| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 5a3ba99b62d8486de0316334e72ac620d4b94fdd upstream.
The sparse tool complains as follows:
drivers/char/ipmi/ipmi_msghandler.c:194:25: warning:
symbol 'remove_work_wq' was not declared. Should it be static?
This symbol is not used outside of ipmi_msghandler.c, so
marks it static.
Fixes: 1d49eb91e86e ("ipmi: Move remove_work to dedicated workqueue")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Message-Id: <20211123083618.2366808-1-weiyongjun1@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5283dd677e52af9db6fe6ad11b2f12220d519d0c upstream.
In some very rare cases the init flow may fail. In many cases, this is
recoverable, so we can retry. Implement a loop to retry two more times
after the first attempt failed.
This can happen in two different situations, namely during probe and
during mac80211 start. For the first case, a simple loop is enough.
For the second case, we need to add a flag to prevent mac80211 from
trying to restart it as well, leaving full control with the driver.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20211110150132.57514296ecab.I52a0411774b700bdc7dedb124d8b59bf99456eb2@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bb1201d4b38ec67bd9a871cf86b0cc10f28b15b5 upstream.
Have pericom_do_set_divisor() use the uartclk instead of a hard coded
value to work with different speed crystals. Tested with 14.7456 and 24
MHz crystals.
Have pericom_do_set_divisor() always calculate the divisor rather than
call serial8250_do_set_divisor() for rates below baud_base.
Do not write registers or call serial8250_do_set_divisor() if valid
divisors could not be found.
Fixes: 6bf4e42f1d19 ("serial: 8250: Add support for higher baud rates to Pericom chips")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c525c5d2437f93520388920baac6d9340c65d239 upstream.
Fix error in table for PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S that caused it
and PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4 to be missing their fourth port.
Fixes: 78d3820b9bd3 ("serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 00de977f9e0aa9760d9a79d1e41ff780f74e3424 upstream.
Commit 761ed4a94582 ("tty: serial_core: convert uart_close to use
tty_port_close") converted serial core to use tty_port_close() but
failed to notice that the transmit buffer still needs to be freed on
final close.
Not freeing the transmit buffer means that the buffer is no longer
cleared on next open so that any ioctl() waiting for the buffer to drain
might wait indefinitely (e.g. on termios changes) or that stale data can
end up being transmitted in case tx is restarted.
Furthermore, the buffer of any port that has been opened would leak on
driver unbind.
Note that the port lock is held when clearing the buffer pointer due to
the ldisc race worked around by commit a5ba1d95e46e ("uart: fix race
between uart_put_char() and uart_shutdown()").
Also note that the tty-port shutdown() callback is not called for
console ports so it is not strictly necessary to free the buffer page
after releasing the lock (cf. d72402145ace ("tty/serial: do not free
trasnmit buffer page under port lock")).
Link: https://lore.kernel.org/r/319321886d97c456203d5c6a576a5480d07c3478.1635781688.git.baruch@tkos.co.il
Fixes: 761ed4a94582 ("tty: serial_core: convert uart_close to use tty_port_close")
Cc: stable@vger.kernel.org # 4.9
Cc: Rob Herring <robh@kernel.org>
Reported-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211108085431.12637-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ac442a077acf9a6bf1db4320ec0c3f303be092b3 upstream.
The document 'ACPI for Arm Components 1.0' defines the following
_HID mappings:
-'Prime cell UART (PL011)': ARMH0011
-'SBSA UART': ARMHB000
Use the sbsa-uart driver when a device is described with
the 'ARMHB000' _HID.
Note:
PL011 devices currently use the sbsa-uart driver instead of the
uart-pl011 driver. Indeed, PL011 devices are not bound to a clock
in ACPI. It is not possible to change their baudrate.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pierre Gondois <Pierre.Gondois@arm.com>
Link: https://lore.kernel.org/r/20211109172248.19061-1-Pierre.Gondois@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7492ffc90fa126afb67d4392d56cb4134780194a upstream.
The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of
setup, it is often sharing a serial device with the normal system console.
This is usually no problem because the polling helpers can consume input
values directly (when in kgdb context) and the normal Linux handlers can
only consume new input values after kgdb switched back.
This is not true anymore when RX DMA is enabled for UARTDM controllers.
