| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 3b2ac810d86eb96e882db80a3320a3848b133208 upstream.
svc_i3c_master_do_daa() {
...
for (i = 0; i < dev_nb; i++) {
ret = i3c_master_add_i3c_dev_locked(m, addrs[i]);
if (ret)
goto rpm_out;
}
}
If two devices (A and B) are detected in DAA and address 0xa is assigned to
device A and 0xb to device B, a failure in i3c_master_add_i3c_dev_locked()
for device A (addr: 0xa) could prevent device B (addr: 0xb) from being
registered on the bus. The I3C stack might still consider 0xb a free
address. If a subsequent Hotjoin occurs, 0xb might be assigned to Device A,
causing both devices A and B to use the same address 0xb, violating the I3C
specification.
The return value for i3c_master_add_i3c_dev_locked() should not be checked
because subsequent steps will scan the entire I3C bus, independent of
whether i3c_master_add_i3c_dev_locked() returns success.
If device A registration fails, there is still a chance to register device
B. i3c_master_add_i3c_dev_locked() can reset DAA if a failure occurs while
retrieving device information.
Cc: stable@kernel.org
Fixes: 317bacf960a4 ("i3c: master: add enable(disable) hot join in sys entry")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241002-svc-i3c-hj-v6-6-7e6e1d3569ae@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 36faa04ce3d9c962b4b29d285ad07ca29e2988e4 upstream.
When a new device hotjoins, a new dynamic address is assigned.
i3c_master_add_i3c_dev_locked() identifies that the device was previously
attached to the bus and locates the olddev.
i3c_master_add_i3c_dev_locked()
{
...
olddev = i3c_master_search_i3c_dev_duplicate(newdev);
...
if (olddev) {
...
i3c_dev_disable_ibi_locked(olddev);
^^^^^^
The olddev should not receive any commands on the i3c bus as it
does not exist and has been assigned a new address. This will
result in NACK or timeout. So remove it.
}
i3c_dev_free_ibi_locked(olddev);
^^^^^^^^
This function internally calls i3c_dev_disable_ibi_locked() function
causing to send DISEC command with old Address.
The olddev should not receive any commands on the i3c bus as it
does not exist and has been assigned a new address. This will
result in NACK or timeout. So, update the olddev->ibi->enabled
flag to false to avoid DISEC with OldAddr.
}
Include part of Ravindra Yashvant Shinde's work:
https://lore.kernel.org/linux-i3c/20240820151917.3904956-1-ravindra.yashvant.shinde@nxp.com/T/#u
Fixes: 317bacf960a4 ("i3c: master: add enable(disable) hot join in sys entry")
Co-developed-by: Ravindra Yashvant Shinde <ravindra.yashvant.shinde@nxp.com>
Signed-off-by: Ravindra Yashvant Shinde <ravindra.yashvant.shinde@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241001162232.223724-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b5a23a60e8ab5711f4952912424347bf3864ce8d upstream.
When CONFIG_DMA_ENGINE is disabled, the driver now fails to build:
drivers/tty/serial/amba-pl011.c: In function 'pl011_unthrottle_rx':
drivers/tty/serial/amba-pl011.c:1822:16: error: 'struct uart_amba_port' has no member named 'using_rx_dma'
1822 | if (uap->using_rx_dma) {
| ^~
drivers/tty/serial/amba-pl011.c:1823:20: error: 'struct uart_amba_port' has no member named 'dmacr'
1823 | uap->dmacr |= UART011_RXDMAE;
| ^~
drivers/tty/serial/amba-pl011.c:1824:32: error: 'struct uart_amba_port' has no member named 'dmacr'
1824 | pl011_write(uap->dmacr, uap, REG_DMACR);
| ^~
Add the missing #ifdef check around these field accesses, matching
what other parts of this driver do.
Fixes: 2bcacc1c87ac ("serial: amba-pl011: Fix RX stall when DMA is used")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202411140617.nkjeHhsK-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241115110021.744332-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b012170fed282151f7ba8988a347670c299f5ab3 upstream.
When support for vivobook fan profiles was added, the initial
call to throttle_thermal_policy_set_default() was removed, which
however is necessary for full initialization.
Fix this by calling throttle_thermal_policy_set_default() again
when setting up the platform profile.
Fixes: bcbfcebda2cb ("platform/x86: asus-wmi: add support for vivobook fan profiles")
Reported-by: Michael Larabel <Michael@phoronix.com>
Closes: https://www.phoronix.com/review/lunar-lake-xe2/5
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20241025191514.15032-2-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f2e0eee4703869dc5edb5302a919861566ca7797 upstream.
The DWC3_EP_RESOURCE_ALLOCATED flag ensures that the resource of an
endpoint is only assigned once. Unless the endpoint is reset, don't
clear this flag. Otherwise we may set endpoint resource again, which
prevents the driver from initiate transfer after handling a STALL or
endpoint halt to the control endpoint.
Cc: stable@vger.kernel.org
Fixes: b311048c174d ("usb: dwc3: gadget: Rewrite endpoint allocation flow")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/00122b7cc5be06abef461776e7cc9f5ebc8bc1cb.1713229786.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 73dae652dcac776296890da215ee7dec357a1032 upstream.
Split resume into a 3rd step to handle displays when DCC is
enabled on DCN 4.0.1. Move display after the buffer funcs
have been re-enabled so that the GPU will do the move and
properly set the DCC metadata for DCN.
v2: fix fence irq resume ordering
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.11.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef5f5e7b6f73f79538892a8be3a3bee2342acc9f upstream.
When multiple ODR switch happens during FIFO off, the change could
not be taken into account if you get back to previous FIFO on value.
For example, if you run sensor buffer at 50Hz, stop, change to
200Hz, then back to 50Hz and restart buffer, data will be timestamped
at 200Hz. This due to testing against mult and not new_mult.
To prevent this, let's just run apply_odr automatically when FIFO is
off. It will also simplify driver code.
