Age | Commit message (Collapse) | Author | Files | Lines |
|
transport device
[ Upstream commit 8725aa4fa7ded30211ebd28bb1c9bae806eb3841 ]
In the event that the RMI device is unreachable, the calls to rmi_set_mode() or
rmi_set_page() will fail before registering the RMI transport device. When the
device is removed, rmi_remove() will call rmi_unregister_transport_device()
which will attempt to access the rmi_dev pointer which was not set.
This patch adds a check of the RMI_STARTED bit before calling
rmi_unregister_transport_device(). The RMI_STARTED bit is only set
after rmi_register_transport_device() completes successfully.
The kernel oops was reported in this message:
https://www.spinics.net/lists/linux-input/msg58433.html
[jkosina@suse.cz: reworded changelog as agreed with Andrew]
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reported-by: Federico Cerutti <federico@ceres-c.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2dbc6f113acd74c66b04bf49fb027efd830b1c5a ]
Per Microsoft spec, usage 0xC5 (page 0xFF) returns a blob containing
data used to verify the touchpad as a Windows Precision Touchpad.
0x85, REPORTID_PTPHQA, // REPORT_ID (PTPHQA)
0x09, 0xC5, // USAGE (Vendor Usage 0xC5)
0x15, 0x00, // LOGICAL_MINIMUM (0)
0x26, 0xff, 0x00, // LOGICAL_MAXIMUM (0xff)
0x75, 0x08, // REPORT_SIZE (8)
0x96, 0x00, 0x01, // REPORT_COUNT (0x100 (256))
0xb1, 0x02, // FEATURE (Data,Var,Abs)
However, some devices, namely Microsoft's Surface line of products
instead implement a "segmented device certification report" (usage 0xC6)
which returns the same report, but in smaller chunks.
0x06, 0x00, 0xff, // USAGE_PAGE (Vendor Defined)
0x85, REPORTID_PTPHQA, // REPORT_ID (PTPHQA)
0x09, 0xC6, // USAGE (Vendor usage for segment #)
0x25, 0x08, // LOGICAL_MAXIMUM (8)
0x75, 0x08, // REPORT_SIZE (8)
0x95, 0x01, // REPORT_COUNT (1)
0xb1, 0x02, // FEATURE (Data,Var,Abs)
0x09, 0xC7, // USAGE (Vendor Usage)
0x26, 0xff, 0x00, // LOGICAL_MAXIMUM (0xff)
0x95, 0x20, // REPORT_COUNT (32)
0xb1, 0x02, // FEATURE (Data,Var,Abs)
By expanding Win8 touchpad detection to also look for the segmented
report, all Surface touchpads are now properly recognized by
hid-multitouch.
Signed-off-by: Blaž Hrastnik <blaz@mxxn.io>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4e24e37d5313edca8b4ab86f240c046c731e28d6 ]
drivers/nvdimm/btt.c: In function 'btt_read_pg':
drivers/nvdimm/btt.c:1264:8: warning: variable 'rc' set but not used
[-Wunused-but-set-variable]
int rc;
^~
Add a ratelimited message in case a storm of errors is encountered.
Fixes: d9b83c756953 ("libnvdimm, btt: rework error clearing")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/1572530719-32161-1-git-send-email-cai@lca.pw
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0c8432236dea20a95f68fa17989ea3f8af0186a5 ]
On some ThinkPad L390 some raydium 3118 touchscreen devices
doesn't response any data after reset, but some does.
Add this ID to no irq quirk,
then don't wait for any response alike on these touchscreens.
All kinds of raydium 3118 devices work fine.
BugLink: https://bugs.launchpad.net/bugs/1849721
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 61005d65b6c7dcf61c19516e6ebe5acc02d2cdda ]
My Logitech M185 (PID:4038) 2.4 GHz wireless HID++ mouse is causing
intermittent errors like these in the log:
[11091.034857] logitech-hidpp-device 0003:046D:4038.0006: hidpp20_batterylevel_get_battery_capacity: received protocol error 0x09
[12388.031260] logitech-hidpp-device 0003:046D:4038.0006: hidpp20_batterylevel_get_battery_capacity: received protocol error 0x09
[16613.718543] logitech-hidpp-device 0003:046D:4038.0006: hidpp20_batterylevel_get_battery_capacity: received protocol error 0x09
[23529.938728] logitech-hidpp-device 0003:046D:4038.0006: hidpp20_batterylevel_get_battery_capacity: received protocol error 0x09
We are already silencing error-code 0x09 (HIDPP_ERROR_RESOURCE_ERROR)
errors in other places, lets do the same in
hidpp20_batterylevel_get_battery_capacity to remove these harmless,
but scary looking errors from the dmesg output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f1a0094cbbe97a5f8aca7bdc64bfe43ac9dc6879 ]
The PixArt OEM mouse disconnets/reconnects every minute on
Linux. All contents of dmesg are repetitive:
[ 1465.810014] usb 1-2.2: USB disconnect, device number 20
[ 1467.431509] usb 1-2.2: new low-speed USB device number 21 using xhci_hcd
[ 1467.654982] usb 1-2.2: New USB device found, idVendor=03f0,idProduct=1f4a, bcdDevice= 1.00
[ 1467.654985] usb 1-2.2: New USB device strings: Mfr=1, Product=2,SerialNumber=0
[ 1467.654987] usb 1-2.2: Product: HP USB Optical Mouse
[ 1467.654988] usb 1-2.2: Manufacturer: PixArt
[ 1467.699722] input: PixArt HP USB Optical Mouse as /devices/pci0000:00/0000:00:07.1/0000:05:00.3/usb1/1-2/1-2.2/1-2.2:1.0/0003:03F0:1F4A.0012/input/input19
[ 1467.700124] hid-generic 0003:03F0:1F4A.0012: input,hidraw0: USB HID v1.11 Mouse [PixArt HP USB Optical Mouse] on usb-0000:05:00.3-2.2/input0
So add HID_QUIRK_ALWAYS_POLL for this one as well.