Single input values can no longer be received correctly. Instead following
seems to happen:
* on 1. input, some old input is read (continuously)
* on 2. input, two old inputs are read (continuously)
* on 3. input, three old input values are read (continuously)
* on 4. input, 4 previous inputs are received
This repeats then for each group of 4 input values.
This behavior changes slightly depending on what state the controller was
when the first input was received. But this makes working with kgdb
basically impossible because control messages are always corrupted when
kgdboc tries to parse them.
RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid
these kind of problems. No such problem was noticed for TX DMA.
Fixes: 99693945013a ("tty: serial: msm: Add RX DMA support")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20211113121050.7266-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fbcd13df1e78eb2ba83a3c160eefe2d6f574beaf upstream.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
This change makes TCPM to wait in SNK_DEBOUNCED state until
CC1 and CC2 pins is SNK.Open for at least tPDDebounce. Previously,
TCPM resets the port if vbus is not present in PD_T_PS_SOURCE_ON.
This causes TCPM to loop continuously when connected to a
faulty power source that does not present vbus. Waiting in
SNK_DEBOUNCED also ensures that TCPM is adherant to
"4.5.2.2.4.2 Exiting from AttachWait.SNK State" requirements.
[ 6169.280751] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 6169.280759] state change TOGGLING -> SNK_ATTACH_WAIT [rev2 NONE_AMS]
[ 6169.280771] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev2 NONE_AMS]
[ 6169.282427] CC1: 0 -> 0, CC2: 5 -> 5 [state SNK_ATTACH_WAIT, polarity 0, connected]
[ 6169.450825] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[ 6169.450834] pending state change SNK_DEBOUNCED -> PORT_RESET @ 480 ms [rev2 NONE_AMS]
[ 6169.930892] state change SNK_DEBOUNCED -> PORT_RESET [delayed 480 ms]
[ 6169.931296] disable vbus discharge ret:0
[ 6169.931301] Setting usb_comm capable false
[ 6169.932783] Setting voltage/current limit 0 mV 0 mA
[ 6169.932802] polarity 0
[ 6169.933706] Requesting mux state 0, usb-role 0, orientation 0
[ 6169.936689] cc:=0
[ 6169.936812] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev2 NONE_AMS]
[ 6169.937157] CC1: 0 -> 0, CC2: 5 -> 0 [state PORT_RESET, polarity 0, disconnected]
[ 6170.036880] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 6170.036890] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev2 NONE_AMS]
[ 6170.036896] Start toggling
[ 6170.041412] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 6170.042973] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 6170.042976] state change TOGGLING -> SNK_ATTACH_WAIT [rev2 NONE_AMS]
[ 6170.042981] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev2 NONE_AMS]
[ 6170.213014] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[ 6170.213019] pending state change SNK_DEBOUNCED -> PORT_RESET @ 480 ms [rev2 NONE_AMS]
[ 6170.693068] state change SNK_DEBOUNCED -> PORT_RESET [delayed 480 ms]
[ 6170.693304] disable vbus discharge ret:0
[ 6170.693308] Setting usb_comm capable false
[ 6170.695193] Setting voltage/current limit 0 mV 0 mA
[ 6170.695210] polarity 0
[ 6170.695990] Requesting mux state 0, usb-role 0, orientation 0
[ 6170.701896] cc:=0
[ 6170.702181] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev2 NONE_AMS]
[ 6170.703343] CC1: 0 -> 0, CC2: 5 -> 0 [state PORT_RESET, polarity 0, disconnected]
Fixes: f0690a25a140b8 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20211130001825.3142830-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2a004037c3c6afd36d40c384d2905f47cd51c57 upstream.
This is another branded 8153 device that doesn't work well with LPM:
r8152 2-2.1:1.0 enp0s13f0u2u1: Stop submitting intr, status -71
Disable LPM to resolve the issue.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211127090546.52072-1-olebowle@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09f736aa95476631227d2dc0e6b9aeee1ad7ed58 upstream.
Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Fixes: ff0e50d3564f ("xhci: Fix command ring pointer corruption while aborting a command")
Cc: stable@vger.kernel.org
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3dfac26e2ef29ff2abc2a75aa4cd48fce25a2c4b upstream.