Update inv_mpu6050 and inv_icm42600 to delete now useless apply_odr.
Fixes: 95444b9eeb8c ("iio: invensense: fix odr switching to same value")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://patch.msgid.link/20241021-invn-inv-sensors-timestamp-fix-switch-fifo-off-v2-1-39ffd43edcc4@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9044ad57b60b0556d42b6f8aa218a68865e810a4 upstream.
Don't flush all pending DbC data requests when an endpoint halts.
An endpoint may halt and xHC DbC triggers a STALL error event if there's
an issue with a bulk data transfer. The transfer should restart once xHC
DbC receives a ClearFeature(ENDPOINT_HALT) request from the host.
Once xHC DbC restarts it will start from the TRB pointed to by dequeue
field in the endpoint context, which might be the same TRB we got the
STALL event for. Turn the TRB to a no-op in this case to make sure xHC
DbC doesn't reuse and tries to retransmit this same TRB after we already
handled it, and gave its corresponding data request back.
Other STALL events might be completely bogus.
Lukasz Bartosik discovered that xHC DbC might issue spurious STALL events
if hosts sends a ClearFeature(ENDPOINT_HALT) request to non-halted
endpoints even without any active bulk transfers.
Assume STALL event is spurious if it reports 0 bytes transferred, and
the endpoint stopped on the STALLED TRB.
Don't give back the data request corresponding to the TRB in this case.
The halted status is per endpoint. Track it with a per endpoint flag
instead of the driver invented DbC wide DS_STALLED state.
DbC remains in DbC-Configured state even if endpoints halt. There is no
Stalled state in the DbC Port state Machine (xhci section 7.6.6)
Reported-by: Łukasz Bartosik <ukaszb@chromium.org>
Closes: https://lore.kernel.org/linux-usb/20240725074857.623299-1-ukaszb@chromium.org/
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9c7c5430bca36e9636eabbba0b3b53251479c7ab ]
Align the page tracking maximum message size with the device's
capability instead of relying on PAGE_SIZE.
This adjustment resolves a mismatch on systems where PAGE_SIZE is 64K,
but the firmware only supports a maximum message size of 4K.
Now that we rely on the device's capability for max_message_size, we
must account for potential future increases in its value.
Key considerations include:
- Supporting message sizes that exceed a single system page (e.g., an 8K
message on a 4K system).
- Ensuring the RQ size is adjusted to accommodate at least 4
WQEs/messages, in line with the device specification.
The above has been addressed as part of the patch.
Fixes: 79c3cf279926 ("vfio/mlx5: Init QP based resources for dirty tracking")
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Yingshun Cui <yicui@redhat.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20241205122654.235619-1-yishaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 52fd1709e41d3a85b48bcfe2404a024ebaf30c3b ]
With the new __counted_by annotation in clk_hw_onecell_data, the "num"
struct member must be set before accessing the "hws" array. Failing to
do so will trigger a runtime warning when enabling CONFIG_UBSAN_BOUNDS
and CONFIG_FORTIFY_SOURCE.
Fixes: f316cdff8d67 ("clk: Annotate struct clk_hw_onecell_data with __counted_by")
Signed-off-by: Haoyu Li <lihaoyu499@gmail.com>
Link: https://lore.kernel.org/r/20241203142915.345523-1-lihaoyu499@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cad4dda82c7eedcfc22597267e710ccbcf39d572 ]
SG2044 relys on an internal divisor when calculating bitrate, which
means a wrong clock for the most common bitrates. So add a quirk for
this uart device to skip the set rate call and only relys on the
internal UART divisor.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Link: https://lore.kernel.org/r/20241024062105.782330-4-inochiama@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0a6efab33eab4e973db26d9f90c3e97a7a82e399 ]
On my device reading entirety of /sys/devices/pnp0/00:03/cmos_nvram0/nvmem
takes about 9 msec during which time interrupts are off on the CPU that
does the read and the thread that performs the read can not be migrated
or preempted by another higher priority thread (RT or not).
Allow readers and writers be preempted by taking and releasing rtc_lock
spinlock for each individual byte read or written rather than once per
read/write request.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Link: https://lore.kernel.org/r/Zxv8QWR21AV4ztC5@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7738a7ab9d12c5371ed97114ee2132d4512e9fd5 ]
Add a quirk similar to eeprom_93xx46 to add an extra clock cycle before
reading data from the EEPROM.
The 93Cx6 family of EEPROMs output a "dummy 0 bit" between the writing
of the op-code/address from the host to the EEPROM and the reading of
the actual data from the EEPROM.
More info can be found on page 6 of the AT93C46 datasheet (linked below).
Similar notes are found in other 93xx6 datasheets.
In summary the read operation for a 93Cx6 EEPROM is:
Write to EEPROM: 110[A5-A0] (9 bits)
Read from EEPROM: 0[D15-D0] (17 bits)
Where:
110 is the start bit and READ OpCode
[A5-A0] is the address to read from
0 is a "dummy bit" preceding the actual data
[D15-D0] is the actual data.
Looking at the READ timing diagrams in the 93Cx6 datasheets the dummy
bit should be clocked out on the last address bit clock cycle meaning it
should be discarded naturally.
However, depending on the hardware configuration sometimes this dummy
bit is not discarded. This is the case with Exar PCI UARTs which require
an extra clock cycle between sending the address and reading the data.
Datasheet: https://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-5193-SEEPROM-AT93C46D-Datasheet.pdf
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/0f23973efefccd2544705a0480b4ad4c2353e407.1727880931.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 928cd772e18ffbd7723cb2361db4a8ccf2222235 ]
It is not necessarily corrupted. When there is RAS fatal error, device
memory access is blocked. Hence vcpu bo cannot be saved to system memory
as in a regular suspend sequence before going for reset. In other full
device reset cases, that gets saved and restored during resume.
v2: Remove redundant code like vcn_v4_0 did
v2: Refine commit message
v3: Drop the volatile
v3: Refine commit message
Signed-off-by: Xiang Liu <xiang.liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Stanley.Yang <Stanley.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c26acb09ccbef47d1fddaf0783c1392d0462122c ]
It has been found that the (non-vendor issued) ACPI ID for Lite-On
LTR303 is present in Microsoft catalog. Add it to the list of the
supported devices.