Test the patch, the mouse is no longer disconnected and there are no
duplicate logs in dmesg.
Reference:
https://github.com/sriemer/fix-linux-mouse
Signed-off-by: Jinke Fan <fanjinke@hygon.cn>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9fcc34b1a6dd4b8e5337e2b6ef45e428897eca6b ]
In bch_mca_scan(), the number of shrinking btree node is calculated
by code like this,
unsigned long nr = sc->nr_to_scan;
nr /= c->btree_pages;
nr = min_t(unsigned long, nr, mca_can_free(c));
variable sc->nr_to_scan is number of objects (here is bcache B+tree
nodes' number) to shrink, and pointer variable sc is sent from memory
management code as parametr of a callback.
If sc->nr_to_scan is smaller than c->btree_pages, after the above
calculation, variable 'nr' will be 0 and nothing will be shrunk. It is
frequeently observed that only 1 or 2 is set to sc->nr_to_scan and make
nr to be zero. Then bch_mca_scan() will do nothing more then acquiring
and releasing mutex c->bucket_lock.
This patch checkes whether nr is 0 after the above calculation, if 0
is the result then set 1 to variable 'n'. Then at least bch_mca_scan()
will try to shrink a single B+tree node.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 46acbcb4849b2ca2e6e975e7c8130c1d61c8fd0c ]
The pxa27x platforms have a single IP with 2 drivers, sa1100-rtc and
rtc-pxa drivers.
A previous patch fixed the sa1100-rtc case, but the pxa-rtc wasn't
fixed. This patch completes the previous one.
Fixes: 8b6d10345e16 ("clk: pxa: add missing pxa27x clocks for Irda and sa1100-rtc")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lkml.kernel.org/r/20191026194420.11918-1-robert.jarzmik@free.fr
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 79172ab20bfd8437b277254028efdb68484e2c21 ]
Since the scsi subsystem adopted the blk-mq API, a host with zero
sg_tablesize crashes with a NULL pointer dereference.
blk_queue_max_segments: set to minimum 1
scsi 0:0:0:0: Direct-Access QEMU QEMU HARDDISK 2.5+ PQ: 0 ANSI: 5
scsi target0:0:0: Beginning Domain Validation
scsi target0:0:0: Domain Validation skipping write tests
scsi target0:0:0: Ending Domain Validation
blk_queue_max_segments: set to minimum 1
scsi 0:0:1:0: Direct-Access QEMU QEMU HARDDISK 2.5+ PQ: 0 ANSI: 5
scsi target0:0:1: Beginning Domain Validation
scsi target0:0:1: Domain Validation skipping write tests
scsi target0:0:1: Ending Domain Validation
blk_queue_max_segments: set to minimum 1
scsi 0:0:2:0: CD-ROM QEMU QEMU CD-ROM 2.5+ PQ: 0 ANSI: 5
scsi target0:0:2: Beginning Domain Validation
scsi target0:0:2: Domain Validation skipping write tests
scsi target0:0:2: Ending Domain Validation
blk_queue_max_segments: set to minimum 1
blk_queue_max_segments: set to minimum 1
blk_queue_max_segments: set to minimum 1
blk_queue_max_segments: set to minimum 1
sr 0:0:2:0: Power-on or device reset occurred
sd 0:0:0:0: Power-on or device reset occurred
sd 0:0:1:0: Power-on or device reset occurred
sd 0:0:0:0: [sda] 10485762 512-byte logical blocks: (5.37 GB/5.00 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Unable to handle kernel NULL pointer dereference at virtual address (ptrval)
Oops: 00000000
Modules linked in:
PC: [<001cd874>] blk_mq_free_request+0x66/0xe2
SR: 2004 SP: (ptrval) a2: 00874520
d0: 00000000 d1: 00000000 d2: 009ba800 d3: 00000000
d4: 00000000 d5: 08000002 a0: 0087be68 a1: 009a81e0
Process kworker/u2:2 (pid: 15, task=(ptrval))
Frame format=7 eff addr=0000007a ssw=0505 faddr=0000007a
wb 1 stat/addr/data: 0000 00000000 00000000
wb 2 stat/addr/data: 0000 00000000 00000000
wb 3 stat/addr/data: 0000 0000007a 00000000
push data: 00000000 00000000 00000000 00000000
Stack from 0087bd98:
00000002 00000000 0087be72 009a7820 0087bdb4 001c4f6c 009a7820 0087bdd4
0024d200 009a7820 0024d0dc 0087be72 009baa00 0087be68 009a5000 0087be7c
00265d10 009a5000 0087be72 00000003 00000000 00000000 00000000 0087be68
00000bb8 00000005 00000000 00000000 00000000 00000000 00265c56 00000000
009ba60c 0036ddf4 00000002 ffffffff 009baa00 009ba600 009a50d6 0087be74
00227ba0 009baa08 00000001 009baa08 009ba60c 0036ddf4 00000000 00000000
Call Trace: [<001c4f6c>] blk_put_request+0xe/0x14
[<0024d200>] __scsi_execute+0x124/0x174
[<0024d0dc>] __scsi_execute+0x0/0x174
[<00265d10>] sd_revalidate_disk+0xba/0x1f02
[<00265c56>] sd_revalidate_disk+0x0/0x1f02
[<0036ddf4>] strlen+0x0/0x22
[<00227ba0>] device_add+0x3da/0x604