Fix a division by zero in `vgacon_resize' with a backtrace like:
vgacon_resize
vc_do_resize
vgacon_init
do_bind_con_driver
do_unbind_con_driver
fbcon_fb_unbind
do_unregister_framebuffer
do_register_framebuffer
register_framebuffer
__drm_fb_helper_initial_config_and_unlock
drm_helper_hpd_irq_event
dw_hdmi_irq
irq_thread
kthread
caused by `c->vc_cell_height' not having been initialized. This has
only started to trigger with commit 860dafa90259 ("vt: Fix character
height handling with VT_RESIZEX"), however the ultimate offender is
commit 50ec42edd978 ("[PATCH] Detaching fbcon: fix vgacon to allow
retaking of the console").
Said commit has added a call to `vc_resize' whenever `vgacon_init' is
called with the `init' argument set to 0, which did not happen before.
And the call is made before a key vgacon boot parameter retrieved in
`vgacon_startup' has been propagated in `vgacon_init' for `vc_resize' to
use to the console structure being worked on. Previously the parameter
was `c->vc_font.height' and now it is `c->vc_cell_height'.
In this particular scenario the registration of fbcon has failed and vt
resorts to vgacon. Now fbcon does have initialized `c->vc_font.height'
somehow, unlike `c->vc_cell_height', which is why this code did not
crash before, but either way the boot parameters should have been copied
to the console structure ahead of the call to `vc_resize' rather than
afterwards, so that first the call has a chance to use them and second
they do not change the console structure to something possibly different
from what was used by `vc_resize'.
Move the propagation of the vgacon boot parameters ahead of the call to
`vc_resize' then. Adjust the comment accordingly.
Fixes: 50ec42edd978 ("[PATCH] Detaching fbcon: fix vgacon to allow retaking of the console")
Cc: stable@vger.kernel.org # v2.6.18+
Reported-by: Wim Osterholt <wim@djo.tudelft.nl>
Reported-by: Pavel V. Panteleev <panteleev_p@mcst.ru>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2110252317110.58149@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4840d537c2c6b1189d4de16ee0f4820e069dcea upstream.
In particular, we need to ensure all the necessary blocks are switched
to 64b mode (a5xx+) otherwise the high bits of the address of the BO to
snapshot state into will be ignored, resulting in:
*** gpu fault: ttbr0=0000000000000000 iova=0000000000012000 dir=READ type=TRANSLATION source=CP (0,0,0,0)
platform 506a000.gmu: [drm:a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set BOOT_SLUMBER: 0x0
Fixes: 4f776f4511c7 ("drm/msm/gpu: Convert the GPU show function to use the GPU state")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20211108180122.487859-1-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b83f5ac7d922e69a109261f5f940eebbd4e514c4 upstream.
'bitmap_fill()' fills a bitmap one 'long' at a time.
It is likely that an exact number of bits is expected.
Use 'bitmap_set()' instead in order not to set unexpected bits.
Fixes: e531f76757eb ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
is available
commit 817b653160db9852d5a0498a31f047e18ce27e5b upstream.
On most systems request for IRQ 0 will fail, phylib will print an error message
and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ
is available.
Fixes: cc89c323a30e ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit addad7643142f500080417dd7272f49b7a185570 upstream.
In mlx4_en_try_alloc_resources(), mlx4_en_copy_priv() is called and
tmp->tx_cq will be freed on the error path of mlx4_en_copy_priv().
After that mlx4_en_alloc_resources() is called and there is a dereference
of &tmp->tx_cq[t][i] in mlx4_en_alloc_resources(), which could lead to
a use after free problem on failure of mlx4_en_copy_priv().
Fix this bug by adding a check of mlx4_en_copy_priv()
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_MLX4_EN=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: ec25bc04ed8e ("net/mlx4_en: Add resilience in low memory systems")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20211130164438.190591-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e2dabc4f7e7b60299c20a36d6a7b24ed9bf8e572 upstream.
In qlcnic_83xx_add_rings(), the indirect function of
ahw->hw_ops->alloc_mbx_args will be called to allocate memory for
cmd.req.arg, and there is a dereference of it in qlcnic_83xx_add_rings(),
which could lead to a NULL pointer dereference on failure of the
indirect function like qlcnic_83xx_alloc_mbx_args().
Fix this bug by adding a check of alloc_mbx_args(), this patch
imitates the logic of mbx_cmd()'s failure handling.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_QLCNIC=m show no new warnings, and our
static analyzer no longer warns about this code.
Fixes: 7f9664525f9c ("qlcnic: 83xx memory map and HW access routine")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130110848.109026-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b0f38e15979fa8851e88e8aa371367f264e7b6e9 upstream.
