| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is the usual set of changes for device trees, with over 700
non-merged changesets. There is an ongoing set of dtc warning fixes
and the usual bugfixes, cleanups and added device support.
The most interesting bit as usual is support for new machines listed
below:
- The Allwinner H6 makes its debut with the Pine-H64 board, and we
get two new machines based on its older siblings: the H5 based
OrangePi Zero+ and the A64 based Teres-I Laptop from Olimex. On the
32-bit side, we add The Olimex som204 based on Allwinner A20, and
the Banana Pi M2 Zero development board (based on H2).
- NVIDIA adds support for Tegra194 aka "Xavier", plus their p2972
development board and p2888 CPU module.
- The Nuvoton npcm750 is a BMC that was newly added, for now we only
support running on the evaluation board.
- STmicroelectronics stm32 gains support for the stm32mp157c and two
evaluation boards.
- The Toradex Colibri board family grows a few members based on the
i.MX6ULL variant.
- The Advantec DMS-BA16 is a Qseven module using the NXP i.MX6 family
of chips.
- The Phytec phyBOARD Mira is a family of industrial boards based on
i.MX6. For now, four models get added.
- TI am335x based PDU-001 is an industrial embedded machine used for
traffic monitoring
- The Aspeed platform now supports running on the BMC on the Qualcomm
Centriq 2400 server
- Samsung Exynos4 based Galaxy S3 is a family of mobile phones
Qualcomm msm8974 based Galaxy S5 is a rather different phone made
by the same company.
- The Xilinx Zynq and ZynqMP platforms now gained a lot of dts file
for the various boards made by Xilinx themselves, as well as the
Digilent Zybo Z7.
- The ARM Versatile family now supports the "IB2" interface board.
- The Renesas H2 based "Stout" and the H3 based Salvator-X are more
evaluation boards named after a kind of beer, as most of them are.
The r8a77980 (V3H) based "Condor" apparently doesn't follow that
tradition. ;-)
- ROC-RK3328-CC is a simple developement board from the Libre
Computer Project, based on the Rockchips RK3328 SoC
- Haiku is another development board plus Qseven module based on
Rockchips RK3368 and made by Theobroma Systems"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (701 commits)
arm: dts: modify Nuvoton NPCM7xx device tree structure
arm: dts: modify Makefile NPCM750 configuration name
arm: dts: modify clock binding in NPCM750 device tree
arm: dts: modify timer register size in NPCM750 device tree
arm: dts: modify UART compatible name in NPCM750 device tree
arm: dts: add watchdog device to NPCM750 device tree
arm64: dts: uniphier: add ethernet node for PXs3
ARM: dts: uniphier: add pinctrl groups of ethernet for second instance
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for board using GPL-2.0+
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0+/MIT
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0
arm: dts: armada-385-turris-omnia: use SPDX-License-Identifier
arm: dts: armada-385-db-ap: use SPDX-License-Identifier
arm: dts: armada-388-rd: use SPDX-License-Identifier
arm: dts: armada-xp-db-xc3-24g4xg: use SPDX-License-Identifier
arm: dts: armada-xp-db-dxbc2: use SPDX-License-Identifier
arm: dts: armada-370-db: use SPDX-License-Identifier
arm: dts: armada-*.dts: use SPDX-License-Identifier for most of the Armada based board
arm: dts: armada-xp-98dx: use SPDX-License-Identifier for prestara 98d SoCs
arm: dts: armada-*.dtsi: use SPDX-License-Identifier for most of the Armada SoCs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- Sync dtc to upstream version v1.4.6-9-gaadd0b65c987. This adds a
bunch more warnings (hidden behind W=1).
- Build dtc lexer and parser files instead of using shipped versions.
- Rework overlay apply API to take an FDT as input and apply overlays
in a single step.
- Add a phandle lookup cache. This improves boot time by hundreds of
msec on systems with large DT.
- Add trivial mcp4017/18/19 potentiometers bindings.
- Remove VLA stack usage in DT code.
* tag 'devicetree-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (26 commits)
of: unittest: fix an error code in of_unittest_apply_overlay()
of: unittest: move misplaced function declaration
of: unittest: Remove VLA stack usage
of: overlay: Fix forgotten reference to of_overlay_apply()
of: Documentation: Fix forgotten reference to of_overlay_apply()
of: unittest: local return value variable related cleanups
of: unittest: remove unneeded local return value variables
dt-bindings: trivial: add various mcp4017/18/19 potentiometers
of: unittest: fix an error test in of_unittest_overlay_8()
of: cache phandle nodes to reduce cost of of_find_node_by_phandle()
dt-bindings: rockchip-dw-mshc: use consistent clock names
MAINTAINERS: Add linux/of_*.h headers to appropriate subsystems
scripts: turn off some new dtc warnings by default
scripts/dtc: Update to upstream version v1.4.6-9-gaadd0b65c987
scripts/dtc: generate lexer and parser during build instead of shipping
powerpc: boot: add strrchr function
of: overlay: do not include path in full_name of added nodes
of: unittest: clean up changeset test
arm64/efi: Make strrchr() available to the EFI namespace
ARM: boot: add strrchr function
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: arcmsr, qla2xx, lpfc,
ufs, mpt3sas, hisi_sas.
In addition we have removed several really old drivers: sym53c416,
NCR53c406a, fdomain, fdomain_cs and removed the old scsi_module.c
initialization from all remaining drivers.
Plus an assortment of bug fixes, initialization errors and other minor
fixes"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (168 commits)
scsi: ufs: Add support for Auto-Hibernate Idle Timer
scsi: ufs: sysfs: reworking of the rpm_lvl and spm_lvl entries
scsi: qla2xxx: fx00 copypaste typo
scsi: qla2xxx: fix error message on <qla2400
scsi: smartpqi: update driver version
scsi: smartpqi: workaround fw bug for oq deletion
scsi: arcmsr: Change driver version to v1.40.00.05-20180309
scsi: arcmsr: Sleep to avoid CPU stuck too long for waiting adapter ready
scsi: arcmsr: Handle adapter removed due to thunderbolt cable disconnection.
scsi: arcmsr: Rename ACB_F_BUS_HANG_ON to ACB_F_ADAPTER_REMOVED for adapter hot-plug
scsi: qla2xxx: Update driver version to 10.00.00.06-k
scsi: qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan
scsi: qla2xxx: Cleanup code to improve FC-NVMe error handling
scsi: qla2xxx: Fix FC-NVMe IO abort during driver reset
scsi: qla2xxx: Fix retry for PRLI RJT with reason of BUSY
scsi: qla2xxx: Remove nvme_done_list
scsi: qla2xxx: Return busy if rport going away
scsi: qla2xxx: Fix n2n_ae flag to prevent dev_loss on PDB change
scsi: qla2xxx: Add FC-NVMe abort processing
scsi: qla2xxx: Add changes for devloss timeout in driver
...
|
|
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
|
|
Pull EDAC updates from Borislav Petkov:
"Noteworthy is the NVDIMM support:
- NVDIMM support to EDAC (Tony Luck)
- misc fixes"
* tag 'edac_for_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, sb_edac: Remove variable length array usage
EDAC, skx_edac: Detect non-volatile DIMMs
firmware, DMI: Add function to look up a handle and return DIMM size
acpi, nfit: Add function to look up nvdimm device and provide SMBIOS handle
EDAC: Add new memory type for non-volatile DIMMs
EDAC: Drop duplicated array of strings for memory type names
EDAC, layerscape: Allow building for LS1021A
|
|
In the effort to remove all VLAs from the kernel[1], it is desirable to
build with -Wvla. However, this warning is overly pessimistic, in that
it is only happy with stack array sizes that are declared as constant
expressions, and not constant values. One case of this is the
evaluation of the max() macro which, due to its construction, ends up
converting constant expression arguments into a constant value result.