[<0036ddf4>] strlen+0x0/0x22
[<00267e64>] sd_probe+0x30c/0x4b4
[<0002da44>] process_one_work+0x0/0x402
[<0022b978>] really_probe+0x226/0x354
[<0022bc34>] driver_probe_device+0xa4/0xf0
[<0002da44>] process_one_work+0x0/0x402
[<0022bcd0>] __driver_attach_async_helper+0x50/0x70
[<00035dae>] async_run_entry_fn+0x36/0x130
[<0002db88>] process_one_work+0x144/0x402
[<0002e1aa>] worker_thread+0x0/0x570
[<0002e29a>] worker_thread+0xf0/0x570
[<0002e1aa>] worker_thread+0x0/0x570
[<003768d8>] schedule+0x0/0xb8
[<0003f58c>] __init_waitqueue_head+0x0/0x12
[<00033e92>] kthread+0xc2/0xf6
[<000331e8>] kthread_parkme+0x0/0x4e
[<003768d8>] schedule+0x0/0xb8
[<00033dd0>] kthread+0x0/0xf6
[<00002c10>] ret_from_kernel_thread+0xc/0x14
Code: 0280 0006 0800 56c0 4400 0280 0000 00ff <52b4> 0c3a 082b 0006 0013 6706 2042 53a8 00c4 4ab9 0047 3374 6640 202d 000c 670c
Disabling lock debugging due to kernel taint
Avoid this by setting sg_tablesize = 1.
Link: https://lore.kernel.org/r/4567bcae94523b47d6f3b77450ba305823bca479.1572656814.git.fthain@telegraphics.com.au
Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
References: commit 68ab2d76e4be ("scsi: cxlflash: Set sg_tablesize to 1 instead of SG_NONE")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4f9f2d3d7a434b7f882b72550194c9278f4a3925 ]
The newer ibm,drc-info property is a condensed description of the old
ibm,drc-* properties (ie. names, types, indexes, and power-domains).
When matching a drc-index to a drc-name we need to verify that the
index is within the start and last drc-index range and map it to a
drc-name using the drc-name-prefix and logical index.
Fix the mapping by checking that the index is within the range of the
current drc-info entry, and build the name from the drc-name-prefix
concatenated with the starting drc-name-suffix value and the sequential
index obtained by subtracting ibm,my-drc-index from this entries
drc-start-index.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-10-git-send-email-tyreld@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0737686778c6dbe0908d684dd5b9c05b127526ba ]
The device tree is in big endian format and any properties directly
retrieved using OF helpers that don't explicitly byte swap should
be annotated. In particular there are several places where we grab
the opaque property value for the old ibm,drc-* properties and the
ibm,my-drc-index property.
Fix this for better static checking by annotating values we know to
explicitly big endian, and byte swap where appropriate.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-9-git-send-email-tyreld@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 52e2b0f16574afd082cff0f0e8567b2d9f68c033 ]
In the event that the partition is migrated to a platform with older
firmware that doesn't support the ibm,drc-info property the device
tree is modified to remove the ibm,drc-info property and replace it
with the older style ibm,drc-* properties for types, names, indexes,
and power-domains. One of the requirements of the drc-info firmware
feature is that the client is able to handle both the new property,
and old style properties at runtime. Therefore we can't rely on the
firmware feature alone to dictate which property is currently
present in the device tree.
Fix this short coming by checking explicitly for the ibm,drc-info
property, and falling back to the older ibm,drc-* properties if it
doesn't exist.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-6-git-send-email-tyreld@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cfcbae3895b86c390ede57b2a8f601dd5972b47b ]
In function __ufshcd_query_descriptor(), in the event of an error
happening, we directly goto out_unlock and forget to invaliate
hba->dev_cmd.query.descriptor pointer. This results in this pointer still
valid in ufshcd_copy_query_response() for other query requests which go
through ufshcd_exec_raw_upiu_cmd(). This will cause __memcpy() crash and
system hangs. Log as shown below:
Unable to handle kernel paging request at virtual address
ffff000012233c40
Mem abort info:
ESR = 0x96000047
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000047
CM = 0, WnR = 1
swapper pgtable: 4k pages, 48-bit VAs, pgdp = 0000000028cc735c
[ffff000012233c40] pgd=00000000bffff003, pud=00000000bfffe003,
pmd=00000000ba8b8003, pte=0000000000000000
Internal error: Oops: 96000047 [#2] PREEMPT SMP
...