Fix section mismatch warnings in xtsonic. The first one appears to be
bogus and after fixing the second one, the first one is gone.
WARNING: modpost: vmlinux.o(.text+0x529adc): Section mismatch in reference from the function sonic_get_stats() to the function .init.text:set_reset_devices()
The function sonic_get_stats() references
the function __init set_reset_devices().
This is often because sonic_get_stats lacks a __init
annotation or the annotation of set_reset_devices is wrong.
WARNING: modpost: vmlinux.o(.text+0x529b3b): Section mismatch in reference from the function xtsonic_probe() to the function .init.text:sonic_probe1()
The function xtsonic_probe() references
the function __init sonic_probe1().
This is often because xtsonic_probe lacks a __init
annotation or the annotation of sonic_probe1 is wrong.
Fixes: 74f2a5f0ef64 ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20211130063947.7529-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b12764695c3fcade145890b67f82f8b139174cc7 upstream.
CBUS transfers have always been atomic, but after commit 63b96983a5dd
("i2c: core: introduce callbacks for atomic transfers") we started to see
warnings during e.g. poweroff as the atomic callback is not explicitly set.
Fix that.
Fixes the following WARNING seen during Nokia N810 power down:
[ 786.570617] reboot: Power down
[ 786.573913] ------------[ cut here ]------------
[ 786.578826] WARNING: CPU: 0 PID: 672 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x110
[ 786.587799] No atomic I2C transfer handler for 'i2c-2'
Fixes: 63b96983a5dd ("i2c: core: introduce callbacks for atomic transfers")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 31b90a95ccbbb4b628578ac17e3b3cc8eeacfe31 upstream.
In case of receiving a NACK, the dma transfer should be stopped
to avoid feeding data into the FIFO.
Also ensure to properly return the proper error code and avoid
waiting for the end of the dma completion in case of
error happening during the transmission.
Fixes: 7ecc8cfde553 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b933d1faf8fa30d16171bcff404e39c41b2a7c84 upstream.
When getting an access timeout, ensure that the bus is in a proper
state prior to returning the error.
Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c21d02ca469574d2082379db52d1a27b99eed0c upstream.
While handling an error during transfer (ex: NACK), it could
happen that the driver has already written data into TXDR
before the transfer get stopped.
This commit add TXDR Flush after end of transfer in case of error to
avoid sending a wrong data on any other slave upon next transfer.
Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f48394cf1f3e8486591ad98c11cdadb8f1ef2ad upstream.
Trying to remove the fsl-sata module in the PPC64 GNU/Linux
leads to the following warning:
------------[ cut here ]------------
remove_proc_entry: removing non-empty directory 'irq/69',
leaking at least 'fsl-sata[ff0221000.sata]'
WARNING: CPU: 3 PID: 1048 at fs/proc/generic.c:722
.remove_proc_entry+0x20c/0x220
IRQMASK: 0
NIP [c00000000033826c] .remove_proc_entry+0x20c/0x220
LR [c000000000338268] .remove_proc_entry+0x208/0x220
Call Trace:
.remove_proc_entry+0x208/0x220 (unreliable)
.unregister_irq_proc+0x104/0x140
.free_desc+0x44/0xb0
.irq_free_descs+0x9c/0xf0
.irq_dispose_mapping+0x64/0xa0
.sata_fsl_remove+0x58/0xa0 [sata_fsl]
.platform_drv_remove+0x40/0x90
.device_release_driver_internal+0x160/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
---[ end trace 0ea876d4076908f5 ]---
The driver creates the mapping by calling irq_of_parse_and_map(),
so it also has to dispose the mapping. But the easy way out is to
simply use platform_get_irq() instead of irq_of_parse_map(). Also
we should adapt return value checking and propagate error values.
In this case the mapping is not managed by the device but by
the of core, so the device has not to dispose the mapping.
Fixes: faf0b2e5afe7 ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6c8ad7e8cf29eb55836e7a0215f967746ab2b504 upstream.