Link: https://www.catalog.update.microsoft.com/Search.aspx?q=lter0303
Closes: https://lore.kernel.org/r/9cdda3e0-d56e-466f-911f-96ffd6f602c8@redhat.com
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241024191200.229894-24-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 548f48b66c0c5d4b9795a55f304b7298cde2a025 ]
As per USBSTS register description about UEI:
When completion of a USB transaction results in an error condition, this
bit is set by the Host/Device Controller. This bit is set along with the
USBINT bit, if the TD on which the error interrupt occurred also had its
interrupt on complete (IOC) bit set.
UI is set only when IOC set. Add checking UEI to fix miss call
isr_tr_complete_handler() when IOC have not set and transfer error happen.
Acked-by: Peter Chen <peter.chen@kernel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240926022906.473319-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd8aa15848f5f21951cd0b0d01510b3ad1f777d4 ]
The Asus entries in the acpi_quirk_skip_dmi_ids[] table are the only
entries without a comment which model they apply to. Add these comments.
The Asus TF103C entry also is in the wrong place for what is supposed to
be an alphabetically sorted list. Move it up so that the list is properly
sorted and add a comment that the list is alphabetically sorted.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241116095825.11660-2-hdegoede@redhat.com
[ rjw: Changelog and subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 82f250ed1a1dcde0ad2a1513f85af7f9514635e8 ]
The Acer Iconia One 8 A1-840 (not to be confused with the A1-840FHD which
is a different model) ships with Android 4.4 as factory OS and has the
usual broken DSDT issues for x86 Android tablets.
Add quirks to skip ACPI I2C client enumeration and disable ACPI battery/AC
and ACPI GPIO event handlers.
Also add the "INT33F5" HID for the TI PMIC used on this tablet to the list
of HIDs for which not to skip i2c_client instantiation, since we do want
an ACPI instantiated i2c_client for the PMIC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241116095825.11660-1-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
avoid deadlock
[ Upstream commit 6cf7b65f7029914dc0cd7db86fac9ee5159008c6 ]
A deadlock may happen since the i3c_master_register() acquires
&i3cbus->lock twice. See the log below.
Use i3cdev->desc->info instead of calling i3c_device_info() to
avoid acquiring the lock twice.
v2:
- Modified the title and commit message
============================================
WARNING: possible recursive locking detected
6.11.0-mainline
--------------------------------------------
init/1 is trying to acquire lock:
f1ffff80a6a40dc0 (&i3cbus->lock){++++}-{3:3}, at: i3c_bus_normaluse_lock
but task is already holding lock:
f1ffff80a6a40dc0 (&i3cbus->lock){++++}-{3:3}, at: i3c_master_register
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&i3cbus->lock);
lock(&i3cbus->lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by init/1:
#0: fcffff809b6798f8 (&dev->mutex){....}-{3:3}, at: __driver_attach
#1: f1ffff80a6a40dc0 (&i3cbus->lock){++++}-{3:3}, at: i3c_master_register
stack backtrace:
CPU: 6 UID: 0 PID: 1 Comm: init
Call trace:
dump_backtrace+0xfc/0x17c
show_stack+0x18/0x28
dump_stack_lvl+0x40/0xc0
dump_stack+0x18/0x24
print_deadlock_bug+0x388/0x390
__lock_acquire+0x18bc/0x32ec
lock_acquire+0x134/0x2b0
down_read+0x50/0x19c
i3c_bus_normaluse_lock+0x14/0x24
i3c_device_get_info+0x24/0x58
i3c_device_uevent+0x34/0xa4
dev_uevent+0x310/0x384
kobject_uevent_env+0x244/0x414
kobject_uevent+0x14/0x20
device_add+0x278/0x460
device_register+0x20/0x34
i3c_master_register_new_i3c_devs+0x78/0x154
i3c_master_register+0x6a0/0x6d4
mtk_i3c_master_probe+0x3b8/0x4d8
platform_probe+0xa0/0xe0
really_probe+0x114/0x454
__driver_probe_device+0xa0/0x15c
driver_probe_device+0x3c/0x1ac
__driver_attach+0xc4/0x1f0
bus_for_each_dev+0x104/0x160
driver_attach+0x24/0x34
bus_add_driver+0x14c/0x294
driver_register+0x68/0x104
__platform_driver_register+0x20/0x30
init_module+0x20/0xfe4
do_one_initcall+0x184/0x464
do_init_module+0x58/0x1ec
load_module+0xefc/0x10c8
__arm64_sys_finit_module+0x238/0x33c
invoke_syscall+0x58/0x10c
el0_svc_common+0xa8/0xdc
do_el0_svc+0x1c/0x28
el0_svc+0x50/0xac
el0t_64_sync_handler+0x70/0xbc
el0t_64_sync+0x1a8/0x1ac
Signed-off-by: Defa Li <defa.li@mediatek.com>
Link: https://lore.kernel.org/r/20241107132549.25439-1-defa.li@mediatek.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aa46a3736afcb7b0793766d22479b8b99fc1b322 ]
Wangxun FF5xxx NICs are similar to SFxxx, RP1000 and RP2000 NICs. They may
be multi-function devices, but they do not advertise an ACS capability.
But the hardware does isolate FF5xxx functions as though it had an ACS
capability and PCI_ACS_RR and PCI_ACS_CR were set in the ACS Control
register, i.e., all peer-to-peer traffic is directed upstream instead of
being routed internally.
Add ACS quirk for FF5xxx NICs in pci_quirk_wangxun_nic_acs() so the
functions can be in independent IOMMU groups.