Call trace:
__memcpy+0x74/0x180
ufshcd_issue_devman_upiu_cmd+0x250/0x3c0
ufshcd_exec_raw_upiu_cmd+0xfc/0x1a8
ufs_bsg_request+0x178/0x3b0
bsg_queue_rq+0xc0/0x118
blk_mq_dispatch_rq_list+0xb0/0x538
blk_mq_sched_dispatch_requests+0x18c/0x1d8
__blk_mq_run_hw_queue+0xb4/0x118
blk_mq_run_work_fn+0x28/0x38
process_one_work+0x1ec/0x470
worker_thread+0x48/0x458
kthread+0x130/0x138
ret_from_fork+0x10/0x1c
Code: 540000ab a8c12027 a88120c7 a8c12027 (a88120c7)
---[ end trace 793e1eb5dff69f2d ]---
note: kworker/0:2H[2054] exited with preempt_count 1
This patch is to move "descriptor = NULL" down to below the label
"out_unlock".
Fixes: d44a5f98bb49b2(ufs: query descriptor API)
Link: https://lore.kernel.org/r/20191112223436.27449-3-huobean@gmail.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9723c25f99aff0451cfe6392e1b9fdd99d0bf9f0 ]
The first entry of the ibm,drc-info property is an int encoded count
of the number of drc-info entries that follow. The "value" pointer
returned by of_prop_next_u32() is still pointing at the this value
when we call of_read_drc_info_cell(), but the helper function
expects that value to be pointing at the first element of an entry.
Fix up by incrementing the "value" pointer to point at the first
element of the first drc-info entry prior.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-5-git-send-email-tyreld@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 02f7e9f351a9de95577eafdc3bd413ed1c3b589f ]
When using this driver on a Blizzard 1260, there were failures whenever DMA
transfers from the SCSI bus to memory of 65535 bytes were followed by a DMA
transfer of 1 byte. This caused the byte at offset 65535 to be overwritten
with 0xff. The Blizzard hardware can't handle single byte DMA transfers.
Besides this issue, limiting the DMA length to something that is not a
multiple of the page size is very inefficient on most file systems.
It seems this limit was chosen because the DMA transfer counter of the ESP
by default is 16 bits wide, thus limiting the length to 65535 bytes.
However, the value 0 means 65536 bytes, which is handled by the ESP and the
Blizzard just fine. It is also the default maximum used by esp_scsi when
drivers don't provide their own dma_length_limit() function.
The limit of 65536 bytes can be used by all boards except the Fastlane. The
old driver used a limit of 65532 bytes (0xfffc), which is reintroduced in
this patch.
Fixes: b7ded0e8b0d1 ("scsi: zorro_esp: Limit DMA transfers to 65535 bytes")
Link: https://lore.kernel.org/r/20191112175523.23145-1-jongk@linux-m68k.org
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c6d59e0fe5b86cf273d6d744a6a9768c4ecc756 ]
Coverity reported the following:
*** CID 101747: Null pointer dereferences (FORWARD_NULL)
/drivers/scsi/lpfc/lpfc_els.c: 4439 in lpfc_cmpl_els_rsp()
4433 kfree(mp);
4434 }
4435 mempool_free(mbox, phba->mbox_mem_pool);
4436 }
4437 out:
4438 if (ndlp && NLP_CHK_NODE_ACT(ndlp)) {
vvv CID 101747: Null pointer dereferences (FORWARD_NULL)
vvv Dereferencing null pointer "shost".
4439 spin_lock_irq(shost->host_lock);
4440 ndlp->nlp_flag &= ~(NLP_ACC_REGLOGIN | NLP_RM_DFLT_RPI);
4441 spin_unlock_irq(shost->host_lock);
4442
4443 /* If the node is not being used by another discovery thread,
4444 * and we are sending a reject, we are done with it.
Fix by adding a check for non-null shost in line 4438.
The scenario when shost is set to null is when ndlp is null.
As such, the ndlp check present was sufficient. But better safe
than sorry so add the shost check.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 101747 ("Null pointer dereferences")
Fixes: 2e0fef85e098 ("[SCSI] lpfc: NPIV: split ports")
CC: James Bottomley <James.Bottomley@SteelEye.com>
CC: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
CC: linux-next@vger.kernel.org
Link: https://lore.kernel.org/r/20191111230401.12958-3-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 43f06a4c639de8ee89fc348a9a3ecd70320a04dd ]
input_mt_init_slots() may fail and we need to handle such failures.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 53aaaa5d9b1e95eb40e877fbffa6f964a8394bb7 ]
Add missing dma channels free calls in case of error during probe
and reorder the remove function so that dma channels are freed after
the i2c adapter is deleted.
Overall, reorder the remove function so that probe error handling order
and remove function order are same.
Fixes: 7ecc8cfde553 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f7aff1a93f52047739af31072de0ad8d149641f3 ]
Since commit 7723f4c5ecdb ("driver core: platform: Add an error message
to platform_get_irq*()"), platform_get_irq_byname() displays an error
when the IRQ isn't found. Since the SMMUv3 driver uses that function to
query which interrupt method is available, the message is now displayed
during boot for any SMMUv3 that doesn't implement the combined
interrupt, or that implements MSIs.