When the `rmmod sata_fsl.ko` command is executed in the PPC64 GNU/Linux,
a bug is reported:
==================================================================
BUG: Unable to handle kernel data access on read at 0x80000800805b502c
Oops: Kernel access of bad area, sig: 11 [#1]
NIP [c0000000000388a4] .ioread32+0x4/0x20
LR [80000000000c6034] .sata_fsl_port_stop+0x44/0xe0 [sata_fsl]
Call Trace:
.free_irq+0x1c/0x4e0 (unreliable)
.ata_host_stop+0x74/0xd0 [libata]
.release_nodes+0x330/0x3f0
.device_release_driver_internal+0x178/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
.__se_sys_delete_module+0x1ec/0x2d0
.system_call_exception+0xfc/0x1f0
system_call_common+0xf8/0x200
==================================================================
The triggering of the BUG is shown in the following stack:
driver_detach
device_release_driver_internal
__device_release_driver
drv->remove(dev) --> platform_drv_remove/platform_remove
drv->remove(dev) --> sata_fsl_remove
iounmap(host_priv->hcr_base); <---- unmap
kfree(host_priv); <---- free
devres_release_all
release_nodes
dr->node.release(dev, dr->data) --> ata_host_stop
ap->ops->port_stop(ap) --> sata_fsl_port_stop
ioread32(hcr_base + HCONTROL) <---- UAF
host->ops->host_stop(host)
The iounmap(host_priv->hcr_base) and kfree(host_priv) functions should
not be executed in drv->remove. These functions should be executed in
host_stop after port_stop. Therefore, we move these functions to the
new function sata_fsl_host_stop and bind the new function to host_stop.
Fixes: faf0b2e5afe7 ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2c1b5a84669d2477d8fffe9136e86a2cff591729 upstream.
When I hot added a CPU, I found 'cpufreq' directory was not created
below /sys/devices/system/cpu/cpuX/.
It is because get_cpu_device() failed in add_cpu_dev_symlink().
cpufreq_add_dev() is the .add_dev callback of a CPU subsys interface.
It will be called when the CPU device registered into the system.
The call chain is as follows:
register_cpu()
->device_register()
->device_add()
->bus_probe_device()
->cpufreq_add_dev()
But only after the CPU device has been registered, we can get the
CPU device by get_cpu_device(), otherwise it will return NULL.
Since we already have the CPU device in cpufreq_add_dev(), pass
it to add_cpu_dev_symlink().
I noticed that the 'kobj' of the CPU device has been added into
the system before cpufreq_add_dev().
Fixes: 2f0ba790df51 ("cpufreq: Fix creation of symbolic links to policy directories")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d49eb91e86e8c1c1614c72e3e958b6b7e2472a9 upstream.
Currently when removing an ipmi_user the removal is deferred as a work on
the system's workqueue. Although this guarantees the free operation will
occur in non atomic context, it can race with the ipmi_msghandler module
removal (see [1]) . In case a remove_user work is scheduled for removal
and shortly after ipmi_msghandler module is removed we can end up in a
situation where the module is removed fist and when the work is executed
the system crashes with :
BUG: unable to handle page fault for address: ffffffffc05c3450
PF: supervisor instruction fetch in kernel mode
PF: error_code(0x0010) - not-present page
because the pages of the module are gone. In cleanup_ipmi() there is no
easy way to detect if there are any pending works to flush them before
removing the module. This patch creates a separate workqueue and schedules
the remove_work works on it. When removing the module the workqueue is
drained when destroyed to avoid the race.
[1] https://bugs.launchpad.net/bugs/1950666
Cc: stable@vger.kernel.org # 5.1
Fixes: 3b9a907223d7 (ipmi: fix sleep-in-atomic in free_user at cleanup SRCU user->release_barrier)
Signed-off-by: Ioanna Alifieraki <ioanna-maria.alifieraki@canonical.com>
Message-Id: <20211115131645.25116-1-ioanna-maria.alifieraki@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed53ae75693096f1c10b4561edd31a07b631bd72 upstream.
As reported by Exuvo is possible that we have lot's of EPROTO errors
during device start i.e. firmware load. But after that device works
correctly. Hence marking device gone by few EPROTO errors done by
commit e383c70474db ("rt2x00: check number of EPROTO errors") caused
regression - Exuvo device stop working after kernel update. To fix
disable the check during device start.
Link: https://lore.kernel.org/linux-wireless/bff7d309-a816-6a75-51b6-5928ef4f7a8c@exuvo.se/
Reported-and-tested-by: Exuvo <exuvo@exuvo.se>
Fixes: e383c70474db ("rt2x00: check number of EPROTO errors")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111141003.GA134627@wp.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee201011c1e1563c114a55c86eb164b236f18e84 upstream.
