuration only applies for non-lwt tunnels, apply DF
setting only if (!geneve->collect_md) in geneve_xmit_skb()
(Stephen Hemminger)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Export an encap_err_lookup() operation to match an ICMP error against a
valid VNI.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow users to set the IPv4 DF bit in outgoing packets, or to inherit its
value from the IPv4 inner header. If the encapsulated protocol is IPv6 and
DF is configured to be inherited, always set it.
For IPv4, inheriting DF from the inner header was probably intended from
the very beginning judging by the comment to vxlan_xmit(), but it wasn't
actually implemented -- also because it would have done more harm than
good, without handling for ICMP Fragmentation Needed messages.
According to RFC 7348, "Path MTU discovery MAY be used". An expired RFC
draft, draft-saum-nvo3-pmtud-over-vxlan-05, whose purpose was to describe
PMTUD implementation, says that "is a MUST that Vxlan gateways [...]
SHOULD set the DF-bit [...]", whatever that means.
Given this background, the only sane option is probably to let the user
decide, and keep the current behaviour as default.
This only applies to non-lwt tunnels: if an external control plane is
used, tunnel key will still control the DF flag.
v2:
- DF behaviour configuration only applies for non-lwt tunnels, move DF
setting to if (!info) block in vxlan_xmit_one() (Stephen Hemminger)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Export an encap_err_lookup() operation to match an ICMP error against a
valid VNI.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in dev_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/broadcom/genet/bcmgenet.c: In function 'bcmgenet_power_down':
drivers/net/ethernet/broadcom/genet/bcmgenet.c:1136:6: warning:
variable 'ret' set but not used [-Wunused-but-set-variable]
bcmgenet_power_down should return 'ret' instead of 0.
Fixes: ca8cf341903f ("net: bcmgenet: propagate errors from bcmgenet_power_down")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use phy_check_link_status in more places in the state machine.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the recent changes in the state machine state PHY_AN isn't used
any longer and can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In few places in the state machine the state is set to PHY_RUNNING or
PHY_NOLINK after doing a phy_read_status(). So factor this out to
phy_check_link_status().
First use it in phy_start_aneg(): By setting the state to PHY_RUNNING
or PHY_NOLINK directly we can remove the code to handle the case that
we're using interrupts and aneg was finished already.
Definition of phy_link_up and phy_link_down needs to be moved because
they are called in the new function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If aneg isn't finished yet then the PHY reports the link as down.
There's no benefit in setting the state to PHY_AN because the next
state machine run would set the status to PHY_NOLINK anyway (except
in the meantime aneg has been finished and link is up). Therefore
we can set the state to PHY_RUNNING or PHY_NOLINK directly.
In addition change the do_carrier parameter in phy_link_down() to true.
If carrier was marked as up before (what should never be the case because
PHY was in state PHY_HALTED before) then we should mark it as down now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If aneg is enabled and the PHY reports the link as up then definitely
aneg finished successfully. Therefore this check is useless and
can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-11-07
This series contains updates to almost all of the Intel wired LAN
drivers.
Lance Roy replaces a spin lock with lockdep_assert_held() for igbvf
driver in move toward trying to remove spin_is_locked().
Colin Ian King fixes a potential null pointer dereference by adding a
check in ixgbe. Also fixed the igc driver by properly assigning the
return error code of a function call, so that we can properly check it.
Shannon Nelson updates the ixgbe driver to not block IPsec offload when
in VEPA mode, in VEB mode, IPsec offload is still blocked because the
device drops packets into a black hole.
Jake adds support for software timestamping for packets sent over
ixgbevf. Also modifies i40e, iavf, igb, igc, and ixgbe to delay calling
skb_tx_timestamp() to the latest point possible, which is just prior to
notifying the hardware of the new Tx packet.
Todd adds the new WoL filter flag so that we properly report that we do
not support this new feature.
YueHaibing from Huawei fixes the igc driver by cleaning up variables
that are not "really" used.
Dan Carpenter cleans up igc whitespace issues.
Miroslav Lichvar fixes e1000e for potential underflow issue in the
timecounter, so modify the driver to use timecounter_cyc2time() to allow
non-monotonic SYSTIM readings.
Sasha provides additional igc cleanups based on community feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Offload of geneve decap rules is supported in NFP. Include geneve in the
check for supported types.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the recently added VXLAN and geneve helper functions to
determine the type of the netdev from its rtnl_link_ops.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Expose the MUM/SUC Firmware, UEFI Expansion ROM and MC Status partitions
of the NIC's NVRAM as MTDs if found on the NIC. The first two are needed
in order to properly update them when performing firmware updates; the MC
Status partition is used to determine whether a signed firmware image was
accepted or rejected by a Secure NIC.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tun XDP sendmsg code path, unconditionally computes the symmetric
hash of each packet for RFS's sake, even when we could skip it. e.g.
when the device has a single queue.