[ 20.700337] arm-smmu-v3 arm-smmu-v3.7.auto: IRQ combined not found
[ 20.706508] arm-smmu-v3 arm-smmu-v3.7.auto: IRQ eventq not found
[ 20.712503] arm-smmu-v3 arm-smmu-v3.7.auto: IRQ priq not found
[ 20.718325] arm-smmu-v3 arm-smmu-v3.7.auto: IRQ gerror not found
Use platform_get_irq_byname_optional() to avoid displaying a spurious
error.
Fixes: 7723f4c5ecdb ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 52ecc87642f273a599c9913b29fd179c13de457b ]
If we cannot create the IRQ domain, the driver should fail to probe
instead of succeeding with just a warning message.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1570015525-27018-3-git-send-email-zhouyanjie@zoho.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 27eebb60357ed5aa6659442f92907c0f7368d6ae ]
If the 'brcm,irq-can-wake' property is specified, make sure we also
enable the corresponding parent interrupt we are attached to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191024201415.23454-4-f.fainelli@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fc59462c5ce60da119568fac325c92fc6b7c6175 ]
For an external clock source, which is gated via a GPIO, the
rate change should typically be propagated to the parent clock.
The situation where we are requiring this propagation, is when an
external clock is connected to override an internal clock (which typically
has a fixed rate). The external clock can have a different rate than the
internal one, and may also be variable, thus requiring the rate
propagation.
This rate change wasn't propagated until now, and it's unclear about cases
where this shouldn't be propagated. Thus, it's unclear whether this is
fixing a bug, or extending the current driver behavior. Also, it's unsure
about whether this may break any existing setups; in the case that it does,
a device-tree property may be added to disable this flag.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lkml.kernel.org/r/20191108071718.17985-1-alexandru.ardelean@analog.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit efd164b5520afd6fb2883b68e0d408a7de29c491 ]
Some RCGs (the gfx_3d_src_clk in msm8998 for example) are basically just
some constant ratio from the input across the entire frequency range. It
would be great if we could specify the frequency table as a single entry
constant ratio instead of a long list, ie:
{ .src = P_GPUPLL0_OUT_EVEN, .pre_div = 3 },
{ }
So, lets support that.
We need to fix a corner case in qcom_find_freq() where if the freq table
is non-null, but has no frequencies, we end up returning an "entry" before
the table array, which is bad. Then, we need ignore the freq from the
table, and instead base everything on the requested freq.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lkml.kernel.org/r/20191031185715.15504-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ba1d366de261981c0dd04fac44d2ce3a5eba2eaa ]
When MSM8998 support was added, and analysis was done to determine what
clocks would be consumed. That analysis had a flaw, which caused the
pnoc to be skipped. The pnoc clock needs to be on to access the uart
for the console. The clock is on from boot, but has no consumer votes
in the RPM. When we attempt to boot the modem, it causes the RPM to
turn off pnoc, which kills our access to the console and causes CPU hangs.
We need pnoc to be defined, so that clk_smd_rpm_handoff() will put in
an implicit vote for linux and prevent issues when booting modem.
Hopefully pnoc can be consumed by the interconnect framework in future
so that Linux can rely on explicit votes.
Fixes: 6131dc81211c ("clk: qcom: smd: Add support for MSM8998 rpm clocks")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lkml.kernel.org/r/20191107190615.5656-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7cfd5639d99bec0d27af089d0c8c114330e43a72 ]
If the driver receives a login that is later then LOGO'd by the remote port
(aka ndlp), the driver, upon the completion of the LOGO ACC transmission,
will logout the node and unregister the rpi that is being used for the
node. As part of the unreg, the node's rpi value is replaced by the
LPFC_RPI_ALLOC_ERROR value. If the port is subsequently offlined, the
offline walks the nodes and ensures they are logged out, which possibly
entails unreg'ing their rpi values. This path does not validate the node's
rpi value, thus doesn't detect that it has been unreg'd already. The
replaced rpi value is then used when accessing the rpi bitmask array which
tracks active rpi values. As the LPFC_RPI_ALLOC_ERROR value is not a valid
index for the bitmask, it may fault the system.
Revise the rpi release code to detect when the rpi value is the replaced
RPI_ALLOC_ERROR value and ignore further release steps.
Link: https://lore.kernel.org/r/20191105005708.7399-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2332e6e475b016e2026763f51333f84e2e6c57a3 ]
During heavy RCN activity and log_verbose = 0 we see these messages:
2754 PRLI failure DID:521245 Status:x9/xb2c00, data: x0
0231 RSCN timeout Data: x0 x3
0230 Unexpected timeout, hba link state x5
This is due to delayed RSCN activity.
Correct by avoiding the timeout thus the messages by restarting the
discovery timeout whenever an rscn is received.
Filter PRLI responses such that severity depends on whether expected for
the configuration or not. For example, PRLI errors on a fabric will be
informational (they are expected), but Point-to-Point errors are not
necessarily expected so they are raised to an error level.