Link: https://lore.kernel.org/r/E16053DB2B80E9A5+20241115024604.30493-1-mengyuanlou@net-swift.com
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2fa046449a82a7d0f6d9721dd83e348816038444 ]
The "bus" and "cxl_bus" reset methods reset a device by asserting Secondary
Bus Reset on the bridge leading to the device. These only work if the
device is the only device below the bridge.
Add a sysfs 'reset_subordinate' attribute on bridges that can assert
Secondary Bus Reset regardless of how many devices are below the bridge.
This resets all the devices below a bridge in a single command, including
the locking and config space save/restore that reset methods normally do.
This may be the only way to reset devices that don't support other reset
methods (ACPI, FLR, PM reset, etc).
Link: https://lore.kernel.org/r/20241025222755.3756162-1-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
[bhelgaas: commit log, add capable(CAP_SYS_ADMIN) check]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3b96b895127b7c0aed63d82c974b46340e8466c1 ]
Some computers with CPUs that lack Thunderbolt features use discrete
Thunderbolt chips to add Thunderbolt functionality. These Thunderbolt
chips are located within the chassis; between the Root Port labeled
ExternalFacingPort and the USB-C port.
These Thunderbolt PCIe devices should be labeled as fixed and trusted, as
they are built into the computer. Otherwise, security policies that rely on
those flags may have unintended results, such as preventing USB-C ports
from enumerating.
Detect the above scenario through the process of elimination.
1) Integrated Thunderbolt host controllers already have Thunderbolt
implemented, so anything outside their external facing Root Port is
removable and untrusted.
Detect them using the following properties:
- Most integrated host controllers have the "usb4-host-interface"
ACPI property, as described here:
https://learn.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#mapping-native-protocols-pcie-displayport-tunneled-through-usb4-to-usb4-host-routers
- Integrated Thunderbolt PCIe Root Ports before Alder Lake do not
have the "usb4-host-interface" ACPI property. Identify those by
their PCI IDs instead.
2) If a Root Port does not have integrated Thunderbolt capabilities, but
has the "ExternalFacingPort" ACPI property, that means the
manufacturer has opted to use a discrete Thunderbolt host controller
that is built into the computer.
This host controller can be identified by virtue of being located
directly below an external-facing Root Port that lacks integrated
Thunderbolt. Label it as trusted and fixed.
Everything downstream from it is untrusted and removable.
The "ExternalFacingPort" ACPI property is described here:
https://learn.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#identifying-externally-exposed-pcie-root-ports
Link: https://lore.kernel.org/r/20240910-trust-tbt-fix-v5-1-7a7a42a5f496@chromium.org
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Esther Shimanovich <eshimanovich@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d66041063192497a4a97d21dbf86b79a03a7f4fb ]
The remapped PCIe Root Port and the child device have PM L1 Substates
capability, but they are disabled originally.
Here is a failed example on ASUS B1400CEAE:
Capabilities: [900 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1- L1_PM_Substates+
PortCommonModeRestoreTime=32us PortTPowerOnTime=10us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=101376ns
L1SubCtl2: T_PwrOn=50us
Enable PCI-PM L1 PM Substates for devices below VMD while they are in D0
(see PCIe r6.0, sec 5.5.4).
Link: https://lore.kernel.org/r/20241001083438.10070-4-jhp@endlessos.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218394
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b727484cace4be22be9321cc0bc9487648ba447b ]
Add support for this VMD device which supports the bus restriction mode.
The feature that turns off vector 0 for MSI-X remapping is also enabled.
Link: https://lore.kernel.org/r/20241011175657.249948-1-nirmal.patel@linux.intel.com
Signed-off-by: Nirmal Patel <nirmal.patel@linux.ntel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a63b74f2e35be3829f256922037ae5cee6bb844a ]
Add the new IPQ9574 platform which is based on the Qcom IP rev. 1.27.0
and Synopsys IP rev. 5.80a.
The platform itself has four PCIe Gen3 controllers: two single-lane and
two dual-lane, all are based on Synopsys IP rev. 5.70a. As such, reuse
all the members of 'ops_2_9_0'.
Link: https://lore.kernel.org/r/20240801054803.3015572-5-quic_srichara@quicinc.com
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6ca2738174e4ee44edb2ab2d86ce74f015a0cc32 ]
Bus cleanup path in DMA mode may trigger a RING_OP_STAT interrupt when
the ring is being stopped. Depending on timing between ring stop request
completion, interrupt handler removal and code execution this may lead
to a NULL pointer dereference in hci_dma_irq_handler() if it gets to run
after the io_data pointer is set to NULL in hci_dma_cleanup().
Prevent this my masking the ring interrupts before ring stop request.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20240920144432.62370-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b61352101470f8b68c98af674e187cfaa7c43504 ]
When nd_dax is NULL, nd_pfn is consequently NULL as well. Nevertheless,
it is inadvisable to perform pointer arithmetic or address-taking on a
NULL pointer.
Introduce the nd_dax_devinit() function to enhance the code's logic and
improve its readability.
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://patch.msgid.link/20241108085526.527957-1-yiyang13@huawei.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e2ffb6c3a40ee714160e35e61f0a984028b5d550 ]
Add support for tsens v1.4 block what can be found in
MSM8937 and MSM8917.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/r/20241113-msm8917-v6-5-c348fb599fef@mainlining.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f755261190e88f5d19fe0a3b762f0bbaff6bd438 ]
The PM8937 provides 4 MPPs.
Add a compatible to support them.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/20241031-msm8917-v2-4-8a075faa89b1@mainlining.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 89265a58ff24e3885c2c9ca722bc3aaa47018be9 ]
PM8937 has 8 GPIO-s with holes on GPIO3, GPIO4 and GPIO6.