All attempts to rewrite this macro with __builtin_constant_p() failed
with older compilers (e.g. gcc 4.4)[2]. However, Martin Uecker,
constructed[3] a mind-shattering solution that works everywhere.
Cthulhu fhtagn!
This patch updates the min()/max() macros to evaluate to a constant
expression when called on constant expression arguments. This removes
several false-positive stack VLA warnings from an x86 allmodconfig build
when -Wvla is added:
$ diff -u before.txt after.txt | grep ^-
-drivers/input/touchscreen/cyttsp4_core.c:871:2: warning: ISO C90 forbids variable length array ‘ids’ [-Wvla]
-fs/btrfs/tree-checker.c:344:4: warning: ISO C90 forbids variable length array ‘namebuf’ [-Wvla]
-lib/vsprintf.c:747:2: warning: ISO C90 forbids variable length array ‘sym’ [-Wvla]
-net/ipv4/proc.c:403:2: warning: ISO C90 forbids variable length array ‘buff’ [-Wvla]
-net/ipv6/proc.c:198:2: warning: ISO C90 forbids variable length array ‘buff’ [-Wvla]
-net/ipv6/proc.c:218:2: warning: ISO C90 forbids variable length array ‘buff64’ [-Wvla]
This also updates two cases where different enums were being compared
and explicitly casts them to int (which matches the old side-effect of
the single-evaluation code): one in tpm/tpm_tis_core.h, and one in
drm/drm_color_mgmt.c.
[1] https://lkml.org/lkml/2018/3/7/621
[2] https://lkml.org/lkml/2018/3/10/170
[3] https://lkml.org/lkml/2018/3/20/845
Co-Developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Co-Developed-by: Martin Uecker <Martin.Uecker@med.uni-goettingen.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- new driver for PhoenixRC Flight Controller Adapter
- new driver for RAVE SP Power button
- fixes for autosuspend-related deadlocks in a few unput USB dirvers
- support for 2nd wheel in ATech PS/2 mouse
- fix for ALPS trackpoint detection on Thinkpad L570 and Latitude 7370
- bunch of cleanups in various in PS/2 protocols
- other assorted changes and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: i8042 - enable MUX on Sony VAIO VGN-CS series to fix touchpad
Input: stmfts, s6sy761 - update my e-mail
Input: stmfts - use async probe & suspend/resume to avoid 2s delay
Input: ALPS - fix TrackStick detection on Thinkpad L570 and Latitude 7370
Input: xpad - add PDP device id 0x02a4
Input: alps - report pressure of v3 and v7 trackstick
Input: pxrc - new driver for PhoenixRC Flight Controller Adapter
Input: usbtouchscreen - do not rely on input_dev->users
Input: usbtouchscreen - fix deadlock in autosuspend
Input: pegasus_notetaker - do not rely on input_dev->users
Input: pagasus_notetaker - fix deadlock in autosuspend
Input: synaptics_usb - do not rely on input_dev->users
Input: synaptics_usb - fix deadlock in autosuspend
Input: gpio-keys - add support for wakeup event action
Input: appletouch - use true and false for boolean values
Input: silead - add Chuwi Hi8 support
Input: analog - use get_cycles() on PPC
Input: stmpe-keypad - remove VLA usage
Input: i8042 - add Lenovo ThinkPad L460 to i8042 reset list
Input: add RAVE SP Powerbutton driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
kfifo: fix inaccurate comment
tools/thermal: tmon: fix for segfault
net: Spelling s/stucture/structure/
edd: don't spam log if no EDD information is present
Documentation: Fix early-microcode.txt references after file rename
tracing: Block comments should align the * on each line
treewide: Fix typos in printk
GenWQE: Fix a typo in two comments
treewide: Align function definition open/close braces
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- 3rd generation Wacom Intuos BT device support from Aaron Armstrong
Skomra
- support for NSG-MR5U and NSG-MR7U devices from Todd Kelner
- multitouch Razer Blade Stealth support from Benjamin Tissoires
- Elantech touchpad support from Alexandrov Stansilav
- a few other scattered-around fixes and cleanups to drivers and
generic code
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (31 commits)
HID: google: Enable PM Full On mode when adjusting backlight
HID: google: add google hammer HID driver
HID: core: reset the quirks before calling probe again
HID: multitouch: do not set HID_QUIRK_NO_INIT_REPORTS
HID: core: remove the need for HID_QUIRK_NO_EMPTY_INPUT
HID: use BIT() macro for quirks too
HID: use BIT macro instead of plain integers for flags
HID: multitouch: remove dead zones of Razer Blade Stealth
HID: multitouch: export a quirk for the button handling of touchpads
HID: usbhid: extend the polling interval configuration to keyboards
HID: ntrig: document sysfs interface
HID: wacom: wacom_wac_collection() is local to wacom_wac.c
HID: wacom: generic: add the "Report Valid" usage
HID: wacom: generic: Support multiple tools per report
HID: wacom: Add support for 3rd generation Intuos BT
HID: core: rewrite the hid-generic automatic unbind
HID: sony: Add touchpad support for NSG-MR5U and NSG-MR7U remotes
HID: hid-multitouch: Use true and false for boolean values
HID: hid-ntrig: use true and false for boolean values
HID: logitech-hidpp: document sysfs interface
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became a large update. The changes are scattered widely, and the
majority of them are attributed to ASoC componentization. The gitk
output made me dizzy, but it's slightly better than London tube.
OK, below are some highlights:
- Continued hardening works in ALSA PCM core; most of the existing
syzkaller reports should have been covered.
- USB-audio got the initial USB Audio Class 3 support, as well as
UAC2 jack detection support and more DSD-device support.
- ASoC componentization: finally each individual driver was converted
to components framework, which is more future-proof for further
works. Most of conversations were systematic.
- Lots of fixes for Intel Baytrail / Cherrytrail devices with Realtek
codecs, typically tablets and small PCs.