IPCB/IP6CB need to be initialized when processing outbound v4 or v6 pkts
in the codepath of vrf device xmit function so that leftover garbage
doesn't cause futher code that uses the CB to incorrectly process the
pkt.
One occasion of the issue might occur when MPLS route uses the vrf
device as the outgoing device such as when the route is added using "ip
-f mpls route add <label> dev <vrf>" command.
The problems seems to exist since day one. Hence I put the day one
commits on the Fixes tags.
Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Fixes: 35402e313663 ("net: Add IPv6 support to VRF device")
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211130162637.3249-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
type3_infoblock()
[ Upstream commit 0fa68da72c3be09e06dd833258ee89c33374195f ]
The definition of macro MOTO_SROM_BUG is:
#define MOTO_SROM_BUG (lp->active == 8 && (get_unaligned_le32(
dev->dev_addr) & 0x00ffffff) == 0x3e0008)
and the if statement
if (MOTO_SROM_BUG) lp->active = 0;
using this macro indicates lp->active could be 8. If lp->active is 8 and
the second comparison of this macro is false. lp->active will remain 8 in:
lp->phy[lp->active].gep = (*p ? p : NULL); p += (2 * (*p) + 1);
lp->phy[lp->active].rst = (*p ? p : NULL); p += (2 * (*p) + 1);
lp->phy[lp->active].mc = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].ana = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].fdx = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].ttm = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].mci = *p;
However, the length of array lp->phy is 8, so array overflows can occur.
To fix these possible array overflows, we first check lp->active and then
return -EINVAL if it is greater or equal to ARRAY_SIZE(lp->phy) (i.e. 8).
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
bound
[ Upstream commit 61217be886b5f7402843677e4be7e7e83de9cb41 ]
In line 5001, if all id in the array 'lp->phy[8]' is not 0, when the
'for' end, the 'k' is 8.
At this time, the array 'lp->phy[8]' may be out of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
hns_dsaf_ge_srst_by_port()
[ Upstream commit a66998e0fbf213d47d02813b9679426129d0d114 ]
The if statement:
if (port >= DSAF_GE_NUM)
return;
limits the value of port less than DSAF_GE_NUM (i.e., 8).
However, if the value of port is 6 or 7, an array overflow could occur:
port_rst_off = dsaf_dev->mac_cb[port]->port_rst_off;
because the length of dsaf_dev->mac_cb is DSAF_MAX_PORT_NUM (i.e., 6).
To fix this possible array overflow, we first check port and if it is
greater than or equal to DSAF_MAX_PORT_NUM, the function returns.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1527f69204fe35f341cb599f1cb01bd02daf4374 ]
AMD requires that the SATA controller be configured for devsleep in order
for S0i3 entry to work properly.
commit b1a9585cc396 ("ata: ahci: Enable DEVSLP by default on x86 with
SLP_S0") sets up a kernel policy to enable devsleep on Intel mobile
platforms that are using s0ix. Add the PCI ID for the SATA controller in
Green Sardine platforms to extend this policy by default for AMD based
systems using s0i3 as well.
Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a0c2f8b6709a9a4af175497ca65f93804f57b248 ]
We can race where iscsi_session_recovery_timedout() has woken up the error
handler thread and it's now setting the devices to offline, and
session_recovery_timedout()'s call to scsi_target_unblock() is also trying
to set the device's state to transport-offline. We can then get a mix of
states.
For the case where we can't relogin we want the devices to be in
transport-offline so when we have repaired the connection
__iscsi_unblock_session() can set the state back to running.
Set the device state then call into libiscsi to wake up the error handler.
Link: https://lore.kernel.org/r/20211105221048.6541-2-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 99b63316c39988039965693f5f43d8b4ccb1c86c ]
During the suspend is in process, thermal_zone_device_update bails out
thermal zone re-evaluation for any sensor trip violation without
setting next valid trip to that sensor. It assumes during resume
it will re-evaluate same thermal zone and update trip. But when it is
in suspend temperature goes down and on resume path while updating
thermal zone if temperature is less than previously violated trip,
thermal zone set trip function evaluates the same previous high and
previous low trip as new high and low trip. Since there is no change
in high/low trip, it bails out from thermal zone set trip API without
setting any trip. It leads to a case where sensor high trip or low
trip is disabled forever even though thermal zone has a valid high
or low trip.
During thermal zone device init, reset thermal zone previous high
and low trip. It resolves above mentioned scenario.