Link: https://lore.kernel.org/r/20191105005708.7399-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f6b8540f40201bff91062dd64db8e29e4ddaaa9d ]
According to SBC-2 a TRANSFER LENGTH field of zero means that 256 logical
blocks must be transferred. Make the SCSI tracing code follow SBC-2.
Fixes: bf8162354233 ("[SCSI] add scsi trace core functions and put trace points")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Link: https://lore.kernel.org/r/20191105215553.185018-1-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4411464d6f8b5e5759637235a6f2b2a85c2be0f1 ]
If a hardware-specific driver does not provide a name, the timer-of core
falls back to device_node.name. Due to generic DT node naming policies,
that name is almost always "timer", and thus doesn't identify the actual
timer used.
Fix this by using device_node.full_name instead, which includes the unit
addrees.
Example impact on /proc/timer_list:
-Clock Event Device: timer
+Clock Event Device: timer@fcfec400
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016144747.29538-3-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e001f6a4cc73cd06fc7b8c633bc4906c33dd8ad ]
asm9260_timer_init misses a check for of_clk_get.
Add a check for it and print errors like other clocksource drivers.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016124330.22211-1-hslester96@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5f820ed52371b4f5d8c43c93f03408d0dbc01e5b ]
The NETDEV_CHANGENAME code is not "unneeded" like it is stated in commit
4cb6560514fa ("leds: trigger: netdev: fix refcnt leak on interface
rename").
The event was accidentally misinterpreted equivalent to
NETDEV_UNREGISTER, but should be equivalent to NETDEV_REGISTER.
This was the case in the original code from the openwrt project.
Otherwise, you are unable to set netdev led triggers for (non-existent)
netdevices, which has to be renamed. This is the case, for example, for
ppp interfaces in openwrt.
Fixes: 06f502f57d0d ("leds: trigger: Introduce a NETDEV trigger")
Fixes: 4cb6560514fa ("leds: trigger: netdev: fix refcnt leak on interface rename")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fc7b5028f2627133c7c18734715a08829eab4d1f ]
an30259a_probe misses a check for devm_regmap_init_i2c and may cause
problems.
Add a check and print errors like other leds drivers.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 396128d2ffcba6e1954cfdc9a89293ff79cbfd7c ]
Instead use devm_regulator_get_optional since the regulator
is optional and check for errors.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 41814c4eadf8a791b6d07114f96e7e120e59555c ]
platform_get_irq_byname() might return -errno which later would be cast
to an unsigned int and used in IRQ handling code leading to usage of
wrong ID and errors about wrong irq_base.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Peng Ma <peng.ma@nxp.com>
Tested-by: Peng Ma <peng.ma@nxp.com>
Link: https://lore.kernel.org/r/20191004150826.6656-1-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit efd7bb08a762d4f6322054c6824bd942971ac563 ]
We should not be putting the chip into reset while interrupts are enabled
and ISR may be running. Fix this by installing a custom devm action and
powering off the device/resetting GPIO line from there. This ensures proper
ordering.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cabe7c10c97a0857a9fb14b6c772ab784947995d ]
Although if the debugfs initialization fails, we will delete the debugfs
folder of hisi_sas, but we did not consider the scenario where debugfs was
successfully initialized, but the probe failed for other reasons. We found
out that hisi_sas folder is still remain after the probe failed.
When probe fail, we should delete debugfs folder to avoid the above issue.
Link: https://lore.kernel.org/r/1571926105-74636-18-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 550c0d89d52d3bec5c299f69b4ed5d2ee6b8a9a6 ]
For IOs from upper layer, preemption may be disabled as it may be called by
function __blk_mq_delay_run_hw_queue which will call get_cpu() (it disables
preemption). So if flags HISI_SAS_REJECT_CMD_BIT is set in function
hisi_sas_task_exec(), it may disable preempt twice after down() and up()
which will cause following call trace:
BUG: scheduling while atomic: fio/60373/0x00000002
Call trace:
dump_backtrace+0x0/0x150
show_stack+0x24/0x30
dump_stack+0xa0/0xc4
__schedule_bug+0x68/0x88
__schedule+0x4b8/0x548
schedule+0x40/0xd0
schedule_timeout+0x200/0x378
__down+0x78/0xc8
down+0x54/0x70
hisi_sas_task_exec.isra.10+0x598/0x8d8 [hisi_sas_main]
hisi_sas_queue_command+0x28/0x38 [hisi_sas_main]
sas_queuecommand+0x168/0x1b0 [libsas]
scsi_queue_rq+0x2ac/0x980
blk_mq_dispatch_rq_list+0xb0/0x550
blk_mq_do_dispatch_sched+0x6c/0x110
blk_mq_sched_dispatch_requests+0x114/0x1d8
__blk_mq_run_hw_queue+0xb8/0x130
__blk_mq_delay_run_hw_queue+0x1c0/0x220
blk_mq_run_hw_queue+0xb0/0x128
blk_mq_sched_insert_requests+0xdc/0x208
blk_mq_flush_plug_list+0x1b4/0x3a0
blk_flush_plug_list+0xdc/0x110
blk_finish_plug+0x3c/0x50
blkdev_direct_IO+0x404/0x550
generic_file_read_iter+0x9c/0x848
blkdev_read_iter+0x50/0x78
aio_read+0xc8/0x170
io_submit_one+0x1fc/0x8d8
__arm64_sys_io_submit+0xdc/0x280
el0_svc_common.constprop.0+0xe0/0x1e0
el0_svc_handler+0x34/0x90
el0_svc+0x10/0x14
...