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/20241031-msm8917-v2-2-8a075faa89b1@mainlining.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0b120edb37dc9dd8ca82893d386922eb6b16f860 ]
Most drives rewind the tape when the device is reset. Reading and writing
are not allowed until something is done to make the tape position match the
user's expectation (e.g., rewind the tape). Add MTIOCGET and MTLOAD to
operations allowed after reset. MTIOCGET is modified to not touch the tape
if pos_unknown is non-zero. The tape location is known after MTLOAD.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219419#c14
Link: https://lore.kernel.org/r/20241106095723.63254-3-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5bb2d6179d1a8039236237e1e94cfbda3be1ed9e ]
Struct mtget field mt_blkno -1 means it is unknown. Don't add anything to
it.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219419#c14
Link: https://lore.kernel.org/r/20241106095723.63254-2-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ca7cd938725a4050dcd62ae9472e931d603118d ]
There is NULL pointer issue observed if from Process A where hid device
being added which results in adding a led_cdev addition and later a
another call to access of led_cdev attribute from Process B can result
in NULL pointer issue.
Use mutex led_cdev->led_access to protect access to led->cdev and its
attribute inside brightness_show() and max_brightness_show() and also
update the comment for mutex that it should be used to protect the led
class device fields.
Process A Process B
kthread+0x114
worker_thread+0x244
process_scheduled_works+0x248
uhid_device_add_worker+0x24
hid_add_device+0x120
device_add+0x268
bus_probe_device+0x94
device_initial_probe+0x14
__device_attach+0xfc
bus_for_each_drv+0x10c
__device_attach_driver+0x14c
driver_probe_device+0x3c
__driver_probe_device+0xa0
really_probe+0x190
hid_device_probe+0x130
ps_probe+0x990
ps_led_register+0x94
devm_led_classdev_register_ext+0x58
led_classdev_register_ext+0x1f8
device_create_with_groups+0x48
device_create_groups_vargs+0xc8
device_add+0x244
kobject_uevent+0x14
kobject_uevent_env[jt]+0x224
mutex_unlock[jt]+0xc4
__mutex_unlock_slowpath+0xd4
wake_up_q+0x70
try_to_wake_up[jt]+0x48c
preempt_schedule_common+0x28
__schedule+0x628
__switch_to+0x174
el0t_64_sync+0x1a8/0x1ac
el0t_64_sync_handler+0x68/0xbc
el0_svc+0x38/0x68
do_el0_svc+0x1c/0x28
el0_svc_common+0x80/0xe0
invoke_syscall+0x58/0x114
__arm64_sys_read+0x1c/0x2c
ksys_read+0x78/0xe8
vfs_read+0x1e0/0x2c8
kernfs_fop_read_iter+0x68/0x1b4
seq_read_iter+0x158/0x4ec
kernfs_seq_show+0x44/0x54
sysfs_kf_seq_show+0xb4/0x130
dev_attr_show+0x38/0x74
brightness_show+0x20/0x4c
dualshock4_led_get_brightness+0xc/0x74
[ 3313.874295][ T4013] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000060
[ 3313.874301][ T4013] Mem abort info:
[ 3313.874303][ T4013] ESR = 0x0000000096000006
[ 3313.874305][ T4013] EC = 0x25: DABT (current EL), IL = 32 bits
[ 3313.874307][ T4013] SET = 0, FnV = 0
[ 3313.874309][ T4013] EA = 0, S1PTW = 0
[ 3313.874311][ T4013] FSC = 0x06: level 2 translation fault
[ 3313.874313][ T4013] Data abort info:
[ 3313.874314][ T4013] ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000
[ 3313.874316][ T4013] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 3313.874318][ T4013] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 3313.874320][ T4013] user pgtable: 4k pages, 39-bit VAs, pgdp=00000008f2b0a000
..
[ 3313.874332][ T4013] Dumping ftrace buffer:
[ 3313.874334][ T4013] (ftrace buffer empty)
..
..
[ dd3313.874639][ T4013] CPU: 6 PID: 4013 Comm: InputReader
[ 3313.874648][ T4013] pc : dualshock4_led_get_brightness+0xc/0x74
[ 3313.874653][ T4013] lr : led_update_brightness+0x38/0x60
[ 3313.874656][ T4013] sp : ffffffc0b910bbd0
..
..
[ 3313.874685][ T4013] Call trace:
[ 3313.874687][ T4013] dualshock4_led_get_brightness+0xc/0x74
[ 3313.874690][ T4013] brightness_show+0x20/0x4c
[ 3313.874692][ T4013] dev_attr_show+0x38/0x74
[ 3313.874696][ T4013] sysfs_kf_seq_show+0xb4/0x130
[ 3313.874700][ T4013] kernfs_seq_show+0x44/0x54
[ 3313.874703][ T4013] seq_read_iter+0x158/0x4ec
[ 3313.874705][ T4013] kernfs_fop_read_iter+0x68/0x1b4
[ 3313.874708][ T4013] vfs_read+0x1e0/0x2c8
[ 3313.874711][ T4013] ksys_read+0x78/0xe8
[ 3313.874714][ T4013] __arm64_sys_read+0x1c/0x2c
[ 3313.874718][ T4013] invoke_syscall+0x58/0x114
[ 3313.874721][ T4013] el0_svc_common+0x80/0xe0
[ 3313.874724][ T4013] do_el0_svc+0x1c/0x28
[ 3313.874727][ T4013] el0_svc+0x38/0x68
[ 3313.874730][ T4013] el0t_64_sync_handler+0x68/0xbc
[ 3313.874732][ T4013] el0t_64_sync+0x1a8/0x1ac
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reviewed-by: Anish Kumar <yesanishhere@gmail.com>
Link: https://lore.kernel.org/r/20241103160527.82487-1-quic_mojha@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d2e0a043530b9d6f37a8de8f05e0725667aba0a6 ]
The SAR2130P platform has the same TCSR Clock Controller as the SM8550,
except for the lack of the UFS clocks. Extend the SM8550 TCSRCC driver
to support SAR2130P.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241027-sar2130p-clocks-v5-9-ecad2a1432ba@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2cc88de6261f01ebd4e2a3b4e29681fe87d0c089 ]
Define clocks as supported by the RPMh on the SAR2130P platform. The
msm-5.10 kernel declares just the CXO clock, the RF_CLK1 clock was added
following recommendation from Taniya Das.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20241027-sar2130p-clocks-v5-7-ecad2a1432ba@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aec8c0e28ce4a1f89fd82fcc06a5cc73147e9817 ]
Generally SDCC clocks use clk_rcg2_floor_ops, however on SAR2130P
platform it's recommended to use rcg2_shared_ops for all Root Clock
Generators to park them instead of disabling. Implement a mix of those,
clk_rcg2_shared_floor_ops.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241027-sar2130p-clocks-v5-6-ecad2a1432ba@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d35f7672715d1ff3e3ad9bb4ae6ac6cb484200fe ]
During initialization, the driver allocates wq->pring in lpfc_wq_create
and lpfc_sli4_queue_unset() is the only place where kfree(wq->pring) is
called.