- Fixes / cleanups for Samsung Odroid systems
- Cleanups in Freescale SSI driver
- New ASoC drivers:
* AKM AK4458 and AK5558 codecs
* A few AMD based machine drivers
* Intel Kabylake machine drivers
* Maxim MAX9759 codec
* Motorola CPCAP codec
* Socionext Uniphier SoCs
* TI PCM1789 and TDA7419 codecs
- Retirement of Blackfin drivers along with architecture removal"
* tag 'sound-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (497 commits)
ALSA: pcm: Fix UAF at PCM release via PCM timer access
ALSA: usb-audio: silence a static checker warning
ASoC: tscs42xx: Remove owner assignment from i2c_driver
ASoC: mediatek: remove "simple-mfd" in the example
ASoC: cpcap: replace codec to component
ASoC: Intel: bytcr_rt5651: don't use codec anymore
ASoC: amd: don't use codec anymore
ALSA: usb-audio: fix memory leak on cval
ALSA: pcm: Fix mutex unbalance in OSS emulation ioctls
ASoC: topology: Fix kcontrol name string handling
ALSA: aloop: Mark paused device as inactive
ALSA: usb-audio: update clock valid control
ALSA: usb-audio: UAC2 jack detection
ALSA: pcm: Return -EBUSY for OSS ioctls changing busy streams
ALSA: pcm: Avoid potential races between OSS ioctls and read/write
ALSA: usb-audio: Integrate native DSD support for ITF-USB based DACs.
ALSA: usb-audio: FIX native DSD support for TEAC UD-501 DAC
ALSA: usb-audio: Add native DSD support for Luxman DA-06
ALSA: usb-audio: fix uac control query argument
ASoC: nau8824: recover system clock when device changes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of depending on
it. This is merged with the same pattern for all the ISA drivers
and some other Kconfig cleanups related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of this SoC
from the ARM tree.
- Move the documentation over to driver-api to conform with the rest
of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
want to get rid of.
- Managed to remove VLA allocation from two drivers pending more
fixes in this area for the next merge window.
- Misc janitorial fixes"
* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: Add Spreadtrum PMIC EIC driver support
gpio: Add Spreadtrum EIC driver support
dt-bindings: gpio: Add Spreadtrum EIC controller documentation
gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
pinctrl: qcom: Don't allow protected pins to be requested
gpiolib: Support 'gpio-reserved-ranges' property
gpiolib: Change bitmap allocation to kmalloc_array
gpiolib: Extract mask allocation into subroutine
dt-bindings: gpio: Add a gpio-reserved-ranges property
gpio: mockup: fix a potential crash when creating debugfs entries
gpio: pca953x: add compatibility for pcal6524 and pcal9555a
gpio: dwapb: Add support for a bus clock
gpio: Remove VLA from xra1403 driver
gpio: Remove VLA from MAX3191X driver
gpio: ws16c48: Implement get_multiple callback
gpio: gpio-mm: Implement get_multiple callback
gpio: 104-idi-48: Implement get_multiple callback
gpio: 104-dio-48e: Implement get_multiple callback
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
gpio: pci-idio-16: Implement get_multiple callback
...
|
|
Pull support for 3rd generation Intuos BT device
|
|
Pull a few small generic code cleanups.
|
|
Pull support for NSG-MR5U and NSG-MR7U devices.
|
|
Pull Razer Blade Stealth support improvement and a few generic cleanups
|
|
Small hid-i2c acpi cleanup.
|
|
Pull new hid-elan driver, currently providing support for touchpad
found in certain HP Pavilion x2 laptops.
|
|
Support for Google Hammer device.
|
|
Support for new elecom device.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- ... and a handful of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits)
hwtracing: Add HW tracing support menu
intel_th: Add ACPI glue layer
intel_th: Allow forcing host mode through drvdata
intel_th: Pick up irq number from resources
intel_th: Don't touch switch routing in host mode
intel_th: Use correct method of finding hub
intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
stm class: Make dummy's master/channel ranges configurable
stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
MAINTAINERS: Bestow upon myself the care for drivers/hwtracing
hv: add SPDX license id to Kconfig
hv: add SPDX license to trace
Drivers: hv: vmbus: do not mark HV_PCIE as perf_device
Drivers: hv: vmbus: respect what we get from hv_get_synint_state()
/dev/mem: Avoid overwriting "err" in read_mem()
eeprom: at24: use SPDX identifier instead of GPL boiler-plate
eeprom: at24: simplify the i2c functionality checking
eeprom: at24: fix a line break
eeprom: at24: tweak newlines
eeprom: at24: refactor at24_probe()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 4.17-rc1.
There's really not much here, just a bunch of firmware code
refactoring from Luis as he attempts to wrangle that codebase into
something that is managable, along with a bunch of userspace tests for
it. Other than that, a handful of small bugfixes and reverts of things
that didn't work out.
Full details are in the shortlog, it's not all that much.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (30 commits)
drivers: base: remove check for callback in coredump_store()
mt7601u: use firmware_request_cache() to address cache on reboot
firmware: add firmware_request_cache() to help with cache on reboot
firmware: fix typo on pr_info_once() when ignore_sysfs_fallback is used
firmware: explicitly include vmalloc.h
firmware: ensure the firmware cache is not used on incompatible calls
test_firmware: modify custom fallback tests to use unique files
firmware: add helper to check to see if fw cache is setup
firmware: fix checking for return values for fw_add_devm_name()
rename: _request_firmware_load() fw_load_sysfs_fallback()
test_firmware: test three firmware kernel configs using a proc knob
test_firmware: expand on library with shared helpers
firmware: enable to force disable the fallback mechanism at run time
firmware: enable run time change of forcing fallback loader
firmware: move firmware loader into its own directory
firmware: split firmware fallback functionality into its own file
firmware: move loading timeout under struct firmware_fallback_config
firmware: use helpers for setting up a temporary cache timeout
firmware: simplify CONFIG_FW_LOADER_USER_HELPER_FALLBACK further
drivers: base: add description for .coredump() callback
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big set of Staging/IIO driver patches for 4.17-rc1.
It is a lot, over 500 changes, but not huge by previous kernel release
standards. We deleted more lines than we added again (27k added vs.
91k remvoed), thanks to finally being able to delete the IRDA drivers
and networking code.
We also deleted the ccree crypto driver, but that's coming back in
through the crypto tree to you, in a much cleaned-up form.
Added this round is at lot of "mt7621" device support, which is for an
embedded device that Neil Brown cares about, and of course a handful
of new IIO drivers as well.
And finally, the fsl-mc core code moved out of the staging tree to the
"real" part of the kernel, which is nice to see happen as well.