This change adds the check already in-place for the skb sendmsg path
to avoid unneeded hashing.
The above gives small, but measurable, performance gain for VM xmit
path when zerocopy is not enabled.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add byte queue limits support in the fsl_ucc_hdlc driver.
Signed-off-by: Mathias Thore <mathias.thore@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of listing every single PHYID, load the driver for every PHYID
with a Realtek OUI, independent of model number and revision.
This patch also improves two further aspects:
- constify realtek_tbl[]
- the mask should have been 0xffffffff instead of 0x001fffff so far,
by masking out some bits a PHY from another vendor could have been
matched
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_trigger_machine() is used in phy.c only, so we can make it static.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/dsa/bcm_sf2_cfp.c:1168:2-3: Unneeded semicolon
drivers/net/dsa/bcm_sf2_cfp.c:532:2-3: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Fixes: ae7a5aff783c ("net: dsa: bcm_sf2: Keep copy of inserted rules")
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for BCM7255 EPHY.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb for packets that are multicast or to a link-local address are
not marked as being enslaved to a VRF, if they are received on a socket
bound to the VRF. This is needed for ND and it is preferable for the
kernel not to have to deal with the additional use-cases if ll or mcast
packets are handled as enslaved. However, this does not allow service
instances listening on unbound and bound to VRF sockets to distinguish
the VRF used, if packets are sent as multicast or to a link-local
address. The fix is for the VRF driver to also mark these skb as being
enslaved to the VRF.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c: In function 'hclge_log_and_clear_ppp_error':
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c:821:24: warning:
variable 'reset_level' set but not used [-Wunused-but-set-variable]
enum hnae3_reset_type reset_level = HNAE3_NONE_RESET;
It never used since introduction in commit
01865a50d78f ("net: hns3: Add enable and process hw errors of TM scheduler")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use driver's common notifier for LAG and tunnel configuration.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code interested in networking events registers its own notifier
handlers. Create one device-wide notifier instance.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nfp_fl_lag_changels_event() never fails, and therefore we would
never return NOTIFY_BAD for NETDEV_CHANGELOWERSTATE. Make this
clearer by changing nfp_fl_lag_changels_event()'s return type
to void.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Returning an error from a notifier means we want to veto the change.
We shouldn't veto NETDEV_UNREGISTER just because we couldn't find
the tracking info for given master.
I can't seem to find a way to trigger this unless we have some
other bug, so it's probably not fix-worthy.
While at it move the checking if the netdev really is of interest
into the handling functions, like we do for other events.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For flower tunnel offloads FW has to be informed about MAC addresses
of tunnel devices. We use a netdev notifier to keep track of these
addresses.
Remove unnecessary loop over netdevices after notifier is registered.
The intention of the loop was to catch devices which already existed
on the system before nfp driver got loaded, but netdev notifier will
replay NETDEV_REGISTER events.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ipv6 set flow label and hop limit action offload. Since pedit sets
headers per 4 byte word, we need to ensure that setting either version,
priority, payload_len or nexthdr does not get offloaded.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ipv4 set ttl and tos action offload. Since pedit sets headers per 4
byte word, we need to ensure that setting either version, ihl, protocol,
total length or checksum does not get offloaded.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is not necessary to reallocate the descriptor and remap the
descriptor memory in reset process, otherwise it may cause memory
not freed problem.
Also, this patch initializes the cmd queue's spinlocks in
hclgevf_alloc_cmd_queue, and take the spinlocks when reinitializing
cmd queue' registers.
Fixes: fedd0c15d288 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When hclge_reset() is called, it may fail for several reasons.
For example, an higher-level reset event occurs, memory allocation
failure, hardware reset timeout, etc. Therefore, it is necessary
to add corresponding error handling for these situations.
1. A high-level reset is required due to a high-level reset failure.
2. For memory allocation failure, a high-level reset is initiated by
the timer to recover. The reason for using the timer is to prevent this
new high-level reset to interrupt the reset process of other pf/vf;
3. For the case of hardware reset timeout, reschedule the reset task
to wait for the hardware to complete the reset.
For memory allocation failure and reset timeouts, in order to prevent
an infinite number of scheduled reset tasks, the number of error
recovery needs to be limited.
This patch also add some reset related debug log printing.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While doing resetting, roce should do its uninitailization part
before nic's, and do its initialization part after nic's.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing PF reset, the driver needs to do some preparatory work
before asserting PF reset. Since when hardware is resetting, it
is necessary to stop tx/rx queue, clear hardware table, etc,
otherwise hardware may run into unrecoverable state if there is
still IO running when the hardware is resetting.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