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 39f53292181081d35174a581a98441de5da22bc9 ]
When WWAN device wake from S3 deep, under thinkpad platform,
WWAN would be disabled. This disable status could be checked
by command 'nmcli r wwan' or 'rfkill list'.
Issue analysis as below:
When host resume from S3 deep, thinkpad_acpi driver would
call hotkey_resume() function. Finnaly, it will use
wan_get_status to check the current status of WWAN device.
During this resume progress, wan_get_status would always
return off even WWAN boot up completely.
In patch V2, Hans said 'sw_state should be unchanged
after a suspend/resume. It's better to drop the
tpacpi_rfk_update_swstate call all together from the
resume path'.
And it's confimed by Lenovo that GWAN is no longer
available from WHL generation because the design does not
match with current pin control.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Link: https://lore.kernel.org/r/20211108060648.8212-1-slark_xiao@163.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b922f622592af76b57cbc566eaeccda0b31a3496 ]
This bug report shows up when running our research tools. The
reports is SOOB read, but it seems SOOB write is also possible
a few lines below.
In details, fw.len and sw.len are inputs coming from io. A len
over the size of self->rpc triggers SOOB. The patch fixes the
bugs by adding sanity checks.
The bugs are triggerable with compromised/malfunctioning devices.
They are potentially exploitable given they first leak up to
0xffff bytes and able to overwrite the region later.
The patch is tested with QEMU emulater.
This is NOT tested with a real device.
Attached is the log we found by fuzzing.
BUG: KASAN: slab-out-of-bounds in
hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
Read of size 4 at addr ffff888016260b08 by task modprobe/213
CPU: 0 PID: 213 Comm: modprobe Not tainted 5.6.0 #1
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
__kasan_report.cold+0x37/0x7c
? aq_hw_read_reg_bit+0x60/0x70 [atlantic]
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
kasan_report+0xe/0x20
hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
hw_atl_utils_fw_rpc_call+0x95/0x130 [atlantic]
hw_atl_utils_fw_rpc_wait+0x176/0x210 [atlantic]
hw_atl_utils_mpi_create+0x229/0x2e0 [atlantic]
? hw_atl_utils_fw_rpc_wait+0x210/0x210 [atlantic]
? hw_atl_utils_initfw+0x9f/0x1c8 [atlantic]
hw_atl_utils_initfw+0x12a/0x1c8 [atlantic]
aq_nic_ndev_register+0x88/0x650 [atlantic]
? aq_nic_ndev_init+0x235/0x3c0 [atlantic]
aq_pci_probe+0x731/0x9b0 [atlantic]
? aq_pci_func_init+0xc0/0xc0 [atlantic]
local_pci_probe+0xd3/0x160
pci_device_probe+0x23f/0x3e0
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bb162bb2b4394108c8f055d1b115735331205e28 ]
When PHY_SUN6I_MIPI_DPHY is selected, and RESET_CONTROLLER
is not selected, Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for PHY_SUN6I_MIPI_DPHY
Depends on [n]: (ARCH_SUNXI [=n] || COMPILE_TEST [=y]) && HAS_IOMEM [=y] && COMMON_CLK [=y] && RESET_CONTROLLER [=n]
Selected by [y]:
- DRM_SUN6I_DSI [=y] && HAS_IOMEM [=y] && DRM_SUN4I [=y]
This is because DRM_SUN6I_DSI selects PHY_SUN6I_MIPI_DPHY
without selecting or depending on RESET_CONTROLLER, despite
PHY_SUN6I_MIPI_DPHY depending on RESET_CONTROLLER.
These unmet dependency bugs were detected by Kismet,
a static analysis tool for Kconfig. Please advise if this
is not the appropriate solution.
v2:
Fixed indentation to match the rest of the file.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211109032351.43322-1-julianbraha@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e679004dec37566f658a255157d3aed9d762a2b7 upstream.
Xen frontends shouldn't BUG() in case of illegal data received from
their backends. So replace the BUG_ON()s when reading illegal data from
the ring page with negative return values.
This is commit e679004dec37566f upstream.
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20210707091045.460-1-jgross@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a884daa61a7d91650987e855464526aef219590f upstream.
Today netfront will trust the backend to send only sane response data.
In order to avoid privilege escalations or crashes in case of malicious
backends verify the data to be within expected limits. Especially make
sure that the response always references an outstanding request.
Note that only the tx queue needs special id handling, as for the rx
queue the id is equal to the index in the ring page.