Full details are in the shortlog, which has all of the tiny cleanup
patches described.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (579 commits)
staging: rtl8723bs: Remove yield call, replace with cond_resched()
staging: rtl8723bs: Replace yield() call with cond_resched()
staging: rtl8723bs: Remove unecessary newlines from 'odm.h'.
staging: rtl8723bs: Rework 'struct _ODM_Phy_Status_Info_' coding style.
staging: rtl8723bs: Rework 'struct _ODM_Per_Pkt_Info_' coding style.
staging: rtl8723bs: Replace NULL pointer comparison with '!'.
staging: rtl8723bs: Factor out rtl8723bs_recv_tasklet() sections.
staging: rtl8723bs: Fix function signature that goes over 80 characters.
staging: rtl8723bs: Fix lines too long in update_recvframe_attrib().
staging: rtl8723bs: Remove unnecessary blank lines in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Change camel case to snake case in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Add missing braces in else statement.
staging: rtl8723bs: Add spaces around ternary operators.
staging: rtl8723bs: Fix lines with trailing open parentheses.
staging: rtl8723bs: Remove unnecessary length #define's.
staging: rtl8723bs: Fix IEEE80211 authentication algorithm constants.
staging: rtl8723bs: Fix alignment in rtw_wx_set_auth().
staging: rtl8723bs: Remove braces from single statement conditionals.
staging: rtl8723bs: Remove unecessary braces from switch statement.
staging: rtl8723bs: Fix newlines in rtw_wx_set_auth().
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver patches for 4.17-rc1
Not all that big really, most are just small fixes and additions to
existing drivers. There's a bunch of work on the imx serial driver
recently for some reason, and a new embedded serial driver added as
well.
Full details are in the shortlog.
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'tty-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (66 commits)
serial: expose buf_overrun count through proc interface
serial: mvebu-uart: fix tx lost characters
tty: serial: msm_geni_serial: Fix return value check in qcom_geni_serial_probe()
tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP
8250-men-mcb: add support for 16z025 and 16z057
powerpc: Mark the variable earlycon_acpi_spcr_enable maybe_unused
serial: stm32: fix initialization of RS485 mode
ARM: dts: STi: Remove "console=ttyASN" from bootargs for STi boards
vt: change SGR 21 to follow the standards
serdev: Fix typo in serdev_device_alloc
ARM: dts: STi: Fix aliases property name for STi boards
tty: st-asc: Update tty alias
serial: stm32: add support for RS485 hardware control mode
dt-bindings: serial: stm32: add RS485 optional properties
selftests: add devpts selftests
devpts: comment devpts_mntget()
devpts: resolve devpts bind-mounts
devpts: hoist out check for DEVPTS_SUPER_MAGIC
serial: 8250: Add Nuvoton NPCM UART
serial: mxs-auart: disable clks of Alphascale ASM9260
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 4.17-rc1.
Lots of USB typeC work happened this round, with code moving from the
staging directory into the "real" part of the kernel, as well as new
infrastructure being added to be able to handle the different types of
"roles" that typeC requires.
There is also the normal huge set of USB gadget controller and driver
updates, along with XHCI changes, and a raft of other tiny fixes all
over the USB tree. And the PHY driver updates are merged in here as
well as they interacted with the USB drivers in some places.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (250 commits)
Revert "USB: serial: ftdi_sio: add Id for Physik Instrumente E-870"
usb: musb: gadget: misplaced out of bounds check
usb: chipidea: imx: Fix ULPI on imx53
usb: chipidea: imx: Cleanup ci_hdrc_imx_platform_flag
usb: chipidea: usbmisc: small clean up
usb: chipidea: usbmisc: evdo can be set e/o reset
usb: chipidea: usbmisc: evdo is only specific to OTG port
USB: serial: ftdi_sio: add Id for Physik Instrumente E-870
usb: dwc3: gadget: never call ->complete() from ->ep_queue()
usb: gadget: udc: core: update usb_ep_queue() documentation
usb: host: Remove the deprecated ATH79 USB host config options
usb: roles: Fix return value check in intel_xhci_usb_probe()
USB: gadget: f_midi: fixing a possible double-free in f_midi
usb: core: Add USB_QUIRK_DELAY_CTRL_MSG to usbcore quirks
usb: core: Copy parameter string correctly and remove superfluous null check
USB: announce bcdDevice as well as idVendor, idProduct.
USB:fix USB3 devices behind USB3 hubs not resuming at hibernate thaw
usb: hub: Reduce warning to notice on power loss
USB: serial: ftdi_sio: add support for Harman FirmwareHubEmulator
USB: serial: cp210x: add ELDAT Easywave RX09 id
...
|
|
Pull networking fixes from David Miller:
"This fixes some fallout from the net-next merge the other day, plus
some non-merge-window-related bug fixes:
1) Fix sparse warnings in bcmgenet, systemport, b53, and mt7530
(Florian Fainelli)
2) pptp does a bogus dst_release() on a route we have a single
refcount on, and attached to a socket, which needs that refcount
(Eric Dumazet)
3) UDP connected sockets on ipv6 can race with route update handling,
resulting in a pre-PMTU update route still stuck on the socket and
thus continuing to get ICMPV6_PKT_TOOBIG errors. We end up never
seeing the updated route. (Alexey Kodanev)
4) Missing list initializer(s) in TIPC (Jon Maloy)
5) Connect phy early to prevent crashes in lan78xx driver (Alexander
Graf)
6) Fix build with modular NVMEM (Arnd Bergmann)
7) netdevsim canot mark nsim_devlink_net_ops and nsim_fib_net_ops as
__net_initdata, as these are references from module unload
unconditionally (Arnd Bergmann)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits)
netdevsim: remove incorrect __net_initdata annotations
sfc: remove ctpio_dmabuf_start from stats
inet: frags: fix ip6frag_low_thresh boundary
tipc: Fix namespace violation in tipc_sk_fill_sock_diag
net: avoid unneeded atomic operation in ip*_append_data()
nvmem: disallow modular CONFIG_NVMEM
net: hns3: fix length overflow when CONFIG_ARM64_64K_PAGES
nfp: use full 40 bits of the NSP buffer address
lan78xx: Connect phy early
nfp: add a separate counter for packets with CHECKSUM_COMPLETE
tipc: Fix missing list initializations in struct tipc_subscription
ipv6: udp: set dst cache for a connected sk if current not valid
ipv6: udp: convert 'connected' to bool type in udpv6_sendmsg()
ipv6: allow to cache dst for a connected sk in ip6_sk_dst_lookup_flow()
ipv6: add a wrapper for ip6_dst_store() with flowi6 checks
net: phy: marvell10g: add thermal hwmon device
pptp: remove a buggy dst release in pptp_connect()
net: dsa: mt7530: Use NULL instead of plain integer
net: dsa: b53: Fix sparse warnings in b53_mmap.c
af_unix: remove redundant lockdep class
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- add AEAD support to crypto engine
- allow batch registration in simd
Algorithms:
- add CFB mode
- add speck block cipher
- add sm4 block cipher
- new test case for crct10dif
- improve scheduling latency on ARM
- scatter/gather support to gcm in aesni
- convert x86 crypto algorithms to skcihper
Drivers:
- hmac(sha224/sha256) support in inside-secure
- aes gcm/ccm support in stm32
- stm32mp1 support in stm32
- ccree driver from staging tree
- gcm support over QI in caam
- add ks-sa hwrng driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (212 commits)
crypto: ccree - remove unused enums
crypto: ahash - Fix early termination in hash walk
crypto: brcm - explicitly cast cipher to hash type
crypto: talitos - don't leak pointers to authenc keys
crypto: qat - don't leak pointers to authenc keys
crypto: picoxcell - don't leak pointers to authenc keys
crypto: ixp4xx - don't leak pointers to authenc keys
crypto: chelsio - don't leak pointers to authenc keys
crypto: caam/qi - don't leak pointers to authenc keys
crypto: caam - don't leak pointers to authenc keys
crypto: lrw - Free rctx->ext with kzfree
crypto: talitos - fix IPsec cipher in length
crypto: Deduplicate le32_to_cpu_array() and cpu_to_le32_array()
crypto: doc - clarify hash callbacks state machine
crypto: api - Keep failed instances alive
crypto: api - Make crypto_alg_lookup static
crypto: api - Remove unused crypto_type lookup function
crypto: chelsio - Remove declaration of static function from header
crypto: inside-secure - hmac(sha224) support
crypto: inside-secure - hmac(sha256) support
..
|
|
Prepare input updates for 4.17 merge window.
|
|
The touch sensor buttons on Sony VAIO VGN-CS series laptops (e.g.