To solve the issue, check preemptible() to avoid disabling preempt multiple
when flag HISI_SAS_REJECT_CMD_BIT is set.
Link: https://lore.kernel.org/r/1571926105-74636-5-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d6c9b31ac3064fbedf8961f120a4c117daa59932 ]
These are called with IRQs disabled from csio_mgmt_tmo_handler() so we
can't call spin_unlock_irq() or it will enable IRQs prematurely.
Fixes: a3667aaed569 ("[SCSI] csiostor: Chelsio FCoE offload driver")
Link: https://lore.kernel.org/r/20191019085913.GA14245@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit feff8b3d84d3d9570f893b4d83e5eab6693d6a52 ]
When operating in private loop mode, PLOGI exchanges are racing and the
driver tries to abort it's PLOGI. But the PLOGI abort ends up terminating
the login with the other end causing the other end to abort its PLOGI as
well. Discovery never fully completes.
Fix by disabling the PLOGI abort when private loop and letting the state
machine play out.
Link: https://lore.kernel.org/r/20191018211832.7917-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 91a52b617cdb8bf6d298892101c061d438b84a19 ]
In lpfc_abort_handler, the lock acquire order is hbalock (irqsave),
buf_lock (irq) and ring_lock (irq). The issue is that in two places the
locks are released out of order - the buf_lock and the hbalock - resulting
in the cpu preemption/lock flags getting restored out of order and
deadlocking the cpu.
Fix the unlock order by fully releasing the hbalocks as well.
CC: Zhangguanghui <zhang.guanghui@h3c.com>
Link: https://lore.kernel.org/r/20191018211832.7917-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9cef2a7955f2754257a7cddedec16edae7b587d0 ]
RFC 2307 states:
For CHAP [RFC1994], in the first step, the initiator MUST send:
CHAP_A=<A1,A2...>
Where A1,A2... are proposed algorithms, in order of preference.
...
For the Algorithm, as stated in [RFC1994], one value is required to
be implemented:
5 (CHAP with MD5)
LIO currently checks for this value by only comparing a single byte in
the tokenized Algorithm string, which means that any value starting with
a '5' (e.g. "55") is interpreted as "CHAP with MD5". Fix this by
comparing the entire tokenized string.
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Link: https://lore.kernel.org/r/20190912095547.22427-2-ddiss@suse.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a631a5a0f7d4a4a24dba8587d5d9152be0871cc ]
Whenever we reset the channel, we need to clear desc_pendingcount
along with desc_submitcount. Otherwise when a new transaction is
submitted, the irq coalesce level could be programmed to an incorrect
value in the axidma case.
This behavior can be observed when terminating pending transactions
with xilinx_dma_terminate_all() and then submitting new transactions
without releasing and requesting the channel.
Signed-off-by: Nicholas Graumann <nick.graumann@gmail.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1571150904-3988-8-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 96d3ab802e4930a29a33934373157d6dff1b2c7e ]
Page tables that reside in physical memory beyond the 4 GiB boundary are
currently not working properly. The reason is that when the physical
address for page directory entries is read, it gets truncated at 32 bits
and can cause crashes when passing that address to the DMA API.
Fix this by first casting the PDE value to a dma_addr_t and then using
the page frame number mask for the SMMU instance to mask out the invalid
bits, which are typically used for mapping attributes, etc.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 42bb97b80f2e3bf592e3e99d109b67309aa1b30e ]
IOMMU domain resource life is well-defined, managed
by .domain_alloc and .domain_free.
Therefore, domain-specific resources shouldn't be tied to
the device life, but instead to its domain.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 60d15095336cfb56dce5c7767ed3b8c6c1cf79a3 ]
We have added polled mode to the normal input devices with the intent of
retiring input_polled_dev. This converts peaq-wmi driver to use the
polling mode of standard input devices and removes dependency on
INPUT_POLLDEV.
Because the new polling coded does not allow peeking inside the poller
structure to get the poll interval, we change the "debounce" process to
operate on the time basis, instead of counting events.
We also fix error handling during initialization, as previously we leaked
input device structure when we failed to register it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 463fa44eec2fef50d111ed0199cf593235065c04 ]
Across suspend and resume, we are seeing error messages like the following:
atmel_mxt_ts i2c-PRP0001:00: __mxt_read_reg: i2c transfer failed (-121)
atmel_mxt_ts i2c-PRP0001:00: Failed to read T44 and T5 (-121)
This occurs because the driver leaves its IRQ enabled. Upon resume, there
is an IRQ pending, but the interrupt is serviced before both the driver and
the underlying I2C bus have been resumed. This causes EREMOTEIO errors.
Disable the IRQ in suspend, and re-enable it on resume. If there are cases
where the driver enters suspend with interrupts disabled, that's a bug we
should fix separately.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 15498dc1a55b7aaea4b51ff03e3ff0f662e73f44 ]
After study, it was determined there was a double free of a CT iocb during
execution of lpfc_offline_prep and lpfc_offline. The prep routine issued
an abort for some CT iocbs, but the aborts did not complete fast enough for
a subsequent routine that waits for completion. Thus the driver proceeded
to lpfc_offline, which releases any pending iocbs. Unfortunately, the
completions for the aborts were then received which re-released the ct
iocbs.