Introduce a new indicator for the device whether it is broken and let
the device stop working when it is set. Set this indicator in case the
backend sets any weird data.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 21631d2d741a64a073e167c27769e73bc7844a2f upstream.
The tx_skb_freelist elements are in a single linked list with the
request id used as link reference. The per element link field is in a
union with the skb pointer of an in use request.
Move the link reference out of the union in order to enable a later
reuse of it for requests which need a populated skb pointer.
Rename add_id_to_freelist() and get_id_from_freelist() to
add_id_to_list() and get_id_from_list() in order to prepare using
those for other lists as well. Define ~0 as value to indicate the end
of a list and place that value into the link for a request not being
on the list.
When freeing a skb zero the skb pointer in the request. Use a NULL
value of the skb pointer instead of skb_entry_is_link() for deciding
whether a request has a skb linked to it.
Remove skb_entry_set_link() and open code it instead as it is really
trivial now.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 162081ec33c2686afa29d91bf8d302824aa846c7 upstream.
In order to avoid a malicious backend being able to influence the local
processing of a request build the request locally first and then copy
it to the ring page. Any reading from the request influencing the
processing in the frontend needs to be done on the local instance.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8446066bf8c1f9f7b7412c43fbea0fb87464d75b upstream.
In order to avoid problems in case the backend is modifying a response
on the ring page while the frontend has already seen it, just read the
response into a local buffer in one go and then operate on that buffer
only.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b94e4b147fd1992ad450e1fea1fdaa3738753373 upstream.
Today blkfront will trust the backend to send only sane response data.
In order to avoid privilege escalations or crashes in case of malicious
backends verify the data to be within expected limits. Especially make
sure that the response always references an outstanding request.
Introduce a new state of the ring BLKIF_STATE_ERROR which will be
switched to in case an inconsistency is being detected. Recovering from
this state is possible only via removing and adding the virtual device
again (e.g. via a suspend/resume cycle).
Make all warning messages issued due to valid error responses rate
limited in order to avoid message floods being triggered by a malicious
backend.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20210730103854.12681-4-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f5a695d99000fc3aa73934d7ced33cfc64dcdab upstream.
In order to avoid a malicious backend being able to influence the local
copy of a request build the request locally first and then copy it to
the ring page instead of doing it the other way round as today.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20210730103854.12681-3-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 71b66243f9898d0e54296b4e7035fb33cdcb0707 upstream.
In order to avoid problems in case the backend is modifying a response
on the ring page while the frontend has already seen it, just read the
response into a local buffer in one go and then operate on that buffer
only.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20210730103854.12681-2-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49d8c5ffad07ca014cfae72a1b9b8c52b6ad9cb8 upstream.
The "used length" reported by calling vhost_add_used() must be the
number of bytes written by the device (using "in" buffers).
In vhost_vsock_handle_tx_kick() the device only reads the guest
buffers (they are all "out" buffers), without writing anything,
so we must pass 0 as "used length" to comply virtio spec.
Fixes: 433fc58e6bf2 ("VSOCK: Introduce vhost_vsock.ko")
Cc: stable@vger.kernel.org
Reported-by: Halil Pasic <pasic@linux.ibm.com>
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20211122163525.294024-2-sgarzare@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c49a35eedfef08bffd46b53c25dbf9d6016a86ff ]
The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a075464d1e9317ffae0973dfe538a7511291a06 ]
The ocelot driver, when asked to timestamp all receiving packets, 1588
v1 or NTP, says "nah, here's 1588 v2 for you".
According to this discussion:
https://patchwork.kernel.org/project/netdevbpf/patch/20211104133204.19757-8-martin.kaistra@linutronix.de/#24577647
drivers that downgrade from a wider request to a narrower response (or
even a response where the intersection with the request is empty) are
buggy, and should return -ERANGE instead. This patch fixes that.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d2ad993aa05c0768f00c886c9d369cd97a337ac ]
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eaeace60778e524a2820d0c0ad60bf80289e292c ]
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.
Danielle brought this back up as still occurring, so we'll try
again.
[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0
As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.
Fixes: 16eb8815c235 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c024b226a417c4eb9353ff500b1c823165d4d508 ]
Submit I/O requests with the IOCB_NOWAIT flag set only if
the underlying filesystem supports it.
Fixes: 50a909db36f2 ("nvmet: use IOCB_NOWAIT for file-ns buffered I/O")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