VGN-CS31S) are a separate PS/2 device. As the MUX is disabled for all
VAIO machines by the nomux blacklist, the data from touch sensor
buttons and touchpad are combined. The protocol used by the buttons is
probably similar to the touchpad protocol (both are Synaptics) so both
devices get enabled. The controller combines the data, creating a mess
which results in random button clicks, touchpad stopping working and
lost sync error messages:
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 4
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: issuing reconnect request
Add a new i8042_dmi_forcemux_table whitelist with VGN-CS.
With MUX enabled, touch sensor buttons are detected as separate device
(and left disabled as there's currently no driver), fixing all touchpad
problems.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Nothing particularly stands out here, probably because people were
tied up with spectre/meltdown stuff last time around. Still, the main
pieces are:
- Rework of our CPU features framework so that we can whitelist CPUs
that don't require kpti even in a heterogeneous system
- Support for the IDC/DIC architecture extensions, which allow us to
elide instruction and data cache maintenance when writing out
instructions
- Removal of the large memory model which resulted in suboptimal
codegen by the compiler and increased the use of literal pools,
which could potentially be used as ROP gadgets since they are
mapped as executable
- Rework of forced signal delivery so that the siginfo_t is
well-formed and handling of show_unhandled_signals is consolidated
and made consistent between different fault types
- More siginfo cleanup based on the initial patches from Eric
Biederman
- Workaround for Cortex-A55 erratum #1024718
- Some small ACPI IORT updates and cleanups from Lorenzo Pieralisi
- Misc cleanups and non-critical fixes"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (70 commits)
arm64: uaccess: Fix omissions from usercopy whitelist
arm64: fpsimd: Split cpu field out from struct fpsimd_state
arm64: tlbflush: avoid writing RES0 bits
arm64: cmpxchg: Include linux/compiler.h in asm/cmpxchg.h
arm64: move percpu cmpxchg implementation from cmpxchg.h to percpu.h
arm64: cmpxchg: Include build_bug.h instead of bug.h for BUILD_BUG
arm64: lse: Include compiler_types.h and export.h for out-of-line LL/SC
arm64: fpsimd: include <linux/init.h> in fpsimd.h
drivers/perf: arm_pmu_platform: do not warn about affinity on uniprocessor
perf: arm_spe: include linux/vmalloc.h for vmap()
Revert "arm64: Revert L1_CACHE_SHIFT back to 6 (64-byte cache line size)"
arm64: cpufeature: Avoid warnings due to unused symbols
arm64: Add work around for Arm Cortex-A55 Erratum 1024718
arm64: Delay enabling hardware DBM feature
arm64: Add MIDR encoding for Arm Cortex-A55 and Cortex-A35
arm64: capabilities: Handle shared entries
arm64: capabilities: Add support for checks based on a list of MIDRs
arm64: Add helpers for checking CPU MIDR against a range
arm64: capabilities: Clean up midr range helpers
arm64: capabilities: Change scope of VHE to Boot CPU feature
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The usual pile of boring changes:
- Consolidate tasklet functions to share code instead of duplicating
it
- The first step for making the low level entry handler management on
multi-platform kernels generic
- A new sysfs file which allows to retrieve the wakeup state of
interrupts.
- Ensure that the interrupt thread follows the effective affinity and
not the programmed affinity to avoid cross core wakeups.
- Two new interrupt controller drivers (Microsemi Ocelot and Qualcomm
PDC)
- Fix the wakeup path clock handling for Reneasas interrupt chips.
- Rework the boot time register reset for ARM GIC-V2/3
- Better suspend/resume support for ARM GIV-V3/ITS
- Add missing locking to the ARM GIC set_type() callback
- Small fixes for the irq simulator code
- SPDX identifiers for the irq core code and removal of boiler plate
- Small cleanups all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
openrisc: Set CONFIG_MULTI_IRQ_HANDLER
arm64: Set CONFIG_MULTI_IRQ_HANDLER
genirq: Make GENERIC_IRQ_MULTI_HANDLER depend on !MULTI_IRQ_HANDLER
irqchip/gic: Take lock when updating irq type
irqchip/gic: Update supports_deactivate static key to modern api
irqchip/gic-v3: Ensure GICR_CTLR.EnableLPI=0 is observed before enabling
irqchip: Add a driver for the Microsemi Ocelot controller
dt-bindings: interrupt-controller: Add binding for the Microsemi Ocelot interrupt controller
irqchip/gic-v3: Probe for SCR_EL3 being clear before resetting AP0Rn
irqchip/gic-v3: Don't try to reset AP0Rn
irqchip/gic-v3: Do not check trigger configuration of partitionned LPIs
genirq: Remove license boilerplate/references
genirq: Add missing SPDX identifiers
genirq/matrix: Cleanup SPDX identifier
genirq: Cleanup top of file comments
genirq: Pass desc to __irq_free instead of irq number
irqchip/gic-v3: Loudly complain about the use of IRQ_TYPE_NONE
irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE
RISC-V: Move to the new GENERIC_IRQ_MULTI_HANDLER handler
genirq: Add CONFIG_GENERIC_IRQ_MULTI_HANDLER
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull time(r) updates from Thomas Gleixner:
"A small set of updates for timers and timekeeping:
- The most interesting change is the consolidation of clock MONOTONIC
and clock BOOTTIME.
Clock MONOTONIC behaves now exactly like clock BOOTTIME and does
not longer ignore the time spent in suspend. A new clock
MONOTONIC_ACTIVE is provived which behaves like clock MONOTONIC in
kernels before this change. This allows applications to
programmatically check for the clock MONOTONIC behaviour.
As discussed in the review thread, this has the potential of
breaking user space and we might have to revert this. Knock on wood
that we can avoid that exercise.
- Updates to the NTP mechanism to improve accuracy
- A new kernel internal data structure to aid the ongoing Y2038 work.
- Cleanups and simplifications of the clocksource code.