There is a possible memory leak in lpfc_sli_brdrestart_s4() (restart)
and lpfc_pci_remove_one_s4() (rmmod) paths because there are no calls to
lpfc_sli4_queue_unset() to kfree() the wq->pring.
Fix by inserting a call to lpfc_sli4_queue_unset() in
lpfc_sli_brdrestart_s4() and lpfc_sli4_hba_unset() routines. Also, add
a check for the SLI_ACTIVE flag before issuing the Q_DESTROY mailbox
command. If not set, then the mailbox command will obviously fail. In
such cases, skip issuing the mailbox command and only execute the driver
resource clean up portions of the lpfc_*q_destroy routines.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20241031223219.152342-4-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 78bc671bd1501e2f6c571e063301a4fdc5db53b2 ]
Replace UFSHCD_QUIRK_BROKEN_64BIT_ADDRESS with
ufs_hba_variant_ops::set_dma_mask. Update the Renesas driver
accordingly. This patch enables supporting other configurations than
32-bit or 64-bit DMA addresses, e.g. 36-bit DMA addresses.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241018194753.775074-1-bvanassche@acm.org
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5a3e85c3c397c781393ea5fb2f45b1f60f8a4e6e ]
When two client of the same gpio call pinctrl_select_state() for the
same functionality, we are seeing NULL pointer issue while accessing
desc->mux_owner.
Let's say two processes A, B executing in pin_request() for the same pin
and process A updates the desc->mux_usecount but not yet updated the
desc->mux_owner while process B see the desc->mux_usecount which got
updated by A path and further executes strcmp and while accessing
desc->mux_owner it crashes with NULL pointer.
Serialize the access to mux related setting with a mutex lock.
cpu0 (process A) cpu1(process B)
pinctrl_select_state() { pinctrl_select_state() {
pin_request() { pin_request() {
...
....
} else {
desc->mux_usecount++;
desc->mux_usecount && strcmp(desc->mux_owner, owner)) {
if (desc->mux_usecount > 1)
return 0;
desc->mux_owner = owner;
} }
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/20241014192930.1539673-1-quic_mojha@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2233c4a0b948211743659b24c13d6bd059fa75fc ]
For no forced preemption model kernel, in the scenario where the
expander is connected to 12 high performance SAS SSDs, the following
call trace may occur:
[ 214.409199][ C240] watchdog: BUG: soft lockup - CPU#240 stuck for 22s! [irq/149-hisi_sa:3211]
[ 214.568533][ C240] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--)
[ 214.575224][ C240] pc : fput_many+0x8c/0xdc
[ 214.579480][ C240] lr : fput+0x1c/0xf0
[ 214.583302][ C240] sp : ffff80002de2b900
[ 214.587298][ C240] x29: ffff80002de2b900 x28: ffff1082aa412000
[ 214.593291][ C240] x27: ffff3062a0348c08 x26: ffff80003a9f6000
[ 214.599284][ C240] x25: ffff1062bbac5c40 x24: 0000000000001000
[ 214.605277][ C240] x23: 000000000000000a x22: 0000000000000001
[ 214.611270][ C240] x21: 0000000000001000 x20: 0000000000000000
[ 214.617262][ C240] x19: ffff3062a41ae580 x18: 0000000000010000
[ 214.623255][ C240] x17: 0000000000000001 x16: ffffdb3a6efe5fc0
[ 214.629248][ C240] x15: ffffffffffffffff x14: 0000000003ffffff
[ 214.635241][ C240] x13: 000000000000ffff x12: 000000000000029c
[ 214.641234][ C240] x11: 0000000000000006 x10: ffff80003a9f7fd0
[ 214.647226][ C240] x9 : ffffdb3a6f0482fc x8 : 0000000000000001
[ 214.653219][ C240] x7 : 0000000000000002 x6 : 0000000000000080
[ 214.659212][ C240] x5 : ffff55480ee9b000 x4 : fffffde7f94c6554
[ 214.665205][ C240] x3 : 0000000000000002 x2 : 0000000000000020
[ 214.671198][ C240] x1 : 0000000000000021 x0 : ffff3062a41ae5b8
[ 214.677191][ C240] Call trace:
[ 214.680320][ C240] fput_many+0x8c/0xdc
[ 214.684230][ C240] fput+0x1c/0xf0
[ 214.687707][ C240] aio_complete_rw+0xd8/0x1fc
[ 214.692225][ C240] blkdev_bio_end_io+0x98/0x140
[ 214.696917][ C240] bio_endio+0x160/0x1bc
[ 214.701001][ C240] blk_update_request+0x1c8/0x3bc
[ 214.705867][ C240] scsi_end_request+0x3c/0x1f0
[ 214.710471][ C240] scsi_io_completion+0x7c/0x1a0
[ 214.715249][ C240] scsi_finish_command+0x104/0x140
[ 214.720200][ C240] scsi_softirq_done+0x90/0x180
[ 214.724892][ C240] blk_mq_complete_request+0x5c/0x70
[ 214.730016][ C240] scsi_mq_done+0x48/0xac
[ 214.734194][ C240] sas_scsi_task_done+0xbc/0x16c [libsas]
[ 214.739758][ C240] slot_complete_v3_hw+0x260/0x760 [hisi_sas_v3_hw]
[ 214.746185][ C240] cq_thread_v3_hw+0xbc/0x190 [hisi_sas_v3_hw]
[ 214.752179][ C240] irq_thread_fn+0x34/0xa4
[ 214.756435][ C240] irq_thread+0xc4/0x130
[ 214.760520][ C240] kthread+0x108/0x13c
[ 214.764430][ C240] ret_from_fork+0x10/0x18
This is because in the hisi_sas driver, both the hardware interrupt
handler and the interrupt thread are executed on the same CPU. In the
performance test scenario, function irq_wait_for_interrupt() will always
return 0 if lots of interrupts occurs and the CPU will be continuously
consumed. As a result, the CPU cannot run the watchdog thread. When the
watchdog time exceeds the specified time, call trace occurs.