Turns out the issue for why the aborts didn't complete fast enough was not
their time on the wire/in the adapter. It was the lpfc_work_done routine,
which requires the adapter state to be UP before it calls
lpfc_sli_handle_slow_ring_event() to process the completions. The issue is
the prep routine takes the link down as part of it's processing.
To fix, the following was performed:
- Prevent the offline routine from releasing iocbs that have had aborts
issued on them. Defer to the abort completions. Also means the driver
fully waits for the completions. Given this change, the recognition of
"driver-generated" status which then releases the iocb is no longer
valid. As such, the change made in the commit 296012285c90 is reverted.
As recognition of "driver-generated" status is no longer valid, this
patch reverts the changes made in
commit 296012285c90 ("scsi: lpfc: Fix leak of ELS completions on adapter reset")
- Modify lpfc_work_done to allow slow path completions so that the abort
completions aren't ignored.
- Updated the fdmi path to recognize a CT request that fails due to the
port being unusable. This stops FDMI retries. FDMI will be restarted on
next link up.
Link: https://lore.kernel.org/r/20190922035906.10977-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c8f3d144004dd3f471ffd414690d15a005e4acd6 ]
On some of i.MX SoCs like i.MX8QXP, there is ONLY one IRQ for each
GPIO bank, so it is better to check the IRQ count before getting
second IRQ to avoid below error message during probe:
[ 1.070908] gpio-mxc 5d080000.gpio: IRQ index 1 not found
[ 1.077420] gpio-mxc 5d090000.gpio: IRQ index 1 not found
[ 1.083766] gpio-mxc 5d0a0000.gpio: IRQ index 1 not found
[ 1.090122] gpio-mxc 5d0b0000.gpio: IRQ index 1 not found
[ 1.096470] gpio-mxc 5d0c0000.gpio: IRQ index 1 not found
[ 1.102804] gpio-mxc 5d0d0000.gpio: IRQ index 1 not found
[ 1.109144] gpio-mxc 5d0e0000.gpio: IRQ index 1 not found
[ 1.115475] gpio-mxc 5d0f0000.gpio: IRQ index 1 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 77fd4f2c88bf83205a21f9ca49fdcc0c7868dba9 ]
If any faulty application issues an NVMe Encapsulated commands to HBA which
doesn't support NVMe protocol then driver should return the command as
invalid with the following message.
"HBA doesn't support NVMe. Rejecting NVMe Encapsulated request."
Otherwise below page fault kernel panic will be observed while building the
PRPs as there is no PRP pools allocated for the HBA which doesn't support
NVMe drives.
RIP: 0010:_base_build_nvme_prp+0x3b/0xf0 [mpt3sas]
Call Trace:
_ctl_do_mpt_command+0x931/0x1120 [mpt3sas]
_ctl_ioctl_main.isra.11+0xa28/0x11e0 [mpt3sas]
? prepare_to_wait+0xb0/0xb0
? tty_ldisc_deref+0x16/0x20
_ctl_ioctl+0x1a/0x20 [mpt3sas]
do_vfs_ioctl+0xaa/0x620
? vfs_read+0x117/0x140
ksys_ioctl+0x67/0x90
__x64_sys_ioctl+0x1a/0x20
do_syscall_64+0x60/0x190
entry_SYSCALL_64_after_hwframe+0x44/0xa9
[mkp: tweaked error string]
Link: https://lore.kernel.org/r/1568379890-18347-12-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 07b8582430370097238b589f4e24da7613ca6dd3 ]
Symptoms were seen of the driver not having valid data for mailbox
commands. After debugging, the following sequence was found:
The driver maintains a port-wide pointer of the mailbox command that is
currently in execution. Once finished, the port-wide pointer is cleared
(done in lpfc_sli4_mq_release()). The next mailbox command issued will set
the next pointer and so on.
The mailbox response data is only copied if there is a valid port-wide
pointer.
In the failing case, it was seen that a new mailbox command was being
attempted in parallel with the completion. The parallel path was seeing
the mailbox no long in use (flag check under lock) and thus set the port
pointer. The completion path had cleared the active flag under lock, but
had not touched the port pointer. The port pointer is cleared after the
lock is released. In this case, the completion path cleared the just-set
value by the parallel path.
Fix by making the calls that clear mbox state/port pointer while under
lock. Also slightly cleaned up the error path.
Link: https://lore.kernel.org/r/20190922035906.10977-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 782b281883caf70289ba6a186af29441a117d23e ]
When user issues diag register command from application with required size,
and if driver unable to allocate the memory, then it will fail the register
command. While failing the register command, driver is not currently
clearing MPT3_CMD_PENDING bit in ctl_cmds.status variable which was set
before trying to allocate the memory. As this bit is set, subsequent
register command will be failed with BUSY status even when user wants to
register the trace buffer will less memory.
Clear MPT3_CMD_PENDING bit in ctl_cmds.status before returning the diag
register command with no memory status.
Link: https://lore.kernel.org/r/1568379890-18347-4-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|