- Make the alarmtimer code play nicely with debugobjects"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
alarmtimer: Init nanosleep alarm timer on stack
y2038: Introduce struct __kernel_old_timeval
tracing: Unify the "boot" and "mono" tracing clocks
hrtimer: Unify MONOTONIC and BOOTTIME clock behavior
posix-timers: Unify MONOTONIC and BOOTTIME clock behavior
timekeeping: Remove boot time specific code
Input: Evdev - unify MONOTONIC and BOOTTIME clock behavior
timekeeping: Make the MONOTONIC clock behave like the BOOTTIME clock
timekeeping: Add the new CLOCK_MONOTONIC_ACTIVE clock
timekeeping/ntp: Determine the multiplier directly from NTP tick length
timekeeping/ntp: Don't align NTP frequency adjustments to ticks
clocksource: Use ATTRIBUTE_GROUPS
clocksource: Use DEVICE_ATTR_RW/RO/WO to define device attributes
clocksource: Don't walk the clocksource list for empty override
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random updates from Ted Ts'o:
"A few random (cough, cough) cleanups for the /dev/random driver"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
drivers/char/random.c: remove unused dont_count_entropy
random: optimize add_interrupt_randomness
random: always fill buffer in get_random_bytes_wait
random: use a tighter cap in credit_entropy_bits_safe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs dcache updates from Al Viro:
"Part of this is what the trylock loop elimination series has turned
into, part making d_move() preserve the parent (and thus the path) of
victim, plus some general cleanups"
* 'work.dcache' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (22 commits)
d_genocide: move export to definition
fold dentry_lock_for_move() into its sole caller and clean it up
make non-exchanging __d_move() copy ->d_parent rather than swap them
oprofilefs: don't oops on allocation failure
lustre: get rid of pointless casts to struct dentry *
debugfs_lookup(): switch to lookup_one_len_unlocked()
fold lookup_real() into __lookup_hash()
take out orphan externs (empty_string/slash_string)
split d_path() and friends into a separate file
dcache.c: trim includes
fs/dcache: Avoid a try_lock loop in shrink_dentry_list()
get rid of trylock loop around dentry_kill()
handle move to LRU in retain_dentry()
dput(): consolidate the "do we need to retain it?" into an inlined helper
split the slow part of lock_parent() off
now lock_parent() can't run into killed dentry
get rid of trylock loop in locking dentries on shrink list
d_delete(): get rid of trylock loop
fs/dcache: Move dentry_kill() below lock_parent()
fs/dcache: Remove stale comment from dentry_kill()
...
|
|
The __net_initdata section cannot currently be used for structures that
get cleaned up in an exitcall using unregister_pernet_operations:
WARNING: vmlinux.o(.text+0x868c34): Section mismatch in reference from the function nsim_devlink_exit() to the (unknown reference) .init.data:(unknown)
The function nsim_devlink_exit() references
the (unknown reference) __initdata (unknown).
This is often because nsim_devlink_exit lacks a __initdata
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.text+0x868c64): Section mismatch in reference from the function nsim_devlink_init() to the (unknown reference) .init.data:(unknown)
WARNING: vmlinux.o(.text+0x8692bc): Section mismatch in reference from the function nsim_fib_exit() to the (unknown reference) .init.data:(unknown)
WARNING: vmlinux.o(.text+0x869300): Section mismatch in reference from the function nsim_fib_init() to the (unknown reference) .init.data:(unknown)
As that warning tells us, discarding the structure after a module is
loaded would lead to a undefined behavior when that module is removed.
It might be possible to change that annotation so it has no effect for
loadable modules, but I have not figured out exactly how to do that, and
we want this to be fixed in -rc1.
This just removes the annotations, just like we do for all other such
modules.
Fixes: 37923ed6b8ce ("netdevsim: Add simple FIB resource controller via devlink")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ctpio_dmabuf_start entry is not actually a stat and shouldn't
be exposed to ethtool.
Fixes: 2c0b6ee837db ("sfc: expose CTPIO stats on NICs that support them")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new of_get_nvmem_mac_address() helper function causes a link error
with CONFIG_NVMEM=m:
drivers/of/of_net.o: In function `of_get_nvmem_mac_address':
of_net.c:(.text+0x168): undefined reference to `of_nvmem_cell_get'
of_net.c:(.text+0x19c): undefined reference to `nvmem_cell_read'
of_net.c:(.text+0x1a8): undefined reference to `nvmem_cell_put'
I could not come up with a good solution for this, as the code is always
built-in. Using an #if IS_REACHABLE() check around it would solve the
link time issue but then stop it from working in that configuration.
Making of_nvmem_cell_get() an inline function could also solve that, but
seems a bit ugly since it's somewhat larger than most inline functions,
and it would just bring that problem into the callers. Splitting the
function into a separate file might be an alternative.
This uses the big hammer by making CONFIG_NVMEM itself a 'bool' symbol,
which avoids the problem entirely but makes the vmlinux larger for anyone
that might use NVMEM support but doesn't need it built-in otherwise.
Fixes: 9217e566bdee ("of_net: Implement of_get_nvmem_mac_address helper")
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mike Looijmans
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enable the config item "CONFIG_ARM64_64K_PAGES", the size of PAGE_SIZE
is 65536(64K). But the type of length is u16, it will overflow. So change it
to u32.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NSP default buffer is a piece of NFP memory where additional
command data can be placed. Its format has been copied from
host buffer, but the PCIe selection bits do not make sense in
this case. If those get masked out from a NFP address - writes
to random place in the chip memory may be issued and crash the
device.
Even in the general NSP buffer case, it doesn't make sense to have the
PCIe selection bits there anymore. These are unused at the moment, and
when it becomes necessary, the PCIe selection bits should rather be
moved to another register to utilise more bits for the buffer address.
This has never been an issue because the buffer used to be
allocated in memory with less-than-38-bit-long address but that
is about to change.
Fixes: 1a64821c6af7 ("nfp: add support for service processor access")
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using wicked with a lan78xx device attached to the system, we
end up with ethtool commands issued on the device before an ifup
got issued. That lead to the following crash:
Unable to handle kernel NULL pointer dereference at virtual address 0000039c
pgd = ffff800035b30000
[0000039c] *pgd=0000000000000000
Internal error: Oops: 96000004 [#1] SMP
Modules linked in: [...]