To fix it, add cond_resched() to execute the watchdog thread.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20241008021822.2617339-8-liyihang9@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 58414a31c5713afb5449fd74a26a843d34cc62e8 ]
When PINCTRL_IMX_SCU was selected by PINCTRL_IMX8DXL or PINCTRL_IMX8QM
combined with COMPILE_TEST on a non-arm platforms, the IMX_SCU
dependency could not be enabled.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410031439.GyTSa0kX-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202410030852.q0Hukplf-lkp@intel.com/
Signed-off-by: Esben Haabendal <esben@geanix.com>
Link: https://lore.kernel.org/20241003-imx-pinctrl-compile-test-fix-v1-1-145ca1948cc3@geanix.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e64285ff41bb7a934bd815bd38f31119be62ac37 ]
Since '1 << rocker_port->pport' may be undefined for port >= 32,
cast the left operand to 'unsigned long long' like it's done in
'rocker_port_set_enable()' above. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://patch.msgid.link/20241114151946.519047-1-dmantipov@yandex.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 677a55ba11a82c2835550a82324cec5fcb2f9e2d ]
This adds quirks for broken ats2851 features.
Signed-off-by: Danil Pylaev <danstiv404@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 69b84ffce260ff13826dc10aeb3c3e5c2288a552 ]
Add the support ID 0489:e123 to usb_device_id table for
Realtek RTL8852B chip.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 7 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e123 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 078e0d596f7b5952dad8662ace8f20ed2165e2ce ]
qca8k_phy_eth_command() is used to probe the child MDIO bus while the
parent MDIO is locked. This causes lockdep splat, reporting a possible
deadlock. It is not an actually deadlock, because different locks are
used. By making use of mutex_lock_nested() we can avoid this false
positive.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241110175955.3053664-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
brcmf_sdiod_sglist_rw()
[ Upstream commit 857282b819cbaa0675aaab1e7542e2c0579f52d7 ]
This patch fixes a NULL pointer dereference bug in brcmfmac that occurs
when a high 'sd_sgentry_align' value applies (e.g. 512) and a lot of queued SKBs
are sent from the pkt queue.
The problem is the number of entries in the pre-allocated sgtable, it is
nents = max(rxglom_size, txglom_size) + max(rxglom_size, txglom_size) >> 4 + 1.
Given the default [rt]xglom_size=32 it's actually 35 which is too small.
Worst case, the pkt queue can end up with 64 SKBs. This occurs when a new SKB
is added for each original SKB if tailroom isn't enough to hold tail_pad.
At least one sg entry is needed for each SKB. So, eventually the "skb_queue_walk loop"
in brcmf_sdiod_sglist_rw may run out of sg entries. This makes sg_next return
NULL and this causes the oops.
The patch sets nents to max(rxglom_size, txglom_size) * 2 to be able handle
the worst-case.
Btw. this requires only 64-35=29 * 16 (or 20 if CONFIG_NEED_SG_DMA_LENGTH) = 464
additional bytes of memory.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241107132903.13513-1-nvbolhuis@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4fa4f049dc0d9741b16c96bcbf0108c85368a2b9 ]
This patch fixes incorrect code alignment.
./drivers/net/wireless/intel/ipw2x00/libipw_rx.c:871:2-3: code aligned with following code on line 882.