Supported: Yes
CPU: 3 PID: 638 Comm: wickedd Tainted: G E 4.12.14-0-default #1
Hardware name: raspberrypi rpi/rpi, BIOS 2018.03-rc2 02/21/2018
task: ffff800035e74180 task.stack: ffff800036718000
PC is at phy_ethtool_ksettings_get+0x20/0x98
LR is at lan78xx_get_link_ksettings+0x44/0x60 [lan78xx]
pc : [<ffff0000086f7f30>] lr : [<ffff000000dcca84>] pstate: 20000005
sp : ffff80003671bb20
x29: ffff80003671bb20 x28: ffff800035e74180
x27: ffff000008912000 x26: 000000000000001d
x25: 0000000000000124 x24: ffff000008f74d00
x23: 0000004000114809 x22: 0000000000000000
x21: ffff80003671bbd0 x20: 0000000000000000
x19: ffff80003671bbd0 x18: 000000000000040d
x17: 0000000000000001 x16: 0000000000000000
x15: 0000000000000000 x14: ffffffffffffffff
x13: 0000000000000000 x12: 0000000000000020
x11: 0101010101010101 x10: fefefefefefefeff
x9 : 7f7f7f7f7f7f7f7f x8 : fefefeff31677364
x7 : 0000000080808080 x6 : ffff80003671bc9c
x5 : ffff80003671b9f8 x4 : ffff80002c296190
x3 : 0000000000000000 x2 : 0000000000000000
x1 : ffff80003671bbd0 x0 : ffff80003671bc00
Process wickedd (pid: 638, stack limit = 0xffff800036718000)
Call trace:
Exception stack(0xffff80003671b9e0 to 0xffff80003671bb20)
b9e0: ffff80003671bc00 ffff80003671bbd0 0000000000000000 0000000000000000
ba00: ffff80002c296190 ffff80003671b9f8 ffff80003671bc9c 0000000080808080
ba20: fefefeff31677364 7f7f7f7f7f7f7f7f fefefefefefefeff 0101010101010101
ba40: 0000000000000020 0000000000000000 ffffffffffffffff 0000000000000000
ba60: 0000000000000000 0000000000000001 000000000000040d ffff80003671bbd0
ba80: 0000000000000000 ffff80003671bbd0 0000000000000000 0000004000114809
baa0: ffff000008f74d00 0000000000000124 000000000000001d ffff000008912000
bac0: ffff800035e74180 ffff80003671bb20 ffff000000dcca84 ffff80003671bb20
bae0: ffff0000086f7f30 0000000020000005 ffff80002c296000 ffff800035223900
bb00: 0000ffffffffffff 0000000000000000 ffff80003671bb20 ffff0000086f7f30
[<ffff0000086f7f30>] phy_ethtool_ksettings_get+0x20/0x98
[<ffff000000dcca84>] lan78xx_get_link_ksettings+0x44/0x60 [lan78xx]
[<ffff0000087cbc40>] ethtool_get_settings+0x68/0x210
[<ffff0000087cc0d4>] dev_ethtool+0x214/0x2180
[<ffff0000087e5008>] dev_ioctl+0x400/0x630
[<ffff00000879dd00>] sock_do_ioctl+0x70/0x88
[<ffff00000879f5f8>] sock_ioctl+0x208/0x368
[<ffff0000082cde10>] do_vfs_ioctl+0xb0/0x848
[<ffff0000082ce634>] SyS_ioctl+0x8c/0xa8
Exception stack(0xffff80003671bec0 to 0xffff80003671c000)
bec0: 0000000000000009 0000000000008946 0000fffff4e841d0 0000aa0032687465
bee0: 0000aaaafa2319d4 0000fffff4e841d4 0000000032687465 0000000032687465
bf00: 000000000000001d 7f7fff7f7f7f7f7f 72606b622e71ff4c 7f7f7f7f7f7f7f7f
bf20: 0101010101010101 0000000000000020 ffffffffffffffff 0000ffff7f510c68
bf40: 0000ffff7f6a9d18 0000ffff7f44ce30 000000000000040d 0000ffff7f6f98f0
bf60: 0000fffff4e842c0 0000000000000001 0000aaaafa2c2e00 0000ffff7f6ab000
bf80: 0000fffff4e842c0 0000ffff7f62a000 0000aaaafa2b9f20 0000aaaafa2c2e00
bfa0: 0000fffff4e84818 0000fffff4e841a0 0000ffff7f5ad0cc 0000fffff4e841a0
bfc0: 0000ffff7f44ce3c 0000000080000000 0000000000000009 000000000000001d
bfe0: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
The culprit is quite simple: The driver tries to access the phy left and right,
but only actually has a working reference to it when the device is up.
The fix thus is quite simple too: Get a reference to the phy on probe already
and keep it even when the device is going down.
With this patch applied, I can successfully run wicked on my system and bring
the interface up and down as many times as I want, without getting NULL pointer
dereferences in between.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently counting packets with CHECKSUM_COMPLETE as
"hw_rx_csum_ok". This is confusing. Add a new counter.
To make sure it fits in the same cacheline move the less used
error counter to a different location.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a thermal monitoring device for the Marvell 88x3310, which updates
once a second. We also need to hook into the suspend/resume mechanism
to ensure that the thermal monitoring is reconfigured when we resume.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once dst has been cached in socket via sk_setup_caps(),
it is illegal to call ip_rt_put() (or dst_release()),
since sk_setup_caps() did not change dst refcount.
We can still dereference it since we hold socket lock.
Caugth by syzbot :
BUG: KASAN: use-after-free in atomic_dec_return include/asm-generic/atomic-instrumented.h:198 [inline]
BUG: KASAN: use-after-free in dst_release+0x27/0xa0 net/core/dst.c:185
Write of size 4 at addr ffff8801c54dc040 by task syz-executor4/20088
CPU: 1 PID: 20088 Comm: syz-executor4 Not tainted 4.16.0+ #376
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x1a7/0x27d lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report+0x23c/0x360 mm/kasan/report.c:412
check_memory_region_inline mm/kasan/kasan.c:260 [inline]
check_memory_region+0x137/0x190 mm/kasan/kasan.c:267
kasan_check_write+0x14/0x20 mm/kasan/kasan.c:278
atomic_dec_return include/asm-generic/atomic-instrumented.h:198 [inline]
dst_release+0x27/0xa0 net/core/dst.c:185
sk_dst_set include/net/sock.h:1812 [inline]
sk_dst_reset include/net/sock.h:1824 [inline]
sock_setbindtodevice net/core/sock.c:610 [inline]
sock_setsockopt+0x431/0x1b20 net/core/sock.c:707
SYSC_setsockopt net/socket.c:1845 [inline]
SyS_setsockopt+0x2ff/0x360 net/socket.c:1828
do_syscall_64+0x281/0x940 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
RIP: 0033:0x4552d9
RSP: 002b:00007f4878126c68 EFLAGS: 00000246 ORIG_RAX: 0000000000000036
RAX: ffffffffffffffda RBX: 00007f48781276d4 RCX: 00000000004552d9
RDX: 0000000000000019 RSI: 0000000000000001 RDI: 0000000000000013
RBP: 000000000072bea0 R08: 0000000000000010 R09: 0000000000000000
R10: 00000000200010c0 R11: 0000000000000246 R12: 00000000ffffffff
R13: 0000000000000526 R14: 00000000006fac30 R15: 0000000000000000
Allocated by task 20088:
save_stack+0x43/0xd0 mm/kasan/kasan.c:447
set_track mm/kasan/kasan.c:459 [inline]
kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:552
kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:489
kmem_cache_alloc+0x12e/0x760 mm/slab.c:3542
dst_alloc+0x11f/0x1a0 net/core/dst.c:104
rt_dst_alloc+0xe9/0x540 net/ipv4/route.c:1520
__mkroute_output net/ipv4/route.c:2265 [inline]
ip_route_output_key_hash_rcu+0xa49/0x2c60 net/ipv4/route.c:2493
ip_route_output_key_hash+0x20b/0x370 net/ipv4/route.c:2322
__ip_route_output_key include/net/route.h:126 [inline]
ip_route_output_flow+0x26/0xa0 net/ipv4/route.c:2577
ip_route_output_ports include/net/route.h:163 [inline]