./drivers/net/wireless/intel/ipw2x00/libipw_rx.c:886:2-3: code aligned with following code on line 900.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=11381
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241101060725.54640-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e2e97435783979124ba92d6870415c57ecfef6a5 ]
The driver needs to set the correct max_segment_size;
otherwise debug_dma_map_sg() will complain about the
over-mapping of the AMDGPU sg length as following:
WARNING: CPU: 6 PID: 1964 at kernel/dma/debug.c:1178 debug_dma_map_sg+0x2dc/0x370
[ 364.049444] Modules linked in: veth amdgpu(OE) amdxcp drm_exec gpu_sched drm_buddy drm_ttm_helper ttm(OE) drm_suballoc_helper drm_display_helper drm_kms_helper i2c_algo_bit rpcsec_gss_krb5 auth_rpcgss nfsv4 nfs lockd grace netfs xt_conntrack xt_MASQUERADE nf_conntrack_netlink xfrm_user xfrm_algo iptable_nat xt_addrtype iptable_filter br_netfilter nvme_fabrics overlay nfnetlink_cttimeout nfnetlink openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c bridge stp llc amd_atl intel_rapl_msr intel_rapl_common sunrpc sch_fq_codel snd_hda_codec_realtek snd_hda_codec_generic snd_hda_scodec_component snd_hda_codec_hdmi snd_hda_intel snd_intel_dspcfg edac_mce_amd binfmt_misc snd_hda_codec snd_pci_acp6x snd_hda_core snd_acp_config snd_hwdep snd_soc_acpi kvm_amd snd_pcm kvm snd_seq_midi snd_seq_midi_event crct10dif_pclmul ghash_clmulni_intel sha512_ssse3 snd_rawmidi sha256_ssse3 sha1_ssse3 aesni_intel snd_seq nls_iso8859_1 crypto_simd snd_seq_device cryptd snd_timer rapl input_leds snd
[ 364.049532] ipmi_devintf wmi_bmof ccp serio_raw k10temp sp5100_tco soundcore ipmi_msghandler cm32181 industrialio mac_hid msr parport_pc ppdev lp parport drm efi_pstore ip_tables x_tables pci_stub crc32_pclmul nvme ahci libahci i2c_piix4 r8169 nvme_core i2c_designware_pci realtek i2c_ccgx_ucsi video wmi hid_generic cdc_ether usbnet usbhid hid r8152 mii
[ 364.049576] CPU: 6 PID: 1964 Comm: rocminfo Tainted: G OE 6.10.0-custom #492
[ 364.049579] Hardware name: AMD Majolica-RN/Majolica-RN, BIOS RMJ1009A 06/13/2021
[ 364.049582] RIP: 0010:debug_dma_map_sg+0x2dc/0x370
[ 364.049585] Code: 89 4d b8 e8 36 b1 86 00 8b 4d b8 48 8b 55 b0 44 8b 45 a8 4c 8b 4d a0 48 89 c6 48 c7 c7 00 4b 74 bc 4c 89 4d b8 e8 b4 73 f3 ff <0f> 0b 4c 8b 4d b8 8b 15 c8 2c b8 01 85 d2 0f 85 ee fd ff ff 8b 05
[ 364.049588] RSP: 0018:ffff9ca600b57ac0 EFLAGS: 00010286
[ 364.049590] RAX: 0000000000000000 RBX: ffff88b7c132b0c8 RCX: 0000000000000027
[ 364.049592] RDX: ffff88bb0f521688 RSI: 0000000000000001 RDI: ffff88bb0f521680
[ 364.049594] RBP: ffff9ca600b57b20 R08: 000000000000006f R09: ffff9ca600b57930
[ 364.049596] R10: ffff9ca600b57928 R11: ffffffffbcb46328 R12: 0000000000000000
[ 364.049597] R13: 0000000000000001 R14: ffff88b7c19c0700 R15: ffff88b7c9059800
[ 364.049599] FS: 00007fb2d3516e80(0000) GS:ffff88bb0f500000(0000) knlGS:0000000000000000
[ 364.049601] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 364.049603] CR2: 000055610bd03598 CR3: 00000001049f6000 CR4: 0000000000350ef0
[ 364.049605] Call Trace:
[ 364.049607] <TASK>
[ 364.049609] ? show_regs+0x6d/0x80
[ 364.049614] ? __warn+0x8c/0x140
[ 364.049618] ? debug_dma_map_sg+0x2dc/0x370
[ 364.049621] ? report_bug+0x193/0x1a0
[ 364.049627] ? handle_bug+0x46/0x80
[ 364.049631] ? exc_invalid_op+0x1d/0x80
[ 364.049635] ? asm_exc_invalid_op+0x1f/0x30
[ 364.049642] ? debug_dma_map_sg+0x2dc/0x370
[ 364.049647] __dma_map_sg_attrs+0x90/0xe0
[ 364.049651] dma_map_sgtable+0x25/0x40
[ 364.049654] amdgpu_bo_move+0x59a/0x850 [amdgpu]
[ 364.049935] ? srso_return_thunk+0x5/0x5f
[ 364.049939] ? amdgpu_ttm_tt_populate+0x5d/0xc0 [amdgpu]
[ 364.050095] ttm_bo_handle_move_mem+0xc3/0x180 [ttm]
[ 364.050103] ttm_bo_validate+0xc1/0x160 [ttm]
[ 364.050108] ? amdgpu_ttm_tt_get_user_pages+0xe5/0x1b0 [amdgpu]
[ 364.050263] amdgpu_amdkfd_gpuvm_alloc_memory_of_gpu+0xa12/0xc90 [amdgpu]
[ 364.050473] kfd_ioctl_alloc_memory_of_gpu+0x16b/0x3b0 [amdgpu]
[ 364.050680] kfd_ioctl+0x3c2/0x530 [amdgpu]
[ 364.050866] ? __pfx_kfd_ioctl_alloc_memory_of_gpu+0x10/0x10 [amdgpu]
[ 364.051054] ? srso_return_thunk+0x5/0x5f
[ 364.051057] ? tomoyo_file_ioctl+0x20/0x30
[ 364.051063] __x64_sys_ioctl+0x9c/0xd0
[ 364.051068] x64_sys_call+0x1219/0x20d0
[ 364.051073] do_syscall_64+0x51/0x120
[ 364.051077] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 364.051081] RIP: 0033:0x7fb2d2f1a94f
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6aacd1484468361d1d04badfe75f264fa5314864 ]
When the frag just got a page, then may lead to regression on VM.
Specially if the sysctl net.core.high_order_alloc_disable value is 1,
then the frag always get a page when do refill.
Which could see reliable crashes or scp failure (scp a file 100M in size
to VM).
The issue is that the virtnet_rq_dma takes up 16 bytes at the beginning
of a new frag. When the frag size is larger than PAGE_SIZE,
everything is fine. However, if the frag is only one page and the
total size of the buffer and virtnet_rq_dma is larger than one page, an
overflow may occur.
The commit f9dac92ba908 ("virtio_ring: enable premapped mode whatever
use_dma_api") introduced this problem. And we reverted some commits to
fix this in last linux version. Now we try to enable it and fix this
bug directly.
Here, when the frag size is not enough, we reduce the buffer len to fix
this problem.
Reported-by: "Si-Wei Liu" <si-wei.liu@oracle.com>
Tested-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit afe260df55ac280cd56306248cb6d8a6b0db095c ]
Under sriov, host driver will save and restore vf pci cfg space during
reset. And during device init, under sriov, pci_restore_state happens after
fullaccess released, and it can have race condition with mmio protection
enable from host side leading to missing interrupts.
So skip amdgpu_device_cache_pci_state for sriov.
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Acked-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