pptp_connect+0xa84/0x1170 drivers/net/ppp/pptp.c:453
SYSC_connect+0x213/0x4a0 net/socket.c:1639
SyS_connect+0x24/0x30 net/socket.c:1620
do_syscall_64+0x281/0x940 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
Freed by task 20082:
save_stack+0x43/0xd0 mm/kasan/kasan.c:447
set_track mm/kasan/kasan.c:459 [inline]
__kasan_slab_free+0x11a/0x170 mm/kasan/kasan.c:520
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:527
__cache_free mm/slab.c:3486 [inline]
kmem_cache_free+0x83/0x2a0 mm/slab.c:3744
dst_destroy+0x266/0x380 net/core/dst.c:140
dst_destroy_rcu+0x16/0x20 net/core/dst.c:153
__rcu_reclaim kernel/rcu/rcu.h:178 [inline]
rcu_do_batch kernel/rcu/tree.c:2675 [inline]
invoke_rcu_callbacks kernel/rcu/tree.c:2930 [inline]
__rcu_process_callbacks kernel/rcu/tree.c:2897 [inline]
rcu_process_callbacks+0xd6c/0x17b0 kernel/rcu/tree.c:2914
__do_softirq+0x2d7/0xb85 kernel/softirq.c:285
The buggy address belongs to the object at ffff8801c54dc000
which belongs to the cache ip_dst_cache of size 168
The buggy address is located 64 bytes inside of
168-byte region [ffff8801c54dc000, ffff8801c54dc0a8)
The buggy address belongs to the page:
page:ffffea0007153700 count:1 mapcount:0 mapping:ffff8801c54dc000 index:0x0
flags: 0x2fffc0000000100(slab)
raw: 02fffc0000000100 ffff8801c54dc000 0000000000000000 0000000100000010
raw: ffffea0006b34b20 ffffea0006b6c1e0 ffff8801d674a1c0 0000000000000000
page dumped because: kasan: bad access detected
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We would be passing 0 instead of NULL as the rsp argument to
mt7530_fdb_cmd(), fix that.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sparse complains about the following warnings:
drivers/net/dsa/b53/b53_mmap.c:33:31: warning: incorrect type in
initializer (different address spaces)
drivers/net/dsa/b53/b53_mmap.c:33:31: expected unsigned char
[noderef] [usertype] <asn:2>*regs
drivers/net/dsa/b53/b53_mmap.c:33:31: got void *priv
and indeed, while what we are doing is functional, we are dereferencing
a void * pointer into a void __iomem * which is not great. Just use the
defined b53_mmap_priv structure which holds our register base and use
that.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb->protocol is a __be16 which we would be calling htons() against,
while this is not wrong per-se as it correctly results in swapping the
value on LE hosts, this still upsets sparse. Adopt a similar pattern to
what other drivers do and just assign ip_ver to skb->protocol, and then
use htons() against the different constants such that the compiler can
resolve the values at build time.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb->protocol is a __be16 which we would be calling htons() against,
while this is not wrong per-se as it correctly results in swapping the
value on LE hosts, this still upsets sparse. Adopt a similar pattern to
what other drivers do and just assign ip_ver to skb->protocol, and then
use htons() against the different constants such that the compiler can
resolve the values at build time.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
"Nothing too interesting.
The biggest change is refcnting fix for ata_host - the bug is recent
and can only be triggered on controller hotplug, so very few are
hitting it.
There also are a number of trivial license / error message changes and
some hardware specific changes"
* 'for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (23 commits)
ahci: imx: add the imx8qm ahci sata support
libata: ensure host is free'd on error exit paths
ata: ahci-platform: add reset control support
ahci: imx: fix the build warning
ata: add Amiga Gayle PATA controller driver
ahci: imx: add the imx6qp ahci sata support
ata: change Tegra124 to Tegra
ata: ahci_tegra: Add AHCI support for Tegra210
ata: ahci_tegra: disable DIPM
ata: ahci_tegra: disable devslp for Tegra124
ata: ahci_tegra: initialize regulators from soc struct
ata: ahci_tegra: Update initialization sequence
dt-bindings: Tegra210: add binding documentation
libata: add refcounting to ata_host
pata_bk3710: clarify license version and use SPDX header
pata_falcon: clarify license version and use SPDX header
pata_it821x: Delete an error message for a failed memory allocation in it821x_firmware_command()
pata_macio: Delete an error message for a failed memory allocation in two functions
pata_mpc52xx: Delete an error message for a failed memory allocation in mpc52xx_ata_probe()
sata_dwc_460ex: Delete an error message for a failed memory allocation in sata_dwc_port_start()
...
|
|
Somewhat nasty merge due to conflicts between "33b28357dd00 scsi:
qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan" and "2b5b96473efc
scsi: qla2xxx: Fix FC-NVMe LUN discovery"
Merge is non-trivial and has been verified by Qlogic (Cavium)
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new CEC pin injection code for testing purposes
- DVB frontend cxd2099 promoted from staging
- new platform driver for Sony cxd2880 DVB devices
- new sensor drivers: mt9t112, ov2685, ov5695, ov772x, tda1997x,
tw9910.c
- removal of unused cx18 and ivtv alsa mixers
- the reneseas-ceu driver doesn't depend on soc_camera anymore and
moved from staging
- removed the mantis_vp3028 driver, unused since 2009
- s5p-mfc: add support for version 10 of the MSP
- added a decoder for imon protocol
- atomisp: lots of cleanups
- imx074 and mt9t031: don't depend on soc_camera anymore, being
promoted from staging
- added helper functions to better support DVB I2C binding
- lots of driver improvements and cleanups
* tag 'media/v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (438 commits)
media: v4l2-ioctl: rename a temp var that stores _IOC_SIZE(cmd)
media: fimc-capture: get rid of two warnings
media: dvb-usb-v2: fix a missing dependency of I2C_MUX
media: uvc: to the right check at uvc_ioctl_enum_framesizes()
media: cec-core: fix a bug at cec_error_inj_write()
media: tda9840: cleanup a warning
media: tm6000: avoid casting just to print pointer address
media: em28xx-input: improve error handling code
media: zr364xx: avoid casting just to print pointer address
media: vivid-radio-rx: add a cast to avoid a warning
media: saa7134-alsa: don't use casts to print a buffer address
media: solo6x10: get rid of an address space warning
media: zoran: don't cast pointers to print them
media: ir-kbd-i2c: change the if logic to avoid a warning
media: ir-kbd-i2c: improve error handling code
media: saa7134-input: improve error handling
media: s2255drv: fix a casting warning
media: ivtvfb: Cleanup some warnings
media: videobuf-dma-sg: Fix a weird cast
soc_camera: fix a weird cast on printk
...
|
